--- /dev/null
+#ifndef REALTEK_POWER_SEQUENCE_8821
+#define REALTEK_POWER_SEQUENCE_8821
+
+#include "HalPwrSeqCmd.h"
+
+/*
+ Check document WM-20130516-JackieLau-RTL8821A_Power_Architecture-R10.vsd
+ There are 6 HW Power States:
+ 0: POFF--Power Off
+ 1: PDN--Power Down
+ 2: CARDEMU--Card Emulation
+ 3: ACT--Active Mode
+ 4: LPS--Low Power State
+ 5: SUS--Suspend
+
+ The transision from different states are defined below
+ TRANS_CARDEMU_TO_ACT
+ TRANS_ACT_TO_CARDEMU
+ TRANS_CARDEMU_TO_SUS
+ TRANS_SUS_TO_CARDEMU
+ TRANS_CARDEMU_TO_PDN
+ TRANS_ACT_TO_LPS
+ TRANS_LPS_TO_ACT
+
+ TRANS_END
+*/
+#define RTL8821A_TRANS_CARDEMU_TO_ACT_STEPS 25
+#define RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS 15
+#define RTL8821A_TRANS_CARDEMU_TO_SUS_STEPS 15
+#define RTL8821A_TRANS_SUS_TO_CARDEMU_STEPS 15
+#define RTL8821A_TRANS_CARDDIS_TO_CARDEMU_STEPS 15
+#define RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS 15
+#define RTL8821A_TRANS_PDN_TO_CARDEMU_STEPS 15
+#define RTL8821A_TRANS_ACT_TO_LPS_STEPS 15
+#define RTL8821A_TRANS_LPS_TO_ACT_STEPS 15
+#define RTL8821A_TRANS_END_STEPS 1
+
+
+#define RTL8821A_TRANS_CARDEMU_TO_ACT \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \
+ {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/ \
+ {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/ \
+ {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT4 | BIT3 | BIT2), 0},/* disable SW LPS 0x04[10]=0 and WLSUS_EN 0x04[12:11]=0*/ \
+ {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 , BIT0},/* Disable USB suspend */ \
+ {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1 power ready*/ \
+ {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 , 0},/* Enable USB suspend */ \
+ {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset 0x04[16]=1*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]=0*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT4 | BIT3), 0},/* disable WL suspend*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0},/**/ \
+ {0x004F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*0x4C[24] = 0x4F[0] = 1, switch DPDT_SEL_P output from WL BB */\
+ {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT5 | BIT4), (BIT5 | BIT4)},/*0x66[13] = 0x67[5] = 1, switch for PAPE_G/PAPE_A from WL BB ; 0x66[12] = 0x67[4] = 1, switch LNAON from WL BB */\
+ {0x0025, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6, 0},/*anapar_mac<118> , 0x25[6]=0 by wlan single function*/\
+ {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/*Enable falling edge triggering interrupt*/\
+ {0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/*Enable GPIO9 interrupt mode*/\
+ {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Enable GPIO9 input mode*/\
+ {0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*Enable HSISR GPIO[C:0] interrupt*/\
+ {0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/*Enable HSISR GPIO9 interrupt*/\
+ {0x007A, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3A},/*0x7A = 0x3A start BT*/\
+ {0x002E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF , 0x82 },/* 0x2C[23:12]=0x820 ; XTAL trim */ \
+ {0x0010, PWR_CUT_A_MSK , PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6 , BIT6 },/* 0x10[6]=1 ; MP·s¼W¹ï©ó0x2Cªº±±¨îÅv¡A¶·§â0x10[6]³]¬°1¤~¯àÅýWLAN±±¨î */ \
+
+
+#define RTL8821A_TRANS_ACT_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \
+ {0x004F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*0x4C[24] = 0x4F[0] = 0, switch DPDT_SEL_P output from register 0x65[2] */\
+ {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Enable rising edge triggering interrupt*/ \
+ {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset 0x04[16]=1*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
+ {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5}, /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/ \
+ {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/ \
+
+
+#define RTL8821A_TRANS_CARDEMU_TO_SUS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4 | BIT3, (BIT4 | BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
+ {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
+ {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3 | BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/
+
+#define RTL8821A_TRANS_SUS_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
+ {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
+
+#define RTL8821A_TRANS_CARDEMU_TO_CARDDIS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07 = 0x20 , SOP option to disable BG/MB*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2}, /*0x04[10] = 1, enable SW LPS*/ \
+ {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/ \
+ {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/
+
+#define RTL8821A_TRANS_CARDDIS_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
+ {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\
+ {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \
+ {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/
+
+
+#define RTL8821A_TRANS_CARDEMU_TO_PDN \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
+ {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK | PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \
+ {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/
+
+#define RTL8821A_TRANS_PDN_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/
+
+#define RTL8821A_TRANS_ACT_TO_LPS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \
+ {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \
+ {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/ \
+ {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/ \
+ {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \
+ {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/ \
+ {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/ \
+
+
+#define RTL8821A_TRANS_LPS_TO_ACT \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
+ {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
+ {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
+ {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*. 0x08[4] = 0 switch TSF to 40M*/\
+ {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0 TSF in 40M*/\
+ {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6 | BIT7, 0}, /*. 0x29[7:6] = 2b'00 enable BB clock*/\
+ {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1*/\
+ {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1 | BIT0, BIT1 | BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\
+ {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/
+
+#define RTL8821A_TRANS_END \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0},
+
+
+ extern WLAN_PWR_CFG rtl8821A_power_on_flow[RTL8821A_TRANS_CARDEMU_TO_ACT_STEPS + RTL8821A_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8821A_radio_off_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + RTL8821A_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8821A_card_disable_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS + RTL8821A_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8821A_card_enable_flow[RTL8821A_TRANS_CARDDIS_TO_CARDEMU_STEPS + RTL8821A_TRANS_CARDEMU_TO_ACT_STEPS + RTL8821A_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8821A_suspend_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + RTL8821A_TRANS_CARDEMU_TO_SUS_STEPS + RTL8821A_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8821A_resume_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + RTL8821A_TRANS_CARDEMU_TO_SUS_STEPS + RTL8821A_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8821A_hwpdn_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS + RTL8821A_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8821A_enter_lps_flow[RTL8821A_TRANS_ACT_TO_LPS_STEPS + RTL8821A_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8821A_leave_lps_flow[RTL8821A_TRANS_LPS_TO_ACT_STEPS + RTL8821A_TRANS_END_STEPS];
+
+#endif
projects / firefly-linux-kernel-4.4.55.git / blobdiff