static void __init at91rm9200_ioremap_registers(void)
{
at91rm9200_ioremap_st(AT91RM9200_BASE_ST);
+ at91_ioremap_ramc(0, AT91RM9200_BASE_MC, 256);
}
static void __init at91rm9200_initialize(void)
#include <mach/board.h>
#include <mach/at91rm9200.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
data->chipselect = 4; /* can only use EBI ChipSelect 4 */
/* CF takes over CS4, CS5, CS6 */
- csa = at91_sys_read(AT91_EBI_CSA);
- at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH);
+ csa = at91_ramc_read(0, AT91_EBI_CSA);
+ at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH);
/*
* Static memory controller timing adjustments.
* REVISIT: these timings are in terms of MCK cycles, so
* when MCK changes (cpufreq etc) so must these values...
*/
- at91_sys_write(AT91_SMC_CSR(4),
+ at91_ramc_write(0, AT91_SMC_CSR(4),
AT91_SMC_ACSS_STD
| AT91_SMC_DBW_16
| AT91_SMC_BAT
return;
/* enable the address range of CS3 */
- csa = at91_sys_read(AT91_EBI_CSA);
- at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
+ csa = at91_ramc_read(0, AT91_EBI_CSA);
+ at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
/* set the bus interface characteristics */
- at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
+ at91_ramc_write(0, AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
| AT91_SMC_NWS_(5)
| AT91_SMC_TDF_(1)
| AT91_SMC_RWSETUP_(0) /* tDS Data Set up Time 30 - ns */
{
at91_ioremap_shdwc(AT91SAM9260_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9260_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9260_BASE_SDRAMC, 512);
at91sam926x_ioremap_pit(AT91SAM9260_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC);
at91_ioremap_matrix(AT91SAM9260_BASE_MATRIX);
{
at91_ioremap_shdwc(AT91SAM9261_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9261_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9261_BASE_SDRAMC, 512);
at91sam926x_ioremap_pit(AT91SAM9261_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC);
at91_ioremap_matrix(AT91SAM9261_BASE_MATRIX);
{
at91_ioremap_shdwc(AT91SAM9263_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9263_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9263_BASE_SDRAMC0, 512);
+ at91_ioremap_ramc(1, AT91SAM9263_BASE_SDRAMC1, 512);
at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0);
at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
#include <linux/linkage.h>
#include <mach/hardware.h>
-#include <mach/at91sam9_sdramc.h>
+#include <mach/at91_ramc.h>
#include <mach/at91_rstc.h>
.arm
.globl at91sam9_alt_restart
-at91sam9_alt_restart: ldr r0, .at91_va_base_sdramc @ preload constants
- ldr r1, =at91_rstc_base
- ldr r1, [r1]
+at91sam9_alt_restart: ldr r0, =at91_ramc_base @ preload constants
+ ldr r0, [r0]
+ ldr r4, =at91_rstc_base
+ ldr r1, [r4]
mov r2, #1
mov r3, #AT91_SDRAMC_LPCB_POWER_DOWN
str r4, [r1, #AT91_RSTC_CR] @ reset processor
b .
-
-.at91_va_base_sdramc:
- .word AT91_VA_BASE_SYS + AT91_SDRAMC0
{
at91_ioremap_shdwc(AT91SAM9G45_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9G45_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9G45_BASE_DDRSDRC1, 512);
+ at91_ioremap_ramc(1, AT91SAM9G45_BASE_DDRSDRC0, 512);
at91sam926x_ioremap_pit(AT91SAM9G45_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9G45_BASE_SMC);
at91_ioremap_matrix(AT91SAM9G45_BASE_MATRIX);
#include <linux/linkage.h>
#include <mach/hardware.h>
-#include <mach/at91sam9_ddrsdr.h>
+#include <mach/at91_ramc.h>
#include <mach/at91_rstc.h>
.arm
.globl at91sam9g45_restart
at91sam9g45_restart:
- ldr r0, .at91_va_base_sdramc0 @ preload constants
- ldr r1, =at91_rstc_base
- ldr r1, [r1]
+ ldr r5, =at91_ramc_base @ preload constants
+ ldr r0, [r5]
+ ldr r4, =at91_rstc_base
+ ldr r1, [r4]
mov r2, #1
mov r3, #AT91_DDRSDRC_LPCB_POWER_DOWN
str r4, [r1, #AT91_RSTC_CR] @ reset processor
b .
-
-.at91_va_base_sdramc0:
- .word AT91_VA_BASE_SYS + AT91_DDRSDRC0
{
at91_ioremap_shdwc(AT91SAM9RL_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9RL_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9RL_BASE_SDRAMC, 512);
at91sam926x_ioremap_pit(AT91SAM9RL_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9RL_BASE_SMC);
at91_ioremap_matrix(AT91SAM9RL_BASE_MATRIX);
{
if (of_at91sam926x_pit_init() < 0)
panic("Impossible to find PIT\n");
+ at91_ioremap_ramc(0, AT91SAM9X5_BASE_DDRSDRC0, 512);
}
void __init at91sam9x5_initialize(void)
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include <mach/cpu.h>
#include "generic.h"
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include <mach/cpu.h>
#include "generic.h"
at91_add_device_mmc(0, &eco920_mmc_data);
platform_device_register(&eco920_flash);
- at91_sys_write(AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1)
+ at91_ramc_write(0, AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1)
| AT91_SMC_RWSETUP_(1)
| AT91_SMC_DBW_8
| AT91_SMC_WSEN
at91_set_deglitch(AT91_PIN_PA23, 1);
/* Initialization of the Static Memory Controller for Chip Select 3 */
- at91_sys_write(AT91_SMC_CSR(3),
+ at91_ramc_write(0, AT91_SMC_CSR(3),
AT91_SMC_DBW_16 | /* 16 bit */
AT91_SMC_WSEN |
AT91_SMC_NWS_(5) | /* wait states */
#include <mach/board.h>
#include <mach/cpu.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
#include <mach/hardware.h>
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
#include <mach/hardware.h>
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
#include <mach/hardware.h>
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include <mach/cpu.h>
#include "generic.h"
at91_set_A_periph(AT91_PIN_PC6, 0);
/* Initialization of the Static Memory Controller for Chip Select 2 */
- at91_sys_write(AT91_SMC_CSR(2), AT91_SMC_DBW_16 /* 16 bit */
+ at91_ramc_write(0, AT91_SMC_CSR(2), AT91_SMC_DBW_16 /* 16 bit */
| AT91_SMC_WSEN | AT91_SMC_NWS_(0x4) /* wait states */
| AT91_SMC_TDF_(0x100) /* float time */
);
/* Matrix */
extern void at91_ioremap_matrix(u32 base_addr);
+/* Ram Controler */
+extern void at91_ioremap_ramc(int id, u32 addr, u32 size);
+
/* GPIO */
#define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */
#define AT91RM9200_BGA 4 /* AT91RM9200 BGA package has 4 banks */
--- /dev/null
+/*
+ * Header file for the Atmel RAM Controller
+ *
+ * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2 only
+ */
+
+#ifndef __AT91_RAMC_H__
+#define __AT91_RAMC_H__
+
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_ramc_base[];
+
+#define at91_ramc_read(id, field) \
+ __raw_readl(at91_ramc_base[id] + field)
+
+#define at91_ramc_write(id, field, value) \
+ __raw_writel(value, at91_ramc_base[id] + field)
+#else
+.extern at91_ramc_base
+#endif
+
+#ifdef CONFIG_ARCH_AT91RM9200
+#include <mach/at91rm9200_mc.h>
+#else
+#include <mach/at91sam9_ddrsdr.h>
+#include <mach/at91sam9_sdramc.h>
+#endif
+
+#endif /* __AT91_RAMC_H__ */
* System Peripherals (offset from AT91_BASE_SYS)
*/
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) /* Power Management Controller */
-#define AT91_MC (0xffffff00 - AT91_BASE_SYS) /* Memory Controllers */
#define AT91RM9200_BASE_DBGU AT91_BASE_DBGU0 /* Debug Unit */
#define AT91RM9200_BASE_PIOA 0xfffff400 /* PIO Controller A */
#define AT91RM9200_BASE_PIOD 0xfffffa00 /* PIO Controller D */
#define AT91RM9200_BASE_ST 0xfffffd00 /* System Timer */
#define AT91RM9200_BASE_RTC 0xfffffe00 /* Real-Time Clock */
+#define AT91RM9200_BASE_MC 0xffffff00 /* Memory Controllers */
#define AT91_USART0 AT91RM9200_BASE_US0
#define AT91_USART1 AT91RM9200_BASE_US1
#define AT91RM9200_MC_H
/* Memory Controller */
-#define AT91_MC_RCR (AT91_MC + 0x00) /* MC Remap Control Register */
+#define AT91_MC_RCR 0x00 /* MC Remap Control Register */
#define AT91_MC_RCB (1 << 0) /* Remap Command Bit */
-#define AT91_MC_ASR (AT91_MC + 0x04) /* MC Abort Status Register */
+#define AT91_MC_ASR 0x04 /* MC Abort Status Register */
#define AT91_MC_UNADD (1 << 0) /* Undefined Address Abort Status */
#define AT91_MC_MISADD (1 << 1) /* Misaligned Address Abort Status */
#define AT91_MC_ABTSZ (3 << 8) /* Abort Size Status */
#define AT91_MC_SVMST2 (1 << 26) /* Saved UHP Abort Source */
#define AT91_MC_SVMST3 (1 << 27) /* Saved EMAC Abort Source */
-#define AT91_MC_AASR (AT91_MC + 0x08) /* MC Abort Address Status Register */
+#define AT91_MC_AASR 0x08 /* MC Abort Address Status Register */
-#define AT91_MC_MPR (AT91_MC + 0x0c) /* MC Master Priority Register */
+#define AT91_MC_MPR 0x0c /* MC Master Priority Register */
#define AT91_MPR_MSTP0 (7 << 0) /* ARM920T Priority */
#define AT91_MPR_MSTP1 (7 << 4) /* PDC Priority */
#define AT91_MPR_MSTP2 (7 << 8) /* UHP Priority */
#define AT91_MPR_MSTP3 (7 << 12) /* EMAC Priority */
/* External Bus Interface (EBI) registers */
-#define AT91_EBI_CSA (AT91_MC + 0x60) /* Chip Select Assignment Register */
+#define AT91_EBI_CSA 0x60 /* Chip Select Assignment Register */
#define AT91_EBI_CS0A (1 << 0) /* Chip Select 0 Assignment */
#define AT91_EBI_CS0A_SMC (0 << 0)
#define AT91_EBI_CS0A_BFC (1 << 0)
#define AT91_EBI_DBPUC (1 << 0) /* Data Bus Pull-Up Configuration */
/* Static Memory Controller (SMC) registers */
-#define AT91_SMC_CSR(n) (AT91_MC + 0x70 + ((n) * 4))/* SMC Chip Select Register */
+#define AT91_SMC_CSR(n) (0x70 + ((n) * 4)) /* SMC Chip Select Register */
#define AT91_SMC_NWS (0x7f << 0) /* Number of Wait States */
#define AT91_SMC_NWS_(x) ((x) << 0)
#define AT91_SMC_WSEN (1 << 7) /* Wait State Enable */
#define AT91_SMC_RWHOLD_(x) ((x) << 28)
/* Burst Flash Controller register */
-#define AT91_BFC_MR (AT91_MC + 0xc0) /* Mode Register */
+#define AT91_BFC_MR 0xc0 /* Mode Register */
#define AT91_BFC_BFCOM (3 << 0) /* Burst Flash Controller Operating Mode */
#define AT91_BFC_BFCOM_DISABLED (0 << 0)
#define AT91_BFC_BFCOM_ASYNC (1 << 0)
#define AT91RM9200_SDRAMC_H
/* SDRAM Controller registers */
-#define AT91RM9200_SDRAMC_MR (AT91_MC + 0x90) /* Mode Register */
+#define AT91RM9200_SDRAMC_MR 0x90 /* Mode Register */
#define AT91RM9200_SDRAMC_MODE (0xf << 0) /* Command Mode */
#define AT91RM9200_SDRAMC_MODE_NORMAL (0 << 0)
#define AT91RM9200_SDRAMC_MODE_NOP (1 << 0)
#define AT91RM9200_SDRAMC_DBW_32 (0 << 4)
#define AT91RM9200_SDRAMC_DBW_16 (1 << 4)
-#define AT91RM9200_SDRAMC_TR (AT91_MC + 0x94) /* Refresh Timer Register */
+#define AT91RM9200_SDRAMC_TR 0x94 /* Refresh Timer Register */
#define AT91RM9200_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */
-#define AT91RM9200_SDRAMC_CR (AT91_MC + 0x98) /* Configuration Register */
+#define AT91RM9200_SDRAMC_CR 0x98 /* Configuration Register */
#define AT91RM9200_SDRAMC_NC (3 << 0) /* Number of Column Bits */
#define AT91RM9200_SDRAMC_NC_8 (0 << 0)
#define AT91RM9200_SDRAMC_NC_9 (1 << 0)
#define AT91RM9200_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */
#define AT91RM9200_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */
-#define AT91RM9200_SDRAMC_SRR (AT91_MC + 0x9c) /* Self Refresh Register */
-#define AT91RM9200_SDRAMC_LPR (AT91_MC + 0xa0) /* Low Power Register */
-#define AT91RM9200_SDRAMC_IER (AT91_MC + 0xa4) /* Interrupt Enable Register */
-#define AT91RM9200_SDRAMC_IDR (AT91_MC + 0xa8) /* Interrupt Disable Register */
-#define AT91RM9200_SDRAMC_IMR (AT91_MC + 0xac) /* Interrupt Mask Register */
-#define AT91RM9200_SDRAMC_ISR (AT91_MC + 0xb0) /* Interrupt Status Register */
+#define AT91RM9200_SDRAMC_SRR 0x9c /* Self Refresh Register */
+#define AT91RM9200_SDRAMC_LPR 0xa0 /* Low Power Register */
+#define AT91RM9200_SDRAMC_IER 0xa4 /* Interrupt Enable Register */
+#define AT91RM9200_SDRAMC_IDR 0xa8 /* Interrupt Disable Register */
+#define AT91RM9200_SDRAMC_IMR 0xac /* Interrupt Mask Register */
+#define AT91RM9200_SDRAMC_ISR 0xb0 /* Interrupt Status Register */
#endif
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
#define AT91SAM9260_BASE_ECC 0xffffe800
+#define AT91SAM9260_BASE_SDRAMC 0xffffea00
#define AT91SAM9260_BASE_SMC 0xffffec00
#define AT91SAM9260_BASE_MATRIX 0xffffee00
#define AT91SAM9260_BASE_DBGU AT91_BASE_DBGU0
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
#define AT91SAM9261_BASE_SMC 0xffffec00
#define AT91SAM9261_BASE_MATRIX 0xffffee00
+#define AT91SAM9261_BASE_SDRAMC 0xffffea00
#define AT91SAM9261_BASE_DBGU AT91_BASE_DBGU0
#define AT91SAM9261_BASE_PIOA 0xfffff400
#define AT91SAM9261_BASE_PIOB 0xfffff600
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_SDRAMC0 (0xffffe200 - AT91_BASE_SYS)
-#define AT91_SDRAMC1 (0xffffe800 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
#define AT91SAM9263_BASE_ECC0 0xffffe000
+#define AT91SAM9263_BASE_SDRAMC0 0xffffe200
#define AT91SAM9263_BASE_SMC0 0xffffe400
#define AT91SAM9263_BASE_ECC1 0xffffe600
+#define AT91SAM9263_BASE_SDRAMC1 0xffffe800
#define AT91SAM9263_BASE_SMC1 0xffffea00
#define AT91SAM9263_BASE_MATRIX 0xffffec00
#define AT91SAM9263_BASE_DBGU AT91_BASE_DBGU1
#define AT91_DDRSDRC_WPVS (1 << 0) /* Write protect violation status */
#define AT91_DDRSDRC_WPVSRC (0xffff << 8) /* Write protect violation source */
-/* Register access macros */
-#define at91_ramc_read(num, reg) \
- at91_sys_read(AT91_DDRSDRC##num + reg)
-#define at91_ramc_write(num, reg, value) \
- at91_sys_write(AT91_DDRSDRC##num + reg, value)
-
#endif
#define AT91_SDRAMC_MD_SDRAM 0
#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1
-/* Register access macros */
-#define at91_ramc_read(num, reg) \
- at91_sys_read(AT91_SDRAMC##num + reg)
-#define at91_ramc_write(num, reg, value) \
- at91_sys_write(AT91_SDRAMC##num + reg, value)
-
#endif
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_DDRSDRC1 (0xffffe400 - AT91_BASE_SYS)
-#define AT91_DDRSDRC0 (0xffffe600 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
#define AT91SAM9G45_BASE_ECC 0xffffe200
+#define AT91SAM9G45_BASE_DDRSDRC1 0xffffe400
+#define AT91SAM9G45_BASE_DDRSDRC0 0xffffe600
#define AT91SAM9G45_BASE_DMA 0xffffec00
#define AT91SAM9G45_BASE_SMC 0xffffe800
#define AT91SAM9G45_BASE_MATRIX 0xffffea00
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_SCKCR (0xfffffd50 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
#define AT91SAM9RL_BASE_DMA 0xffffe600
#define AT91SAM9RL_BASE_ECC 0xffffe800
+#define AT91SAM9RL_BASE_SDRAMC 0xffffea00
#define AT91SAM9RL_BASE_SMC 0xffffec00
#define AT91SAM9RL_BASE_MATRIX 0xffffee00
#define AT91SAM9RL_BASE_DBGU AT91_BASE_DBGU0
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_DDRSDRC0 (0xffffe800 - AT91_BASE_SYS)
+#define AT91SAM9X5_BASE_DDRSDRC0 0xffffe800
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
/*
#endif
static void __iomem *at91_pmc_base = (void __iomem*)(AT91_VA_BASE_SYS + AT91_PMC);
-#ifdef CONFIG_ARCH_AT91RM9200
-static void __iomem *at91_ramc0_base = (void __iomem*)AT91_VA_BASE_SYS;
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
-static void __iomem *at91_ramc0_base = (void __iomem*)(AT91_VA_BASE_SYS + AT91_DDRSDRC0);
-#else
-static void __iomem *at91_ramc0_base = (void __iomem*)(AT91_VA_BASE_SYS + AT91_SDRAMC0);
-#endif
+void __iomem *at91_ramc_base[2];
-#if defined(CONFIG_ARCH_AT91SAM9G45)
-static void __iomem *at91_ramc1_base = (void __iomem*)(AT91_VA_BASE_SYS + AT91_DDRSDRC1);
-#else
-static void __iomem *at91_ramc1_base = NULL;
-#endif
+void __init at91_ioremap_ramc(int id, u32 addr, u32 size)
+{
+ if (id < 0 || id > 1) {
+ pr_emerg("Wrong RAM controller id (%d), cannot continue\n", id);
+ BUG();
+ }
+ at91_ramc_base[id] = ioremap(addr, size);
+ if (!at91_ramc_base[id])
+ panic("Impossible to ioremap ramc.%d 0x%x\n", id, addr);
+}
static int at91_pm_enter(suspend_state_t state)
{
/* copy slow_clock handler to SRAM, and call it */
memcpy(slow_clock, at91_slow_clock, at91_slow_clock_sz);
#endif
- slow_clock(at91_pmc_base, at91_ramc0_base, at91_ramc1_base);
+ slow_clock(at91_pmc_base, at91_ramc_base[0], at91_ramc_base[1]);
break;
} else {
pr_info("AT91: PM - no slow clock mode enabled ...\n");
#ifdef CONFIG_ARCH_AT91RM9200
/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
- at91_sys_write(AT91RM9200_SDRAMC_LPR, 0);
+ at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
#endif
suspend_set_ops(&at91_pm_ops);
#ifndef __ARCH_ARM_MACH_AT91_PM
#define __ARCH_ARM_MACH_AT91_PM
+#include <mach/at91_ramc.h>
#ifdef CONFIG_ARCH_AT91RM9200
-#include <mach/at91rm9200_mc.h>
#include <mach/at91rm9200_sdramc.h>
/*
static inline void at91rm9200_standby(void)
{
- u32 lpr = at91_sys_read(AT91RM9200_SDRAMC_LPR);
+ u32 lpr = at91_ramc_read(0, AT91RM9200_SDRAMC_LPR);
asm volatile(
"b 1f\n\t"
#define at91_standby at91rm9200_standby
#elif defined(CONFIG_ARCH_AT91SAM9G45)
-#include <mach/at91sam9_ddrsdr.h>
/* We manage both DDRAM/SDRAM controllers, we need more than one value to
* remember.
#define at91_standby at91sam9g45_standby
#else
-#include <mach/at91sam9_sdramc.h>
#ifdef CONFIG_ARCH_AT91SAM9263
/*
#include <linux/linkage.h>
#include <mach/hardware.h>
#include <mach/at91_pmc.h>
-
-#if defined(CONFIG_ARCH_AT91RM9200)
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91rm9200_sdramc.h>
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
-#include <mach/at91sam9_ddrsdr.h>
-#else
-#include <mach/at91sam9_sdramc.h>
-#endif
+#include <mach/at91_ramc.h>
#ifdef CONFIG_ARCH_AT91SAM9263
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
/*
/*
* Use 16 bit accesses unless/until we need 8-bit i/o space.
*/
- csr = at91_sys_read(AT91_SMC_CSR(cf->board->chipselect)) & ~AT91_SMC_DBW;
+ csr = at91_ramc_read(0, AT91_SMC_CSR(cf->board->chipselect)) & ~AT91_SMC_DBW;
/*
* NOTE: this CF controller ignores IOIS16, so we can't really do
csr |= AT91_SMC_DBW_16;
pr_debug("%s: 16bit i/o bus\n", driver_name);
}
- at91_sys_write(AT91_SMC_CSR(cf->board->chipselect), csr);
+ at91_ramc_write(0, AT91_SMC_CSR(cf->board->chipselect), csr);
io->start = cf->socket.io_offset;
io->stop = io->start + SZ_2K - 1;
projects / firefly-linux-kernel-4.4.55.git / commitdiff