firefly-linux-kernel-4.4.55.git
14 years agonet: make netpoll_rx return bool for !CONFIG_NETPOLL
John W. Linville [Tue, 10 Aug 2010 23:24:41 +0000 (16:24 -0700)]
net: make netpoll_rx return bool for !CONFIG_NETPOLL

"netpoll: Use 'bool' for netpoll_rx() return type." missed the case when
CONFIG_NETPOLL is disabled.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Tue, 10 Aug 2010 22:59:38 +0000 (15:59 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

14 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluet...
John W. Linville [Tue, 10 Aug 2010 18:55:10 +0000 (14:55 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/holtmann/bluetooth-2.6

14 years agoBluetooth: Use 3-DH5 payload size for default ERTM max PDU size
Mat Martineau [Thu, 5 Aug 2010 22:54:27 +0000 (15:54 -0700)]
Bluetooth: Use 3-DH5 payload size for default ERTM max PDU size

The previous value of 672 for L2CAP_DEFAULT_MAX_PDU_SIZE is based on
the default L2CAP MTU.  That default MTU is calculated from the size
of two DH5 packets, minus ACL and L2CAP b-frame header overhead.

ERTM is used with newer basebands that typically support larger 3-DH5
packets, and i-frames and s-frames have more header overhead.  With
clean RF conditions, basebands will typically attempt to use 1021-byte
3-DH5 packets for maximum throughput.  Adjusting for 2 bytes of ACL
headers plus 10 bytes of worst-case L2CAP headers yields 1009 bytes
of payload.

This PDU size imposes less overhead for header bytes and gives the
baseband the option to choose 3-DH5 packets, but is small enough for
ERTM traffic to interleave well with other L2CAP or SCO data.
672-byte payloads do not allow the most efficient over-the-air
packet choice, and cannot achieve maximum throughput over BR/EDR.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
14 years agoBluetooth: Fix incorrect setting of remote_tx_win for L2CAP ERTM
Mat Martineau [Thu, 5 Aug 2010 22:54:23 +0000 (15:54 -0700)]
Bluetooth: Fix incorrect setting of remote_tx_win for L2CAP ERTM

remote_tx_win is intended to be set on receipt of an L2CAP
configuration request.  The value is used to determine the size of the
transmit window on the remote side of an ERTM connection, so L2CAP
can stop sending frames when that remote window is full.

An incorrect remote_tx_win value will cause the stack to not fully
utilize the tx window (performance impact), or to overfill the remote
tx window (causing dropped frames or a disconnect).

This patch removes an extra setting of remote_tx_win when a
configuration response is received.  The transmit window has a
different meaning in a response - it is an informational value
less than or equal to the local tx_win.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
14 years agoBluetooth: Change default L2CAP ERTM retransmit timeout
Mat Martineau [Thu, 5 Aug 2010 22:54:20 +0000 (15:54 -0700)]
Bluetooth: Change default L2CAP ERTM retransmit timeout

The L2CAP specification requires that the ERTM retransmit timeout be at
least 2 seconds for BR/EDR connections.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
14 years agoBluetooth: Fix endianness issue with L2CAP MPS configuration
Mat Martineau [Thu, 5 Aug 2010 22:54:22 +0000 (15:54 -0700)]
Bluetooth: Fix endianness issue with L2CAP MPS configuration

Incoming configuration values must be converted to native CPU order
before use.  This fixes a bug where a little-endian MPS value is
compared to a native CPU value.  On big-endian processors, this
can cause ERTM and streaming mode segmentation to produce PDUs
that are larger than the remote stack is expecting, or that would
produce fragmented skbs that the current FCS code cannot handle.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
14 years agonet: Use NET_XMIT_SUCCESS where possible.
Ben Greear [Tue, 10 Aug 2010 08:45:40 +0000 (01:45 -0700)]
net: Use NET_XMIT_SUCCESS where possible.

This is based on work originally done by Patric McHardy.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoisdn: mISDN: call pci_disable_device() if pci_probe() failed
Kulikov Vasiliy [Mon, 9 Aug 2010 09:50:53 +0000 (09:50 +0000)]
isdn: mISDN: call pci_disable_device() if pci_probe() failed

Driver should call pci_disable_device() if it returns from pci_probe()
with error.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoisdn: avm: call pci_disable_device() if pci_probe() failed
Kulikov Vasiliy [Mon, 9 Aug 2010 09:50:47 +0000 (09:50 +0000)]
isdn: avm: call pci_disable_device() if pci_probe() failed

Driver should call pci_disable_device() if it returns from pci_probe()
with error.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoisdn: avm: call pci_disable_device() if pci_probe() failed
Kulikov Vasiliy [Mon, 9 Aug 2010 09:50:37 +0000 (09:50 +0000)]
isdn: avm: call pci_disable_device() if pci_probe() failed

Driver should call pci_disable_device() if it returns from pci_probe()
with error.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agousbnet: rx_submit() should return an error code.
David S. Miller [Tue, 10 Aug 2010 09:50:55 +0000 (02:50 -0700)]
usbnet: rx_submit() should return an error code.

This patch makes rx_submit() return an error code, and makes some call sites
that care check the return value. This is important because it lets us properly
handle cases where the device isn't ready to handle URB submissions (e.g., when
it is autosuspended under some drivers); previously, we would attempt and fail
to submit URBs and reschedule ourselves to try and fail again. This patch is
against Linus's 2.6 repo commit 45d7f32c7a43cbb9592886d38190e379e2eb2226.

Signed-Off-By: Elizabeth Jones <ellyjones@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agopkt_sched: Add some basic qdisc class ops verification. Was: [PATCH] sfq: add dummy...
Jarek Poplawski [Mon, 9 Aug 2010 12:18:48 +0000 (12:18 +0000)]
pkt_sched: Add some basic qdisc class ops verification. Was: [PATCH] sfq: add dummy bind/unbind handles

Verify in register_qdisc() some basic qdisc class handlers are present.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agopkt_sched: sch_sfq: Add dummy unbind_tcf and put handles. Was: [PATCH] sfq: add dummy...
Jarek Poplawski [Mon, 9 Aug 2010 12:18:17 +0000 (12:18 +0000)]
pkt_sched: sch_sfq: Add dummy unbind_tcf and put handles. Was: [PATCH] sfq: add dummy bind/unbind handles

Add dummy .unbind_tcf and .put qdisc class ops for easier verification.
(All other schedulers have it like this.)

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoqlcnic: using too much stack
Dan Carpenter [Mon, 9 Aug 2010 21:49:36 +0000 (21:49 +0000)]
qlcnic: using too much stack

qlcnic_pci_info structs are 128 bytes so an array of 8 uses 1024 bytes.
That's a lot if you run with 4K stacks.  I allocated them with kcalloc()
instead.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoqlcnic: clean up qlcnic_init_pci_info()
Dan Carpenter [Mon, 9 Aug 2010 21:47:56 +0000 (21:47 +0000)]
qlcnic: clean up qlcnic_init_pci_info()

In the original code we allocated memory conditionally and freed it in
the error handling unconditionally.  It turns out that this function is
only called during initialization and "adapter->npars" and
"adapter->eswitch" are always NULL at the start of the function.  I
removed those checks.

Also since I was cleaning things, I changed the error handling for
qlcnic_get_pci_info() and pulled everything in an indent level.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agophy.c: fix kernel-doc warnings
Randy Dunlap [Mon, 9 Aug 2010 13:41:59 +0000 (13:41 +0000)]
phy.c: fix kernel-doc warnings

Fix phy.c kernel-doc notation:

Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr'
Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agonet/sock.h: add missing kernel-doc notation
Randy Dunlap [Mon, 9 Aug 2010 13:41:07 +0000 (13:41 +0000)]
net/sock.h: add missing kernel-doc notation

Add missing kernel-doc notation to struct sock:

Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_pid'
Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_cred'
Warning(include/net/sock.h:324): No description found for parameter 'sk_classid'
Warning(include/net/sock.h:324): Excess struct/union/enum/typedef member 'sk_peercred' description in 'sock'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoetherdevice.h: fix kernel-doc typo
Randy Dunlap [Mon, 9 Aug 2010 13:40:03 +0000 (13:40 +0000)]
etherdevice.h: fix kernel-doc typo

Fix etherdevice.h parameter name typo in kernel-doc:

Warning(include/linux/etherdevice.h:138): No description found for parameter 'hwaddr'
Warning(include/linux/etherdevice.h:138): Excess function parameter 'addr' description in 'dev_hw_addr_random'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agofarsync: Fix compile warnings.
David S. Miller [Tue, 10 Aug 2010 07:06:58 +0000 (00:06 -0700)]
farsync: Fix compile warnings.

drivers/net/wan/farsync.c: In function 'fst_intr_rx':
drivers/net/wan/farsync.c:1312: warning: cast to pointer from integer of different size
drivers/net/wan/farsync.c: In function 'do_bottom_half_tx':
drivers/net/wan/farsync.c:1407: warning: cast to pointer from integer of different size

The "skb" and "mem" arguments being passed here are DMA addresses
being programmed into the hardware registers, so pass them as the type
that they actually are.  And use the correct printf formatting in
debug logging statements for these things to match the type change.

Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoiwlagn: fix rts cts protection
Johannes Berg [Mon, 9 Aug 2010 17:57:02 +0000 (10:57 -0700)]
iwlagn: fix rts cts protection

Currently the driver will try to protect all frames,
which leads to a lot of odd things like sending an
RTS with a zeroed RA before multicast frames, which
is clearly bogus.

In order to fix all of this, we need to take a step
back and see what we need to achieve:
 * we need RTS/CTS protection if requested by
   the AP for the BSS, mac80211 tells us this
 * in that case, CTS-to-self should only be
   enabled when mac80211 tells us
 * additionally, as a hardware workaround, on
   some devices we have to protect aggregated
   frames with RTS

To achieve the first two items, set up the RXON
accordingly and set the protection required flag
in the transmit command when mac80211 requests
protection for the frame.

To achieve the last item, set the rate-control
RTS-requested flag for all stations that we have
aggregation sessions with, and set the protection
required flag when sending aggregated frames (on
those devices where this is required).

Since otherwise bugs can occur, do not allow the
user to override the RTS-for-aggregation setting
from sysfs any more.

Finally, also clean up the way all these flags get
set in the driver and move everything into the
device-specific functions.

Cc: stable@kernel.org [2.6.35]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agocfg80211: fix locking in action frame TX
Johannes Berg [Mon, 9 Aug 2010 13:52:03 +0000 (15:52 +0200)]
cfg80211: fix locking in action frame TX

Accesses to "wdev->current_bss" must be
locked with the wdev lock, which action
frame transmission is missing.

Cc: stable@kernel.org [2.6.33+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agolibertas: fix build break by including linux/sched.h
John W. Linville [Mon, 9 Aug 2010 19:14:21 +0000 (15:14 -0400)]
libertas: fix build break by including linux/sched.h

  CC [M]  drivers/net/wireless/libertas/cfg.o
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_scan_worker’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: ‘TASK_NORMAL’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: (Each undeclared identifier is reported only once
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: for each function it appears in.)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_cfg_connect’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘signal_pending’
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘schedule_timeout’

Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoRevert "p54pci: Add PCI ID for SMC2802W"
John W. Linville [Mon, 9 Aug 2010 16:04:56 +0000 (12:04 -0400)]
Revert "p54pci: Add PCI ID for SMC2802W"

This reverts commit 5f7aebd845a9d2ed42f36b7333579ec3534b4713.

Apparently, that PCI ID data was incorrectly taken from the subsystem
information.  The actual ID matches another already known ID.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoigbvf.txt: Add igbvf Documentation
Jeff Kirsher [Sun, 8 Aug 2010 15:54:31 +0000 (15:54 +0000)]
igbvf.txt: Add igbvf Documentation

Adds documentation for the igbvf (igb virtual function driver).

  v2:
   - Removed trailing white space
   - Removed Ethtool version info

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoigb.txt: Add igb documentation
Jeff Kirsher [Sun, 8 Aug 2010 15:54:11 +0000 (15:54 +0000)]
igb.txt: Add igb documentation

Add documentation for the igb networking driver.

  v2:
   - Removed trailing white space
   - Removed Ethtool version info
   - Removed LRO kernel version info

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoe100/e1000*/igb*/ixgb*: Add missing read memory barrier
Jeff Kirsher [Sun, 8 Aug 2010 16:02:31 +0000 (16:02 +0000)]
e100/e1000*/igb*/ixgb*: Add missing read memory barrier

Based on patches from Sonny Rao and Milton Miller...

Combined the patches to fix up clean_tx_irq and clean_rx_irq.

The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.

In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.

The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.

This bug was found during stress testing and adding this barrier has
been shown to fix it.  The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().

This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.

Previously Submitted to e1000-devel only for ixgbe

http://marc.info/?l=e1000-devel&m=126593062701537&w=3

We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.

CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG
John Fastabend [Sun, 8 Aug 2010 15:46:15 +0000 (15:46 +0000)]
ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG

Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause
a build error.  This resolves the build error by wrapping
the fcoe.up in CONFIG_IXGBE_DCB ifdefs.

Also frames were being priority VLAN tagged even without DCB
enabled.  This fixes this so that 8021Q priority tags are
only added with DCB actually enabled.

Reported-by: divya <dipraksh@linux.vnet.ibm.com>
Reported-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agonetxen: protect tx timeout recovery by rtnl lock
Amit Kumar Salecha [Sun, 8 Aug 2010 06:05:23 +0000 (23:05 -0700)]
netxen: protect tx timeout recovery by rtnl lock

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoisdn: gigaset: use after free
Dan Carpenter [Thu, 5 Aug 2010 22:21:26 +0000 (22:21 +0000)]
isdn: gigaset: use after free

I moved the kfree(cb) below the dereferences.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoisdn: gigaset: add missing unlock
Dan Carpenter [Thu, 5 Aug 2010 22:23:23 +0000 (22:23 +0000)]
isdn: gigaset: add missing unlock

We should unlock here.  This is the only place where we return from the
function with the lock held.  The caller isn't expecting it.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agosolos-pci: Fix race condition in tasklet RX handling
David Woodhouse [Sun, 8 Aug 2010 06:02:59 +0000 (23:02 -0700)]
solos-pci: Fix race condition in tasklet RX handling

We were seeing faults in the solos-pci receive tasklet when packets
arrived for a VCC which was currently being closed:

[18842.727906] EIP: [<e082f490>] br2684_push+0x19/0x234 [br2684] SS:ESP 0068:dfb89d14

[18845.090712] [<c13ecff3>] ? do_page_fault+0x0/0x2e1
[18845.120042] [<e082f490>] ? br2684_push+0x19/0x234 [br2684]
[18845.153530] [<e084fa13>] solos_bh+0x28b/0x7c8 [solos_pci]
[18845.186488] [<e084f711>] ? solos_irq+0x2d/0x51 [solos_pci]
[18845.219960] [<c100387b>] ? handle_irq+0x3b/0x48
[18845.247732] [<c10265cb>] ? irq_exit+0x34/0x57
[18845.274437] [<c1025720>] tasklet_action+0x42/0x69
[18845.303247] [<c102643f>] __do_softirq+0x8e/0x129
[18845.331540] [<c10264ff>] do_softirq+0x25/0x2a
[18845.358274] [<c102664c>] _local_bh_enable_ip+0x5e/0x6a
[18845.389677] [<c102666d>] local_bh_enable+0xb/0xe
[18845.417944] [<e08490a8>] ppp_unregister_channel+0x32/0xbb [ppp_generic]
[18845.458193] [<e08731ad>] pppox_unbind_sock+0x18/0x1f [pppox]

This patch uses an RCU-inspired approach to fix it. In the RX tasklet's
find_vcc() function we first refuse to use a VCC which already has the
ATM_VF_READY bit cleared. And in the VCC close function, we synchronise
with the tasklet to ensure that it can't still be using the VCC before
we continue and allow the VCC to be destroyed.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Nathan Williams <nathan@traverse.com.au>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agopkt_sched: Fix sch_sfq vs tcf_bind_filter oops
Jarek Poplawski [Fri, 6 Aug 2010 00:22:35 +0000 (00:22 +0000)]
pkt_sched: Fix sch_sfq vs tcf_bind_filter oops

Since there was added ->tcf_chain() method without ->bind_tcf() to
sch_sfq class options, there is oops when a filter is added with
the classid parameter.

Fixes commit 7d2681a6ff4f9ab5e48d02550b4c6338f1638998
netdev thread: null pointer at cls_api.c

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Reported-by: Franchoze Eric <franchoze@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agonet: disable preemption before call smp_processor_id()
Changli Gao [Sun, 8 Aug 2010 03:35:43 +0000 (20:35 -0700)]
net: disable preemption before call smp_processor_id()

Although netif_rx() isn't expected to be called in process context with
preemption enabled, it'd better handle this case. And this is why get_cpu()
is used in the non-RPS #ifdef branch. If tree RCU is selected,
rcu_read_lock() won't disable preemption, so preempt_disable() should be
called explictly.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agotcp: no md5sig option size check bug
Dmitry Popov [Sun, 8 Aug 2010 03:24:28 +0000 (20:24 -0700)]
tcp: no md5sig option size check bug

tcp_parse_md5sig_option doesn't check md5sig option (TCPOPT_MD5SIG)
length, but tcp_v[46]_inbound_md5_hash assume that it's at least 16
bytes long.

Signed-off-by: Dmitry Popov <dp@highloadlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Fri, 6 Aug 2010 20:30:43 +0000 (13:30 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

14 years agoiwlwifi: fix locking assertions
Johannes Berg [Fri, 6 Aug 2010 14:17:53 +0000 (16:17 +0200)]
iwlwifi: fix locking assertions

spin_is_locked() can return zero on some (UP?)
configurations because locks don't exist, and
that causes an endless amount of warnings. Use
lockdep_assert_held() instead, which has two
advantages:
 1) it verifies the current task is holding
    the lock or mutex
 2) it compiles away completely when lockdep
    is not enabled

Cc: stable@kernel.org [2.6.34+, maybe only parts of patch]
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoiwlwifi: fix TX tracer
Johannes Berg [Fri, 6 Aug 2010 14:00:48 +0000 (16:00 +0200)]
iwlwifi: fix TX tracer

The TX tracing code copies with the wrong length,
which will typically copy too little data. Fix
this by using the correct length variable.

Cc: stable@kernel.org [2.6.32+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoisdn: fix information leak
Dan Carpenter [Wed, 4 Aug 2010 23:38:06 +0000 (23:38 +0000)]
isdn: fix information leak

The main motivation of this patch changing strcpy() to strlcpy().
We strcpy() to copy a 48 byte buffers into a 49 byte buffers.  So at
best the last byte has leaked information, or maybe there is an
overflow?  Anyway, this patch closes the information leaks by zeroing
the memory and the calls to strlcpy() prevent overflows.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agonet: Fix napi_gro_frags vs netpoll path
Jarek Poplawski [Thu, 5 Aug 2010 01:19:11 +0000 (01:19 +0000)]
net: Fix napi_gro_frags vs netpoll path

The netpoll_rx_on() check in __napi_gro_receive() skips part of the
"common" GRO_NORMAL path, especially "pull:" in dev_gro_receive(),
where at least eth header should be copied for entirely paged skbs.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agousbnet: remove noisy and hardly useful printk
Christian Samsel [Wed, 4 Aug 2010 22:14:36 +0000 (22:14 +0000)]
usbnet: remove noisy and hardly useful printk

With turned on hspa modem (Dell 5530 internal card) and activated usb auto
suspend, my system gets up 100 "usbnet_resume has delayed data" per
minute. I didnt noticed any pathological behaviour, so just drop
this message. if any objections, please at least change it to _DEBUG.

Signed-off-by: Christian Samsel <christian.samsel@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agortl8180: avoid potential NULL deref in rtl8180_beacon_work
John W. Linville [Thu, 5 Aug 2010 17:46:27 +0000 (13:46 -0400)]
rtl8180: avoid potential NULL deref in rtl8180_beacon_work

ieee80211_beacon_get can return NULL...

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
14 years agoath9k: Remove myself from the MAINTAINERS list
Sujith [Fri, 30 Jul 2010 06:31:17 +0000 (12:01 +0530)]
ath9k: Remove myself from the MAINTAINERS list

So long.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agolibertas: scan before assocation if no BSSID was given
Dan Williams [Wed, 4 Aug 2010 05:43:47 +0000 (00:43 -0500)]
libertas: scan before assocation if no BSSID was given

Fix this leftover TODO from the cfg80211 conversion by doing a scan
if cfg80211 didn't pass in the BSSID for us.  Since the scan code
uses so much of the cfg80211_scan_request structure to build up the
firmware command, we just fake one when the scan request is triggered
internally.  But we need to make sure that internal 'fake' cfg82011
scan request does not get back to cfg82011 via cfg80211_scan_done().

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agolibertas: fix association with some APs by using extended rates
Dan Williams [Fri, 30 Jul 2010 06:16:01 +0000 (23:16 -0700)]
libertas: fix association with some APs by using extended rates

Some APs get pissy if you don't send the firmware the extended rates
in the association request's rates TLV.  Found this on a Linksys
WRT54G v2; it denies association with status code 18 unless you
add the extended rates too.  The old driver did this, but it got
lost in the cfg80211 conversion.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agolibertas: get the right # of scanned BSSes
Dan Williams [Fri, 30 Jul 2010 06:11:30 +0000 (23:11 -0700)]
libertas: get the right # of scanned BSSes

Let's actually check the right field in the command response; and
if there aren't any reported BSSes, exit early with success.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluet...
John W. Linville [Thu, 5 Aug 2010 19:54:28 +0000 (15:54 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/holtmann/bluetooth-next-2.6

14 years agovirtio_net: implements ethtool_ops.get_drvinfo
Rusty Russell [Wed, 4 Aug 2010 17:32:05 +0000 (17:32 +0000)]
virtio_net: implements ethtool_ops.get_drvinfo

I often use "ethtool -i" command to check what driver controls the
ehternet device.  But because current virtio_net driver doesn't
support "ethtool -i", it becomes the following:

        # ethtool -i eth3
        Cannot get driver information: Operation not supported

This patch simply adds the "ethtool -i" support. The following is the
result when using the virtio_net driver with my patch applied to.

        # ethtool -i eth3
        driver: virtio_net
        version: N/A
        firmware-version: N/A
        bus-info: virtio0

Personally, "-i" is one of the most frequently-used option, and most
network drivers support "ethtool -i", so I think virtio_net also
should do.

Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE)
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoppp: make channel_ops const
stephen hemminger [Wed, 4 Aug 2010 07:34:36 +0000 (07:34 +0000)]
ppp: make channel_ops const

The PPP channel ops structure should be const.
Cleanup the declarations to use standard C99 format.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoRxRPC: Fix a potential deadlock between the call resend_timer and state_lock
David Howells [Wed, 4 Aug 2010 02:34:17 +0000 (02:34 +0000)]
RxRPC: Fix a potential deadlock between the call resend_timer and state_lock

RxRPC can potentially deadlock as rxrpc_resend_time_expired() wants to get
call->state_lock so that it can alter the state of an RxRPC call.  However, its
caller (call_timer_fn()) has an apparent lock on the timer struct.

The problem is that rxrpc_resend_time_expired() isn't permitted to lock
call->state_lock as this could cause a deadlock against rxrpc_send_abort() as
that takes state_lock and then attempts to delete the resend timer by calling
del_timer_sync().

The deadlock can occur because del_timer_sync() will sit there forever waiting
for rxrpc_resend_time_expired() to return, but the latter may then wait for
call->state_lock, which rxrpc_send_abort() holds around del_timer_sync()...

This leads to a warning appearing in the kernel log that looks something like
the attached.

It should be sufficient to simply dispense with the locks.  It doesn't matter
if we set the resend timer expired event bit and queue the event processor
whilst we're changing state to one where the resend timer is irrelevant as the
event can just be ignored by the processor thereafter.

=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.35-rc3-cachefs+ #115
-------------------------------------------------------
swapper/0 is trying to acquire lock:
 (&call->state_lock){++--..}, at: [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]

but task is already holding lock:
 (&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&call->resend_timer){+.-...}:
       [<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
       [<ffffffff81056184>] lock_acquire+0x57/0x6d
       [<ffffffff8103bb9c>] del_timer_sync+0x3c/0x86
       [<ffffffffa002bb7a>] rxrpc_send_abort+0x50/0x97 [af_rxrpc]
       [<ffffffffa002bdd9>] rxrpc_kernel_abort_call+0xa1/0xdd [af_rxrpc]
       [<ffffffffa0061588>] afs_deliver_to_call+0x129/0x368 [kafs]
       [<ffffffffa006181b>] afs_process_async_call+0x54/0xff [kafs]
       [<ffffffff8104261d>] worker_thread+0x1ef/0x2e2
       [<ffffffff81045f47>] kthread+0x7a/0x82
       [<ffffffff81002cd4>] kernel_thread_helper+0x4/0x10

-> #0 (&call->state_lock){++--..}:
       [<ffffffff81055237>] validate_chain+0x727/0xd23
       [<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
       [<ffffffff81056184>] lock_acquire+0x57/0x6d
       [<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
       [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
       [<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
       [<ffffffff81036828>] __do_softirq+0xa2/0x13e
       [<ffffffff81002dcc>] call_softirq+0x1c/0x28
       [<ffffffff810049f0>] do_softirq+0x38/0x80
       [<ffffffff810361a2>] irq_exit+0x45/0x47
       [<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
       [<ffffffff81002893>] apic_timer_interrupt+0x13/0x20
       [<ffffffff810011ac>] cpu_idle+0x4d/0x83
       [<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1

other info that might help us debug this:

1 lock held by swapper/0:
 #0:  (&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5

stack backtrace:
Pid: 0, comm: swapper Not tainted 2.6.35-rc3-cachefs+ #115
Call Trace:
 <IRQ>  [<ffffffff81054414>] print_circular_bug+0xae/0xbd
 [<ffffffff81055237>] validate_chain+0x727/0xd23
 [<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
 [<ffffffff810539a7>] ? mark_lock+0x42f/0x51f
 [<ffffffff81056184>] lock_acquire+0x57/0x6d
 [<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
 [<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
 [<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
 [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
 [<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
 [<ffffffff8103b675>] ? run_timer_softirq+0x182/0x2a5
 [<ffffffffa002007e>] ? rxrpc_resend_time_expired+0x0/0x96 [af_rxrpc]
 [<ffffffff810367ef>] ? __do_softirq+0x69/0x13e
 [<ffffffff81036828>] __do_softirq+0xa2/0x13e
 [<ffffffff81002dcc>] call_softirq+0x1c/0x28
 [<ffffffff810049f0>] do_softirq+0x38/0x80
 [<ffffffff810361a2>] irq_exit+0x45/0x47
 [<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
 [<ffffffff81002893>] apic_timer_interrupt+0x13/0x20
 <EOI>  [<ffffffff81049de1>] ? __atomic_notifier_call_chain+0x0/0x86
 [<ffffffff8100955b>] ? mwait_idle+0x6e/0x78
 [<ffffffff81009552>] ? mwait_idle+0x65/0x78
 [<ffffffff810011ac>] cpu_idle+0x4d/0x83
 [<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agosch_sfq: add sanity check for the packet length
Changli Gao [Wed, 4 Aug 2010 04:58:59 +0000 (04:58 +0000)]
sch_sfq: add sanity check for the packet length

The packet length should be checked before the packet data is dereferenced.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agocls_rsvp: add sanity check for the packet length
Changli Gao [Wed, 4 Aug 2010 04:55:40 +0000 (04:55 +0000)]
cls_rsvp: add sanity check for the packet length

The packet length should be checked before the packet data is dereferenced.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agocls_flow: add sanity check for the packet length
Changli Gao [Wed, 4 Aug 2010 04:48:12 +0000 (04:48 +0000)]
cls_flow: add sanity check for the packet length

The packet length should be checked before the packet data is dereferenced.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agosk_buff: introduce pskb_network_may_pull()
Changli Gao [Wed, 4 Aug 2010 04:43:44 +0000 (04:43 +0000)]
sk_buff: introduce pskb_network_may_pull()

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoact_nat: fix on the TX path
Changli Gao [Tue, 3 Aug 2010 17:39:18 +0000 (17:39 +0000)]
act_nat: fix on the TX path

On the TX path, skb->data points to the ethernet header, not the network
header. So when validating the packet length for accessing we should
take the ethernet header into account.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agodrivers/net/enic: Use %pUB to format a UUID
Joe Perches [Tue, 3 Aug 2010 09:32:24 +0000 (09:32 +0000)]
drivers/net/enic: Use %pUB to format a UUID

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agodavinci_emac: Fix use after free in davinci_emac_remove
Stefan Weil [Tue, 3 Aug 2010 08:53:45 +0000 (08:53 +0000)]
davinci_emac: Fix use after free in davinci_emac_remove

free_netdev finally calls kfree which makes the contents
of ndev and priv (private data contained in ndev) invalid.

So iounmap should be called before free_netdev.

Cc: David S. Miller <davem@davemloft.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sriramakrishnan <srk@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agovia-velocity: do not use PCI resources before pci_enable_device()
Kulikov Vasiliy [Tue, 3 Aug 2010 05:43:18 +0000 (05:43 +0000)]
via-velocity: do not use PCI resources before pci_enable_device()

IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.

The semantic match that finds this problem is as follows:

// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@

(
* x->irq
|
* x->resource
|
* request(x, ...)
)
 ...
*pci_enable_device(x)
// </smpl>

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agocxgb4vf: do not use PCI resources before pci_enable_device()
Kulikov Vasiliy [Tue, 3 Aug 2010 05:43:15 +0000 (05:43 +0000)]
cxgb4vf: do not use PCI resources before pci_enable_device()

IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.

The semantic match that finds this problem is as follows:

// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@

(
* x->irq
|
* x->resource
|
* request(x, ...)
)
 ...
*pci_enable_device(x)
// </smpl>

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agocxgb3: do not use PCI resources before pci_enable_device()
Kulikov Vasiliy [Tue, 3 Aug 2010 05:43:11 +0000 (05:43 +0000)]
cxgb3: do not use PCI resources before pci_enable_device()

IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.

The semantic match that finds this problem is as follows:

// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@

(
* x->irq
|
* x->resource
|
* request(x, ...)
)
 ...
*pci_enable_device(x)
// </smpl>

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
14 years agoMerge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Linus Torvalds [Wed, 4 Aug 2010 22:31:02 +0000 (15:31 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/jikos/trivial

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (48 commits)
  Documentation: update broken web addresses.
  fix comment typo "choosed" -> "chosen"
  hostap:hostap_hw.c Fix typo in comment
  Fix spelling contorller -> controller in comments
  Kconfig.debug: FAIL_IO_TIMEOUT: typo Faul -> Fault
  fs/Kconfig: Fix typo Userpace -> Userspace
  Removing dead MACH_U300_BS26
  drivers/infiniband: Remove unnecessary casts of private_data
  fs/ocfs2: Remove unnecessary casts of private_data
  libfc: use ARRAY_SIZE
  scsi: bfa: use ARRAY_SIZE
  drm: i915: use ARRAY_SIZE
  drm: drm_edid: use ARRAY_SIZE
  synclink: use ARRAY_SIZE
  block: cciss: use ARRAY_SIZE
  comment typo fixes: charater => character
  fix comment typos concerning "challenge"
  arm: plat-spear: fix typo in kerneldoc
  reiserfs: typo comment fix
  update email address
  ...

14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Linus Torvalds [Wed, 4 Aug 2010 22:23:49 +0000 (15:23 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
  Revert "HID: add support for the Wacom Intuos 4 wireless"
  HID: fix up Kconfig entry for ACRUX driver
  HID: add ACRUX game controller force feedback support
  HID: Force input registration for "VEC footpedal"
  HID: add HID_QUIRK_HIDINPUT_FORCE
  HID: hid-input.c: indentation fixes
  HID: hiddev: use usb_find_interface, get rid of BKL
  HID: ignore digitizer usage Undefined (0x00)
  HID: Add support for Conceptronic CLLRCMCE
  HID: hid-ids.h: Whitespace fixup, align using TABs
  HID: picolcd: implement refcounting of framebuffer
  HID: picolcd: do not reallocate memory on depth change
  HID: picolcd: Add minimal palette required by fbcon on 8bpp
  HID: magicmouse: Correct parsing of large X and Y motions.
  HID: magicmouse: report last touch up
  HID: picolcd: fix deferred_io init/cleanup to fb ordering
  HID: hid-ids.h: keep vendor ids in alphabetical order
  HID: add proper support for Elecom BM084 bluetooth mouse
  HID: magicmouse: enable horizontal scrolling
  HID: magicmouse: add param for scroll speed
  ...

14 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Linus Torvalds [Wed, 4 Aug 2010 22:23:14 +0000 (15:23 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (39 commits)
  random: Reorder struct entropy_store to remove padding on 64bits
  padata: update API documentation
  padata: Remove padata_get_cpumask
  crypto: pcrypt - Update pcrypt cpumask according to the padata cpumask notifier
  crypto: pcrypt - Rename pcrypt_instance
  padata: Pass the padata cpumasks to the cpumask_change_notifier chain
  padata: Rearrange set_cpumask functions
  padata: Rename padata_alloc functions
  crypto: pcrypt - Dont calulate a callback cpu on empty callback cpumask
  padata: Check for valid cpumasks
  padata: Allocate cpumask dependend recources in any case
  padata: Fix cpu index counting
  crypto: geode_aes - Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
  pcrypt: Added sysfs interface to pcrypt
  padata: Added sysfs primitives to padata subsystem
  padata: Make two separate cpumasks
  padata: update documentation
  padata: simplify serialization mechanism
  padata: make padata_do_parallel to return zero on success
  padata: Handle empty padata cpumasks
  ...

14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Linus Torvalds [Wed, 4 Aug 2010 22:17:52 +0000 (15:17 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tj/percpu

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: allow limited allocation before slab is online
  percpu: make @dyn_size always mean min dyn_size in first chunk init functions

14 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Linus Torvalds [Wed, 4 Aug 2010 22:15:15 +0000 (15:15 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-misc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (276 commits)
  [SCSI] zfcp: Trigger logging in the FCP channel on qdio error conditions
  [SCSI] zfcp: Introduce experimental support for DIF/DIX
  [SCSI] zfcp: Enable data division support for FCP devices
  [SCSI] zfcp: Prevent access on uninitialized memory.
  [SCSI] zfcp: Post events through FC transport class
  [SCSI] zfcp: Cleanup QDIO attachment and improve processing.
  [SCSI] zfcp: Cleanup function parameters for sbal value.
  [SCSI] zfcp: Use correct width for timer_interval field
  [SCSI] zfcp: Remove SCSI device when removing unit
  [SCSI] zfcp: Use memdup_user and kstrdup
  [SCSI] zfcp: Fix retry after failed "open port" erp action
  [SCSI] zfcp: Fail erp after timeout
  [SCSI] zfcp: Use forced_reopen in terminate_rport_io callback
  [SCSI] zfcp: Register SCSI devices after successful fc_remote_port_add
  [SCSI] zfcp: Do not try "forced close" when port is already closed
  [SCSI] zfcp: Do not unblock rport from REOPEN_PORT_FORCED
  [SCSI] sd: add support for runtime PM
  [SCSI] implement runtime Power Management
  [SCSI] convert to the new PM framework
  [SCSI] Unify SAM_ and SAM_STAT_ macros
  ...

14 years agoiwlagn: Improve aggregation failure error messages
Andy Lutomirski [Sun, 25 Jul 2010 17:14:29 +0000 (13:14 -0400)]
iwlagn: Improve aggregation failure error messages

82ca9341763107615a15da6e59b9535d49eb91c3 added scary looking
but harmless error messages.  Make them clearer and make the
actual failure message show up with the same severity as the
harmless one.

Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agort2x00: do not use PCI resources before pci_enable_device()
Kulikov Vasiliy [Tue, 3 Aug 2010 15:43:22 +0000 (19:43 +0400)]
rt2x00: do not use PCI resources before pci_enable_device()

IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.

The semantic match that finds this problem is as follows:

// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@

(
* x->irq
|
* x->resource
|
* request(x, ...)
)
 ...
*pci_enable_device(x)
// </smpl>

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agomac80211: Fix compilation warning when CONFIG_INET is not set
Juuso Oikarinen [Tue, 3 Aug 2010 05:22:25 +0000 (08:22 +0300)]
mac80211: Fix compilation warning when CONFIG_INET is not set

The warning is:
  net/mac80211/main.c:688: warning: label ‘fail_ifa’ defined but not used

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agowireless: ipw2100: check result of kzalloc()
Christoph Fritz [Tue, 3 Aug 2010 10:54:20 +0000 (12:54 +0200)]
wireless: ipw2100: check result of kzalloc()

If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is
called by register_netdev.

CC: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k: fix erased ieee80211_rx_status.mactime
Jan Friedrich [Mon, 2 Aug 2010 21:55:50 +0000 (23:55 +0200)]
ath9k: fix erased ieee80211_rx_status.mactime

ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again -
mactime is always 0. This causes problems in IBSS mode.

ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed.
Without this patch the merge is triggered by each beacon received.

This can be recognized by the "beacon TSF higher than local TSF - IBSS
merge with BSSID" log message accompanying each beacon.

This problem was not completely fixed in commit
a6d2055b02dde1067075795274672720baadd3ca and is not a stable kernel fix.
It is solely intended for wireless-testing.

Signed-off-by: Jan Friedrich <jft@dev2day.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agop54pci: Add PCI ID for SMC2802W
Larry Finger [Sun, 1 Aug 2010 20:40:04 +0000 (15:40 -0500)]
p54pci: Add PCI ID for SMC2802W

The SMC2802W appears to work with p54pci.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: David Cozatt <olbrannon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k: fix an issue in ath_atx_tid paused flag management
Lorenzo Bianconi [Sun, 1 Aug 2010 13:47:32 +0000 (15:47 +0200)]
ath9k: fix an issue in ath_atx_tid paused flag management

I noticed a possible issue in the paused flag management of the
ath_atx_tid data structure. In particular, in a noisy environment and
under heavy load, I observed that the AGGR session establishment could
fail several times consecutively causing values of the paused flag
greater than one for this TID (ath_tx_pause_tid is called more than
once from ath_tx_aggr_start).

Considering that the session for this TID can not be established also
after the mac80211 stack calls the ieee80211_agg_tx_operational() since
the ath_tx_aggr_resume() lowers the paused flag only by one.

This patch also replaces some BUG_ON calls with WARN_ON, as even if
these unlikely conditions happen, it's not fatal enough to justify a
BUG_ON.

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k_hw: Fix regulatory CTL index usage for AR9003
Luis R. Rodriguez [Sun, 1 Aug 2010 06:25:16 +0000 (02:25 -0400)]
ath9k_hw: Fix regulatory CTL index usage for AR9003

AR9003 was not relying on the CTL indexes from the EEPROM for capping the
max output power. The CTL indexes from the EEPROM provide calibrated
limits for output power for each tested and supported frequency. Without
this the device operates at a power level which only conforms to the
transmit spectrum mask as specified by IEEE Annex I.2.3.

The regulatory limit by CRDA is always used but does not provide
calibrated values for optimal performance, specially on band edges.
Using the calibrated data from the EEPROM ensures the device
operates at optimal output power while still ensuring proper
regulatory compliance. The device uses the minimum of these tree
values, the value from CRDA, the calibrated value from CTL indexex,
and the value to conform to the IEEE transmit spectrum mask.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agonet: wl12xx: do not use kfree'd memory
Kulikov Vasiliy [Sat, 31 Jul 2010 16:33:59 +0000 (20:33 +0400)]
net: wl12xx: do not use kfree'd memory

wl1271_dump() uses cmd after kfree(cmd). Move kfree() just after
wl1271_dump().

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoiwlagn: fix typo in ucode_bt_stats_read debugfs
Wey-Yi Guy [Sat, 31 Jul 2010 15:34:12 +0000 (08:34 -0700)]
iwlagn: fix typo in ucode_bt_stats_read debugfs

small typo fix in ucode_bt_stats_read debugfs file

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoiwlwifi: BA scd_flow not match condition detected
Wey-Yi Guy [Sat, 31 Jul 2010 15:34:11 +0000 (08:34 -0700)]
iwlwifi: BA scd_flow not match condition detected

It is a uCode bug which cause the tx queue id not match scd_flow
in compressed block ack frame, and it need to be addressed in uCode.
Currently, driver will log the information when it happen.

Since it is possible happen very often and we do not want to fill the syslog,
so don't enable the logging by default.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoiwlwifi: fix compile warning
Johannes Berg [Sat, 31 Jul 2010 15:34:09 +0000 (08:34 -0700)]
iwlwifi: fix compile warning

When iwlwifi is compiled w/o debug, we get
this warning:
iwl-agn.c: In function ‘iwlagn_load_firmware’:
iwl-agn.c:2014: warning: passing argument 3 of ‘iwl_print_hex_dump’ discards qualifiers from pointer target type
iwl-debug.h:73: note: expected ‘void *’ but argument is of type ‘const u8 *’

because the const qualifier is missing in the
inline stub. Fix this.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k_hw: fix a noise floor calibration related race condition
Felix Fietkau [Fri, 30 Jul 2010 22:12:01 +0000 (00:12 +0200)]
ath9k_hw: fix a noise floor calibration related race condition

On AR5008-AR9002, other forms of calibration must not be started while
the noise floor calibration is running, as this can create invalid
readings which were sometimes not even recoverable by any further
calibration attempts.

This patch also ensures that the result of noise floor measurements
are processed faster and also allows the result of the initial
calibration on reset to make it into the NF history buffer

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k_hw: clean up per-channel calibration data
Felix Fietkau [Fri, 30 Jul 2010 22:12:00 +0000 (00:12 +0200)]
ath9k_hw: clean up per-channel calibration data

The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.

This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.

For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.

For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k: prevent calibration during off-channel activity
Felix Fietkau [Fri, 30 Jul 2010 22:11:59 +0000 (00:11 +0200)]
ath9k: prevent calibration during off-channel activity

Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.

This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k_hw: fix analog shift register writes on AR9003
Felix Fietkau [Fri, 30 Jul 2010 19:02:12 +0000 (21:02 +0200)]
ath9k_hw: fix analog shift register writes on AR9003

Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k: fix a crash in the PA predistortion apply function
Felix Fietkau [Fri, 30 Jul 2010 19:02:11 +0000 (21:02 +0200)]
ath9k: fix a crash in the PA predistortion apply function

When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k_hw: fix periodic noise floor calibration on AR9003
Felix Fietkau [Fri, 30 Jul 2010 19:02:10 +0000 (21:02 +0200)]
ath9k_hw: fix periodic noise floor calibration on AR9003

The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.

Fix this with a call to ath9k_hw_getnf(), just like on AR9002.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoath9k_hw: clean up and fix initial noise floor calibration
Felix Fietkau [Fri, 30 Jul 2010 19:02:09 +0000 (21:02 +0200)]
ath9k_hw: clean up and fix initial noise floor calibration

On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agomac80211: fix scan locking wrt. hw scan
Johannes Berg [Fri, 30 Jul 2010 11:30:47 +0000 (13:30 +0200)]
mac80211: fix scan locking wrt. hw scan

Releasing the scan mutex while starting scans
can lead to unexpected things happening, so
we shouldn't do that. Fix that and hold the
mutex across the scan triggering.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoiwlwifi: fix possible recursive locking deadlock
Johannes Berg [Fri, 30 Jul 2010 11:30:46 +0000 (13:30 +0200)]
iwlwifi: fix possible recursive locking deadlock

commit f84b29ec0a1ab767679d3f2428877b65f94bc3ff
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Tue May 18 02:29:13 2010 -0700

    iwlwifi: queue user-initiated scan when doing internal scan

introduced a potential deadlock because it calls
ieee80211_scan_completed() with the priv->mutex
held, but mac80211 may call back into iwlwifi
which would lead to recursive locking. Move this
out from under the mutex.

Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
Linus Torvalds [Wed, 4 Aug 2010 18:47:58 +0000 (11:47 -0700)]
Merge git://git./linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
  phy/marvell: add 88ec048 support
  igb: Program MDICNFG register prior to PHY init
  e1000e: correct MAC-PHY interconnect register offset for 82579
  hso: Add new product ID
  can: Add driver for esd CAN-USB/2 device
  l2tp: fix export of header file for userspace
  can-raw: Fix skb_orphan_try handling
  Revert "net: remove zap_completion_queue"
  net: cleanup inclusion
  phy/marvell: add 88e1121 interface mode support
  u32: negative offset fix
  net: Fix a typo from "dev" to "ndev"
  igb: Use irq_synchronize per vector when using MSI-X
  ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
  e1000e: Fix irq_synchronize in MSI-X case
  e1000e: register pm_qos request on hardware activation
  ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
  net: Add getsockopt support for TCP thin-streams
  cxgb4: update driver version
  cxgb4: add new PCI IDs
  ...

Manually fix up conflicts in:
 - drivers/net/e1000e/netdev.c: due to pm_qos registration
   infrastructure changes
 - drivers/net/phy/marvell.c: conflict between adding 88ec048 support
   and cleaning up the IDs
 - drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
   conflict (registration change vs marking it static)

14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad...
Linus Torvalds [Wed, 4 Aug 2010 18:25:58 +0000 (11:25 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/konrad/ibft-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft-2.6:
  ibft: Use IBFT_SIGN instead of open-coding the search string.
  ibft: convert iscsi_ibft module to iscsi boot lib
  ibft: separate ibft parsing from sysfs interface
  ibft: For UEFI machines actually do scan ACPI for iBFT.
  ibft: Update iBFT handling for v1.03 of the spec.

14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Linus Torvalds [Wed, 4 Aug 2010 18:23:59 +0000 (11:23 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/bp/bp

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  amd64_edac: Minor formatting fix
  amd64_edac: Fix operator precendence error
  edac, mc: Improve scrub rate handling
  amd64_edac: Correct scrub rate setting
  amd64_edac: Fix DCT base address selector
  amd64_edac: Remove polling mechanism
  x86, mce: Notify about corrected events too
  amd64_edac: Remove unneeded defines
  edac: Remove EDAC_DEBUG_VERBOSE
  amd64_edac: Sanitize syndrome extraction

14 years agoCRED: Fix RCU warning due to previous patch fixing __task_cred()'s checks
David Howells [Wed, 4 Aug 2010 15:59:14 +0000 (16:59 +0100)]
CRED: Fix RCU warning due to previous patch fixing __task_cred()'s checks

Commit 8f92054e7ca1 ("CRED: Fix __task_cred()'s lockdep check and banner
comment") fixed the lockdep checks on __task_cred().  This has shown up
a place in the signalling code where a lock should be held - namely that
check_kill_permission() requires its callers to hold the RCU lock.

Fix group_send_sig_info() to get the RCU read lock around its call to
check_kill_permission().

Without this patch, the following warning can occur:

  ===================================================
  [ INFO: suspicious rcu_dereference_check() usage. ]
  ---------------------------------------------------
  kernel/signal.c:660 invoked rcu_dereference_check() without protection!
  ...

Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
14 years agoblock_dev: always serialize exclusive open attempts
Tejun Heo [Wed, 4 Aug 2010 15:59:39 +0000 (17:59 +0200)]
block_dev: always serialize exclusive open attempts

bd_prepare_to_claim() incorrectly allowed multiple attempts for
exclusive open to progress in parallel if the attempting holders are
identical.  This triggered BUG_ON() as reported in the following bug.

  https://bugzilla.kernel.org/show_bug.cgi?id=16393

__bd_abort_claiming() is used to finish claiming blocks and doesn't
work if multiple openers are inside a claiming block.  Allowing
multiple parallel open attempts to continue doesn't gain anything as
those are serialized down in the call chain anyway.  Fix it by always
allowing only single open attempt in a claiming block.

This problem can easily be reproduced by adding a delay after
bd_prepare_to_claim() and attempting to mount two partitions of a
disk.

stable: only applicable to v2.6.35

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
14 years agoparisc: pass through '\t' to early (iodc) console
Kyle McMartin [Wed, 4 Aug 2010 00:38:08 +0000 (20:38 -0400)]
parisc: pass through '\t' to early (iodc) console

The firmware handles '\t' internally, so stop trying to emulate it
(which, incidentally, had a bug in it.)

Fixes a really weird hang at bootup in rcu_bootup_announce, which,
as far as I can tell, is the first printk in the core kernel to use
a tab as the first character.

Cc: stable@kernel.org
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael...
Linus Torvalds [Wed, 4 Aug 2010 18:14:36 +0000 (11:14 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rafael/suspend-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Runtime: Add runtime PM statistics (v3)
  PM / Runtime: Make runtime_status attribute not debug-only (v. 2)
  PM: Do not use dynamically allocated objects in pm_wakeup_event()
  PM / Suspend: Fix ordering of calls in suspend error paths
  PM / Hibernate: Fix snapshot error code path
  PM / Hibernate: Fix hibernation_platform_enter()
  pm_qos: Get rid of the allocation in pm_qos_add_request()
  pm_qos: Reimplement using plists
  plist: Add plist_last
  PM: Make it possible to avoid races between wakeup and system sleep
  PNPACPI: Add support for remote wakeup
  PM: describe kernel policy regarding wakeup defaults (v. 2)
  PM / Hibernate: Fix typos in comments in kernel/power/swap.c

14 years agoMerge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
Linus Torvalds [Wed, 4 Aug 2010 18:13:36 +0000 (11:13 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/davej/cpufreq

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Remove pointless printk from p4-clockmod.
  [CPUFREQ] Fix section mismatch for powernow_cpu_init in powernow-k7.c
  [CPUFREQ] Fix section mismatch for longhaul_cpu_init.
  [CPUFREQ] Fix section mismatch for longrun_cpu_init.
  [CPUFREQ] powernow-k8: Fix misleading variable naming
  [CPUFREQ] Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
  [CPUFREQ] arch/x86/kernel/cpu/cpufreq: use for_each_pci_dev()
  [CPUFREQ] fix brace coding style issue.
  [CPUFREQ] x86 cpufreq: Make trace_power_frequency cpufreq driver independent
  [CPUFREQ] acpi-cpufreq: Fix CPU_ANY CPUFREQ_{PRE,POST}CHANGE notification
  [CPUFREQ] ondemand: don't synchronize sample rate unless multiple cpus present
  [CPUFREQ] unexport (un)lock_policy_rwsem* functions
  [CPUFREQ] ondemand: Refactor frequency increase code
  [CPUFREQ] powernow-k8: On load failure, remind the user to enable support in BIOS setup
  [CPUFREQ] powernow-k8: Limit Pstate transition latency check
  [CPUFREQ] Fix PCC driver error path
  [CPUFREQ] fix double freeing in error path of pcc-cpufreq
  [CPUFREQ] pcc driver should check for pcch method before calling _OSC
  [CPUFREQ] fix memory leak in cpufreq_add_dev
  [CPUFREQ] revert "[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)"

Manually fix up non-data merge conflict introduced by new calling
conventions for trace_power_start() in commit 6f4f2723d085 ("x86
cpufreq: Make trace_power_frequency cpufreq driver independent"), which
didn't update the intel_idle native hardware cpuidle driver.

14 years agoMerge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platf...
Linus Torvalds [Wed, 4 Aug 2010 17:44:06 +0000 (10:44 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/mjg59/platform-drivers-x86

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (88 commits)
  ips driver: make it less chatty
  intel_scu_ipc: fix size field for intel_scu_ipc_command
  intel_scu_ipc: return -EIO for error condition in busy_loop
  intel_scu_ipc: fix data packing of PMIC command on Moorestown
  Clean up command packing on MRST.
  zero the stack buffer before giving random garbage to the SCU
  Fix stack buffer size for IPC writev messages
  intel_scu_ipc: Use the new cpu identification function
  intel_scu_ipc: tidy up unused bits
  Remove indirect read write api support.
  intel_scu_ipc: Support Medfield processors
  intel_scu_ipc: detect CPU type automatically
  x86 plat: limit x86 platform driver menu to X86
  acpi ec_sys: Be more cautious about ec write access
  acpi ec: Fix possible double io port registration
  hp-wmi: acpi_drivers.h is already included through acpi.h two lines below
  hp-wmi: Fix mixing up of and/or directive
  dell-laptop: make dell_laptop_i8042_filter() static
  asus-laptop: fix asus_input_init error path
  msi-wmi: make needlessly global symbols static
  ...

14 years agoMerge branch 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Linus Torvalds [Wed, 4 Aug 2010 17:43:01 +0000 (10:43 -0700)]
Merge branch 'kvm-updates/2.6.36' of git://git./virt/kvm/kvm

* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (198 commits)
  KVM: VMX: Fix host GDT.LIMIT corruption
  KVM: MMU: using __xchg_spte more smarter
  KVM: MMU: cleanup spte set and accssed/dirty tracking
  KVM: MMU: don't atomicly set spte if it's not present
  KVM: MMU: fix page dirty tracking lost while sync page
  KVM: MMU: fix broken page accessed tracking with ept enabled
  KVM: MMU: add missing reserved bits check in speculative path
  KVM: MMU: fix mmu notifier invalidate handler for huge spte
  KVM: x86 emulator: fix xchg instruction emulation
  KVM: x86: Call mask notifiers from pic
  KVM: x86: never re-execute instruction with enabled tdp
  KVM: Document KVM_GET_SUPPORTED_CPUID2 ioctl
  KVM: x86: emulator: inc/dec can have lock prefix
  KVM: MMU: Eliminate redundant temporaries in FNAME(fetch)
  KVM: MMU: Validate all gptes during fetch, not just those used for new pages
  KVM: MMU: Simplify spte fetch() function
  KVM: MMU: Add gpte_valid() helper
  KVM: MMU: Add validate_direct_spte() helper
  KVM: MMU: Add drop_large_spte() helper
  KVM: MMU: Use __set_spte to link shadow pages
  ...

14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Linus Torvalds [Wed, 4 Aug 2010 17:41:52 +0000 (10:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
  Input: adp5588-keypad - fix NULL dereference in adp5588_gpio_add()
  Input: cy8ctmg110 - capacitive touchscreen support
  Input: keyboard - also match braille-only keyboards
  Input: adp5588-keys - export unused GPIO pins
  Input: xpad - add product ID for Hori Fighting Stick EX2
  Input: adxl34x - fix leak and use after free
  Input: samsung-keypad - Add samsung keypad driver
  Input: i8042 - reset keyboard controller wehen resuming from S2R
  Input: synaptics - set min/max for finger width
  Input: synaptics - only report width on hardware that supports it
  Input: evdev - signal that device is writable in evdev_poll()
  Input: mousedev - signal that device is writable in mousedev_poll()
  Input: change input handlers to use bool when possible
  Input: document the MT event slot protocol
  Input: introduce MT event slots
  Input: usbtouchscreen - implement reset_resume
  Input: usbtouchscreen - implement runtime power management
  Input: usbtouchscreen - implement basic suspend/resume
  Input: Add ATMEL QT602240 touchscreen driver
  Input: fix signedness warning in input_set_keycode()
  ...

14 years agoMerge branch 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mcheha...
Linus Torvalds [Wed, 4 Aug 2010 17:38:08 +0000 (10:38 -0700)]
Merge branch 'v4l_for_2.6.35' of git://git./linux/kernel/git/mchehab/linux-2.6

* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (243 commits)
  V4L/DVB: sms: Convert IR support to use the Remote Controller core
  V4L/DVB: sms: properly initialize IR phys and IR name
  V4L/DVB: standardize names at rc-dib0700 tables
  V4L/DVB: smsusb: enable IR port for Hauppauge WinTV MiniStick
  V4L/DVB: dib0700: Fix RC protocol logic to properly handle NEC/NECx and RC-5
  V4L/DVB: dib0700: properly implement IR change_protocol
  V4L/DVB: dib0700: break keytable into NEC and RC-5 variants
  V4L/DVB: dib0700: avoid bad repeat
  V4L/DVB: Port dib0700 to rc-core
  V4L/DVB: Add a keymap file with dib0700 table
  V4L/DVB: dvb-usb: add support for rc-core mode
  V4L/DVB: dvb-usb: prepare drivers for using rc-core
  V4L/DVB: dvb-usb: get rid of struct dvb_usb_rc_key
  V4L/DVB: rj54n1cb0c: fix a comment in the driver
  V4L/DVB: V4L2: sh_vou: VOU does support the full PAL resolution too
  V4L/DVB: V4L2: sh_mobile_camera_ceu: add support for CSI2
  V4L/DVB: V4L2: soc-camera: add a MIPI CSI-2 driver for SH-Mobile platforms
  V4L/DVB: V4L2: soc-camera: export soc-camera bus type for notifications
  V4L/DVB: V4L2: mediabus: add 12-bit Bayer and YUV420 pixel formats
  V4L/DVB: mediabus: fix ambiguous pixel code names
  ...

14 years agoMerge branch 'stable/swiotlb-0.8.3' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 4 Aug 2010 17:36:39 +0000 (10:36 -0700)]
Merge branch 'stable/swiotlb-0.8.3' of git://git./linux/kernel/git/konrad/swiotlb-2.6

* 'stable/swiotlb-0.8.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb-2.6:
  swiotlb: Make swiotlb bookkeeping functions visible in the header file.
  swiotlb: search and replace "int dir" with "enum dma_data_direction dir"
  swiotlb: Make internal bookkeeping functions have 'swiotlb_tbl' prefix.
  swiotlb: add the swiotlb initialization function with iotlb memory
  swiotlb: add swiotlb_tbl_map_single library function

14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris...
Linus Torvalds [Wed, 4 Aug 2010 17:28:39 +0000 (10:28 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (90 commits)
  AppArmor: fix build warnings for non-const use of get_task_cred
  selinux: convert the policy type_attr_map to flex_array
  AppArmor: Enable configuring and building of the AppArmor security module
  TOMOYO: Use pathname specified by policy rather than execve()
  AppArmor: update path_truncate method to latest version
  AppArmor: core policy routines
  AppArmor: policy routines for loading and unpacking policy
  AppArmor: mediation of non file objects
  AppArmor: LSM interface, and security module initialization
  AppArmor: Enable configuring and building of the AppArmor security module
  AppArmor: update Maintainer and Documentation
  AppArmor: functions for domain transitions
  AppArmor: file enforcement routines
  AppArmor: userspace interfaces
  AppArmor: dfa match engine
  AppArmor: contexts used in attaching policy to system objects
  AppArmor: basic auditing infrastructure.
  AppArmor: misc. base functions and defines
  TOMOYO: Update version to 2.3.0
  TOMOYO: Fix quota check.
  ...