ARM64: mm: Restore memblock limit when map_mem finished.

In paging_init the memblock limit is set to restrict any addresses
returned by early_alloc to fit within the initial direct kernel
mapping in swapper_pg_dir. This allows map_mem to allocate puds,
pmds and ptes from the initial direct kernel mapping.

The limit stays low after paging_init() though, meaning any
bootmem allocations will be from a restricted subset of memory.
Gigabyte huge pages, for instance, are normally allocated from
bootmem as their order (18) is too large for the default buddy
allocator (MAX_ORDER = 11).

This patch restores the memblock limit when map_mem has finished,
allowing gigabyte huge pages (and other objects) to be allocated
from all of bootmem.

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>

mm: thp: Correct the HPAGE_PMD_ORDER check.

All Transparent Huge Pages are allocated by the buddy allocator.

A compile time check is in place that fails when the order of a
transparent huge page is too large to be allocated by the buddy
allocator. Unfortunately that compile time check passes when:
HPAGE_PMD_ORDER == MAX_ORDER
( which is incorrect as the buddy allocator can only allocate
memory of order strictly less than MAX_ORDER. )

This patch updates the compile time check to fail in the above
case.

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>

x86: mm: Remove general hugetlb code from x86.

huge_pte_alloc, huge_pte_offset and follow_huge_p[mu]d have
already been copied over to mm.

This patch removes the x86 copies of these functions and activates
the general ones by enabling:
CONFIG_ARCH_WANT_GENERAL_HUGETLB

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>

mm: hugetlb: Copy general hugetlb code from x86 to mm.

The huge_pte_alloc, huge_pte_offset and follow_huge_p[mu]d
functions in x86/mm/hugetlbpage.c do not rely on any architecture
specific knowledge other than the fact that pmds and puds can be
treated as huge ptes.

To allow other architectures to use this code (and reduce the need
for code duplication), this patch copies these functions into mm,
replaces the use of pud_large with pud_huge and provides a config
flag to activate them:
CONFIG_ARCH_WANT_GENERAL_HUGETLB

If CONFIG_ARCH_WANT_HUGE_PMD_SHARE is also active then the
huge_pmd_share code will be called by huge_pte_alloc (othewise we
call pmd_alloc and skip the sharing code).

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>

x86: mm: Remove x86 version of huge_pmd_share.

The huge_pmd_share code has been copied over to mm/hugetlb.c to
make it accessible to other architectures.

Remove the x86 copy of the huge_pmd_share code and enable the
ARCH_WANT_HUGE_PMD_SHARE config flag. That way we reference the
general one.

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>

mm: hugetlb: Copy huge_pmd_share from x86 to mm.

Under x86, multiple puds can be made to reference the same bank of
huge pmds provided that they represent a full PUD_SIZE of shared
huge memory that is aligned to a PUD_SIZE boundary.

The code to share pmds does not require any architecture specific
knowledge other than the fact that pmds can be indexed, thus can
be beneficial to some other architectures.

This patch copies the huge pmd sharing (and unsharing) logic from
x86/ to mm/ and introduces a new config option to activate it:
CONFIG_ARCH_WANTS_HUGE_PMD_SHARE

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>

Merge remote-tracking branch 'lsk/v3.10/topic/big.LITTLE' into linux-linaro-lsk

Merge branch 'for-lsk' of git://git.linaro.org/arm/big.LITTLE/mp into lsk-v3.10-big.LITTLE

Merge remote-tracking branch 'lsk/v3.10/topic/arm64-lts' into lsk-v3.10-arm64-misc

arm64: Remove __flush_dcache_page()

This function is only used in __sync_icache_dcache(), so remove it and
call __flush_dcache_area() directly. The flush_icache_user_range()
function is not used in the arm64 kernel.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
(cherry picked from commit ebd88367de80f9509bd30a09342d0a19c925b23e)
Signed-off-by: Mark Brown <broonie@linaro.org>

Merge remote-tracking branch 'lsk/v3.10/topic/arm64-usb' into linux-linaro-lsk

Merge remote-tracking branch 'lsk/v3.10/topic/usb' into linux-linaro-lsk

Conflicts:
drivers/usb/phy/phy-ulpi.c

phy: Enable USB PHY support for arm64.

Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

usb: Enable support for 64bit EHCI host controllers in arm64.

arm64 architecture handles correctly 64bit DMAs and can enable
support for 64bit EHCI host controllers.

Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

usb: Add support for Synopsis H20AHB EHCI host controller.

Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

phy: Add SMSC USB334x PHY IDs.

Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

Merge remote-tracking branch 'lsk/v3.10/topic/configs' into linux-linaro-lsk

configs: juno: Add some needed configuration

Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: Make DMA coherent and strongly ordered mappings not executable

commit de2db7432917a82b62d55bb59635586eeca6d1bd upstream.

pgprot_{dmacoherent,writecombine,noncached} don't need to generate
executable mappings with side-effects like __sync_icache_dcache() being
called when the mapping is in user space.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 73e8697b71fa956642403304b96442fd4b57ce97)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: Do not synchronise I and D caches for special ptes

commit 71fdb6bf61bf0692f004f9daf5650392c0cfe300 upstream.

Special pte mappings are not intended to be executable and do not even
have an associated struct page. This patch ensures that we do not call
__sync_icache_dcache() on such ptes.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Steve Capper <Steve.Capper@arm.com>
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit b1f2bfc9d8bb42b4e5a93470e8a0974cd4c04697)
Signed-off-by: Mark Brown <broonie@linaro.org>

ARM64: unwind: Fix PC calculation

commit e306dfd06fcb44d21c80acb8e5a88d55f3d1cf63 upstream.

The frame PC value in the unwind code used to just take the saved LR
value and use that.  That's incorrect as a stack trace, since it shows
the return path stack, not the call path stack.

In particular, it shows faulty information in case the bl is done as
the very last instruction of one label, since the return point will be
in the next label. That can easily be seen with tail calls to panic(),
which is marked __noreturn and thus doesn't have anything useful after it.

Easiest here is to just correct the unwind code and do a -4, to get the
actual call site for the backtrace instead of the return site.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit c56e0dc1b70f1537659acffc6ac8d8d615be2dae)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: add DSB after icache flush in __flush_icache_all()

commit 5044bad43ee573d0b6d90e3ccb7a40c2c7d25eb4 upstream.

Add DSB after icache flush to complete the cache maintenance operation.
The function __flush_icache_all() is used only for user space mappings
and an ISB is not required because of an exception return before executing
user instructions. An exception return would behave like an ISB.

Signed-off-by: Vinayak Kale <vkale@apm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 02599bad3774a5147eb8d98df7c9362fdc1a50c6)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: vdso: fix coarse clock handling

commit 069b918623e1510e58dacf178905a72c3baa3ae4 upstream.

When __kernel_clock_gettime is called with a CLOCK_MONOTONIC_COARSE or
CLOCK_REALTIME_COARSE clock id, it returns incorrectly to whatever the
caller has placed in x2 ("ret x2" to return from the fast path).  Fix
this by saving x30/LR to x2 only in code that will call
__do_get_tspec, restoring x30 afterward, and using a plain "ret" to
return from the routine.

Also: while the resulting tv_nsec value for CLOCK_REALTIME and
CLOCK_MONOTONIC must be computed using intermediate values that are
left-shifted by cs_shift (x12, set by __do_get_tspec), the results for
coarse clocks should be calculated using unshifted values
(xtime_coarse_nsec is in units of actual nanoseconds).  The current
code shifts intermediate values by x12 unconditionally, but x12 is
uninitialized when servicing a coarse clock.  Fix this by setting x12
to 0 once we know we are dealing with a coarse clock id.

Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit fb569d15d867a06e89b1be8278404b6fbf6b5bde)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: Invalidate the TLB when replacing pmd entries during boot

commit a55f9929a9b257f84b6cc7b2397379cabd744a22 upstream.

With the 64K page size configuration, __create_page_tables in head.S
maps enough memory to get started but using 64K pages rather than 512M
sections with a single pgd/pud/pmd entry pointing to a pte table.
create_mapping() may override the pgd/pud/pmd table entry with a block
(section) one if the RAM size is more than 512MB and aligned correctly.
For the end of this block to be accessible, the old TLB entry must be
invalidated.

Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit f35f27e775d6f8aa265fb698975c9c95f2757ef4)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: vdso: prevent ld from aligning PT_LOAD segments to 64k

commit 40507403485fcb56b83d6ddfc954e9b08305054c upstream.

Whilst the text segment for our VDSO is marked as PT_LOAD in the ELF
headers, it is mapped by the kernel and not actually subject to
demand-paging. ld doesn't realise this, and emits a p_align field of 64k
(the maximum supported page size), which conflicts with the load address
picked by the kernel on 4k systems, which will be 4k aligned. This
causes GDB to fail with "Failed to read a valid object file image from
memory" when attempting to load the VDSO.

This patch passes the -n option to ld, which prevents it from aligning
PT_LOAD segments to the maximum page size.

Reported-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 6737eaebff6297e5b6aeb458a4b4ad4b61df8f57)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: vdso: update wtm fields for CLOCK_MONOTONIC_COARSE

commit d4022a335271a48cce49df35d825897914fbffe3 upstream.

Update wall-to-monotonic fields in the VDSO data page
unconditionally.  These are used to service CLOCK_MONOTONIC_COARSE,
which is not guarded by use_syscall.

Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit b666f382900c74f23c78556777041c2ceb7c2b24)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: Use Normal NonCacheable memory for writecombine

commit 4f00130b70e5eee813cc7bc298e0f3fdf79673cc upstream.

This provides better performance compared to Device GRE and also allows
unaligned accesses. Such memory is intended to be used with standard RAM
(e.g. framebuffers) and not I/O.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 3655a197b1ea3ce989d34868768c5f4b6205061c)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: Do not flush the D-cache for anonymous pages

commit 7249b79f6b4cc3c2aa9138dca52e535a4c789107 upstream.

The D-cache on AArch64 is VIPT non-aliasing, so there is no need to
flush it for anonymous pages.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit fc54900e08d840fcfec9e5d2fba2c6f233aa49b9)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: Avoid cache flushing in flush_dcache_page()

commit b5b6c9e9149d8a7c3f1d7b9d0c046c6184e1dd17 upstream.

The flush_dcache_page() function is called when the kernel modified a
page cache page. Since the D-cache on AArch64 does not have aliases
this function can simply mark the page as dirty for later flushing via
set_pte_at()/__sync_icache_dcache() if the page is executable (to ensure
the I-D cache coherency).

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 1e616427f20943c9966296dfff9e7a2b825846aa)
Signed-off-by: Mark Brown <broonie@linaro.org>

clocksource: arch_timer: use virtual counters

commit 0d651e4e65e96989f72236bf83bd4c6e55eb6ce4 upstream.

Switching between reading the virtual or physical counters is
problematic, as some core code wants a view of time before we're fully
set up. Using a function pointer and switching the source after the
first read can make time appear to go backwards, and having a check in
the read function is an unfortunate block on what we want to be a fast
path.

Instead, this patch makes us always use the virtual counters. If we're a
guest, or don't have hyp mode, we'll use the virtual timers, and as such
don't care about CNTVOFF as long as it doesn't change in such a way as
to make time appear to travel backwards. As the guest will use the
virtual timers, a (potential) KVM host must use the physical timers
(which can wake up the host even if they fire while a guest is
executing), and hence a host must have CNTVOFF set to zero so as to have
a consistent view of time between the physical timers and virtual
counters.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 714c21cb90951905b269870087a99c37f3a7af0c)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: Remove unused cpu_name ascii in arch/arm64/mm/proc.S

commit f3a1d7d53dccf51959aec16b574617cc6bfeca09 upstream.

This string has been moved to arch/arm64/kernel/cputable.c.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit ae5092fadd50cfd0d29e762771d30cbf7f2c2fec)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: dts: Reserve the memory used for secondary CPU release address

commit df503ba7f653c590b475ab80bde788edf5af70d5 upstream.

With the spin-table SMP booting method, secondary CPUs poll a location
passed in the DT. The foundation-v8.dts file doesn't have this memory
reserved and there is a risk of Linux using it before secondary CPUs are
started.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 29f37087bb51dfe4ff61daad60bd93f7bcfa3d72)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: check for number of arguments in syscall_get/set_arguments()

commit 7b22c03536a539142f931815528d55df455ffe2d upstream.

In ftrace_syscall_enter(),
    syscall_get_arguments(..., 0, n, ...)
        if (i == 0) { <handle orig_x0> ...; n--;}
        memcpy(..., n * sizeof(args[0]));
If 'number of arguments(n)' is zero and 'argument index(i)' is also zero in
syscall_get_arguments(), none of arguments should be copied by memcpy().
Otherwise 'n--' can be a big positive number and unexpected amount of data
will be copied. Tracing system calls which take no argument, say sync(void),
may hit this case and eventually make the system corrupted.
This patch fixes the issue both in syscall_get_arguments() and
syscall_set_arguments().

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit e2956ef5b5ddb3ede70962afe9297d8340787fa6)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: fix possible invalid FPSIMD initialization state

commit 6db83cea1c975b9a102e17def7d2795814e1ae2b upstream.

If context switching happens during executing fpsimd_flush_thread(),
stale value in FPSIMD registers will be saved into current thread's
fpsimd_state by fpsimd_thread_switch(). That may cause invalid
initialization state for the new process, so disable preemption
when executing fpsimd_flush_thread().

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 2bf5861acf602fe6201ac1f82955ac7283e56b6f)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: Change kernel stack size to 16K

commit 845ad05ec31e0f3872a321e10dbeaf872022632c upstream.

Written by Catalin Marinas, tested by APM on storm platform. This is needed
because of the failures encountered when running SpecWeb benchmark test.

Signed-off-by: Feng Kan <fkan@apm.com>
Acked-by: Kumar Sankaran <ksankaran@apm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 79f783f05539479676406d3d42c3d86bd203f083)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: virt: ensure visibility of __boot_cpu_mode

commit 82b2f495fba338d1e3098dde1df54944a9c19751 upstream.

Secondary CPUs write to __boot_cpu_mode with caches disabled, and thus a
cached value of __boot_cpu_mode may be incoherent with that in memory.
This could lead to a failure to detect mismatched boot modes.

This patch adds flushing to ensure that writes by secondaries to
__boot_cpu_mode are made visible before we test against it.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 5fb08df3dd1f7b8e83936808b042725a8b067562)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: Only enable local interrupts after the CPU is marked online

commit 53ae3acd4390ffeecb3a11dbd5be347b5a3d98f2 upstream.

There is a slight chance that (timer) interrupts are triggered before a
secondary CPU has been marked online with implications on softirq thread
affinity.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Kirill Tkhai <tkhai@yandex.ru>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 81ca15a3e04961b54d4a0b395e681bffb6cfbc68)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: spinlock: retry trylock operation if strex fails on free lock

commit 4ecf7ccb1973fd826456b6ab1e6dfafe9023c753 upstream.

An exclusive store instruction may fail for reasons other than lock
contention (e.g. a cache eviction during the critical section) so, in
line with other architectures using similar exclusive instructions
(alpha, mips, powerpc), retry the trylock operation if the lock appears
to be free but the strex reported failure.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Tony Thompson <anthony.thompson@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 42b5bb47a62b7b2d8cd0b9af58f914c5e83ef76e)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events

commit cdc27c27843248ae7eb0df5fc261dd004eaa5670 upstream.

Commit 8f34a1da35ae ("arm64: ptrace: use HW_BREAKPOINT_EMPTY type for
disabled breakpoints") fixed an issue with GDB trying to zero breakpoint
control registers. The problem there is that the arch hw_breakpoint code
will attempt to create a (disabled), execute breakpoint of length 0.

This will fail validation and report unexpected failure to GDB. To avoid
this, we treated disabled breakpoints as HW_BREAKPOINT_EMPTY, but that
seems to have broken with recent kernels, causing watchpoints to be
treated as TYPE_INST in the core code and returning ENOSPC for any
further breakpoints.

This patch fixes the problem by prioritising the `enable' field of the
breakpoint: if it is cleared, we simply update the perf_event_attr to
indicate that the thing is disabled and don't bother changing either the
type or the length. This reinforces the behaviour that the breakpoint
control register is essentially read-only apart from the enable bit
when disabling a breakpoint.

Reported-by: Aaron Liu <liucy214@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 11b81802921618b02122855db021a63df7d9fd49)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: perf: fix ARMv8 EVTYPE_MASK to include NSH bit

commit 178cd9ce377232518ec17ff2ecab2e80fa60784c upstream.

This is a port of f2fe09b055e2 ("ARM: 7663/1: perf: fix ARMv7 EVTYPE_MASK
to include NSH bit") to arm64, which fixes the broken evtype mask to
include the NSH bit, allowing profiling at EL2.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 0fe9a0dc92a64c088e76fcd3d35b2ba36b4d7f3c)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: perf: fix group validation when using enable_on_exec

commit 8455e6ec70f33b0e8c3ffd47067e00481f09f454 upstream.

This is a port of cb2d8b342aa0 ("ARM: 7698/1: perf: fix group validation
when using enable_on_exec") to arm64, which fixes the event validation
checking so that events in the OFF state are still considered when
enable_on_exec is true.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 1f96d83b38937294584ede9473c2b2961528f287)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: perf: fix event validation for software group leaders

commit ee7538a008a45050c8f706d38b600f55953169f9 upstream.

This is a port of c95eb3184ea1 ("ARM: 7809/1: perf: fix event validation
for software group leaders") to arm64, which fixes a panic in the arm64
perf backend found as a result of Vince's fuzzing tool.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 6c6f6c7166e9ee45e545eab850a2862a92c135b2)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: perf: fix array out of bounds access in armpmu_map_hw_event()

commit 868f6fea8fa63f09acbfa93256d0d2abdcabff79 upstream.

This is a port of d9f966357b14 ("ARM: 7810/1: perf: Fix array out of
bounds access in armpmu_map_hw_event()") to arm64, which fixes an oops
in the arm64 perf backend found as a result of Vince's fuzzing tool.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 975a3cd4cc0dff06a635cb16b8fb25fd3ae88234)
Signed-off-by: Mark Brown <broonie@linaro.org>

arm64: mm: don't treat user cache maintenance faults as writes

commit db6f41063cbdb58b14846e600e6bc3f4e4c2e888 upstream.

On arm64, cache maintenance faults appear as data aborts with the CM
bit set in the ESR. The WnR bit, usually used to distinguish between
faulting loads and stores, always reads as 1 and (slightly confusingly)
the instructions are treated as reads by the architecture.

This patch fixes our fault handling code to treat cache maintenance
faults in the same way as loads.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 88c0a794e5d9bcc29926e636cd1d6eb5c9dcb235)
Signed-off-by: Mark Brown <broonie@linaro.org>

Linux 3.10.40

ARC: !PREEMPT: Ensure Return to kernel mode is IRQ safe

commit 8aa9e85adac609588eeec356e5a85059b3b819ba upstream.

There was a very small race window where resume to kernel mode from a
Exception Path (or pure kernel mode which is true for most of ARC
exceptions anyways), was not disabling interrupts in restore_regs,
clobbering the exception regs

Anton found the culprit call flow (after many sleepless nights)

| 1. we got a Trap from user land
| 2. started to service it.
| 3. While doing some stuff on user-land memory (I think it is padzero()),
|     we got a DataTlbMiss
| 4. On return from it we are taking "resume_kernel_mode" path
| 5. NEED_RESHED is not set, so we go to "return from exception" path in
|     restore regs.
| 6. there seems to be IRQ happening

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Anton Kolesov <Anton.Kolesov@synopsys.com>
Cc: Francois Bedard <Francois.Bedard@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: cirrus: add power management support

commit 2f1e800799bf478494cec3573cd63eb34ca89c9d upstream.

cirrus kms driver lacks power management support, thus
the vga display doesn't work any more after S3 resume.

Fix this by adding suspend and resume functions.
Also make the mode_set function unblank the screen.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: synaptics - add min/max quirk for ThinkPad Edge E431

commit 27a38856a948c3e8de30dc71647ff9e1778c99fc upstream.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1

commit 46a2986ebbe18757c2d8c352f8fb6e0f4f0754e3 upstream.

We expect that all the Haswell series will need such quirks, sigh.

The T431s seems to be T430 hardware in a T440s case, using the T440s touchpad,
with the same min/max issue.

The X1 Carbon 3rd generation name says 2nd while it is a 3rd generation.

The X1 and T431s share a PnPID with the T540p, but the reported ranges are
closer to those of the T440s.

HdG: Squashed 5 quirk patches into one. T431s + L440 + L540 are written by me,
S1 Yoga and X1 are written by Benjamin Tissoires.

Hdg: Standardized S1 Yoga and X1 values, Yoga uses the same touchpad as the
X240, X1 uses the same touchpad as the T440.

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lockd: ensure we tear down any live sockets when socket creation fails during lockd_up

commit 679b033df48422191c4cac52b610d9980e019f9b upstream.

We had a Fedora ABRT report with a stack trace like this:

kernel BUG at net/sunrpc/svc.c:550!
invalid opcode: 0000 [#1] SMP
[...]
CPU: 2 PID: 913 Comm: rpc.nfsd Not tainted 3.13.6-200.fc20.x86_64 #1
Hardware name: Hewlett-Packard HP ProBook 4740s/1846, BIOS 68IRR Ver. F.40 01/29/2013
task: ffff880146b00000 ti: ffff88003f9b8000 task.ti: ffff88003f9b8000
RIP: 0010:[<ffffffffa0305fa8>]  [<ffffffffa0305fa8>] svc_destroy+0x128/0x130 [sunrpc]
RSP: 0018:ffff88003f9b9de0  EFLAGS: 00010206
RAX: ffff88003f829628 RBX: ffff88003f829600 RCX: 00000000000041ee
RDX: 0000000000000000 RSI: 0000000000000286 RDI: 0000000000000286
RBP: ffff88003f9b9de8 R08: 0000000000017360 R09: ffff88014fa97360
R10: ffffffff8114ce57 R11: ffffea00051c9c00 R12: ffff88003f829600
R13: 00000000ffffff9e R14: ffffffff81cc7cc0 R15: 0000000000000000
FS:  00007f4fde284840(0000) GS:ffff88014fa80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f4fdf5192f8 CR3: 00000000a569a000 CR4: 00000000001407e0
Stack:
 ffff88003f792300 ffff88003f9b9e18 ffffffffa02de02a 0000000000000000
 ffffffff81cc7cc0 ffff88003f9cb000 0000000000000008 ffff88003f9b9e60
 ffffffffa033bb35 ffffffff8131c86c ffff88003f9cb000 ffff8800a5715008
Call Trace:
 [<ffffffffa02de02a>] lockd_up+0xaa/0x330 [lockd]
 [<ffffffffa033bb35>] nfsd_svc+0x1b5/0x2f0 [nfsd]
 [<ffffffff8131c86c>] ? simple_strtoull+0x2c/0x50
 [<ffffffffa033c630>] ? write_pool_threads+0x280/0x280 [nfsd]
 [<ffffffffa033c6bb>] write_threads+0x8b/0xf0 [nfsd]
 [<ffffffff8114efa4>] ? __get_free_pages+0x14/0x50
 [<ffffffff8114eff6>] ? get_zeroed_page+0x16/0x20
 [<ffffffff811dec51>] ? simple_transaction_get+0xb1/0xd0
 [<ffffffffa033c098>] nfsctl_transaction_write+0x48/0x80 [nfsd]
 [<ffffffff811b8b34>] vfs_write+0xb4/0x1f0
 [<ffffffff811c3f99>] ? putname+0x29/0x40
 [<ffffffff811b9569>] SyS_write+0x49/0xa0
 [<ffffffff810fc2a6>] ? __audit_syscall_exit+0x1f6/0x2a0
 [<ffffffff816962e9>] system_call_fastpath+0x16/0x1b
Code: 31 c0 e8 82 db 37 e1 e9 2a ff ff ff 48 8b 07 8b 57 14 48 c7 c7 d5 c6 31 a0 48 8b 70 20 31 c0 e8 65 db 37 e1 e9 f4 fe ff ff 0f 0b <0f> 0b 66 0f 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 41 56 41 55
RIP  [<ffffffffa0305fa8>] svc_destroy+0x128/0x130 [sunrpc]
 RSP <ffff88003f9b9de0>

Evidently, we created some lockd sockets and then failed to create
others. make_socks then returned an error and we tried to tear down the
svc, but svc->sv_permsocks was not empty so we ended up tripping over
the BUG() in svc_destroy().

Fix this by ensuring that we tear down any live sockets we created when
socket creation is going to return an error.

Fixes: 786185b5f8abefa (SUNRPC: move per-net operations from...)
Reported-by: Raphos <raphoszap@laposte.net>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm thin: fix dangling bio in process_deferred_bios error path

commit fe76cd88e654124d1431bb662a0fc6e99ca811a5 upstream.

If unable to ensure_next_mapping() we must add the current bio, which
was removed from the @bios list via bio_list_pop, back to the
deferred_bios list before all the remaining @bios.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm transaction manager: fix corruption due to non-atomic transaction commit

commit a9d45396f5956d0b615c7ae3b936afd888351a47 upstream.

The persistent-data library used by dm-thin, dm-cache, etc is
transactional.  If anything goes wrong, such as an io error when writing
new metadata or a power failure, then we roll back to the last
transaction.

Atomicity when committing a transaction is achieved by:

a) Never overwriting data from the previous transaction.
b) Writing the superblock last, after all other metadata has hit the
   disk.

This commit and the following commit ("dm: take care to copy the space
map roots before locking the superblock") fix a bug associated with (b).
When committing it was possible for the superblock to still be written
in spite of an io error occurring during the preceeding metadata flush.
With these commits we're careful not to take the write lock out on the
superblock until after the metadata flush has completed.

Change the transaction manager's semantics for dm_tm_commit() to assume
all data has been flushed _before_ the single superblock that is passed
in.

As a prerequisite, split the block manager's block unlocking and
flushing by simplifying dm_bm_flush_and_unlock() to dm_bm_flush().  Now
the unlocking must be done separately.

This issue was discovered by forcing io errors at the crucial time
using dm-flakey.

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Skip intel_crt_init for Dell XPS 8700

commit 10b6ee4a87811a110cb01eaca01eb04da6801baf upstream.

The Dell XPS 8700 has a onboard Display port and HDMI port and no VGA port.
The call intel_crt_init freeze the machine, so skip such call.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73559
Signed-off-by: Giacomo Comes <comes at naic.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: sm_ftl: heap corruption in sm_create_sysfs_attributes()

commit b4c233057771581698a13694ab6f33b48ce837dc upstream.

We always put a NUL terminator one space past the end of the "vendor"
buffer.  Walter Harms also pointed out that this should just use
kstrndup().

Fixes: 7d17c02a01a1 ('mtd: Add new SmartMedia/xD FTL')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: nuc900_nand: NULL dereference in nuc900_nand_enable()

commit c69dbbf3335a21aae74376d7e5db50a486d52439 upstream.

Instead of writing to "nand->reg + REG_FMICSR" we write to "REG_FMICSR"
which is NULL and not a valid register.

Fixes: 8bff82cbc308 ('mtd: add nand support for w90p910 (v2)')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: atmel_nand: Disable subpage NAND write when using Atmel PMECC

commit 90445ff6241e2a13445310803e2efa606c61f276 upstream.

Crash detected on sam5d35 and its pmecc nand ecc controller.

The problem was a call to chip->ecc.hwctl from nand_write_subpage_hwecc
(nand_base.c) when we write a sub page.
chip->ecc.hwctl function is not set when we are using PMECC controller.
As a workaround, set NAND_NO_SUBPAGE_WRITE for PMECC controller in
order to disable sub page access in nand_write_page.

Signed-off-by: Herve Codina <Herve.CODINA@celad.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tgafb: fix data copying

commit 6b0df6827bb6fcacb158dff29ad0a62d6418b534 upstream.

The functions for data copying copyarea_foreward_8bpp and
copyarea_backward_8bpp are buggy, they produce screen corruption.

This patch fixes the functions and moves the logic to one function
"copyarea_8bpp". For simplicity, the function only handles copying that
is aligned on 8 pixes. If we copy an unaligned area, generic function
cfb_copyarea is used.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: mxs: Allow for recursive enable_irq_wake() call

commit a585f87c863e4e1d496459d382b802bf5ebe3717 upstream.

The scenario here is that someone calls enable_irq_wake() from somewhere
in the code. This will result in the lockdep producing a backtrace as can
be seen below. In my case, this problem is triggered when using the wl1271
(TI WlCore) driver found in drivers/net/wireless/ti/ .

The problem cause is rather obvious from the backtrace, but let's outline
the dependency. enable_irq_wake() grabs the IRQ buslock in irq_set_irq_wake(),
which in turns calls mxs_gpio_set_wake_irq() . But mxs_gpio_set_wake_irq()
calls enable_irq_wake() again on the one-level-higher IRQ , thus it tries to
grab the IRQ buslock again in irq_set_irq_wake() . Because the spinlock in
irq_set_irq_wake()->irq_get_desc_buslock()->__irq_get_desc_lock() is not
marked as recursive, lockdep will spew the stuff below.

We know we can safely re-enter the lock, so use IRQ_GC_INIT_NESTED_LOCK to
fix the spew.

 =============================================
 [ INFO: possible recursive locking detected ]
 3.10.33-00012-gf06b763-dirty #61 Not tainted
 ---------------------------------------------
 kworker/0:1/18 is trying to acquire lock:
  (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88

 but task is already holding lock:
  (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock(&irq_desc_lock_class);
   lock(&irq_desc_lock_class);

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 3 locks held by kworker/0:1/18:
  #0:  (events){.+.+.+}, at: [<c0036308>] process_one_work+0x134/0x4a4
  #1:  ((&fw_work->work)){+.+.+.}, at: [<c0036308>] process_one_work+0x134/0x4a4
  #2:  (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88

 stack backtrace:
 CPU: 0 PID: 18 Comm: kworker/0:1 Not tainted 3.10.33-00012-gf06b763-dirty #61
 Workqueue: events request_firmware_work_func
 [<c0013eb4>] (unwind_backtrace+0x0/0xf0) from [<c0011c74>] (show_stack+0x10/0x14)
 [<c0011c74>] (show_stack+0x10/0x14) from [<c005bb08>] (__lock_acquire+0x140c/0x1a64)
 [<c005bb08>] (__lock_acquire+0x140c/0x1a64) from [<c005c6a8>] (lock_acquire+0x9c/0x104)
 [<c005c6a8>] (lock_acquire+0x9c/0x104) from [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58)
 [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) from [<c00685f0>] (__irq_get_desc_lock+0x48/0x88)
 [<c00685f0>] (__irq_get_desc_lock+0x48/0x88) from [<c0068e78>] (irq_set_irq_wake+0x20/0xf4)
 [<c0068e78>] (irq_set_irq_wake+0x20/0xf4) from [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24)
 [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) from [<c0068cf4>] (set_irq_wake_real+0x30/0x44)
 [<c0068cf4>] (set_irq_wake_real+0x30/0x44) from [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4)
 [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) from [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c)
 [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c) from [<c02be5e8>] (request_firmware_work_func+0x38/0x58)
 [<c02be5e8>] (request_firmware_work_func+0x38/0x58) from [<c0036394>] (process_one_work+0x1c0/0x4a4)
 [<c0036394>] (process_one_work+0x1c0/0x4a4) from [<c0036a4c>] (worker_thread+0x138/0x394)
 [<c0036a4c>] (worker_thread+0x138/0x394) from [<c003cb74>] (kthread+0xa4/0xb0)
 [<c003cb74>] (kthread+0xa4/0xb0) from [<c000ee00>] (ret_from_fork+0x14/0x34)
 wlcore: loaded

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8188ee: initialize packet_beacon

commit 328e203fc35f0b4f6df1c4943f74cf553bcc04f8 upstream.

static code analysis from cppcheck reports:

[drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:322]:
  (error) Uninitialized variable: packet_beacon

packet_beacon is not initialized and hence packet_beacon
contains garbage from the stack, so set it to false.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192se: Fix regression due to commit 1bf4bbb

commit 5f9186990ec4579ee5b7a99b3254c29eda479f36 upstream.

Beginning with kernel 3.13, this driver fails on some systems. The problem
was bisected to:

Commit 1bf4bbb4024dcdab5e57634dd8ae1072d42a53ac
Author: Felix Fietkau <nbd@openwrt.org>
Title: mac80211: send control port protocol frames to the VO queue

There is noting wrong with the above commit. The regression occurs because
V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to
modify the rtl8192se routine that sets the correct transmit queue.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=74541

Reported-by: Alex Miller <almiller_1@yahoo.co.uk>
Tested-by: Alex Miller <almiller_1@yahoo.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192se: Fix too long disable of IRQs

commit 2610decdd0b3808ba20471a999835cfee5275f98 upstream.

In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8192se.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Fix too long disable of IRQs

commit a53268be0cb9763f11da4f6fe3fb924cbe3a7d4a upstream.

In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8192cu.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8188ee: Fix too long disable of IRQs

commit 6b6392715856d563719991e9ce95e773491a8983 upstream.

In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8188ee.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8723ae: Fix too long disable of IRQs

commit bfc1010c418a22cbebd8b1bd1e75dad6a527a609 upstream.

In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8723ae.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locks: allow __break_lease to sleep even when break_time is 0

commit 4991a628a789dc5954e98e79476d9808812292ec upstream.

A fl->fl_break_time of 0 has a special meaning to the lease break code
that basically means "never break the lease". knfsd uses this to ensure
that leases don't disappear out from under it.

Unfortunately, the code in __break_lease can end up passing this value
to wait_event_interruptible as a timeout, which prevents it from going
to sleep at all. This causes __break_lease to spin in a tight loop and
causes soft lockups.

Fix this by ensuring that we pass a minimum value of 1 as a timeout
instead.

Cc: J. Bruce Fields <bfields@fieldses.org>
Reported-by: Terry Barnaby <terry1@beam.ltd.uk>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: exclude AP_VLAN interfaces from tx power calculation

commit 764152ff66f4a8be1f9d7981e542ffdaa5bd7aff upstream.

Their power value is initialized to zero. This patch fixes an issue
where the configured power drops to the minimum value when AP_VLAN
interfaces are created/removed.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix software remain-on-channel implementation

commit 115b943a6ea12656088fa1ff6634c0d30815e55b upstream.

Jouni reported that when doing off-channel transmissions mixed
with on-channel transmissions, the on-channel ones ended up on
the off-channel in some cases.

The reason for that is that during the refactoring of the off-
channel code, I lost the part that stopped all activity and as
a consequence the on-channel frames (including data frames)
were no longer queued but would be transmitted on the temporary
channel.

Fix this by simply restoring the lost activity stop call.

Fixes: 2eb278e083549 ("mac80211: unify SW/offload remain-on-channel")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix WPA with VLAN on AP side with ps-sta again

commit 112c44b2df0984121a52fbda89425843b8e1a457 upstream.

commit de74a1d9032f4d37ea453ad2a647e1aff4cd2591
  "mac80211: fix WPA with VLAN on AP side with ps-sta"
fixed an issue where queued multicast packets would
be sent out encrypted with the key of an other bss.

commit "7cbf9d017dbb5e3276de7d527925d42d4c11e732"
  "mac80211: fix oops on mesh PS broadcast forwarding"
essentially reverted it, because vif.type cannot be AP_VLAN
due to the check to vif.type in ieee80211_get_buffered_bc before.

As the later commit intended to fix the MESH case, fix it
by checking for IFTYPE_AP instead of IFTYPE_AP_VLAN.

Fixes: 7cbf9d017dbb ("mac80211: fix oops on mesh PS broadcast forwarding")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: dvm: take mutex when sending SYNC BT config command

commit 82e5a649453a3cf23516277abb84273768a1592b upstream.

There is a flow in which we send the host command in SYNC
mode, but we don't take priv->mutex.

Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1046495
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libata/ahci: accommodate tag ordered controllers

commit 8a4aeec8d2d6a3edeffbdfae451cdf05cbf0fefd upstream.

The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order:

5.3.2.12 P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.

The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.

This behavior has likely been hidden by drives that arrange for commands
to complete in issue order.  However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course.  So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.

This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.

Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio.  Also, word is that recent versions of an unnamed
OS also does it this way now.  So, drives in the field are already
experienced with this tag ordering scheme.

Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ed Ciechanowski <ed.ciechanowski@intel.com>
Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: Fix machine check error due to improper access of B43_MMIO_PSM_PHY_HDR

commit 12cd43c6ed6da7bf7c5afbd74da6959cda6d056b upstream.

Register B43_MMIO_PSM_PHY_HDR is 16 bit one, so accessing it with 32b
functions isn't safe. On my machine it causes delayed (!) CPU exception:

Disabling lock debugging due to kernel taint
mce: [Hardware Error]: CPU 0: Machine Check Exception: 4 Bank 4: b200000000070f0f
mce: [Hardware Error]: TSC 164083803dc
mce: [Hardware Error]: PROCESSOR 2:20fc2 TIME 1396650505 SOCKET 0 APIC 0 microcode 0
mce: [Hardware Error]: Run the above through 'mcelog --ascii'
mce: [Hardware Error]: Machine check: Processor context corrupt
Kernel panic - not syncing: Fatal machine check on current CPU
Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mach64: fix cursor when character width is not a multiple of 8 pixels

commit 43751a1b8ee2e70ce392bf31ef3133da324e68b3 upstream.

This patch fixes the hardware cursor on mach64 when font width is not a
multiple of 8 pixels.

If you load such a font, the cursor is expanded to the next 8-byte
boundary and a part of the next character after the cursor is not
visible.
For example, when you load a font with 12-pixel width, the cursor width
is 16 pixels and when the cursor is displayed, 4 pixels of the next
character are not visible.

The reason is this: atyfb_cursor is called with proper parameters to
load an image that is 12-pixel wide. However, the number is aligned on
the next 8-pixel boundary on the line
"unsigned int width = (cursor->image.width + 7) >> 3;" and the whole
function acts as it is was loading a 16-pixel image.

This patch fixes it so that the value written to the framebuffer is
padded with 0xaaaa (the transparent pattern) when the image size it not
a multiple of 8 pixels. The transparent pattern causes that the cursor
will not interfere with the next character.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mach64: use unaligned access

commit c29dd8696dc5dbd50b3ac441b8a26751277ba520 upstream.

This patch fixes mach64 to use unaligned access to the font bitmap.

This fixes unaligned access warning on sparc64 when 14x8 font is loaded.

On x86(64), unaligned access is handled in hardware, so both functions
le32_to_cpup and get_unaligned_le32 perform the same operation.

On RISC machines, unaligned access is not handled in hardware, so we
better use get_unaligned_le32 to avoid the unaligned trap and warning.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

matroxfb: restore the registers M_ACCESS and M_PITCH

commit a772d4736641ec1b421ad965e13457c17379fc86 upstream.

When X11 is running and the user switches back to console, the card
modifies the content of registers M_MACCESS and M_PITCH in periodic
intervals.

This patch fixes it by restoring the content of these registers before
issuing any accelerator command.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

framebuffer: fix cfb_copyarea

commit 00a9d699bc85052d2d3ed56251cd928024ce06a3 upstream.

The function cfb_copyarea is buggy when the copy operation is not aligned on
long boundary (4 bytes on 32-bit machines, 8 bytes on 64-bit machines).

How to reproduce:
- use x86-64 machine
- use a framebuffer driver without acceleration (for example uvesafb)
- set the framebuffer to 8-bit depth
(for example fbset -a 1024x768-60 -depth 8)
- load a font with character width that is not a multiple of 8 pixels
note: the console-tools package cannot load a font that has
width different from 8 pixels. You need to install the packages
"kbd" and "console-terminus" and use the program "setfont" to
set font width (for example: setfont Uni2-Terminus20x10)
- move some text left and right on the bash command line and you get a
screen corruption

To expose more bugs, put this line to the end of uvesafb_init_info:
info->flags |= FBINFO_HWACCEL_COPYAREA | FBINFO_READS_FAST;
- Now framebuffer console will use cfb_copyarea for console scrolling.
You get a screen corruption when console is scrolled.

This patch is a rewrite of cfb_copyarea. It fixes the bugs, with this
patch, console scrolling in 8-bit depth with a font width that is not a
multiple of 8 pixels works fine.

The cfb_copyarea code was very buggy and it looks like it was written
and never tried with non-8-pixel font.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: Entry Handler tweaks: Optimize away redundant IRQ_DISABLE_SAVE

commit fce16bc35ae4a45634f3dc348d8d297a25c277cf upstream.

In the exception return path, for both U/K cases, intr are already
disabled (for various existing reasons). So when we drop down to
@restore_regs, we need not redo that.

There was subtle issue - when intr were NOT being disabled for
ret-to-kernel-but-no-preemption case - now fixed by moving the
IRQ_DISABLE further up in @resume_kernel_mode.

So what do we gain:

* Shaves off a few insn in return path.

* Eliminates the need for IRQ_DISABLE_SAVE assembler macro for ARCv2
  hence allows for entry code sharing.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: Entry Handler tweaks: Simplify branch for in-kernel preemption

commit 147aece29b15051173eb1e767018135361cdba89 upstream.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/bpf,jit: initialize A register if 1st insn is BPF_S_LDX_B_MSH

commit 6e0de817594c61f3b392a9245deeb09609ec707d upstream.

The A register needs to be initialized to zero in the prolog if the
first instruction of the BPF program is BPF_S_LDX_B_MSH to prevent
leaking the content of %r5 to user space.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/chsc: fix SEI usage on old FW levels

commit 06cd7a874ec6e09d151aeb1fa8600e14f1ff89f6 upstream.

Using a notification type mask for the store event information chsc
is unsupported on some firmware levels. Retry SEI with that mask set
to zero (which is the old way of requesting only channel subsystem
related events).

Reported-and-tested-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/tm: Disable IRQ in tm_recheckpoint

commit e6b8fd028b584ffca7a7255b8971f254932c9fce upstream.

We can't take an IRQ when we're about to do a trechkpt as our GPR state is set
to user GPR values.

We've hit this when running some IBM Java stress tests in the lab resulting in
the following dump:

  cpu 0x3f: Vector: 700 (Program Check) at [c000000007eb3d40]
      pc: c000000000050074: restore_gprs+0xc0/0x148
      lr: 00000000b52a8184
      sp: ac57d360
     msr: 8000000100201030
    current = 0xc00000002c500000
    paca    = 0xc000000007dbfc00     softe: 0     irq_happened: 0x00
      pid   = 34535, comm = Pooled Thread #
  R00 = 00000000b52a8184   R16 = 00000000b3e48fda
  R01 = 00000000ac57d360   R17 = 00000000ade79bd8
  R02 = 00000000ac586930   R18 = 000000000fac9bcc
  R03 = 00000000ade60000   R19 = 00000000ac57f930
  R04 = 00000000f6624918   R20 = 00000000ade79be8
  R05 = 00000000f663f238   R21 = 00000000ac218a54
  R06 = 0000000000000002   R22 = 000000000f956280
  R07 = 0000000000000008   R23 = 000000000000007e
  R08 = 000000000000000a   R24 = 000000000000000c
  R09 = 00000000b6e69160   R25 = 00000000b424cf00
  R10 = 0000000000000181   R26 = 00000000f66256d4
  R11 = 000000000f365ec0   R27 = 00000000b6fdcdd0
  R12 = 00000000f66400f0   R28 = 0000000000000001
  R13 = 00000000ada71900   R29 = 00000000ade5a300
  R14 = 00000000ac2185a8   R30 = 00000000f663f238
  R15 = 0000000000000004   R31 = 00000000f6624918
  pc  = c000000000050074 restore_gprs+0xc0/0x148
  cfar= c00000000004fe28 dont_restore_vec+0x1c/0x1a4
  lr  = 00000000b52a8184
  msr = 8000000100201030   cr  = 24804888
  ctr = 0000000000000000   xer = 0000000000000000   trap =  700

This moves tm_recheckpoint to a C function and moves the tm_restore_sprs into
that function.  It then adds IRQ disabling over the trechkpt critical section.
It also sets the TEXASR FS in the signals code to ensure this is never set now
that we explictly write the TM sprs in tm_recheckpoint.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/compat: 32-bit little endian machine name is ppcle, not ppc

commit 422b9b9684db3c511e65c91842275c43f5910ae9 upstream.

I noticed this when testing setarch. No, we don't magically
support a big endian userspace on a little endian kernel.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mpt2sas: Don't disable device twice at suspend.

commit af61e27c3f77c7623b5335590ae24b6a5c323e22 upstream.

On suspend, _scsih_suspend calls mpt2sas_base_free_resources, which
in turn calls pci_disable_device if the device is enabled prior to
suspending. However, _scsih_suspend also calls pci_disable_device
itself.

Thus, in the event that the device is enabled prior to suspending,
pci_disable_device will be called twice. This patch removes the
duplicate call to pci_disable_device in _scsi_suspend as it is both
unnecessary and results in a kernel oops.

Signed-off-by: Tyler Stachecki <tstache1@binghamton.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio-scsi: Skip setting affinity on uninitialized vq

commit 0c8482ac92db5ac15792caf23b7f7df9e4f48ae1 upstream.

virtscsi_init calls virtscsi_remove_vqs on err, even before initializing
the vqs. The latter calls virtscsi_set_affinity, so let's check the
pointer there before setting affinity on it.

This fixes a panic when setting device's num_queues=2 on RHEL 6.5:

qemu-system-x86_64 ... \
-device virtio-scsi-pci,id=scsi0,addr=0x13,...,num_queues=2 \
-drive file=/stor/vm/dummy.raw,id=drive-scsi-disk,... \
-device scsi-hd,drive=drive-scsi-disk,...

[    0.354734] scsi0 : Virtio SCSI HBA
[    0.379504] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[    0.380141] IP: [<ffffffff814741ef>] __virtscsi_set_affinity+0x4f/0x120
[    0.380141] PGD 0
[    0.380141] Oops: 0000 [#1] SMP
[    0.380141] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.0+ #5
[    0.380141] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007
[    0.380141] task: ffff88003c9f0000 ti: ffff88003c9f8000 task.ti: ffff88003c9f8000
[    0.380141] RIP: 0010:[<ffffffff814741ef>]  [<ffffffff814741ef>] __virtscsi_set_affinity+0x4f/0x120
[    0.380141] RSP: 0000:ffff88003c9f9c08  EFLAGS: 00010256
[    0.380141] RAX: 0000000000000000 RBX: ffff88003c3a9d40 RCX: 0000000000001070
[    0.380141] RDX: 0000000000000002 RSI: 0000000000000000 RDI: 0000000000000000
[    0.380141] RBP: ffff88003c9f9c28 R08: 00000000000136c0 R09: ffff88003c801c00
[    0.380141] R10: ffffffff81475229 R11: 0000000000000008 R12: 0000000000000000
[    0.380141] R13: ffffffff81cc7ca8 R14: ffff88003cac3d40 R15: ffff88003cac37a0
[    0.380141] FS:  0000000000000000(0000) GS:ffff88003e400000(0000) knlGS:0000000000000000
[    0.380141] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[    0.380141] CR2: 0000000000000020 CR3: 0000000001c0e000 CR4: 00000000000006f0
[    0.380141] Stack:
[    0.380141]  ffff88003c3a9d40 0000000000000000 ffff88003cac3d80 ffff88003cac3d40
[    0.380141]  ffff88003c9f9c48 ffffffff814742e8 ffff88003c26d000 ffff88003c26d000
[    0.380141]  ffff88003c9f9c68 ffffffff81474321 ffff88003c26d000 ffff88003c3a9d40
[    0.380141] Call Trace:
[    0.380141]  [<ffffffff814742e8>] virtscsi_set_affinity+0x28/0x40
[    0.380141]  [<ffffffff81474321>] virtscsi_remove_vqs+0x21/0x50
[    0.380141]  [<ffffffff81475231>] virtscsi_init+0x91/0x240
[    0.380141]  [<ffffffff81365290>] ? vp_get+0x50/0x70
[    0.380141]  [<ffffffff81475544>] virtscsi_probe+0xf4/0x280
[    0.380141]  [<ffffffff81363ea5>] virtio_dev_probe+0xe5/0x140
[    0.380141]  [<ffffffff8144c669>] driver_probe_device+0x89/0x230
[    0.380141]  [<ffffffff8144c8ab>] __driver_attach+0x9b/0xa0
[    0.380141]  [<ffffffff8144c810>] ? driver_probe_device+0x230/0x230
[    0.380141]  [<ffffffff8144c810>] ? driver_probe_device+0x230/0x230
[    0.380141]  [<ffffffff8144ac1c>] bus_for_each_dev+0x8c/0xb0
[    0.380141]  [<ffffffff8144c499>] driver_attach+0x19/0x20
[    0.380141]  [<ffffffff8144bf28>] bus_add_driver+0x198/0x220
[    0.380141]  [<ffffffff8144ce9f>] driver_register+0x5f/0xf0
[    0.380141]  [<ffffffff81d27c91>] ? spi_transport_init+0x79/0x79
[    0.380141]  [<ffffffff8136403b>] register_virtio_driver+0x1b/0x30
[    0.380141]  [<ffffffff81d27d19>] init+0x88/0xd6
[    0.380141]  [<ffffffff81d27c18>] ? scsi_init_procfs+0x5b/0x5b
[    0.380141]  [<ffffffff81ce88a7>] do_one_initcall+0x7f/0x10a
[    0.380141]  [<ffffffff81ce8aa7>] kernel_init_freeable+0x14a/0x1de
[    0.380141]  [<ffffffff81ce8b3b>] ? kernel_init_freeable+0x1de/0x1de
[    0.380141]  [<ffffffff817dec20>] ? rest_init+0x80/0x80
[    0.380141]  [<ffffffff817dec29>] kernel_init+0x9/0xf0
[    0.380141]  [<ffffffff817e68fc>] ret_from_fork+0x7c/0xb0
[    0.380141]  [<ffffffff817dec20>] ? rest_init+0x80/0x80
[    0.380141] RIP  [<ffffffff814741ef>] __virtscsi_set_affinity+0x4f/0x120
[    0.380141]  RSP <ffff88003c9f9c08>
[    0.380141] CR2: 0000000000000020
[    0.380141] ---[ end trace 8074b70c3d5e1d73 ]---
[    0.475018] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
[    0.475018]
[    0.475068] Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff)
[    0.475068] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009

[jejb: checkpatch fixes]
Signed-off-by: Fam Zheng <famz@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_balloon: don't softlockup on huge balloon changes.

commit 1f74ef0f2d7d692fcd615621e0e734c3e7771413 upstream.

When adding or removing 100G from a balloon:

    BUG: soft lockup - CPU#0 stuck for 22s! [vballoon:367]

We have a wait_event_interruptible(), but the condition is always true
(more ballooning to do) so we don't ever sleep.  We also have a
wait_event() for the host to ack, but that is also always true as QEMU
is synchronous for balloon operations.

Reported-by: Gopesh Kumar Chaudhary <gopchaud@in.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Hibernate: Flush TLB entries in swsusp_arch_resume()

commit c14af233fbe279d0e561ecf84f1208b1bae087ef upstream.

The original MIPS hibernate code flushes cache and TLB entries in
swsusp_arch_resume(). But they are removed in Commit 44eeab67416711
(MIPS: Hibernation: Remove SMP TLB and cacheflushing code.). A cross-
CPU flush is surely unnecessary because all but the local CPU have
already been disabled. But a local flush (at least the TLB flush) is
needed. When we do hibernation on Loongson-3 with an E1000E NIC, it is
very easy to produce a kernel panic (kernel page fault, or unaligned
access). The root cause is E1000E driver use vzalloc_node() to allocate
pages, the stale TLB entries of the booting kernel will be misused by
the resumed target kernel.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6643/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: KVM: Pass reserved instruction exceptions to guest

commit 15505679362270d02c449626385cb74af8905514 upstream.

Previously a reserved instruction exception while in guest code would
cause a KVM internal error if kvm_mips_handle_ri() didn't recognise the
instruction (including a RDHWR from an unrecognised hardware register).

However the guest OS should really have the opportunity to catch the
exception so that it can take the appropriate actions such as sending a
SIGILL to the guest user process or emulating the instruction itself.

Therefore in these cases emulate a guest RI exception and only return
EMULATE_FAIL if that fails, being careful to revert the PC first in case
the exception occurred in a branch delay slot in which case the PC will
already point to the branch target.

Also turn the printk messages relating to these cases into kvm_debug
messages so that they aren't usually visible.

This allows crashme to run in the guest without killing the entire VM.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: ioapic: fix assignment of ioapic->rtc_status.pending_eoi (CVE-2014-0155)

commit 5678de3f15010b9022ee45673f33bcfc71d47b60 upstream.

QE reported that they got the BUG_ON in ioapic_service to trigger.
I cannot reproduce it, but there are two reasons why this could happen.

The less likely but also easiest one, is when kvm_irq_delivery_to_apic
does not deliver to any APIC and returns -1.

Because irqe.shorthand == 0, the kvm_for_each_vcpu loop in that
function is never reached.  However, you can target the similar loop in
kvm_irq_delivery_to_apic_fast; just program a zero logical destination
address into the IOAPIC, or an out-of-range physical destination address.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 7840/1: LPAE: don't reject mapping /dev/mem above 4GB

commit 3159f372354e8e1f5dee714663d705dd2c7e0759 upstream.

With LPAE enabled, physical address space is larger than 4GB. Allow mapping any
part of it via /dev/mem by using PHYS_MASK to determine valid range.

PHYS_MASK covers 40 bits with LPAE enabled and 32 bits otherwise.

Reported-by: Vassili Karpov <av1474@comtv.ru>
Signed-off-by: Sergey Dyasly <dserrg@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: hujianyang <hujianyang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iser-target: Add missing se_cmd put for WRITE_PENDING in tx_comp_err

commit 03e7848a64ed535a30f5d7fc6dede2d5a6a2534b upstream.

This patch fixes a bug where outstanding RDMA_READs with WRITE_PENDING
status require an extra target_put_sess_cmd() in isert_put_cmd() code
when called from isert_cq_tx_comp_err() + isert_cq_drain_comp_llist()
context during session shutdown.

The extra kref PUT is required so that transport_generic_free_cmd()
invokes the last target_put_sess_cmd() -> target_release_cmd_kref(),
which will complete(&se_cmd->cmd_wait_comp) the outstanding se_cmd
descriptor with WRITE_PENDING status, and awake the completion in
target_wait_for_sess_cmds() to invoke TFO->release_cmd().

The bug was manifesting itself in target_wait_for_sess_cmds() where
a se_cmd descriptor with WRITE_PENDING status would end up sleeping
indefinately.

Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

floppy: don't write kernel-only members to FDRAWCMD ioctl output

commit 2145e15e0557a01b9195d1c7199a1b92cb9be81f upstream.

Do not leak kernel-only floppy_raw_cmd structure members to userspace.
This includes the linked-list pointer and the pointer to the allocated
DMA space.

Signed-off-by: Matthew Daley <mattd@bugfuzz.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

floppy: ignore kernel-only members in FDRAWCMD ioctl input

commit ef87dbe7614341c2e7bfe8d32fcb7028cc97442c upstream.

Always clear out these floppy_raw_cmd struct members after copying the
entire structure from userspace so that the in-kernel version is always
valid and never left in an interdeterminate state.

Signed-off-by: Matthew Daley <mattd@bugfuzz.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

n_tty: Fix n_tty_write crash when echoing in raw mode

commit 4291086b1f081b869c6d79e5b7441633dc3ace00 upstream.

The tty atomic_write_lock does not provide an exclusion guarantee for
the tty driver if the termios settings are LECHO & !OPOST.  And since
it is unexpected and not allowed to call TTY buffer helpers like
tty_insert_flip_string concurrently, this may lead to crashes when
concurrect writers call pty_write. In that case the following two
writers:
* the ECHOing from a workqueue and
* pty_write from the process
race and can overflow the corresponding TTY buffer like follows.

If we look into tty_insert_flip_string_fixed_flag, there is:
  int space = __tty_buffer_request_room(port, goal, flags);
  struct tty_buffer *tb = port->buf.tail;
  ...
  memcpy(char_buf_ptr(tb, tb->used), chars, space);
  ...
  tb->used += space;

so the race of the two can result in something like this:
              A                                B
__tty_buffer_request_room
                                  __tty_buffer_request_room
memcpy(buf(tb->used), ...)
tb->used += space;
                                  memcpy(buf(tb->used), ...) ->BOOM

B's memcpy is past the tty_buffer due to the previous A's tb->used
increment.

Since the N_TTY line discipline input processing can output
concurrently with a tty write, obtain the N_TTY ldisc output_lock to
serialize echo output with normal tty writes.  This ensures the tty
buffer helper tty_insert_flip_string is not called concurrently and
everything is fine.

Note that this is nicely reproducible by an ordinary user using
forkpty and some setup around that (raw termios + ECHO). And it is
present in kernels at least after commit
d945cb9cce20ac7143c2de8d88b187f62db99bdc (pty: Rework the pty layer to
use the normal buffering logic) in 2.6.31-rc3.

js: add more info to the commit log
js: switch to bool
js: lock unconditionally
js: lock only the tty->ops->write call

References: CVE-2014-0196
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: 8250_core.c Bug fix for Exar chips.

commit b790f210fe8423eff881b2a8a93ba5dbc45534d0 upstream.

The sleep function was updated to put the serial port to sleep only when necessary.
This appears to resolve the errant behavior of the driver as described in
Kernel Bug 61961 – "My Exar Corp. XR17C/D152 Dual PCI UART modem does not
work with 3.8.0".

Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/hvc: don't free hvc_console_setup after init

commit 501fed45b7e8836ee9373f4d31e2d85e3db6103a upstream.

When 'console=hvc0' is specified to the kernel parameter in x86 KVM guest,
hvc console is setup within a kthread. However, that will cause SEGV
and the boot will fail when the driver is builtin to the kernel,
because currently hvc_console_setup() is annotated with '__init'. This
patch removes '__init' to boot the guest successfully with 'console=hvc0'.

Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge remote-tracking branch 'lsk/v3.10/topic/of' into linux-linaro-lsk

clk: of: helper for determining number of parent clocks

Walks the "clocks" array of parent clock phandles and returns the
number.

Signed-off-by: Mike Turquette <mturquette@linaro.org>
(cherry picked from commit f61027426a5bc7093aa8359a411b053a35bb4b68)

Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

Merge remote-tracking branch 'lsk/v3.10/topic/usb' into linux-linaro-lsk

Merge remote-tracking branch 'lsk/v3.10/topic/netdrv' into linux-linaro-lsk

net: smsc911x: don't artificially limit build

Currently the SMSC911X driver may only be built for a specific set of
architectures, being limited to do so by a Kconfig depends line. This
means that if a platform wishes to use the driver, its architecture must
be added to the list explicitly, introducing pointless churn.

This may have been due to the driver's use of the {read,write}s{b,w,l}
functions, which have since been replaced with the more standard
io{read,write}{8,16,32}_rep. We can instead depend on HAS_IOMEM, which
should prevent build issues while allowing the driver to be built for
currently unlisted architectures, including x86 and arm64.

This patch removes the explicit list of architectures from the driver's
depend line, and replaces it with a dependency on HAS_IOMEM.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit f1238261891bea67da845688b7684a3444c61bd9)
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

USB: OHCI: remove bogus #error

The OHCI host controller driver can be built standalone now,
without enabling any of the available bus glue drivers, so
there is not really a reason to error out here:

drivers/usb/host/ohci-hcd.c:1258: error:
 #error "missing bus glue for ohci-hcd"  #error "missing bus glue for ohci-hcd"

This follows the same change done in ehci recently as 843e56c0
"USB: EHCI: remove bogus #error" and hopefully avoids future
merge conflicts in this list.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 358e91175cac9398b152ad9adc2391ebce34011c)
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Conflicts:
drivers/usb/host/ohci-hcd.c
Signed-off-by: Mark Brown <broonie@linaro.org>