/*
+ * Copyright (c) 2015~2017 Fuzhou Rockchip Electronics Co., Ltd
+ *
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
*/
#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/input/input.h>
#include "rk3288.dtsi"
/ {
- memory {
- device_type = "memory";
- reg = <0x0 0x80000000>;
+ chosen {
+ bootargs = "earlycon=uart8250,mmio32,0xff690000 swiotlb=1";
};
- backlight: backlight {
- compatible = "pwm-backlight";
- brightness-levels = <
- 0 1 2 3 4 5 6 7
- 8 9 10 11 12 13 14 15
- 16 17 18 19 20 21 22 23
- 24 25 26 27 28 29 30 31
- 32 33 34 35 36 37 38 39
- 40 41 42 43 44 45 46 47
- 48 49 50 51 52 53 54 55
- 56 57 58 59 60 61 62 63
- 64 65 66 67 68 69 70 71
- 72 73 74 75 76 77 78 79
- 80 81 82 83 84 85 86 87
- 88 89 90 91 92 93 94 95
- 96 97 98 99 100 101 102 103
- 104 105 106 107 108 109 110 111
- 112 113 114 115 116 117 118 119
- 120 121 122 123 124 125 126 127
- 128 129 130 131 132 133 134 135
- 136 137 138 139 140 141 142 143
- 144 145 146 147 148 149 150 151
- 152 153 154 155 156 157 158 159
- 160 161 162 163 164 165 166 167
- 168 169 170 171 172 173 174 175
- 176 177 178 179 180 181 182 183
- 184 185 186 187 188 189 190 191
- 192 193 194 195 196 197 198 199
- 200 201 202 203 204 205 206 207
- 208 209 210 211 212 213 214 215
- 216 217 218 219 220 221 222 223
- 224 225 226 227 228 229 230 231
- 232 233 234 235 236 237 238 239
- 240 241 242 243 244 245 246 247
- 248 249 250 251 252 253 254 255>;
- default-brightness-level = <128>;
- enable-gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en>;
- pwms = <&pwm0 0 1000000 PWM_POLARITY_INVERTED>;
- };
-
- panel: panel {
+ edp_panel: edp-panel {
compatible ="lg,lp079qx1-sp0v", "simple-panel";
- backlight = <&backlight>;
enable-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&lcd_cs>;
+ status = "disabled";
+
ports {
panel_in: port {
panel_in_edp: endpoint {
lvds_panel: lvds_panel {
compatible ="auo,b101ew05","simple-panel";
- backlight = <&backlight>;
enable-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&lcd_cs>;
status = "disabled";
#clock-cells = <0>;
};
- gpio-keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- autorepeat;
-
- pinctrl-names = "default";
- pinctrl-0 = <&pwrbtn>;
-
- button@0 {
- gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
- linux,code = <116>;
- label = "GPIO Key Power";
- linux,input-type = <1>;
- gpio-key,wakeup = <1>;
- debounce-interval = <100>;
- };
+ vccadc_ref: vccadc-ref {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
/* This turns on USB vbus for both host0 (ehci) and host1 (dwc2) */
pinctrl-0 = <&rgmii_pins>;
tx_delay = <0x30>;
rx_delay = <0x10>;
+ max-speed = <100>;
status = "okay";
};
#address-cells = <1>;
#size-cells = <0>;
#sound-dai-cells = <0>;
- ddc-i2c-bus = <&i2c5>;
status = "okay";
/* Don't use vopl for HDMI */
};
};
+&saradc {
+ vref-supply = <&vccadc_ref>;
+ status = "okay";
+};
+
&sdmmc {
supports-sd;
bus-width = <4>;
};
};
-&i2c5 {
+&i2c4 {
status = "okay";
+
+ gsl3673@40 {
+ compatible = "GSL,GSL3673";
+ reg = <0x40>;
+ screen_max_x = <1536>;
+ screen_max_y = <2048>;
+ irq_gpio_number = <&gpio7 6 IRQ_TYPE_LEVEL_LOW>;
+ rst_gpio_number = <&gpio7 5 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
};
&i2s {
status = "okay";
};
-&uart1 {
- status = "okay";
-};
-
&uart2 {
status = "okay";
};
-&uart3 {
- status = "okay";
-};
-
-&uart4 {
- status = "okay";
-};
-
&vpu_service {
status = "okay";
};
};
&usb_host0_ehci {
+ rockchip-relinquish-port;
status = "okay";
};
drive-strength = <8>;
};
- backlight {
- bl_en: bl-en {
- rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
- };
- };
-
- buttons {
- pwrbtn: pwrbtn {
- rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
- };
- };
-
pmic {
pmic_int: pmic-int {
rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;