Required root node properties:
- compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220";
+ HiP05 D02 Board
+ Required root node properties:
+ - compatible = "hisilicon,hip05-d02";
+
Hisilicon system controller
Required properties:
reboot-offset = <0x4>;
};
+-----------------------------------------------------------------------
+Hisilicon HiP05 PCIe-SAS system controller
+
+Required properties:
+- compatible : "hisilicon,pcie-sas-subctrl", "syscon";
+- reg : Register address and size
+
+The HiP05 PCIe-SAS system controller is shared by PCIe and SAS controllers in
+HiP05 Soc to implement some basic configurations.
+
+Example:
+ /* for HiP05 PCIe-SAS system */
+ pcie_sas: system_controller@0xb0000000 {
+ compatible = "hisilicon,pcie-sas-subctrl", "syscon";
+ reg = <0xb0000000 0x10000>;
+ };
+
-----------------------------------------------------------------------
Hisilicon CPU controller
Required properties:
- compatible : should be one of
+ "apm,potenza-pmu"
"arm,armv8-pmuv3"
+ "arm.cortex-a57-pmu"
+ "arm.cortex-a53-pmu"
"arm,cortex-a17-pmu"
"arm,cortex-a15-pmu"
"arm,cortex-a12-pmu"
-* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator
+* Samsung S2MPS11/13/14/15 and S2MPU02 Voltage and Current Regulator
The Samsung S2MPS11 is a multi-function device which includes voltage and
current regulators, RTC, charger controller and other sub-blocks. It is
addressed by the host system using different I2C slave addresses.
Required properties:
-- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic"
- or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic".
+- compatible: Should be one of the following
+ - "samsung,s2mps11-pmic"
+ - "samsung,s2mps13-pmic"
+ - "samsung,s2mps14-pmic"
+ - "samsung,s2mps15-pmic"
+ - "samsung,s2mpu02-pmic".
- reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
Optional properties:
- interrupt-parent: Specifies the phandle of the interrupt controller to which
the interrupts from s2mps11 are delivered to.
- interrupts: Interrupt specifiers for interrupt sources.
+- samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled
+ down. When the system is suspended it will always go down thus triggerring
+ unwanted buck warm reset (setting buck voltages to default values).
+ - samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is
+ connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1
+ register to turn off the power. Usually the ACOKB is pulled up to VBATT so
+ when PWRHOLD pin goes low, the rising ACOKB will trigger power off.
Optional nodes:
-- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768
+- clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768
KHz outputs, so to register these as clocks with common clock framework
instantiate a sub-node named "clocks". It uses the common clock binding
documented in :
the clock which they consume.
Clock ID Devices
----------------------------------------------------------
- 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767
- 32KhzCP 1 S2MPS11, S2MPS13, S5M8767
- 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767
+ 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767
+ 32KhzCP 1 S2MPS11, S2MPS13, S2MPS15, S5M8767
+ 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767
- compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk",
"samsung,s2mps14-clk", "samsung,s5m8767-clk"
+ The s2msp15 uses the same compatible as s2mps13, as both provides similar clocks.
- regulators: The regulators of s2mps11 that have to be instantiated should be
included in a sub-node named 'regulators'. Regulator nodes included in this
- S2MPS11: 1 to 38
- S2MPS13: 1 to 40
- S2MPS14: 1 to 25
+ - S2MPS15: 1 to 27
- S2MPU02: 1 to 28
- Example: LDO1, LDO2, LDO28
- BUCKn
- S2MPS11: 1 to 10
- S2MPS13: 1 to 10
- S2MPS14: 1 to 5
+ - S2MPS15: 1 to 10
- S2MPU02: 1 to 7
- Example: BUCK1, BUCK2, BUCK9
synopsys DWC3 CORE
- DWC3- USB3 CONTROLLER
+ DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
+ as described in 'usb/generic.txt'
Required properties:
- compatible: must be "snps,dwc3"
LTSSM during USB3 Compliance mode.
- snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
- snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
+ - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
+ disabling the suspend signal to the PHY.
- snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
utmi_l1_suspend_n, false when asserts utmi_sleep_n
- snps,hird-threshold: HIRD threshold
- snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
+ - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
+ register for post-silicon frame length adjustment when the
+ fladj_30mhz_sdbnd signal is invalid or incorrect.
This is usually a subnode to DWC3 glue to which it is connected.
avic Shanghai AVIC Optoelectronics Co., Ltd.
axis Axis Communications AB
bosch Bosch Sensortec GmbH
+ boundary Boundary Devices Inc.
brcm Broadcom Corporation
buffalo Buffalo, Inc.
calxeda Calxeda
cloudengines Cloud Engines, Inc.
cnm Chips&Media, Inc.
cnxt Conexant Systems, Inc.
+compulab CompuLab Ltd.
cortina Cortina Systems, Inc.
cosmic Cosmic Circuits
crystalfontz Crystalfontz America, Inc.
excito Excito
fcs Fairchild Semiconductor
firefly Firefly
+focaltech FocalTech Systems Co.,Ltd
fsl Freescale Semiconductor
GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc.
gef GE Fanuc Intelligent Platforms Embedded Systems, Inc.
hisilicon Hisilicon Limited.
hit Hitachi Ltd.
hitex Hitex Development Tools
+holt Holt Integrated Circuits, Inc.
honeywell Honeywell
hp Hewlett Packard
i2se I2SE GmbH
phytec PHYTEC Messtechnik GmbH
picochip Picochip Ltd
plathome Plat'Home Co., Ltd.
+ plda PLDA
pixcir PIXCIR MICROELECTRONICS Co., Ltd
+pulsedlight PulsedLight, Inc
powervr PowerVR (deprecated, use img)
qca Qualcomm Atheros, Inc.
qcom Qualcomm Technologies, Inc
schindler Schindler
seagate Seagate Technology PLC
semtech Semtech Corporation
+sgx SGX Sensortech
sharp Sharp Corporation
+sigma Sigma Designs, Inc.
sil Silicon Image
silabs Silicon Laboratories
siliconmitus Silicon Mitus, Inc.
toshiba Toshiba Corporation
toumaz Toumaz
tplink TP-LINK Technologies Co., Ltd.
+ tronfy Tronfy
truly Truly Semiconductors Limited
+upisemi uPI Semiconductor Corp.
usi Universal Scientific Industrial Co., Ltd.
v3 V3 Semiconductor
variscite Variscite Ltd.
S: Maintained
F: drivers/hwmon/abituguru3.c
+ACCES 104-IDIO-16 GPIO DRIVER
+M: "William Breathitt Gray" <vilhelm.gray@gmail.com>
+L: linux-gpio@vger.kernel.org
+S: Maintained
+F: drivers/gpio/gpio-104-idio-16.c
+
ACENIC DRIVER
M: Jes Sorensen <jes@trained-monkey.org>
L: linux-acenic@sunsite.dk
F: drivers/gpu/drm/radeon/radeon_kfd.h
F: include/uapi/linux/kfd_ioctl.h
-AMD MICROCODE UPDATE SUPPORT
-M: Borislav Petkov <bp@alien8.de>
-S: Maintained
-F: arch/x86/kernel/cpu/microcode/amd*
-
AMD XGBE DRIVER
M: Tom Lendacky <thomas.lendacky@amd.com>
L: netdev@vger.kernel.org
F: drivers/net/appletalk/
F: net/appletalk/
+ APPLIED MICRO (APM) X-GENE DEVICE TREE SUPPORT
+ M: Duc Dang <dhdang@apm.com>
+ S: Supported
+ F: arch/arm64/boot/dts/apm/
+
APPLIED MICRO (APM) X-GENE SOC ETHERNET DRIVER
M: Iyappan Subramanian <isubramanian@apm.com>
M: Keyur Chudgar <kchudgar@apm.com>
ARM PMU PROFILING AND DEBUGGING
M: Will Deacon <will.deacon@arm.com>
+R: Mark Rutland <mark.rutland@arm.com>
S: Maintained
-F: arch/arm/kernel/perf_*
+F: arch/arm*/kernel/perf_*
F: arch/arm/oprofile/common.c
-F: arch/arm/kernel/hw_breakpoint.c
-F: arch/arm/include/asm/hw_breakpoint.h
-F: arch/arm/include/asm/perf_event.h
+F: arch/arm*/kernel/hw_breakpoint.c
+F: arch/arm*/include/asm/hw_breakpoint.h
+F: arch/arm*/include/asm/perf_event.h
F: drivers/perf/arm_pmu.c
F: include/linux/perf/arm_pmu.h
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
-ARM/Allwinner A1X SoC support
+ARM/Allwinner sunXi SoC support
M: Maxime Ripard <maxime.ripard@free-electrons.com>
+M: Chen-Yu Tsai <wens@csie.org>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
-N: sun[x4567]i
+N: sun[x456789]i
ARM/Allwinner SoC Clock Support
M: Emilio López <emilio@elopez.com.ar>
S: Maintained
F: arch/arm/mach-alpine/
-ARM/ATMEL AT91RM9200 AND AT91SAM ARM ARCHITECTURES
+ARM/ATMEL AT91RM9200, AT91SAM9 AND SAMA5 SOC SUPPORT
M: Nicolas Ferre <nicolas.ferre@atmel.com>
M: Alexandre Belloni <alexandre.belloni@free-electrons.com>
M: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
M: Joachim Eastwood <manabian@gmail.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
+F: arch/arm/boot/dts/lpc43*
+F: drivers/clk/nxp/clk-lpc18xx*
+F: drivers/clocksource/time-lpc32xx.c
+F: drivers/i2c/busses/i2c-lpc2k.c
+F: drivers/memory/pl172.c
+F: drivers/mtd/spi-nor/nxp-spifi.c
+F: drivers/rtc/rtc-lpc24xx.c
N: lpc18xx
ARM/MAGICIAN MACHINE SUPPORT
N: mtk
K: mediatek
+ARM/Mediatek USB3 PHY DRIVER
+M: Chunfeng Yun <chunfeng.yun@mediatek.com>
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L: linux-mediatek@lists.infradead.org (moderated for non-subscribers)
+S: Maintained
+F: drivers/phy/phy-mt65xx-usb3.c
+
ARM/MICREL KS8695 ARCHITECTURE
M: Greg Ungerer <gerg@uclinux.org>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
F: drivers/*/*/*s3c2410*
F: drivers/spi/spi-s3c*
F: sound/soc/samsung/*
+ F: Documentation/arm/Samsung/
+ F: Documentation/devicetree/bindings/arm/samsung/
+ F: Documentation/devicetree/bindings/sram/samsung-sram.txt
+ F: Documentation/devicetree/bindings/power/pd-samsung.txt
N: exynos
ARM/SAMSUNG MOBILE MACHINE SUPPORT
S: Maintained
F: drivers/media/platform/s5p-tv/
+ARM/SAMSUNG S5P SERIES JPEG CODEC SUPPORT
+M: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
+M: Jacek Anaszewski <j.anaszewski@samsung.com>
+L: linux-arm-kernel@lists.infradead.org
+L: linux-media@vger.kernel.org
+S: Maintained
+F: drivers/media/platform/s5p-jpeg/
+
ARM/SHMOBILE ARM ARCHITECTURE
M: Simon Horman <horms@verge.net.au>
M: Magnus Damm <magnus.damm@gmail.com>
S: Maintained
F: arch/arm/mach-sti/
F: arch/arm/boot/dts/sti*
+F: drivers/char/hw_random/st-rng.c
F: drivers/clocksource/arm_global_timer.c
F: drivers/clocksource/clksrc_st_lpc.c
F: drivers/i2c/busses/i2c-st.c
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/boot/dts/uniphier*
+F: arch/arm/include/asm/hardware/cache-uniphier.h
F: arch/arm/mach-uniphier/
+F: arch/arm/mm/cache-uniphier.c
+F: drivers/i2c/busses/i2c-uniphier*
F: drivers/pinctrl/uniphier/
F: drivers/tty/serial/8250/8250_uniphier.c
N: uniphier
F: Documentation/aoe/
F: drivers/block/aoe/
+ATHEROS 71XX/9XXX GPIO DRIVER
+M: Alban Bedel <albeu@free.fr>
+W: https://github.com/AlbanBedel/linux
+T: git git://github.com/AlbanBedel/linux
+S: Maintained
+F: drivers/gpio/gpio-ath79.c
+F: Documentation/devicetree/bindings/gpio/gpio-ath79.txt
+
ATHEROS ATH GENERIC UTILITIES
M: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
L: linux-wireless@vger.kernel.org
S: Supported
F: drivers/scsi/bnx2i/
-BROADCOM CYGNUS/IPROC ARM ARCHITECTURE
+BROADCOM IPROC ARM ARCHITECTURE
M: Ray Jui <rjui@broadcom.com>
M: Scott Branden <sbranden@broadcom.com>
+M: Jon Mason <jonmason@broadcom.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
L: bcm-kernel-feedback-list@broadcom.com
T: git git://github.com/broadcom/cygnus-linux.git
S: Maintained
N: iproc
N: cygnus
+N: nsp
N: bcm9113*
N: bcm9583*
-N: bcm583*
+N: bcm9585*
+N: bcm9586*
+N: bcm988312
N: bcm113*
+N: bcm583*
+N: bcm585*
+N: bcm586*
+N: bcm88312
BROADCOM BRCMSTB GPIO DRIVER
M: Gregory Fong <gregory.0xf0@gmail.com>
F: drivers/net/ethernet/cisco/enic/
CISCO VIC LOW LATENCY NIC DRIVER
-M: Upinder Malhi <umalhi@cisco.com>
+M: Christian Benvenuti <benve@cisco.com>
+M: Dave Goodell <dgoodell@cisco.com>
S: Supported
-F: drivers/infiniband/hw/usnic
+F: drivers/infiniband/hw/usnic/
CIRRUS LOGIC EP93XX ETHERNET DRIVER
M: Hartley Sweeten <hsweeten@visionengravers.com>
F: Documentation/powerpc/cxl.txt
F: Documentation/ABI/testing/sysfs-class-cxl
+CXLFLASH (IBM Coherent Accelerator Processor Interface CAPI Flash) SCSI DRIVER
+M: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
+M: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
+L: linux-scsi@vger.kernel.org
+S: Supported
+F: drivers/scsi/cxlflash/
+F: include/uapi/scsi/cxlflash_ioctls.h
+F: Documentation/powerpc/cxlflash.txt
+
STMMAC ETHERNET DRIVER
M: Giuseppe Cavallaro <peppe.cavallaro@st.com>
L: netdev@vger.kernel.org
W: http://www.dialog-semiconductor.com/products
S: Supported
F: Documentation/hwmon/da90??
+F: Documentation/devicetree/bindings/sound/da[79]*.txt
F: drivers/gpio/gpio-da90??.c
F: drivers/hwmon/da90??-hwmon.c
F: drivers/iio/adc/da91??-*.c
L: linux-doc@vger.kernel.org
S: Maintained
F: Documentation/
+F: scripts/docproc.c
+F: scripts/kernel-doc*
X: Documentation/ABI/
X: Documentation/devicetree/
X: Documentation/acpi
X: Documentation/power
X: Documentation/spi
X: Documentation/DocBook/media
-T: git git://git.lwn.net/linux-2.6.git docs-next
+T: git git://git.lwn.net/linux.git docs-next
DOUBLETALK DRIVER
M: "James R. Van Zandt" <jrv@vanzandt.mv.com>
F: drivers/gpu/drm/drm_panel.c
F: drivers/gpu/drm/panel/
F: include/drm/drm_panel.h
-F: Documentation/devicetree/bindings/panel/
+F: Documentation/devicetree/bindings/display/panel/
INTEL DRM DRIVERS (excluding Poulsbo, Moorestown and derivative chipsets)
M: Daniel Vetter <daniel.vetter@intel.com>
M: Jani Nikula <jani.nikula@linux.intel.com>
L: intel-gfx@lists.freedesktop.org
L: dri-devel@lists.freedesktop.org
+W: https://01.org/linuxgraphics/
Q: http://patchwork.freedesktop.org/project/intel-gfx/
T: git git://anongit.freedesktop.org/drm-intel
S: Supported
F: include/drm/i915*
F: include/uapi/drm/i915*
+DRM DRIVERS FOR ATMEL HLCDC
+M: Boris Brezillon <boris.brezillon@free-electrons.com>
+L: dri-devel@lists.freedesktop.org
+S: Supported
+F: drivers/gpu/drm/atmel-hlcdc/
+F: Documentation/devicetree/bindings/drm/atmel/
+
DRM DRIVERS FOR EXYNOS
M: Inki Dae <inki.dae@samsung.com>
M: Joonyoung Shim <jy0922.shim@samsung.com>
L: dri-devel@lists.freedesktop.org
S: Supported
F: drivers/gpu/drm/fsl-dcu/
-F: Documentation/devicetree/bindings/video/fsl,dcu.txt
-F: Documentation/devicetree/bindings/panel/nec,nl4827hc19_05b.txt
+F: Documentation/devicetree/bindings/display/fsl,dcu.txt
+F: Documentation/devicetree/bindings/display/panel/nec,nl4827hc19_05b.txt
DRM DRIVERS FOR FREESCALE IMX
M: Philipp Zabel <p.zabel@pengutronix.de>
L: dri-devel@lists.freedesktop.org
S: Maintained
F: drivers/gpu/drm/imx/
-F: Documentation/devicetree/bindings/drm/imx/
+F: drivers/gpu/ipu-v3/
+F: Documentation/devicetree/bindings/display/imx/
+
+DRM DRIVERS FOR GMA500 (Poulsbo, Moorestown and derivative chipsets)
+M: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
+L: dri-devel@lists.freedesktop.org
+T: git git://github.com/patjak/drm-gma500
+S: Maintained
+F: drivers/gpu/drm/gma500
+F: include/drm/gma500*
DRM DRIVERS FOR NVIDIA TEGRA
M: Thierry Reding <thierry.reding@gmail.com>
F: drivers/gpu/host1x/
F: include/linux/host1x.h
F: include/uapi/drm/tegra_drm.h
-F: Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt
+F: Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
DRM DRIVERS FOR RENESAS
M: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
L: dri-devel@lists.freedesktop.org
S: Maintained
F: drivers/gpu/drm/rockchip/
-F: Documentation/devicetree/bindings/video/rockchip*
+F: Documentation/devicetree/bindings/display/rockchip*
DRM DRIVERS FOR STI
M: Benjamin Gaignard <benjamin.gaignard@linaro.org>
T: git http://git.linaro.org/people/benjamin.gaignard/kernel.git
S: Maintained
F: drivers/gpu/drm/sti
-F: Documentation/devicetree/bindings/gpu/st,stih4xx.txt
+F: Documentation/devicetree/bindings/display/st,stih4xx.txt
DSBR100 USB FM RADIO DRIVER
M: Alexey Klimov <klimov.linux@gmail.com>
T: git git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon.git
S: Maintained
F: drivers/extcon/
+F: include/linux/extcon/
+F: include/linux/extcon.h
F: Documentation/extcon/
+F: Documentation/devicetree/bindings/extcon/
EXYNOS DP DRIVER
M: Jingoo Han <jingoohan1@gmail.com>
F: include/linux/ipmi-fru.h
K: fmc_d.*register
+FPGA MANAGER FRAMEWORK
+M: Alan Tull <atull@opensource.altera.com>
+S: Maintained
+F: drivers/fpga/
+F: include/linux/fpga/fpga-mgr.h
+W: http://www.rocketboards.org
+
FPU EMULATOR
M: Bill Metzenthen <billm@melbpc.org.au>
W: http://floatingpoint.sourceforge.net/emulator/index.html
T: git git://git.kernel.org/pub/scm/linux/kernel/git/plagnioj/linux-fbdev.git
S: Maintained
F: Documentation/fb/
-F: Documentation/devicetree/bindings/fb/
F: drivers/video/
F: include/video/
F: include/linux/fb.h
S: Maintained
F: drivers/net/ethernet/freescale/ucc_geth*
+FREESCALE eTSEC ETHERNET DRIVER (GIANFAR)
+M: Claudiu Manoil <claudiu.manoil@freescale.com>
+L: netdev@vger.kernel.org
+S: Maintained
+F: drivers/net/ethernet/freescale/gianfar*
+X: drivers/net/ethernet/freescale/gianfar_ptp.c
+F: Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
+
FREESCALE QUICC ENGINE UCC UART DRIVER
M: Timur Tabi <timur@tabi.org>
L: linuxppc-dev@lists.ozlabs.org
F: Documentation/devicetree/bindings/i2c/
F: Documentation/i2c/
F: drivers/i2c/
+F: drivers/i2c/*/
F: include/linux/i2c.h
F: include/linux/i2c-*.h
F: include/uapi/linux/i2c.h
S: Supported
F: drivers/platform/x86/intel_menlow.c
-INTEL IA32 MICROCODE UPDATE SUPPORT
-M: Borislav Petkov <bp@alien8.de>
-S: Maintained
-F: arch/x86/kernel/cpu/microcode/core*
-F: arch/x86/kernel/cpu/microcode/intel*
-
INTEL I/OAT DMA DRIVER
M: Dave Jiang <dave.jiang@intel.com>
R: Dan Williams <dan.j.williams@intel.com>
F: Documentation/networking/README.ipw2200
F: drivers/net/wireless/ipw2x00/
+INTEL(R) TRACE HUB
+M: Alexander Shishkin <alexander.shishkin@linux.intel.com>
+S: Supported
+F: Documentation/trace/intel_th.txt
+F: drivers/hwtracing/intel_th/
+
INTEL(R) TRUSTED EXECUTION TECHNOLOGY (TXT)
M: Richard L Maliszewski <richard.l.maliszewski@intel.com>
M: Gang Wei <gang.wei@intel.com>
INTEL WIRELESS WIFI LINK (iwlwifi)
M: Johannes Berg <johannes.berg@intel.com>
M: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-M: Intel Linux Wireless <ilw@linux.intel.com>
+M: Intel Linux Wireless <linuxwifi@intel.com>
L: linux-wireless@vger.kernel.org
W: http://intellinuxwireless.org
T: git git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi.git
F: drivers/misc/mei/*
F: Documentation/misc-devices/mei/*
+INTEL MIC DRIVERS (mic)
+M: Sudeep Dutt <sudeep.dutt@intel.com>
+M: Ashutosh Dixit <ashutosh.dixit@intel.com>
+S: Supported
+W: https://github.com/sudeepdutt/mic
+W: http://software.intel.com/en-us/mic-developer
+F: include/linux/mic_bus.h
+F: include/linux/scif.h
+F: include/uapi/linux/mic_common.h
+F: include/uapi/linux/mic_ioctl.h
+F include/uapi/linux/scif_ioctl.h
+F: drivers/misc/mic/
+F: drivers/dma/mic_x100_dma.c
+F: drivers/dma/mic_x100_dma.h
+F Documentation/mic/
+
INTEL PMC IPC DRIVER
M: Zha Qipeng<qipeng.zha@intel.com>
L: platform-driver-x86@vger.kernel.org
F: drivers/auxdisplay/ks0108.c
F: include/linux/ks0108.h
+L3MDEV
+M: David Ahern <dsa@cumulusnetworks.com>
+L: netdev@vger.kernel.org
+S: Maintained
+F: net/l3mdev
+F: include/net/l3mdev.h
+
LAPB module
L: linux-x25@vger.kernel.org
S: Orphan
F: include/linux/pmem.h
F: arch/*/include/asm/pmem.h
+LIGHTNVM PLATFORM SUPPORT
+M: Matias Bjorling <mb@lightnvm.io>
+W: http://github/OpenChannelSSD
+S: Maintained
+F: drivers/lightnvm/
+F: include/linux/lightnvm.h
+F: include/uapi/linux/lightnvm.h
+
LINUX FOR IBM pSERIES (RS/6000)
M: Paul Mackerras <paulus@au.ibm.com>
W: http://www.ibm.com/linux/ltc/projects/ppc
S: Maintained
F: drivers/net/dsa/mv88e6352.c
+MARVELL CRYPTO DRIVER
+M: Boris Brezillon <boris.brezillon@free-electrons.com>
+M: Arnaud Ebalard <arno@natisbad.org>
+F: drivers/crypto/marvell/
+S: Maintained
+L: linux-crypto@vger.kernel.org
+
MARVELL GIGABIT ETHERNET DRIVERS (skge/sky2)
M: Mirko Lindner <mlindner@marvell.com>
M: Stephen Hemminger <stephen@networkplumber.org>
S: Maintained
F: drivers/media/radio/radio-maxiradio*
+MCP4531 MICROCHIP DIGITAL POTENTIOMETER DRIVER
+M: Peter Rosin <peda@axentia.se>
+L: linux-iio@vger.kernel.org
+S: Maintained
+F: drivers/iio/potentiometer/mcp4531.c
+
MEDIA DRIVERS FOR RENESAS - VSP1
M: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
L: linux-media@vger.kernel.org
MELLANOX ETHERNET DRIVER (mlx4_en)
M: Amir Vadai <amirv@mellanox.com>
-M: Ido Shamay <idos@mellanox.com>
L: netdev@vger.kernel.org
S: Supported
W: http://www.mellanox.com
F: arch/metag/
F: Documentation/metag/
F: Documentation/devicetree/bindings/metag/
+F: Documentation/devicetree/bindings/interrupt-controller/img,*
F: drivers/clocksource/metag_generic.c
F: drivers/irqchip/irq-metag.c
F: drivers/irqchip/irq-metag-ext.c
F: include/linux/mlx5/
F: drivers/infiniband/hw/mlx5/
+MELEXIS MLX90614 DRIVER
+M: Crt Mori <cmo@melexis.com>
+L: linux-iio@vger.kernel.org
+W: http://www.melexis.com
+S: Supported
+F: drivers/iio/temperature/mlx90614.c
+
MN88472 MEDIA DRIVER
M: Antti Palosaari <crope@iki.fi>
L: linux-media@vger.kernel.org
L: linux-wpan@vger.kernel.org
S: Maintained
F: drivers/net/ieee802154/mrf24j40.c
+F: Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt
MSI LAPTOP SUPPORT
M: "Lee, Chun-Yi" <jlee@suse.com>
F: include/media/mt9v032.h
MULTIFUNCTION DEVICES (MFD)
-M: Samuel Ortiz <sameo@linux.intel.com>
M: Lee Jones <lee.jones@linaro.org>
T: git git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git
S: Supported
F: drivers/net/
F: include/linux/if_*
F: include/linux/netdevice.h
-F: include/linux/arcdevice.h
F: include/linux/etherdevice.h
F: include/linux/fcdevice.h
F: include/linux/fddidevice.h
F: Documentation/filesystems/nilfs2.txt
F: fs/nilfs2/
F: include/linux/nilfs2_fs.h
+F: include/trace/events/nilfs2.h
NINJA SCSI-3 / NINJA SCSI-32Bi (16bit/CardBus) PCMCIA SCSI HOST ADAPTER DRIVER
M: YOKOTA Hiroshi <yokota@netlab.is.tsukuba.ac.jp>
M: Pali Rohár <pali.rohar@gmail.com>
S: Maintained
F: include/linux/power/bq2415x_charger.h
-F: include/linux/power/bq27x00_battery.h
+F: include/linux/power/bq27xxx_battery.h
F: include/linux/power/isp1704_charger.h
F: drivers/power/bq2415x_charger.c
-F: drivers/power/bq27x00_battery.c
+F: drivers/power/bq27xxx_battery.c
F: drivers/power/isp1704_charger.c
F: drivers/power/rx51_battery.c
F: drivers/video/fbdev/nvidia/
NVM EXPRESS DRIVER
-M: Matthew Wilcox <willy@linux.intel.com>
+M: Keith Busch <keith.busch@intel.com>
+M: Jens Axboe <axboe@fb.com>
L: linux-nvme@lists.infradead.org
-T: git git://git.infradead.org/users/willy/linux-nvme.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux-block.git
+W: https://kernel.googlesource.com/pub/scm/linux/kernel/git/axboe/linux-block/
S: Supported
-F: drivers/block/nvme*
+F: drivers/nvme/host/
F: include/linux/nvme.h
NVMEM FRAMEWORK
F: arch/x86/pci/
F: arch/x86/kernel/quirks.c
+PCI DRIVER FOR ALTERA PCIE IP
+M: Ley Foon Tan <lftan@altera.com>
+L: rfi@lists.rocketboards.org (moderated for non-subscribers)
+L: linux-pci@vger.kernel.org
+S: Supported
+F: Documentation/devicetree/bindings/pci/altera-pcie.txt
+F: drivers/pci/host/pcie-altera.c
+
PCI DRIVER FOR ARM VERSATILE PLATFORM
M: Rob Herring <robh@kernel.org>
L: linux-pci@vger.kernel.org
S: Maintained
F: drivers/pci/host/*spear*
+PCI MSI DRIVER FOR ALTERA MSI IP
+M: Ley Foon Tan <lftan@altera.com>
+L: rfi@lists.rocketboards.org (moderated for non-subscribers)
+L: linux-pci@vger.kernel.org
+S: Supported
+F: Documentation/devicetree/bindings/pci/altera-pcie-msi.txt
+F: drivers/pci/host/pcie-altera-msi.c
+
PCI MSI DRIVER FOR APPLIEDMICRO XGENE
M: Duc Dang <dhdang@apm.com>
L: linux-pci@vger.kernel.org
F: Documentation/devicetree/bindings/pci/xgene-pci-msi.txt
F: drivers/pci/host/pci-xgene-msi.c
+PCIE DRIVER FOR HISILICON
+M: Zhou Wang <wangzhou1@hisilicon.com>
+L: linux-pci@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/pci/hisilicon-pcie.txt
+F: drivers/pci/host/pcie-hisi.c
+
PCMCIA SUBSYSTEM
P: Linux PCMCIA Team
L: linux-pcmcia@lists.infradead.org
S: Maintained
F: drivers/pinctrl/pinctrl-at91.*
+PIN CONTROLLER - ATMEL AT91 PIO4
+M: Ludovic Desroches <ludovic.desroches@atmel.com>
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L: linux-gpio@vger.kernel.org
+S: Supported
+F: drivers/pinctrl/pinctrl-at91-pio4.*
+
PIN CONTROLLER - INTEL
M: Mika Westerberg <mika.westerberg@linux.intel.com>
M: Heikki Krogerus <heikki.krogerus@linux.intel.com>
S: Maintained
F: drivers/pnp/
-PNXxxxx I2C DRIVER
-M: Vitaly Wool <vitalywool@gmail.com>
-L: linux-i2c@vger.kernel.org
-S: Maintained
-F: drivers/i2c/busses/i2c-pnx.c
-
PPP PROTOCOL DRIVERS AND COMPRESSORS
M: Paul Mackerras <paulus@samba.org>
L: linux-ppp@vger.kernel.org
S: Supported
F: drivers/net/ethernet/qlogic/qlge/
+QLOGIC QL4xxx ETHERNET DRIVER
+M: Yuval Mintz <Yuval.Mintz@qlogic.com>
+M: Ariel Elior <Ariel.Elior@qlogic.com>
+M: everest-linux-l2@qlogic.com
+L: netdev@vger.kernel.org
+S: Supported
+F: drivers/net/ethernet/qlogic/qed/
+F: include/linux/qed/
+F: drivers/net/ethernet/qlogic/qede/
+
QNX4 FILESYSTEM
M: Anders Larsen <al@alarsen.net>
W: http://www.alarsen.net/linux/qnx4fs/
F: drivers/net/wireless/rtlwifi/
F: drivers/net/wireless/rtlwifi/rtl8192ce/
+RTL8XXXU WIRELESS DRIVER (rtl8xxxu)
+M: Jes Sorensen <Jes.Sorensen@redhat.com>
+L: linux-wireless@vger.kernel.org
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/jes/linux.git rtl8723au-mac80211
+S: Maintained
+F: drivers/net/wireless/realtek/rtl8xxxu/
+
S3 SAVAGE FRAMEBUFFER DRIVER
M: Antonino Daplas <adaplas@gmail.com>
L: linux-fbdev@vger.kernel.org
F: include/net/iucv/
F: net/iucv/
+S390 IOMMU (PCI)
+M: Gerald Schaefer <gerald.schaefer@de.ibm.com>
+L: linux-s390@vger.kernel.org
+W: http://www.ibm.com/developerworks/linux/linux390/
+S: Supported
+F: drivers/iommu/s390-iommu.c
+
S3C24XX SD/MMC Driver
M: Ben Dooks <ben-linux@fluff.org>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
F: Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
F: drivers/net/ethernet/synopsys/dwc_eth_qos.c
+SYNOPSYS DESIGNWARE I2C DRIVER
+M: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
+M: Jarkko Nikula <jarkko.nikula@linux.intel.com>
+M: Mika Westerberg <mika.westerberg@linux.intel.com>
+L: linux-i2c@vger.kernel.org
+S: Maintained
+F: drivers/i2c/busses/i2c-designware-*
+F: include/linux/platform_data/i2c-designware.h
+
SYNOPSYS DESIGNWARE MMC/SD/SDIO DRIVER
M: Seungwon Jeon <tgih.jun@samsung.com>
M: Jaehoon Chung <jh80.chung@samsung.com>
F: include/linux/mmc/dw_mmc.h
F: drivers/mmc/host/dw_mmc*
+SYSTEM TRACE MODULE CLASS
+M: Alexander Shishkin <alexander.shishkin@linux.intel.com>
+S: Maintained
+F: Documentation/trace/stm.txt
+F: drivers/hwtracing/stm/
+F: include/linux/stm.h
+F: include/uapi/linux/stm.h
+
THUNDERBOLT DRIVER
M: Andreas Noever <andreas.noever@gmail.com>
S: Maintained
S: Supported
F: arch/score/
+SYSTEM CONTROL & POWER INTERFACE (SCPI) Message Protocol drivers
+M: Sudeep Holla <sudeep.holla@arm.com>
+L: linux-arm-kernel@lists.infradead.org
+S: Maintained
+F: Documentation/devicetree/bindings/arm/arm,scpi.txt
+F: drivers/clk/clk-scpi.c
+F: drivers/cpufreq/scpi-cpufreq.c
+F: drivers/firmware/arm_scpi.c
+F: include/linux/scpi_protocol.h
+
SCSI CDROM DRIVER
M: Jens Axboe <axboe@kernel.dk>
L: linux-scsi@vger.kernel.org
SERVER ENGINES 10Gbps iSCSI - BladeEngine 2 DRIVER
M: Jayamohan Kallickal <jayamohan.kallickal@avagotech.com>
-M: Minh Tran <minh.tran@avagotech.com>
-M: John Soni Jose <sony.john-n@avagotech.com>
+M: Ketan Mukadam <ketan.mukadam@avagotech.com>
+M: John Soni Jose <sony.john@avagotech.com>
L: linux-scsi@vger.kernel.org
W: http://www.avagotech.com
S: Supported
M: Hans de Goede <hdegoede@redhat.com>
L: linux-fbdev@vger.kernel.org
S: Maintained
-F: Documentation/devicetree/bindings/video/simple-framebuffer.txt
+F: Documentation/devicetree/bindings/display/simple-framebuffer.txt
F: drivers/video/fbdev/simplefb.c
F: include/linux/platform_data/simplefb.h
STAGING - WILC1000 WIFI DRIVER
M: Johnny Kim <johnny.kim@atmel.com>
-M: Rachel Kim <rachel.kim@atmel.com>
-M: Dean Lee <dean.lee@atmel.com>
+M: Austin Shin <austin.shin@atmel.com>
M: Chris Park <chris.park@atmel.com>
+M: Tony Cho <tony.cho@atmel.com>
+M: Glen Lee <glen.lee@atmel.com>
+M: Leo Kim <leo.kim@atmel.com>
L: linux-wireless@vger.kernel.org
S: Supported
F: drivers/staging/wilc1000/
SYNOPSYS ARC ARCHITECTURE
M: Vineet Gupta <vgupta@synopsys.com>
+L: linux-snps-arc@lists.infraded.org
S: Supported
F: arch/arc/
F: Documentation/devicetree/bindings/arc/*
+F: Documentation/devicetree/bindings/interrupt-controller/snps,arc*
F: drivers/tty/serial/arc_uart.c
T: git git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc.git
S: Maintained
F: drivers/platform/x86/toshiba_haps.c
+TOSHIBA WMI HOTKEYS DRIVER
+M: Azael Avalos <coproscefalo@gmail.com>
+L: platform-driver-x86@vger.kernel.org
+S: Maintained
+F: drivers/platform/x86/toshiba-wmi.c
+
TOSHIBA SMM DRIVER
M: Jonathan Buzzard <jonathan@buzzard.org.uk>
W: http://www.buzzard.org.uk/toshiba/
TPM DEVICE DRIVER
M: Peter Huewe <peterhuewe@gmx.de>
M: Marcel Selhorst <tpmdd@selhorst.net>
+M: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
R: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
W: http://tpmdd.sourceforge.net
L: tpmdd-devel@lists.sourceforge.net (moderated for non-subscribers)
F: Documentation/fb/uvesafb.txt
F: drivers/video/fbdev/uvesafb.*
+VF610 NAND DRIVER
+M: Stefan Agner <stefan@agner.ch>
+L: linux-mtd@lists.infradead.org
+S: Supported
+F: drivers/mtd/nand/vf610_nfc.c
+
VFAT/FAT/MSDOS FILESYSTEM
M: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
S: Maintained
F: drivers/media/v4l2-core/videobuf2-*
F: include/media/videobuf2-*
+VIRTUAL SERIO DEVICE DRIVER
+M: Stephen Chandler Paul <thatslyude@gmail.com>
+S: Maintained
+F: drivers/input/serio/userio.c
+F: include/uapi/linux/userio.h
+
VIRTIO CONSOLE DRIVER
M: Amit Shah <amit.shah@redhat.com>
L: virtualization@lists.linux-foundation.org
S: Maintained
F: drivers/net/ethernet/via/via-velocity.*
+VIRT LIB
+M: Alex Williamson <alex.williamson@redhat.com>
+M: Paolo Bonzini <pbonzini@redhat.com>
+L: kvm@vger.kernel.org
+S: Supported
+F: virt/lib/
+
VIVID VIRTUAL VIDEO DRIVER
M: Hans Verkuil <hverkuil@xs4all.nl>
L: linux-media@vger.kernel.org
L: netdev@vger.kernel.org
S: Maintained
F: drivers/net/vrf.c
-F: include/net/vrf.h
F: Documentation/networking/vrf.txt
VT1211 HARDWARE MONITOR DRIVER
W: https://github.com/CirrusLogic/linux-drivers/wiki
S: Supported
F: Documentation/hwmon/wm83??
+F: Documentation/devicetree/bindings/extcon/extcon-arizona.txt
+F: Documentation/devicetree/bindings/regulator/arizona-regulator.txt
+F: Documentation/devicetree/bindings/mfd/arizona.txt
F: arch/arm/mach-s3c64xx/mach-crag6410*
F: drivers/clk/clk-wm83*.c
F: drivers/extcon/extcon-arizona.c
T: git git://git.infradead.org/users/dvhart/linux-platform-drivers-x86.git
S: Maintained
F: drivers/platform/x86/
+F: drivers/platform/olpc/
X86 MCE INFRASTRUCTURE
M: Tony Luck <tony.luck@intel.com>
S: Maintained
F: arch/x86/kernel/cpu/mcheck/*
+X86 MICROCODE UPDATE SUPPORT
+M: Borislav Petkov <bp@alien8.de>
+S: Maintained
+F: arch/x86/kernel/cpu/microcode/*
+
X86 VDSO
M: Andy Lutomirski <luto@amacapital.net>
L: linux-kernel@vger.kernel.org
ZSMALLOC COMPRESSED SLAB MEMORY ALLOCATOR
M: Minchan Kim <minchan@kernel.org>
M: Nitin Gupta <ngupta@vflare.org>
+R: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
L: linux-mm@kvack.org
S: Maintained
F: mm/zsmalloc.c
axm5516-amarillo.dtb
dtb-$(CONFIG_ARCH_BCM2835) += \
bcm2835-rpi-b.dtb \
- bcm2835-rpi-b-plus.dtb
+ bcm2835-rpi-b-rev2.dtb \
+ bcm2835-rpi-b-plus.dtb \
+ bcm2835-rpi-a-plus.dtb
dtb-$(CONFIG_ARCH_BCM_5301X) += \
bcm4708-asus-rt-ac56u.dtb \
bcm4708-asus-rt-ac68u.dtb \
bcm47081-buffalo-wzr-900dhp.dtb \
bcm4709-asus-rt-ac87u.dtb \
bcm4709-buffalo-wxr-1900dhp.dtb \
+ bcm4709-netgear-r7000.dtb \
bcm4709-netgear-r8000.dtb
dtb-$(CONFIG_ARCH_BCM_63XX) += \
bcm963138dvt.dtb
dtb-$(CONFIG_ARCH_BCM_MOBILE) += \
bcm28155-ap.dtb \
bcm21664-garnet.dtb
+ dtb-$(CONFIG_ARCH_BCM_NSP) += \
+ bcm958625k.dtb
dtb-$(CONFIG_ARCH_BERLIN) += \
berlin2-sony-nsz-gs7.dtb \
berlin2cd-google-chromecast.dtb \
exynos5250-arndale.dtb \
exynos5250-smdk5250.dtb \
exynos5250-snow.dtb \
+ exynos5250-snow-rev5.dtb \
exynos5250-spring.dtb \
exynos5260-xyref5260.dtb \
exynos5410-smdk5410.dtb \
exynos5420-smdk5420.dtb \
exynos5422-odroidxu3.dtb \
exynos5422-odroidxu3-lite.dtb \
+ exynos5422-odroidxu4.dtb \
exynos5440-sd5v1.dtb \
exynos5440-ssdk5440.dtb \
exynos5800-peach-pi.dtb
pxa168-aspenite.dtb \
pxa910-dkb.dtb \
mmp2-brownstone.dtb
+ dtb-$(CONFIG_MACH_MESON8B) += \
+ meson8b-mxq.dtb \
+ meson8b-odroidc1.dtb
dtb-$(CONFIG_ARCH_MOXART) += \
moxart-uc7112lx.dtb
dtb-$(CONFIG_SOC_IMX1) += \
imx6dl-gw551x.dtb \
imx6dl-gw552x.dtb \
imx6dl-hummingboard.dtb \
+ imx6dl-nit6xlite.dtb \
imx6dl-nitrogen6x.dtb \
imx6dl-phytec-pbab01.dtb \
imx6dl-rex-basic.dtb \
imx6q-gw552x.dtb \
imx6q-hummingboard.dtb \
imx6q-nitrogen6x.dtb \
+ imx6q-nitrogen6_max.dtb \
imx6q-phytec-pbab01.dtb \
imx6q-rex-pro.dtb \
imx6q-sabreauto.dtb \
am335x-base0033.dtb \
am335x-bone.dtb \
am335x-boneblack.dtb \
+ am335x-bonegreen.dtb \
am335x-sl50.dtb \
am335x-evm.dtb \
am335x-evmsk.dtb \
am437x-gp-evm.dtb
dtb-$(CONFIG_SOC_OMAP5) += \
omap5-cm-t54.dtb \
+ omap5-igep0050.dtb \
omap5-sbc-t54.dtb \
omap5-uevm.dtb
dtb-$(CONFIG_SOC_DRA7XX) += \
rk3288-evb-rk808.dtb \
rk3288-firefly-beta.dtb \
rk3288-firefly.dtb \
+ rk3288-popmetal.dtb \
rk3288-r89.dtb \
+ rk3288-rock2-square.dtb \
+ rk3288-veyron-jaq.dtb \
rk3288-veyron-jerry.dtb \
rk3288-veyron-minnie.dtb \
rk3288-veyron-pinky.dtb \
r8a7790-lager.dtb \
r8a7791-henninger.dtb \
r8a7791-koelsch.dtb \
+ r8a7791-porter.dtb \
r8a7793-gose.dtb \
r8a7794-alt.dtb \
r8a7794-silk.dtb \
sun4i-a10-gemei-g9.dtb \
sun4i-a10-hackberry.dtb \
sun4i-a10-hyundai-a7hd.dtb \
+ sun4i-a10-inet1.dtb \
sun4i-a10-inet97fv2.dtb \
+ sun4i-a10-inet9f-rev03.dtb \
sun4i-a10-itead-iteaduino-plus.dtb \
sun4i-a10-jesurun-q5.dtb \
sun4i-a10-marsboard.dtb \
sun4i-a10-mk802.dtb \
sun4i-a10-mk802ii.dtb \
sun4i-a10-olinuxino-lime.dtb \
- sun4i-a10-pcduino.dtb
+ sun4i-a10-pcduino.dtb \
+ sun4i-a10-pcduino2.dtb \
+ sun4i-a10-pov-protab2-ips9.dtb
dtb-$(CONFIG_MACH_SUN5I) += \
+ sun5i-a10s-auxtek-t003.dtb \
sun5i-a10s-auxtek-t004.dtb \
sun5i-a10s-mk802.dtb \
sun5i-a10s-olinuxino-micro.dtb \
sun5i-a10s-r7-tv-dongle.dtb \
+ sun5i-a10s-wobo-i5.dtb \
sun5i-a13-hsg-h702.dtb \
+ sun5i-a13-inet-98v-rev2.dtb \
sun5i-a13-olinuxino.dtb \
sun5i-a13-olinuxino-micro.dtb \
- sun5i-a13-utoo-p66.dtb
+ sun5i-a13-q8-tablet.dtb \
+ sun5i-a13-utoo-p66.dtb \
+ sun5i-r8-chip.dtb
dtb-$(CONFIG_MACH_SUN6I) += \
sun6i-a31-app4-evb1.dtb \
sun6i-a31-colombus.dtb \
sun6i-a31-i7.dtb \
sun6i-a31-m9.dtb \
sun6i-a31-mele-a1000g-quad.dtb \
- sun6i-a31s-cs908.dtb
+ sun6i-a31s-cs908.dtb \
+ sun6i-a31s-primo81.dtb \
+ sun6i-a31s-sina31s.dtb \
+ sun6i-a31s-sinovoip-bpi-m2.dtb \
+ sun6i-a31s-yones-toptech-bs1078-v2.dtb
dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-bananapi.dtb \
sun7i-a20-bananapro.dtb \
sun7i-a20-i12-tvbox.dtb \
sun7i-a20-m3.dtb \
sun7i-a20-mk808c.dtb \
+ sun7i-a20-olimex-som-evb.dtb \
sun7i-a20-olinuxino-lime.dtb \
sun7i-a20-olinuxino-lime2.dtb \
sun7i-a20-olinuxino-micro.dtb \
sun7i-a20-orangepi-mini.dtb \
sun7i-a20-pcduino3.dtb \
sun7i-a20-pcduino3-nano.dtb \
- sun7i-a20-wexler-tab7200.dtb
+ sun7i-a20-wexler-tab7200.dtb \
+ sun7i-a20-wits-pro-a20-dkt.dtb
dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a23-evb.dtb \
+ sun8i-a23-gt90h-v4.dtb \
sun8i-a23-ippo-q8h-v5.dtb \
sun8i-a23-ippo-q8h-v1.2.dtb \
+ sun8i-a23-q8-tablet.dtb \
sun8i-a33-et-q8-v1.6.dtb \
sun8i-a33-ga10h-v1.1.dtb \
sun8i-a33-ippo-q8h-v1.2.dtb \
+ sun8i-a33-q8-tablet.dtb \
sun8i-a33-sinlinx-sina33.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
uniphier-ph1-ld6b-ref.dtb \
uniphier-ph1-pro4-ref.dtb \
uniphier-ph1-sld3-ref.dtb \
- uniphier-ph1-sld8-ref.dtb
+ uniphier-ph1-sld8-ref.dtb \
+ uniphier-proxstream2-gentil.dtb \
+ uniphier-proxstream2-vodka.dtb
dtb-$(CONFIG_ARCH_VERSATILE) += \
versatile-ab.dtb \
versatile-pb.dtb
armada-370-netgear-rn102.dtb \
armada-370-netgear-rn104.dtb \
armada-370-rd.dtb \
+ armada-370-seagate-nas-2bay.dtb \
+ armada-370-seagate-nas-4bay.dtb \
+ armada-370-seagate-personal-cloud.dtb \
+ armada-370-seagate-personal-cloud-2bay.dtb \
armada-370-synology-ds213j.dtb
dtb-$(CONFIG_MACH_ARMADA_375) += \
armada-375-db.dtb
dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
endif
+dtstree := $(srctree)/$(src)
+dtb-$(CONFIG_OF_ALL_DTBS) := $(patsubst $(dtstree)/%.dts,%.dtb, $(wildcard $(dtstree)/*.dts))
+
always := $(dtb-y)
clean-files := *.dtb
reg = <0x38>;
interrupt-parent = <&gpio0>;
- interrupts = <31 0>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
vmmc-supply = <&dcdc4>;
bus-width = <4>;
- cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
};
&usb2_phy1 {
regulator-max-microvolt = <3300000>;
};
+ aic_dvdd: fixedregulator-aic_dvdd {
+ compatible = "regulator-fixed";
+ regulator-name = "aic_dvdd_fixed";
+ vin-supply = <&vdd_3v3>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
vtt_fixed: fixedregulator-vtt {
/* TPS51200 */
compatible = "regulator-fixed";
};
};
};
+
+ sound0: sound@0 {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "BeagleBoard-X15";
+ simple-audio-card,widgets =
+ "Line", "Line Out",
+ "Line", "Line In";
+ simple-audio-card,routing =
+ "Line Out", "LLOUT",
+ "Line Out", "RLOUT",
+ "MIC2L", "Line In",
+ "MIC2R", "Line In";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound0_master>;
+ simple-audio-card,frame-master = <&sound0_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp3>;
+ };
+
+ sound0_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3104>;
+ clocks = <&clkout2_clk>;
+ };
+ };
};
&dra7_pmx_core {
0x370 (PIN_OUTPUT | MUX_MODE14) /* gpio6_28 LS_OE */
>;
};
+
+ clkout2_pins_default: clkout2_pins_default {
+ pinctrl-single,pins = <
+ 0x294 (PIN_OUTPUT_PULLDOWN | MUX_MODE9) /* xref_clk0.clkout2 */
+ >;
+ };
+
+ clkout2_pins_sleep: clkout2_pins_sleep {
+ pinctrl-single,pins = <
+ 0x294 (PIN_INPUT | MUX_MODE15) /* xref_clk0.clkout2 */
+ >;
+ };
+
+ mcasp3_pins_default: mcasp3_pins_default {
+ pinctrl-single,pins = <
+ 0x324 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */
+ 0x328 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */
+ 0x32c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */
+ 0x330 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */
+ >;
+ };
+
+ mcasp3_pins_sleep: mcasp3_pins_sleep {
+ pinctrl-single,pins = <
+ 0x324 (PIN_INPUT | MUX_MODE15)
+ 0x328 (PIN_INPUT | MUX_MODE15)
+ 0x32c (PIN_INPUT | MUX_MODE15)
+ 0x330 (PIN_INPUT | MUX_MODE15)
+ >;
+ };
};
&i2c1 {
/* SMPS9 unused */
ldo1_reg: ldo1 {
- /* VDD_SD */
+ /* VDD_SD / VDDSHV8 */
regulator-name = "ldo1";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
+ regulator-always-on;
};
ldo2_reg: ldo2 {
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
#thermal-sensor-cells = <1>;
};
+
+ tlv320aic3104: tlv320aic3104@18 {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3104";
+ reg = <0x18>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&clkout2_pins_default>;
+ pinctrl-1 = <&clkout2_pins_sleep>;
+ status = "okay";
+ adc-settle-ms = <40>;
+
+ AVDD-supply = <&vdd_3v3>;
+ IOVDD-supply = <&vdd_3v3>;
+ DRVDD-supply = <&vdd_3v3>;
+ DVDD-supply = <&aic_dvdd>;
+ };
};
&i2c3 {
vmmc-supply = <&ldo1_reg>;
bus-width = <4>;
- cd-gpios = <&gpio6 27 0>; /* gpio 219 */
+ cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
};
&mmc2 {
&pcie1 {
gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
};
+
+ &mcasp3 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&mcasp3_pins_default>;
+ pinctrl-1 = <&mcasp3_pins_sleep>;
+ status = "okay";
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 4 serializers */
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 2 0 0
+ >;
+ };
+
+ &mailbox5 {
+ status = "okay";
+ mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
+ status = "okay";
+ };
+ mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
+ status = "okay";
+ };
+ };
+
+ &mailbox6 {
+ status = "okay";
+ mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
+ status = "okay";
+ };
+ mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
+ status = "okay";
+ };
+ };
/ {
model = "Marvell Armada 385 Access Point Development Board";
- compatible = "marvell,a385-db-ap", "marvell,armada385", "marvell,armada38x";
+ compatible = "marvell,a385-db-ap", "marvell,armada385", "marvell,armada380";
chosen {
stdout-path = "serial1:115200n8";
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
- MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+ MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
internal-regs {
spi1: spi@10680 {
model = "Marvell Armada 1500 pro (BG2-Q) SoC";
compatible = "marvell,berlin2q", "marvell,berlin";
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
device_type = "cpu";
next-level-cache = <&l2>;
reg = <0>;
+
+ clocks = <&chip_clk CLKID_CPU>;
+ clock-latency = <100000>;
+ /* Can be modified by the bootloader */
+ operating-points = <
+ /* kHz uV */
+ 1200000 1200000
+ 1000000 1200000
+ 800000 1200000
+ 600000 1200000
+ >;
};
cpu@1 {
};
usb_phy2: phy@a2f400 {
- compatible = "marvell,berlin2-usb-phy";
+ compatible = "marvell,berlin2cd-usb-phy";
reg = <0xa2f400 0x128>;
#phy-cells = <0>;
resets = <&chip_rst 0x104 14>;
};
usb_phy0: phy@b74000 {
- compatible = "marvell,berlin2-usb-phy";
+ compatible = "marvell,berlin2cd-usb-phy";
reg = <0xb74000 0x128>;
#phy-cells = <0>;
resets = <&chip_rst 0x104 12>;
};
usb_phy1: phy@b78000 {
- compatible = "marvell,berlin2-usb-phy";
+ compatible = "marvell,berlin2cd-usb-phy";
reg = <0xb78000 0x128>;
#phy-cells = <0>;
resets = <&chip_rst 0x104 13>;
status = "disabled";
};
+ pwm: pwm@f20000 {
+ compatible = "marvell,berlin-pwm";
+ reg = <0xf20000 0x40>;
+ clocks = <&chip_clk CLKID_CFG>;
+ #pwm-cells = <3>;
+ };
+
apb@fc0000 {
compatible = "simple-bus";
#address-cells = <1>;
#thermal-sensor-cells = <1>;
};
+ dsp1_system: dsp_system@40d00000 {
+ compatible = "syscon";
+ reg = <0x40d00000 0x100>;
+ };
+
sdma: dma-controller@4a056000 {
compatible = "ti,omap4430-sdma";
reg = <0x4a056000 0x1000>;
status = "disabled";
};
+ mmu0_dsp1: mmu@40d01000 {
+ compatible = "ti,dra7-dsp-iommu";
+ reg = <0x40d01000 0x100>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mmu0_dsp1";
+ #iommu-cells = <0>;
+ ti,syscon-mmuconfig = <&dsp1_system 0x0>;
+ status = "disabled";
+ };
+
+ mmu1_dsp1: mmu@40d02000 {
+ compatible = "ti,dra7-dsp-iommu";
+ reg = <0x40d02000 0x100>;
+ interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mmu1_dsp1";
+ #iommu-cells = <0>;
+ ti,syscon-mmuconfig = <&dsp1_system 0x1>;
+ status = "disabled";
+ };
+
+ mmu_ipu1: mmu@58882000 {
+ compatible = "ti,dra7-iommu";
+ reg = <0x58882000 0x100>;
+ interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mmu_ipu1";
+ #iommu-cells = <0>;
+ ti,iommu-bus-err-back;
+ status = "disabled";
+ };
+
+ mmu_ipu2: mmu@55082000 {
+ compatible = "ti,dra7-iommu";
+ reg = <0x55082000 0x100>;
+ interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mmu_ipu2";
+ #iommu-cells = <0>;
+ ti,iommu-bus-err-back;
+ status = "disabled";
+ };
+
abb_mpu: regulator-abb-mpu {
compatible = "ti,abb-v3";
regulator-name = "abb_mpu";
status = "disabled";
};
+ mcasp3: mcasp@48468000 {
+ compatible = "ti,dra7-mcasp-audio";
+ ti,hwmods = "mcasp3";
+ reg = <0x48468000 0x2000>;
+ reg-names = "mpu";
+ interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+ dmas = <&sdma_xbar 133>, <&sdma_xbar 132>;
+ dma-names = "tx", "rx";
+ clocks = <&mcasp3_ahclkx_mux>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
crossbar_mpu: crossbar@4a002a48 {
compatible = "ti,irq-crossbar";
reg = <0x4a002a48 0x130>;
<GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>;
ranges;
+ syscon = <&scm_conf>;
status = "disabled";
davinci_mdio: mdio@48485000 {
regulator-name = "P5.0V_USB3CON0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gph0 0 0>;
+ gpio = <&gph0 0 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb300_vbus_en>;
enable-active-high;
regulator-name = "P5.0V_USB3CON1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gph0 1 0>;
+ gpio = <&gph0 1 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb301_vbus_en>;
enable-active-high;
samsung,color-depth = <1>;
samsung,link-rate = <0x06>;
samsung,lane-count = <2>;
- samsung,hpd-gpio = <&gpx2 6 0>;
+ samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>;
ports {
port@0 {
};
};
+&pmu_system_controller {
+ assigned-clocks = <&pmu_system_controller 0>;
+ assigned-clock-parents = <&clock CLK_FIN_PLL>;
+};
+
&rtc {
status = "okay";
clocks = <&clock CLK_RTC>, <&max77802 MAX77802_CLK_32K_AP>;
status = "okay";
num-cs = <1>;
samsung,spi-src-clk = <0>;
- cs-gpios = <&gpb1 2 0>;
+ cs-gpios = <&gpb1 2 GPIO_ACTIVE_HIGH>;
cros_ec: cros-ec@0 {
compatible = "google,cros-ec-spi";
pinctrl-0 = <&ec_spi_cs &ec_irq>;
reg = <0>;
spi-max-frequency = <3125000>;
+ google,has-vbc-nvram;
controller-data {
samsung,spi-feedback-delay = <1>;
regulator-name = "P5.0V_USB3CON0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gph0 0 0>;
+ gpio = <&gph0 0 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb300_vbus_en>;
enable-active-high;
regulator-name = "P5.0V_USB3CON1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gph0 1 0>;
+ gpio = <&gph0 1 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb301_vbus_en>;
enable-active-high;
samsung,color-depth = <1>;
samsung,link-rate = <0x0a>;
samsung,lane-count = <2>;
- samsung,hpd-gpio = <&gpx2 6 0>;
+ samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>;
panel = <&panel>;
};
};
};
+&pmu_system_controller {
+ assigned-clocks = <&pmu_system_controller 0>;
+ assigned-clock-parents = <&clock CLK_FIN_PLL>;
+};
+
&rtc {
status = "okay";
clocks = <&clock CLK_RTC>, <&max77802 MAX77802_CLK_32K_AP>;
status = "okay";
num-cs = <1>;
samsung,spi-src-clk = <0>;
- cs-gpios = <&gpb1 2 0>;
+ cs-gpios = <&gpb1 2 GPIO_ACTIVE_HIGH>;
cros_ec: cros-ec@0 {
compatible = "google,cros-ec-spi";
pinctrl-0 = <&ec_spi_cs &ec_irq>;
reg = <0>;
spi-max-frequency = <3125000>;
+ google,has-vbc-nvram;
controller-data {
samsung,spi-feedback-delay = <1>;
status = "disabled";
};
+ iomuxc_lpsr: iomuxc-lpsr@302c0000 {
+ compatible = "fsl,imx7d-iomuxc-lpsr";
+ reg = <0x302c0000 0x10000>;
+ fsl,input-sel = <&iomuxc>;
+ };
+
gpt1: gpt@302d0000 {
compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
reg = <0x302d0000 0x10000>;
};
};
+ aips2: aips-bus@30400000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x30400000 0x400000>;
+ ranges;
+
+ pwm1: pwm@30660000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30660000 0x10000>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM1_ROOT_CLK>,
+ <&clks IMX7D_PWM1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@30670000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30670000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM2_ROOT_CLK>,
+ <&clks IMX7D_PWM2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@30680000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30680000 0x10000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM3_ROOT_CLK>,
+ <&clks IMX7D_PWM3_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm4: pwm@30690000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30690000 0x10000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM4_ROOT_CLK>,
+ <&clks IMX7D_PWM4_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+ };
+
aips3: aips-bus@30800000 {
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <1>;
status = "disabled";
};
- uart2: serial@30870000 {
+ uart2: serial@30890000 {
compatible = "fsl,imx7d-uart",
"fsl,imx6q-uart";
- reg = <0x30870000 0x10000>;
+ reg = <0x30890000 0x10000>;
interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX7D_UART2_ROOT_CLK>,
<&clks IMX7D_UART2_ROOT_CLK>;
status = "disabled";
};
+ usbotg1: usb@30b10000 {
+ compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
+ reg = <0x30b10000 0x200>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_USB_CTRL_CLK>;
+ fsl,usbphy = <&usbphynop1>;
+ fsl,usbmisc = <&usbmisc1 0>;
+ phy-clkgate-delay-us = <400>;
+ status = "disabled";
+ };
+
+ usbotg2: usb@30b20000 {
+ compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
+ reg = <0x30b20000 0x200>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_USB_CTRL_CLK>;
+ fsl,usbphy = <&usbphynop2>;
+ fsl,usbmisc = <&usbmisc2 0>;
+ phy-clkgate-delay-us = <400>;
+ status = "disabled";
+ };
+
+ usbh: usb@30b30000 {
+ compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
+ reg = <0x30b30000 0x200>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_USB_CTRL_CLK>;
+ fsl,usbphy = <&usbphynop3>;
+ fsl,usbmisc = <&usbmisc3 0>;
+ phy_type = "hsic";
+ dr_mode = "host";
+ phy-clkgate-delay-us = <400>;
+ status = "disabled";
+ };
+
+ usbmisc1: usbmisc@30b10200 {
+ #index-cells = <1>;
+ compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x30b10200 0x200>;
+ };
+
+ usbmisc2: usbmisc@30b20200 {
+ #index-cells = <1>;
+ compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x30b20200 0x200>;
+ };
+
+ usbmisc3: usbmisc@30b30200 {
+ #index-cells = <1>;
+ compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x30b30200 0x200>;
+ };
+
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clks IMX7D_USB_PHY1_CLK>;
+ clock-names = "main_clk";
+ };
+
+ usbphynop2: usbphynop2 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clks IMX7D_USB_PHY2_CLK>;
+ clock-names = "main_clk";
+ };
+
+ usbphynop3: usbphynop3 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>;
+ clock-names = "main_clk";
+ };
+
usdhc1: usdhc@30b40000 {
compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
reg = <0x30b40000 0x10000>;
bus-width = <4>;
status = "disabled";
};
+
+ fec1: ethernet@30be0000 {
+ compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
+ reg = <0x30be0000 0x10000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
+ <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
+ <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ fsl,num-tx-queues=<3>;
+ fsl,num-rx-queues=<3>;
+ status = "disabled";
+ };
+
+ fec2: ethernet@30bf0000 {
+ compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
+ reg = <0x30bf0000 0x10000>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET2_TIME_ROOT_CLK>,
+ <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
+ <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ fsl,num-tx-queues=<3>;
+ fsl,num-rx-queues=<3>;
+ status = "disabled";
+ };
};
};
};
clock-frequency = <19200000>;
};
+ smem {
+ compatible = "qcom,smem";
+
+ memory-region = <&smem_region>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+
+ hwlocks = <&tcsr_mutex 3>;
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
<0xf9002000 0x1000>;
};
+ apcs: syscon@f9011000 {
+ compatible = "syscon";
+ reg = <0xf9011000 0x1000>;
+ };
+
timer@f9020000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "qcom,gcc-msm8974";
#clock-cells = <1>;
#reset-cells = <1>;
+ #power-domain-cells = <1>;
reg = <0xfc400000 0x4000>;
};
compatible = "qcom,mmcc-msm8974";
#clock-cells = <1>;
#reset-cells = <1>;
+ #power-domain-cells = <1>;
reg = <0xfd8c0000 0x6000>;
};
#hwlock-cells = <1>;
};
- smem@fa00000 {
- compatible = "qcom,smem";
-
- memory-region = <&smem_region>;
+ rpm_msg_ram: memory@fc428000 {
+ compatible = "qcom,rpm-msg-ram";
reg = <0xfc428000 0x4000>;
-
- hwlocks = <&tcsr_mutex 3>;
};
blsp1_uart2: serial@f991e000 {
};
blsp_i2c11: i2c@f9967000 {
- status = "disable";
+ status = "disabled";
compatible = "qcom,i2c-qup-v2.1.1";
reg = <0xf9967000 0x1000>;
interrupts = <0 105 IRQ_TYPE_NONE>;
#interrupt-cells = <4>;
};
};
+
+ smd {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <0 168 1>;
+ qcom,ipc = <&apcs 8 0>;
+ qcom,smd-edge = <15>;
+
+ rpm_requests {
+ compatible = "qcom,rpm-msm8974";
+ qcom,smd-channels = "rpm_requests";
+
+ pm8841-regulators {
+ compatible = "qcom,rpm-pm8841-regulators";
+
+ pm8841_s1: s1 {};
+ pm8841_s2: s2 {};
+ pm8841_s3: s3 {};
+ pm8841_s4: s4 {};
+ pm8841_s5: s5 {};
+ pm8841_s6: s6 {};
+ pm8841_s7: s7 {};
+ pm8841_s8: s8 {};
+ };
+
+ pm8941-regulators {
+ compatible = "qcom,rpm-pm8941-regulators";
+
+ pm8941_s1: s1 {};
+ pm8941_s2: s2 {};
+ pm8941_s3: s3 {};
+ pm8941_5v: s4 {};
+
+ pm8941_l1: l1 {};
+ pm8941_l2: l2 {};
+ pm8941_l3: l3 {};
+ pm8941_l4: l4 {};
+ pm8941_l5: l5 {};
+ pm8941_l6: l6 {};
+ pm8941_l7: l7 {};
+ pm8941_l8: l8 {};
+ pm8941_l9: l9 {};
+ pm8941_l10: l10 {};
+ pm8941_l11: l11 {};
+ pm8941_l12: l12 {};
+ pm8941_l13: l13 {};
+ pm8941_l14: l14 {};
+ pm8941_l15: l15 {};
+ pm8941_l16: l16 {};
+ pm8941_l17: l17 {};
+ pm8941_l18: l18 {};
+ pm8941_l19: l19 {};
+ pm8941_l20: l20 {};
+ pm8941_l21: l21 {};
+ pm8941_l22: l22 {};
+ pm8941_l23: l23 {};
+ pm8941_l24: l24 {};
+
+ pm8941_lvs1: lvs1 {};
+ pm8941_lvs2: lvs2 {};
+ pm8941_lvs3: lvs3 {};
+
+ pm8941_5vs1: 5vs1 {};
+ pm8941_5vs2: 5vs2 {};
+ };
+ };
+ };
+ };
};
broken-cd;
bus-width = <8>;
cap-mmc-highspeed;
+ rockchip,default-sample-phase = <158>;
disable-wp;
+ mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
non-removable;
num-slots = <1>;
num-slots = <1>;
pinctrl-names = "default";
pinctrl-0 = <&sdio0_clk &sdio0_cmd &sdio0_bus4>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
vmmc-supply = <&vcc33_sys>;
vqmmc-supply = <&vcc18_wl>;
};
};
};
- /*
- * On Marvell-based hardware this is a no-connect. Make sure we enable
- * the pullup so that the line doesn't float. The pullup shouldn't
- * hurt on Broadcom-based hardware since the other side is actively
- * driving this signal. As proof: we've already got a pullup on RX.
- */
- uart0 {
- uart0_cts: uart0-cts {
- rockchip,pins = <4 18 RK_FUNC_1 &pcfg_pull_up>;
- };
- };
-
write-protect {
fw_wp_ap: fw-wp-ap {
rockchip,pins = <7 6 RK_FUNC_GPIO &pcfg_pull_none>;
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/clock/rk3288-cru.h>
#include <dt-bindings/thermal/thermal.h>
+ #include <dt-bindings/power/rk3288-power.h>
#include "skeleton.dtsi"
/ {
sdmmc: dwmmc@ff0c0000 {
compatible = "rockchip,rk3288-dw-mshc";
clock-freq-min-max = <400000 150000000>;
- clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>;
- clock-names = "biu", "ciu";
+ clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
+ <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
fifo-depth = <0x100>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
reg = <0xff0c0000 0x4000>;
sdio0: dwmmc@ff0d0000 {
compatible = "rockchip,rk3288-dw-mshc";
clock-freq-min-max = <400000 150000000>;
- clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>;
- clock-names = "biu", "ciu";
+ clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>,
+ <&cru SCLK_SDIO0_DRV>, <&cru SCLK_SDIO0_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
fifo-depth = <0x100>;
interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
reg = <0xff0d0000 0x4000>;
sdio1: dwmmc@ff0e0000 {
compatible = "rockchip,rk3288-dw-mshc";
clock-freq-min-max = <400000 150000000>;
- clocks = <&cru HCLK_SDIO1>, <&cru SCLK_SDIO1>;
- clock-names = "biu", "ciu";
+ clocks = <&cru HCLK_SDIO1>, <&cru SCLK_SDIO1>,
+ <&cru SCLK_SDIO1_DRV>, <&cru SCLK_SDIO1_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
fifo-depth = <0x100>;
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
reg = <0xff0e0000 0x4000>;
emmc: dwmmc@ff0f0000 {
compatible = "rockchip,rk3288-dw-mshc";
clock-freq-min-max = <400000 150000000>;
- clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>;
- clock-names = "biu", "ciu";
+ clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
+ <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
fifo-depth = <0x100>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
reg = <0xff0f0000 0x4000>;
};
pmu: power-management@ff730000 {
- compatible = "rockchip,rk3288-pmu", "syscon";
+ compatible = "rockchip,rk3288-pmu", "syscon", "simple-mfd";
reg = <0xff730000 0x100>;
+
+ power: power-controller {
+ compatible = "rockchip,rk3288-power-controller";
+ #power-domain-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /*
+ * Note: Although SCLK_* are the working clocks
+ * of device without including on the NOC, needed for
+ * synchronous reset.
+ *
+ * The clocks on the which NOC:
+ * ACLK_IEP/ACLK_VIP/ACLK_VOP0 are on ACLK_VIO0_NIU.
+ * ACLK_ISP/ACLK_VOP1 are on ACLK_VIO1_NIU.
+ * ACLK_RGA is on ACLK_RGA_NIU.
+ * The others (HCLK_*,PLCK_*) are on HCLK_VIO_NIU.
+ *
+ * Which clock are device clocks:
+ * clocks devices
+ * *_IEP IEP:Image Enhancement Processor
+ * *_ISP ISP:Image Signal Processing
+ * *_VIP VIP:Video Input Processor
+ * *_VOP* VOP:Visual Output Processor
+ * *_RGA RGA
+ * *_EDP* EDP
+ * *_LVDS_* LVDS
+ * *_HDMI HDMI
+ * *_MIPI_* MIPI
+ */
+ pd_vio {
+ reg = <RK3288_PD_VIO>;
+ clocks = <&cru ACLK_IEP>,
+ <&cru ACLK_ISP>,
+ <&cru ACLK_RGA>,
+ <&cru ACLK_VIP>,
+ <&cru ACLK_VOP0>,
+ <&cru ACLK_VOP1>,
+ <&cru DCLK_VOP0>,
+ <&cru DCLK_VOP1>,
+ <&cru HCLK_IEP>,
+ <&cru HCLK_ISP>,
+ <&cru HCLK_RGA>,
+ <&cru HCLK_VIP>,
+ <&cru HCLK_VOP0>,
+ <&cru HCLK_VOP1>,
+ <&cru PCLK_EDP_CTRL>,
+ <&cru PCLK_HDMI_CTRL>,
+ <&cru PCLK_LVDS_PHY>,
+ <&cru PCLK_MIPI_CSI>,
+ <&cru PCLK_MIPI_DSI0>,
+ <&cru PCLK_MIPI_DSI1>,
+ <&cru SCLK_EDP_24M>,
+ <&cru SCLK_EDP>,
+ <&cru SCLK_ISP_JPE>,
+ <&cru SCLK_ISP>,
+ <&cru SCLK_RGA>;
+ };
+
+ /*
+ * Note: The following 3 are HEVC(H.265) clocks,
+ * and on the ACLK_HEVC_NIU (NOC).
+ */
+ pd_hevc {
+ reg = <RK3288_PD_HEVC>;
+ clocks = <&cru ACLK_HEVC>,
+ <&cru SCLK_HEVC_CABAC>,
+ <&cru SCLK_HEVC_CORE>;
+ };
+
+ /*
+ * Note: ACLK_VCODEC/HCLK_VCODEC are VCODEC
+ * (video endecoder & decoder) clocks that on the
+ * ACLK_VCODEC_NIU and HCLK_VCODEC_NIU (NOC).
+ */
+ pd_video {
+ reg = <RK3288_PD_VIDEO>;
+ clocks = <&cru ACLK_VCODEC>,
+ <&cru HCLK_VCODEC>;
+ };
+
+ /*
+ * Note: ACLK_GPU is the GPU clock,
+ * and on the ACLK_GPU_NIU (NOC).
+ */
+ pd_gpu {
+ reg = <RK3288_PD_GPU>;
+ clocks = <&cru ACLK_GPU>;
+ };
+ };
};
sgrf: syscon@ff740000 {
status = "disabled";
};
+ spdif: sound@ff88b0000 {
+ compatible = "rockchip,rk3288-spdif", "rockchip,rk3066-spdif";
+ reg = <0xff8b0000 0x10000>;
+ #sound-dai-cells = <0>;
+ clock-names = "hclk", "mclk";
+ clocks = <&cru HCLK_SPDIF8CH>, <&cru SCLK_SPDIF8CH>;
+ dmas = <&dmac_bus_s 3>;
+ dma-names = "tx";
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx>;
+ rockchip,grf = <&grf>;
+ status = "disabled";
+ };
+
i2s: i2s@ff890000 {
compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s";
reg = <0xff890000 0x10000>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru ACLK_VOP0>, <&cru DCLK_VOP0>, <&cru HCLK_VOP0>;
clock-names = "aclk_vop", "dclk_vop", "hclk_vop";
+ power-domains = <&power RK3288_PD_VIO>;
resets = <&cru SRST_LCDC0_AXI>, <&cru SRST_LCDC0_AHB>, <&cru SRST_LCDC0_DCLK>;
reset-names = "axi", "ahb", "dclk";
iommus = <&vopb_mmu>;
reg = <0xff930300 0x100>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "vopb_mmu";
+ power-domains = <&power RK3288_PD_VIO>;
#iommu-cells = <0>;
status = "disabled";
};
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru ACLK_VOP1>, <&cru DCLK_VOP1>, <&cru HCLK_VOP1>;
clock-names = "aclk_vop", "dclk_vop", "hclk_vop";
+ power-domains = <&power RK3288_PD_VIO>;
resets = <&cru SRST_LCDC1_AXI>, <&cru SRST_LCDC1_AHB>, <&cru SRST_LCDC1_DCLK>;
reset-names = "axi", "ahb", "dclk";
iommus = <&vopl_mmu>;
reg = <0xff940300 0x100>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "vopl_mmu";
+ power-domains = <&power RK3288_PD_VIO>;
#iommu-cells = <0>;
status = "disabled";
};
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>;
clock-names = "iahb", "isfr";
+ power-domains = <&power RK3288_PD_VIO>;
status = "disabled";
ports {
#interrupt-cells = <2>;
};
+ hdmi {
+ hdmi_ddc: hdmi-ddc {
+ rockchip,pins = <7 19 RK_FUNC_2 &pcfg_pull_none>,
+ <7 20 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+
pcfg_pull_up: pcfg-pull-up {
bias-pull-up;
};
};
uart0_cts: uart0-cts {
- rockchip,pins = <4 18 RK_FUNC_1 &pcfg_pull_none>;
+ rockchip,pins = <4 18 RK_FUNC_1 &pcfg_pull_up>;
};
uart0_rts: uart0-rts {
};
uart1_cts: uart1-cts {
- rockchip,pins = <5 10 RK_FUNC_1 &pcfg_pull_none>;
+ rockchip,pins = <5 10 RK_FUNC_1 &pcfg_pull_up>;
};
uart1_rts: uart1-rts {
};
uart3_cts: uart3-cts {
- rockchip,pins = <7 9 RK_FUNC_1 &pcfg_pull_none>;
+ rockchip,pins = <7 9 RK_FUNC_1 &pcfg_pull_up>;
};
uart3_rts: uart3-rts {
};
uart4_cts: uart4-cts {
- rockchip,pins = <5 14 3 &pcfg_pull_none>;
+ rockchip,pins = <5 14 3 &pcfg_pull_up>;
};
uart4_rts: uart4-rts {
<4 3 3 &pcfg_pull_none>;
};
};
+
+ spdif {
+ spdif_tx: spdif-tx {
+ rockchip,pins = <RK_GPIO6 11 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
};
};
cache-level = <2>;
};
+ sdmmc0: sdio-host@a0000000 {
+ compatible = "atmel,sama5d2-sdhci";
+ reg = <0xa0000000 0x300>;
+ interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>;
+ clock-names = "hclock", "multclk", "baseclk";
+ status = "disabled";
+ };
+
+ sdmmc1: sdio-host@b0000000 {
+ compatible = "atmel,sama5d2-sdhci";
+ reg = <0xb0000000 0x300>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&sdmmc1_hclk>, <&sdmmc1_gclk>, <&main>;
+ clock-names = "hclock", "multclk", "baseclk";
+ status = "disabled";
+ };
+
apb {
compatible = "simple-bus";
#address-cells = <1>;
};
pmc: pmc@f0014000 {
- compatible = "atmel,sama5d2-pmc";
+ compatible = "atmel,sama5d2-pmc", "syscon";
reg = <0xf0014000 0x160>;
interrupts = <74 IRQ_TYPE_LEVEL_HIGH 7>;
interrupt-controller;
atmel,clk-output-range = <0 83000000>;
};
+ i2s0_clk: i2s0_clk {
+ #clock-cells = <0>;
+ reg = <54>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ i2s1_clk: i2s1_clk {
+ #clock-cells = <0>;
+ reg = <55>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
classd_clk: classd_clk {
#clock-cells = <0>;
reg = <59>;
reg = <53>;
};
};
+
+ gck {
+ compatible = "atmel,sama5d2-clk-generated";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&pmc>;
+ clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
+
+ sdmmc0_gclk: sdmmc0_gclk {
+ #clock-cells = <0>;
+ reg = <31>;
+ };
+
+ sdmmc1_gclk: sdmmc1_gclk {
+ #clock-cells = <0>;
+ reg = <32>;
+ };
+
+ tcb0_gclk: tcb0_gclk {
+ #clock-cells = <0>;
+ reg = <35>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ tcb1_gclk: tcb1_gclk {
+ #clock-cells = <0>;
+ reg = <36>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ pwm_gclk: pwm_gclk {
+ #clock-cells = <0>;
+ reg = <38>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ i2s0_gclk: i2s0_gclk {
+ #clock-cells = <0>;
+ reg = <54>;
+ };
+
+ i2s1_gclk: i2s1_gclk {
+ #clock-cells = <0>;
+ reg = <55>;
+ };
+ };
};
sha@f0028000 {
dma-names = "tx";
clocks = <&sha_clk>;
clock-names = "sha_clk";
- status = "disabled";
+ status = "okay";
};
aes@f002c000 {
dma-names = "tx", "rx";
clocks = <&aes_clk>;
clock-names = "aes_clk";
- status = "disabled";
+ status = "okay";
};
spi0: spi@f8000000 {
status = "disabled";
};
+ flx0: flexcom@f8034000 {
+ compatible = "atmel,sama5d2-flexcom";
+ reg = <0xf8034000 0x200>;
+ clocks = <&flx0_clk>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8034000 0x800>;
+ status = "disabled";
+ };
+
+ flx1: flexcom@f8038000 {
+ compatible = "atmel,sama5d2-flexcom";
+ reg = <0xf8038000 0x200>;
+ clocks = <&flx1_clk>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8038000 0x800>;
+ status = "disabled";
+ };
+
+ rstc@f8048000 {
+ compatible = "atmel,sama5d3-rstc";
+ reg = <0xf8048000 0x10>;
+ clocks = <&clk32k>;
+ };
+
pit: timer@f8048030 {
compatible = "atmel,at91sam9260-pit";
reg = <0xf8048030 0x10>;
status = "disabled";
};
+ flx2: flexcom@fc010000 {
+ compatible = "atmel,sama5d2-flexcom";
+ reg = <0xfc010000 0x200>;
+ clocks = <&flx2_clk>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xfc010000 0x800>;
+ status = "disabled";
+ };
+
+ flx3: flexcom@fc014000 {
+ compatible = "atmel,sama5d2-flexcom";
+ reg = <0xfc014000 0x200>;
+ clocks = <&flx3_clk>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xfc014000 0x800>;
+ status = "disabled";
+ };
+
+ flx4: flexcom@fc018000 {
+ compatible = "atmel,sama5d2-flexcom";
+ reg = <0xfc018000 0x200>;
+ clocks = <&flx4_clk>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xfc018000 0x800>;
+ status = "disabled";
+ };
+
aic: interrupt-controller@fc020000 {
#interrupt-cells = <3>;
compatible = "atmel,sama5d2-aic";
status = "disabled";
};
+ pioA: pinctrl@fc038000 {
+ compatible = "atmel,sama5d2-pinctrl";
+ reg = <0xfc038000 0x600>;
+ interrupts = <18 IRQ_TYPE_LEVEL_HIGH 7>,
+ <68 IRQ_TYPE_LEVEL_HIGH 7>,
+ <69 IRQ_TYPE_LEVEL_HIGH 7>,
+ <70 IRQ_TYPE_LEVEL_HIGH 7>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ clocks = <&pioA_clk>;
+ };
++
+ tdes@fc044000 {
+ compatible = "atmel,at91sam9g46-tdes";
+ reg = <0xfc044000 0x100>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(28))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(29))>;
+ dma-names = "tx", "rx";
+ clocks = <&tdes_clk>;
+ clock-names = "tdes_clk";
+ status = "okay";
+ };
};
};
};
<ST_IRQ_SYSCFG_DISABLED>;
};
+ /* Display */
+ vtg_main: sti-vtg-main@8d02800 {
+ compatible = "st,vtg";
+ reg = <0x8d02800 0x200>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_NONE>;
+ };
+
+ vtg_aux: sti-vtg-aux@8d00200 {
+ compatible = "st,vtg";
+ reg = <0x8d00200 0x100>;
+ interrupts = <GIC_SPI 109 IRQ_TYPE_NONE>;
+ };
+
serial@9830000 {
compatible = "st,asc";
reg = <0x9830000 0x2c>;
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
clock-names = "ssc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
status = "disabled";
};
interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
clock-names = "ssc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi2_default>;
status = "disabled";
};
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
clock-names = "ssc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi3_default>;
status = "disabled";
};
interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
clock-names = "ssc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi4_default>;
status = "disabled";
};
interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk_sysin>;
clock-names = "ssc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi10_default>;
status = "disabled";
};
interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk_sysin>;
clock-names = "ssc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi11_default>;
status = "disabled";
};
interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk_sysin>;
clock-names = "ssc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi12_default>;
status = "disabled";
};
/* COMMS PWM Module */
pwm0: pwm@9810000 {
compatible = "st,sti-pwm";
- status = "okay";
#pwm-cells = <2>;
reg = <0x9810000 0x68>;
pinctrl-names = "default";
clock-names = "pwm";
clocks = <&clk_sysin>;
st,pwm-num-chan = <1>;
+
+ status = "disabled";
};
/* SBC PWM Module */
pwm1: pwm@9510000 {
compatible = "st,sti-pwm";
- status = "okay";
#pwm-cells = <2>;
reg = <0x9510000 0x68>;
pinctrl-names = "default";
clock-names = "pwm";
clocks = <&clk_sysin>;
st,pwm-num-chan = <4>;
+
+ status = "disabled";
+ };
+
+ rng10: rng@08a89000 {
+ compatible = "st,rng";
+ reg = <0x08a89000 0x1000>;
+ clocks = <&clk_sysin>;
+ status = "okay";
+ };
+
+ rng11: rng@08a8a000 {
+ compatible = "st,rng";
+ reg = <0x08a8a000 0x1000>;
+ clocks = <&clk_sysin>;
+ status = "okay";
+ };
+
+ ethernet0: dwmac@9630000 {
+ device_type = "network";
+ status = "disabled";
+ compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ reg = <0x9630000 0x8000>, <0x80 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+
+ st,syscon = <&syscfg_sbc_reg 0x80>;
+ st,gmac_en;
+ resets = <&softreset STIH407_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
+
+ interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>,
+ <GIC_SPI 99 IRQ_TYPE_NONE>;
+ interrupt-names = "macirq", "eth_wake_irq";
+
+ /* DMA Bus Mode */
+ snps,pbl = <8>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii1>;
+
+ clock-names = "stmmaceth", "sti-ethclk";
+ clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>,
+ <&clk_s_c0_flexgen CLK_ETH_PHY>;
};
+
+ rng10: rng@08a89000 {
+ compatible = "st,rng";
+ reg = <0x08a89000 0x1000>;
+ clocks = <&clk_sysin>;
+ status = "okay";
+ };
+
+ rng11: rng@08a8a000 {
+ compatible = "st,rng";
+ reg = <0x08a8a000 0x1000>;
+ clocks = <&clk_sysin>;
+ status = "okay";
+ };
};
};
gpio-controller;
#interrupt-cells = <2>;
interrupt-controller;
+ /*
gpio-ranges = <&pinmux 0 0 251>;
+ */
};
apbdma: dma@0,60020000 {
sata@0,70020000 {
compatible = "nvidia,tegra124-ahci";
-
reg = <0x0 0x70027000 0x0 0x2000>, /* AHCI */
- <0x0 0x70020000 0x0 0x7000>; /* SATA */
-
+ <0x0 0x70020000 0x0 0x7000>; /* SATA */
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
-
clocks = <&tegra_car TEGRA124_CLK_SATA>,
- <&tegra_car TEGRA124_CLK_SATA_OOB>,
- <&tegra_car TEGRA124_CLK_CML1>,
- <&tegra_car TEGRA124_CLK_PLL_E>;
+ <&tegra_car TEGRA124_CLK_SATA_OOB>,
+ <&tegra_car TEGRA124_CLK_CML1>,
+ <&tegra_car TEGRA124_CLK_PLL_E>;
clock-names = "sata", "sata-oob", "cml1", "pll_e";
-
resets = <&tegra_car 124>,
- <&tegra_car 123>,
- <&tegra_car 129>;
+ <&tegra_car 123>,
+ <&tegra_car 129>;
reset-names = "sata", "sata-oob", "sata-cold";
-
phys = <&padctl TEGRA_XUSB_PADCTL_SATA>;
phy-names = "sata-phy";
-
status = "disabled";
};
reg = <0x0 0x70030000 0x0 0x10000>;
interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&tegra_car TEGRA124_CLK_HDA>,
- <&tegra_car TEGRA124_CLK_HDA2HDMI>,
+ <&tegra_car TEGRA124_CLK_HDA2HDMI>,
<&tegra_car TEGRA124_CLK_HDA2CODEC_2X>;
clock-names = "hda", "hda2hdmi", "hda2codec_2x";
resets = <&tegra_car 125>, /* hda */
gpio-controller;
#interrupt-cells = <2>;
interrupt-controller;
+ /*
gpio-ranges = <&pinmux 0 0 224>;
+ */
};
apbmisc@70000800 {
<&tegra_car TEGRA20_CLK_PLL_E>;
clock-names = "pex", "afi", "pll_e";
resets = <&tegra_car 70>,
- <&tegra_car 72>,
- <&tegra_car 74>;
+ <&tegra_car 72>,
+ <&tegra_car 74>;
reset-names = "pex", "afi", "pcie_x";
status = "disabled";
<&tegra_car TEGRA30_CLK_CML0>;
clock-names = "pex", "afi", "pll_e", "cml";
resets = <&tegra_car 70>,
- <&tegra_car 72>,
- <&tegra_car 74>;
+ <&tegra_car 72>,
+ <&tegra_car 74>;
reset-names = "pex", "afi", "pcie_x";
status = "disabled";
&tegra_car TEGRA30_CLK_GR3D2>;
clock-names = "3d", "3d2";
resets = <&tegra_car 24>,
- <&tegra_car 98>;
+ <&tegra_car 98>;
reset-names = "3d", "3d2";
};
gpio-controller;
#interrupt-cells = <2>;
interrupt-controller;
+ /*
gpio-ranges = <&pinmux 0 0 248>;
+ */
};
apbmisc@70000800 {
};
i2c@7000c000 {
- compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+ compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
reg = <0x7000c000 0x100>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
reg = <0x70030000 0x10000>;
interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&tegra_car TEGRA30_CLK_HDA>,
- <&tegra_car TEGRA30_CLK_HDA2HDMI>,
+ <&tegra_car TEGRA30_CLK_HDA2HDMI>,
<&tegra_car TEGRA30_CLK_HDA2CODEC_2X>;
clock-names = "hda", "hda2hdmi", "hda2codec_2x";
resets = <&tegra_car 125>, /* hda */
};
chosen {
- bootargs = "console=ttyS0,115200";
- stdout-path = &serial0;
+ stdout-path = "serial0:115200n8";
};
aliases {
};
&extbus {
- ranges = <0 0x00000000 0x0f000000 0x01000000
- 1 0x00000000 0x00000000 0x08000000>;
+ ranges = <1 0x00000000 0x42000000 0x02000000>;
};
&support_card {
- ranges = <0x00000000 1 0x03f00000 0x00100000>;
+ ranges = <0x00000000 1 0x01f00000 0x00100000>;
};
ðsc {
- interrupts = <0 50 4>;
+ interrupts = <0 52 4>;
};
&serial0 {
config ARCH_BERLIN
bool "Marvell Berlin SoC Family"
+ select ARCH_REQUIRE_GPIOLIB
select DW_APB_ICTL
help
This enables support for Marvell Berlin SoC Family
help
This enables support for Samsung Exynos7 SoC family
- config ARCH_FSL_LS2085A
- bool "Freescale LS2085A SOC"
+ config ARCH_LAYERSCAPE
+ bool "ARMv8 based Freescale Layerscape SoC family"
help
- This enables support for Freescale LS2085A SOC.
+ This enables support for the Freescale Layerscape SoC family.
config ARCH_HISI
bool "Hisilicon SoC Family"
help
This enables support for AMD Seattle SOC Family
+ config ARCH_STRATIX10
+ bool "Altera's Stratix 10 SoCFPGA Family"
+ help
+ This enables support for Altera's Stratix 10 SoCFPGA Family.
+
config ARCH_TEGRA
bool "NVIDIA Tegra SoC Family"
select ARCH_HAS_RESET_CONTROLLER
+ dts-dirs += altera
dts-dirs += amd
dts-dirs += apm
dts-dirs += arm
dts-dirs += xilinx
subdir-y := $(dts-dirs)
+
+dtstree := $(srctree)/$(src)
+
+dtb-$(CONFIG_OF_ALL_DTBS) := $(patsubst $(dtstree)/%.dts,%.dtb, $(foreach d,$(dts-dirs), $(wildcard $(dtstree)/$(d)/*.dts)))
+
+always := $(dtb-y)
clock-frequency = <50000000>;
};
+ pmu {
+ compatible = "apm,potenza-pmu", "arm,armv8-pmuv3";
+ interrupts = <1 12 0xff04>;
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <2>;
clock-output-names = "xge0clk";
};
+ xge1clk: xge1clk@1f62c000 {
+ compatible = "apm,xgene-device-clock";
+ status = "disabled";
+ #clock-cells = <1>;
+ clocks = <&socplldiv2 0>;
+ reg = <0x0 0x1f62c000 0x0 0x1000>;
+ reg-names = "csr-reg";
+ csr-mask = <0x3>;
+ clock-output-names = "xge1clk";
+ };
+
sataphy1clk: sataphy1clk@1f21c000 {
compatible = "apm,xgene-device-clock";
#clock-cells = <1>;
0x0 0x1f 0x4>;
};
+ scu: system-clk-controller@17000000 {
+ compatible = "apm,xgene-scu","syscon";
+ reg = <0x0 0x17000000 0x0 0x400>;
+ };
+
+ reboot: reboot@17000014 {
+ compatible = "syscon-reboot";
+ regmap = <&scu>;
+ offset = <0x14>;
+ mask = <0x1>;
+ };
+
csw: csw@7e200000 {
compatible = "apm,xgene-csw", "syscon";
reg = <0x0 0x7e200000 0x0 0x1000>;
reg = <0x0 0x7c600000 0x0 0x200000>;
pmd-controller = <3>;
};
+
+ edacl3@7e600000 {
+ compatible = "apm,xgene-edac-l3";
+ reg = <0x0 0x7e600000 0x0 0x1000>;
+ };
+
+ edacsoc@7e930000 {
+ compatible = "apm,xgene-edac-soc-v1";
+ reg = <0x0 0x7e930000 0x0 0x1000>;
+ };
};
pcie0: pcie@1f2b0000 {
phy-connection-type = "xgmii";
};
+ xgenet1: ethernet@1f620000 {
+ compatible = "apm,xgene1-xgenet";
+ status = "disabled";
+ reg = <0x0 0x1f620000 0x0 0xd100>,
+ <0x0 0x1f600000 0x0 0Xc300>,
+ <0x0 0x18000000 0x0 0X8000>;
+ reg-names = "enet_csr", "ring_csr", "ring_cmd";
+ interrupts = <0x0 0x6C 0x4>,
+ <0x0 0x6D 0x4>;
+ port-id = <1>;
+ dma-coherent;
+ clocks = <&xge1clk 0>;
+ /* mac address will be overwritten by the bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ phy-connection-type = "xgmii";
+ };
+
rng: rng@10520000 {
compatible = "apm,xgene-rng";
reg = <0x0 0x10520000 0x0 0x100>;
button@1 {
debounce_interval = <50>;
- wakeup = <1>;
+ wakeup-source;
linux,code = <116>;
label = "POWER";
gpios = <&iofpga_gpio0 0 0x4>;
};
button@2 {
debounce_interval = <50>;
- wakeup = <1>;
+ wakeup-source;
linux,code = <102>;
label = "HOME";
gpios = <&iofpga_gpio0 1 0x4>;
};
button@3 {
debounce_interval = <50>;
- wakeup = <1>;
+ wakeup-source;
linux,code = <152>;
label = "RLOCK";
gpios = <&iofpga_gpio0 2 0x4>;
};
button@4 {
debounce_interval = <50>;
- wakeup = <1>;
+ wakeup-source;
linux,code = <115>;
label = "VOL+";
gpios = <&iofpga_gpio0 3 0x4>;
};
button@5 {
debounce_interval = <50>;
- wakeup = <1>;
+ wakeup-source;
linux,code = <114>;
label = "VOL-";
gpios = <&iofpga_gpio0 4 0x4>;
};
button@6 {
debounce_interval = <50>;
- wakeup = <1>;
+ wakeup-source;
linux,code = <99>;
label = "NMI";
gpios = <&iofpga_gpio0 5 0x4>;
};
};
+ flash@0,00000000 {
+ /* 2 * 32MiB NOR Flash memory mounted on CS0 */
+ compatible = "arm,vexpress-flash", "cfi-flash";
+ linux,part-probe = "afs";
+ reg = <0 0x00000000 0x04000000>;
+ bank-width = <4>;
+ /*
+ * Unfortunately, accessing the flash disturbs
+ * the CPU idle states (suspend) and CPU
+ * hotplug of the platform. For this reason,
+ * flash hardware access is disabled by default.
+ */
+ status = "disabled";
+ };
+
ethernet@2,00000000 {
compatible = "smsc,lan9118", "smsc,lan9115";
reg = <2 0x00000000 0x10000>;
#address-cells = <2>;
#size-cells = <0>;
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&A57_0>;
+ };
+ core1 {
+ cpu = <&A57_1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&A53_0>;
+ };
+ core1 {
+ cpu = <&A53_1>;
+ };
+ core2 {
+ cpu = <&A53_2>;
+ };
+ core3 {
+ cpu = <&A53_3>;
+ };
+ };
+ };
+
A57_0: cpu@0 {
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x0 0x0>;
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A57_L2>;
+ clocks = <&scpi_dvfs 0>;
};
A57_1: cpu@1 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A57_L2>;
+ clocks = <&scpi_dvfs 0>;
};
A53_0: cpu@100 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ clocks = <&scpi_dvfs 1>;
};
A53_1: cpu@101 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ clocks = <&scpi_dvfs 1>;
};
A53_2: cpu@102 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ clocks = <&scpi_dvfs 1>;
};
A53_3: cpu@103 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ clocks = <&scpi_dvfs 1>;
};
A57_L2: l2-cache0 {
};
};
- pmu {
- compatible = "arm,armv8-pmuv3";
+ pmu_a57 {
+ compatible = "arm,cortex-a57-pmu";
interrupts = <GIC_SPI 02 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 06 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 06 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&A57_0>,
+ <&A57_1>;
+ };
+
+ pmu_a53 {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-affinity = <&A57_0>,
- <&A57_1>,
- <&A53_0>,
+ interrupt-affinity = <&A53_0>,
<&A53_1>,
<&A53_2>,
<&A53_3>;
#include "juno-base.dtsi"
+ pcie-controller@40000000 {
+ compatible = "arm,juno-r1-pcie", "plda,xpressrich3-axi", "pci-host-ecam-generic";
+ device_type = "pci";
+ reg = <0 0x40000000 0 0x10000000>; /* ECAM config space */
+ bus-range = <0 255>;
+ linux,pci-domain = <0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ dma-coherent;
+ ranges = <0x01000000 0x00 0x5f800000 0x00 0x5f800000 0x0 0x00800000>,
+ <0x02000000 0x00 0x50000000 0x00 0x50000000 0x0 0x08000000>,
+ <0x42000000 0x40 0x00000000 0x40 0x00000000 0x1 0x00000000>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &gic 0 0 0 136 4>,
+ <0 0 0 2 &gic 0 0 0 137 4>,
+ <0 0 0 3 &gic 0 0 0 138 4>,
+ <0 0 0 4 &gic 0 0 0 139 4>;
+ msi-parent = <&v2m_0>;
+ };
};
&memtimer {
#address-cells = <2>;
#size-cells = <0>;
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&A57_0>;
+ };
+ core1 {
+ cpu = <&A57_1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&A53_0>;
+ };
+ core1 {
+ cpu = <&A53_1>;
+ };
+ core2 {
+ cpu = <&A53_2>;
+ };
+ core3 {
+ cpu = <&A53_3>;
+ };
+ };
+ };
+
A57_0: cpu@0 {
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x0 0x0>;
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A57_L2>;
+ clocks = <&scpi_dvfs 0>;
};
A57_1: cpu@1 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A57_L2>;
+ clocks = <&scpi_dvfs 0>;
};
A53_0: cpu@100 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ clocks = <&scpi_dvfs 1>;
};
A53_1: cpu@101 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ clocks = <&scpi_dvfs 1>;
};
A53_2: cpu@102 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ clocks = <&scpi_dvfs 1>;
};
A53_3: cpu@103 {
device_type = "cpu";
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ clocks = <&scpi_dvfs 1>;
};
A57_L2: l2-cache0 {
};
};
- pmu {
- compatible = "arm,armv8-pmuv3";
+ pmu_a57 {
+ compatible = "arm,cortex-a57-pmu";
interrupts = <GIC_SPI 02 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 06 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 06 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&A57_0>,
+ <&A57_1>;
+ };
+
+ pmu_a53 {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-affinity = <&A57_0>,
- <&A57_1>,
- <&A53_0>,
+ interrupt-affinity = <&A53_0>,
<&A53_1>,
<&A53_2>,
<&A53_3>;
CONFIG_ARCH_BCM_IPROC=y
CONFIG_ARCH_BERLIN=y
CONFIG_ARCH_EXYNOS7=y
- CONFIG_ARCH_FSL_LS2085A=y
+ CONFIG_ARCH_LAYERSCAPE=y
CONFIG_ARCH_HISI=y
CONFIG_ARCH_MEDIATEK=y
CONFIG_ARCH_ROCKCHIP=y
CONFIG_ARCH_SEATTLE=y
+ CONFIG_ARCH_STRATIX10=y
CONFIG_ARCH_TEGRA=y
CONFIG_ARCH_TEGRA_132_SOC=y
CONFIG_ARCH_QCOM=y
CONFIG_ARCH_ZYNQMP=y
CONFIG_PCI=y
CONFIG_PCI_MSI=y
+ CONFIG_PCI_HOST_GENERIC=y
CONFIG_PCI_XGENE=y
CONFIG_SMP=y
+CONFIG_SCHED_MC=y
CONFIG_PREEMPT=y
CONFIG_KSM=y
CONFIG_TRANSPARENT_HUGEPAGE=y
CONFIG_SERIAL_8250_MT6577=y
CONFIG_SERIAL_AMBA_PL011=y
CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_SAMSUNG=y
+CONFIG_SERIAL_SAMSUNG_UARTS_4=y
+CONFIG_SERIAL_SAMSUNG_UARTS=4
+CONFIG_SERIAL_SAMSUNG_CONSOLE=y
CONFIG_SERIAL_MSM=y
CONFIG_SERIAL_MSM_CONSOLE=y
CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_PLTFM=y
CONFIG_MMC_SPI=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_IDMAC=y
+CONFIG_MMC_DW_PLTFM=y
+CONFIG_MMC_DW_EXYNOS=y
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_SYSCON=y
projects / firefly-linux-kernel-4.4.55.git / commitdiff