/*
+ * Copyright (c) 2015~2017 Fuzhou Rockchip Electronics Co., Ltd
+ *
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
*/
#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/input/input.h>
#include "rk3288.dtsi"
/ {
- memory {
- device_type = "memory";
- reg = <0x0 0x80000000>;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- brightness-levels = <
- 0 1 2 3 4 5 6 7
- 8 9 10 11 12 13 14 15
- 16 17 18 19 20 21 22 23
- 24 25 26 27 28 29 30 31
- 32 33 34 35 36 37 38 39
- 40 41 42 43 44 45 46 47
- 48 49 50 51 52 53 54 55
- 56 57 58 59 60 61 62 63
- 64 65 66 67 68 69 70 71
- 72 73 74 75 76 77 78 79
- 80 81 82 83 84 85 86 87
- 88 89 90 91 92 93 94 95
- 96 97 98 99 100 101 102 103
- 104 105 106 107 108 109 110 111
- 112 113 114 115 116 117 118 119
- 120 121 122 123 124 125 126 127
- 128 129 130 131 132 133 134 135
- 136 137 138 139 140 141 142 143
- 144 145 146 147 148 149 150 151
- 152 153 154 155 156 157 158 159
- 160 161 162 163 164 165 166 167
- 168 169 170 171 172 173 174 175
- 176 177 178 179 180 181 182 183
- 184 185 186 187 188 189 190 191
- 192 193 194 195 196 197 198 199
- 200 201 202 203 204 205 206 207
- 208 209 210 211 212 213 214 215
- 216 217 218 219 220 221 222 223
- 224 225 226 227 228 229 230 231
- 232 233 234 235 236 237 238 239
- 240 241 242 243 244 245 246 247
- 248 249 250 251 252 253 254 255>;
- default-brightness-level = <128>;
- enable-gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en>;
- pwms = <&pwm0 0 1000000 PWM_POLARITY_INVERTED>;
+ chosen {
+ bootargs = "earlycon=uart8250,mmio32,0xff690000 swiotlb=1";
};
- panel: panel {
+ edp_panel: edp-panel {
compatible ="lg,lp079qx1-sp0v", "simple-panel";
- backlight = <&backlight>;
enable-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&lcd_cs>;
+ status = "disabled";
+
ports {
panel_in: port {
panel_in_edp: endpoint {
};
};
- hdmi-sound {
+ sound {
compatible = "simple-audio-card";
simple-audio-card,format = "i2s";
- simple-audio-card,name = "DW-HDMI";
+ simple-audio-card,name = "rockchip,rt5640-codec";
simple-audio-card,mclk-fs = <512>;
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "MIC1", "Microphone Jack",
+ "MIC2", "Microphone Jack",
+ "Microphone Jack", "micbias1",
+ "Headphone Jack", "HPOL",
+ "Headphone Jack", "HPOR";
+
+ simple-audio-card,dai-link@0 {
+ format = "i2s";
+ cpu {
+ sound-dai = <&i2s>;
+ };
- simple-audio-card,cpu {
- sound-dai = <&i2s>;
+ codec {
+ sound-dai = <&rt5640>;
+ };
};
- simple-audio-card,codec {
- sound-dai = <&hdmi>;
+ simple-audio-card,dai-link@1 {
+ format = "i2s";
+ cpu {
+ sound-dai = <&i2s>;
+ };
+
+ codec {
+ sound-dai = <&hdmi>;
+ };
};
};
lvds_panel: lvds_panel {
compatible ="auo,b101ew05","simple-panel";
- backlight = <&backlight>;
enable-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&lcd_cs>;
status = "disabled";
#clock-cells = <0>;
};
- gpio-keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- autorepeat;
-
- pinctrl-names = "default";
- pinctrl-0 = <&pwrbtn>;
-
- button@0 {
- gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
- linux,code = <116>;
- label = "GPIO Key Power";
- linux,input-type = <1>;
- gpio-key,wakeup = <1>;
- debounce-interval = <100>;
- };
+ vccadc_ref: vccadc-ref {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
/* This turns on USB vbus for both host0 (ehci) and host1 (dwc2) */
*/
vcc_sd: sdmmc-regulator {
compatible = "regulator-fixed";
- gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc_pwr>;
regulator-name = "vcc_sd";
startup-delay-us = <100000>;
vin-supply = <&vcc_io>;
};
+
+ wireless-bluetooth {
+ compatible = "bluetooth-platdata";
+ uart_rts_gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default", "rts_gpio";
+ pinctrl-0 = <&uart0_rts>;
+ pinctrl-1 = <&uart0_gpios>;
+ BT,reset_gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+ BT,wake_gpio = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+ BT,wake_host_irq = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ wireless-wlan {
+ compatible = "wlan-platdata";
+ rockchip,grf = <&grf>;
+ wifi_chip_type = "ap6335";
+ sdio_vref = <1800>;
+ WIFI,host_wake_irq = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
};
&emmc {
status = "okay";
};
+&gmac {
+ phy-supply = <&vcc_phy>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio4 7 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ max-speed = <100>;
+ status = "okay";
+};
+
&hdmi {
#address-cells = <1>;
#size-cells = <0>;
#sound-dai-cells = <0>;
- ddc-i2c-bus = <&i2c5>;
+ status = "okay";
+
+ /* Don't use vopl for HDMI */
+ ports {
+ hdmi_in: port {
+ /delete-node/ endpoint@1;
+ };
+ };
+};
+
+&saradc {
+ vref-supply = <&vccadc_ref>;
status = "okay";
};
supports-sd;
bus-width = <4>;
cap-mmc-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
cap-sd-highspeed;
card-detect-delay = <200>;
disable-wp; /* wp not hooked up */
status = "okay";
vmmc-supply = <&vcc_sd>;
vqmmc-supply = <&vccio_sd>;
-};
-
-&gmac {
- phy-supply = <&vcc_phy>;
- phy-mode = "rgmii";
- clock_in_out = "input";
- snps,reset-gpio = <&gpio4 7 0>;
- snps,reset-active-low;
- snps,reset-delays-us = <0 10000 1000000>;
- assigned-clocks = <&cru SCLK_MAC>;
- assigned-clock-parents = <&ext_gmac>;
- pinctrl-names = "default";
- pinctrl-0 = <&rgmii_pins>;
- tx_delay = <0x30>;
- rx_delay = <0x10>;
- status = "ok";
+ supports-sd;
};
&edp_phy {
status = "okay";
ports {
+ /* Don't use vopb for eDP */
+ edp_in: port@0 {
+ /delete-node/ endpoint@0;
+ };
+
edp_out: port@1 {
reg = <1>;
#address-cells = <1>;
};
};
+&hevc_service {
+ status = "okay";
+};
+
&i2c0 {
status = "okay";
};
-&i2c5 {
+&i2c2 {
status = "okay";
+
+ rt5640: rt5640@1c {
+ #sound-dai-cells = <0>;
+ compatible = "realtek,rt5640";
+ reg = <0x1c>;
+ clocks = <&cru SCLK_I2S0_OUT>;
+ clock-names = "mclk";
+ interrupt-parent = <&gpio6>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&i2c4 {
+ status = "okay";
+
+ gsl3673@40 {
+ compatible = "GSL,GSL3673";
+ reg = <0x40>;
+ screen_max_x = <1536>;
+ screen_max_y = <2048>;
+ irq_gpio_number = <&gpio7 6 IRQ_TYPE_LEVEL_LOW>;
+ rst_gpio_number = <&gpio7 5 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
};
&i2s {
status = "okay";
};
-&wdt {
+&io_domains {
status = "okay";
+
+ sdcard-supply = <&vccio_sd>;
+ wifi-supply = <&vcc_18>;
};
-&pwm0 {
+&wdt {
status = "okay";
};
-&uart0 {
+&pwm0 {
status = "okay";
};
-&uart1 {
+&rga {
status = "okay";
};
-&uart2 {
+&sdio0 {
status = "okay";
+
+ clock-frequency = <50000000>;
+ clock-freq-min-max = <200000 50000000>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ disable-wp;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk &sdio0_int>;
+ sd-uhs-sdr104;
+ supports-sdio;
};
-&uart3 {
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts>;
status = "okay";
};
-&uart4 {
+&uart2 {
status = "okay";
};
-&vpu {
+&vpu_service {
status = "okay";
};
status = "okay";
};
+&usbphy {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ rockchip-relinquish-port;
+ status = "okay";
+};
+
+&usb_host1 {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
+
+&lvds {
+ rockchip,data-mapping = "jeida";
+ rockchip,data-width = <24>;
+ rockchip,output = "lvds";
+ rockchip,panel = <&lvds_panel>;
+ status = "disabled";
+};
+
+&vopb {
+ status = "okay";
+
+ /* Don't use vopb for eDP, save it for HDMI */
+ vopb_out: port {
+ /delete-node/ endpoint@1;
+ };
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+
+ /* Don't use vopb for HDMI, save it for eDP */
+ vopl_out: port {
+ /delete-node/ endpoint@0;
+ };
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
&pinctrl {
pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
drive-strength = <8>;
drive-strength = <8>;
};
- backlight {
- bl_en: bl-en {
- rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
- };
- };
-
- buttons {
- pwrbtn: pwrbtn {
- rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
- };
- };
-
pmic {
pmic_int: pmic-int {
rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
sdmmc {
/*
* Default drive strength isn't enough to achieve even
rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
-};
-
-&usbphy {
- status = "okay";
-};
-
-&usb_host0_ehci {
- status = "okay";
-};
-
-&usb_host1 {
- status = "okay";
-};
-
-&lvds {
- rockchip,data-mapping = "jeida";
- rockchip,data-width = <24>;
- rockchip,output = "lvds";
- rockchip,panel = <&lvds_panel>;
- status = "disabled";
-};
-
-&vopb {
- status = "okay";
-};
-
-&vopb_mmu {
- status = "okay";
-};
-&vopl {
- status = "okay";
-};
-
-&vopl_mmu {
- status = "okay";
+ wireless-bluetooth {
+ uart0_gpios: uart0-gpios {
+ rockchip,pins = <4 19 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
};
projects / firefly-linux-kernel-4.4.55.git / blobdiff