3 #include <dt-bindings/interrupt-controller/arm-gic.h>
4 #include <dt-bindings/rkfb/rk_fb.h>
6 #include "../../../arm/boot/dts/lcd-ld089wu1-mipi.dtsi"
9 bootargs = "earlyprintk=uart8250-32bit,0xff690000";
13 compatible = "wlan-platdata";
15 rockchip,grf = <&grf>;
17 /* wifi_chip_type - wifi chip define
18 * ap6210, ap6330, ap6335
19 * rtl8188eu, rtl8723bs, rtl8723bu
22 wifi_chip_type = "ap6210";
24 sdio_vref = <1800>; //1800mv or 3300mv
25 power_pmu_regulator = "rk818_ldo8_reg";
26 power_pmu_enable_level = <1>; //1->HIGH, 0->LOW
27 vref_pmu_regulator = "rk818_ldo8_reg";
28 vref_pmu_enable_level = <1>; //1->HIGH, 0->LOW
30 WIFI,poweren_gpio = <&gpio3 GPIO_A4 GPIO_ACTIVE_HIGH>;
31 WIFI,host_wake_irq = <&gpio3 GPIO_A6 GPIO_ACTIVE_HIGH>;
37 compatible = "bluetooth-platdata";
38 uart_rts_gpios = <&gpio2 GPIO_D3 GPIO_ACTIVE_LOW>;
39 pinctrl-names = "default","rts_gpio";
40 pinctrl-0 = <&uart0_rts>;
41 pinctrl-1 = <&uart0_rts_gpio>;
43 BT,power_gpio = <&gpio3 GPIO_A3 GPIO_ACTIVE_HIGH>;
44 BT,reset_gpio = <&gpio3 GPIO_A5 GPIO_ACTIVE_HIGH>;
45 BT,wake_gpio = <&gpio3 GPIO_A2 GPIO_ACTIVE_HIGH>;
46 BT,wake_host_irq = <&gpio3 GPIO_A7 GPIO_ACTIVE_HIGH>;
52 compatible = "hall_och165t";
53 type = <SENSOR_TYPE_HALL>;
54 irq-gpio = <&gpio0 GPIO_C0 IRQ_TYPE_EDGE_BOTH>;
57 backlight: backlight {
58 compatible = "pwm-backlight";
59 pwms = <&pwm0 0 25000>;
60 brightness-levels = <0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
61 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
62 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
63 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87
64 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109
65 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
66 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147
67 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166
68 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185
69 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204
70 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
71 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242
72 243 244 245 246 247 248 249 250 251 252 253 254 255>;
73 default-brightness-level = <128>;
74 enable-gpios = <&gpio0 GPIO_C4 GPIO_ACTIVE_HIGH>;
78 compatible = "rockchip_pwm_regulator";
79 pwms = <&pwm1 0 2000>;
81 rockchip,pwm_voltage_map= <925000 950000 975000 1000000 1025000 1050000 1075000 1100000 1125000 1150000 1175000 1200000 1225000 1250000 1275000 1300000 1325000 1350000 1375000 1400000>;
82 rockchip,pwm_voltage= <1000000>;
83 rockchip,pwm_min_voltage= <925000>;
84 rockchip,pwm_max_voltage= <1400000>;
85 rockchip,pwm_suspend_voltage= <950000>;
86 rockchip,pwm_coefficient= <475>;
90 pwm_reg0: regulator@0 {
91 regulator-compatible = "pwm_dcdc1";
92 regulator-name= "vdd_logic";
93 regulator-min-microvolt = <925000>;
94 regulator-max-microvolt = <1400000>;
101 codec_hdmi_i2s: codec-hdmi-i2s {
102 compatible = "hdmi-i2s";
105 codec_hdmi_spdif: codec-hdmi-spdif {
106 compatible = "hdmi-spdif";
110 compatible = "rockchip-hdmi-i2s";
113 audio-codec = <&codec_hdmi_i2s>;
114 audio-controller = <&i2s0>;
120 rockchip-hdmi-spdif {
121 compatible = "rockchip-hdmi-spdif";
124 audio-codec = <&codec_hdmi_spdif>;
125 audio-controller = <&spdif>;
131 compatible = "rockchip-es8316";
134 audio-codec = <&es8316>;
135 audio-controller = <&i2s0>;
142 compatible = "rockchip,rk3368-io-voltage-domain";
143 rockchip,grf = <&grf>;
144 rockchip,pmugrf = <&pmugrf>;
147 gpio30-supply = <&rk818_dcdc4_reg>; /*APIO1_VDD*/
148 wifi-supply = <&rk818_ldo8_reg>; /*APIO2_VDD*/
149 audio-supply = <&rk818_dcdc4_reg>; /*APIO3_VDD*/
150 gpio1830-supply = <&rk818_dcdc4_reg>; /*ADIO4_VDD*/
151 sdcard-supply = <&rk818_ldo9_reg>; /*SDMMC_VDD*/
154 pmu-supply = <&rk818_ldo5_reg>; /*PMUIO_VDD*/
155 vop-supply = <&rk818_ldo5_reg>; /*LCDC_VDD*/
160 tsadc-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
161 //tsadc-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
166 //used for init some gpio
167 init-gpios = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH>;
171 rockchip,pins = <0 GPIO_C7 RK_FUNC_GPIO &pcfg_pull_down>;
174 rockchip,pins = <0 GPIO_A3 RK_FUNC_3 &pcfg_pull_none>;
177 rockchip,pins = <0 GPIO_C2 RK_FUNC_GPIO &pcfg_pull_down>;
180 rockchip,pins = <0 GPIO_C3 RK_FUNC_GPIO &pcfg_pull_down>;
184 rockchip,pins = <0 GPIO_C1 RK_FUNC_GPIO &pcfg_pull_up>;
192 status = "disabled"; // used nand set "disabled" ,used emmc set "okay"
196 status = "okay"; // used nand set "disabled" ,used emmc set "okay"
200 clock-frequency = <150000000>;
201 clock-freq-min-max = <400000 150000000>;
208 supports-DDR_MODE; //you should set the two value in your project. only close in RK3288-SDK board.
212 keep-power-in-suspend;
219 clock-frequency = <50000000>;
220 clock-freq-min-max = <400000 50000000>;
224 card-detect-delay = <200>;
227 keep-power-in-suspend;
229 vmmc-supply = <&rk818_ldo1_reg>;
234 clock-frequency = <50000000>;
235 clock-freq-min-max = <200000 50000000>;
239 keep-power-in-suspend;
270 dma-names = "!tx", "!rx";
271 pinctrl-0 = <&uart0_xfer &uart0_cts>;
277 compatible = "silergy,syr82x";
281 #address-cells = <1>;
283 syr827_dc1: regulator@0 {
285 regulator-compatible = "syr82x_dcdc1";
286 regulator-name = "vdd_arm";
287 regulator-min-microvolt = <712500>;
288 regulator-max-microvolt = <1500000>;
291 regulator-initial-mode = <0x2>;
292 regulator-initial-state = <3>;
293 regulator-state-mem {
294 regulator-state-mode = <0x2>;
295 regulator-state-disabled;
296 regulator-state-uv = <900000>;
302 compatible = "silergy,syr82x";
306 #address-cells = <1>;
308 syr828_dc1: regulator@0 {
310 regulator-compatible = "syr82x_dcdc1";
311 regulator-name = "vdd_gpu";
312 regulator-min-microvolt = <712500>;
313 regulator-max-microvolt = <1500000>;
316 regulator-initial-mode = <0x2>;
317 regulator-initial-state = <3>;
318 regulator-state-mem {
319 regulator-state-mode = <0x2>;
320 regulator-state-enabled;
321 regulator-state-uv = <900000>;
330 compatible = "rockchip,rk818";
332 ocv_table = <3400 3650 3693 3707 3731 3749 3760
333 3770 3782 3796 3812 3829 3852 3882
334 3915 3951 3981 4047 4086 4132 4182>;
335 design_capacity = <8650>;
336 design_qmax = <8800>;
337 max_overcharge = <100>;
339 max_input_currentmA = <2000>;
340 max_chrg_currentmA = <1800>;
341 max_charge_voltagemV = <4200>;
342 max_bat_voltagemV = <4200>;
343 sleep_enter_current = <600>;
344 sleep_exit_current = <600>;
345 power_off_thresd = <3400>;
346 chrg_diff_voltagemV = <0>;
347 support_usb_adp = <1>;
348 support_dc_adp = <1>;
349 dc_det_gpio = <&gpio0 GPIO_C1 GPIO_ACTIVE_LOW>;
357 compatible = "es8316";
359 spk-con-gpio = <&gpio0 GPIO_C3 GPIO_ACTIVE_HIGH>;
360 hp-det-gpio = <&gpio0 GPIO_C7 GPIO_ACTIVE_HIGH>;
368 compatible = "goodix,gt9xx";
370 touch-gpio = <&gpio0 GPIO_B4 IRQ_TYPE_LEVEL_LOW>;
371 reset-gpio = <&gpio0 GPIO_B3 GPIO_ACTIVE_HIGH>;
384 mpu6500_acc:mpu_acc@68{
385 compatible = "mpu6500_acc";
388 poll_delay_ms = <30>;
389 type = <SENSOR_TYPE_ACCEL>;
400 rockchip,disp-mode = <NO_DUAL>;
401 rockchip,uboot-logo-on = <0>;
406 display-timings = <&disp_timings>;
411 backlight = <&backlight>;
412 rockchip,mirror = <NO_MIRROR>;
413 rockchip,cabc_mode = <0>;
414 rockchip,fb-win-map = <FB_DEFAULT_ORDER>;
415 power_ctr: power_ctr {
416 rockchip,debug = <0>;
418 rockchip,power_type = <GPIO>;
419 gpios = <&gpio0 GPIO_C6 GPIO_ACTIVE_HIGH>;
420 rockchip,delay = <120>;
424 rockchip,power_type = <GPIO>;
425 gpios = <&gpio0 GPIO_C5 GPIO_ACTIVE_HIGH>;
426 rockchip,delay = <10>;
430 rockchip,power_type = <GPIO>;
431 gpios = <&gpio3 GPIO_D6 GPIO_ACTIVE_HIGH>;
432 rockchip,delay = <5>;
446 compatible = "rockchip_headset";
447 headset_gpio = <&gpio0 GPIO_C7 GPIO_ACTIVE_LOW>;
448 pinctrl-names = "default";
449 pinctrl-0 = <&gpio0_c7>;//gpio0_c7
450 io-channels = <&adc 2>;
453 hook_down_type = ; //interrupt hook key down status
458 compatible = "rockchip,key";
459 io-channels = <&adc 1>;
464 rockchip,adc_value = <1>;
469 label = "volume down";
470 rockchip,adc_value = <170>;
474 gpios = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
490 &clk_core_b_dvfs_table {
506 &clk_core_l_dvfs_table {
520 &clk_gpu_dvfs_table {
530 &clk_ddr_dvfs_table {
546 SYS_STATUS_NORMAL 528000
547 SYS_STATUS_SUSPEND 192000
548 SYS_STATUS_VIDEO_1080P 300000
549 SYS_STATUS_VIDEO_4K 600000
550 SYS_STATUS_PERFORMANCE 792000
551 SYS_STATUS_DUALVIEW 600000
552 SYS_STATUS_BOOST 400000
553 SYS_STATUS_ISP 533000
566 host_drv_gpio = <&gpio0 GPIO_A4 GPIO_ACTIVE_LOW>;
567 otg_drv_gpio = <&gpio0 GPIO_D1 GPIO_ACTIVE_LOW>;
568 rockchip,remote_wakeup;
569 rockchip,usb_irq_wakeup;
572 /include/ "../../../arm/boot/dts/rk818.dtsi"
574 gpios =<&gpio0 GPIO_A1 GPIO_ACTIVE_HIGH>,<&gpio0 GPIO_A0 GPIO_ACTIVE_LOW>;
575 rk818,system-power-controller;
576 pinctrl-names = "dc_det";
577 pinctrl-0 = <&gpio0_c1>;
580 rk818_dcdc1_reg: regulator@0{
581 regulator-name= "vdd_arm";/*vcc arm*/
582 regulator-min-microvolt = <700000>;/*<725000>;*/
583 regulator-max-microvolt = <1500000>;
584 regulator-initial-mode = <0x2>;
585 regulator-initial-state = <3>;
586 regulator-state-mem {
587 regulator-state-mode = <0x2>;
588 regulator-state-disabled;
589 regulator-state-uv =<900000>;
593 rk818_dcdc2_reg: regulator@1 {
594 regulator-name= "vdd_logic";/*vcc gpu*/
595 regulator-min-microvolt = <700000>;
596 regulator-max-microvolt = <1200000>;
597 regulator-initial-mode = <0x2>;
598 regulator-initial-state = <3>;
599 regulator-state-mem {
600 regulator-state-mode = <0x2>;
601 regulator-state-enabled;
602 regulator-state-uv = <1200000>;
606 rk818_dcdc3_reg: regulator@2 {
607 regulator-name= "vcc_ddr";
608 regulator-min-microvolt = <1200000>;
609 regulator-max-microvolt = <1200000>;
610 regulator-initial-mode = <0x2>;
611 regulator-initial-state = <3>;
612 regulator-state-mem {
613 regulator-state-mode = <0x2>;
614 regulator-state-enabled;
615 regulator-state-uv = <1200000>;
619 rk818_dcdc4_reg: regulator@3 {
620 regulator-name= "vccio";
621 regulator-min-microvolt = <3300000>;
622 regulator-max-microvolt = <3300000>;
623 regulator-initial-mode = <0x2>;
624 regulator-initial-state = <3>;
625 regulator-state-mem {
626 regulator-state-mode = <0x2>;
627 regulator-state-enabled;
628 regulator-state-uv = <3000000>;
632 rk818_ldo1_reg: regulator@4 {
633 regulator-name= "vcc_codec";
634 regulator-min-microvolt = <3300000>;
635 regulator-max-microvolt = <3300000>;
636 regulator-initial-state = <3>;
637 regulator-state-mem {
638 regulator-state-enabled;
639 regulator-state-uv = <3300000>;
643 rk818_ldo2_reg: regulator@5 {
644 regulator-name= "vcc_tp";
645 regulator-min-microvolt = <3300000>;
646 regulator-max-microvolt = <3300000>;
647 regulator-initial-state = <3>;
648 regulator-state-mem {
649 regulator-state-enabled;
650 regulator-state-uv = <3300000>;
654 rk818_ldo3_reg: regulator@6 {
655 regulator-name= "vdd_10";
656 regulator-min-microvolt = <1000000>;
657 regulator-max-microvolt = <1000000>;
658 regulator-initial-state = <3>;
659 regulator-state-mem {
660 regulator-state-enabled;
661 regulator-state-uv = <1000000>;
665 rk818_ldo4_reg:regulator@7 {
666 regulator-name= "vcc18_lcd";
667 regulator-min-microvolt = <1800000>;
668 regulator-max-microvolt = <1800000>;
669 regulator-initial-state = <3>;
670 regulator-state-mem {
671 regulator-state-disabled;
672 regulator-state-uv = <1800000>;
676 rk818_ldo5_reg: regulator@8 {
677 regulator-name= "vccio_pmu";
678 regulator-min-microvolt = <1800000>;
679 regulator-max-microvolt = <1800000>;
680 regulator-initial-state = <3>;
681 regulator-state-mem {
682 regulator-state-enabled;
683 regulator-state-uv = <1800000>;
687 rk818_ldo6_reg: regulator@9 {
688 regulator-name= "vdd10_lcd";
689 regulator-min-microvolt = <1000000>;
690 regulator-max-microvolt = <1000000>;
691 regulator-initial-state = <3>;
692 regulator-state-mem {
693 regulator-state-disabled;
694 regulator-state-uv = <1000000>;
698 rk818_ldo7_reg: regulator@10 {
699 regulator-name= "vcc_18";
700 regulator-min-microvolt = <1800000>;
701 regulator-max-microvolt = <1800000>;
702 regulator-initial-state = <3>;
703 regulator-state-mem {
704 regulator-state-enabled;
705 regulator-state-uv = <1800000>;
709 rk818_ldo8_reg: regulator@11 {
710 regulator-name= "vccio_wl";
711 regulator-min-microvolt = <1800000>;
712 regulator-max-microvolt = <1800000>;
713 regulator-initial-state = <3>;
714 regulator-state-mem {
715 regulator-state-enabled;
716 regulator-state-uv = <1800000>;
720 rk818_ldo9_reg: regulator@12 {
721 regulator-name= "vcc_sd";
722 regulator-min-microvolt = <1800000>;
723 regulator-max-microvolt = <3300000>;
724 regulator-initial-state = <3>;
725 regulator-state-mem {
726 regulator-state-enabled;
727 regulator-state-uv = <3300000>;
731 rk818_ldo10_reg: regulator@13 {
732 regulator-name= "rk818_ldo10";
733 regulator-state-mem {
734 regulator-state-disabled;
741 reg = <0x00000000 0x00000000>; /* 0MB */