Junxiao Bi [Fri, 11 Dec 2015 21:41:03 +0000 (13:41 -0800)]
ocfs2: fix SGID not inherited issue
Commit
8f1eb48758aa ("ocfs2: fix umask ignored issue") introduced an
issue, SGID of sub dir was not inherited from its parents dir. It is
because SGID is set into "inode->i_mode" in ocfs2_get_init_inode(), but
is overwritten by "mode" which don't have SGID set later.
Fixes: 8f1eb48758aa ("ocfs2: fix umask ignored issue")
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chen Jie [Fri, 11 Dec 2015 21:41:00 +0000 (13:41 -0800)]
mm/oom_kill.c: avoid attempting to kill init sharing same memory
It's possible that an oom killed victim shares an ->mm with the init
process and thus oom_kill_process() would end up trying to kill init as
well.
This has been shown in practice:
Out of memory: Kill process 9134 (init) score 3 or sacrifice child
Killed process 9134 (init) total-vm:1868kB, anon-rss:84kB, file-rss:572kB
Kill process 1 (init) sharing same memory
...
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
And this will result in a kernel panic.
If a process is forked by init and selected for oom kill while still
sharing init_mm, then it's likely this system is in a recoverable state.
However, it's better not to try to kill init and allow the machine to
panic due to unkillable processes.
[rientjes@google.com: rewrote changelog]
[akpm@linux-foundation.org: fix inverted test, per Ben]
Signed-off-by: Chen Jie <chenjie6@huawei.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seth Jennings [Fri, 11 Dec 2015 21:40:57 +0000 (13:40 -0800)]
drivers/base/memory.c: prohibit offlining of memory blocks with missing sections
Commit
bdee237c0343 ("x86: mm: Use 2GB memory block size on large-memory
x86-64 systems") and
982792c782ef ("x86, mm: probe memory block size for
generic x86 64bit") introduced large block sizes for x86. This made it
possible to have multiple sections per memory block where previously,
there was a only every one section per block.
Since blocks consist of contiguous ranges of section, there can be holes
in the blocks where sections are not present. If one attempts to
offline such a block, a crash occurs since the code is not designed to
deal with this.
This patch is a quick fix to gaurd against the crash by not allowing
blocks with non-present sections to be offlined.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=107781
Signed-off-by: Seth Jennings <sjennings@variantweb.net>
Reported-by: Andrew Banman <abanman@sgi.com>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Fri, 11 Dec 2015 21:40:55 +0000 (13:40 -0800)]
tmpfs: fix shmem_evict_inode() warnings on i_blocks
Dmitry Vyukov provides a little program, autogenerated by syzkaller,
which races a fault on a mapping of a sparse memfd object, against
truncation of that object below the fault address: run repeatedly for a
few minutes, it reliably generates shmem_evict_inode()'s
WARN_ON(inode->i_blocks).
(But there's nothing specific to memfd here, nor to the fstat which it
happened to use to generate the fault: though that looked suspicious,
since a shmem_recalc_inode() had been added there recently. The same
problem can be reproduced with open+unlink in place of memfd_create, and
with fstatfs in place of fstat.)
v3.7 commit
0f3c42f522dc ("tmpfs: change final i_blocks BUG to WARNING")
explains one cause of such a warning (a race with shmem_writepage to
swap), and possible solutions; but we never took it further, and this
syzkaller incident turns out to have a different cause.
shmem_getpage_gfp()'s error recovery, when a freshly allocated page is
then found to be beyond eof, looks plausible - decrementing the alloced
count that was just before incremented - but in fact can go wrong, if a
racing thread (the truncator, for example) gets its shmem_recalc_inode()
in just after our delete_from_page_cache(). delete_from_page_cache()
decrements nrpages, that shmem_recalc_inode() will balance the books by
decrementing alloced itself, then our decrement of alloced take it one
too low: leading to the WARNING when the object is finally evicted.
Once the new page has been exposed in the page cache,
shmem_getpage_gfp() must leave it to shmem_recalc_inode() itself to get
the accounting right in all cases (and not fall through from "trunc:" to
"decused:"). Adjust that error recovery block; and the reinitialization
of info and sbinfo can be removed too.
While we're here, fix shmem_writepage() to avoid the original issue: it
will be safe against a racing shmem_recalc_inode(), if it merely
increments swapped before the shmem_delete_from_page_cache() which
decrements nrpages (but it must then do its own shmem_recalc_inode()
before that, while still in balance, instead of after). (Aside: why do
we shmem_recalc_inode() here in the swap path? Because its raison d'etre
is to cope with clean sparse shmem pages being reclaimed behind our
back: so here when swapping is a good place to look for that case.) But
I've not now managed to reproduce this bug, even without the patch.
I don't see why I didn't do that earlier: perhaps inhibited by the
preference to eliminate shmem_recalc_inode() altogether. Driven by this
incident, I do now have a patch to do so at last; but still want to sit
on it for a bit, there's a couple of questions yet to be resolved.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Fri, 11 Dec 2015 21:40:52 +0000 (13:40 -0800)]
mm/hugetlb.c: fix resv map memory leak for placeholder entries
Dmitry Vyukov reported the following memory leak
unreferenced object 0xffff88002eaafd88 (size 32):
comm "a.out", pid 5063, jiffies
4295774645 (age 15.810s)
hex dump (first 32 bytes):
28 e9 4e 63 00 88 ff ff 28 e9 4e 63 00 88 ff ff (.Nc....(.Nc....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
kmalloc include/linux/slab.h:458
region_chg+0x2d4/0x6b0 mm/hugetlb.c:398
__vma_reservation_common+0x2c3/0x390 mm/hugetlb.c:1791
vma_needs_reservation mm/hugetlb.c:1813
alloc_huge_page+0x19e/0xc70 mm/hugetlb.c:1845
hugetlb_no_page mm/hugetlb.c:3543
hugetlb_fault+0x7a1/0x1250 mm/hugetlb.c:3717
follow_hugetlb_page+0x339/0xc70 mm/hugetlb.c:3880
__get_user_pages+0x542/0xf30 mm/gup.c:497
populate_vma_page_range+0xde/0x110 mm/gup.c:919
__mm_populate+0x1c7/0x310 mm/gup.c:969
do_mlock+0x291/0x360 mm/mlock.c:637
SYSC_mlock2 mm/mlock.c:658
SyS_mlock2+0x4b/0x70 mm/mlock.c:648
Dmitry identified a potential memory leak in the routine region_chg,
where a region descriptor is not free'ed on an error path.
However, the root cause for the above memory leak resides in region_del.
In this specific case, a "placeholder" entry is created in region_chg.
The associated page allocation fails, and the placeholder entry is left
in the reserve map. This is "by design" as the entry should be deleted
when the map is released. The bug is in the region_del routine which is
used to delete entries within a specific range (and when the map is
released). region_del did not handle the case where a placeholder entry
exactly matched the start of the range range to be deleted. In this
case, the entry would not be deleted and leaked. The fix is to take
these special placeholder entries into account in region_del.
The region_chg error path leak is also fixed.
Fixes: feba16e25a57 ("mm/hugetlb: add region_del() to delete a specific range of entries")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org> [4.3+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Fri, 11 Dec 2015 21:40:49 +0000 (13:40 -0800)]
mm: hugetlb: call huge_pte_alloc() only if ptep is null
Currently at the beginning of hugetlb_fault(), we call huge_pte_offset()
and check whether the obtained *ptep is a migration/hwpoison entry or
not. And if not, then we get to call huge_pte_alloc(). This is racy
because the *ptep could turn into migration/hwpoison entry after the
huge_pte_offset() check. This race results in BUG_ON in
huge_pte_alloc().
We don't have to call huge_pte_alloc() when the huge_pte_offset()
returns non-NULL, so let's fix this bug with moving the code into else
block.
Note that the *ptep could turn into a migration/hwpoison entry after
this block, but that's not a problem because we have another
!pte_present check later (we never go into hugetlb_no_page() in that
case.)
Fixes: 290408d4a250 ("hugetlb: hugepage migration core")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: <stable@vger.kernel.org> [2.6.36+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Wilson [Fri, 11 Dec 2015 21:40:46 +0000 (13:40 -0800)]
kernel: remove stop_machine() Kconfig dependency
Currently the full stop_machine() routine is only enabled on SMP if
module unloading is enabled, or if the CPUs are hotpluggable. This
leads to configurations where stop_machine() is broken as it will then
only run the callback on the local CPU with irqs disabled, and not stop
the other CPUs or run the callback on them.
For example, this breaks MTRR setup on x86 in certain configs since
ea8596bb2d8d379 ("kprobes/x86: Remove unused text_poke_smp() and
text_poke_smp_batch() functions") as the MTRR is only established on the
boot CPU.
This patch removes the Kconfig option for STOP_MACHINE and uses the SMP
and HOTPLUG_CPU config options to compile the correct stop_machine() for
the architecture, removing the false dependency on MODULE_UNLOAD in the
process.
Link: https://lkml.org/lkml/2014/10/8/124
References: https://bugs.freedesktop.org/show_bug.cgi?id=84794
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Pranith Kumar <bobby.prani@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Iulia Manda <iulia.manda21@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chuck Ebbert <cebbert.lkml@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Iooss [Fri, 11 Dec 2015 21:40:43 +0000 (13:40 -0800)]
mm: kmemleak: mark kmemleak_init prototype as __init
The kmemleak_init() definition in mm/kmemleak.c is marked __init but its
prototype in include/linux/kmemleak.h is marked __ref since commit
a6186d89c913 ("kmemleak: Mark the early log buffer as __initdata").
This causes a section mismatch which is reported as a warning when
building with clang -Wsection, because kmemleak_init() is declared in
section .ref.text but defined in .init.text.
Fix this by marking kmemleak_init() prototype __init.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Fri, 11 Dec 2015 21:40:40 +0000 (13:40 -0800)]
mm: fix kerneldoc on mem_cgroup_replace_page
Whoops, I missed removing the kerneldoc comment of the lrucare arg
removed from mem_cgroup_replace_page; but it's a good comment, keep it.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Fri, 11 Dec 2015 21:40:38 +0000 (13:40 -0800)]
osd fs: __r4w_get_page rely on PageUptodate for uptodate
Commit
42cb14b110a5 ("mm: migrate dirty page without
clear_page_dirty_for_io etc") simplified the migration of a PageDirty
pagecache page: one stat needs moving from zone to zone and that's about
all.
It's convenient and safest for it to shift the PageDirty bit from old
page to new, just before updating the zone stats: before copying data
and marking the new PageUptodate. This is all done while both pages are
isolated and locked, just as before; and just as before, there's a
moment when the new page is visible in the radix_tree, but not yet
PageUptodate. What's new is that it may now be briefly visible as
PageDirty before it is PageUptodate.
When I scoured the tree to see if this could cause a problem anywhere,
the only places I found were in two similar functions __r4w_get_page():
which look up a page with find_get_page() (not using page lock), then
claim it's uptodate if it's PageDirty or PageWriteback or PageUptodate.
I'm not sure whether that was right before, but now it might be wrong
(on rare occasions): only claim the page is uptodate if PageUptodate.
Or perhaps the page in question could never be migratable anyway?
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Boaz Harrosh <ooo@electrozaur.com>
Cc: Benny Halevy <bhalevy@panasas.com>
Cc: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 11 Dec 2015 21:40:35 +0000 (13:40 -0800)]
MAINTAINERS: make Vladimir co-maintainer of the memory controller
Vladimir architected and authored much of the current state of the
memcg's slab memory accounting and tracking. Make sure he gets CC'd on
bug reports ;-)
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 11 Dec 2015 21:40:32 +0000 (13:40 -0800)]
mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress
Tetsuo Handa has reported that the system might basically livelock in
OOM condition without triggering the OOM killer.
The issue is caused by internal dependency of the direct reclaim on
vmstat counter updates (via zone_reclaimable) which are performed from
the workqueue context. If all the current workers get assigned to an
allocation request, though, they will be looping inside the allocator
trying to reclaim memory but zone_reclaimable can see stalled numbers so
it will consider a zone reclaimable even though it has been scanned way
too much. WQ concurrency logic will not consider this situation as a
congested workqueue because it relies that worker would have to sleep in
such a situation. This also means that it doesn't try to spawn new
workers or invoke the rescuer thread if the one is assigned to the
queue.
In order to fix this issue we need to do two things. First we have to
let wq concurrency code know that we are in trouble so we have to do a
short sleep. In order to prevent from issues handled by
0e093d99763e
("writeback: do not sleep on the congestion queue if there are no
congested BDIs or if significant congestion is not being encountered in
the current zone") we limit the sleep only to worker threads which are
the ones of the interest anyway.
The second thing to do is to create a dedicated workqueue for vmstat and
mark it WQ_MEM_RECLAIM to note it participates in the reclaim and to
have a spare worker thread for it.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Tejun Heo <tj@kernel.org>
Cc: Cristopher Lameter <clameter@sgi.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Arkadiusz Miskiewicz <arekm@maven.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Fri, 11 Dec 2015 21:40:29 +0000 (13:40 -0800)]
mm: fix swapped Movable and Reclaimable in /proc/pagetypeinfo
Commit
016c13daa5c9 ("mm, page_alloc: use masks and shifts when
converting GFP flags to migrate types") has swapped MIGRATE_MOVABLE and
MIGRATE_RECLAIMABLE in the enum definition. However, migratetype_names
wasn't updated to reflect that.
As a result, the file /proc/pagetypeinfo shows the counts for Movable as
Reclaimable and vice versa.
Additionally, commit
0aaa29a56e4f ("mm, page_alloc: reserve pageblocks
for high-order atomic allocations on demand") introduced
MIGRATE_HIGHATOMIC, but did not add a letter to distinguish it into
show_migration_types(), so it doesn't appear in the listing of free
areas during page alloc failures or oom kills.
This patch fixes both problems. The atomic reserves will show with a
letter 'H' in the free areas listings.
Fixes: 016c13daa5c9 ("mm, page_alloc: use masks and shifts when converting GFP flags to migrate types")
Fixes: 0aaa29a56e4f ("mm, page_alloc: reserve pageblocks for high-order atomic allocations on demand")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vladimir Davydov [Fri, 11 Dec 2015 21:40:24 +0000 (13:40 -0800)]
memcg: fix memory.high target
When the memory.high threshold is exceeded, try_charge() schedules a
task_work to reclaim the excess. The reclaim target is set to the
number of pages requested by try_charge().
This is wrong, because try_charge() usually charges more pages than
requested (batch > nr_pages) in order to refill per cpu stocks. As a
result, a process in a cgroup can easily exceed memory.high
significantly when doing a lot of charges w/o returning to userspace
(e.g. reading a file in big chunks).
Fix this issue by assuring that when exceeding memory.high a process
reclaims as many pages as were actually charged (i.e. batch).
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Fri, 11 Dec 2015 21:40:24 +0000 (13:40 -0800)]
mm: hugetlb: fix hugepage memory leak caused by wrong reserve count
When dequeue_huge_page_vma() in alloc_huge_page() fails, we fall back on
alloc_buddy_huge_page() to directly create a hugepage from the buddy
allocator.
In that case, however, if alloc_buddy_huge_page() succeeds we don't
decrement h->resv_huge_pages, which means that successful
hugetlb_fault() returns without releasing the reserve count. As a
result, subsequent hugetlb_fault() might fail despite that there are
still free hugepages.
This patch simply adds decrementing code on that code path.
I reproduced this problem when testing v4.3 kernel in the following situation:
- the test machine/VM is a NUMA system,
- hugepage overcommiting is enabled,
- most of hugepages are allocated and there's only one free hugepage
which is on node 0 (for example),
- another program, which calls set_mempolicy(MPOL_BIND) to bind itself to
node 1, tries to allocate a hugepage,
- the allocation should fail but the reserve count is still hold.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: <stable@vger.kernel.org> [3.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Helge Deller [Sun, 6 Dec 2015 20:25:20 +0000 (21:25 +0100)]
parisc: Disable huge pages on Mako machines
Mako-based machines (PA8800 and PA8900 CPUs) don't allow aliasing on
non-equaivalent addresses.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Sun, 6 Dec 2015 20:56:26 +0000 (21:56 +0100)]
parisc: Wire up mlock2 syscall
Signed-off-by: Helge Deller <deller@gmx.de>
Bjorn Helgaas [Tue, 1 Dec 2015 16:41:47 +0000 (10:41 -0600)]
parisc: Remove unused pcibios_init_bus()
There are no callers of pcibios_init_bus(), so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Mikulas Patocka [Mon, 30 Nov 2015 19:47:46 +0000 (14:47 -0500)]
parisc iommu: fix panic due to trying to allocate too large region
When using the Promise TX2+ SATA controller on PA-RISC, the system often
crashes with kernel panic, for example just writing data with the dd
utility will make it crash.
Kernel panic - not syncing: drivers/parisc/sba_iommu.c: I/O MMU @
000000000000a000 is out of mapping resources
CPU: 0 PID: 18442 Comm: mkspadfs Not tainted 4.4.0-rc2 #2
Backtrace:
[<
000000004021497c>] show_stack+0x14/0x20
[<
0000000040410bf0>] dump_stack+0x88/0x100
[<
000000004023978c>] panic+0x124/0x360
[<
0000000040452c18>] sba_alloc_range+0x698/0x6a0
[<
0000000040453150>] sba_map_sg+0x260/0x5b8
[<
000000000c18dbb4>] ata_qc_issue+0x264/0x4a8 [libata]
[<
000000000c19535c>] ata_scsi_translate+0xe4/0x220 [libata]
[<
000000000c19a93c>] ata_scsi_queuecmd+0xbc/0x320 [libata]
[<
0000000040499bbc>] scsi_dispatch_cmd+0xfc/0x130
[<
000000004049da34>] scsi_request_fn+0x6e4/0x970
[<
00000000403e95a8>] __blk_run_queue+0x40/0x60
[<
00000000403e9d8c>] blk_run_queue+0x3c/0x68
[<
000000004049a534>] scsi_run_queue+0x2a4/0x360
[<
000000004049be68>] scsi_end_request+0x1a8/0x238
[<
000000004049de84>] scsi_io_completion+0xfc/0x688
[<
0000000040493c74>] scsi_finish_command+0x17c/0x1d0
The cause of the crash is not exhaustion of the IOMMU space, there is
plenty of free pages. The function sba_alloc_range is called with size
0x11000, thus the pages_needed variable is 0x11. The function
sba_search_bitmap is called with bits_wanted 0x11 and boundary size is
0x10 (because dma_get_seg_boundary(dev) returns 0xffff).
The function sba_search_bitmap attempts to allocate 17 pages that must not
cross 16-page boundary - it can't satisfy this requirement
(iommu_is_span_boundary always returns true) and fails even if there are
many free entries in the IOMMU space.
How did it happen that we try to allocate 17 pages that don't cross
16-page boundary? The cause is in the function iommu_coalesce_chunks. This
function tries to coalesce adjacent entries in the scatterlist. The
function does several checks if it may coalesce one entry with the next,
one of those checks is this:
if (startsg->length + dma_len > max_seg_size)
break;
When it finishes coalescing adjacent entries, it allocates the mapping:
sg_dma_len(contig_sg) = dma_len;
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
sg_dma_address(contig_sg) =
PIDE_FLAG
| (iommu_alloc_range(ioc, dev, dma_len) << IOVP_SHIFT)
| dma_offset;
It is possible that (startsg->length + dma_len > max_seg_size) is false
(we are just near the 0x10000 max_seg_size boundary), so the funcion
decides to coalesce this entry with the next entry. When the coalescing
succeeds, the function performs
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
And now, because of non-zero dma_offset, dma_len is greater than 0x10000.
iommu_alloc_range (a pointer to sba_alloc_range) is called and it attempts
to allocate 17 pages for a device that must not cross 16-page boundary.
To fix the bug, we must make sure that dma_len after addition of
dma_offset and alignment doesn't cross the segment boundary. I.e. change
if (startsg->length + dma_len > max_seg_size)
break;
to
if (ALIGN(dma_len + dma_offset + startsg->length, IOVP_SIZE) > max_seg_size)
break;
This patch makes this change (it precalculates max_seg_boundary at the
beginning of the function iommu_coalesce_chunks). I also added a check
that the mapping length doesn't exceed dma_get_seg_boundary(dev) (it is
not needed for Promise TX2+ SATA, but it may be needed for other devices
that have dma_get_seg_boundary lower than dma_get_max_seg_size).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
David S. Miller [Sat, 12 Dec 2015 05:43:44 +0000 (00:43 -0500)]
Merge branch 'mpls-fixes'
Robert Shearman says:
====================
mpls: fixes for nexthops without via addresses
These four fixes all apply to the case of having an mpls route with an
output device, but without a nexthop.
Patches 2 and 3 could really have been combined in one patch, but I
wanted to separate the fix for some recent breakage from the fix for a
day-1 issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Thu, 10 Dec 2015 19:30:51 +0000 (19:30 +0000)]
mpls: make via address optional for multipath routes
The via address is optional for a single path route, yet is mandatory
when the multipath attribute is used:
# ip -f mpls route add 100 dev lo
# ip -f mpls route add 101 nexthop dev lo
RTNETLINK answers: Invalid argument
Make them consistent by making the via address optional when the
RTA_MULTIPATH attribute is being parsed so that both forms of
specifying the route work.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Thu, 10 Dec 2015 19:30:50 +0000 (19:30 +0000)]
mpls: fix out-of-bounds access when via address not specified
When a via address isn't specified, the via table is left initialised
to 0 (NEIGH_ARP_TABLE), and the via address length also left
initialised to 0. This results in a via address array of length 0
being allocated (contiguous with route and nexthop array), meaning
that when a packet is sent using neigh_xmit the neighbour lookup and
creation will cause an out-of-bounds access when accessing the 4 bytes
of the IPv4 address it assumes it has been given a pointer to.
This could be fixed by allocating the 4 bytes of via address necessary
and leaving it as all zeroes. However, it seems wrong to me to use an
ipv4 nexthop (including possibly ARPing for 0.0.0.0) when the user
didn't specify to do so.
Instead, set the via address table to NEIGH_NR_TABLES to signify it
hasn't been specified and use this at forwarding time to signify a
neigh_xmit using an L2 address consisting of the device address. This
mechanism is the same as that used for both ARP and ND for loopback
interfaces and those flagged as no-arp, which are all we can really
support in this case.
Fixes: cf4b24f0024f ("mpls: reduce memory usage of routes")
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Thu, 10 Dec 2015 19:30:49 +0000 (19:30 +0000)]
mpls: don't dump RTA_VIA attribute if not specified
The problem seen is that when adding a route with a nexthop with no
via address specified, iproute2 generates bogus output:
# ip -f mpls route add 100 dev lo
# ip -f mpls route list
100 via inet 0.0.8.0 dev lo
The reason for this is that the kernel generates an RTA_VIA attribute
with the family set to AF_INET, but the via address data having zero
length. The cause of family being AF_INET is that on route insert
cfg->rc_via_table is left set to 0, which just happens to be
NEIGH_ARP_TABLE which is then translated into AF_INET.
iproute2 doesn't validate the length prior to printing and so prints
garbage. Although it could be fixed to do the validation, I would
argue that AF_INET addresses should always be exactly 4 bytes so the
kernel is really giving userspace bogus data.
Therefore, avoid generating the RTA_VIA attribute when dumping the
route if the via address wasn't specified on add/modify. This is
indicated by NEIGH_ARP_TABLE and a zero via address length - if the
user specified a via address the address length would have been
validated such that it was 4 bytes. Although this is a change in
behaviour that is visible to userspace, I believe that what was
generated before was invalid and as such userspace wouldn't be
expecting it.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Thu, 10 Dec 2015 19:30:48 +0000 (19:30 +0000)]
mpls: validate L2 via address length
If an L2 via address for an mpls nexthop is specified, the length of
the L2 address must match that expected by the output device,
otherwise it could access memory beyond the end of the via address
buffer in the route.
This check was present prior to commit
f8efb73c97e2 ("mpls: multipath
route support"), but got lost in the refactoring, so add it back,
applying it to all nexthops in multipath routes.
Fixes: f8efb73c97e2 ("mpls: multipath route support")
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Fri, 11 Dec 2015 09:39:32 +0000 (09:39 +0000)]
sfc: only use RSS filters if we're using RSS
Without this, filter insertion on a VF would fail if only one channel
was in use. This would include the unicast station filter and therefore
no traffic would be received.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 10 Dec 2015 17:14:20 +0000 (09:14 -0800)]
uapi: export ila.h
The file ila.h used for lightweight tunnels is being used by iproute2
but is not exported yet.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 12 Dec 2015 04:34:06 +0000 (23:34 -0500)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: Bug fix and add tx timeout recovery.
Fix a bitmap declaration bug and add missing tx timeout recovery.
v2: Fixed white space error. Thanks Dave.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 10 Dec 2015 00:35:44 +0000 (19:35 -0500)]
bnxt_en: Implement missing tx timeout reset logic.
The reset logic calls bnxt_close_nic() and bnxt_open_nic() under rtnl_lock
from bnxt_sp_task. BNXT_STATE_IN_SP_TASK must be cleared before calling
bnxt_close_nic() to avoid deadlock.
v2: Fixed white space error. Thanks Dave.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 10 Dec 2015 00:35:43 +0000 (19:35 -0500)]
bnxt_en: Don't cancel sp_task from bnxt_close_nic().
When implementing driver reset from tx_timeout in the next patch,
bnxt_close_nic() will be called from the sp_task workqueue. Calling
cancel_work() on sp_task will hang the workqueue.
Instead, set a new bit BNXT_STATE_IN_SP_TASK when bnxt_sp_task() is running.
bnxt_close_nic() will wait for BNXT_STATE_IN_SP_TASK to clear before
proceeding.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 10 Dec 2015 00:35:42 +0000 (19:35 -0500)]
bnxt_en: Change bp->state to bitmap.
This allows multiple independent bits to be set for various states.
Subsequent patches to implement tx timeout reset will require this.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 10 Dec 2015 00:35:41 +0000 (19:35 -0500)]
bnxt_en: Fix bitmap declaration to work on 32-bit arches.
The declaration of the bitmap vf_req_snif_bmap using fixed array of
unsigned long will only work on 64-bit archs. Use DECLARE_BITMAP instead
which will work on all archs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Wed, 9 Dec 2015 22:07:40 +0000 (14:07 -0800)]
openvswitch: Respect conntrack zone even if invalid
If userspace executes ct(zone=1), and the connection tracker determines
that the packet is invalid, then the ct_zone flow key field is populated
with the default zone rather than the zone that was specified. Even
though connection tracking failed, this field should be updated with the
value that the action specified. Fix the issue.
Fixes: 7f8a436eaa2c ("openvswitch: Add conntrack action")
Signed-off-by: Joe Stringer <joe@ovn.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Wed, 9 Dec 2015 22:07:39 +0000 (14:07 -0800)]
openvswitch: Fix helper reference leak
If the actions (re)allocation fails, or the actions list is larger than the
maximum size, and the conntrack action is the last action when these
problems are hit, then references to helper modules may be leaked. Fix
the issue.
Fixes: cae3a2627520 ("openvswitch: Allow attaching helpers to ct action")
Signed-off-by: Joe Stringer <joe@ovn.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 9 Dec 2015 18:56:31 +0000 (19:56 +0100)]
phy: micrel: Fix finding PHY properties in MAC node.
commit
8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus,
not the bus' parent.") changed the parenting of PHY devices, making
them a child of the MDIO bus, instead of the MAC device. This broken
the Micrel PHY driver which has a deprecated feature of allowing PHY
properties to be placed into the MAC node.
In order to find the MAC node, we need to walk up the tree of devices
until we find one with an OF node attached.
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Suggested-by: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Fixes: 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 9 Dec 2015 15:25:06 +0000 (07:25 -0800)]
ipv6: sctp: clone options to avoid use after free
SCTP is lacking proper np->opt cloning at accept() time.
TCP and DCCP use ipv6_dup_options() helper, do the same
in SCTP.
We might later factorize this code in a common helper to avoid
future mistakes.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 8 Dec 2015 15:22:02 +0000 (07:22 -0800)]
xfrm: add rcu protection to sk->sk_policy[]
XFRM can deal with SYNACK messages, sent while listener socket
is not locked. We add proper rcu protection to __xfrm_sk_clone_policy()
and xfrm_sk_policy_lookup()
This might serve as the first step to remove xfrm.xfrm_policy_lock
use in fast path.
Fixes: fa76ce7328b2 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 8 Dec 2015 15:22:01 +0000 (07:22 -0800)]
xfrm: add rcu grace period in xfrm_policy_destroy()
We will soon switch sk->sk_policy[] to RCU protection,
as SYNACK packets are sent while listener socket is not locked.
This patch simply adds RCU grace period before struct xfrm_policy
freeing, and the corresponding rcu_head in struct xfrm_policy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hilman [Sat, 12 Dec 2015 00:14:34 +0000 (16:14 -0800)]
Merge tag 'imx-fixes-4.4-2' of git://git./linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 4.4, 2nd round" from Shawn Guo:
The i.MX fixes for 4.4, 2nd round:
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
* tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
Liu Gang [Fri, 4 Dec 2015 22:55:05 +0000 (16:55 -0600)]
ls2080a/dts: Add little endian property for GPIO IP block
The GPIO block for ls2080a platform has little endian registers,
the GPIO driver needs this property to read/write registers by
right interface.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Li Yang [Fri, 4 Dec 2015 22:55:04 +0000 (16:55 -0600)]
dt-bindings: define little-endian property for QorIQ GPIO
The GPIO block on different QorIQ chips could have registers in different
endianess. Define the property to specify which endian is used by the
hardware.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
yangbo lu [Fri, 4 Dec 2015 22:55:03 +0000 (16:55 -0600)]
ARM64: dts: ls2080a: fix eSDHC endianness
Add the "little-endian" property to fix the issue that eSDHC
is not working and dumping out "mmc0: Controller never released
inhibit bit(s)." error messages constantly.
Fixes: 5461597f6ce0 ("dts/ls2080a: Update DTSI to add support of various peripherals")
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Alan Stern [Thu, 10 Dec 2015 20:27:21 +0000 (15:27 -0500)]
USB: add quirk for devices with broken LPM
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 11 Dec 2015 12:38:06 +0000 (14:38 +0200)]
xhci: fix usb2 resume timing and races.
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Khoroshilov [Fri, 11 Dec 2015 20:24:10 +0000 (23:24 +0300)]
nfit: acpi_nfit_notify(): Do not leave device locked
Even if dev->driver is null because we are being removed,
it is safer to not leave device locked.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Linus Torvalds [Fri, 11 Dec 2015 19:00:30 +0000 (11:00 -0800)]
Merge tag 'dm-4.4-fixes-2' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Five stable fixes:
- Two DM btree bufio buffer leak fixes that resolve reported BUG_ONs
during DM thinp metadata close's dm_bufio_client_destroy().
- A DM thinp range discard fix to handle discarding a partially
mapped range.
- A DM thinp metadata snapshot fix to make sure the btree roots saved
in the metadata snapshot are the most current.
- A DM space map metadata refcounting fix that improves both DM thinp
and DM cache metadata"
* tag 'dm-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree: fix bufio buffer leaks in dm_btree_del() error path
dm space map metadata: fix ref counting bug when bootstrapping a new space map
dm thin metadata: fix bug when taking a metadata snapshot
dm thin metadata: fix bug in dm_thin_remove_range()
dm btree: fix leak of bufio-backed block in btree_split_sibling error path
Linus Torvalds [Fri, 11 Dec 2015 18:56:41 +0000 (10:56 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"Two bugfixes, both bound for -stable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: break infinite loop in fuse_fill_write_pages()
cuse: fix memory leak
Linus Torvalds [Fri, 11 Dec 2015 18:51:02 +0000 (10:51 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Not too much this time.
- One nouveau workaround extended to a few more GPUs
- Some amdgpu big endian fixes, and a regression fixer
- Some vmwgfx fixes
- One ttm locking fix
- One vgaarb fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
vgaarb: fix signal handling in vga_get()
radeon: Fix VCE IB test on Big-Endian systems
radeon: Fix VCE ring test for Big-Endian systems
radeon/cik: Fix GFX IB test on Big-Endian
drm/amdgpu: fix the lost duplicates checking
drm/nouveau/pmu: remove whitelist for PGOB-exit WAR, enable by default
drm/vmwgfx: Implement the cursor_set2 callback v2
drm/vmwgfx: fix a warning message
drm/ttm: Fixed a read/write lock imbalance
Catalin Marinas [Tue, 8 Dec 2015 17:39:15 +0000 (17:39 +0000)]
arm64: Improve error reporting on set_pte_at() checks
Currently the BUG_ON() checks do not give enough information about the
PTEs being set. This patch changes BUG_ON to WARN_ONCE and dumps the
values of the old and new PTEs. In addition, the checks are only made if
the new PTE entry is valid.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Stefan Agner [Tue, 1 Dec 2015 01:59:26 +0000 (17:59 -0800)]
ARM: dts: vf610: use reset values for L2 cache latencies
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Kirill A. Shutemov [Mon, 30 Nov 2015 02:17:31 +0000 (04:17 +0200)]
vgaarb: fix signal handling in vga_get()
There are few defects in vga_get() related to signal hadning:
- we shouldn't check for pending signals for TASK_UNINTERRUPTIBLE
case;
- if we found pending signal we must remove ourself from wait queue
and change task state back to running;
- -ERESTARTSYS is more appropriate, I guess.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: stable@vger.kernel.org
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 11 Dec 2015 04:04:09 +0000 (14:04 +1000)]
Merge branch 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
some big endian fixes and one regression fix.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
radeon: Fix VCE IB test on Big-Endian systems
radeon: Fix VCE ring test for Big-Endian systems
radeon/cik: Fix GFX IB test on Big-Endian
drm/amdgpu: fix the lost duplicates checking
Arnd Bergmann [Thu, 10 Dec 2015 23:42:22 +0000 (00:42 +0100)]
Merge tag 'omap-for-v4.4/fixes-rc4' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.4-rc4" from Tony Lindgren
Few fixes for omaps for v4.4-rc cycle:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
* tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
Arnd Bergmann [Wed, 9 Dec 2015 14:11:12 +0000 (15:11 +0100)]
ARM: pxa: use PWM lookup table for all machines
The recent change to use a pwm lookup table for the ezx machines
was incomplete and only changed the a780 model, but not the
other ones in the same file.
This adds the missing calls to pwm_add_table().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c3322022897c ("ARM: pxa: ezx: Use PWM lookup table")
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Arnd Bergmann [Thu, 10 Dec 2015 23:24:38 +0000 (00:24 +0100)]
Merge tag 'berlin-fixes-for-4.4-rc1-1' of git://git.infradead.org/users/hesselba/linux-berlin into fixes
Merge "Marvell Berlin fixes for 4.4-rc1 (round 1)" from Sebastian Hesselbarth:
- fix wrong SDIO DT clocks on BG2Q
* tag 'berlin-fixes-for-4.4-rc1-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
Arnd Bergmann [Thu, 10 Dec 2015 23:22:11 +0000 (00:22 +0100)]
Merge tag 'at91-4.4-fixes-2' of git://git./linux/kernel/git/abelloni/linux into fixes
Merge "Second fixes for 4.4" from Alexandre Belloni:
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
* tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
Arnd Bergmann [Thu, 10 Dec 2015 23:19:37 +0000 (00:19 +0100)]
Merge tag 'samsung-fixes-4.4' of https://git./linux/kernel/git/krzk/linux into fixes
Merge "Fixes for Exynos" from Krzysztof Kozlowski:
1. Fix potential NULL pointer dereference in Exynos PMU driver.
2. Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
* tag 'samsung-fixes-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
Linus Torvalds [Thu, 10 Dec 2015 22:42:22 +0000 (14:42 -0800)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Most are minor to important fixes.
There is one performance enhancement that I took on the grounds that
failing to check if other processes can run before running what's
intended to be a background, idle-time task is a bug, even though the
primary effect of the fix is to improve performance (and it was a very
simple patch)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx5: Postpone remove_keys under knowledge of coming preemption
IB/mlx4: Use vmalloc for WR buffers when needed
IB/mlx4: Use correct order of variables in log message
iser-target: Remove explicit mlx4 work-around
mlx4: Expose correct max_sge_rd limit
IB/mad: Require CM send method for everything except ClassPortInfo
IB/cma: Add a missing rcu_read_unlock()
IB core: Fix ib_sg_to_pages()
IB/srp: Fix srp_map_sg_fr()
IB/srp: Fix indirect data buffer rkey endianness
IB/srp: Initialize dma_length in srp_map_idb
IB/srp: Fix possible send queue overflow
IB/srp: Fix a memory leak
IB/sa: Put netlink request into the request list before sending
IB/iser: use sector_div instead of do_div
IB/core: use RCU for uverbs id lookup
IB/qib: Minor fixes to qib per SFF 8636
IB/core: Fix user mode post wr corruption
IB/qib: Fix qib_mr structure
Jisheng Zhang [Mon, 7 Dec 2015 13:09:25 +0000 (21:09 +0800)]
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
We removed CLK_IGNORE_UNUSED from CLKID_SDIO's flag, so the sdhci0 and
sdhci1 don't work. We fix this by adding the optional 2nd clock for
BG2Q's sdhci0 and sdhci1. This patch brings another benefit: the 2nd
clock can be disabled during runtime pm, so saves power a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Jisheng Zhang [Mon, 7 Dec 2015 13:09:24 +0000 (21:09 +0800)]
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
The optional 2nd clock is CLKID_SDIO. We removed CLK_IGNORE_UNUSED
from CLKID_SDIO's flag, so the sdhci2 doesn't work. This patch fixes
this issue by correcting the sdhci2's 2nd clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Linus Torvalds [Thu, 10 Dec 2015 18:44:32 +0000 (10:44 -0800)]
Merge tag 'sound-4.4-rc5' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Again less intensive changes in this rc: you can find only a few
HD-audio fixes (noise fixes for Intel Broxton chip and a few Thinkpad
models, quirks for Alienware 17 and Packard Bell DOTS) in addition to
a long-standing rme96 bug fix"
* tag 'sound-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/ca0132 - quirk for Alienware 17 2015
ALSA: hda - Fix noise problems on Thinkpad T440s
ALSA: hda - Fixing speaker noise on the two latest thinkpad models
ALSA: hda - Add inverted dmic for Packard Bell DOTS
ALSA: hda - Fix playback noise with 24/32 bit sample size on BXT
ALSA: rme96: Fix unexpected volume reset after rate changes
Linus Walleij [Thu, 10 Dec 2015 17:21:41 +0000 (18:21 +0100)]
clocksource: Mmio: remove artificial 32bit limitation
The EP93xx is registering a clocksource of 40 bits with
clocksource_mmio_init() but this is not working because of this
artificial limitation. It works fine to lift the uppe limit to
64 bits, and since cycle_t is u64, it should intuitively have been
like that from the beginning.
Fixes: 000bc17817bf "ARM: ep93xx: switch to GENERIC_CLOCKEVENTS"
Reported-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1449768101-6879-1-git-send-email-linus.walleij@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Marc Zyngier [Mon, 7 Dec 2015 10:11:12 +0000 (10:11 +0000)]
irqchip/gic-v3: Add missing include for barrier.h
Both the 32bit and 64bit versions of the GICv3 header file are using
barriers, but neglect to include barrier.h, leading to an interesting
splat in some circumstances.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1449483072-17694-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Marc Zyngier [Mon, 7 Dec 2015 10:11:11 +0000 (10:11 +0000)]
irqchip/gic-v3: Add missing struct device_node declaration
When the GICv3 header file is used in a C file that doesn't include
any of the OF stuff, we end up with a bunch of ugly warnings.
Let's keep GCC quiet by adding a forward declaration.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1449483072-17694-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pablo Neira Ayuso [Wed, 9 Dec 2015 21:06:59 +0000 (22:06 +0100)]
netfilter: nf_dup: add missing dependencies with NF_CONNTRACK
CONFIG_NF_CONNTRACK=m
CONFIG_NF_DUP_IPV4=y
results in:
net/built-in.o: In function `nf_dup_ipv4':
>> (.text+0xd434f): undefined reference to `nf_conntrack_untracked'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso [Wed, 9 Dec 2015 11:09:56 +0000 (12:09 +0100)]
netfilter: nfnetlink: fix splat due to incorrect socket memory accounting in skbuff clones
If we attach the sk to the skb from nfnetlink_rcv_batch(), then
netlink_skb_destructor() will underflow the socket receive memory
counter and we get warning splat when releasing the socket.
$ cat /proc/net/netlink
sk Eth Pid Groups Rmem Wmem Dump Locks Drops Inode
ffff8800ca903000 12 0
00000000 -54144 0 0 2 0 17942
^^^^^^
Rmem above shows an underflow.
And here below the warning splat:
[ 1363.815976] WARNING: CPU: 2 PID: 1356 at net/netlink/af_netlink.c:958 netlink_sock_destruct+0x80/0xb9()
[...]
[ 1363.816152] CPU: 2 PID: 1356 Comm: kworker/u16:1 Tainted: G W 4.4.0-rc1+ #153
[ 1363.816155] Hardware name: LENOVO 23259H1/23259H1, BIOS G2ET32WW (1.12 ) 05/30/2012
[ 1363.816160] Workqueue: netns cleanup_net
[ 1363.816163]
0000000000000000 ffff880119203dd0 ffffffff81240204 0000000000000000
[ 1363.816169]
ffff880119203e08 ffffffff8104db4b ffffffff813d49a1 ffff8800ca771000
[ 1363.816174]
ffffffff81a42b00 0000000000000000 ffff8800c0afe1e0 ffff880119203e18
[ 1363.816179] Call Trace:
[ 1363.816181] <IRQ> [<
ffffffff81240204>] dump_stack+0x4e/0x79
[ 1363.816193] [<
ffffffff8104db4b>] warn_slowpath_common+0x9a/0xb3
[ 1363.816197] [<
ffffffff813d49a1>] ? netlink_sock_destruct+0x80/0xb9
skb->sk was only needed to lookup for the netns, however we don't need
this anymore since
633c9a840d0b ("netfilter: nfnetlink: avoid recurrent
netns lookups in call_batch") so this patch removes this manual socket
assignment to resolve this problem.
Reported-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Joe Thornber [Thu, 10 Dec 2015 14:37:53 +0000 (14:37 +0000)]
dm btree: fix bufio buffer leaks in dm_btree_del() error path
If dm_btree_del()'s call to push_frame() fails, e.g. due to
btree_node_validator finding invalid metadata, the dm_btree_del() error
path must unlock all frames (which have active dm-bufio buffers) that
were pushed onto the del_stack.
Otherwise, dm_bufio_client_destroy() will BUG_ON() because dm-bufio
buffers have leaked, e.g.:
device-mapper: bufio: leaked buffer 3, hold count 1, list 0
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Pablo Neira Ayuso [Wed, 9 Dec 2015 11:08:26 +0000 (12:08 +0100)]
netfilter: nfnetlink: avoid recurrent netns lookups in call_batch
Pass the net pointer to the call_batch callback functions so we can skip
recurrent lookups.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Maarten Lankhorst [Mon, 23 Nov 2015 09:25:28 +0000 (10:25 +0100)]
drm/i915: Do a better job at disabling primary plane in the noatomic case.
When disable_noatomic is called plane_mask is not correct yet, and
plane_state->visible = true is left as true after disabling the primary
plane.
Other planes are already disabled as part of crtc sanitization, only the
primary is left active. But the plane_mask is not updated here. It gets
updated during fb takeover in modeset_gem_init, or set to the new value
on resume.
This means that to disable the primary plane 1 << drm_plane_index(primary)
needs to be used.
Afterwards because the crtc is no longer active it's forbidden to keep
plane_state->visible set, or a WARN_ON in
intel_plane_atomic_calc_changes triggers. There are other code points
that rely on accurate plane_state->visible too, so make sure the bool is
cleared.
The other planes are already disabled in intel_sanitize_crtc, so they
don't have to be handled here.
Cc: stable@vger.kernel.org #v4.3, v4.2?
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92655
Tested-by: Tomas Mezzadra <tmezzadra@gmail.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/5652DB88.9070208@linux.intel.com
(cherry picked from commit
54a4196188eab82e6f0a5f05716626e9f18b8fb6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Johannes Berg [Thu, 10 Dec 2015 09:37:51 +0000 (10:37 +0100)]
rfkill: copy the name into the rfkill struct
Some users of rfkill, like NFC and cfg80211, use a dynamic name when
allocating rfkill, in those cases dev_name(). Therefore, the pointer
passed to rfkill_alloc() might not be valid forever, I specifically
found the case that the rfkill name was quite obviously an invalid
pointer (or at least garbage) when the wiphy had been renamed.
Fix this by making a copy of the rfkill name in rfkill_alloc().
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cyrille Pitchen [Mon, 7 Dec 2015 14:58:56 +0000 (15:58 +0100)]
dmaengine: at_xdmac: fix at_xdmac_prep_dma_memcpy()
This patch fixes at_xdmac_prep_dma_memcpy(). Indeed the data width field
of the Channel Configuration register was not updated properly in the
loop: the bits of the dwidth field were not cleared before adding their
new value.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee70 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul [Thu, 10 Dec 2015 03:13:43 +0000 (08:43 +0530)]
Merge branch 'fix/edma' into fixes
Peter Ujfalusi [Wed, 9 Dec 2015 08:18:11 +0000 (10:18 +0200)]
dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi [Wed, 9 Dec 2015 08:18:10 +0000 (10:18 +0200)]
dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Linus Torvalds [Thu, 10 Dec 2015 00:52:12 +0000 (16:52 -0800)]
Merge tag 'vfio-v4.4-rc5' of git://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
- Various fixes for removing redundancy, const'ifying structs, avoiding
stack usage, fixing WARN usage (Krzysztof Kozlowski, Julia Lawall,
Kees Cook, Dan Carpenter)
- Revert No-IOMMU mode as the intended user has not emerged (Alex
Williamson)
* tag 'vfio-v4.4-rc5' of git://github.com/awilliam/linux-vfio:
Revert: "vfio: Include No-IOMMU mode"
vfio: fix a warning message
vfio: platform: remove needless stack usage
vfio-pci: constify pci_error_handlers structures
vfio: Drop owner assignment from platform_driver
Grygorii Strashko [Mon, 30 Nov 2015 15:56:38 +0000 (17:56 +0200)]
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit
8cbd4c2f6a99 ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Thu, 10 Dec 2015 00:44:07 +0000 (16:44 -0800)]
Merge tag 'devicetree-fixes-for-4.4-rc4' of git://git./linux/kernel/git/robh/linux
Pull DT fixes from Rob Herring:
"I think this should be all for 4.4:
- Fix incorrect warning about overlapping memory regions
- Export of_irq_find_parent again which was made static in 4.4, but
has users pending for 4.5.
- Fix of_msi_map_rid declaration location
- Fix re-entrancy for of_fdt_unflatten_tree
- Clean-up of phys_addr_t printks"
* tag 'devicetree-fixes-for-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/irq: move of_msi_map_rid declaration to the correct ifdef section
of/irq: Export of_irq_find_parent again
of/fdt: Add mutex protection for calls to __unflatten_device_tree()
of/address: fix typo in comment block of of_translate_one()
of: do not use 0x in front of %pa
of: Fix comparison of reserved memory regions
Linus Torvalds [Thu, 10 Dec 2015 00:36:29 +0000 (16:36 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One small build fix, a couple do_div() fixes, and a fix for the gpio
basic clock type are the major changes here. There's also a couple
fixes for the TI, sunxi, and scpi clock drivers"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi: pll2: Fix clock running too fast
clk: scpi: add missing of_node_put
clk: qoriq: fix memory leak
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
clk: mmp: add linux/clk.h includes
clk: ti: drop locking code from mux/divider drivers
clk: ti816x: Add missing dmtimer clkdev entries
clk: ti: fapll: fix wrong do_div() usage
clk: ti: clkt_dpll: fix wrong do_div() usage
clk: gpio: Get parent clk names in of_gpio_clk_setup()
Linus Torvalds [Wed, 9 Dec 2015 19:57:10 +0000 (11:57 -0800)]
Merge tag 'for-linus-4.4-1' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI fix from Corey Minyard:
"Fix an Oops if an interrupt occurs at startup. This can happen on
some hardware"
* tag 'for-linus-4.4-1' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: move timer init to before irq is setup
Jan Stancek [Tue, 8 Dec 2015 18:57:51 +0000 (13:57 -0500)]
ipmi: move timer init to before irq is setup
We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.
static int smi_start_processing(void *send_info,
ipmi_smi_t intf)
{
/* Try to claim any interrupts. */
if (new_smi->irq_setup)
new_smi->irq_setup(new_smi);
--> IRQ arrives here and irq handler tries to modify uninitialized timer
which triggers BUG_ON(!timer->function) in __mod_timer().
Call Trace:
<IRQ>
[<
ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si]
[<
ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si]
[<
ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si]
[<
ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350
[<
ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si]
[<
ffffffff810efaf0>] handle_IRQ_event+0x60/0x170
[<
ffffffff810f245e>] handle_edge_irq+0xde/0x180
[<
ffffffff8100fc59>] handle_irq+0x49/0xa0
[<
ffffffff8154643c>] do_IRQ+0x6c/0xf0
[<
ffffffff8100ba53>] ret_from_intr+0x0/0x11
/* Set up the timer that drives the interface. */
setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi);
The following patch fixes the problem.
To: Openipmi-developer@lists.sourceforge.net
To: Corey Minyard <minyard@acm.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # Applies cleanly to 3.10-, needs small rework before
Sasha Levin [Fri, 4 Dec 2015 03:04:01 +0000 (22:04 -0500)]
bitops.h: correctly handle rol32 with 0 byte shift
ROL on a 32 bit integer with a shift of 32 or more is undefined and the
result is arch-dependent. Avoid this by handling the trivial case of
roling by 0 correctly.
The trivial solution of checking if shift is 0 breaks gcc's detection
of this code as a ROL instruction, which is unacceptable.
This bug was reported and fixed in GCC
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=57157):
The standard rotate idiom,
(x << n) | (x >> (32 - n))
is recognized by gcc (for concreteness, I discuss only the case that x
is an uint32_t here).
However, this is portable C only for n in the range 0 < n < 32. For n
== 0, we get x >> 32 which gives undefined behaviour according to the
C standard (6.5.7, Bitwise shift operators). To portably support n ==
0, one has to write the rotate as something like
(x << n) | (x >> ((-n) & 31))
And this is apparently not recognized by gcc.
Note that this is broken on older GCCs and will result in slower ROL.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Thornber [Wed, 9 Dec 2015 16:38:12 +0000 (16:38 +0000)]
dm space map metadata: fix ref counting bug when bootstrapping a new space map
When applying block operations (BOPs) do not remove them from the
uncommitted BOP ring-buffer until after they've been applied -- in case
we recurse.
Also, perform BOP_INC operation, in dm_sm_metadata_create() and
sm_metadata_extend(), in terms of the uncommitted BOP ring-buffer rather
than using direct calls to sm_ll_inc().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Joe Thornber [Wed, 9 Dec 2015 16:23:24 +0000 (16:23 +0000)]
dm thin metadata: fix bug when taking a metadata snapshot
When you take a metadata snapshot the btree roots for the mapping and
details tree need to have their reference counts incremented so they
persist for the lifetime of the metadata snap.
The roots being incremented were those currently written in the
superblock, which could possibly be out of date if concurrent IO is
triggering new mappings, breaking of sharing, etc.
Fix this by performing a commit with the metadata lock held while taking
a metadata snapshot.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Greg Kroah-Hartman [Wed, 9 Dec 2015 18:15:30 +0000 (13:15 -0500)]
Merge tag 'fixes-for-v4.4-rc5' of git://git./linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for-v4.4-rc5
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Linus Torvalds [Wed, 9 Dec 2015 17:34:26 +0000 (09:34 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes, both -stable fodder (9p one all way back to 2.6.32,
dio - to all branches where "Fix negative return from dio read beyond
eof" will end up it; it's a fixup to commit marked for -stable)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the regression from "direct-io: Fix negative return from dio read beyond eof"
9p: ->evict_inode() should kick out ->i_data, not ->i_mapping
Linus Torvalds [Wed, 9 Dec 2015 17:26:06 +0000 (09:26 -0800)]
Merge tag 'pci-v4.4-fixes-2' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are more fixes I'd like to have in v4.4. Several for the Altera
driver added for v4.4, and one for an MSI domain problem that affects
several arm64 platforms:
MSI:
- Only use the generic MSI layer when domain is hierarchical (Marc
Zyngier)
Altera host bridge driver:
- Fix loop in tlp_read_packet() (Dan Carpenter)
- Fix Requester ID for config accesses (Ley Foon Tan)
- Check TLP completion status (Ley Foon Tan)
- Fix error when INTx is 4 (Ley Foon Tan)"
* tag 'pci-v4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: altera: Fix error when INTx is 4
PCI: altera: Check TLP completion status
PCI: altera: Fix Requester ID for config accesses
PCI: altera: Fix loop in tlp_read_packet()
PCI/MSI: Only use the generic MSI layer when domain is hierarchical
Gabriele Martino [Wed, 9 Dec 2015 16:05:58 +0000 (17:05 +0100)]
ALSA: hda/ca0132 - quirk for Alienware 17 2015
The Alienware 17 (2015) has the same card and pin configuration of the
Alienware 15, so the same quirks must be applied.
Signed-off-by: Gabriele Martino <g.martino@gmx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Aaro Koskinen [Mon, 23 Nov 2015 19:50:11 +0000 (21:50 +0200)]
usb: musb: fail with error when no DMA controller set
Fail with error when no DMA controller is set.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rob Herring [Wed, 9 Dec 2015 15:11:10 +0000 (09:11 -0600)]
of/irq: move of_msi_map_rid declaration to the correct ifdef section
In checking fixes for of_irq_find_parent declaration location, I found
that of_msi_map_rid is also wrong. of_msi_map_rid is not implemented for
Sparc, so it should not be in the Sparc specific section of the header.
Move it to just depend on OF_IRQ.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Carlo Caione [Tue, 1 Dec 2015 16:24:17 +0000 (17:24 +0100)]
of/irq: Export of_irq_find_parent again
of_irq_find_parent was made static since it had no users outside of
of_irq.c. Export it again since we are going to use it again.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[robh: move of_irq_find_parent to correct ifdef section]
Signed-off-by: Rob Herring <robh@kernel.org>
Takashi Iwai [Wed, 9 Dec 2015 14:17:43 +0000 (15:17 +0100)]
ALSA: hda - Fix noise problems on Thinkpad T440s
Lenovo Thinkpad T440s suffers from constant background noises, and it
seems to be a generic hardware issue on this model:
https://forums.lenovo.com/t5/ThinkPad-T400-T500-and-newer-T/T440s-speaker-noise/td-p/
1339883
As the noise comes from the analog loopback path, disabling the path
is the easy workaround.
Also, the machine gives significant cracking noises at PM suspend. A
workaround found by trial-and-error is to disable the shutup callback
currently used for ALC269-variant.
This patch addresses these noise issues by introducing a new fixup
chain. Although the same workaround might be applicable to other
Thinkpad models, it's applied only to T440s (17aa:220c) in this patch,
so far, just to be safe (you chicken!). As a compromise, a new model
option string "tp440" is provided now, though, so that owners of other
Thinkpad models can test it more easily.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=958504
Reported-and-tested-by: Tim Hardeck <thardeck@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nikolay Borisov [Mon, 7 Dec 2015 10:13:26 +0000 (12:13 +0200)]
netfilter: nfnetlink_queue: Unregister pernet subsys in case of init failure
Commit
3bfe049807c2403 ("netfilter: nfnetlink_{log,queue}:
Register pernet in first place") reorganised the initialisation
order of the pernet_subsys to avoid "use-before-initialised"
condition. However, in doing so the cleanup logic in nfnetlink_queue
got botched in that the pernet_subsys wasn't cleaned in case
nfnetlink_subsys_register failed. This patch adds the necessary
cleanup routine call.
Fixes: 3bfe049807c2403 ("netfilter: nfnetlink_{log,queue}: Register pernet in first place")
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jason A. Donenfeld [Sun, 6 Dec 2015 01:51:37 +0000 (02:51 +0100)]
crypto: skcipher - Copy iv from desc even for 0-len walks
Some ciphers actually support encrypting zero length plaintexts. For
example, many AEAD modes support this. The resulting ciphertext for
those winds up being only the authentication tag, which is a result of
the key, the iv, the additional data, and the fact that the plaintext
had zero length. The blkcipher constructors won't copy the IV to the
right place, however, when using a zero length input, resulting in
some significant problems when ciphers call their initialization
routines, only to find that the ->iv parameter is uninitialized. One
such example of this would be using chacha20poly1305 with a zero length
input, which then calls chacha20, which calls the key setup routine,
which eventually OOPSes due to the uninitialized ->iv member.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
H. Nikolaus Schaller [Fri, 13 Nov 2015 10:29:07 +0000 (11:29 +0100)]
OMAPDSS: fix timings for VENC to match what omapdrm expects
Otherwise check_timings fails and we get a "has no modes" message
from xrandr.
This fix makes the venc assume PAL and NTSC timings that match the
timings synthetized by copy_timings_drm_to_omap() from omapdrm
mode settings so that check_timings() succeeds.
Tested on: BeagleBoard XM, GTA04 and OpenPandora
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Wang Dongsheng [Thu, 3 Dec 2015 01:54:12 +0000 (09:54 +0800)]
video: fbdev: fsl: Fix kernel crash when diu_ops is not implemented
If diu_ops is not implemented on platform, kernel will access a NULL
pointer. We need to check this pointer in DIU initialization.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Oded Gabbay [Fri, 4 Dec 2015 21:09:05 +0000 (23:09 +0200)]
radeon: Fix VCE IB test on Big-Endian systems
This patch makes the VCE IB test pass on Big-Endian systems. It converts
to little-endian the contents of the VCE message.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oded Gabbay [Fri, 4 Dec 2015 21:09:04 +0000 (23:09 +0200)]
radeon: Fix VCE ring test for Big-Endian systems
This patch fixes the VCE ring test when running on Big-Endian machines.
Every write to the ring needs to be translated to little-endian.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oded Gabbay [Fri, 4 Dec 2015 21:09:03 +0000 (23:09 +0200)]
radeon/cik: Fix GFX IB test on Big-Endian
This patch makes the IB test on the GFX ring pass for CI-based cards
installed in Big-Endian machines.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chunming Zhou [Mon, 7 Dec 2015 07:02:52 +0000 (15:02 +0800)]
drm/amdgpu: fix the lost duplicates checking
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Cc: stable@vger.kernel.org
Dave Airlie [Wed, 9 Dec 2015 04:16:53 +0000 (14:16 +1000)]
Merge tag 'vmwgfx-fixes-4.4-151208' of git://people.freedesktop.org/~thomash/linux into drm-fixes
Pull request of 2015-12-08
A couple of fixes for vmwgfx. A WARN() fix by Dan Carpenter,
a TTM read/write lock imbalance causing occasional hangs with Wayland and
an implementation of cursor_set2 to fix incorrectly offset Wayland cursors.
* tag 'vmwgfx-fixes-4.4-151208' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Implement the cursor_set2 callback v2
drm/vmwgfx: fix a warning message
drm/ttm: Fixed a read/write lock imbalance
Dave Airlie [Wed, 9 Dec 2015 04:15:58 +0000 (14:15 +1000)]
Merge branch 'linux-4.4' of https://github.com/skeggsb/linux into drm-fixes
Just the one commit I mentioned earlier, making the PGOB workaround the
default.
* 'linux-4.4' of https://github.com/skeggsb/linux:
drm/nouveau/pmu: remove whitelist for PGOB-exit WAR, enable by default