That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit
aa2f4b16f830 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Change-Id: I0c5843d4da7ab9ed975a723075b4b31b6c2fcc54
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Wu Liang feng <wulf@rock-chips.com>
(cherry picked from commit
bc5081617faeb3b2f0c126dc37264b87af7da47f)
the second element is expected to be a handle to the USB3/SS PHY
- phys: from the *Generic PHY* bindings
- phy-names: from the *Generic PHY* bindings
- - tx-fifo-resize: determines if the FIFO *has* to be reallocated.
- snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
- snps,disable_scramble_quirk: true when SW should disable data scrambling.
Only really useful for FPGA builds.
register for post-silicon frame length adjustment when the
fladj_30mhz_sdbnd signal is invalid or incorrect.
+ - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
+
This is usually a subnode to DWC3 glue to which it is connected.
dwc3@4a030000 {
reg = <0x4a030000 0xcfff>;
interrupts = <0 92 4>
usb-phy = <&usb2_phy>, <&usb3,phy>;
- tx-fifo-resize;
};
interrupts = <0 205 0x4>;
phys = <&hs_phy>, <&ss_phy>;
phy-names = "usb2-phy", "usb3-phy";
- tx-fifo-resize;
dr_mode = "host";
};
};
dwc->usb3_lpm_capable = device_property_read_bool(dev,
"snps,usb3_lpm_capable");
- dwc->needs_fifo_resize = device_property_read_bool(dev,
- "tx-fifo-resize");
-
dwc->disable_scramble_quirk = device_property_read_bool(dev,
"snps,disable_scramble_quirk");
dwc->u2exit_lfps_quirk = device_property_read_bool(dev,
if (pdata->hird_threshold)
hird_threshold = pdata->hird_threshold;
- dwc->needs_fifo_resize = pdata->tx_fifo_resize;
dwc->usb3_lpm_capable = pdata->usb3_lpm_capable;
dwc->dr_mode = pdata->dr_mode;
* 0 - utmi_sleep_n
* 1 - utmi_l1_suspend_n
* @is_fpga: true when we are using the FPGA board
- * @needs_fifo_resize: not all users might want fifo resizing, flag it
* @pullups_connected: true when Run/Stop bit is set
- * @resize_fifos: tells us it's ok to reconfigure our TxFIFO sizes.
* @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround
* @start_config_issued: true when StartConfig command has been issued
* @three_stage_setup: set if we perform a three phase setup
unsigned has_lpm_erratum:1;
unsigned is_utmi_l1_suspend:1;
unsigned is_fpga:1;
- unsigned needs_fifo_resize:1;
unsigned pullups_connected:1;
- unsigned resize_fifos:1;
unsigned setup_packet_pending:1;
unsigned three_stage_setup:1;
unsigned usb3_lpm_capable:1;
/* prototypes */
void dwc3_set_mode(struct dwc3 *dwc, u32 mode);
-int dwc3_gadget_resize_tx_fifos(struct dwc3 *dwc);
/* check whether we are on the DWC_usb31 core */
static inline bool dwc3_is_usb31(struct dwc3 *dwc)
reg = dwc3_readl(dwc->regs, DWC3_DCTL);
reg |= (DWC3_DCTL_ACCEPTU1ENA | DWC3_DCTL_ACCEPTU2ENA);
dwc3_writel(dwc->regs, DWC3_DCTL, reg);
-
- dwc->resize_fifos = true;
- dwc3_trace(trace_dwc3_ep0, "resize FIFOs flag SET");
}
break;
static void __dwc3_ep0_do_control_status(struct dwc3 *dwc, struct dwc3_ep *dep)
{
- if (dwc->resize_fifos) {
- dwc3_trace(trace_dwc3_ep0, "Resizing FIFOs");
- dwc3_gadget_resize_tx_fifos(dwc);
- dwc->resize_fifos = 0;
- }
-
WARN_ON(dwc3_ep0_start_control_status(dep));
}
return -ETIMEDOUT;
}
-/**
- * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case
- * @dwc: pointer to our context structure
- *
- * This function will a best effort FIFO allocation in order
- * to improve FIFO usage and throughput, while still allowing
- * us to enable as many endpoints as possible.
- *
- * Keep in mind that this operation will be highly dependent
- * on the configured size for RAM1 - which contains TxFifo -,
- * the amount of endpoints enabled on coreConsultant tool, and
- * the width of the Master Bus.
- *
- * In the ideal world, we would always be able to satisfy the
- * following equation:
- *
- * ((512 + 2 * MDWIDTH-Bytes) + (Number of IN Endpoints - 1) * \
- * (3 * (1024 + MDWIDTH-Bytes) + MDWIDTH-Bytes)) / MDWIDTH-Bytes
- *
- * Unfortunately, due to many variables that's not always the case.
- */
-int dwc3_gadget_resize_tx_fifos(struct dwc3 *dwc)
-{
- int last_fifo_depth = 0;
- int ram1_depth;
- int fifo_size;
- int mdwidth;
- int num;
-
- if (!dwc->needs_fifo_resize)
- return 0;
-
- ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
- mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0);
-
- /* MDWIDTH is represented in bits, we need it in bytes */
- mdwidth >>= 3;
-
- /*
- * FIXME For now we will only allocate 1 wMaxPacketSize space
- * for each enabled endpoint, later patches will come to
- * improve this algorithm so that we better use the internal
- * FIFO space
- */
- for (num = 0; num < dwc->num_in_eps; num++) {
- /* bit0 indicates direction; 1 means IN ep */
- struct dwc3_ep *dep = dwc->eps[(num << 1) | 1];
- int mult = 1;
- int tmp;
-
- if (!(dep->flags & DWC3_EP_ENABLED))
- continue;
-
- if (usb_endpoint_xfer_bulk(dep->endpoint.desc)
- || usb_endpoint_xfer_isoc(dep->endpoint.desc))
- mult = 3;
-
- /*
- * REVISIT: the following assumes we will always have enough
- * space available on the FIFO RAM for all possible use cases.
- * Make sure that's true somehow and change FIFO allocation
- * accordingly.
- *
- * If we have Bulk or Isochronous endpoints, we want
- * them to be able to be very, very fast. So we're giving
- * those endpoints a fifo_size which is enough for 3 full
- * packets
- */
- tmp = mult * (dep->endpoint.maxpacket + mdwidth);
- tmp += mdwidth;
-
- fifo_size = DIV_ROUND_UP(tmp, mdwidth);
-
- fifo_size |= (last_fifo_depth << 16);
-
- dwc3_trace(trace_dwc3_gadget, "%s: Fifo Addr %04x Size %d",
- dep->name, last_fifo_depth, fifo_size & 0xffff);
-
- dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(num), fifo_size);
-
- last_fifo_depth += (fifo_size & 0xffff);
- }
-
- return 0;
-}
-
void dwc3_gadget_giveback(struct dwc3_ep *dep, struct dwc3_request *req,
int status)
{
struct dwc3_platform_data {
enum usb_device_speed maximum_speed;
enum usb_dr_mode dr_mode;
- bool tx_fifo_resize;
bool usb3_lpm_capable;
unsigned is_utmi_l1_suspend:1;
projects / firefly-linux-kernel-4.4.55.git / commitdiff