usb: dwc3: rockchip: fix possible circular deadlock
[firefly-linux-kernel-4.4.55.git] / drivers / gpio / gpio-adp5588.c
1 /*
2  * GPIO Chip driver for Analog Devices
3  * ADP5588/ADP5587 I/O Expander and QWERTY Keypad Controller
4  *
5  * Copyright 2009-2010 Analog Devices Inc.
6  *
7  * Licensed under the GPL-2 or later.
8  */
9
10 #include <linux/module.h>
11 #include <linux/kernel.h>
12 #include <linux/slab.h>
13 #include <linux/init.h>
14 #include <linux/i2c.h>
15 #include <linux/gpio.h>
16 #include <linux/interrupt.h>
17 #include <linux/irq.h>
18
19 #include <linux/i2c/adp5588.h>
20
21 #define DRV_NAME        "adp5588-gpio"
22
23 /*
24  * Early pre 4.0 Silicon required to delay readout by at least 25ms,
25  * since the Event Counter Register updated 25ms after the interrupt
26  * asserted.
27  */
28 #define WA_DELAYED_READOUT_REVID(rev)   ((rev) < 4)
29
30 struct adp5588_gpio {
31         struct i2c_client *client;
32         struct gpio_chip gpio_chip;
33         struct mutex lock;      /* protect cached dir, dat_out */
34         /* protect serialized access to the interrupt controller bus */
35         struct mutex irq_lock;
36         unsigned gpio_start;
37         unsigned irq_base;
38         uint8_t dat_out[3];
39         uint8_t dir[3];
40         uint8_t int_lvl[3];
41         uint8_t int_en[3];
42         uint8_t irq_mask[3];
43         uint8_t irq_stat[3];
44 };
45
46 static int adp5588_gpio_read(struct i2c_client *client, u8 reg)
47 {
48         int ret = i2c_smbus_read_byte_data(client, reg);
49
50         if (ret < 0)
51                 dev_err(&client->dev, "Read Error\n");
52
53         return ret;
54 }
55
56 static int adp5588_gpio_write(struct i2c_client *client, u8 reg, u8 val)
57 {
58         int ret = i2c_smbus_write_byte_data(client, reg, val);
59
60         if (ret < 0)
61                 dev_err(&client->dev, "Write Error\n");
62
63         return ret;
64 }
65
66 static int adp5588_gpio_get_value(struct gpio_chip *chip, unsigned off)
67 {
68         struct adp5588_gpio *dev =
69             container_of(chip, struct adp5588_gpio, gpio_chip);
70         unsigned bank = ADP5588_BANK(off);
71         unsigned bit = ADP5588_BIT(off);
72         int val;
73
74         mutex_lock(&dev->lock);
75
76         if (dev->dir[bank] & bit)
77                 val = dev->dat_out[bank];
78         else
79                 val = adp5588_gpio_read(dev->client, GPIO_DAT_STAT1 + bank);
80
81         mutex_unlock(&dev->lock);
82
83         return !!(val & bit);
84 }
85
86 static void adp5588_gpio_set_value(struct gpio_chip *chip,
87                                    unsigned off, int val)
88 {
89         unsigned bank, bit;
90         struct adp5588_gpio *dev =
91             container_of(chip, struct adp5588_gpio, gpio_chip);
92
93         bank = ADP5588_BANK(off);
94         bit = ADP5588_BIT(off);
95
96         mutex_lock(&dev->lock);
97         if (val)
98                 dev->dat_out[bank] |= bit;
99         else
100                 dev->dat_out[bank] &= ~bit;
101
102         adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank,
103                            dev->dat_out[bank]);
104         mutex_unlock(&dev->lock);
105 }
106
107 static int adp5588_gpio_direction_input(struct gpio_chip *chip, unsigned off)
108 {
109         int ret;
110         unsigned bank;
111         struct adp5588_gpio *dev =
112             container_of(chip, struct adp5588_gpio, gpio_chip);
113
114         bank = ADP5588_BANK(off);
115
116         mutex_lock(&dev->lock);
117         dev->dir[bank] &= ~ADP5588_BIT(off);
118         ret = adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, dev->dir[bank]);
119         mutex_unlock(&dev->lock);
120
121         return ret;
122 }
123
124 static int adp5588_gpio_direction_output(struct gpio_chip *chip,
125                                          unsigned off, int val)
126 {
127         int ret;
128         unsigned bank, bit;
129         struct adp5588_gpio *dev =
130             container_of(chip, struct adp5588_gpio, gpio_chip);
131
132         bank = ADP5588_BANK(off);
133         bit = ADP5588_BIT(off);
134
135         mutex_lock(&dev->lock);
136         dev->dir[bank] |= bit;
137
138         if (val)
139                 dev->dat_out[bank] |= bit;
140         else
141                 dev->dat_out[bank] &= ~bit;
142
143         ret = adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank,
144                                  dev->dat_out[bank]);
145         ret |= adp5588_gpio_write(dev->client, GPIO_DIR1 + bank,
146                                  dev->dir[bank]);
147         mutex_unlock(&dev->lock);
148
149         return ret;
150 }
151
152 #ifdef CONFIG_GPIO_ADP5588_IRQ
153 static int adp5588_gpio_to_irq(struct gpio_chip *chip, unsigned off)
154 {
155         struct adp5588_gpio *dev =
156                 container_of(chip, struct adp5588_gpio, gpio_chip);
157         return dev->irq_base + off;
158 }
159
160 static void adp5588_irq_bus_lock(struct irq_data *d)
161 {
162         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
163
164         mutex_lock(&dev->irq_lock);
165 }
166
167  /*
168   * genirq core code can issue chip->mask/unmask from atomic context.
169   * This doesn't work for slow busses where an access needs to sleep.
170   * bus_sync_unlock() is therefore called outside the atomic context,
171   * syncs the current irq mask state with the slow external controller
172   * and unlocks the bus.
173   */
174
175 static void adp5588_irq_bus_sync_unlock(struct irq_data *d)
176 {
177         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
178         int i;
179
180         for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++)
181                 if (dev->int_en[i] ^ dev->irq_mask[i]) {
182                         dev->int_en[i] = dev->irq_mask[i];
183                         adp5588_gpio_write(dev->client, GPIO_INT_EN1 + i,
184                                            dev->int_en[i]);
185                 }
186
187         mutex_unlock(&dev->irq_lock);
188 }
189
190 static void adp5588_irq_mask(struct irq_data *d)
191 {
192         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
193         unsigned gpio = d->irq - dev->irq_base;
194
195         dev->irq_mask[ADP5588_BANK(gpio)] &= ~ADP5588_BIT(gpio);
196 }
197
198 static void adp5588_irq_unmask(struct irq_data *d)
199 {
200         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
201         unsigned gpio = d->irq - dev->irq_base;
202
203         dev->irq_mask[ADP5588_BANK(gpio)] |= ADP5588_BIT(gpio);
204 }
205
206 static int adp5588_irq_set_type(struct irq_data *d, unsigned int type)
207 {
208         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
209         uint16_t gpio = d->irq - dev->irq_base;
210         unsigned bank, bit;
211
212         if ((type & IRQ_TYPE_EDGE_BOTH)) {
213                 dev_err(&dev->client->dev, "irq %d: unsupported type %d\n",
214                         d->irq, type);
215                 return -EINVAL;
216         }
217
218         bank = ADP5588_BANK(gpio);
219         bit = ADP5588_BIT(gpio);
220
221         if (type & IRQ_TYPE_LEVEL_HIGH)
222                 dev->int_lvl[bank] |= bit;
223         else if (type & IRQ_TYPE_LEVEL_LOW)
224                 dev->int_lvl[bank] &= ~bit;
225         else
226                 return -EINVAL;
227
228         adp5588_gpio_direction_input(&dev->gpio_chip, gpio);
229         adp5588_gpio_write(dev->client, GPIO_INT_LVL1 + bank,
230                            dev->int_lvl[bank]);
231
232         return 0;
233 }
234
235 static struct irq_chip adp5588_irq_chip = {
236         .name                   = "adp5588",
237         .irq_mask               = adp5588_irq_mask,
238         .irq_unmask             = adp5588_irq_unmask,
239         .irq_bus_lock           = adp5588_irq_bus_lock,
240         .irq_bus_sync_unlock    = adp5588_irq_bus_sync_unlock,
241         .irq_set_type           = adp5588_irq_set_type,
242 };
243
244 static int adp5588_gpio_read_intstat(struct i2c_client *client, u8 *buf)
245 {
246         int ret = i2c_smbus_read_i2c_block_data(client, GPIO_INT_STAT1, 3, buf);
247
248         if (ret < 0)
249                 dev_err(&client->dev, "Read INT_STAT Error\n");
250
251         return ret;
252 }
253
254 static irqreturn_t adp5588_irq_handler(int irq, void *devid)
255 {
256         struct adp5588_gpio *dev = devid;
257         unsigned status, bank, bit, pending;
258         int ret;
259         status = adp5588_gpio_read(dev->client, INT_STAT);
260
261         if (status & ADP5588_GPI_INT) {
262                 ret = adp5588_gpio_read_intstat(dev->client, dev->irq_stat);
263                 if (ret < 0)
264                         memset(dev->irq_stat, 0, ARRAY_SIZE(dev->irq_stat));
265
266                 for (bank = 0, bit = 0; bank <= ADP5588_BANK(ADP5588_MAXGPIO);
267                         bank++, bit = 0) {
268                         pending = dev->irq_stat[bank] & dev->irq_mask[bank];
269
270                         while (pending) {
271                                 if (pending & (1 << bit)) {
272                                         handle_nested_irq(dev->irq_base +
273                                                           (bank << 3) + bit);
274                                         pending &= ~(1 << bit);
275
276                                 }
277                                 bit++;
278                         }
279                 }
280         }
281
282         adp5588_gpio_write(dev->client, INT_STAT, status); /* Status is W1C */
283
284         return IRQ_HANDLED;
285 }
286
287 static int adp5588_irq_setup(struct adp5588_gpio *dev)
288 {
289         struct i2c_client *client = dev->client;
290         struct adp5588_gpio_platform_data *pdata =
291                         dev_get_platdata(&client->dev);
292         unsigned gpio;
293         int ret;
294
295         adp5588_gpio_write(client, CFG, ADP5588_AUTO_INC);
296         adp5588_gpio_write(client, INT_STAT, -1); /* status is W1C */
297         adp5588_gpio_read_intstat(client, dev->irq_stat); /* read to clear */
298
299         dev->irq_base = pdata->irq_base;
300         mutex_init(&dev->irq_lock);
301
302         for (gpio = 0; gpio < dev->gpio_chip.ngpio; gpio++) {
303                 int irq = gpio + dev->irq_base;
304                 irq_set_chip_data(irq, dev);
305                 irq_set_chip_and_handler(irq, &adp5588_irq_chip,
306                                          handle_level_irq);
307                 irq_set_nested_thread(irq, 1);
308                 irq_modify_status(irq, IRQ_NOREQUEST, IRQ_NOPROBE);
309         }
310
311         ret = request_threaded_irq(client->irq,
312                                    NULL,
313                                    adp5588_irq_handler,
314                                    IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
315                                    dev_name(&client->dev), dev);
316         if (ret) {
317                 dev_err(&client->dev, "failed to request irq %d\n",
318                         client->irq);
319                 goto out;
320         }
321
322         dev->gpio_chip.to_irq = adp5588_gpio_to_irq;
323         adp5588_gpio_write(client, CFG,
324                 ADP5588_AUTO_INC | ADP5588_INT_CFG | ADP5588_GPI_INT);
325
326         return 0;
327
328 out:
329         dev->irq_base = 0;
330         return ret;
331 }
332
333 static void adp5588_irq_teardown(struct adp5588_gpio *dev)
334 {
335         if (dev->irq_base)
336                 free_irq(dev->client->irq, dev);
337 }
338
339 #else
340 static int adp5588_irq_setup(struct adp5588_gpio *dev)
341 {
342         struct i2c_client *client = dev->client;
343         dev_warn(&client->dev, "interrupt support not compiled in\n");
344
345         return 0;
346 }
347
348 static void adp5588_irq_teardown(struct adp5588_gpio *dev)
349 {
350 }
351 #endif /* CONFIG_GPIO_ADP5588_IRQ */
352
353 static int adp5588_gpio_probe(struct i2c_client *client,
354                                         const struct i2c_device_id *id)
355 {
356         struct adp5588_gpio_platform_data *pdata =
357                         dev_get_platdata(&client->dev);
358         struct adp5588_gpio *dev;
359         struct gpio_chip *gc;
360         int ret, i, revid;
361
362         if (!pdata) {
363                 dev_err(&client->dev, "missing platform data\n");
364                 return -ENODEV;
365         }
366
367         if (!i2c_check_functionality(client->adapter,
368                                         I2C_FUNC_SMBUS_BYTE_DATA)) {
369                 dev_err(&client->dev, "SMBUS Byte Data not Supported\n");
370                 return -EIO;
371         }
372
373         dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL);
374         if (!dev)
375                 return -ENOMEM;
376
377         dev->client = client;
378
379         gc = &dev->gpio_chip;
380         gc->direction_input = adp5588_gpio_direction_input;
381         gc->direction_output = adp5588_gpio_direction_output;
382         gc->get = adp5588_gpio_get_value;
383         gc->set = adp5588_gpio_set_value;
384         gc->can_sleep = true;
385
386         gc->base = pdata->gpio_start;
387         gc->ngpio = ADP5588_MAXGPIO;
388         gc->label = client->name;
389         gc->owner = THIS_MODULE;
390         gc->names = pdata->names;
391
392         mutex_init(&dev->lock);
393
394         ret = adp5588_gpio_read(dev->client, DEV_ID);
395         if (ret < 0)
396                 goto err;
397
398         revid = ret & ADP5588_DEVICE_ID_MASK;
399
400         for (i = 0, ret = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) {
401                 dev->dat_out[i] = adp5588_gpio_read(client, GPIO_DAT_OUT1 + i);
402                 dev->dir[i] = adp5588_gpio_read(client, GPIO_DIR1 + i);
403                 ret |= adp5588_gpio_write(client, KP_GPIO1 + i, 0);
404                 ret |= adp5588_gpio_write(client, GPIO_PULL1 + i,
405                                 (pdata->pullup_dis_mask >> (8 * i)) & 0xFF);
406                 ret |= adp5588_gpio_write(client, GPIO_INT_EN1 + i, 0);
407                 if (ret)
408                         goto err;
409         }
410
411         if (pdata->irq_base) {
412                 if (WA_DELAYED_READOUT_REVID(revid)) {
413                         dev_warn(&client->dev, "GPIO int not supported\n");
414                 } else {
415                         ret = adp5588_irq_setup(dev);
416                         if (ret)
417                                 goto err;
418                 }
419         }
420
421         ret = gpiochip_add(&dev->gpio_chip);
422         if (ret)
423                 goto err_irq;
424
425         dev_info(&client->dev, "IRQ Base: %d Rev.: %d\n",
426                         pdata->irq_base, revid);
427
428         if (pdata->setup) {
429                 ret = pdata->setup(client, gc->base, gc->ngpio, pdata->context);
430                 if (ret < 0)
431                         dev_warn(&client->dev, "setup failed, %d\n", ret);
432         }
433
434         i2c_set_clientdata(client, dev);
435
436         return 0;
437
438 err_irq:
439         adp5588_irq_teardown(dev);
440 err:
441         return ret;
442 }
443
444 static int adp5588_gpio_remove(struct i2c_client *client)
445 {
446         struct adp5588_gpio_platform_data *pdata =
447                         dev_get_platdata(&client->dev);
448         struct adp5588_gpio *dev = i2c_get_clientdata(client);
449         int ret;
450
451         if (pdata->teardown) {
452                 ret = pdata->teardown(client,
453                                       dev->gpio_chip.base, dev->gpio_chip.ngpio,
454                                       pdata->context);
455                 if (ret < 0) {
456                         dev_err(&client->dev, "teardown failed %d\n", ret);
457                         return ret;
458                 }
459         }
460
461         if (dev->irq_base)
462                 free_irq(dev->client->irq, dev);
463
464         gpiochip_remove(&dev->gpio_chip);
465
466         return 0;
467 }
468
469 static const struct i2c_device_id adp5588_gpio_id[] = {
470         {DRV_NAME, 0},
471         {}
472 };
473
474 MODULE_DEVICE_TABLE(i2c, adp5588_gpio_id);
475
476 static struct i2c_driver adp5588_gpio_driver = {
477         .driver = {
478                    .name = DRV_NAME,
479                    },
480         .probe = adp5588_gpio_probe,
481         .remove = adp5588_gpio_remove,
482         .id_table = adp5588_gpio_id,
483 };
484
485 module_i2c_driver(adp5588_gpio_driver);
486
487 MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");
488 MODULE_DESCRIPTION("GPIO ADP5588 Driver");
489 MODULE_LICENSE("GPL");