[PATCH] I2O: new sysfs attributes and Adaptec specific block device access and 64...
authorMarkus Lidel <Markus.Lidel@shadowconnect.com>
Fri, 24 Jun 2005 05:02:16 +0000 (22:02 -0700)
committerLinus Torvalds <torvalds@ppc970.osdl.org>
Fri, 24 Jun 2005 07:05:28 +0000 (00:05 -0700)
Changes:
 - Added Bus-OSM which could be used by user space programs to reset a
   channel on the controller
 - Make ioctl's in Config-OSM obsolete in prefer for sysfs attributes and
   move those to its own file
 - Added sysfs attribute for firmware read and write access for I2O
   controllers
 - Added special handling of firmware read and write access for Adaptec
   controllers
 - Added vendor id and product id as sysfs-attribute to Executive classes
 - Added automatic notification of LCT change handling to Exec-OSM
 - Added flushing function to Block-OSM for later barrier implementation
 - Use PRIVATE messages for Block access on Adaptec controllers, which are
   faster then BLOCK class access
 - Cleaned up support for Promise controller
 - New messages are now detected using the IRQ status register as
   suggested by the I2O spec
 - Added i2o_dma_high() and i2o_dma_low() functions
 - Added facility for SG tablesize calculation when using 32-bit and
   64-bit DMA addresses
 - Added i2o_dma_map_single() and i2o_dma_map_sg() which could build the
   SG list for 32-bit as well as 64-bit DMA addresses

Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
15 files changed:
drivers/message/i2o/Kconfig
drivers/message/i2o/Makefile
drivers/message/i2o/bus-osm.c [new file with mode: 0644]
drivers/message/i2o/config-osm.c [new file with mode: 0644]
drivers/message/i2o/driver.c
drivers/message/i2o/exec-osm.c
drivers/message/i2o/i2o_block.c
drivers/message/i2o/i2o_block.h
drivers/message/i2o/i2o_config.c
drivers/message/i2o/i2o_proc.c
drivers/message/i2o/i2o_scsi.c
drivers/message/i2o/iop.c
drivers/message/i2o/pci.c
include/linux/i2o-dev.h
include/linux/i2o.h

index 8d132b0d6b1218d3dfc2360d54e4c631675e28e3..ce278e060aca692d6fd1f45a68413474457587a5 100644 (file)
@@ -35,6 +35,24 @@ config I2O_CONFIG
          To compile this support as a module, choose M here: the
          module will be called i2o_config.
 
+config I2O_CONFIG_OLD_IOCTL
+       bool "Enable ioctls (OBSOLETE)"
+       depends on I2O_CONFIG
+       default y
+       ---help---
+         Enables old ioctls.
+
+config I2O_BUS
+       tristate "I2O Bus Adapter OSM"
+       depends on I2O
+       ---help---
+         Include support for the I2O Bus Adapter OSM. The Bus Adapter OSM
+         provides access to the busses on the I2O controller. The main purpose
+         is to rescan the bus to find new devices.
+
+         To compile this support as a module, choose M here: the
+         module will be called i2o_bus.
+
 config I2O_BLOCK
        tristate "I2O Block OSM"
        depends on I2O
index aabc6cdc3fcec4025a9dfd0b19dd58731dcf232e..2c2e39aa1efaf04d8747018369089bc44a0c3b8a 100644 (file)
@@ -6,8 +6,11 @@
 #
 
 i2o_core-y             += iop.o driver.o device.o debug.o pci.o exec-osm.o
+i2o_bus-y              += bus-osm.o
+i2o_config-y           += config-osm.o
 obj-$(CONFIG_I2O)      += i2o_core.o
 obj-$(CONFIG_I2O_CONFIG)+= i2o_config.o
+obj-$(CONFIG_I2O_BUS)  += i2o_bus.o
 obj-$(CONFIG_I2O_BLOCK)        += i2o_block.o
 obj-$(CONFIG_I2O_SCSI) += i2o_scsi.o
 obj-$(CONFIG_I2O_PROC) += i2o_proc.o
diff --git a/drivers/message/i2o/bus-osm.c b/drivers/message/i2o/bus-osm.c
new file mode 100644 (file)
index 0000000..d43c358
--- /dev/null
@@ -0,0 +1,164 @@
+/*
+ *     Bus Adapter OSM
+ *
+ *     Copyright (C) 2005      Markus Lidel <Markus.Lidel@shadowconnect.com>
+ *
+ *     This program is free software; you can redistribute it and/or modify it
+ *     under the terms of the GNU General Public License as published by the
+ *     Free Software Foundation; either version 2 of the License, or (at your
+ *     option) any later version.
+ *
+ *     Fixes/additions:
+ *             Markus Lidel <Markus.Lidel@shadowconnect.com>
+ *                     initial version.
+ */
+
+#include <linux/module.h>
+#include <linux/i2o.h>
+
+#define OSM_NAME       "bus-osm"
+#define OSM_VERSION    "$Rev$"
+#define OSM_DESCRIPTION        "I2O Bus Adapter OSM"
+
+static struct i2o_driver i2o_bus_driver;
+
+/* Bus OSM class handling definition */
+static struct i2o_class_id i2o_bus_class_id[] = {
+       {I2O_CLASS_BUS_ADAPTER},
+       {I2O_CLASS_END}
+};
+
+/**
+ *     i2o_bus_scan - Scan the bus for new devices
+ *     @dev: I2O device of the bus, which should be scanned
+ *
+ *     Scans the bus dev for new / removed devices. After the scan a new LCT
+ *     will be fetched automatically.
+ *
+ *     Returns 0 on success or negative error code on failure.
+ */
+static int i2o_bus_scan(struct i2o_device *dev)
+{
+       struct i2o_message __iomem *msg;
+       u32 m;
+
+       m = i2o_msg_get_wait(dev->iop, &msg, I2O_TIMEOUT_MESSAGE_GET);
+       if (m == I2O_QUEUE_EMPTY)
+               return -ETIMEDOUT;
+
+       writel(FIVE_WORD_MSG_SIZE | SGL_OFFSET_0, &msg->u.head[0]);
+       writel(I2O_CMD_BUS_SCAN << 24 | HOST_TID << 12 | dev->lct_data.tid,
+              &msg->u.head[1]);
+
+       return i2o_msg_post_wait(dev->iop, m, 60);
+};
+
+/**
+ *     i2o_bus_store_scan - Scan the I2O Bus Adapter
+ *     @d: device which should be scanned
+ *
+ *     Returns count.
+ */
+static ssize_t i2o_bus_store_scan(struct device *d, const char *buf,
+                                 size_t count)
+{
+       struct i2o_device *i2o_dev = to_i2o_device(d);
+       int rc;
+
+       if ((rc = i2o_bus_scan(i2o_dev)))
+               osm_warn("bus scan failed %d\n", rc);
+
+       return count;
+}
+
+/* Bus Adapter OSM device attributes */
+static DEVICE_ATTR(scan, S_IWUSR, NULL, i2o_bus_store_scan);
+
+/**
+ *     i2o_bus_probe - verify if dev is a I2O Bus Adapter device and install it
+ *     @dev: device to verify if it is a I2O Bus Adapter device
+ *
+ *     Because we want all Bus Adapters always return 0.
+ *
+ *     Returns 0.
+ */
+static int i2o_bus_probe(struct device *dev)
+{
+       struct i2o_device *i2o_dev = to_i2o_device(get_device(dev));
+
+       device_create_file(dev, &dev_attr_scan);
+
+       osm_info("device added (TID: %03x)\n", i2o_dev->lct_data.tid);
+
+       return 0;
+};
+
+/**
+ *     i2o_bus_remove - remove the I2O Bus Adapter device from the system again
+ *     @dev: I2O Bus Adapter device which should be removed
+ *
+ *     Always returns 0.
+ */
+static int i2o_bus_remove(struct device *dev)
+{
+       struct i2o_device *i2o_dev = to_i2o_device(dev);
+
+       device_remove_file(dev, &dev_attr_scan);
+
+       put_device(dev);
+
+       osm_info("device removed (TID: %03x)\n", i2o_dev->lct_data.tid);
+
+       return 0;
+};
+
+/* Bus Adapter OSM driver struct */
+static struct i2o_driver i2o_bus_driver = {
+       .name = OSM_NAME,
+       .classes = i2o_bus_class_id,
+       .driver = {
+                  .probe = i2o_bus_probe,
+                  .remove = i2o_bus_remove,
+                  },
+};
+
+/**
+ *     i2o_bus_init - Bus Adapter OSM initialization function
+ *
+ *     Only register the Bus Adapter OSM in the I2O core.
+ *
+ *     Returns 0 on success or negative error code on failure.
+ */
+static int __init i2o_bus_init(void)
+{
+       int rc;
+
+       printk(KERN_INFO OSM_DESCRIPTION " v" OSM_VERSION "\n");
+
+       /* Register Bus Adapter OSM into I2O core */
+       rc = i2o_driver_register(&i2o_bus_driver);
+       if (rc) {
+               osm_err("Could not register Bus Adapter OSM\n");
+               return rc;
+       }
+
+       return 0;
+};
+
+/**
+ *     i2o_bus_exit - Bus Adapter OSM exit function
+ *
+ *     Unregisters Bus Adapter OSM from I2O core.
+ */
+static void __exit i2o_bus_exit(void)
+{
+       i2o_driver_unregister(&i2o_bus_driver);
+};
+
+MODULE_AUTHOR("Markus Lidel <Markus.Lidel@shadowconnect.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION(OSM_DESCRIPTION);
+MODULE_VERSION(OSM_VERSION);
+
+module_init(i2o_bus_init);
+module_exit(i2o_bus_exit);
diff --git a/drivers/message/i2o/config-osm.c b/drivers/message/i2o/config-osm.c
new file mode 100644 (file)
index 0000000..d026760
--- /dev/null
@@ -0,0 +1,579 @@
+/*
+ *     Configuration OSM
+ *
+ *     Copyright (C) 2005      Markus Lidel <Markus.Lidel@shadowconnect.com>
+ *
+ *     This program is free software; you can redistribute it and/or modify it
+ *     under the terms of the GNU General Public License as published by the
+ *     Free Software Foundation; either version 2 of the License, or (at your
+ *     option) any later version.
+ *
+ *     Fixes/additions:
+ *             Markus Lidel <Markus.Lidel@shadowconnect.com>
+ *                     initial version.
+ */
+
+#include <linux/module.h>
+#include <linux/i2o.h>
+#include <linux/namei.h>
+
+#include <asm/uaccess.h>
+
+#define OSM_NAME       "config-osm"
+#define OSM_VERSION    "1.248"
+#define OSM_DESCRIPTION        "I2O Configuration OSM"
+
+/* access mode user rw */
+#define S_IWRSR (S_IRUSR | S_IWUSR)
+
+static struct i2o_driver i2o_config_driver;
+
+/* Special file operations for sysfs */
+struct fops_attribute {
+       struct bin_attribute bin;
+       struct file_operations fops;
+};
+
+/**
+ *     sysfs_read_dummy
+ */
+static ssize_t sysfs_read_dummy(struct kobject *kobj, char *buf, loff_t offset,
+                               size_t count)
+{
+       return 0;
+};
+
+/**
+ *     sysfs_write_dummy
+ */
+static ssize_t sysfs_write_dummy(struct kobject *kobj, char *buf, loff_t offset,
+                                size_t count)
+{
+       return 0;
+};
+
+/**
+ *     sysfs_create_fops_file - Creates attribute with special file operations
+ *     @kobj: kobject which should contains the attribute
+ *     @attr: attributes which should be used to create file
+ *
+ *     First creates attribute @attr in kobject @kobj. If it is the first time
+ *     this function is called, merge old fops from sysfs with new one and
+ *     write it back. Afterwords the new fops will be set for the created
+ *     attribute.
+ *
+ *     Returns 0 on success or negative error code on failure.
+ */
+static int sysfs_create_fops_file(struct kobject *kobj,
+                                 struct fops_attribute *attr)
+{
+       struct file_operations tmp, *fops;
+       struct dentry *d;
+       struct qstr qstr;
+       int rc;
+
+       fops = &attr->fops;
+
+       if (fops->read)
+               attr->bin.read = sysfs_read_dummy;
+
+       if (fops->write)
+               attr->bin.write = sysfs_write_dummy;
+
+       if ((rc = sysfs_create_bin_file(kobj, &attr->bin)))
+               return rc;
+
+       qstr.name = attr->bin.attr.name;
+       qstr.len = strlen(qstr.name);
+       qstr.hash = full_name_hash(qstr.name, qstr.len);
+
+       if ((d = lookup_hash(&qstr, kobj->dentry))) {
+               if (!fops->owner) {
+                       memcpy(&tmp, d->d_inode->i_fop, sizeof(tmp));
+                       if (fops->read)
+                               tmp.read = fops->read;
+                       if (fops->write)
+                               tmp.write = fops->write;
+                       memcpy(fops, &tmp, sizeof(tmp));
+               }
+
+               d->d_inode->i_fop = fops;
+       } else
+               sysfs_remove_bin_file(kobj, &attr->bin);
+
+       return -ENOENT;
+};
+
+/**
+ *     sysfs_remove_fops_file - Remove attribute with special file operations
+ *     @kobj: kobject which contains the attribute
+ *     @attr: attributes which are used to create file
+ *
+ *     Only wrapper arround sysfs_remove_bin_file()
+ *
+ *     Returns 0 on success or negative error code on failure.
+ */
+static inline int sysfs_remove_fops_file(struct kobject *kobj,
+                                        struct fops_attribute *attr)
+{
+       return sysfs_remove_bin_file(kobj, &attr->bin);
+};
+
+/**
+ *     i2o_config_read_hrt - Returns the HRT of the controller
+ *     @kob: kernel object handle
+ *     @buf: buffer into which the HRT should be copied
+ *     @off: file offset
+ *     @count: number of bytes to read
+ *
+ *     Put @count bytes starting at @off into @buf from the HRT of the I2O
+ *     controller corresponding to @kobj.
+ *
+ *     Returns number of bytes copied into buffer.
+ */
+static ssize_t i2o_config_read_hrt(struct kobject *kobj, char *buf,
+                                  loff_t offset, size_t count)
+{
+       struct i2o_controller *c = kobj_to_i2o_device(kobj)->iop;
+       i2o_hrt *hrt = c->hrt.virt;
+
+       u32 size = (hrt->num_entries * hrt->entry_len + 2) * 4;
+
+       if (offset > size)
+               return 0;
+
+       if (offset + count > size)
+               count = size - offset;
+
+       memcpy(buf, (u8 *) hrt + offset, count);
+
+       return count;
+};
+
+/**
+ *     i2o_config_read_lct - Returns the LCT of the controller
+ *     @kob: kernel object handle
+ *     @buf: buffer into which the LCT should be copied
+ *     @off: file offset
+ *     @count: number of bytes to read
+ *
+ *     Put @count bytes starting at @off into @buf from the LCT of the I2O
+ *     controller corresponding to @kobj.
+ *
+ *     Returns number of bytes copied into buffer.
+ */
+static ssize_t i2o_config_read_lct(struct kobject *kobj, char *buf,
+                                  loff_t offset, size_t count)
+{
+       struct i2o_controller *c = kobj_to_i2o_device(kobj)->iop;
+       u32 size = c->lct->table_size * 4;
+
+       if (offset > size)
+               return 0;
+
+       if (offset + count > size)
+               count = size - offset;
+
+       memcpy(buf, (u8 *) c->lct + offset, count);
+
+       return count;
+};
+
+#define I2O_CONFIG_SW_ATTR(_name,_mode,_type,_swid) \
+static ssize_t i2o_config_##_name##_read(struct file *file, char __user *buf, size_t count, loff_t * offset) { \
+       return i2o_config_sw_read(file, buf, count, offset, _type, _swid); \
+};\
+\
+static ssize_t i2o_config_##_name##_write(struct file *file, const char __user *buf, size_t count, loff_t * offset) { \
+       return i2o_config_sw_write(file, buf, count, offset, _type, _swid); \
+}; \
+\
+static struct fops_attribute i2o_config_attr_##_name = { \
+       .bin = { .attr = { .name = __stringify(_name), .mode = _mode, \
+                          .owner = THIS_MODULE }, \
+                .size = 0, }, \
+       .fops = { .write = i2o_config_##_name##_write, \
+                 .read = i2o_config_##_name##_read} \
+};
+
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+
+/**
+ *     i2o_config_dpt_reagion - Converts type and id to flash region
+ *     @swtype: type of software module reading
+ *     @swid: id of software which should be read
+ *
+ *     Converts type and id from I2O spec to the matching region for DPT /
+ *     Adaptec controllers.
+ *
+ *     Returns region which match type and id or -1 on error.
+ */
+static u32 i2o_config_dpt_region(u8 swtype, u8 swid)
+{
+       switch (swtype) {
+       case I2O_SOFTWARE_MODULE_IRTOS:
+               /*
+                * content: operation firmware
+                * region size:
+                *      0xbc000 for 2554, 3754, 2564, 3757
+                *      0x170000 for 2865
+                *      0x17c000 for 3966
+                */
+               if (!swid)
+                       return 0;
+
+               break;
+
+       case I2O_SOFTWARE_MODULE_IOP_PRIVATE:
+               /*
+                * content: BIOS and SMOR
+                * BIOS size: first 0x8000 bytes
+                * region size:
+                *      0x40000 for 2554, 3754, 2564, 3757
+                *      0x80000 for 2865, 3966
+                */
+               if (!swid)
+                       return 1;
+
+               break;
+
+       case I2O_SOFTWARE_MODULE_IOP_CONFIG:
+               switch (swid) {
+               case 0:
+                       /*
+                        * content: NVRAM defaults
+                        * region size: 0x2000 bytes
+                        */
+                       return 2;
+               case 1:
+                       /*
+                        * content: serial number
+                        * region size: 0x2000 bytes
+                        */
+                       return 3;
+               }
+               break;
+       }
+
+       return -1;
+};
+
+#endif
+
+/**
+ *     i2o_config_sw_read - Read a software module from controller
+ *     @file: file pointer
+ *     @buf: buffer into which the data should be copied
+ *     @count: number of bytes to read
+ *     @off: file offset
+ *     @swtype: type of software module reading
+ *     @swid: id of software which should be read
+ *
+ *     Transfers @count bytes at offset @offset from IOP into buffer using
+ *     type @swtype and id @swid as described in I2O spec.
+ *
+ *     Returns number of bytes copied into buffer or error code on failure.
+ */
+static ssize_t i2o_config_sw_read(struct file *file, char __user * buf,
+                                 size_t count, loff_t * offset, u8 swtype,
+                                 u32 swid)
+{
+       struct sysfs_dirent *sd = file->f_dentry->d_parent->d_fsdata;
+       struct kobject *kobj = sd->s_element;
+       struct i2o_controller *c = kobj_to_i2o_device(kobj)->iop;
+       u32 m, function = I2O_CMD_SW_UPLOAD;
+       struct i2o_dma buffer;
+       struct i2o_message __iomem *msg;
+       u32 __iomem *mptr;
+       int rc, status;
+
+       m = i2o_msg_get_wait(c, &msg, I2O_TIMEOUT_MESSAGE_GET);
+       if (m == I2O_QUEUE_EMPTY)
+               return -EBUSY;
+
+       mptr = &msg->body[3];
+
+       if ((rc = i2o_dma_alloc(&c->pdev->dev, &buffer, count, GFP_KERNEL))) {
+               i2o_msg_nop(c, m);
+               return rc;
+       }
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+       if (c->adaptec) {
+               mptr = &msg->body[4];
+               function = I2O_CMD_PRIVATE;
+
+               writel(TEN_WORD_MSG_SIZE | SGL_OFFSET_8, &msg->u.head[0]);
+
+               writel(I2O_VENDOR_DPT << 16 | I2O_DPT_FLASH_READ,
+                      &msg->body[0]);
+               writel(i2o_config_dpt_region(swtype, swid), &msg->body[1]);
+               writel(*offset, &msg->body[2]);
+               writel(count, &msg->body[3]);
+       } else
+#endif
+               writel(NINE_WORD_MSG_SIZE | SGL_OFFSET_7, &msg->u.head[0]);
+
+       writel(0xD0000000 | count, mptr++);
+       writel(buffer.phys, mptr);
+
+       writel(function << 24 | HOST_TID << 12 | ADAPTER_TID, &msg->u.head[1]);
+       writel(i2o_config_driver.context, &msg->u.head[2]);
+       writel(0, &msg->u.head[3]);
+
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+       if (!c->adaptec)
+#endif
+       {
+               writel((u32) swtype << 16 | (u32) 1 << 8, &msg->body[0]);
+               writel(0, &msg->body[1]);
+               writel(swid, &msg->body[2]);
+       }
+
+       status = i2o_msg_post_wait_mem(c, m, 60, &buffer);
+
+       if (status == I2O_POST_WAIT_OK) {
+               if (!(rc = copy_to_user(buf, buffer.virt, count))) {
+                       rc = count;
+                       *offset += count;
+               }
+       } else
+               rc = -EIO;
+
+       if (status != -ETIMEDOUT)
+               i2o_dma_free(&c->pdev->dev, &buffer);
+
+       return rc;
+};
+
+/**
+ *     i2o_config_sw_write - Write a software module to controller
+ *     @file: file pointer
+ *     @buf: buffer into which the data should be copied
+ *     @count: number of bytes to read
+ *     @off: file offset
+ *     @swtype: type of software module writing
+ *     @swid: id of software which should be written
+ *
+ *     Transfers @count bytes at offset @offset from buffer to IOP using
+ *     type @swtype and id @swid as described in I2O spec.
+ *
+ *     Returns number of bytes copied from buffer or error code on failure.
+ */
+static ssize_t i2o_config_sw_write(struct file *file, const char __user * buf,
+                                  size_t count, loff_t * offset, u8 swtype,
+                                  u32 swid)
+{
+       struct sysfs_dirent *sd = file->f_dentry->d_parent->d_fsdata;
+       struct kobject *kobj = sd->s_element;
+       struct i2o_controller *c = kobj_to_i2o_device(kobj)->iop;
+       u32 m, function = I2O_CMD_SW_DOWNLOAD;
+       struct i2o_dma buffer;
+       struct i2o_message __iomem *msg;
+       u32 __iomem *mptr;
+       int rc, status;
+
+       m = i2o_msg_get_wait(c, &msg, I2O_TIMEOUT_MESSAGE_GET);
+       if (m == I2O_QUEUE_EMPTY)
+               return -EBUSY;
+
+       mptr = &msg->body[3];
+
+       if ((rc = i2o_dma_alloc(&c->pdev->dev, &buffer, count, GFP_KERNEL)))
+               goto nop_msg;
+
+       if ((rc = copy_from_user(buffer.virt, buf, count)))
+               goto free_buffer;
+
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+       if (c->adaptec) {
+               mptr = &msg->body[4];
+               function = I2O_CMD_PRIVATE;
+
+               writel(TEN_WORD_MSG_SIZE | SGL_OFFSET_8, &msg->u.head[0]);
+
+               writel(I2O_VENDOR_DPT << 16 | I2O_DPT_FLASH_WRITE,
+                      &msg->body[0]);
+               writel(i2o_config_dpt_region(swtype, swid), &msg->body[1]);
+               writel(*offset, &msg->body[2]);
+               writel(count, &msg->body[3]);
+       } else
+#endif
+               writel(NINE_WORD_MSG_SIZE | SGL_OFFSET_7, &msg->u.head[0]);
+
+       writel(0xD4000000 | count, mptr++);
+       writel(buffer.phys, mptr);
+
+       writel(function << 24 | HOST_TID << 12 | ADAPTER_TID, &msg->u.head[1]);
+       writel(i2o_config_driver.context, &msg->u.head[2]);
+       writel(0, &msg->u.head[3]);
+
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+       if (!c->adaptec)
+#endif
+       {
+               writel((u32) swtype << 16 | (u32) 1 << 8, &msg->body[0]);
+               writel(0, &msg->body[1]);
+               writel(swid, &msg->body[2]);
+       }
+
+       status = i2o_msg_post_wait_mem(c, m, 60, &buffer);
+
+       if (status != -ETIMEDOUT)
+               i2o_dma_free(&c->pdev->dev, &buffer);
+
+       if (status != I2O_POST_WAIT_OK)
+               return -EIO;
+
+       *offset += count;
+
+       return count;
+
+      free_buffer:
+       i2o_dma_free(&c->pdev->dev, &buffer);
+
+      nop_msg:
+       i2o_msg_nop(c, m);
+
+       return rc;
+};
+
+/* attribute for HRT in sysfs */
+static struct bin_attribute i2o_config_hrt_attr = {
+       .attr = {
+                .name = "hrt",
+                .mode = S_IRUGO,
+                .owner = THIS_MODULE},
+       .size = 0,
+       .read = i2o_config_read_hrt
+};
+
+/* attribute for LCT in sysfs */
+static struct bin_attribute i2o_config_lct_attr = {
+       .attr = {
+                .name = "lct",
+                .mode = S_IRUGO,
+                .owner = THIS_MODULE},
+       .size = 0,
+       .read = i2o_config_read_lct
+};
+
+/* IRTOS firmware access */
+I2O_CONFIG_SW_ATTR(irtos, S_IWRSR, I2O_SOFTWARE_MODULE_IRTOS, 0);
+
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+
+/*
+ * attribute for BIOS / SMOR, nvram and serial number access on DPT / Adaptec
+ * controllers
+ */
+I2O_CONFIG_SW_ATTR(bios, S_IWRSR, I2O_SOFTWARE_MODULE_IOP_PRIVATE, 0);
+I2O_CONFIG_SW_ATTR(nvram, S_IWRSR, I2O_SOFTWARE_MODULE_IOP_CONFIG, 0);
+I2O_CONFIG_SW_ATTR(serial, S_IWRSR, I2O_SOFTWARE_MODULE_IOP_CONFIG, 1);
+
+#endif
+
+/**
+ *     i2o_config_notify_controller_add - Notify of added controller
+ *     @c: the controller which was added
+ *
+ *     If a I2O controller is added, we catch the notification to add sysfs
+ *     entries.
+ */
+static void i2o_config_notify_controller_add(struct i2o_controller *c)
+{
+       struct kobject *kobj = &c->exec->device.kobj;
+
+       sysfs_create_bin_file(kobj, &i2o_config_hrt_attr);
+       sysfs_create_bin_file(kobj, &i2o_config_lct_attr);
+
+       sysfs_create_fops_file(kobj, &i2o_config_attr_irtos);
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+       if (c->adaptec) {
+               sysfs_create_fops_file(kobj, &i2o_config_attr_bios);
+               sysfs_create_fops_file(kobj, &i2o_config_attr_nvram);
+               sysfs_create_fops_file(kobj, &i2o_config_attr_serial);
+       }
+#endif
+};
+
+/**
+ *     i2o_config_notify_controller_remove - Notify of removed controller
+ *     @c: the controller which was removed
+ *
+ *     If a I2O controller is removed, we catch the notification to remove the
+ *     sysfs entries.
+ */
+static void i2o_config_notify_controller_remove(struct i2o_controller *c)
+{
+       struct kobject *kobj = &c->exec->device.kobj;
+
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+       if (c->adaptec) {
+               sysfs_remove_fops_file(kobj, &i2o_config_attr_serial);
+               sysfs_remove_fops_file(kobj, &i2o_config_attr_nvram);
+               sysfs_remove_fops_file(kobj, &i2o_config_attr_bios);
+       }
+#endif
+       sysfs_remove_fops_file(kobj, &i2o_config_attr_irtos);
+
+       sysfs_remove_bin_file(kobj, &i2o_config_lct_attr);
+       sysfs_remove_bin_file(kobj, &i2o_config_hrt_attr);
+};
+
+/* Config OSM driver struct */
+static struct i2o_driver i2o_config_driver = {
+       .name = OSM_NAME,
+       .notify_controller_add = i2o_config_notify_controller_add,
+       .notify_controller_remove = i2o_config_notify_controller_remove
+};
+
+#ifdef CONFIG_I2O_CONFIG_OLD_IOCTL
+#include "i2o_config.c"
+#endif
+
+/**
+ *     i2o_config_init - Configuration OSM initialization function
+ *
+ *     Registers Configuration OSM in the I2O core and if old ioctl's are
+ *     compiled in initialize them.
+ *
+ *     Returns 0 on success or negative error code on failure.
+ */
+static int __init i2o_config_init(void)
+{
+       printk(KERN_INFO OSM_DESCRIPTION " v" OSM_VERSION "\n");
+
+       if (i2o_driver_register(&i2o_config_driver)) {
+               osm_err("handler register failed.\n");
+               return -EBUSY;
+       }
+#ifdef CONFIG_I2O_CONFIG_OLD_IOCTL
+       if (i2o_config_old_init())
+               i2o_driver_unregister(&i2o_config_driver);
+#endif
+
+       return 0;
+}
+
+/**
+ *     i2o_config_exit - Configuration OSM exit function
+ *
+ *     If old ioctl's are compiled in exit remove them and unregisters
+ *     Configuration OSM from I2O core.
+ */
+static void i2o_config_exit(void)
+{
+#ifdef CONFIG_I2O_CONFIG_OLD_IOCTL
+       i2o_config_old_exit();
+#endif
+
+       i2o_driver_unregister(&i2o_config_driver);
+}
+
+MODULE_AUTHOR("Markus Lidel <Markus.Lidel@shadowconnect.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION(OSM_DESCRIPTION);
+MODULE_VERSION(OSM_VERSION);
+
+module_init(i2o_config_init);
+module_exit(i2o_config_exit);
index bebdd509b5d84209bf64145764d28b90613f0bc5..393be8e2914cd99fd00e6705cf945aa7cd6eff2e 100644 (file)
@@ -180,7 +180,13 @@ int i2o_driver_dispatch(struct i2o_controller *c, u32 m)
 {
        struct i2o_driver *drv;
        struct i2o_message __iomem *msg = i2o_msg_out_to_virt(c, m);
-       u32 context = readl(&msg->u.s.icntxt);
+       u32 context;
+       unsigned long flags;
+
+       if(unlikely(!msg))
+               return -EIO;
+
+       context = readl(&msg->u.s.icntxt);
 
        if (unlikely(context >= i2o_max_drivers)) {
                osm_warn("%s: Spurious reply to unknown driver %d\n", c->name,
@@ -188,9 +194,9 @@ int i2o_driver_dispatch(struct i2o_controller *c, u32 m)
                return -EIO;
        }
 
-       spin_lock(&i2o_drivers_lock);
+       spin_lock_irqsave(&i2o_drivers_lock, flags);
        drv = i2o_drivers[context];
-       spin_unlock(&i2o_drivers_lock);
+       spin_unlock_irqrestore(&i2o_drivers_lock, flags);
 
        if (unlikely(!drv)) {
                osm_warn("%s: Spurious reply to unknown driver %d\n", c->name,
index 5581344fbba6e404b50ccf474b740fcaac08ab6d..0160221c802a3068c051fc1bc5362a7ff3635d8c 100644 (file)
@@ -206,6 +206,7 @@ static int i2o_msg_post_wait_complete(struct i2o_controller *c, u32 m,
                                      u32 context)
 {
        struct i2o_exec_wait *wait, *tmp;
+       unsigned long flags;
        static spinlock_t lock = SPIN_LOCK_UNLOCKED;
        int rc = 1;
 
@@ -216,11 +217,13 @@ static int i2o_msg_post_wait_complete(struct i2o_controller *c, u32 m,
         * already expired. Not much we can do about that except log it for
         * debug purposes, increase timeout, and recompile.
         */
-       spin_lock(&lock);
+       spin_lock_irqsave(&lock, flags);
        list_for_each_entry_safe(wait, tmp, &i2o_exec_wait_list, list) {
                if (wait->tcntxt == context) {
                        list_del(&wait->list);
 
+                       spin_unlock_irqrestore(&lock, flags);
+
                        wait->m = m;
                        wait->msg = msg;
                        wait->complete = 1;
@@ -242,13 +245,11 @@ static int i2o_msg_post_wait_complete(struct i2o_controller *c, u32 m,
                                rc = -1;
                        }
 
-                       spin_unlock(&lock);
-
                        return rc;
                }
        }
 
-       spin_unlock(&lock);
+       spin_unlock_irqrestore(&lock, flags);
 
        osm_warn("%s: Bogus reply in POST WAIT (tr-context: %08x)!\n", c->name,
                 context);
@@ -256,6 +257,50 @@ static int i2o_msg_post_wait_complete(struct i2o_controller *c, u32 m,
        return -1;
 };
 
+/**
+ *     i2o_exec_show_vendor_id - Displays Vendor ID of controller
+ *     @d: device of which the Vendor ID should be displayed
+ *     @buf: buffer into which the Vendor ID should be printed
+ *
+ *     Returns number of bytes printed into buffer.
+ */
+static ssize_t i2o_exec_show_vendor_id(struct device *d, char *buf)
+{
+       struct i2o_device *dev = to_i2o_device(d);
+       u16 id;
+
+       if (i2o_parm_field_get(dev, 0x0000, 0, &id, 2)) {
+               sprintf(buf, "0x%04x", id);
+               return strlen(buf) + 1;
+       }
+
+       return 0;
+};
+
+/**
+ *     i2o_exec_show_product_id - Displays Product ID of controller
+ *     @d: device of which the Product ID should be displayed
+ *     @buf: buffer into which the Product ID should be printed
+ *
+ *     Returns number of bytes printed into buffer.
+ */
+static ssize_t i2o_exec_show_product_id(struct device *d, char *buf)
+{
+       struct i2o_device *dev = to_i2o_device(d);
+       u16 id;
+
+       if (i2o_parm_field_get(dev, 0x0000, 1, &id, 2)) {
+               sprintf(buf, "0x%04x", id);
+               return strlen(buf) + 1;
+       }
+
+       return 0;
+};
+
+/* Exec-OSM device attributes */
+static DEVICE_ATTR(vendor_id, S_IRUGO, i2o_exec_show_vendor_id, NULL);
+static DEVICE_ATTR(product_id, S_IRUGO, i2o_exec_show_product_id, NULL);
+
 /**
  *     i2o_exec_probe - Called if a new I2O device (executive class) appears
  *     @dev: I2O device which should be probed
@@ -268,10 +313,16 @@ static int i2o_msg_post_wait_complete(struct i2o_controller *c, u32 m,
 static int i2o_exec_probe(struct device *dev)
 {
        struct i2o_device *i2o_dev = to_i2o_device(dev);
+       struct i2o_controller *c = i2o_dev->iop;
 
        i2o_event_register(i2o_dev, &i2o_exec_driver, 0, 0xffffffff);
 
-       i2o_dev->iop->exec = i2o_dev;
+       c->exec = i2o_dev;
+
+       i2o_exec_lct_notify(c, c->lct->change_ind + 1);
+
+       device_create_file(dev, &dev_attr_vendor_id);
+       device_create_file(dev, &dev_attr_product_id);
 
        return 0;
 };
@@ -286,6 +337,9 @@ static int i2o_exec_probe(struct device *dev)
  */
 static int i2o_exec_remove(struct device *dev)
 {
+       device_remove_file(dev, &dev_attr_product_id);
+       device_remove_file(dev, &dev_attr_vendor_id);
+
        i2o_event_register(to_i2o_device(dev), &i2o_exec_driver, 0, 0);
 
        return 0;
@@ -297,12 +351,16 @@ static int i2o_exec_remove(struct device *dev)
  *
  *     This function handles asynchronus LCT NOTIFY replies. It parses the
  *     new LCT and if the buffer for the LCT was to small sends a LCT NOTIFY
- *     again.
+ *     again, otherwise send LCT NOTIFY to get informed on next LCT change.
  */
 static void i2o_exec_lct_modified(struct i2o_controller *c)
 {
-       if (i2o_device_parse_lct(c) == -EAGAIN)
-               i2o_exec_lct_notify(c, 0);
+       u32 change_ind = 0;
+
+       if (i2o_device_parse_lct(c) != -EAGAIN)
+               change_ind = c->lct->change_ind + 1;
+
+       i2o_exec_lct_notify(c, change_ind);
 };
 
 /**
index e69421e36ac510e85ad68320e62b9ebe79c0e937..1dd2b9dad50e8e36b5fca7f92a3712e4e6ee9046 100644 (file)
@@ -146,6 +146,29 @@ static int i2o_block_device_flush(struct i2o_device *dev)
        return i2o_msg_post_wait(dev->iop, m, 60);
 };
 
+/**
+ *     i2o_block_issue_flush - device-flush interface for block-layer
+ *     @queue: the request queue of the device which should be flushed
+ *     @disk: gendisk
+ *     @error_sector: error offset
+ *
+ *     Helper function to provide flush functionality to block-layer.
+ *
+ *     Returns 0 on success or negative error code on failure.
+ */
+
+static int i2o_block_issue_flush(request_queue_t * queue, struct gendisk *disk,
+                                sector_t * error_sector)
+{
+       struct i2o_block_device *i2o_blk_dev = queue->queuedata;
+       int rc = -ENODEV;
+
+       if (likely(i2o_blk_dev))
+               rc = i2o_block_device_flush(i2o_blk_dev->i2o_dev);
+
+       return rc;
+}
+
 /**
  *     i2o_block_device_mount - Mount (load) the media of device dev
  *     @dev: I2O device which should receive the mount request
@@ -299,28 +322,31 @@ static inline void i2o_block_request_free(struct i2o_block_request *ireq)
 
 /**
  *     i2o_block_sglist_alloc - Allocate the SG list and map it
+ *     @c: I2O controller to which the request belongs
  *     @ireq: I2O block request
  *
- *     Builds the SG list and map it into to be accessable by the controller.
+ *     Builds the SG list and map it to be accessable by the controller.
  *
- *     Returns the number of elements in the SG list or 0 on failure.
+ *     Returns 0 on failure or 1 on success.
  */
-static inline int i2o_block_sglist_alloc(struct i2o_block_request *ireq)
+static inline int i2o_block_sglist_alloc(struct i2o_controller *c,
+                                        struct i2o_block_request *ireq,
+                                        u32 __iomem ** mptr)
 {
-       struct device *dev = &ireq->i2o_blk_dev->i2o_dev->iop->pdev->dev;
        int nents;
+       enum dma_data_direction direction;
 
+       ireq->dev = &c->pdev->dev;
        nents = blk_rq_map_sg(ireq->req->q, ireq->req, ireq->sg_table);
 
        if (rq_data_dir(ireq->req) == READ)
-               ireq->sg_dma_direction = PCI_DMA_FROMDEVICE;
+               direction = PCI_DMA_FROMDEVICE;
        else
-               ireq->sg_dma_direction = PCI_DMA_TODEVICE;
+               direction = PCI_DMA_TODEVICE;
 
-       ireq->sg_nents = dma_map_sg(dev, ireq->sg_table, nents,
-                                   ireq->sg_dma_direction);
+       ireq->sg_nents = nents;
 
-       return ireq->sg_nents;
+       return i2o_dma_map_sg(c, ireq->sg_table, nents, direction, mptr);
 };
 
 /**
@@ -331,10 +357,14 @@ static inline int i2o_block_sglist_alloc(struct i2o_block_request *ireq)
  */
 static inline void i2o_block_sglist_free(struct i2o_block_request *ireq)
 {
-       struct device *dev = &ireq->i2o_blk_dev->i2o_dev->iop->pdev->dev;
+       enum dma_data_direction direction;
 
-       dma_unmap_sg(dev, ireq->sg_table, ireq->sg_nents,
-                    ireq->sg_dma_direction);
+       if (rq_data_dir(ireq->req) == READ)
+               direction = PCI_DMA_FROMDEVICE;
+       else
+               direction = PCI_DMA_TODEVICE;
+
+       dma_unmap_sg(ireq->dev, ireq->sg_table, ireq->sg_nents, direction);
 };
 
 /**
@@ -352,6 +382,11 @@ static int i2o_block_prep_req_fn(struct request_queue *q, struct request *req)
        struct i2o_block_device *i2o_blk_dev = q->queuedata;
        struct i2o_block_request *ireq;
 
+       if (unlikely(!i2o_blk_dev)) {
+               osm_err("block device already removed\n");
+               return BLKPREP_KILL;
+       }
+
        /* request is already processed by us, so return */
        if (req->flags & REQ_SPECIAL) {
                osm_debug("REQ_SPECIAL already set!\n");
@@ -414,11 +449,11 @@ static void i2o_block_end_request(struct request *req, int uptodate,
 {
        struct i2o_block_request *ireq = req->special;
        struct i2o_block_device *dev = ireq->i2o_blk_dev;
-       request_queue_t *q = dev->gd->queue;
+       request_queue_t *q = req->q;
        unsigned long flags;
 
        if (end_that_request_chunk(req, uptodate, nr_bytes)) {
-               int leftover = (req->hard_nr_sectors << 9);
+               int leftover = (req->hard_nr_sectors << KERNEL_SECTOR_SHIFT);
 
                if (blk_pc_request(req))
                        leftover = req->data_len;
@@ -432,8 +467,11 @@ static void i2o_block_end_request(struct request *req, int uptodate,
        spin_lock_irqsave(q->queue_lock, flags);
 
        end_that_request_last(req);
-       dev->open_queue_depth--;
-       list_del(&ireq->queue);
+
+       if (likely(dev)) {
+               dev->open_queue_depth--;
+               list_del(&ireq->queue);
+       }
 
        blk_start_queue(q);
 
@@ -483,8 +521,8 @@ static int i2o_block_reply(struct i2o_controller *c, u32 m,
                 *      Don't stick a supertrak100 into cache aggressive modes
                 */
 
-               osm_err("%03x error status: %02x, detailed status: %04x\n",
-                       (le32_to_cpu(msg->u.head[1]) >> 12 & 0xfff),
+               osm_err("TID %03x error status: 0x%02x, detailed status: "
+                       "0x%04x\n", (le32_to_cpu(msg->u.head[1]) >> 12 & 0xfff),
                        status >> 24, status & 0xffff);
 
                req->errors++;
@@ -705,18 +743,25 @@ static int i2o_block_media_changed(struct gendisk *disk)
 static int i2o_block_transfer(struct request *req)
 {
        struct i2o_block_device *dev = req->rq_disk->private_data;
-       struct i2o_controller *c = dev->i2o_dev->iop;
+       struct i2o_controller *c;
        int tid = dev->i2o_dev->lct_data.tid;
        struct i2o_message __iomem *msg;
-       void __iomem *mptr;
+       u32 __iomem *mptr;
        struct i2o_block_request *ireq = req->special;
-       struct scatterlist *sg;
-       int sgnum;
-       int i;
        u32 m;
        u32 tcntxt;
-       u32 sg_flags;
+       u32 sgl_offset = SGL_OFFSET_8;
+       u32 ctl_flags = 0x00000000;
        int rc;
+       u32 cmd;
+
+       if (unlikely(!dev->i2o_dev)) {
+               osm_err("transfer to removed drive\n");
+               rc = -ENODEV;
+               goto exit;
+       }
+
+       c = dev->i2o_dev->iop;
 
        m = i2o_msg_get(c, &msg);
        if (m == I2O_QUEUE_EMPTY) {
@@ -730,80 +775,109 @@ static int i2o_block_transfer(struct request *req)
                goto nop_msg;
        }
 
-       if ((sgnum = i2o_block_sglist_alloc(ireq)) <= 0) {
-               rc = -ENOMEM;
-               goto context_remove;
-       }
-
-       /* Build the message based on the request. */
        writel(i2o_block_driver.context, &msg->u.s.icntxt);
        writel(tcntxt, &msg->u.s.tcntxt);
-       writel(req->nr_sectors << 9, &msg->body[1]);
 
-       writel((((u64) req->sector) << 9) & 0xffffffff, &msg->body[2]);
-       writel(req->sector >> 23, &msg->body[3]);
-
-       mptr = &msg->body[4];
-
-       sg = ireq->sg_table;
+       mptr = &msg->body[0];
 
        if (rq_data_dir(req) == READ) {
-               writel(I2O_CMD_BLOCK_READ << 24 | HOST_TID << 12 | tid,
-                      &msg->u.head[1]);
-               sg_flags = 0x10000000;
+               cmd = I2O_CMD_BLOCK_READ << 24;
+
                switch (dev->rcache) {
-               case CACHE_NULL:
-                       writel(0, &msg->body[0]);
-                       break;
                case CACHE_PREFETCH:
-                       writel(0x201F0008, &msg->body[0]);
+                       ctl_flags = 0x201F0008;
                        break;
+
                case CACHE_SMARTFETCH:
                        if (req->nr_sectors > 16)
-                               writel(0x201F0008, &msg->body[0]);
+                               ctl_flags = 0x201F0008;
                        else
-                               writel(0x001F0000, &msg->body[0]);
+                               ctl_flags = 0x001F0000;
+                       break;
+
+               default:
                        break;
                }
        } else {
-               writel(I2O_CMD_BLOCK_WRITE << 24 | HOST_TID << 12 | tid,
-                      &msg->u.head[1]);
-               sg_flags = 0x14000000;
+               cmd = I2O_CMD_BLOCK_WRITE << 24;
+
                switch (dev->wcache) {
-               case CACHE_NULL:
-                       writel(0, &msg->body[0]);
-                       break;
                case CACHE_WRITETHROUGH:
-                       writel(0x001F0008, &msg->body[0]);
+                       ctl_flags = 0x001F0008;
                        break;
                case CACHE_WRITEBACK:
-                       writel(0x001F0010, &msg->body[0]);
+                       ctl_flags = 0x001F0010;
                        break;
                case CACHE_SMARTBACK:
                        if (req->nr_sectors > 16)
-                               writel(0x001F0004, &msg->body[0]);
+                               ctl_flags = 0x001F0004;
                        else
-                               writel(0x001F0010, &msg->body[0]);
+                               ctl_flags = 0x001F0010;
                        break;
                case CACHE_SMARTTHROUGH:
                        if (req->nr_sectors > 16)
-                               writel(0x001F0004, &msg->body[0]);
+                               ctl_flags = 0x001F0004;
                        else
-                               writel(0x001F0010, &msg->body[0]);
+                               ctl_flags = 0x001F0010;
+               default:
+                       break;
+               }
+       }
+
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+       if (c->adaptec) {
+               u8 cmd[10];
+               u32 scsi_flags;
+               u16 hwsec = queue_hardsect_size(req->q) >> KERNEL_SECTOR_SHIFT;
+
+               memset(cmd, 0, 10);
+
+               sgl_offset = SGL_OFFSET_12;
+
+               writel(I2O_CMD_PRIVATE << 24 | HOST_TID << 12 | tid,
+                      &msg->u.head[1]);
+
+               writel(I2O_VENDOR_DPT << 16 | I2O_CMD_SCSI_EXEC, mptr++);
+               writel(tid, mptr++);
+
+               /*
+                * ENABLE_DISCONNECT
+                * SIMPLE_TAG
+                * RETURN_SENSE_DATA_IN_REPLY_MESSAGE_FRAME
+                */
+               if (rq_data_dir(req) == READ) {
+                       cmd[0] = 0x28;
+                       scsi_flags = 0x60a0000a;
+               } else {
+                       cmd[0] = 0x2A;
+                       scsi_flags = 0xa0a0000a;
                }
+
+               writel(scsi_flags, mptr++);
+
+               *((u32 *) & cmd[2]) = cpu_to_be32(req->sector * hwsec);
+               *((u16 *) & cmd[7]) = cpu_to_be16(req->nr_sectors * hwsec);
+
+               memcpy_toio(mptr, cmd, 10);
+               mptr += 4;
+               writel(req->nr_sectors << KERNEL_SECTOR_SHIFT, mptr++);
+       } else
+#endif
+       {
+               writel(cmd | HOST_TID << 12 | tid, &msg->u.head[1]);
+               writel(ctl_flags, mptr++);
+               writel(req->nr_sectors << KERNEL_SECTOR_SHIFT, mptr++);
+               writel((u32) (req->sector << KERNEL_SECTOR_SHIFT), mptr++);
+               writel(req->sector >> (32 - KERNEL_SECTOR_SHIFT), mptr++);
        }
 
-       for (i = sgnum; i > 0; i--) {
-               if (i == 1)
-                       sg_flags |= 0x80000000;
-               writel(sg_flags | sg_dma_len(sg), mptr);
-               writel(sg_dma_address(sg), mptr + 4);
-               mptr += 8;
-               sg++;
+       if (!i2o_block_sglist_alloc(c, ireq, &mptr)) {
+               rc = -ENOMEM;
+               goto context_remove;
        }
 
-       writel(I2O_MESSAGE_SIZE(mptr - &msg->u.head[0]) | SGL_OFFSET_8,
-              &msg->u.head[0]);
+       writel(I2O_MESSAGE_SIZE(mptr - &msg->u.head[0]) |
+              sgl_offset, &msg->u.head[0]);
 
        list_add_tail(&ireq->queue, &dev->open_queue);
        dev->open_queue_depth++;
@@ -846,11 +920,13 @@ static void i2o_block_request_fn(struct request_queue *q)
 
                        queue_depth = ireq->i2o_blk_dev->open_queue_depth;
 
-                       if (queue_depth < I2O_BLOCK_MAX_OPEN_REQUESTS)
+                       if (queue_depth < I2O_BLOCK_MAX_OPEN_REQUESTS) {
                                if (!i2o_block_transfer(req)) {
                                        blkdev_dequeue_request(req);
                                        continue;
-                               }
+                               } else
+                                       osm_info("transfer error\n");
+                       }
 
                        if (queue_depth)
                                break;
@@ -933,6 +1009,7 @@ static struct i2o_block_device *i2o_block_device_alloc(void)
        }
 
        blk_queue_prep_rq(queue, i2o_block_prep_req_fn);
+       blk_queue_issue_flush_fn(queue, i2o_block_issue_flush);
 
        gd->major = I2O_MAJOR;
        gd->queue = queue;
@@ -974,7 +1051,18 @@ static int i2o_block_probe(struct device *dev)
        u64 size;
        u32 blocksize;
        u32 flags, status;
-       int segments;
+       u16 body_size = 4;
+       unsigned short max_sectors;
+
+#ifdef CONFIG_I2O_EXT_ADAPTEC
+       if (c->adaptec)
+               body_size = 8;
+#endif
+
+       if (c->limit_sectors)
+               max_sectors = I2O_MAX_SECTORS_LIMITED;
+       else
+               max_sectors = I2O_MAX_SECTORS;
 
        /* skip devices which are used by IOP */
        if (i2o_dev->lct_data.user_tid != 0xfff) {
@@ -1009,50 +1097,35 @@ static int i2o_block_probe(struct device *dev)
        queue = gd->queue;
        queue->queuedata = i2o_blk_dev;
 
-       blk_queue_max_phys_segments(queue, I2O_MAX_SEGMENTS);
-       blk_queue_max_sectors(queue, I2O_MAX_SECTORS);
-
-       if (c->short_req)
-               segments = 8;
-       else {
-               i2o_status_block *sb;
+       blk_queue_max_phys_segments(queue, I2O_MAX_PHYS_SEGMENTS);
+       blk_queue_max_sectors(queue, max_sectors);
+       blk_queue_max_hw_segments(queue, i2o_sg_tablesize(c, body_size));
 
-               sb = c->status_block.virt;
-
-               segments = (sb->inbound_frame_size -
-                           sizeof(struct i2o_message) / 4 - 4) / 2;
-       }
-
-       blk_queue_max_hw_segments(queue, segments);
-
-       osm_debug("max sectors = %d\n", I2O_MAX_SECTORS);
-       osm_debug("phys segments = %d\n", I2O_MAX_SEGMENTS);
-       osm_debug("hw segments = %d\n", segments);
+       osm_debug("max sectors = %d\n", queue->max_phys_segments);
+       osm_debug("phys segments = %d\n", queue->max_sectors);
+       osm_debug("max hw segments = %d\n", queue->max_hw_segments);
 
        /*
         *      Ask for the current media data. If that isn't supported
         *      then we ask for the device capacity data
         */
-       if (!i2o_parm_field_get(i2o_dev, 0x0004, 0, &size, 8))
-               if (!i2o_parm_field_get(i2o_dev, 0x0000, 4, &size, 8)) {
-                       osm_warn("could not get size of %s\n", gd->disk_name);
-                       size = 0;
-               }
+       if (i2o_parm_field_get(i2o_dev, 0x0004, 1, &blocksize, 4) ||
+           i2o_parm_field_get(i2o_dev, 0x0000, 3, &blocksize, 4)) {
+               blk_queue_hardsect_size(queue, blocksize);
+       } else
+               osm_warn("unable to get blocksize of %s\n", gd->disk_name);
 
-       if (!i2o_parm_field_get(i2o_dev, 0x0004, 1, &blocksize, 4))
-               if (!i2o_parm_field_get(i2o_dev, 0x0000, 3, &blocksize, 4)) {
-                       osm_warn("unable to get blocksize of %s\n",
-                                gd->disk_name);
-                       blocksize = 0;
-               }
+       if (i2o_parm_field_get(i2o_dev, 0x0004, 0, &size, 8) ||
+           i2o_parm_field_get(i2o_dev, 0x0000, 4, &size, 8)) {
+               set_capacity(gd, size >> KERNEL_SECTOR_SHIFT);
+       } else
+               osm_warn("could not get size of %s\n", gd->disk_name);
 
        if (!i2o_parm_field_get(i2o_dev, 0x0000, 2, &i2o_blk_dev->power, 2))
                i2o_blk_dev->power = 0;
        i2o_parm_field_get(i2o_dev, 0x0000, 5, &flags, 4);
        i2o_parm_field_get(i2o_dev, 0x0000, 6, &status, 4);
 
-       set_capacity(gd, size >> 9);
-
        i2o_event_register(i2o_dev, &i2o_block_driver, 0, 0xffffffff);
 
        add_disk(gd);
@@ -1109,7 +1182,7 @@ static int __init i2o_block_init(void)
                goto exit;
        }
 
-       i2o_blk_req_pool.pool = mempool_create(I2O_REQ_MEMPOOL_SIZE,
+       i2o_blk_req_pool.pool = mempool_create(I2O_BLOCK_REQ_MEMPOOL_SIZE,
                                               mempool_alloc_slab,
                                               mempool_free_slab,
                                               i2o_blk_req_pool.slab);
index 712111ffa6387b0429bf2e517cfc44808611ac70..9e1a95fb0833bf464795bc42a14894eaaf262e38 100644 (file)
@@ -84,9 +84,9 @@ struct i2o_block_request
        struct list_head queue;
        struct request *req;            /* corresponding request */
        struct i2o_block_device *i2o_blk_dev;   /* I2O block device */
-       int sg_dma_direction;           /* direction of DMA buffer read/write */
+       struct device *dev;             /* device used for DMA */
        int sg_nents;                   /* number of SG elements */
-       struct scatterlist sg_table[I2O_MAX_SEGMENTS]; /* SG table */
+       struct scatterlist sg_table[I2O_MAX_PHYS_SEGMENTS]; /* SG table */
 };
 
 /* I2O Block device delayed request */
index 383e89a5c9f08a548a596b08693e37b931f60d1d..849d90aad779e200ffb2fe4f9831501fe041a342 100644 (file)
  * 2 of the License, or (at your option) any later version.
  */
 
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/i2o.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/slab.h>
 #include <linux/miscdevice.h>
-#include <linux/mm.h>
-#include <linux/spinlock.h>
 #include <linux/smp_lock.h>
-#include <linux/ioctl32.h>
 #include <linux/compat.h>
-#include <linux/syscalls.h>
 
 #include <asm/uaccess.h>
-#include <asm/io.h>
-
-#define OSM_NAME       "config-osm"
-#define OSM_VERSION    "$Rev$"
-#define OSM_DESCRIPTION        "I2O Configuration OSM"
 
 extern int i2o_parm_issue(struct i2o_device *, int, void *, int, void *, int);
 
@@ -80,125 +64,6 @@ struct i2o_cfg_info {
 static struct i2o_cfg_info *open_files = NULL;
 static ulong i2o_cfg_info_id = 0;
 
-/**
- *     i2o_config_read_hrt - Returns the HRT of the controller
- *     @kob: kernel object handle
- *     @buf: buffer into which the HRT should be copied
- *     @off: file offset
- *     @count: number of bytes to read
- *
- *     Put @count bytes starting at @off into @buf from the HRT of the I2O
- *     controller corresponding to @kobj.
- *
- *     Returns number of bytes copied into buffer.
- */
-static ssize_t i2o_config_read_hrt(struct kobject *kobj, char *buf,
-                                  loff_t offset, size_t count)
-{
-       struct i2o_controller *c = to_i2o_controller(container_of(kobj,
-                                                                 struct device,
-                                                                 kobj));
-       i2o_hrt *hrt = c->hrt.virt;
-
-       u32 size = (hrt->num_entries * hrt->entry_len + 2) * 4;
-
-       if(offset > size)
-               return 0;
-
-       if(offset + count > size)
-               count = size - offset;
-
-       memcpy(buf, (u8 *) hrt + offset, count);
-
-       return count;
-};
-
-/**
- *     i2o_config_read_lct - Returns the LCT of the controller
- *     @kob: kernel object handle
- *     @buf: buffer into which the LCT should be copied
- *     @off: file offset
- *     @count: number of bytes to read
- *
- *     Put @count bytes starting at @off into @buf from the LCT of the I2O
- *     controller corresponding to @kobj.
- *
- *     Returns number of bytes copied into buffer.
- */
-static ssize_t i2o_config_read_lct(struct kobject *kobj, char *buf,
-                                  loff_t offset, size_t count)
-{
-       struct i2o_controller *c = to_i2o_controller(container_of(kobj,
-                                                                 struct device,
-                                                                 kobj));
-       u32 size = c->lct->table_size * 4;
-
-       if(offset > size)
-               return 0;
-
-       if(offset + count > size)
-               count = size - offset;
-
-       memcpy(buf, (u8 *) c->lct + offset, count);
-
-       return count;
-};
-
-/* attribute for HRT in sysfs */
-static struct bin_attribute i2o_config_hrt_attr = {
-       .attr = {
-               .name = "hrt",
-               .mode = S_IRUGO,
-               .owner = THIS_MODULE
-       },
-       .size = 0,
-       .read = i2o_config_read_hrt
-};
-
-/* attribute for LCT in sysfs */
-static struct bin_attribute i2o_config_lct_attr = {
-       .attr = {
-               .name = "lct",
-               .mode = S_IRUGO,
-               .owner = THIS_MODULE
-       },
-       .size = 0,
-       .read = i2o_config_read_lct
-};
-
-/**
- *     i2o_config_notify_controller_add - Notify of added controller
- *     @c: the controller which was added
- *
- *     If a I2O controller is added, we catch the notification to add sysfs
- *     entries.
- */
-static void i2o_config_notify_controller_add(struct i2o_controller *c)
-{
-       sysfs_create_bin_file(&(c->device.kobj), &i2o_config_hrt_attr);
-       sysfs_create_bin_file(&(c->device.kobj), &i2o_config_lct_attr);
-};
-
-/**
- *     i2o_config_notify_controller_remove - Notify of removed controller
- *     @c: the controller which was removed
- *
- *     If a I2O controller is removed, we catch the notification to remove the
- *     sysfs entries.
- */
-static void i2o_config_notify_controller_remove(struct i2o_controller *c)
-{
-       sysfs_remove_bin_file(&c->device.kobj, &i2o_config_lct_attr);
-       sysfs_remove_bin_file(&c->device.kobj, &i2o_config_hrt_attr);
-};
-
-/* Config OSM driver struct */
-static struct i2o_driver i2o_config_driver = {
-       .name = OSM_NAME,
-       .notify_controller_add = i2o_config_notify_controller_add,
-       .notify_controller_remove = i2o_config_notify_controller_remove
-};
-
 static int i2o_cfg_getiops(unsigned long arg)
 {
        struct i2o_controller *c;
@@ -1257,37 +1122,20 @@ static struct miscdevice i2o_miscdev = {
        &config_fops
 };
 
-static int __init i2o_config_init(void)
+static int __init i2o_config_old_init(void)
 {
-       printk(KERN_INFO OSM_DESCRIPTION " v" OSM_VERSION "\n");
-
        spin_lock_init(&i2o_config_lock);
 
        if (misc_register(&i2o_miscdev) < 0) {
                osm_err("can't register device.\n");
                return -EBUSY;
        }
-       /*
-        *      Install our handler
-        */
-       if (i2o_driver_register(&i2o_config_driver)) {
-               osm_err("handler register failed.\n");
-               misc_deregister(&i2o_miscdev);
-               return -EBUSY;
-       }
        return 0;
 }
 
-static void i2o_config_exit(void)
+static void i2o_config_old_exit(void)
 {
        misc_deregister(&i2o_miscdev);
-       i2o_driver_unregister(&i2o_config_driver);
 }
 
 MODULE_AUTHOR("Red Hat Software");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION(OSM_DESCRIPTION);
-MODULE_VERSION(OSM_VERSION);
-
-module_init(i2o_config_init);
-module_exit(i2o_config_exit);
index b176d0eeff7f05934874a22fea6081c0752fb30d..e5b74452c4955d44b35e5ae49f0f510b5e7f76c6 100644 (file)
@@ -228,7 +228,7 @@ static const char *i2o_get_class_name(int class)
        case I2O_CLASS_FLOPPY_DEVICE:
                idx = 12;
                break;
-       case I2O_CLASS_BUS_ADAPTER_PORT:
+       case I2O_CLASS_BUS_ADAPTER:
                idx = 13;
                break;
        case I2O_CLASS_PEER_TRANSPORT_AGENT:
@@ -490,7 +490,7 @@ static int i2o_seq_show_lct(struct seq_file *seq, void *v)
                                seq_printf(seq, ", Unknown Device Type");
                        break;
 
-               case I2O_CLASS_BUS_ADAPTER_PORT:
+               case I2O_CLASS_BUS_ADAPTER:
                        if (lct->lct_entry[i].sub_class < BUS_TABLE_SIZE)
                                seq_printf(seq, ", %s",
                                           bus_ports[lct->lct_entry[i].
index 812c29ec86d3a7cc83a2bd7adb1efe29bf2e12a9..c3b0c29ac02da5efc382358990b60ae19130409b 100644 (file)
@@ -103,7 +103,7 @@ static struct i2o_scsi_host *i2o_scsi_host_alloc(struct i2o_controller *c)
        i2o_status_block *sb;
 
        list_for_each_entry(i2o_dev, &c->devices, list)
-           if (i2o_dev->lct_data.class_id == I2O_CLASS_BUS_ADAPTER_PORT) {
+           if (i2o_dev->lct_data.class_id == I2O_CLASS_BUS_ADAPTER) {
                if (i2o_parm_field_get(i2o_dev, 0x0000, 0, &type, 1)
                   && (type == 0x01))   /* SCSI bus */
                        max_channel++;
@@ -139,7 +139,7 @@ static struct i2o_scsi_host *i2o_scsi_host_alloc(struct i2o_controller *c)
 
        i = 0;
        list_for_each_entry(i2o_dev, &c->devices, list)
-           if (i2o_dev->lct_data.class_id == I2O_CLASS_BUS_ADAPTER_PORT) {
+           if (i2o_dev->lct_data.class_id == I2O_CLASS_BUS_ADAPTER) {
                if (i2o_parm_field_get(i2o_dev, 0x0000, 0, &type, 1) || (type == 1))    /* only SCSI bus */
                        i2o_shost->channel[i++] = i2o_dev;
 
@@ -186,6 +186,7 @@ static int i2o_scsi_remove(struct device *dev)
 
        shost_for_each_device(scsi_dev, i2o_shost->scsi_host)
            if (scsi_dev->hostdata == i2o_dev) {
+               sysfs_remove_link(&i2o_dev->device.kobj, "scsi");
                scsi_remove_device(scsi_dev);
                scsi_device_put(scsi_dev);
                break;
@@ -259,12 +260,14 @@ static int i2o_scsi_probe(struct device *dev)
        scsi_dev =
            __scsi_add_device(i2o_shost->scsi_host, channel, id, lun, i2o_dev);
 
-       if (!scsi_dev) {
+       if (IS_ERR(scsi_dev)) {
                osm_warn("can not add SCSI device %03x\n",
                         i2o_dev->lct_data.tid);
-               return -EFAULT;
+               return PTR_ERR(scsi_dev);
        }
 
+       sysfs_create_link(&i2o_dev->device.kobj, &scsi_dev->sdev_gendev.kobj, "scsi");
+
        osm_info("device added (TID: %03x) channel: %d, id: %d, lun: %d\n",
                 i2o_dev->lct_data.tid, channel, id, (unsigned int)lun);
 
@@ -545,7 +548,13 @@ static int i2o_scsi_queuecommand(struct scsi_cmnd *SCpnt,
        int tid;
        struct i2o_message __iomem *msg;
        u32 m;
-       u32 scsi_flags, sg_flags;
+       /*
+        * ENABLE_DISCONNECT
+        * SIMPLE_TAG
+        * RETURN_SENSE_DATA_IN_REPLY_MESSAGE_FRAME
+        */
+       u32 scsi_flags = 0x20a00000;
+       u32 sg_flags;
        u32 __iomem *mptr;
        u32 __iomem *lenptr;
        u32 len;
@@ -591,17 +600,19 @@ static int i2o_scsi_queuecommand(struct scsi_cmnd *SCpnt,
 
        switch (SCpnt->sc_data_direction) {
        case PCI_DMA_NONE:
-               scsi_flags = 0x00000000;        // DATA NO XFER
+               /* DATA NO XFER */
                sg_flags = 0x00000000;
                break;
 
        case PCI_DMA_TODEVICE:
-               scsi_flags = 0x80000000;        // DATA OUT (iop-->dev)
+               /* DATA OUT (iop-->dev) */
+               scsi_flags |= 0x80000000;
                sg_flags = 0x14000000;
                break;
 
        case PCI_DMA_FROMDEVICE:
-               scsi_flags = 0x40000000;        // DATA IN  (iop<--dev)
+               /* DATA IN  (iop<--dev) */
+               scsi_flags |= 0x40000000;
                sg_flags = 0x10000000;
                break;
 
@@ -639,8 +650,7 @@ static int i2o_scsi_queuecommand(struct scsi_cmnd *SCpnt,
           }
         */
 
-       /* Direction, disconnect ok, tag, CDBLen */
-       writel(scsi_flags | 0x20200000 | SCpnt->cmd_len, mptr ++);
+       writel(scsi_flags | SCpnt->cmd_len, mptr++);
 
        /* Write SCSI command into the message - always 16 byte block */
        memcpy_toio(mptr, SCpnt->cmnd, 16);
index 62b0d8bed186db9a25bde1dbe920b1c442689db7..40312053b38d2928a78c922b41216a4c9c8a6ec6 100644 (file)
@@ -455,6 +455,70 @@ static int i2o_iop_clear(struct i2o_controller *c)
        return rc;
 }
 
+/**
+ *     i2o_iop_init_outbound_queue - setup the outbound message queue
+ *     @c: I2O controller
+ *
+ *     Clear and (re)initialize IOP's outbound queue and post the message
+ *     frames to the IOP.
+ *
+ *     Returns 0 on success or a negative errno code on failure.
+ */
+static int i2o_iop_init_outbound_queue(struct i2o_controller *c)
+{
+       u8 *status = c->status.virt;
+       u32 m;
+       struct i2o_message __iomem *msg;
+       ulong timeout;
+       int i;
+
+       osm_debug("%s: Initializing Outbound Queue...\n", c->name);
+
+       memset(status, 0, 4);
+
+       m = i2o_msg_get_wait(c, &msg, I2O_TIMEOUT_MESSAGE_GET);
+       if (m == I2O_QUEUE_EMPTY)
+               return -ETIMEDOUT;
+
+       writel(EIGHT_WORD_MSG_SIZE | TRL_OFFSET_6, &msg->u.head[0]);
+       writel(I2O_CMD_OUTBOUND_INIT << 24 | HOST_TID << 12 | ADAPTER_TID,
+              &msg->u.head[1]);
+       writel(i2o_exec_driver.context, &msg->u.s.icntxt);
+       writel(0x0106, &msg->u.s.tcntxt);       /* FIXME: why 0x0106, maybe in
+                                                  Spec? */
+       writel(PAGE_SIZE, &msg->body[0]);
+       /* Outbound msg frame size in words and Initcode */
+       writel(MSG_FRAME_SIZE << 16 | 0x80, &msg->body[1]);
+       writel(0xd0000004, &msg->body[2]);
+       writel(i2o_dma_low(c->status.phys), &msg->body[3]);
+       writel(i2o_dma_high(c->status.phys), &msg->body[4]);
+
+       i2o_msg_post(c, m);
+
+       timeout = jiffies + I2O_TIMEOUT_INIT_OUTBOUND_QUEUE * HZ;
+       while (*status <= I2O_CMD_IN_PROGRESS) {
+               if (time_after(jiffies, timeout)) {
+                       osm_warn("%s: Timeout Initializing\n", c->name);
+                       return -ETIMEDOUT;
+               }
+               set_current_state(TASK_UNINTERRUPTIBLE);
+               schedule_timeout(1);
+
+               rmb();
+       }
+
+       m = c->out_queue.phys;
+
+       /* Post frames */
+       for (i = 0; i < NMBR_MSG_FRAMES; i++) {
+               i2o_flush_reply(c, m);
+               udelay(1);      /* Promise */
+               m += MSG_FRAME_SIZE * 4;
+       }
+
+       return 0;
+}
+
 /**
  *     i2o_iop_reset - reset an I2O controller
  *     @c: controller to reset
@@ -491,25 +555,16 @@ static int i2o_iop_reset(struct i2o_controller *c)
        writel(0, &msg->u.s.tcntxt);    //FIXME: use reasonable transaction context
        writel(0, &msg->body[0]);
        writel(0, &msg->body[1]);
-       writel(i2o_ptr_low((void *)c->status.phys), &msg->body[2]);
-       writel(i2o_ptr_high((void *)c->status.phys), &msg->body[3]);
+       writel(i2o_dma_low(c->status.phys), &msg->body[2]);
+       writel(i2o_dma_high(c->status.phys), &msg->body[3]);
 
        i2o_msg_post(c, m);
 
        /* Wait for a reply */
        timeout = jiffies + I2O_TIMEOUT_RESET * HZ;
        while (!*status) {
-               if (time_after(jiffies, timeout)) {
-                       printk(KERN_ERR "%s: IOP reset timeout.\n", c->name);
-                       rc = -ETIMEDOUT;
-                       goto exit;
-               }
-
-               /* Promise bug */
-               if (status[1] || status[4]) {
-                       *status = 0;
+               if (time_after(jiffies, timeout))
                        break;
-               }
 
                set_current_state(TASK_UNINTERRUPTIBLE);
                schedule_timeout(1);
@@ -517,14 +572,20 @@ static int i2o_iop_reset(struct i2o_controller *c)
                rmb();
        }
 
-       if (*status == I2O_CMD_IN_PROGRESS) {
+       switch (*status) {
+       case I2O_CMD_REJECTED:
+               osm_warn("%s: IOP reset rejected\n", c->name);
+               rc = -EPERM;
+               break;
+
+       case I2O_CMD_IN_PROGRESS:
                /*
                 * Once the reset is sent, the IOP goes into the INIT state
-                * which is indeterminate.  We need to wait until the IOP
-                * has rebooted before we can let the system talk to
-                * it. We read the inbound Free_List until a message is
-                * available. If we can't read one in the given ammount of
-                * time, we assume the IOP could not reboot properly.
+                * which is indeterminate. We need to wait until the IOP has
+                * rebooted before we can let the system talk to it. We read
+                * the inbound Free_List until a message is available. If we
+                * can't read one in the given ammount of time, we assume the
+                * IOP could not reboot properly.
                 */
                pr_debug("%s: Reset in progress, waiting for reboot...\n",
                         c->name);
@@ -543,19 +604,26 @@ static int i2o_iop_reset(struct i2o_controller *c)
                        m = i2o_msg_get_wait(c, &msg, I2O_TIMEOUT_RESET);
                }
                i2o_msg_nop(c, m);
-       }
 
-       /* from here all quiesce commands are safe */
-       c->no_quiesce = 0;
+               /* from here all quiesce commands are safe */
+               c->no_quiesce = 0;
 
-       /* If IopReset was rejected or didn't perform reset, try IopClear */
-       i2o_status_get(c);
-       if (*status == I2O_CMD_REJECTED || sb->iop_state != ADAPTER_STATE_RESET) {
-               printk(KERN_WARNING "%s: Reset rejected, trying to clear\n",
-                      c->name);
-               i2o_iop_clear(c);
-       } else
-               pr_debug("%s: Reset completed.\n", c->name);
+               /* verify if controller is in state RESET */
+               i2o_status_get(c);
+
+               if (!c->promise && (sb->iop_state != ADAPTER_STATE_RESET))
+                       osm_warn("%s: reset completed, but adapter not in RESET"
+                                " state.\n", c->name);
+               else
+                       osm_debug("%s: reset completed.\n", c->name);
+
+               break;
+
+       default:
+               osm_err("%s: IOP reset timeout.\n", c->name);
+               rc = -ETIMEDOUT;
+               break;
+       }
 
       exit:
        /* Enable all IOPs */
@@ -564,87 +632,6 @@ static int i2o_iop_reset(struct i2o_controller *c)
        return rc;
 };
 
-/**
- *     i2o_iop_init_outbound_queue - setup the outbound message queue
- *     @c: I2O controller
- *
- *     Clear and (re)initialize IOP's outbound queue and post the message
- *     frames to the IOP.
- *
- *     Returns 0 on success or a negative errno code on failure.
- */
-static int i2o_iop_init_outbound_queue(struct i2o_controller *c)
-{
-       u8 *status = c->status.virt;
-       u32 m;
-       struct i2o_message __iomem *msg;
-       ulong timeout;
-       int i;
-
-       pr_debug("%s: Initializing Outbound Queue...\n", c->name);
-
-       memset(status, 0, 4);
-
-       m = i2o_msg_get_wait(c, &msg, I2O_TIMEOUT_MESSAGE_GET);
-       if (m == I2O_QUEUE_EMPTY)
-               return -ETIMEDOUT;
-
-       writel(EIGHT_WORD_MSG_SIZE | SGL_OFFSET_6, &msg->u.head[0]);
-       writel(I2O_CMD_OUTBOUND_INIT << 24 | HOST_TID << 12 | ADAPTER_TID,
-              &msg->u.head[1]);
-       writel(i2o_exec_driver.context, &msg->u.s.icntxt);
-       writel(0x00000000, &msg->u.s.tcntxt);
-       writel(PAGE_SIZE, &msg->body[0]);
-       writel(MSG_FRAME_SIZE << 16 | 0x80, &msg->body[1]);     /* Outbound msg frame
-                                                                  size in words and Initcode */
-       writel(0xd0000004, &msg->body[2]);
-       writel(i2o_ptr_low((void *)c->status.phys), &msg->body[3]);
-       writel(i2o_ptr_high((void *)c->status.phys), &msg->body[4]);
-
-       i2o_msg_post(c, m);
-
-       timeout = jiffies + I2O_TIMEOUT_INIT_OUTBOUND_QUEUE * HZ;
-       while (*status <= I2O_CMD_IN_PROGRESS) {
-               if (time_after(jiffies, timeout)) {
-                       printk(KERN_WARNING "%s: Timeout Initializing\n",
-                              c->name);
-                       return -ETIMEDOUT;
-               }
-               set_current_state(TASK_UNINTERRUPTIBLE);
-               schedule_timeout(1);
-
-               rmb();
-       }
-
-       m = c->out_queue.phys;
-
-       /* Post frames */
-       for (i = 0; i < NMBR_MSG_FRAMES; i++) {
-               i2o_flush_reply(c, m);
-               udelay(1);      /* Promise */
-               m += MSG_FRAME_SIZE * 4;
-       }
-
-       return 0;
-}
-
-/**
- *     i2o_iop_send_nop - send a core NOP message
- *     @c: controller
- *
- *     Send a no-operation message with a reply set to cause no
- *     action either. Needed for bringing up promise controllers.
- */
-static int i2o_iop_send_nop(struct i2o_controller *c)
-{
-       struct i2o_message __iomem *msg;
-       u32 m = i2o_msg_get_wait(c, &msg, HZ);
-       if (m == I2O_QUEUE_EMPTY)
-               return -ETIMEDOUT;
-       i2o_msg_nop(c, m);
-       return 0;
-}
-
 /**
  *     i2o_iop_activate - Bring controller up to HOLD
  *     @c: controller
@@ -656,26 +643,9 @@ static int i2o_iop_send_nop(struct i2o_controller *c)
  */
 static int i2o_iop_activate(struct i2o_controller *c)
 {
-       struct pci_dev *i960 = NULL;
        i2o_status_block *sb = c->status_block.virt;
        int rc;
-
-       if (c->promise) {
-               /* Beat up the hardware first of all */
-               i960 =
-                   pci_find_slot(c->pdev->bus->number,
-                                 PCI_DEVFN(PCI_SLOT(c->pdev->devfn), 0));
-               if (i960)
-                       pci_write_config_word(i960, 0x42, 0);
-
-               /* Follow this sequence precisely or the controller
-                  ceases to perform useful functions until reboot */
-               if ((rc = i2o_iop_send_nop(c)))
-                       return rc;
-
-               if ((rc = i2o_iop_reset(c)))
-                       return rc;
-       }
+       int state;
 
        /* In INIT state, Wait Inbound Q to initialize (in i2o_status_get) */
        /* In READY state, Get status */
@@ -684,7 +654,8 @@ static int i2o_iop_activate(struct i2o_controller *c)
        if (rc) {
                printk(KERN_INFO "%s: Unable to obtain status, "
                       "attempting a reset.\n", c->name);
-               if (i2o_iop_reset(c))
+               rc = i2o_iop_reset(c);
+               if (rc)
                        return rc;
        }
 
@@ -697,37 +668,37 @@ static int i2o_iop_activate(struct i2o_controller *c)
        switch (sb->iop_state) {
        case ADAPTER_STATE_FAULTED:
                printk(KERN_CRIT "%s: hardware fault\n", c->name);
-               return -ENODEV;
+               return -EFAULT;
 
        case ADAPTER_STATE_READY:
        case ADAPTER_STATE_OPERATIONAL:
        case ADAPTER_STATE_HOLD:
        case ADAPTER_STATE_FAILED:
                pr_debug("%s: already running, trying to reset...\n", c->name);
-               if (i2o_iop_reset(c))
-                       return -ENODEV;
+               rc = i2o_iop_reset(c);
+               if (rc)
+                       return rc;
        }
 
+       /* preserve state */
+       state = sb->iop_state;
+
        rc = i2o_iop_init_outbound_queue(c);
        if (rc)
                return rc;
 
-       if (c->promise) {
-               if ((rc = i2o_iop_send_nop(c)))
-                       return rc;
+       /* if adapter was not in RESET state clear now */
+       if (state != ADAPTER_STATE_RESET)
+               i2o_iop_clear(c);
 
-               if ((rc = i2o_status_get(c)))
-                       return rc;
+       i2o_status_get(c);
 
-               if (i960)
-                       pci_write_config_word(i960, 0x42, 0x3FF);
+       if (sb->iop_state != ADAPTER_STATE_HOLD) {
+               osm_err("%s: failed to bring IOP into HOLD state\n", c->name);
+               return -EIO;
        }
 
-       /* In HOLD state */
-
-       rc = i2o_hrt_get(c);
-
-       return rc;
+       return i2o_hrt_get(c);
 };
 
 /**
@@ -1030,8 +1001,8 @@ int i2o_status_get(struct i2o_controller *c)
        writel(0, &msg->u.s.tcntxt);    // FIXME: use resonable transaction context
        writel(0, &msg->body[0]);
        writel(0, &msg->body[1]);
-       writel(i2o_ptr_low((void *)c->status_block.phys), &msg->body[2]);
-       writel(i2o_ptr_high((void *)c->status_block.phys), &msg->body[3]);
+       writel(i2o_dma_low(c->status_block.phys), &msg->body[2]);
+       writel(i2o_dma_high(c->status_block.phys), &msg->body[3]);
        writel(sizeof(i2o_status_block), &msg->body[4]);        /* always 88 bytes */
 
        i2o_msg_post(c, m);
index f33fd81f77a464d37fd6022bdfaa85ec3b338de6..a499af096a6809710c48ecdc2ed4da0bbe609e09 100644 (file)
@@ -49,30 +49,6 @@ static struct pci_device_id __devinitdata i2o_pci_ids[] = {
        {0}
 };
 
-/**
- *     i2o_dma_realloc - Realloc DMA memory
- *     @dev: struct device pointer to the PCI device of the I2O controller
- *     @addr: pointer to a i2o_dma struct DMA buffer
- *     @len: new length of memory
- *     @gfp_mask: GFP mask
- *
- *     If there was something allocated in the addr, free it first. If len > 0
- *     than try to allocate it and write the addresses back to the addr
- *     structure. If len == 0 set the virtual address to NULL.
- *
- *     Returns the 0 on success or negative error code on failure.
- */
-int i2o_dma_realloc(struct device *dev, struct i2o_dma *addr, size_t len,
-                   unsigned int gfp_mask)
-{
-       i2o_dma_free(dev, addr);
-
-       if (len)
-               return i2o_dma_alloc(dev, addr, len, gfp_mask);
-
-       return 0;
-};
-
 /**
  *     i2o_pci_free - Frees the DMA memory for the I2O controller
  *     @c: I2O controller to free
@@ -185,6 +161,7 @@ static int __devinit i2o_pci_alloc(struct i2o_controller *c)
        } else
                c->in_queue = c->base;
 
+       c->irq_status = c->base.virt + I2O_IRQ_STATUS;
        c->irq_mask = c->base.virt + I2O_IRQ_MASK;
        c->in_port = c->base.virt + I2O_IN_PORT;
        c->out_port = c->base.virt + I2O_OUT_PORT;
@@ -232,36 +209,30 @@ static int __devinit i2o_pci_alloc(struct i2o_controller *c)
 static irqreturn_t i2o_pci_interrupt(int irq, void *dev_id, struct pt_regs *r)
 {
        struct i2o_controller *c = dev_id;
-       struct device *dev = &c->pdev->dev;
-       u32 mv = readl(c->out_port);
-
-       /*
-        * Old 960 steppings had a bug in the I2O unit that caused
-        * the queue to appear empty when it wasn't.
-        */
-       if (mv == I2O_QUEUE_EMPTY) {
-               mv = readl(c->out_port);
-               if (unlikely(mv == I2O_QUEUE_EMPTY))
-                       return IRQ_NONE;
-               else
-                       pr_debug("%s: 960 bug detected\n", c->name);
-       }
+       u32 m;
+       irqreturn_t rc = IRQ_NONE;
+
+       while (readl(c->irq_status) & I2O_IRQ_OUTBOUND_POST) {
+               m = readl(c->out_port);
+               if (m == I2O_QUEUE_EMPTY) {
+                       /*
+                        * Old 960 steppings had a bug in the I2O unit that
+                        * caused the queue to appear empty when it wasn't.
+                        */
+                       m = readl(c->out_port);
+                       if (unlikely(m == I2O_QUEUE_EMPTY))
+                               break;
+               }
 
-       while (mv != I2O_QUEUE_EMPTY) {
                /* dispatch it */
-               if (i2o_driver_dispatch(c, mv))
+               if (i2o_driver_dispatch(c, m))
                        /* flush it if result != 0 */
-                       i2o_flush_reply(c, mv);
+                       i2o_flush_reply(c, m);
 
-               /*
-                * That 960 bug again...
-                */
-               mv = readl(c->out_port);
-               if (mv == I2O_QUEUE_EMPTY)
-                       mv = readl(c->out_port);
+               rc = IRQ_HANDLED;
        }
 
-       return IRQ_HANDLED;
+       return rc;
 }
 
 /**
index 3414325bdcfdbaecdba30ff2d527b838ed05fd21..90c984ecd521bbd4a18bcd36fabfabf1431159bc 100644 (file)
@@ -32,6 +32,10 @@ typedef unsigned int u32;
 
 #endif                         /* __KERNEL__ */
 
+/*
+ *     Vendors
+ */
+#define I2O_VENDOR_DPT                         0x001b
 
 /*
  * I2O Control IOCTLs and structures
@@ -333,7 +337,7 @@ typedef struct _i2o_status_block {
 #define I2O_CLASS_ATE_PERIPHERAL               0x061
 #define I2O_CLASS_FLOPPY_CONTROLLER            0x070
 #define I2O_CLASS_FLOPPY_DEVICE                0x071
-#define I2O_CLASS_BUS_ADAPTER_PORT             0x080
+#define I2O_CLASS_BUS_ADAPTER                  0x080
 #define I2O_CLASS_PEER_TRANSPORT_AGENT         0x090
 #define I2O_CLASS_PEER_TRANSPORT               0x091
 #define        I2O_CLASS_END                           0xfff
index e8cd1129001034904f43dbca8bbd943d5779d9a1..497ea574f96bf5e773bd79695a0585874e961147 100644 (file)
@@ -157,7 +157,8 @@ struct i2o_controller {
 
        void __iomem *in_port;  /* Inbout port address */
        void __iomem *out_port; /* Outbound port address */
-       void __iomem *irq_mask;         /* Interrupt register address */
+       void __iomem *irq_status;       /* Interrupt status register address */
+       void __iomem *irq_mask; /* Interrupt mask register address */
 
        /* Dynamic LCT related data */
 
@@ -242,15 +243,6 @@ extern int i2o_msg_post_wait_mem(struct i2o_controller *, u32, unsigned long,
 extern void i2o_msg_nop(struct i2o_controller *, u32);
 static inline void i2o_flush_reply(struct i2o_controller *, u32);
 
-/* DMA handling functions */
-static inline int i2o_dma_alloc(struct device *, struct i2o_dma *, size_t,
-                               unsigned int);
-static inline void i2o_dma_free(struct device *, struct i2o_dma *);
-int i2o_dma_realloc(struct device *, struct i2o_dma *, size_t, unsigned int);
-
-static inline int i2o_dma_map(struct device *, struct i2o_dma *);
-static inline void i2o_dma_unmap(struct device *, struct i2o_dma *);
-
 /* IOP functions */
 extern int i2o_status_get(struct i2o_controller *);
 
@@ -275,6 +267,16 @@ static inline u32 i2o_ptr_high(void *ptr)
 {
        return (u32) ((u64) ptr >> 32);
 };
+
+static inline u32 i2o_dma_low(dma_addr_t dma_addr)
+{
+       return (u32) (u64) dma_addr;
+};
+
+static inline u32 i2o_dma_high(dma_addr_t dma_addr)
+{
+       return (u32) ((u64) dma_addr >> 32);
+};
 #else
 static inline u32 i2o_cntxt_list_add(struct i2o_controller *c, void *ptr)
 {
@@ -305,8 +307,246 @@ static inline u32 i2o_ptr_high(void *ptr)
 {
        return 0;
 };
+
+static inline u32 i2o_dma_low(dma_addr_t dma_addr)
+{
+       return (u32) dma_addr;
+};
+
+static inline u32 i2o_dma_high(dma_addr_t dma_addr)
+{
+       return 0;
+};
+#endif
+
+/**
+ *     i2o_sg_tablesize - Calculate the maximum number of elements in a SGL
+ *     @c: I2O controller for which the calculation should be done
+ *     @body_size: maximum body size used for message in 32-bit words.
+ *
+ *     Return the maximum number of SG elements in a SG list.
+ */
+static inline u16 i2o_sg_tablesize(struct i2o_controller *c, u16 body_size)
+{
+       i2o_status_block *sb = c->status_block.virt;
+       u16 sg_count =
+           (sb->inbound_frame_size - sizeof(struct i2o_message) / 4) -
+           body_size;
+
+       if (c->pae_support) {
+               /*
+                * for 64-bit a SG attribute element must be added and each
+                * SG element needs 12 bytes instead of 8.
+                */
+               sg_count -= 2;
+               sg_count /= 3;
+       } else
+               sg_count /= 2;
+
+       if (c->short_req && (sg_count > 8))
+               sg_count = 8;
+
+       return sg_count;
+};
+
+/**
+ *     i2o_dma_map_single - Map pointer to controller and fill in I2O message.
+ *     @c: I2O controller
+ *     @ptr: pointer to the data which should be mapped
+ *     @size: size of data in bytes
+ *     @direction: DMA_TO_DEVICE / DMA_FROM_DEVICE
+ *     @sg_ptr: pointer to the SG list inside the I2O message
+ *
+ *     This function does all necessary DMA handling and also writes the I2O
+ *     SGL elements into the I2O message. For details on DMA handling see also
+ *     dma_map_single(). The pointer sg_ptr will only be set to the end of the
+ *     SG list if the allocation was successful.
+ *
+ *     Returns DMA address which must be checked for failures using
+ *     dma_mapping_error().
+ */
+static inline dma_addr_t i2o_dma_map_single(struct i2o_controller *c, void *ptr,
+                                           size_t size,
+                                           enum dma_data_direction direction,
+                                           u32 __iomem ** sg_ptr)
+{
+       u32 sg_flags;
+       u32 __iomem *mptr = *sg_ptr;
+       dma_addr_t dma_addr;
+
+       switch (direction) {
+       case DMA_TO_DEVICE:
+               sg_flags = 0xd4000000;
+               break;
+       case DMA_FROM_DEVICE:
+               sg_flags = 0xd0000000;
+               break;
+       default:
+               return 0;
+       }
+
+       dma_addr = dma_map_single(&c->pdev->dev, ptr, size, direction);
+       if (!dma_mapping_error(dma_addr)) {
+#ifdef CONFIG_I2O_EXT_ADAPTEC_DMA64
+               if ((sizeof(dma_addr_t) > 4) && c->pae_support) {
+                       writel(0x7C020002, mptr++);
+                       writel(PAGE_SIZE, mptr++);
+               }
+#endif
+
+               writel(sg_flags | size, mptr++);
+               writel(i2o_dma_low(dma_addr), mptr++);
+#ifdef CONFIG_I2O_EXT_ADAPTEC_DMA64
+               if ((sizeof(dma_addr_t) > 4) && c->pae_support)
+                       writel(i2o_dma_high(dma_addr), mptr++);
+#endif
+               *sg_ptr = mptr;
+       }
+       return dma_addr;
+};
+
+/**
+ *     i2o_dma_map_sg - Map a SG List to controller and fill in I2O message.
+ *     @c: I2O controller
+ *     @sg: SG list to be mapped
+ *     @sg_count: number of elements in the SG list
+ *     @direction: DMA_TO_DEVICE / DMA_FROM_DEVICE
+ *     @sg_ptr: pointer to the SG list inside the I2O message
+ *
+ *     This function does all necessary DMA handling and also writes the I2O
+ *     SGL elements into the I2O message. For details on DMA handling see also
+ *     dma_map_sg(). The pointer sg_ptr will only be set to the end of the SG
+ *     list if the allocation was successful.
+ *
+ *     Returns 0 on failure or 1 on success.
+ */
+static inline int i2o_dma_map_sg(struct i2o_controller *c,
+                                struct scatterlist *sg, int sg_count,
+                                enum dma_data_direction direction,
+                                u32 __iomem ** sg_ptr)
+{
+       u32 sg_flags;
+       u32 __iomem *mptr = *sg_ptr;
+
+       switch (direction) {
+       case DMA_TO_DEVICE:
+               sg_flags = 0x14000000;
+               break;
+       case DMA_FROM_DEVICE:
+               sg_flags = 0x10000000;
+               break;
+       default:
+               return 0;
+       }
+
+       sg_count = dma_map_sg(&c->pdev->dev, sg, sg_count, direction);
+       if (!sg_count)
+               return 0;
+
+#ifdef CONFIG_I2O_EXT_ADAPTEC_DMA64
+       if ((sizeof(dma_addr_t) > 4) && c->pae_support) {
+               writel(0x7C020002, mptr++);
+               writel(PAGE_SIZE, mptr++);
+       }
 #endif
 
+       while (sg_count-- > 0) {
+               if (!sg_count)
+                       sg_flags |= 0xC0000000;
+               writel(sg_flags | sg_dma_len(sg), mptr++);
+               writel(i2o_dma_low(sg_dma_address(sg)), mptr++);
+#ifdef CONFIG_I2O_EXT_ADAPTEC_DMA64
+               if ((sizeof(dma_addr_t) > 4) && c->pae_support)
+                       writel(i2o_dma_high(sg_dma_address(sg)), mptr++);
+#endif
+               sg++;
+       }
+       *sg_ptr = mptr;
+
+       return 1;
+};
+
+/**
+ *     i2o_dma_alloc - Allocate DMA memory
+ *     @dev: struct device pointer to the PCI device of the I2O controller
+ *     @addr: i2o_dma struct which should get the DMA buffer
+ *     @len: length of the new DMA memory
+ *     @gfp_mask: GFP mask
+ *
+ *     Allocate a coherent DMA memory and write the pointers into addr.
+ *
+ *     Returns 0 on success or -ENOMEM on failure.
+ */
+static inline int i2o_dma_alloc(struct device *dev, struct i2o_dma *addr,
+                               size_t len, unsigned int gfp_mask)
+{
+       struct pci_dev *pdev = to_pci_dev(dev);
+       int dma_64 = 0;
+
+       if ((sizeof(dma_addr_t) > 4) && (pdev->dma_mask == DMA_64BIT_MASK)) {
+               dma_64 = 1;
+               if (pci_set_dma_mask(pdev, DMA_32BIT_MASK))
+                       return -ENOMEM;
+       }
+
+       addr->virt = dma_alloc_coherent(dev, len, &addr->phys, gfp_mask);
+
+       if ((sizeof(dma_addr_t) > 4) && dma_64)
+               if (pci_set_dma_mask(pdev, DMA_64BIT_MASK))
+                       printk(KERN_WARNING "i2o: unable to set 64-bit DMA");
+
+       if (!addr->virt)
+               return -ENOMEM;
+
+       memset(addr->virt, 0, len);
+       addr->len = len;
+
+       return 0;
+};
+
+/**
+ *     i2o_dma_free - Free DMA memory
+ *     @dev: struct device pointer to the PCI device of the I2O controller
+ *     @addr: i2o_dma struct which contains the DMA buffer
+ *
+ *     Free a coherent DMA memory and set virtual address of addr to NULL.
+ */
+static inline void i2o_dma_free(struct device *dev, struct i2o_dma *addr)
+{
+       if (addr->virt) {
+               if (addr->phys)
+                       dma_free_coherent(dev, addr->len, addr->virt,
+                                         addr->phys);
+               else
+                       kfree(addr->virt);
+               addr->virt = NULL;
+       }
+};
+
+/**
+ *     i2o_dma_realloc - Realloc DMA memory
+ *     @dev: struct device pointer to the PCI device of the I2O controller
+ *     @addr: pointer to a i2o_dma struct DMA buffer
+ *     @len: new length of memory
+ *     @gfp_mask: GFP mask
+ *
+ *     If there was something allocated in the addr, free it first. If len > 0
+ *     than try to allocate it and write the addresses back to the addr
+ *     structure. If len == 0 set the virtual address to NULL.
+ *
+ *     Returns the 0 on success or negative error code on failure.
+ */
+static inline int i2o_dma_realloc(struct device *dev, struct i2o_dma *addr,
+                                 size_t len, unsigned int gfp_mask)
+{
+       i2o_dma_free(dev, addr);
+
+       if (len)
+               return i2o_dma_alloc(dev, addr, len, gfp_mask);
+
+       return 0;
+};
+
 /* I2O driver (OSM) functions */
 extern int i2o_driver_register(struct i2o_driver *);
 extern void i2o_driver_unregister(struct i2o_driver *);
@@ -375,10 +615,11 @@ extern int i2o_device_claim_release(struct i2o_device *);
 /* Exec OSM functions */
 extern int i2o_exec_lct_get(struct i2o_controller *);
 
-/* device / driver conversion functions */
+/* device / driver / kobject conversion functions */
 #define to_i2o_driver(drv) container_of(drv,struct i2o_driver, driver)
 #define to_i2o_device(dev) container_of(dev, struct i2o_device, device)
 #define to_i2o_controller(dev) container_of(dev, struct i2o_controller, device)
+#define kobj_to_i2o_device(kobj) to_i2o_device(container_of(kobj, struct device, kobj))
 
 /**
  *     i2o_msg_get - obtain an I2O message from the IOP
@@ -466,8 +707,10 @@ static inline struct i2o_message __iomem *i2o_msg_out_to_virt(struct
                                                              i2o_controller *c,
                                                              u32 m)
 {
-       BUG_ON(m < c->out_queue.phys
-              || m >= c->out_queue.phys + c->out_queue.len);
+       if (unlikely
+           (m < c->out_queue.phys
+            || m >= c->out_queue.phys + c->out_queue.len))
+               return NULL;
 
        return c->out_queue.virt + (m - c->out_queue.phys);
 };
@@ -532,48 +775,6 @@ static inline void i2o_dma_free(struct device *dev, struct i2o_dma *addr)
        }
 };
 
-/**
- *     i2o_dma_map - Map the memory to DMA
- *     @dev: struct device pointer to the PCI device of the I2O controller
- *     @addr: i2o_dma struct which should be mapped
- *
- *     Map the memory in addr->virt to coherent DMA memory and write the
- *     physical address into addr->phys.
- *
- *     Returns 0 on success or -ENOMEM on failure.
- */
-static inline int i2o_dma_map(struct device *dev, struct i2o_dma *addr)
-{
-       if (!addr->virt)
-               return -EFAULT;
-
-       if (!addr->phys)
-               addr->phys = dma_map_single(dev, addr->virt, addr->len,
-                                           DMA_BIDIRECTIONAL);
-       if (!addr->phys)
-               return -ENOMEM;
-
-       return 0;
-};
-
-/**
- *     i2o_dma_unmap - Unmap the DMA memory
- *     @dev: struct device pointer to the PCI device of the I2O controller
- *     @addr: i2o_dma struct which should be unmapped
- *
- *     Unmap the memory in addr->virt from DMA memory.
- */
-static inline void i2o_dma_unmap(struct device *dev, struct i2o_dma *addr)
-{
-       if (!addr->virt)
-               return;
-
-       if (addr->phys) {
-               dma_unmap_single(dev, addr->phys, addr->len, DMA_BIDIRECTIONAL);
-               addr->phys = 0;
-       }
-};
-
 /*
  *     Endian handling wrapped into the macro - keeps the core code
  *     cleaner.
@@ -725,6 +926,14 @@ extern void i2o_debug_state(struct i2o_controller *c);
 #define I2O_CMD_SCSI_ABORT             0x83
 #define I2O_CMD_SCSI_BUSRESET          0x27
 
+/*
+ * Bus Adapter Class
+ */
+#define I2O_CMD_BUS_ADAPTER_RESET      0x85
+#define I2O_CMD_BUS_RESET              0x87
+#define I2O_CMD_BUS_SCAN               0x89
+#define I2O_CMD_BUS_QUIESCE            0x8b
+
 /*
  * Random Block Storage Class
  */
@@ -948,7 +1157,7 @@ extern void i2o_debug_state(struct i2o_controller *c);
 
 /* request queue sizes */
 #define I2O_MAX_SECTORS                        1024
-#define I2O_MAX_SEGMENTS               128
+#define I2O_MAX_PHYS_SEGMENTS          MAX_PHYS_SEGMENTS
 
 #define I2O_REQ_MEMPOOL_SIZE           32