#include <linux/gpio.h>
#include <linux/spi/spi.h>
-#include <mach/ep93xx_spi.h>
+#include <linux/platform_data/spi-ep93xx.h>
/* this is our GPIO line used for chip select */
#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO9
#include <mach/at91sam9g45_matrix.h>
#include <mach/at91_matrix.h>
#include <mach/at91sam9_smc.h>
-#include <mach/at_hdmac.h>
+#include <linux/platform_data/dma-atmel.h>
#include <mach/atmel-mci.h>
#include <media/atmel-isi.h>
#include <mach/at91sam9rl_matrix.h>
#include <mach/at91_matrix.h>
#include <mach/at91sam9_smc.h>
-#include <mach/at_hdmac.h>
+#include <linux/platform_data/dma-atmel.h>
#include "generic.h"
+++ /dev/null
-/*
- * Header file for the Atmel AHB DMA Controller driver
- *
- * Copyright (C) 2008 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#ifndef AT_HDMAC_H
-#define AT_HDMAC_H
-
-#include <linux/dmaengine.h>
-
-/**
- * struct at_dma_platform_data - Controller configuration parameters
- * @nr_channels: Number of channels supported by hardware (max 8)
- * @cap_mask: dma_capability flags supported by the platform
- */
-struct at_dma_platform_data {
- unsigned int nr_channels;
- dma_cap_mask_t cap_mask;
-};
-
-/**
- * struct at_dma_slave - Controller-specific information about a slave
- * @dma_dev: required DMA master device
- * @cfg: Platform-specific initializer for the CFG register
- */
-struct at_dma_slave {
- struct device *dma_dev;
- u32 cfg;
-};
-
-
-/* Platform-configurable bits in CFG */
-#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */
-#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */
-#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */
-#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */
-#define ATC_SRC_H2SEL_SW (0x0 << 9)
-#define ATC_SRC_H2SEL_HW (0x1 << 9)
-#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */
-#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */
-#define ATC_DST_H2SEL_SW (0x0 << 13)
-#define ATC_DST_H2SEL_HW (0x1 << 13)
-#define ATC_SOD (0x1 << 16) /* Stop On Done */
-#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */
-#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */
-#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */
-#define ATC_LOCK_IF_L_CHUNK (0x0 << 22)
-#define ATC_LOCK_IF_L_BUFFER (0x1 << 22)
-#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */
-#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */
-#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28)
-#define ATC_FIFOCFG_HALFFIFO (0x1 << 28)
-#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28)
-
-
-#endif /* AT_HDMAC_H */
#ifndef __MACH_ATMEL_MCI_H
#define __MACH_ATMEL_MCI_H
-#include <mach/at_hdmac.h>
+#include <linux/platform_data/dma-atmel.h>
/**
* struct mci_dma_data - DMA data for MCI interface
#include <linux/module.h>
#include <linux/time.h>
-#include <mach/aemif.h>
+#include <linux/platform_data/mtd-davinci-aemif.h>
/* Timing value configuration */
#include <mach/cp_intc.h>
#include <mach/mux.h>
-#include <mach/nand.h>
+#include <linux/platform_data/mtd-davinci.h>
#include <mach/da8xx.h>
-#include <mach/usb.h>
-#include <mach/aemif.h>
-#include <mach/spi.h>
+#include <linux/platform_data/usb-davinci.h>
+#include <linux/platform_data/mtd-davinci-aemif.h>
+#include <linux/platform_data/spi-davinci.h>
#define DA830_EVM_PHY_ID ""
/*
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
-#include <mach/nand.h>
+#include <linux/platform_data/mtd-davinci.h>
#include <mach/mux.h>
-#include <mach/aemif.h>
-#include <mach/spi.h>
+#include <linux/platform_data/mtd-davinci-aemif.h>
+#include <linux/platform_data/spi-davinci.h>
#include <media/tvp514x.h>
#include <media/adv7343.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-davinci.h>
#include <mach/serial.h>
-#include <mach/nand.h>
-#include <mach/mmc.h>
-#include <mach/usb.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
#include "davinci.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-davinci.h>
#include <mach/serial.h>
-#include <mach/nand.h>
-#include <mach/mmc.h>
-#include <mach/usb.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
#include "davinci.h"
#include <mach/mux.h>
#include <mach/common.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-davinci.h>
#include <mach/serial.h>
-#include <mach/mmc.h>
-#include <mach/nand.h>
-#include <mach/keyscan.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/keyscan-davinci.h>
#include <media/tvp514x.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-davinci.h>
#include <mach/serial.h>
#include <mach/mux.h>
-#include <mach/nand.h>
-#include <mach/mmc.h>
-#include <mach/usb.h>
-#include <mach/aemif.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
+#include <linux/platform_data/mtd-davinci-aemif.h>
#include "davinci.h"
#include <mach/common.h>
#include <mach/serial.h>
-#include <mach/i2c.h>
-#include <mach/nand.h>
+#include <linux/platform_data/i2c-davinci.h>
+#include <linux/platform_data/mtd-davinci.h>
#include <mach/clock.h>
#include <mach/cdce949.h>
-#include <mach/aemif.h>
+#include <linux/platform_data/mtd-davinci-aemif.h>
#include "davinci.h"
#include "clock.h"
#include <mach/common.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
-#include <mach/nand.h>
+#include <linux/platform_data/mtd-davinci.h>
#include <mach/mux.h>
-#include <mach/spi.h>
+#include <linux/platform_data/spi-davinci.h>
#define MITYOMAPL138_PHY_ID ""
#include <asm/mach/arch.h>
#include <mach/common.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-davinci.h>
#include <mach/serial.h>
#include <mach/mux.h>
-#include <mach/nand.h>
-#include <mach/mmc.h>
-#include <mach/usb.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
#include "davinci.h"
#include <asm/mach/flash.h>
#include <mach/common.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-davinci.h>
#include <mach/serial.h>
#include <mach/mux.h>
-#include <mach/usb.h>
+#include <linux/platform_data/usb-davinci.h>
#include "davinci.h"
#include <linux/spi/spi.h>
#include <mach/asp.h>
-#include <mach/keyscan.h>
+#include <linux/platform_data/keyscan-davinci.h>
#include <mach/hardware.h>
#include <media/davinci/vpfe_capture.h>
#include <linux/io.h>
#include <mach/hardware.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-davinci.h>
#include <mach/irqs.h>
#include <mach/cputype.h>
#include <mach/mux.h>
#include <mach/edma.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-davinci.h>
#include <mach/time.h>
#include "davinci.h"
#include <mach/serial.h>
#include <mach/common.h>
#include <mach/asp.h>
-#include <mach/spi.h>
+#include <linux/platform_data/spi-davinci.h>
#include <mach/gpio-davinci.h>
#include "davinci.h"
#include <mach/serial.h>
#include <mach/common.h>
#include <mach/asp.h>
-#include <mach/keyscan.h>
-#include <mach/spi.h>
+#include <linux/platform_data/keyscan-davinci.h>
+#include <linux/platform_data/spi-davinci.h>
#include <mach/gpio-davinci.h>
#include "davinci.h"
+++ /dev/null
-/*
- * TI DaVinci AEMIF support
- *
- * Copyright 2010 (C) Texas Instruments, Inc. http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-#ifndef _MACH_DAVINCI_AEMIF_H
-#define _MACH_DAVINCI_AEMIF_H
-
-#define NRCSR_OFFSET 0x00
-#define AWCCR_OFFSET 0x04
-#define A1CR_OFFSET 0x10
-
-#define ACR_ASIZE_MASK 0x3
-#define ACR_EW_MASK BIT(30)
-#define ACR_SS_MASK BIT(31)
-
-/* All timings in nanoseconds */
-struct davinci_aemif_timing {
- u8 wsetup;
- u8 wstrobe;
- u8 whold;
-
- u8 rsetup;
- u8 rstrobe;
- u8 rhold;
-
- u8 ta;
-};
-
-int davinci_aemif_setup_timing(struct davinci_aemif_timing *t,
- void __iomem *base, unsigned cs);
-#endif
#include <mach/serial.h>
#include <mach/edma.h>
-#include <mach/i2c.h>
#include <mach/asp.h>
-#include <mach/mmc.h>
-#include <mach/usb.h>
#include <mach/pm.h>
-#include <mach/spi.h>
+#include <linux/platform_data/i2c-davinci.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
+#include <linux/platform_data/spi-davinci.h>
#include <media/davinci/vpif_types.h>
+++ /dev/null
-/*
- * DaVinci I2C controller platform_device info
- *
- * Author: Vladimir Barinov, MontaVista Software, Inc. <source@mvista.com>
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
-*/
-
-#ifndef __ASM_ARCH_I2C_H
-#define __ASM_ARCH_I2C_H
-
-/* All frequencies are expressed in kHz */
-struct davinci_i2c_platform_data {
- unsigned int bus_freq; /* standard bus frequency (kHz) */
- unsigned int bus_delay; /* post-transaction delay (usec) */
- unsigned int sda_pin; /* GPIO pin ID to use for SDA */
- unsigned int scl_pin; /* GPIO pin ID to use for SCL */
-};
-
-/* for board setup code */
-void davinci_init_i2c(struct davinci_i2c_platform_data *);
-
-#endif /* __ASM_ARCH_I2C_H */
+++ /dev/null
-/*
- * Copyright (C) 2009 Texas Instruments, Inc
- *
- * Author: Miguel Aguilar <miguel.aguilar@ridgerun.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#ifndef DAVINCI_KEYSCAN_H
-#define DAVINCI_KEYSCAN_H
-
-#include <linux/io.h>
-
-enum davinci_matrix_types {
- DAVINCI_KEYSCAN_MATRIX_4X4,
- DAVINCI_KEYSCAN_MATRIX_5X3,
-};
-
-struct davinci_ks_platform_data {
- int (*device_enable)(struct device *dev);
- unsigned short *keymap;
- u32 keymapsize;
- u8 rep:1;
- u8 strobe;
- u8 interval;
- u8 matrix_type;
-};
-
-#endif
-
+++ /dev/null
-/*
- * Board-specific MMC configuration
- */
-
-#ifndef _DAVINCI_MMC_H
-#define _DAVINCI_MMC_H
-
-#include <linux/types.h>
-#include <linux/mmc/host.h>
-
-struct davinci_mmc_config {
- /* get_cd()/get_wp() may sleep */
- int (*get_cd)(int module);
- int (*get_ro)(int module);
-
- void (*set_power)(int module, bool on);
-
- /* wires == 0 is equivalent to wires == 4 (4-bit parallel) */
- u8 wires;
-
- u32 max_freq;
-
- /* any additional host capabilities: OR'd in to mmc->f_caps */
- u32 caps;
-
- /* Version of the MMC/SD controller */
- u8 version;
-
- /* Number of sg segments */
- u8 nr_sg;
-};
-void davinci_setup_mmc(int module, struct davinci_mmc_config *config);
-
-enum {
- MMC_CTLR_VERSION_1 = 0, /* DM644x and DM355 */
- MMC_CTLR_VERSION_2, /* DA830 */
-};
-
-#endif
+++ /dev/null
-/*
- * mach-davinci/nand.h
- *
- * Copyright © 2006 Texas Instruments.
- *
- * Ported to 2.6.23 Copyright © 2008 by
- * Sander Huijsen <Shuijsen@optelecom-nkf.com>
- * Troy Kisky <troy.kisky@boundarydevices.com>
- * Dirk Behme <Dirk.Behme@gmail.com>
- *
- * --------------------------------------------------------------------------
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef __ARCH_ARM_DAVINCI_NAND_H
-#define __ARCH_ARM_DAVINCI_NAND_H
-
-#include <linux/mtd/nand.h>
-
-#define NANDFCR_OFFSET 0x60
-#define NANDFSR_OFFSET 0x64
-#define NANDF1ECC_OFFSET 0x70
-
-/* 4-bit ECC syndrome registers */
-#define NAND_4BIT_ECC_LOAD_OFFSET 0xbc
-#define NAND_4BIT_ECC1_OFFSET 0xc0
-#define NAND_4BIT_ECC2_OFFSET 0xc4
-#define NAND_4BIT_ECC3_OFFSET 0xc8
-#define NAND_4BIT_ECC4_OFFSET 0xcc
-#define NAND_ERR_ADD1_OFFSET 0xd0
-#define NAND_ERR_ADD2_OFFSET 0xd4
-#define NAND_ERR_ERRVAL1_OFFSET 0xd8
-#define NAND_ERR_ERRVAL2_OFFSET 0xdc
-
-/* NOTE: boards don't need to use these address bits
- * for ALE/CLE unless they support booting from NAND.
- * They're used unless platform data overrides them.
- */
-#define MASK_ALE 0x08
-#define MASK_CLE 0x10
-
-struct davinci_nand_pdata { /* platform_data */
- uint32_t mask_ale;
- uint32_t mask_cle;
-
- /* for packages using two chipselects */
- uint32_t mask_chipsel;
-
- /* board's default static partition info */
- struct mtd_partition *parts;
- unsigned nr_parts;
-
- /* none == NAND_ECC_NONE (strongly *not* advised!!)
- * soft == NAND_ECC_SOFT
- * else == NAND_ECC_HW, according to ecc_bits
- *
- * All DaVinci-family chips support 1-bit hardware ECC.
- * Newer ones also support 4-bit ECC, but are awkward
- * using it with large page chips.
- */
- nand_ecc_modes_t ecc_mode;
- u8 ecc_bits;
-
- /* e.g. NAND_BUSWIDTH_16 */
- unsigned options;
- /* e.g. NAND_BBT_USE_FLASH */
- unsigned bbt_options;
-
- /* Main and mirror bbt descriptor overrides */
- struct nand_bbt_descr *bbt_td;
- struct nand_bbt_descr *bbt_md;
-
- /* Access timings */
- struct davinci_aemif_timing *timing;
-};
-
-#endif /* __ARCH_ARM_DAVINCI_NAND_H */
+++ /dev/null
-/*
- * Copyright 2009 Texas Instruments.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef __ARCH_ARM_DAVINCI_SPI_H
-#define __ARCH_ARM_DAVINCI_SPI_H
-
-#include <mach/edma.h>
-
-#define SPI_INTERN_CS 0xFF
-
-enum {
- SPI_VERSION_1, /* For DM355/DM365/DM6467 */
- SPI_VERSION_2, /* For DA8xx */
-};
-
-/**
- * davinci_spi_platform_data - Platform data for SPI master device on DaVinci
- *
- * @version: version of the SPI IP. Different DaVinci devices have slightly
- * varying versions of the same IP.
- * @num_chipselect: number of chipselects supported by this SPI master
- * @intr_line: interrupt line used to connect the SPI IP to the ARM interrupt
- * controller withn the SoC. Possible values are 0 and 1.
- * @chip_sel: list of GPIOs which can act as chip-selects for the SPI.
- * SPI_INTERN_CS denotes internal SPI chip-select. Not necessary
- * to populate if all chip-selects are internal.
- * @cshold_bug: set this to true if the SPI controller on your chip requires
- * a write to CSHOLD bit in between transfers (like in DM355).
- * @dma_event_q: DMA event queue to use if SPI_IO_TYPE_DMA is used for any
- * device on the bus.
- */
-struct davinci_spi_platform_data {
- u8 version;
- u8 num_chipselect;
- u8 intr_line;
- u8 *chip_sel;
- bool cshold_bug;
- enum dma_event_q dma_event_q;
-};
-
-/**
- * davinci_spi_config - Per-chip-select configuration for SPI slave devices
- *
- * @wdelay: amount of delay between transmissions. Measured in number of
- * SPI module clocks.
- * @odd_parity: polarity of parity flag at the end of transmit data stream.
- * 0 - odd parity, 1 - even parity.
- * @parity_enable: enable transmission of parity at end of each transmit
- * data stream.
- * @io_type: type of IO transfer. Choose between polled, interrupt and DMA.
- * @timer_disable: disable chip-select timers (setup and hold)
- * @c2tdelay: chip-select setup time. Measured in number of SPI module clocks.
- * @t2cdelay: chip-select hold time. Measured in number of SPI module clocks.
- * @t2edelay: transmit data finished to SPI ENAn pin inactive time. Measured
- * in number of SPI clocks.
- * @c2edelay: chip-select active to SPI ENAn signal active time. Measured in
- * number of SPI clocks.
- */
-struct davinci_spi_config {
- u8 wdelay;
- u8 odd_parity;
- u8 parity_enable;
-#define SPI_IO_TYPE_INTR 0
-#define SPI_IO_TYPE_POLL 1
-#define SPI_IO_TYPE_DMA 2
- u8 io_type;
- u8 timer_disable;
- u8 c2tdelay;
- u8 t2cdelay;
- u8 t2edelay;
- u8 c2edelay;
-};
-
-#endif /* __ARCH_ARM_DAVINCI_SPI_H */
#include <linux/input/matrix_keypad.h>
#include <linux/mfd/ti_ssp.h>
-#include <mach/mmc.h>
-#include <mach/nand.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/mtd-davinci.h>
#include <mach/serial.h>
struct tnetv107x_device_info {
+++ /dev/null
-/*
- * USB related definitions
- *
- * Copyright (C) 2009 MontaVista Software, Inc. <source@mvista.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_USB_H
-#define __ASM_ARCH_USB_H
-
-/* DA8xx CFGCHIP2 (USB 2.0 PHY Control) register bits */
-#define CFGCHIP2_PHYCLKGD (1 << 17)
-#define CFGCHIP2_VBUSSENSE (1 << 16)
-#define CFGCHIP2_RESET (1 << 15)
-#define CFGCHIP2_OTGMODE (3 << 13)
-#define CFGCHIP2_NO_OVERRIDE (0 << 13)
-#define CFGCHIP2_FORCE_HOST (1 << 13)
-#define CFGCHIP2_FORCE_DEVICE (2 << 13)
-#define CFGCHIP2_FORCE_HOST_VBUS_LOW (3 << 13)
-#define CFGCHIP2_USB1PHYCLKMUX (1 << 12)
-#define CFGCHIP2_USB2PHYCLKMUX (1 << 11)
-#define CFGCHIP2_PHYPWRDN (1 << 10)
-#define CFGCHIP2_OTGPWRDN (1 << 9)
-#define CFGCHIP2_DATPOL (1 << 8)
-#define CFGCHIP2_USB1SUSPENDM (1 << 7)
-#define CFGCHIP2_PHY_PLLON (1 << 6) /* override PLL suspend */
-#define CFGCHIP2_SESENDEN (1 << 5) /* Vsess_end comparator */
-#define CFGCHIP2_VBDTCTEN (1 << 4) /* Vbus comparator */
-#define CFGCHIP2_REFFREQ (0xf << 0)
-#define CFGCHIP2_REFFREQ_12MHZ (1 << 0)
-#define CFGCHIP2_REFFREQ_24MHZ (2 << 0)
-#define CFGCHIP2_REFFREQ_48MHZ (3 << 0)
-
-struct da8xx_ohci_root_hub;
-
-typedef void (*da8xx_ocic_handler_t)(struct da8xx_ohci_root_hub *hub,
- unsigned port);
-
-/* Passed as the platform data to the OHCI driver */
-struct da8xx_ohci_root_hub {
- /* Switch the port power on/off */
- int (*set_power)(unsigned port, int on);
- /* Read the port power status */
- int (*get_power)(unsigned port);
- /* Read the port over-current indicator */
- int (*get_oci)(unsigned port);
- /* Over-current indicator change notification (pass NULL to disable) */
- int (*ocic_notify)(da8xx_ocic_handler_t handler);
-
- /* Time from power on to power good (in 2 ms units) */
- u8 potpgt;
-};
-
-void davinci_setup_usb(unsigned mA, unsigned potpgt_ms);
-
-#endif /* ifndef __ASM_ARCH_USB_H */
#include <mach/common.h>
#include <mach/irqs.h>
#include <mach/cputype.h>
-#include <mach/usb.h>
+#include <linux/platform_data/usb-davinci.h>
#define DAVINCI_USB_OTG_BASE 0x01c64000
#include <asm/mach/arch.h>
#include <linux/irq.h>
#include <plat/time.h>
-#include <plat/ehci-orion.h>
+#include <linux/platform_data/usb-ehci-orion.h>
#include <plat/common.h>
#include <plat/addr-map.h>
#include "common.h"
#include <linux/export.h>
#include <mach/hardware.h>
-#include <mach/fb.h>
-#include <mach/ep93xx_keypad.h>
-#include <mach/ep93xx_spi.h>
+#include <linux/platform_data/video-ep93xx.h>
+#include <linux/platform_data/keypad-ep93xx.h>
+#include <linux/platform_data/spi-ep93xx.h>
#include <mach/gpio-ep93xx.h>
#include <asm/mach/map.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-ep93xx.h>
#include <mach/hardware.h>
#include "soc.h"
#include <sound/cs4271.h>
#include <mach/hardware.h>
-#include <mach/fb.h>
-#include <mach/ep93xx_spi.h>
+#include <linux/platform_data/video-ep93xx.h>
+#include <linux/platform_data/spi-ep93xx.h>
#include <mach/gpio-ep93xx.h>
#include <asm/hardware/vic.h>
+++ /dev/null
-#ifndef __ASM_ARCH_DMA_H
-#define __ASM_ARCH_DMA_H
-
-#include <linux/types.h>
-#include <linux/dmaengine.h>
-#include <linux/dma-mapping.h>
-
-/*
- * M2P channels.
- *
- * Note that these values are also directly used for setting the PPALLOC
- * register.
- */
-#define EP93XX_DMA_I2S1 0
-#define EP93XX_DMA_I2S2 1
-#define EP93XX_DMA_AAC1 2
-#define EP93XX_DMA_AAC2 3
-#define EP93XX_DMA_AAC3 4
-#define EP93XX_DMA_I2S3 5
-#define EP93XX_DMA_UART1 6
-#define EP93XX_DMA_UART2 7
-#define EP93XX_DMA_UART3 8
-#define EP93XX_DMA_IRDA 9
-/* M2M channels */
-#define EP93XX_DMA_SSP 10
-#define EP93XX_DMA_IDE 11
-
-/**
- * struct ep93xx_dma_data - configuration data for the EP93xx dmaengine
- * @port: peripheral which is requesting the channel
- * @direction: TX/RX channel
- * @name: optional name for the channel, this is displayed in /proc/interrupts
- *
- * This information is passed as private channel parameter in a filter
- * function. Note that this is only needed for slave/cyclic channels. For
- * memcpy channels %NULL data should be passed.
- */
-struct ep93xx_dma_data {
- int port;
- enum dma_transfer_direction direction;
- const char *name;
-};
-
-/**
- * struct ep93xx_dma_chan_data - platform specific data for a DMA channel
- * @name: name of the channel, used for getting the right clock for the channel
- * @base: mapped registers
- * @irq: interrupt number used by this channel
- */
-struct ep93xx_dma_chan_data {
- const char *name;
- void __iomem *base;
- int irq;
-};
-
-/**
- * struct ep93xx_dma_platform_data - platform data for the dmaengine driver
- * @channels: array of channels which are passed to the driver
- * @num_channels: number of channels in the array
- *
- * This structure is passed to the DMA engine driver via platform data. For
- * M2P channels, contract is that even channels are for TX and odd for RX.
- * There is no requirement for the M2M channels.
- */
-struct ep93xx_dma_platform_data {
- struct ep93xx_dma_chan_data *channels;
- size_t num_channels;
-};
-
-static inline bool ep93xx_dma_chan_is_m2p(struct dma_chan *chan)
-{
- return !strcmp(dev_name(chan->device->dev), "ep93xx-dma-m2p");
-}
-
-/**
- * ep93xx_dma_chan_direction - returns direction the channel can be used
- * @chan: channel
- *
- * This function can be used in filter functions to find out whether the
- * channel supports given DMA direction. Only M2P channels have such
- * limitation, for M2M channels the direction is configurable.
- */
-static inline enum dma_transfer_direction
-ep93xx_dma_chan_direction(struct dma_chan *chan)
-{
- if (!ep93xx_dma_chan_is_m2p(chan))
- return DMA_NONE;
-
- /* even channels are for TX, odd for RX */
- return (chan->chan_id % 2 == 0) ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM;
-}
-
-#endif /* __ASM_ARCH_DMA_H */
+++ /dev/null
-/*
- * arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h
- */
-
-#ifndef __ASM_ARCH_EP93XX_KEYPAD_H
-#define __ASM_ARCH_EP93XX_KEYPAD_H
-
-struct matrix_keymap_data;
-
-/* flags for the ep93xx_keypad driver */
-#define EP93XX_KEYPAD_DISABLE_3_KEY (1<<0) /* disable 3-key reset */
-#define EP93XX_KEYPAD_DIAG_MODE (1<<1) /* diagnostic mode */
-#define EP93XX_KEYPAD_BACK_DRIVE (1<<2) /* back driving mode */
-#define EP93XX_KEYPAD_TEST_MODE (1<<3) /* scan only column 0 */
-#define EP93XX_KEYPAD_KDIV (1<<4) /* 1/4 clock or 1/16 clock */
-#define EP93XX_KEYPAD_AUTOREPEAT (1<<5) /* enable key autorepeat */
-
-/**
- * struct ep93xx_keypad_platform_data - platform specific device structure
- * @keymap_data: pointer to &matrix_keymap_data
- * @debounce: debounce start count; terminal count is 0xff
- * @prescale: row/column counter pre-scaler load value
- * @flags: see above
- */
-struct ep93xx_keypad_platform_data {
- struct matrix_keymap_data *keymap_data;
- unsigned int debounce;
- unsigned int prescale;
- unsigned int flags;
-};
-
-#define EP93XX_MATRIX_ROWS (8)
-#define EP93XX_MATRIX_COLS (8)
-
-#endif /* __ASM_ARCH_EP93XX_KEYPAD_H */
+++ /dev/null
-#ifndef __ASM_MACH_EP93XX_SPI_H
-#define __ASM_MACH_EP93XX_SPI_H
-
-struct spi_device;
-
-/**
- * struct ep93xx_spi_info - EP93xx specific SPI descriptor
- * @num_chipselect: number of chip selects on this board, must be
- * at least one
- * @use_dma: use DMA for the transfers
- */
-struct ep93xx_spi_info {
- int num_chipselect;
- bool use_dma;
-};
-
-/**
- * struct ep93xx_spi_chip_ops - operation callbacks for SPI slave device
- * @setup: setup the chip select mechanism
- * @cleanup: cleanup the chip select mechanism
- * @cs_control: control the device chip select
- */
-struct ep93xx_spi_chip_ops {
- int (*setup)(struct spi_device *spi);
- void (*cleanup)(struct spi_device *spi);
- void (*cs_control)(struct spi_device *spi, int value);
-};
-
-#endif /* __ASM_MACH_EP93XX_SPI_H */
+++ /dev/null
-/*
- * arch/arm/mach-ep93xx/include/mach/fb.h
- */
-
-#ifndef __ASM_ARCH_EP93XXFB_H
-#define __ASM_ARCH_EP93XXFB_H
-
-struct platform_device;
-struct fb_videomode;
-struct fb_info;
-
-#define EP93XXFB_USE_MODEDB 0
-
-/* VideoAttributes flags */
-#define EP93XXFB_STATE_MACHINE_ENABLE (1 << 0)
-#define EP93XXFB_PIXEL_CLOCK_ENABLE (1 << 1)
-#define EP93XXFB_VSYNC_ENABLE (1 << 2)
-#define EP93XXFB_PIXEL_DATA_ENABLE (1 << 3)
-#define EP93XXFB_COMPOSITE_SYNC (1 << 4)
-#define EP93XXFB_SYNC_VERT_HIGH (1 << 5)
-#define EP93XXFB_SYNC_HORIZ_HIGH (1 << 6)
-#define EP93XXFB_SYNC_BLANK_HIGH (1 << 7)
-#define EP93XXFB_PCLK_FALLING (1 << 8)
-#define EP93XXFB_ENABLE_AC (1 << 9)
-#define EP93XXFB_ENABLE_LCD (1 << 10)
-#define EP93XXFB_ENABLE_CCIR (1 << 12)
-#define EP93XXFB_USE_PARALLEL_INTERFACE (1 << 13)
-#define EP93XXFB_ENABLE_INTERRUPT (1 << 14)
-#define EP93XXFB_USB_INTERLACE (1 << 16)
-#define EP93XXFB_USE_EQUALIZATION (1 << 17)
-#define EP93XXFB_USE_DOUBLE_HORZ (1 << 18)
-#define EP93XXFB_USE_DOUBLE_VERT (1 << 19)
-#define EP93XXFB_USE_BLANK_PIXEL (1 << 20)
-#define EP93XXFB_USE_SDCSN0 (0 << 21)
-#define EP93XXFB_USE_SDCSN1 (1 << 21)
-#define EP93XXFB_USE_SDCSN2 (2 << 21)
-#define EP93XXFB_USE_SDCSN3 (3 << 21)
-
-#define EP93XXFB_ENABLE (EP93XXFB_STATE_MACHINE_ENABLE | \
- EP93XXFB_PIXEL_CLOCK_ENABLE | \
- EP93XXFB_VSYNC_ENABLE | \
- EP93XXFB_PIXEL_DATA_ENABLE)
-
-struct ep93xxfb_mach_info {
- unsigned int num_modes;
- const struct fb_videomode *modes;
- const struct fb_videomode *default_mode;
- int bpp;
- unsigned int flags;
-
- int (*setup)(struct platform_device *pdev);
- void (*teardown)(struct platform_device *pdev);
- void (*blank)(int blank_mode, struct fb_info *info);
-};
-
-#endif /* __ASM_ARCH_EP93XXFB_H */
#include <linux/i2c-gpio.h>
#include <mach/hardware.h>
-#include <mach/fb.h>
+#include <linux/platform_data/video-ep93xx.h>
#include <mach/gpio-ep93xx.h>
#include <asm/hardware/vic.h>
#include <linux/mtd/nand.h>
#include <mach/hardware.h>
-#include <mach/fb.h>
+#include <linux/platform_data/video-ep93xx.h>
#include <mach/gpio-ep93xx.h>
#include <asm/hardware/vic.h>
#include <linux/mmc/host.h>
#include <mach/hardware.h>
-#include <mach/fb.h>
-#include <mach/ep93xx_spi.h>
+#include <linux/platform_data/video-ep93xx.h>
+#include <linux/platform_data/spi-ep93xx.h>
#include <mach/gpio-ep93xx.h>
#include <asm/hardware/vic.h>
#include <linux/gpio.h>
#include <plat/gpio-cfg.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-s3c.h>
#include <mach/map.h>
#include <mach/dma.h>
#include <mach/irqs.h>
#include <mach/map.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/usb-exynos.h>
#include <plat/devs.h>
#include <plat/usb-phy.h>
+++ /dev/null
-/*
- * Copyright (C) 2011 Samsung Electronics Co.Ltd
- * http://www.samsung.com/
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef __MACH_EXYNOS_OHCI_H
-#define __MACH_EXYNOS_OHCI_H
-
-struct exynos4_ohci_platdata {
- int (*phy_init)(struct platform_device *pdev, int type);
- int (*phy_exit)(struct platform_device *pdev, int type);
-};
-
-extern void exynos4_ohci_set_platdata(struct exynos4_ohci_platdata *pd);
-
-#endif /* __MACH_EXYNOS_OHCI_H */
#include <plat/devs.h>
#include <plat/fb.h>
#include <plat/sdhci.h>
-#include <plat/ehci.h>
+#include <linux/platform_data/usb-ehci-s5p.h>
#include <plat/clock.h>
#include <plat/gpio-cfg.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/mfc.h>
#include <plat/fimc-core.h>
#include <plat/camport.h>
-#include <plat/mipi_csis.h>
+#include <linux/platform_data/mipi-csis.h>
#include <mach/map.h>
#include <plat/cpu.h>
#include <plat/devs.h>
#include <plat/sdhci.h>
-#include <plat/iic.h>
-#include <plat/ehci.h>
+#include <linux/platform_data/i2c-s3c2410.h>
+#include <linux/platform_data/usb-ehci-s5p.h>
#include <plat/clock.h>
#include <plat/gpio-cfg.h>
#include <plat/backlight.h>
#include <plat/mfc.h>
#include <plat/hdmi.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/usb-exynos.h>
#include <mach/map.h>
#include <drm/exynos_drm.h>
#include <plat/devs.h>
#include <plat/fb.h>
#include <plat/gpio-cfg.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/keypad.h>
#include <plat/mfc.h>
#include <plat/regs-fb.h>
#include <plat/fb.h>
#include <plat/keypad.h>
#include <plat/sdhci.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
#include <plat/backlight.h>
#include <plat/mfc.h>
-#include <plat/ehci.h>
+#include <linux/platform_data/usb-ehci-s5p.h>
#include <plat/clock.h>
#include <plat/hdmi.h>
#include <mach/map.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/usb-exynos.h>
#include <drm/exynos_drm.h>
#include "common.h"
#include <plat/clock.h>
#include <plat/cpu.h>
#include <plat/devs.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
#include <plat/fb.h>
#include <plat/mfc.h>
#include <plat/fimc-core.h>
#include <plat/s5p-time.h>
#include <plat/camport.h>
-#include <plat/mipi_csis.h>
+#include <linux/platform_data/mipi-csis.h>
#include <mach/map.h>
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
#include <plat/cpu.h>
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c1_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c2_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c3_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c4_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c5_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c6_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c7_cfg_gpio(struct platform_device *dev)
#include <linux/io.h>
#include <mach/hardware.h>
-#include <mach/mxc_ehci.h>
+#include <linux/platform_data/usb-ehci-mxc.h>
#define USBCTRL_OTGBASE_OFFSET 0x600
#include <linux/io.h>
#include <mach/hardware.h>
-#include <mach/mxc_ehci.h>
+#include <linux/platform_data/usb-ehci-mxc.h>
#define USBCTRL_OTGBASE_OFFSET 0x600
#include <linux/io.h>
#include <mach/hardware.h>
-#include <mach/mxc_ehci.h>
+#include <linux/platform_data/usb-ehci-mxc.h>
#define USBCTRL_OTGBASE_OFFSET 0x600
#include <linux/io.h>
#include <mach/hardware.h>
-#include <mach/mxc_ehci.h>
+#include <linux/platform_data/usb-ehci-mxc.h>
#define USBCTRL_OTGBASE_OFFSET 0x600
#include <linux/io.h>
#include <mach/hardware.h>
-#include <mach/mxc_ehci.h>
+#include <linux/platform_data/usb-ehci-mxc.h>
#define MXC_OTG_OFFSET 0
#define MXC_H1_OFFSET 0x200
#include <mach/hardware.h>
#include <mach/iomux-mx3.h>
#include <mach/ulpi.h>
-#include <mach/ssi.h>
+#include <linux/platform_data/asoc-imx-ssi.h>
#include "devices-imx31.h"
#include <linux/platform_device.h>
#include <linux/module.h>
-#include <mach/mx1_camera.h>
+#include <linux/platform_data/camera-mx1.h>
/* IMX camera FIQ handler */
EXPORT_SYMBOL(mx1_camera_sof_fiq_start);
#include <asm/mach/map.h>
#include <mach/kirkwood.h>
#include <mach/bridge-regs.h>
-#include <plat/mvsdio.h>
+#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
#include "mpp.h"
#include <asm/mach/map.h>
#include <mach/kirkwood.h>
#include <mach/bridge-regs.h>
-#include <plat/mvsdio.h>
+#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
#include "mpp.h"
#include <asm/mach/time.h>
#include <mach/kirkwood.h>
#include <mach/bridge-regs.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-kirkwood.h>
#include <plat/cache-feroceon-l2.h>
-#include <plat/mvsdio.h>
-#include <plat/orion_nand.h>
-#include <plat/ehci-orion.h>
+#include <linux/platform_data/mmc-mvsdio.h>
+#include <linux/platform_data/mtd-orion_nand.h>
+#include <linux/platform_data/usb-ehci-orion.h>
#include <plat/common.h>
#include <plat/time.h>
#include <plat/addr-map.h>
-#include <plat/mv_xor.h>
+#include <linux/platform_data/dma-mv_xor.h>
#include "common.h"
/*****************************************************************************
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
-#include <mach/leds-ns2.h>
+#include <linux/platform_data/leds-kirkwood-ns2.h>
#include "common.h"
#include "mpp.h"
#include "lacie_v2-common.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
-#include <plat/mvsdio.h>
+#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
#include "mpp.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
-#include <plat/mvsdio.h>
+#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
#include "mpp.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
-#include <plat/mvsdio.h>
+#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
#include "mpp.h"
+++ /dev/null
-/*
- * arch/arm/mach-kirkwood/include/mach/leds-netxbig.h
- *
- * Platform data structure for netxbig LED driver
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_LEDS_NETXBIG_H
-#define __MACH_LEDS_NETXBIG_H
-
-struct netxbig_gpio_ext {
- unsigned *addr;
- int num_addr;
- unsigned *data;
- int num_data;
- unsigned enable;
-};
-
-enum netxbig_led_mode {
- NETXBIG_LED_OFF,
- NETXBIG_LED_ON,
- NETXBIG_LED_SATA,
- NETXBIG_LED_TIMER1,
- NETXBIG_LED_TIMER2,
- NETXBIG_LED_MODE_NUM,
-};
-
-#define NETXBIG_LED_INVALID_MODE NETXBIG_LED_MODE_NUM
-
-struct netxbig_led_timer {
- unsigned long delay_on;
- unsigned long delay_off;
- enum netxbig_led_mode mode;
-};
-
-struct netxbig_led {
- const char *name;
- const char *default_trigger;
- int mode_addr;
- int *mode_val;
- int bright_addr;
-};
-
-struct netxbig_led_platform_data {
- struct netxbig_gpio_ext *gpio_ext;
- struct netxbig_led_timer *timer;
- int num_timer;
- struct netxbig_led *leds;
- int num_leds;
-};
-
-#endif /* __MACH_LEDS_NETXBIG_H */
+++ /dev/null
-/*
- * arch/arm/mach-kirkwood/include/mach/leds-ns2.h
- *
- * Platform data structure for Network Space v2 LED driver
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_LEDS_NS2_H
-#define __MACH_LEDS_NS2_H
-
-struct ns2_led {
- const char *name;
- const char *default_trigger;
- unsigned cmd;
- unsigned slow;
-};
-
-struct ns2_led_platform_data {
- int num_leds;
- struct ns2_led *leds;
-};
-
-#endif /* __MACH_LEDS_NS2_H */
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
-#include <mach/leds-ns2.h>
+#include <linux/platform_data/leds-kirkwood-ns2.h>
#include "common.h"
#include "mpp.h"
#include "lacie_v2-common.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
-#include <mach/leds-netxbig.h>
+#include <linux/platform_data/leds-kirkwood-netxbig.h>
#include "common.h"
#include "mpp.h"
#include "lacie_v2-common.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
-#include <plat/mvsdio.h>
+#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
#include "mpp.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
-#include <plat/mvsdio.h>
+#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
#include "mpp.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
-#include <plat/mvsdio.h>
+#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
#include "mpp.h"
#include <mach/irqs.h>
#include <video/pxa168fb.h>
#include <linux/input.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include "common.h"
#include <linux/i2c.h>
#include <linux/i2c/pxa-i2c.h>
#include <mach/devices.h>
-#include <mach/sram.h>
+#include <linux/platform_data/dma-mmp_tdma.h>
extern struct pxa_device_desc mmp2_device_uart1;
extern struct pxa_device_desc mmp2_device_uart2;
#include <linux/i2c.h>
#include <linux/i2c/pxa-i2c.h>
#include <mach/devices.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
#include <video/pxa168fb.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include <mach/cputype.h>
#include <linux/pxa168_eth.h>
#include <linux/platform_data/mv_usb.h>
#include <linux/i2c.h>
#include <linux/i2c/pxa-i2c.h>
#include <mach/devices.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
extern struct pxa_device_desc pxa910_device_uart1;
extern struct pxa_device_desc pxa910_device_uart2;
+++ /dev/null
-/*
- * linux/arch/arm/mach-mmp/include/mach/sram.h
- *
- * SRAM Memory Management
- *
- * Copyright (c) 2011 Marvell Semiconductors Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#ifndef __ASM_ARCH_SRAM_H
-#define __ASM_ARCH_SRAM_H
-
-#include <linux/genalloc.h>
-
-/* ARBITRARY: SRAM allocations are multiples of this 2^N size */
-#define SRAM_GRANULARITY 512
-
-enum sram_type {
- MMP_SRAM_UNDEFINED = 0,
- MMP_ASRAM,
- MMP_ISRAM,
-};
-
-struct sram_platdata {
- char *pool_name;
- int granularity;
-};
-
-extern struct gen_pool *sram_get_gpool(char *pool_name);
-
-#endif /* __ASM_ARCH_SRAM_H */
#include <linux/slab.h>
#include <linux/genalloc.h>
-#include <mach/sram.h>
+#include <linux/platform_data/dma-mmp_tdma.h>
struct sram_bank_info {
char *pool_name;
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/input.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include <linux/i2c.h>
#include <asm/mach-types.h>
#include <mach/irqs.h>
#include <mach/sirc.h>
#include <mach/vreg.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-msm_sdcc.h>
#include "devices.h"
#include <mach/vreg.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-msm_sdcc.h>
#include "devices.h"
#include <asm/mach-types.h>
#include <asm/system_info.h>
-#include <mach/msm_fb.h>
+#include <linux/platform_data/video-msm_fb.h>
#include <mach/vreg.h>
#include "board-trout.h"
#include "clock.h"
#include "clock-pcom.h"
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-msm_sdcc.h>
static struct resource resources_uart1[] = {
{
#include "clock-pcom.h"
#include "clock-7x30.h"
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-msm_sdcc.h>
static struct resource resources_uart2[] = {
{
#include <asm/mach/flash.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-msm_sdcc.h>
#include "clock-pcom.h"
static struct resource resources_uart3[] = {
#define __ASM_ARCH_MSM_BOARD_H
#include <linux/types.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-msm_sdcc.h>
/* platform device data structures */
+++ /dev/null
-/*
- * arch/arm/include/asm/mach/mmc.h
- */
-#ifndef ASMARM_MACH_MMC_H
-#define ASMARM_MACH_MMC_H
-
-#include <linux/mmc/host.h>
-#include <linux/mmc/card.h>
-#include <linux/mmc/sdio_func.h>
-
-struct msm_mmc_gpio {
- unsigned no;
- const char *name;
-};
-
-struct msm_mmc_gpio_data {
- struct msm_mmc_gpio *gpio;
- u8 size;
-};
-
-struct msm_mmc_platform_data {
- unsigned int ocr_mask; /* available voltages */
- u32 (*translate_vdd)(struct device *, unsigned int);
- unsigned int (*status)(struct device *);
- int (*register_status_notify)(void (*callback)(int card_present, void *dev_id), void *dev_id);
- struct msm_mmc_gpio_data *gpio_data;
- void (*init_card)(struct mmc_card *card);
-};
-
-#endif
+++ /dev/null
-/* arch/arm/mach-msm/include/mach/msm_fb.h
- *
- * Internal shared definitions for various MSM framebuffer parts.
- *
- * Copyright (C) 2007 Google Incorporated
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef _MSM_FB_H_
-#define _MSM_FB_H_
-
-#include <linux/device.h>
-
-struct mddi_info;
-
-struct msm_fb_data {
- int xres; /* x resolution in pixels */
- int yres; /* y resolution in pixels */
- int width; /* disply width in mm */
- int height; /* display height in mm */
- unsigned output_format;
-};
-
-struct msmfb_callback {
- void (*func)(struct msmfb_callback *);
-};
-
-enum {
- MSM_MDDI_PMDH_INTERFACE,
- MSM_MDDI_EMDH_INTERFACE,
- MSM_EBI2_INTERFACE,
-};
-
-#define MSMFB_CAP_PARTIAL_UPDATES (1 << 0)
-
-struct msm_panel_data {
- /* turns off the fb memory */
- int (*suspend)(struct msm_panel_data *);
- /* turns on the fb memory */
- int (*resume)(struct msm_panel_data *);
- /* turns off the panel */
- int (*blank)(struct msm_panel_data *);
- /* turns on the panel */
- int (*unblank)(struct msm_panel_data *);
- void (*wait_vsync)(struct msm_panel_data *);
- void (*request_vsync)(struct msm_panel_data *, struct msmfb_callback *);
- void (*clear_vsync)(struct msm_panel_data *);
- /* from the enum above */
- unsigned interface_type;
- /* data to be passed to the fb driver */
- struct msm_fb_data *fb_data;
-
- /* capabilities supported by the panel */
- uint32_t caps;
-};
-
-struct msm_mddi_client_data {
- void (*suspend)(struct msm_mddi_client_data *);
- void (*resume)(struct msm_mddi_client_data *);
- void (*activate_link)(struct msm_mddi_client_data *);
- void (*remote_write)(struct msm_mddi_client_data *, uint32_t val,
- uint32_t reg);
- uint32_t (*remote_read)(struct msm_mddi_client_data *, uint32_t reg);
- void (*auto_hibernate)(struct msm_mddi_client_data *, int);
- /* custom data that needs to be passed from the board file to a
- * particular client */
- void *private_client_data;
- struct resource *fb_resource;
- /* from the list above */
- unsigned interface_type;
-};
-
-struct msm_mddi_platform_data {
- unsigned int clk_rate;
- void (*power_client)(struct msm_mddi_client_data *, int on);
-
- /* fixup the mfr name, product id */
- void (*fixup)(uint16_t *mfr_name, uint16_t *product_id);
-
- struct resource *fb_resource; /*optional*/
- /* number of clients in the list that follows */
- int num_clients;
- /* array of client information of clients */
- struct {
- unsigned product_id; /* mfr id in top 16 bits, product id
- * in lower 16 bits
- */
- char *name; /* the device name will be the platform
- * device name registered for the client,
- * it should match the name of the associated
- * driver
- */
- unsigned id; /* id for mddi client device node, will also
- * be used as device id of panel devices, if
- * the client device will have multiple panels
- * space must be left here for them
- */
- void *client_data; /* required private client data */
- unsigned int clk_rate; /* optional: if the client requires a
- * different mddi clk rate
- */
- } client_platform_data[];
-};
-
-struct mdp_blit_req;
-struct fb_info;
-struct mdp_device {
- struct device dev;
- void (*dma)(struct mdp_device *mpd, uint32_t addr,
- uint32_t stride, uint32_t w, uint32_t h, uint32_t x,
- uint32_t y, struct msmfb_callback *callback, int interface);
- void (*dma_wait)(struct mdp_device *mdp);
- int (*blit)(struct mdp_device *mdp, struct fb_info *fb,
- struct mdp_blit_req *req);
- void (*set_grp_disp)(struct mdp_device *mdp, uint32_t disp_id);
-};
-
-struct class_interface;
-int register_mdp_client(struct class_interface *class_intf);
-
-/**** private client data structs go below this line ***/
-
-struct msm_mddi_bridge_platform_data {
- /* from board file */
- int (*init)(struct msm_mddi_bridge_platform_data *,
- struct msm_mddi_client_data *);
- int (*uninit)(struct msm_mddi_bridge_platform_data *,
- struct msm_mddi_client_data *);
- /* passed to panel for use by the fb driver */
- int (*blank)(struct msm_mddi_bridge_platform_data *,
- struct msm_mddi_client_data *);
- int (*unblank)(struct msm_mddi_bridge_platform_data *,
- struct msm_mddi_client_data *);
- struct msm_fb_data fb_data;
-};
-
-
-
-#endif
#include <mach/mv78xx0.h>
#include <mach/bridge-regs.h>
#include <plat/cache-feroceon-l2.h>
-#include <plat/ehci-orion.h>
-#include <plat/orion_nand.h>
+#include <linux/platform_data/usb-ehci-orion.h>
+#include <linux/platform_data/mtd-orion_nand.h>
#include <plat/time.h>
#include <plat/common.h>
#include <plat/addr-map.h>
+++ /dev/null
-/*
- * arch/arm/mach-netx/include/mach/eth.h
- *
- * Copyright (c) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2
- * as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#ifndef ASMARM_ARCH_ETH_H
-#define ASMARM_ARCH_ETH_H
-
-struct netxeth_platform_data {
- unsigned int xcno; /* number of xmac/xpec engine this eth uses */
-};
-
-#endif
#include <asm/mach/arch.h>
#include <asm/hardware/vic.h>
#include <mach/netx-regs.h>
-#include <mach/eth.h>
+#include <linux/platform_data/eth-netx.h>
#include "generic.h"
#include "fb.h"
#include <asm/mach/arch.h>
#include <asm/hardware/vic.h>
#include <mach/netx-regs.h>
-#include <mach/eth.h>
+#include <linux/platform_data/eth-netx.h>
#include "generic.h"
#include <asm/mach/arch.h>
#include <asm/hardware/vic.h>
#include <mach/netx-regs.h>
-#include <mach/eth.h>
+#include <linux/platform_data/eth-netx.h>
#include "generic.h"
#include "fb.h"
#include <plat/gpio-nomadik.h>
#include <plat/mtu.h>
-#include <mach/nand.h>
+#include <linux/platform_data/mtd-nomadik-nand.h>
#include <mach/fsmc.h>
#include "cpu-8815.h"
+++ /dev/null
-#ifndef __ASM_ARCH_NAND_H
-#define __ASM_ARCH_NAND_H
-
-struct nomadik_nand_platform_data {
- struct mtd_partition *parts;
- int nparts;
- int options;
- int (*init) (void);
- int (*exit) (void);
-};
-
-#define NAND_IO_DATA 0x40000000
-#define NAND_IO_CMD 0x40800000
-#define NAND_IO_ADDR 0x41000000
-
-#endif /* __ASM_ARCH_NAND_H */
#include <mach/bridge-regs.h>
#include <mach/hardware.h>
#include <mach/orion5x.h>
-#include <plat/orion_nand.h>
-#include <plat/ehci-orion.h>
+#include <linux/platform_data/mtd-orion_nand.h>
+#include <linux/platform_data/usb-ehci-orion.h>
#include <plat/time.h>
#include <plat/common.h>
#include <plat/addr-map.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
-#include <plat/orion_nand.h>
+#include <linux/platform_data/mtd-orion_nand.h>
#include "common.h"
#include "mpp.h"
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
-#include <plat/orion_nand.h>
+#include <linux/platform_data/mtd-orion_nand.h>
#include "common.h"
#include "mpp.h"
#include <mach/pxa25x.h>
#include <mach/gumstix.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include "generic.h"
#include <mach/gumstix.h>
#include <mach/mfp-pxa25x.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/balloon3.h>
#include <mach/audio.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include <mach/udc.h>
#include <mach/pxa27x-udc.h>
-#include <mach/irda.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include "generic.h"
#include "devices.h"
#include <linux/spi/libertas_spi.h>
#include <mach/pxa27x.h>
-#include <mach/ohci.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include "generic.h"
#include <mach/pxa25x.h>
#include <mach/pxa27x.h>
#include <mach/audio.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include <mach/smemc.h>
#include <asm/hardware/it8152.h>
#include <mach/pxa300.h>
#include <mach/pxa27x-udc.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <mach/ohci.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
#include <mach/audio.h>
-#include <mach/pxa3xx-u2d.h>
+#include <linux/platform_data/usb-pxa3xx-ulpi.h>
#include <asm/mach/map.h>
#include <mach/pxa27x.h>
#include <mach/colibri.h>
-#include <mach/mmc.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/pxa27x-udc.h>
#include "generic.h"
#include <asm/mach-types.h>
#include <mach/hardware.h>
-#include <mach/mmc.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/pxa27x.h>
#include <mach/pxa27x-udc.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include "devices.h"
#include "generic.h"
#include <mach/pxa300.h>
#include <mach/colibri.h>
-#include <mach/ohci.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/video-pxafb.h>
#include <mach/audio.h>
#include "generic.h"
#include <mach/pxa320.h>
#include <mach/colibri.h>
-#include <mach/pxafb.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/audio.h>
#include <mach/pxa27x-udc.h>
#include <mach/udc.h>
#include <mach/pxa3xx-regs.h>
#include <mach/mfp-pxa300.h>
#include <mach/colibri.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
#include "generic.h"
#include "devices.h"
#include <asm/mach/irq.h>
#include <mach/pxa25x.h>
-#include <mach/irda.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include <mach/udc.h>
#include <mach/corgi.h>
#include <mach/sharpsl_pm.h>
#include <asm/mach/arch.h>
#include <mach/csb726.h>
#include <mach/pxa27x.h>
-#include <mach/mmc.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/audio.h>
#include <mach/smemc.h>
#include <asm/pmu.h>
#include <mach/udc.h>
-#include <mach/pxa3xx-u2d.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <mach/irda.h>
+#include <linux/platform_data/usb-pxa3xx-ulpi.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/irda-pxaficp.h>
#include <mach/irqs.h>
-#include <mach/ohci.h>
-#include <plat/pxa27x_keypad.h>
-#include <mach/camera.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/keypad-pxa27x.h>
+#include <linux/platform_data/camera-pxa.h>
#include <mach/audio.h>
#include <mach/hardware.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
#include "devices.h"
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/pxa27x-udc.h>
#include <mach/audio.h>
-#include <mach/pxafb.h>
-#include <mach/ohci.h>
-#include <mach/mmc.h>
-#include <plat/pxa27x_keypad.h>
-#include <mach/camera.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/keypad-pxa27x.h>
+#include <linux/platform_data/camera-pxa.h>
#include "generic.h"
#include "devices.h"
#include <mach/eseries-gpio.h>
#include <mach/eseries-irq.h>
#include <mach/audio.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include <mach/udc.h>
-#include <mach/irda.h>
+#include <linux/platform_data/irda-pxaficp.h>
#include "devices.h"
#include "generic.h"
#include <asm/mach/arch.h>
#include <mach/pxa27x.h>
-#include <mach/pxafb.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/hardware.h>
-#include <plat/pxa27x_keypad.h>
-#include <mach/camera.h>
+#include <linux/platform_data/keypad-pxa27x.h>
+#include <linux/platform_data/camera-pxa.h>
#include "devices.h"
#include "generic.h"
#include <asm/mach/flash.h>
#include <mach/pxa25x.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include <mach/udc.h>
#include <mach/gumstix.h>
#include <mach/pxa27x.h>
#include <mach/hx4700.h>
-#include <mach/irda.h>
+#include <linux/platform_data/irda-pxaficp.h>
#include <sound/ak4641.h>
#include <video/platform_lcd.h>
#include <mach/pxa25x.h>
#include <mach/idp.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include <mach/bitfield.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include "generic.h"
#include "devices.h"
+++ /dev/null
-#ifndef __ARCOM_PCMCIA_H
-#define __ARCOM_PCMCIA_H
-
-struct arcom_pcmcia_pdata {
- int cd_gpio;
- int rdy_gpio;
- int pwr_gpio;
- void (*reset)(int state);
-};
-
-#endif
+++ /dev/null
-/*
- camera.h - PXA camera driver header file
-
- Copyright (C) 2003, Intel Corporation
- Copyright (C) 2008, Guennadi Liakhovetski <kernel@pengutronix.de>
-
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation; either version 2 of the License, or
- (at your option) any later version.
-
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
-
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-*/
-
-#ifndef __ASM_ARCH_CAMERA_H_
-#define __ASM_ARCH_CAMERA_H_
-
-#define PXA_CAMERA_MASTER 1
-#define PXA_CAMERA_DATAWIDTH_4 2
-#define PXA_CAMERA_DATAWIDTH_5 4
-#define PXA_CAMERA_DATAWIDTH_8 8
-#define PXA_CAMERA_DATAWIDTH_9 0x10
-#define PXA_CAMERA_DATAWIDTH_10 0x20
-#define PXA_CAMERA_PCLK_EN 0x40
-#define PXA_CAMERA_MCLK_EN 0x80
-#define PXA_CAMERA_PCP 0x100
-#define PXA_CAMERA_HSP 0x200
-#define PXA_CAMERA_VSP 0x400
-
-struct pxacamera_platform_data {
- unsigned long flags;
- unsigned long mclk_10khz;
-};
-
-extern void pxa_set_camera_info(struct pxacamera_platform_data *);
-
-#endif /* __ASM_ARCH_CAMERA_H_ */
+++ /dev/null
-#ifndef ASMARM_ARCH_IRDA_H
-#define ASMARM_ARCH_IRDA_H
-
-/* board specific transceiver capabilities */
-
-#define IR_OFF 1
-#define IR_SIRMODE 2
-#define IR_FIRMODE 4
-
-struct pxaficp_platform_data {
- int transceiver_cap;
- void (*transceiver_mode)(struct device *dev, int mode);
- int (*startup)(struct device *dev);
- void (*shutdown)(struct device *dev);
- int gpio_pwdown; /* powerdown GPIO for the IrDA chip */
- bool gpio_pwdown_inverted; /* gpio_pwdown is inverted */
-};
-
-extern void pxa_set_ficp_info(struct pxaficp_platform_data *info);
-
-#if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x)
-void pxa2xx_transceiver_mode(struct device *dev, int mode);
-#endif
-
-#endif
+++ /dev/null
-#ifndef ASMARM_ARCH_MMC_H
-#define ASMARM_ARCH_MMC_H
-
-#include <linux/mmc/host.h>
-#include <linux/interrupt.h>
-
-struct device;
-struct mmc_host;
-
-struct pxamci_platform_data {
- unsigned int ocr_mask; /* available voltages */
- unsigned long detect_delay_ms; /* delay in millisecond before detecting cards after interrupt */
- int (*init)(struct device *, irq_handler_t , void *);
- int (*get_ro)(struct device *);
- void (*setpower)(struct device *, unsigned int);
- void (*exit)(struct device *, void *);
- int gpio_card_detect; /* gpio detecting card insertion */
- int gpio_card_ro; /* gpio detecting read only toggle */
- bool gpio_card_ro_invert; /* gpio ro is inverted */
- int gpio_power; /* gpio powering up MMC bus */
- bool gpio_power_invert; /* gpio power is inverted */
-};
-
-extern void pxa_set_mci_info(struct pxamci_platform_data *info);
-extern void pxa3xx_set_mci2_info(struct pxamci_platform_data *info);
-extern void pxa3xx_set_mci3_info(struct pxamci_platform_data *info);
-
-#endif
+++ /dev/null
-#ifndef ASMARM_ARCH_OHCI_H
-#define ASMARM_ARCH_OHCI_H
-
-struct device;
-
-struct pxaohci_platform_data {
- int (*init)(struct device *);
- void (*exit)(struct device *);
-
- unsigned long flags;
-#define ENABLE_PORT1 (1 << 0)
-#define ENABLE_PORT2 (1 << 1)
-#define ENABLE_PORT3 (1 << 2)
-#define ENABLE_PORT_ALL (ENABLE_PORT1 | ENABLE_PORT2 | ENABLE_PORT3)
-
-#define POWER_SENSE_LOW (1 << 3)
-#define POWER_CONTROL_LOW (1 << 4)
-#define NO_OC_PROTECTION (1 << 5)
-#define OC_MODE_GLOBAL (0 << 6)
-#define OC_MODE_PERPORT (1 << 6)
-
- int power_on_delay; /* Power On to Power Good time - in ms
- * HCD must wait for this duration before
- * accessing a powered on port
- */
- int port_mode;
-#define PMM_NPS_MODE 1
-#define PMM_GLOBAL_MODE 2
-#define PMM_PERPORT_MODE 3
-
- int power_budget;
-};
-
-extern void pxa_set_ohci_info(struct pxaohci_platform_data *info);
-
-#endif
+++ /dev/null
-#ifndef _INCLUDE_PALMASOC_H_
-#define _INCLUDE_PALMASOC_H_
-
-struct palm27x_asoc_info {
- int jack_gpio;
-};
-
-#endif
+++ /dev/null
-/*
- * Generic PXA PATA driver
- *
- * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; see the file COPYING. If not, write to
- * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef __MACH_PATA_PXA_H__
-#define __MACH_PATA_PXA_H__
-
-struct pata_pxa_pdata {
- /* PXA DMA DREQ<0:2> pin */
- uint32_t dma_dreq;
- /* Register shift */
- uint32_t reg_shift;
- /* IRQ flags */
- uint32_t irq_flags;
-};
-
-#endif /* __MACH_PATA_PXA_H__ */
+++ /dev/null
-/*
- * PXA3xx U2D header
- *
- * Copyright (C) 2010 CompuLab Ltd.
- *
- * Igor Grinberg <grinberg@compulab.co.il>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __PXA310_U2D__
-#define __PXA310_U2D__
-
-#include <linux/usb/ulpi.h>
-
-struct pxa3xx_u2d_platform_data {
-
-#define ULPI_SER_6PIN (1 << 0)
-#define ULPI_SER_3PIN (1 << 1)
- unsigned int ulpi_mode;
-
- int (*init)(struct device *);
- void (*exit)(struct device *);
-};
-
-
-/* Start PXA3xx U2D host */
-int pxa3xx_u2d_start_hc(struct usb_bus *host);
-/* Stop PXA3xx U2D host */
-void pxa3xx_u2d_stop_hc(struct usb_bus *host);
-
-extern void pxa3xx_set_u2d_info(struct pxa3xx_u2d_platform_data *info);
-
-#endif /* __PXA310_U2D__ */
+++ /dev/null
-#ifndef __ASM_ARCH_PXA930_ROTARY_H
-#define __ASM_ARCH_PXA930_ROTARY_H
-
-/* NOTE:
- *
- * rotary can be either interpreted as a ralative input event (e.g.
- * REL_WHEEL or REL_HWHEEL) or a specific key event (e.g. UP/DOWN
- * or LEFT/RIGHT), depending on if up_key & down_key are assigned
- * or rel_code is assigned a non-zero value. When all are non-zero,
- * up_key and down_key will be preferred.
- */
-struct pxa930_rotary_platform_data {
- int up_key;
- int down_key;
- int rel_code;
-};
-
-void __init pxa930_set_rotarykey_info(struct pxa930_rotary_platform_data *info);
-
-#endif /* __ASM_ARCH_PXA930_ROTARY_H */
+++ /dev/null
-#ifndef __ASM_ARCH_PXA930_TRKBALL_H
-#define __ASM_ARCH_PXA930_TRKBALL_H
-
-struct pxa930_trkball_platform_data {
- int x_filter;
- int y_filter;
-};
-
-#endif /* __ASM_ARCH_PXA930_TRKBALL_H */
-
+++ /dev/null
-/*
- * arch/arm/mach-pxa/include/mach/pxafb.h
- *
- * Support for the xscale frame buffer.
- *
- * Author: Jean-Frederic Clere
- * Created: Sep 22, 2003
- * Copyright: jfclere@sinix.net
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/fb.h>
-#include <mach/regs-lcd.h>
-
-/*
- * Supported LCD connections
- *
- * bits 0 - 3: for LCD panel type:
- *
- * STN - for passive matrix
- * DSTN - for dual scan passive matrix
- * TFT - for active matrix
- *
- * bits 4 - 9 : for bus width
- * bits 10-17 : for AC Bias Pin Frequency
- * bit 18 : for output enable polarity
- * bit 19 : for pixel clock edge
- * bit 20 : for output pixel format when base is RGBT16
- */
-#define LCD_CONN_TYPE(_x) ((_x) & 0x0f)
-#define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f)
-
-#define LCD_TYPE_MASK 0xf
-#define LCD_TYPE_UNKNOWN 0
-#define LCD_TYPE_MONO_STN 1
-#define LCD_TYPE_MONO_DSTN 2
-#define LCD_TYPE_COLOR_STN 3
-#define LCD_TYPE_COLOR_DSTN 4
-#define LCD_TYPE_COLOR_TFT 5
-#define LCD_TYPE_SMART_PANEL 6
-#define LCD_TYPE_MAX 7
-
-#define LCD_MONO_STN_4BPP ((4 << 4) | LCD_TYPE_MONO_STN)
-#define LCD_MONO_STN_8BPP ((8 << 4) | LCD_TYPE_MONO_STN)
-#define LCD_MONO_DSTN_8BPP ((8 << 4) | LCD_TYPE_MONO_DSTN)
-#define LCD_COLOR_STN_8BPP ((8 << 4) | LCD_TYPE_COLOR_STN)
-#define LCD_COLOR_DSTN_16BPP ((16 << 4) | LCD_TYPE_COLOR_DSTN)
-#define LCD_COLOR_TFT_8BPP ((8 << 4) | LCD_TYPE_COLOR_TFT)
-#define LCD_COLOR_TFT_16BPP ((16 << 4) | LCD_TYPE_COLOR_TFT)
-#define LCD_COLOR_TFT_18BPP ((18 << 4) | LCD_TYPE_COLOR_TFT)
-#define LCD_SMART_PANEL_8BPP ((8 << 4) | LCD_TYPE_SMART_PANEL)
-#define LCD_SMART_PANEL_16BPP ((16 << 4) | LCD_TYPE_SMART_PANEL)
-#define LCD_SMART_PANEL_18BPP ((18 << 4) | LCD_TYPE_SMART_PANEL)
-
-#define LCD_AC_BIAS_FREQ(x) (((x) & 0xff) << 10)
-#define LCD_BIAS_ACTIVE_HIGH (0 << 18)
-#define LCD_BIAS_ACTIVE_LOW (1 << 18)
-#define LCD_PCLK_EDGE_RISE (0 << 19)
-#define LCD_PCLK_EDGE_FALL (1 << 19)
-#define LCD_ALTERNATE_MAPPING (1 << 20)
-
-/*
- * This structure describes the machine which we are running on.
- * It is set in linux/arch/arm/mach-pxa/machine_name.c and used in the probe routine
- * of linux/drivers/video/pxafb.c
- */
-struct pxafb_mode_info {
- u_long pixclock;
-
- u_short xres;
- u_short yres;
-
- u_char bpp;
- u_int cmap_greyscale:1,
- depth:8,
- transparency:1,
- unused:22;
-
- /* Parallel Mode Timing */
- u_char hsync_len;
- u_char left_margin;
- u_char right_margin;
-
- u_char vsync_len;
- u_char upper_margin;
- u_char lower_margin;
- u_char sync;
-
- /* Smart Panel Mode Timing - see PXA27x DM 7.4.15.0.3 for details
- * Note:
- * 1. all parameters in nanosecond (ns)
- * 2. a0cs{rd,wr}_set_hld are controlled by the same register bits
- * in pxa27x and pxa3xx, initialize them to the same value or
- * the larger one will be used
- * 3. same to {rd,wr}_pulse_width
- *
- * 4. LCD_PCLK_EDGE_{RISE,FALL} controls the L_PCLK_WR polarity
- * 5. sync & FB_SYNC_HOR_HIGH_ACT controls the L_LCLK_A0
- * 6. sync & FB_SYNC_VERT_HIGH_ACT controls the L_LCLK_RD
- */
- unsigned a0csrd_set_hld; /* A0 and CS Setup/Hold Time before/after L_FCLK_RD */
- unsigned a0cswr_set_hld; /* A0 and CS Setup/Hold Time before/after L_PCLK_WR */
- unsigned wr_pulse_width; /* L_PCLK_WR pulse width */
- unsigned rd_pulse_width; /* L_FCLK_RD pulse width */
- unsigned cmd_inh_time; /* Command Inhibit time between two writes */
- unsigned op_hold_time; /* Output Hold time from L_FCLK_RD negation */
-};
-
-struct pxafb_mach_info {
- struct pxafb_mode_info *modes;
- unsigned int num_modes;
-
- unsigned int lcd_conn;
- unsigned long video_mem_size;
-
- u_int fixed_modes:1,
- cmap_inverse:1,
- cmap_static:1,
- acceleration_enabled:1,
- unused:28;
-
- /* The following should be defined in LCCR0
- * LCCR0_Act or LCCR0_Pas Active or Passive
- * LCCR0_Sngl or LCCR0_Dual Single/Dual panel
- * LCCR0_Mono or LCCR0_Color Mono/Color
- * LCCR0_4PixMono or LCCR0_8PixMono (in mono single mode)
- * LCCR0_DMADel(Tcpu) (optional) DMA request delay
- *
- * The following should not be defined in LCCR0:
- * LCCR0_OUM, LCCR0_BM, LCCR0_QDM, LCCR0_DIS, LCCR0_EFM
- * LCCR0_IUM, LCCR0_SFM, LCCR0_LDM, LCCR0_ENB
- */
- u_int lccr0;
- /* The following should be defined in LCCR3
- * LCCR3_OutEnH or LCCR3_OutEnL Output enable polarity
- * LCCR3_PixRsEdg or LCCR3_PixFlEdg Pixel clock edge type
- * LCCR3_Acb(X) AB Bias pin frequency
- * LCCR3_DPC (optional) Double Pixel Clock mode (untested)
- *
- * The following should not be defined in LCCR3
- * LCCR3_HSP, LCCR3_VSP, LCCR0_Pcd(x), LCCR3_Bpp
- */
- u_int lccr3;
- /* The following should be defined in LCCR4
- * LCCR4_PAL_FOR_0 or LCCR4_PAL_FOR_1 or LCCR4_PAL_FOR_2
- *
- * All other bits in LCCR4 should be left alone.
- */
- u_int lccr4;
- void (*pxafb_backlight_power)(int);
- void (*pxafb_lcd_power)(int, struct fb_var_screeninfo *);
- void (*smart_update)(struct fb_info *);
-};
-
-void pxa_set_fb_info(struct device *, struct pxafb_mach_info *);
-unsigned long pxafb_get_hsync_time(struct device *dev);
-
-#ifdef CONFIG_FB_PXA_SMARTPANEL
-extern int pxafb_smart_queue(struct fb_info *info, uint16_t *cmds, int);
-extern int pxafb_smart_flush(struct fb_info *info);
-#else
-static inline int pxafb_smart_queue(struct fb_info *info,
- uint16_t *cmds, int n)
-{
- return 0;
-}
-
-static inline int pxafb_smart_flush(struct fb_info *info)
-{
- return 0;
-}
-#endif
#include <asm/mach/irq.h>
#include <mach/pxa300.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include <mach/littleton.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/lpd270.h>
#include <mach/audio.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <mach/irda.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/smemc.h>
#include "generic.h"
#include <mach/audio.h>
#include <mach/lubbock.h>
#include <mach/udc.h>
-#include <mach/irda.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include <mach/pm.h>
#include <mach/smemc.h>
#include <mach/pxa27x.h>
#include <mach/magician.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <mach/irda.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include "devices.h"
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/mainstone.h>
#include <mach/audio.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <mach/irda.h>
-#include <mach/ohci.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include <mach/smemc.h>
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/regs-rtc.h>
-#include <plat/pxa27x_keypad.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/keypad-pxa27x.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include <mach/udc.h>
#include <mach/pxa27x-udc.h>
-#include <mach/camera.h>
+#include <linux/platform_data/camera-pxa.h>
#include <mach/audio.h>
#include <mach/smemc.h>
#include <media/soc_camera.h>
#include <linux/gpio.h>
#include <linux/i2c/pxa-i2c.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/pxa320.h>
#include <mach/mxm8x10.h>
#include <mach/pxa27x.h>
#include <mach/audio.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <mach/irda.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/irda-pxaficp.h>
#include <mach/udc.h>
-#include <mach/palmasoc.h>
+#include <linux/platform_data/asoc-palm27x.h>
#include <mach/palm27x.h>
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/audio.h>
#include <mach/palmld.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <mach/irda.h>
-#include <plat/pxa27x_keypad.h>
-#include <mach/palmasoc.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/keypad-pxa27x.h>
+#include <linux/platform_data/asoc-palm27x.h>
#include <mach/palm27x.h>
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/audio.h>
#include <mach/palmt5.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <mach/irda.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include <mach/udc.h>
-#include <mach/palmasoc.h>
+#include <linux/platform_data/asoc-palm27x.h>
#include <mach/palm27x.h>
#include "generic.h"
#include <mach/pxa25x.h>
#include <mach/audio.h>
#include <mach/palmtc.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <mach/irda.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/irda-pxaficp.h>
#include <mach/udc.h>
#include "generic.h"
#include <mach/pxa25x.h>
#include <mach/audio.h>
#include <mach/palmte2.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <mach/irda.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/irda-pxaficp.h>
#include <mach/udc.h>
-#include <mach/palmasoc.h>
+#include <linux/platform_data/asoc-palm27x.h>
#include "generic.h"
#include "devices.h"
#include <mach/pxa27x-udc.h>
#include <mach/audio.h>
#include <mach/palmtreo.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <mach/irda.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include <mach/udc.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/pxa2xx-regs.h>
-#include <mach/palmasoc.h>
-#include <mach/camera.h>
+#include <linux/platform_data/asoc-palm27x.h>
+#include <linux/platform_data/camera-pxa.h>
#include <mach/palm27x.h>
#include <sound/pxa2xx-lib.h>
#include <mach/pxa27x.h>
#include <mach/audio.h>
#include <mach/palmtx.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <mach/irda.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include <mach/udc.h>
-#include <mach/palmasoc.h>
+#include <linux/platform_data/asoc-palm27x.h>
#include <mach/palm27x.h>
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/audio.h>
#include <mach/palmz72.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <mach/irda.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include <mach/udc.h>
-#include <mach/palmasoc.h>
+#include <linux/platform_data/asoc-palm27x.h>
#include <mach/palm27x.h>
#include <mach/pm.h>
-#include <mach/camera.h>
+#include <linux/platform_data/camera-pxa.h>
#include <media/soc_camera.h>
#include <media/soc_camera.h>
-#include <mach/camera.h>
+#include <linux/platform_data/camera-pxa.h>
#include <asm/mach/map.h>
#include <mach/pxa27x.h>
#include <mach/audio.h>
-#include <mach/mmc.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/pcm990_baseboard.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include "devices.h"
#include "generic.h"
#include <asm/mach/irq.h>
#include <mach/pxa25x.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include <mach/udc.h>
-#include <mach/irda.h>
+#include <linux/platform_data/irda-pxaficp.h>
#include <mach/poodle.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include <asm/hardware/scoop.h>
#include <asm/hardware/locomo.h>
#include <mach/irqs.h>
#include <mach/pxa27x.h>
#include <mach/reset.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/pm.h>
#include <mach/dma.h>
#include <mach/smemc.h>
#include <mach/pxa2xx-regs.h>
#include <mach/mfp-pxa25x.h>
#include <mach/reset.h>
-#include <mach/irda.h>
+#include <linux/platform_data/irda-pxaficp.h>
void pxa2xx_clear_reset_status(unsigned int mask)
{
#include <mach/hardware.h>
#include <mach/regs-u2d.h>
-#include <mach/pxa3xx-u2d.h>
+#include <linux/platform_data/usb-pxa3xx-ulpi.h>
struct pxa3xx_u2d_ulpi {
struct clk *clk;
#include <mach/hardware.h>
#include <mach/pxa3xx-regs.h>
#include <mach/reset.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/pm.h>
#include <mach/dma.h>
#include <mach/smemc.h>
#include <asm/mach/arch.h>
#include <mach/pxa300.h>
-#include <mach/ohci.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
#include "generic.h"
#include "devices.h"
#include <asm/mach/flash.h>
#include <mach/pxa930.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include "devices.h"
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/pxa27x-udc.h>
#include <mach/reset.h>
-#include <mach/irda.h>
-#include <mach/mmc.h>
-#include <mach/ohci.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/video-pxafb.h>
#include <mach/spitz.h>
#include <mach/sharpsl_pm.h>
#include <mach/smemc.h>
#include <asm/mach/flash.h>
#include <mach/pxa27x.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include <mach/udc.h>
#include <mach/pxa27x-udc.h>
#include <mach/smemc.h>
#include <asm/mach/arch.h>
#include <mach/pxa930.h>
-#include <mach/pxafb.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include "devices.h"
#include "generic.h"
#include <mach/pxa25x.h>
#include <mach/reset.h>
-#include <mach/irda.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include <mach/udc.h>
#include <mach/tosa_bt.h>
#include <mach/audio.h>
#include <mach/pxa27x.h>
#include <mach/trizeps4.h>
#include <mach/audio.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <mach/irda.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/irda-pxaficp.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/smemc.h>
#include "generic.h"
#include <mach/pxa25x.h>
#include <mach/audio.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include <mach/regs-uart.h>
-#include <mach/arcom-pcmcia.h>
+#include <linux/platform_data/pcmcia-pxa2xx_viper.h>
#include <mach/viper.h>
#include <asm/setup.h>
#include <mach/pxa27x.h>
#include <mach/audio.h>
#include <mach/vpac270.h>
-#include <mach/mmc.h>
-#include <mach/pxafb.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <mach/pxa27x-udc.h>
#include <mach/udc.h>
-#include <mach/pata_pxa.h>
+#include <linux/platform_data/ata-pxa.h>
#include "generic.h"
#include "devices.h"
#include <mach/pxa27x.h>
#include <mach/mfp-pxa27x.h>
#include <mach/z2.h>
-#include <mach/pxafb.h>
-#include <mach/mmc.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/keypad-pxa27x.h>
#include <mach/pm.h>
#include "generic.h"
#include <mach/pxa27x.h>
#include <mach/regs-uart.h>
-#include <mach/ohci.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include <mach/pxa27x-udc.h>
#include <mach/udc.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include <mach/pm.h>
#include <mach/audio.h>
-#include <mach/arcom-pcmcia.h>
+#include <linux/platform_data/pcmcia-pxa2xx_viper.h>
#include <mach/zeus.h>
#include <mach/smemc.h>
#include <asm/mach/arch.h>
#include <mach/pxa3xx.h>
#include <mach/audio.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
#include <mach/zylonite.h>
-#include <mach/mmc.h>
-#include <mach/ohci.h>
-#include <plat/pxa27x_keypad.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/keypad-pxa27x.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
#include "devices.h"
#include "generic.h"
#include <asm/irq.h>
#include <mach/regs-gpio.h>
-#include <mach/leds-gpio.h>
+#include <linux/platform_data/leds-s3c24xx.h>
-#include <plat/nand.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <plat/common-smdk.h>
#include <plat/gpio-cfg.h>
+++ /dev/null
-/* arch/arm/mach-s3c2410/include/mach/leds-gpio.h
- *
- * Copyright (c) 2006 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C24XX - LEDs GPIO connector
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_LEDSGPIO_H
-#define __ASM_ARCH_LEDSGPIO_H "leds-gpio.h"
-
-#define S3C24XX_LEDF_ACTLOW (1<<0) /* LED is on when GPIO low */
-#define S3C24XX_LEDF_TRISTATE (1<<1) /* tristate to turn off */
-
-struct s3c24xx_led_platdata {
- unsigned int gpio;
- unsigned int flags;
-
- char *name;
- char *def_trigger;
-};
-
-#endif /* __ASM_ARCH_LEDSGPIO_H */
#include <mach/regs-lcd.h>
#include <mach/regs-gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/gpio-cfg.h>
#include <mach/regs-gpio.h>
#include <mach/regs-mem.h>
#include <mach/regs-lcd.h>
-#include <plat/nand.h>
-#include <plat/iic.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
-#include <plat/audio-simtec.h>
+#include <linux/platform_data/asoc-s3c24xx_simtec.h>
#include "simtec.h"
#include "common.h"
#include <mach/regs-gpio.h>
#include <mach/regs-mem.h>
#include <mach/regs-lcd.h>
-#include <plat/nand.h>
-#include <plat/iic.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
-#include <plat/mci.h>
+#include <linux/platform_data/mmc-s3cmci.h>
#include "common.h"
#include <mach/regs-mem.h>
#include <mach/regs-lcd.h>
-#include <plat/hwmon.h>
-#include <plat/nand.h>
-#include <plat/iic.h>
+#include <linux/platform_data/hwmon-s3c.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <mach/fb.h>
#include <linux/mtd/mtd.h>
#include <plat/cpu.h>
#include <plat/cpu-freq.h>
#include <plat/gpio-cfg.h>
-#include <plat/audio-simtec.h>
+#include <linux/platform_data/asoc-s3c24xx_simtec.h>
#include "simtec.h"
#include "common.h"
#include <mach/regs-gpio.h>
#include <mach/fb.h>
-#include <plat/usb-control.h>
+#include <linux/platform_data/usb-ohci-s3c2410.h>
#include <mach/regs-mem.h>
#include <mach/hardware.h>
#include <mach/gta02.h>
#include <plat/regs-serial.h>
-#include <plat/nand.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/pm.h>
-#include <plat/udc.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
#include <plat/gpio-cfg.h>
-#include <plat/iic.h>
-#include <plat/ts.h>
+#include <linux/platform_data/i2c-s3c2410.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#include "common.h"
#include <mach/h1940.h>
#include <mach/h1940-latch.h>
#include <mach/fb.h>
-#include <plat/udc.h>
-#include <plat/iic.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
#include <plat/clock.h>
#include <plat/cpu.h>
#include <plat/pll.h>
#include <plat/pm.h>
-#include <plat/mci.h>
-#include <plat/ts.h>
+#include <linux/platform_data/mmc-s3cmci.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#include <sound/uda1380.h>
#include <asm/mach/irq.h>
#include <plat/regs-serial.h>
-#include <plat/nand.h>
-#include <plat/iic.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <mach/regs-power.h>
#include <mach/regs-gpio.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/pm.h>
-#include <plat/udc.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
static struct map_desc jive_iodesc[] __initdata = {
};
#include <plat/regs-serial.h>
#include <mach/regs-gpio.h>
-#include <mach/leds-gpio.h>
+#include <linux/platform_data/leds-s3c24xx.h>
#include <mach/regs-mem.h>
#include <mach/regs-lcd.h>
#include <mach/irqs.h>
-#include <plat/nand.h>
-#include <plat/iic.h>
-#include <plat/mci.h>
-#include <plat/udc.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/i2c-s3c2410.h>
+#include <linux/platform_data/mmc-s3cmci.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <asm/mach-types.h>
#include <mach/fb.h>
-#include <mach/leds-gpio.h>
+#include <linux/platform_data/leds-s3c24xx.h>
#include <mach/regs-gpio.h>
#include <mach/regs-lcd.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/regs-serial.h>
#include <plat/clock.h>
#include <plat/cpu.h>
#include <plat/devs.h>
-#include <plat/mci.h>
+#include <linux/platform_data/mmc-s3cmci.h>
#include <plat/s3c2410.h>
-#include <plat/udc.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
#include "common.h"
//#include <asm/debug-ll.h>
#include <mach/regs-gpio.h>
#include <plat/regs-serial.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
#include <plat/s3c2410.h>
#include <mach/regs-gpio.h>
#include <mach/regs-mem.h>
#include <mach/regs-lcd.h>
-#include <plat/nand.h>
-#include <plat/iic.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <plat/s3c2410.h>
#include <plat/clock.h>
#include <plat/devs.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/cpu.h>
#include "common.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/leds-gpio.h>
+#include <linux/platform_data/leds-s3c24xx.h>
#include <mach/regs-lcd.h>
#include <plat/regs-serial.h>
#include <mach/fb.h>
-#include <plat/nand.h>
-#include <plat/udc.h>
-#include <plat/iic.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/common-smdk.h>
#include <plat/gpio-cfg.h>
#include <plat/clock.h>
#include <plat/regs-serial.h>
#include <plat/regs-iic.h>
-#include <plat/mci.h>
-#include <plat/udc.h>
-#include <plat/nand.h>
-#include <plat/iic.h>
+#include <linux/platform_data/mmc-s3cmci.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/pm.h>
#include <plat/irq.h>
-#include <plat/ts.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#include <sound/uda1380.h>
#include <mach/regs-lcd.h>
#include <mach/h1940.h>
-#include <plat/nand.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <mach/fb.h>
#include <plat/clock.h>
#include <asm/mach-types.h>
#include <plat/regs-serial.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <mach/regs-lcd.h>
#include <mach/idle.h>
-#include <plat/udc.h>
-#include <plat/iic.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <mach/fb.h>
#include <plat/s3c2410.h>
#include <mach/regs-s3c2443-clock.h>
#include <mach/idle.h>
-#include <mach/leds-gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/leds-s3c24xx.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/s3c2416.h>
#include <plat/gpio-cfg.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
-#include <plat/nand.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <plat/sdhci.h>
-#include <plat/udc.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
#include <linux/platform_data/s3c-hsudc.h>
#include <plat/regs-fb-v4.h>
#include <mach/idle.h>
#include <mach/fb.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/s3c2410.h>
#include <plat/s3c244x.h>
#include <mach/idle.h>
#include <mach/fb.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/s3c2410.h>
#include <plat/s3c2443.h>
#include <asm/mach-types.h>
#include <plat/regs-serial.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/regs-serial.h>
#include <mach/regs-gpio.h>
-#include <mach/leds-gpio.h>
+#include <linux/platform_data/leds-s3c24xx.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
-#include <plat/iic.h>
-#include <plat/audio-simtec.h>
+#include <linux/platform_data/i2c-s3c2410.h>
+#include <linux/platform_data/asoc-s3c24xx_simtec.h>
#include "simtec.h"
#include "common.h"
#include <mach/idle.h>
#include <mach/fb.h>
-#include <plat/iic.h>
-#include <plat/nand.h>
+#include <linux/platform_data/i2c-s3c2410.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <plat/s3c2410.h>
#include <plat/s3c2412.h>
struct platform_device;
#include <plat/gpio-cfg.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <mach/hardware.h>
#include <mach/regs-gpio.h>
#include <mach/hardware.h>
#include <mach/regs-gpio.h>
-#include <plat/audio-simtec.h>
+#include <linux/platform_data/asoc-s3c24xx_simtec.h>
#include <plat/devs.h>
#include "simtec.h"
#include <mach/hardware.h>
#include <asm/irq.h>
-#include <plat/usb-control.h>
+#include <linux/platform_data/usb-ohci-s3c2410.h>
#include <plat/devs.h>
#include "simtec.h"
#include <mach/dma.h>
#include <plat/devs.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-s3c.h>
#include <plat/gpio-cfg.h>
static const char *rclksrc[] = {
#include <asm/mach-types.h>
#include <plat/regs-serial.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/fb.h>
#include <plat/regs-fb-v4.h>
#include <sound/wm8962.h>
#include <sound/wm9081.h>
-#include <plat/s3c64xx-spi.h>
+#include <linux/platform_data/spi-s3c64xx.h>
#include <mach/crag6410.h>
#include <plat/fb.h>
#include <plat/sdhci.h>
#include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
+#include <linux/platform_data/spi-s3c64xx.h>
#include <plat/keypad.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/adc.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/pm.h>
#include "common.h"
#include <asm/mach-types.h>
#include <plat/regs-serial.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/fb.h>
-#include <plat/nand.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/devs.h>
#include <plat/fb.h>
-#include <plat/nand.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <plat/regs-serial.h>
-#include <plat/ts.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#include <plat/regs-fb-v4.h>
#include <video/platform_lcd.h>
#include <asm/mach-types.h>
#include <plat/regs-serial.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/fb.h>
#include <plat/clock.h>
#include <plat/cpu.h>
#include <plat/devs.h>
#include <plat/fb.h>
-#include <plat/nand.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <plat/regs-serial.h>
-#include <plat/ts.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#include <plat/regs-fb-v4.h>
#include <video/platform_lcd.h>
#include <plat/clock.h>
#include <plat/cpu.h>
#include <plat/devs.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
-#include <plat/hwmon.h>
+#include <linux/platform_data/hwmon-s3c.h>
#include <plat/regs-serial.h>
-#include <plat/usb-control.h>
+#include <linux/platform_data/usb-ohci-s3c2410.h>
#include <plat/sdhci.h>
-#include <plat/ts.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#include <video/platform_lcd.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include "common.h"
#include <mach/regs-gpio.h>
#include <mach/regs-sys.h>
#include <mach/regs-srom.h>
-#include <plat/ata.h>
-#include <plat/iic.h>
+#include <linux/platform_data/ata-samsung_cf.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/fb.h>
#include <plat/gpio-cfg.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/adc.h>
-#include <plat/ts.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#include <plat/keypad.h>
#include <plat/backlight.h>
#include <plat/regs-fb-v4.h>
struct platform_device; /* don't need the contents */
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c0_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c1_cfg_gpio(struct platform_device *dev)
#include <mach/map.h>
#include <mach/regs-clock.h>
#include <plat/gpio-cfg.h>
-#include <plat/ata.h>
+#include <linux/platform_data/ata-samsung_cf.h>
void s3c64xx_ide_setup_gpio(void)
{
#include <linux/gpio.h>
#include <plat/gpio-cfg.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-s3c.h>
#include <mach/map.h>
#include <mach/dma.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/pll.h>
#include <plat/adc.h>
-#include <plat/ts.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#include <plat/s5p-time.h>
#include <plat/backlight.h>
#include <plat/fb.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/pll.h>
#include <plat/adc.h>
-#include <plat/ts.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#include <plat/s5p-time.h>
#include <plat/backlight.h>
#include <plat/fb.h>
struct platform_device; /* don't need the contents */
#include <plat/gpio-cfg.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <mach/i2c.h>
struct platform_device; /* don't need the contents */
#include <plat/gpio-cfg.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <mach/i2c.h>
#include <linux/gpio.h>
#include <plat/gpio-cfg.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-s3c.h>
#include <mach/map.h>
#include <mach/dma.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/fb.h>
-#include <plat/iic.h>
-#include <plat/ata.h>
+#include <linux/platform_data/i2c-s3c2410.h>
+#include <linux/platform_data/ata-samsung_cf.h>
#include <plat/adc.h>
#include <plat/keypad.h>
-#include <plat/ts.h>
-#include <plat/audio.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
+#include <linux/platform_data/asoc-s3c.h>
#include <plat/backlight.h>
#include <plat/regs-fb-v4.h>
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c0_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
#include <linux/gpio.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c1_cfg_gpio(struct platform_device *dev)
#include <linux/gpio.h>
#include <plat/gpio-cfg.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-s3c.h>
#include <mach/map.h>
#include <mach/dma.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/fb.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/keypad.h>
#include <plat/sdhci.h>
#include <plat/clock.h>
#include <plat/regs-serial.h>
#include <plat/devs.h>
#include <plat/cpu.h>
-#include <plat/ata.h>
-#include <plat/iic.h>
+#include <linux/platform_data/ata-samsung_cf.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/pm.h>
#include <plat/s5p-time.h>
#include <plat/mfc.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#include <plat/adc.h>
-#include <plat/ts.h>
-#include <plat/ata.h>
-#include <plat/iic.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
+#include <linux/platform_data/ata-samsung_cf.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/keypad.h>
#include <plat/pm.h>
#include <plat/fb.h>
#include <plat/regs-serial.h>
#include <plat/devs.h>
#include <plat/cpu.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/s5p-time.h>
#include "common.h"
struct platform_device; /* don't need the contents */
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c0_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c1_cfg_gpio(struct platform_device *dev)
struct platform_device; /* don't need the contents */
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/gpio-cfg.h>
void s3c_i2c2_cfg_gpio(struct platform_device *dev)
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
#include <mach/assabet.h>
-#include <mach/mcp.h>
+#include <linux/platform_data/mfd-mcp-sa11x0.h>
#include <mach/irqs.h>
#include "generic.h"
#include <asm/mach/serial_sa1100.h>
#include <mach/cerf.h>
-#include <mach/mcp.h>
+#include <linux/platform_data/mfd-mcp-sa11x0.h>
#include <mach/irqs.h>
#include "generic.h"
#include <asm/hardware/scoop.h>
#include <asm/mach/sharpsl_param.h>
#include <asm/hardware/locomo.h>
-#include <mach/mcp.h>
+#include <linux/platform_data/mfd-mcp-sa11x0.h>
#include <mach/irqs.h>
#include "generic.h"
+++ /dev/null
-/*
- * arch/arm/mach-sa1100/include/mach/mcp.h
- *
- * Copyright (C) 2005 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ASM_ARM_ARCH_MCP_H
-#define __ASM_ARM_ARCH_MCP_H
-
-#include <linux/types.h>
-
-struct mcp_plat_data {
- u32 mccr0;
- u32 mccr1;
- unsigned int sclk_rate;
- void *codec_pdata;
-};
-
-#endif
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
-#include <mach/mcp.h>
+#include <linux/platform_data/mfd-mcp-sa11x0.h>
#include <mach/irqs.h>
#include "generic.h"
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
-#include <mach/mcp.h>
+#include <linux/platform_data/mfd-mcp-sa11x0.h>
#include <mach/shannon.h>
#include <mach/irqs.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
-#include <mach/mcp.h>
+#include <linux/platform_data/mfd-mcp-sa11x0.h>
#include <mach/simpad.h>
#include <mach/irqs.h>
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/i2c.h>
+#include <linux/platform_data/mmc-sdhci-tegra.h>
#include <sound/wm8903.h>
#include <mach/tegra_wm8903_pdata.h>
#include <mach/iomap.h>
#include <mach/irqs.h>
-#include <mach/sdhci.h>
#include "board.h"
#include "board-harmony.h"
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/rfkill-gpio.h>
+#include <linux/platform_data/mmc-sdhci-tegra.h>
#include <asm/hardware/gic.h>
#include <asm/mach-types.h>
#include <mach/iomap.h>
#include <mach/irqs.h>
-#include <mach/sdhci.h>
#include "board.h"
#include "board-paz00.h"
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/platform_data/tegra_usb.h>
+#include <linux/platform_data/mmc-sdhci-tegra.h>
#include <asm/hardware/gic.h>
#include <asm/mach-types.h>
#include <asm/setup.h>
#include <mach/iomap.h>
-#include <mach/sdhci.h>
#include "board.h"
#include "clock.h"
+++ /dev/null
-/*
- * include/asm-arm/arch-tegra/include/mach/sdhci.h
- *
- * Copyright (C) 2009 Palm, Inc.
- * Author: Yvonne Yip <y@palm.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-#ifndef __ASM_ARM_ARCH_TEGRA_SDHCI_H
-#define __ASM_ARM_ARCH_TEGRA_SDHCI_H
-
-#include <linux/mmc/host.h>
-
-struct tegra_sdhci_platform_data {
- int cd_gpio;
- int wp_gpio;
- int power_gpio;
- int is_8bit;
- int pm_flags;
-};
-
-#endif
#include <mach/setup.h>
#include <mach/devices.h>
#include <mach/irqs.h>
-#include <mach/crypto-ux500.h>
+#include <linux/platform_data/crypto-ux500.h>
#include "ste-dma40-db8500.h"
#include "devices-db8500.h"
#include <mach/hardware.h>
#include <mach/setup.h>
#include <mach/devices.h>
-#include <mach/usb.h>
+#include <linux/platform_data/usb-musb-ux500.h>
#include <mach/db8500-regs.h>
#include "devices-db8500.h"
#include <linux/sys_soc.h>
#include <linux/amba/bus.h>
#include <linux/platform_data/i2c-nomadik.h>
-#include <mach/crypto-ux500.h>
+#include <linux/platform_data/crypto-ux500.h>
struct spi_master_cntlr;
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2011
- *
- * Author: Joakim Bech <joakim.xx.bech@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- */
-#ifndef _CRYPTO_UX500_H
-#define _CRYPTO_UX500_H
-#include <linux/dmaengine.h>
-#include <plat/ste_dma40.h>
-
-struct hash_platform_data {
- void *mem_to_engine;
- bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
-};
-
-struct cryp_platform_data {
- struct stedma40_chan_cfg mem_to_engine;
- struct stedma40_chan_cfg engine_to_mem;
-};
-
-#endif
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2011
- *
- * Author: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
- * License terms: GNU General Public License (GPL) version 2
- */
-#ifndef __ASM_ARCH_USB_H
-#define __ASM_ARCH_USB_H
-
-#include <linux/dmaengine.h>
-
-#define UX500_MUSB_DMA_NUM_RX_CHANNELS 8
-#define UX500_MUSB_DMA_NUM_TX_CHANNELS 8
-
-struct ux500_musb_board_data {
- void **dma_rx_param_array;
- void **dma_tx_param_array;
- u32 num_rx_channels;
- u32 num_tx_channels;
- bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
-};
-
-void ux500_add_usb(struct device *parent, resource_size_t base,
- int irq, int *dma_rx_cfg, int *dma_tx_cfg);
-#endif
#include <plat/ste_dma40.h>
#include <mach/hardware.h>
-#include <mach/usb.h>
+#include <linux/platform_data/usb-musb-ux500.h>
#define MUSB_DMA40_RX_CH { \
.mode = STEDMA40_MODE_LOGICAL, \
#include <asm/mach/arch.h>
-#include <mach/vt8500fb.h>
+#include <linux/platform_data/video-vt8500lcdfb.h>
#include <mach/i8042.h>
#include "devices.h"
+++ /dev/null
-/*
- * VT8500/WM8505 Frame Buffer platform data definitions
- *
- * Copyright (C) 2010 Ed Spiridonov <edo.rus@gmail.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef _VT8500FB_H
-#define _VT8500FB_H
-
-#include <linux/fb.h>
-
-struct vt8500fb_platform_data {
- struct fb_videomode mode;
- u32 xres_virtual;
- u32 yres_virtual;
- u32 bpp;
- unsigned long video_mem_phys;
- void *video_mem_virt;
- unsigned long video_mem_len;
-};
-
-#endif /* _VT8500FB_H */
#include <asm/mach-types.h>
#include <mach/regs-serial.h>
-#include <mach/nuc900_spi.h>
+#include <linux/platform_data/spi-nuc900.h>
#include <mach/map.h>
-#include <mach/fb.h>
+#include <linux/platform_data/video-nuc900fb.h>
#include <mach/regs-ldm.h>
-#include <mach/w90p910_keypad.h>
+#include <linux/platform_data/keypad-w90p910.h>
#include "cpu.h"
+++ /dev/null
-/* linux/include/asm/arch-nuc900/fb.h
- *
- * Copyright (c) 2008 Nuvoton technology corporation
- * All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * Changelog:
- *
- * 2008/08/26 vincen.zswan modify this file for LCD.
- */
-
-#ifndef __ASM_ARM_FB_H
-#define __ASM_ARM_FB_H
-
-
-
-/* LCD Controller Hardware Desc */
-struct nuc900fb_hw {
- unsigned int lcd_dccs;
- unsigned int lcd_device_ctrl;
- unsigned int lcd_mpulcd_cmd;
- unsigned int lcd_int_cs;
- unsigned int lcd_crtc_size;
- unsigned int lcd_crtc_dend;
- unsigned int lcd_crtc_hr;
- unsigned int lcd_crtc_hsync;
- unsigned int lcd_crtc_vr;
- unsigned int lcd_va_baddr0;
- unsigned int lcd_va_baddr1;
- unsigned int lcd_va_fbctrl;
- unsigned int lcd_va_scale;
- unsigned int lcd_va_test;
- unsigned int lcd_va_win;
- unsigned int lcd_va_stuff;
-};
-
-/* LCD Display Description */
-struct nuc900fb_display {
- /* LCD Image type */
- unsigned type;
-
- /* LCD Screen Size */
- unsigned short width;
- unsigned short height;
-
- /* LCD Screen Info */
- unsigned short xres;
- unsigned short yres;
- unsigned short bpp;
-
- unsigned long pixclock;
- unsigned short left_margin;
- unsigned short right_margin;
- unsigned short hsync_len;
- unsigned short upper_margin;
- unsigned short lower_margin;
- unsigned short vsync_len;
-
- /* hardware special register value */
- unsigned int dccs;
- unsigned int devctl;
- unsigned int fbctrl;
- unsigned int scale;
-};
-
-struct nuc900fb_mach_info {
- struct nuc900fb_display *displays;
- unsigned num_displays;
- unsigned default_display;
- /* GPIO Setting Info */
- unsigned gpio_dir;
- unsigned gpio_dir_mask;
- unsigned gpio_data;
- unsigned gpio_data_mask;
-};
-
-extern void __init nuc900_fb_set_platdata(struct nuc900fb_mach_info *);
-
-#endif /* __ASM_ARM_FB_H */
+++ /dev/null
-#ifndef __ASM_ARCH_NUC900_I2C_H
-#define __ASM_ARCH_NUC900_I2C_H
-
-struct nuc900_platform_i2c {
- int bus_num;
- unsigned long bus_freq;
-};
-
-#endif /* __ASM_ARCH_NUC900_I2C_H */
+++ /dev/null
-/*
- * arch/arm/mach-w90x900/include/mach/nuc900_spi.h
- *
- * Copyright (c) 2009 Nuvoton technology corporation.
- *
- * Wan ZongShun <mcuos.com@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation;version 2 of the License.
- *
- */
-
-#ifndef __ASM_ARCH_SPI_H
-#define __ASM_ARCH_SPI_H
-
-extern void mfp_set_groupg(struct device *dev, const char *subname);
-
-struct nuc900_spi_info {
- unsigned int num_cs;
- unsigned int lsb;
- unsigned int txneg;
- unsigned int rxneg;
- unsigned int divider;
- unsigned int sleep;
- unsigned int txnum;
- unsigned int txbitlen;
- int bus_num;
-};
-
-struct nuc900_spi_chip {
- unsigned char bits_per_word;
-};
-
-#endif /* __ASM_ARCH_SPI_H */
+++ /dev/null
-#ifndef __ASM_ARCH_W90P910_KEYPAD_H
-#define __ASM_ARCH_W90P910_KEYPAD_H
-
-#include <linux/input/matrix_keypad.h>
-
-extern void mfp_set_groupi(struct device *dev);
-
-struct w90p910_keypad_platform_data {
- const struct matrix_keymap_data *keymap_data;
-
- unsigned int prescale;
- unsigned int debounce;
-};
-
-#endif /* __ASM_ARCH_W90P910_KEYPAD_H */
#include <asm/mach/map.h>
#include <asm/mach-types.h>
#include <mach/map.h>
-#include <mach/fb.h>
+#include <linux/platform_data/video-nuc900fb.h>
#include "nuc950.h"
#include <mach/hardware.h>
#include <mach/devices-common.h>
-#include <mach/esdhc.h>
+#include <linux/platform_data/mmc-esdhc-imx.h>
#define imx_sdhci_esdhc_imx_data_entry_single(soc, _devid, _id, hwid) \
{ \
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/init.h>
-#include <mach/sdma.h>
+#include <linux/platform_data/dma-imx-sdma.h>
extern struct device mxc_aips_bus;
extern struct device mxc_ahb_bus;
struct platform_device *__init imx_add_gpio_keys(
const struct gpio_keys_platform_data *pdata);
-#include <mach/mx21-usbhost.h>
+#include <linux/platform_data/usb-mx2.h>
struct imx_imx21_hcd_data {
resource_size_t iobase;
resource_size_t irq;
struct platform_device *__init imx_add_imxdi_rtc(
const struct imx_imxdi_rtc_data *data);
-#include <mach/imxfb.h>
+#include <linux/platform_data/video-imxfb.h>
struct imx_imx_fb_data {
resource_size_t iobase;
resource_size_t iosize;
const struct imx_imx_fb_data *data,
const struct imx_fb_platform_data *pdata);
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-imx.h>
struct imx_imx_i2c_data {
int id;
resource_size_t iobase;
const struct imx_imx_keypad_data *data,
const struct matrix_keymap_data *pdata);
-#include <mach/ssi.h>
+#include <linux/platform_data/asoc-imx-ssi.h>
struct imx_imx_ssi_data {
int id;
resource_size_t iobase;
const struct imx_imx_ssi_data *data,
const struct imx_ssi_platform_data *pdata);
-#include <mach/imx-uart.h>
+#include <linux/platform_data/serial-imx.h>
struct imx_imx_uart_3irq_data {
int id;
resource_size_t iobase;
const struct imx_imx_uart_1irq_data *data,
const struct imxuart_platform_data *pdata);
-#include <mach/usb.h>
+#include <linux/platform_data/usb-imx_udc.h>
struct imx_imx_udc_data {
resource_size_t iobase;
resource_size_t iosize;
const struct imx_imx_udc_data *data,
const struct imxusb_platform_data *pdata);
-#include <mach/mx3fb.h>
-#include <mach/mx3_camera.h>
+#include <linux/platform_data/video-mx3fb.h>
+#include <linux/platform_data/camera-mx3.h>
struct imx_ipu_core_data {
resource_size_t iobase;
resource_size_t synirq;
const struct imx_ipu_core_data *data,
struct mx3fb_platform_data *pdata);
-#include <mach/mx1_camera.h>
+#include <linux/platform_data/camera-mx1.h>
struct imx_mx1_camera_data {
resource_size_t iobase;
resource_size_t iosize;
const struct imx_mx1_camera_data *data,
const struct mx1_camera_pdata *pdata);
-#include <mach/mx2_cam.h>
+#include <linux/platform_data/camera-mx2.h>
struct imx_mx2_camera_data {
resource_size_t iobasecsi;
resource_size_t iosizecsi;
struct platform_device *__init imx_add_mx2_emmaprp(
const struct imx_mx2_camera_data *data);
-#include <mach/mxc_ehci.h>
+#include <linux/platform_data/usb-ehci-mxc.h>
struct imx_mxc_ehci_data {
int id;
resource_size_t iobase;
const struct imx_mxc_ehci_data *data,
const struct mxc_usbh_platform_data *pdata);
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-mxcmmc.h>
struct imx_mxc_mmc_data {
int id;
resource_size_t iobase;
const struct imx_mxc_mmc_data *data,
const struct imxmmc_platform_data *pdata);
-#include <mach/mxc_nand.h>
+#include <linux/platform_data/mtd-mxc_nand.h>
struct imx_mxc_nand_data {
/*
* id is traditionally 0, but -1 is more appropriate. We use -1 for new
struct platform_device *__init imx_add_mxc_w1(
const struct imx_mxc_w1_data *data);
-#include <mach/esdhc.h>
+#include <linux/platform_data/mmc-esdhc-imx.h>
struct imx_sdhci_esdhc_imx_data {
const char *devid;
int id;
const struct imx_sdhci_esdhc_imx_data *data,
const struct esdhc_platform_data *pdata);
-#include <mach/spi.h>
+#include <linux/platform_data/spi-imx.h>
struct imx_spi_imx_data {
const char *devid;
int id;
+++ /dev/null
-/*
- * Copyright 2004-2009 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_MXC_DMA_H__
-#define __ASM_ARCH_MXC_DMA_H__
-
-#include <linux/scatterlist.h>
-#include <linux/device.h>
-#include <linux/dmaengine.h>
-
-/*
- * This enumerates peripheral types. Used for SDMA.
- */
-enum sdma_peripheral_type {
- IMX_DMATYPE_SSI, /* MCU domain SSI */
- IMX_DMATYPE_SSI_SP, /* Shared SSI */
- IMX_DMATYPE_MMC, /* MMC */
- IMX_DMATYPE_SDHC, /* SDHC */
- IMX_DMATYPE_UART, /* MCU domain UART */
- IMX_DMATYPE_UART_SP, /* Shared UART */
- IMX_DMATYPE_FIRI, /* FIRI */
- IMX_DMATYPE_CSPI, /* MCU domain CSPI */
- IMX_DMATYPE_CSPI_SP, /* Shared CSPI */
- IMX_DMATYPE_SIM, /* SIM */
- IMX_DMATYPE_ATA, /* ATA */
- IMX_DMATYPE_CCM, /* CCM */
- IMX_DMATYPE_EXT, /* External peripheral */
- IMX_DMATYPE_MSHC, /* Memory Stick Host Controller */
- IMX_DMATYPE_MSHC_SP, /* Shared Memory Stick Host Controller */
- IMX_DMATYPE_DSP, /* DSP */
- IMX_DMATYPE_MEMORY, /* Memory */
- IMX_DMATYPE_FIFO_MEMORY,/* FIFO type Memory */
- IMX_DMATYPE_SPDIF, /* SPDIF */
- IMX_DMATYPE_IPU_MEMORY, /* IPU Memory */
- IMX_DMATYPE_ASRC, /* ASRC */
- IMX_DMATYPE_ESAI, /* ESAI */
-};
-
-enum imx_dma_prio {
- DMA_PRIO_HIGH = 0,
- DMA_PRIO_MEDIUM = 1,
- DMA_PRIO_LOW = 2
-};
-
-struct imx_dma_data {
- int dma_request; /* DMA request line */
- enum sdma_peripheral_type peripheral_type;
- int priority;
-};
-
-static inline int imx_dma_is_ipu(struct dma_chan *chan)
-{
- return !strcmp(dev_name(chan->device->dev), "ipu-core");
-}
-
-static inline int imx_dma_is_general_purpose(struct dma_chan *chan)
-{
- return strstr(dev_name(chan->device->dev), "sdma") ||
- !strcmp(dev_name(chan->device->dev), "imx-dma");
-}
-
-#endif
+++ /dev/null
-/*
- * Copyright 2010 Wolfram Sang <w.sang@pengutronix.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; version 2
- * of the License.
- */
-
-#ifndef __ASM_ARCH_IMX_ESDHC_H
-#define __ASM_ARCH_IMX_ESDHC_H
-
-enum wp_types {
- ESDHC_WP_NONE, /* no WP, neither controller nor gpio */
- ESDHC_WP_CONTROLLER, /* mmc controller internal WP */
- ESDHC_WP_GPIO, /* external gpio pin for WP */
-};
-
-enum cd_types {
- ESDHC_CD_NONE, /* no CD, neither controller nor gpio */
- ESDHC_CD_CONTROLLER, /* mmc controller internal CD */
- ESDHC_CD_GPIO, /* external gpio pin for CD */
- ESDHC_CD_PERMANENT, /* no CD, card permanently wired to host */
-};
-
-/**
- * struct esdhc_platform_data - platform data for esdhc on i.MX
- *
- * ESDHC_WP(CD)_CONTROLLER type is not available on i.MX25/35.
- *
- * @wp_gpio: gpio for write_protect
- * @cd_gpio: gpio for card_detect interrupt
- * @wp_type: type of write_protect method (see wp_types enum above)
- * @cd_type: type of card_detect method (see cd_types enum above)
- */
-
-struct esdhc_platform_data {
- unsigned int wp_gpio;
- unsigned int cd_gpio;
- enum wp_types wp_type;
- enum cd_types cd_type;
-};
-#endif /* __ASM_ARCH_IMX_ESDHC_H */
+++ /dev/null
-/*
- * i2c.h - i.MX I2C driver header file
- *
- * Copyright (c) 2008, Darius Augulis <augulis.darius@gmail.com>
- *
- * This file is released under the GPLv2
- */
-
-#ifndef __ASM_ARCH_I2C_H_
-#define __ASM_ARCH_I2C_H_
-
-/**
- * struct imxi2c_platform_data - structure of platform data for MXC I2C driver
- * @bitrate: Bus speed measured in Hz
- *
- **/
-struct imxi2c_platform_data {
- u32 bitrate;
-};
-
-#endif /* __ASM_ARCH_I2C_H_ */
+++ /dev/null
-/*
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#ifndef ASMARM_ARCH_UART_H
-#define ASMARM_ARCH_UART_H
-
-#define IMXUART_HAVE_RTSCTS (1<<0)
-#define IMXUART_IRDA (1<<1)
-
-struct imxuart_platform_data {
- int (*init)(struct platform_device *pdev);
- void (*exit)(struct platform_device *pdev);
- unsigned int flags;
- void (*irda_enable)(int enable);
- unsigned int irda_inv_rx:1;
- unsigned int irda_inv_tx:1;
- unsigned short transceiver_delay;
-};
-
-#endif
+++ /dev/null
-/*
- * This structure describes the machine which we are running on.
- */
-#ifndef __MACH_IMXFB_H__
-#define __MACH_IMXFB_H__
-
-#include <linux/fb.h>
-
-#define PCR_TFT (1 << 31)
-#define PCR_COLOR (1 << 30)
-#define PCR_PBSIZ_1 (0 << 28)
-#define PCR_PBSIZ_2 (1 << 28)
-#define PCR_PBSIZ_4 (2 << 28)
-#define PCR_PBSIZ_8 (3 << 28)
-#define PCR_BPIX_1 (0 << 25)
-#define PCR_BPIX_2 (1 << 25)
-#define PCR_BPIX_4 (2 << 25)
-#define PCR_BPIX_8 (3 << 25)
-#define PCR_BPIX_12 (4 << 25)
-#define PCR_BPIX_16 (5 << 25)
-#define PCR_BPIX_18 (6 << 25)
-#define PCR_PIXPOL (1 << 24)
-#define PCR_FLMPOL (1 << 23)
-#define PCR_LPPOL (1 << 22)
-#define PCR_CLKPOL (1 << 21)
-#define PCR_OEPOL (1 << 20)
-#define PCR_SCLKIDLE (1 << 19)
-#define PCR_END_SEL (1 << 18)
-#define PCR_END_BYTE_SWAP (1 << 17)
-#define PCR_REV_VS (1 << 16)
-#define PCR_ACD_SEL (1 << 15)
-#define PCR_ACD(x) (((x) & 0x7f) << 8)
-#define PCR_SCLK_SEL (1 << 7)
-#define PCR_SHARP (1 << 6)
-#define PCR_PCD(x) ((x) & 0x3f)
-
-#define PWMR_CLS(x) (((x) & 0x1ff) << 16)
-#define PWMR_LDMSK (1 << 15)
-#define PWMR_SCR1 (1 << 10)
-#define PWMR_SCR0 (1 << 9)
-#define PWMR_CC_EN (1 << 8)
-#define PWMR_PW(x) ((x) & 0xff)
-
-#define LSCR1_PS_RISE_DELAY(x) (((x) & 0x7f) << 26)
-#define LSCR1_CLS_RISE_DELAY(x) (((x) & 0x3f) << 16)
-#define LSCR1_REV_TOGGLE_DELAY(x) (((x) & 0xf) << 8)
-#define LSCR1_GRAY2(x) (((x) & 0xf) << 4)
-#define LSCR1_GRAY1(x) (((x) & 0xf))
-
-#define DMACR_BURST (1 << 31)
-#define DMACR_HM(x) (((x) & 0xf) << 16)
-#define DMACR_TM(x) ((x) & 0xf)
-
-struct imx_fb_videomode {
- struct fb_videomode mode;
- u32 pcr;
- unsigned char bpp;
-};
-
-struct imx_fb_platform_data {
- struct imx_fb_videomode *mode;
- int num_modes;
-
- u_int cmap_greyscale:1,
- cmap_inverse:1,
- cmap_static:1,
- unused:29;
-
- u_int pwmr;
- u_int lscr1;
- u_int dmacr;
-
- u_char * fixed_screen_cpu;
- dma_addr_t fixed_screen_dma;
-
- int (*init)(struct platform_device *);
- void (*exit)(struct platform_device *);
-
- void (*lcd_power)(int);
- void (*backlight_power)(int);
-};
-
-void set_imx_fb_info(struct imx_fb_platform_data *);
-#endif /* ifndef __MACH_IMXFB_H__ */
+++ /dev/null
-#ifndef ASMARM_ARCH_MMC_H
-#define ASMARM_ARCH_MMC_H
-
-#include <linux/mmc/host.h>
-
-struct device;
-
-/* board specific SDHC data, optional.
- * If not present, a writable card with 3,3V is assumed.
- */
-struct imxmmc_platform_data {
- /* Return values for the get_ro callback should be:
- * 0 for a read/write card
- * 1 for a read-only card
- * -ENOSYS when not supported (equal to NULL callback)
- * or a negative errno value when something bad happened
- */
- int (*get_ro)(struct device *);
-
- /* board specific hook to (de)initialize the SD slot.
- * The board code can call 'handler' on a card detection
- * change giving data as argument.
- */
- int (*init)(struct device *dev, irq_handler_t handler, void *data);
- void (*exit)(struct device *dev, void *data);
-
- /* available voltages. If not given, assume
- * MMC_VDD_32_33 | MMC_VDD_33_34
- */
- unsigned int ocr_avail;
-
- /* adjust slot voltage */
- void (*setpower)(struct device *, unsigned int vdd);
-
- /* enable card detect using DAT3 */
- int dat3_card_detect;
-};
-
-#endif
+++ /dev/null
-/*
- * mx1_camera.h - i.MX1/i.MXL camera driver header file
- *
- * Copyright (c) 2008, Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
- * Copyright (C) 2009, Darius Augulis <augulis.darius@gmail.com>
- *
- * Based on PXA camera.h file:
- * Copyright (C) 2003, Intel Corporation
- * Copyright (C) 2008, Guennadi Liakhovetski <kernel@pengutronix.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_CAMERA_H_
-#define __ASM_ARCH_CAMERA_H_
-
-#define MX1_CAMERA_DATA_HIGH 1
-#define MX1_CAMERA_PCLK_RISING 2
-#define MX1_CAMERA_VSYNC_HIGH 4
-
-extern unsigned char mx1_camera_sof_fiq_start, mx1_camera_sof_fiq_end;
-
-/**
- * struct mx1_camera_pdata - i.MX1/i.MXL camera platform data
- * @mclk_10khz: master clock frequency in 10kHz units
- * @flags: MX1 camera platform flags
- */
-struct mx1_camera_pdata {
- unsigned long mclk_10khz;
- unsigned long flags;
-};
-
-#endif /* __ASM_ARCH_CAMERA_H_ */
+++ /dev/null
-/*
- * Copyright (C) 2009 Martin Fuzzey <mfuzzey@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_MX21_USBH
-#define __ASM_ARCH_MX21_USBH
-
-enum mx21_usbh_xcvr {
- /* Values below as used by hardware (HWMODE register) */
- MX21_USBXCVR_TXDIF_RXDIF = 0,
- MX21_USBXCVR_TXDIF_RXSE = 1,
- MX21_USBXCVR_TXSE_RXDIF = 2,
- MX21_USBXCVR_TXSE_RXSE = 3,
-};
-
-struct mx21_usbh_platform_data {
- enum mx21_usbh_xcvr host_xcvr; /* tranceiver mode host 1,2 ports */
- enum mx21_usbh_xcvr otg_xcvr; /* tranceiver mode otg (as host) port */
- u16 enable_host1:1,
- enable_host2:1,
- enable_otg_host:1, /* enable "OTG" port (as host) */
- host1_xcverless:1, /* traceiverless host1 port */
- host1_txenoe:1, /* output enable host1 transmit enable */
- otg_ext_xcvr:1, /* external tranceiver for OTG port */
- unused:10;
-};
-
-#endif /* __ASM_ARCH_MX21_USBH */
+++ /dev/null
-/*
- * mx2-cam.h - i.MX27/i.MX25 camera driver header file
- *
- * Copyright (C) 2003, Intel Corporation
- * Copyright (C) 2008, Sascha Hauer <s.hauer@pengutronix.de>
- * Copyright (C) 2010, Baruch Siach <baruch@tkos.co.il>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
- */
-
-#ifndef __MACH_MX2_CAM_H_
-#define __MACH_MX2_CAM_H_
-
-#define MX2_CAMERA_SWAP16 (1 << 0)
-#define MX2_CAMERA_EXT_VSYNC (1 << 1)
-#define MX2_CAMERA_CCIR (1 << 2)
-#define MX2_CAMERA_CCIR_INTERLACE (1 << 3)
-#define MX2_CAMERA_HSYNC_HIGH (1 << 4)
-#define MX2_CAMERA_GATED_CLOCK (1 << 5)
-#define MX2_CAMERA_INV_DATA (1 << 6)
-#define MX2_CAMERA_PCLK_SAMPLE_RISING (1 << 7)
-#define MX2_CAMERA_PACK_DIR_MSB (1 << 8)
-
-/**
- * struct mx2_camera_platform_data - optional platform data for mx2_camera
- * @flags: any combination of MX2_CAMERA_*
- * @clk: clock rate of the csi block / 2
- */
-struct mx2_camera_platform_data {
- unsigned long flags;
- unsigned long clk;
-};
-
-#endif /* __MACH_MX2_CAM_H_ */
+++ /dev/null
-/*
- * mx3_camera.h - i.MX3x camera driver header file
- *
- * Copyright (C) 2008, Guennadi Liakhovetski, DENX Software Engineering, <lg@denx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef _MX3_CAMERA_H_
-#define _MX3_CAMERA_H_
-
-#include <linux/device.h>
-
-#define MX3_CAMERA_CLK_SRC 1
-#define MX3_CAMERA_EXT_VSYNC 2
-#define MX3_CAMERA_DP 4
-#define MX3_CAMERA_PCP 8
-#define MX3_CAMERA_HSP 0x10
-#define MX3_CAMERA_VSP 0x20
-#define MX3_CAMERA_DATAWIDTH_4 0x40
-#define MX3_CAMERA_DATAWIDTH_8 0x80
-#define MX3_CAMERA_DATAWIDTH_10 0x100
-#define MX3_CAMERA_DATAWIDTH_15 0x200
-
-#define MX3_CAMERA_DATAWIDTH_MASK (MX3_CAMERA_DATAWIDTH_4 | MX3_CAMERA_DATAWIDTH_8 | \
- MX3_CAMERA_DATAWIDTH_10 | MX3_CAMERA_DATAWIDTH_15)
-
-/**
- * struct mx3_camera_pdata - i.MX3x camera platform data
- * @flags: MX3_CAMERA_* flags
- * @mclk_10khz: master clock frequency in 10kHz units
- * @dma_dev: IPU DMA device to match against in channel allocation
- */
-struct mx3_camera_pdata {
- unsigned long flags;
- unsigned long mclk_10khz;
- struct device *dma_dev;
-};
-
-#endif
+++ /dev/null
-/*
- * Copyright (C) 2008
- * Guennadi Liakhovetski, DENX Software Engineering, <lg@denx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_MX3FB_H__
-#define __ASM_ARCH_MX3FB_H__
-
-#include <linux/device.h>
-#include <linux/fb.h>
-
-/* Proprietary FB_SYNC_ flags */
-#define FB_SYNC_OE_ACT_HIGH 0x80000000
-#define FB_SYNC_CLK_INVERT 0x40000000
-#define FB_SYNC_DATA_INVERT 0x20000000
-#define FB_SYNC_CLK_IDLE_EN 0x10000000
-#define FB_SYNC_SHARP_MODE 0x08000000
-#define FB_SYNC_SWAP_RGB 0x04000000
-#define FB_SYNC_CLK_SEL_EN 0x02000000
-
-/*
- * Specify the way your display is connected. The IPU can arbitrarily
- * map the internal colors to the external data lines. We only support
- * the following mappings at the moment.
- */
-enum disp_data_mapping {
- /* blue -> d[0..5], green -> d[6..11], red -> d[12..17] */
- IPU_DISP_DATA_MAPPING_RGB666,
- /* blue -> d[0..4], green -> d[5..10], red -> d[11..15] */
- IPU_DISP_DATA_MAPPING_RGB565,
- /* blue -> d[0..7], green -> d[8..15], red -> d[16..23] */
- IPU_DISP_DATA_MAPPING_RGB888,
-};
-
-/**
- * struct mx3fb_platform_data - mx3fb platform data
- *
- * @dma_dev: pointer to the dma-device, used for dma-slave connection
- * @mode: pointer to a platform-provided per mxc_register_fb() videomode
- */
-struct mx3fb_platform_data {
- struct device *dma_dev;
- const char *name;
- const struct fb_videomode *mode;
- int num_modes;
- enum disp_data_mapping disp_data_fmt;
-};
-
-#endif
+++ /dev/null
-#ifndef __INCLUDE_ASM_ARCH_MXC_EHCI_H
-#define __INCLUDE_ASM_ARCH_MXC_EHCI_H
-
-/* values for portsc field */
-#define MXC_EHCI_PHY_LOW_POWER_SUSPEND (1 << 23)
-#define MXC_EHCI_FORCE_FS (1 << 24)
-#define MXC_EHCI_UTMI_8BIT (0 << 28)
-#define MXC_EHCI_UTMI_16BIT (1 << 28)
-#define MXC_EHCI_SERIAL (1 << 29)
-#define MXC_EHCI_MODE_UTMI (0 << 30)
-#define MXC_EHCI_MODE_PHILIPS (1 << 30)
-#define MXC_EHCI_MODE_ULPI (2 << 30)
-#define MXC_EHCI_MODE_SERIAL (3 << 30)
-
-/* values for flags field */
-#define MXC_EHCI_INTERFACE_DIFF_UNI (0 << 0)
-#define MXC_EHCI_INTERFACE_DIFF_BI (1 << 0)
-#define MXC_EHCI_INTERFACE_SINGLE_UNI (2 << 0)
-#define MXC_EHCI_INTERFACE_SINGLE_BI (3 << 0)
-#define MXC_EHCI_INTERFACE_MASK (0xf)
-
-#define MXC_EHCI_POWER_PINS_ENABLED (1 << 5)
-#define MXC_EHCI_PWR_PIN_ACTIVE_HIGH (1 << 6)
-#define MXC_EHCI_OC_PIN_ACTIVE_LOW (1 << 7)
-#define MXC_EHCI_TTL_ENABLED (1 << 8)
-
-#define MXC_EHCI_INTERNAL_PHY (1 << 9)
-#define MXC_EHCI_IPPUE_DOWN (1 << 10)
-#define MXC_EHCI_IPPUE_UP (1 << 11)
-#define MXC_EHCI_WAKEUP_ENABLED (1 << 12)
-#define MXC_EHCI_ITC_NO_THRESHOLD (1 << 13)
-
-#define MXC_USBCTRL_OFFSET 0
-#define MXC_USB_PHY_CTR_FUNC_OFFSET 0x8
-#define MXC_USB_PHY_CTR_FUNC2_OFFSET 0xc
-#define MXC_USBH2CTRL_OFFSET 0x14
-
-#define MX5_USBOTHER_REGS_OFFSET 0x800
-
-/* USB_PHY_CTRL_FUNC2*/
-#define MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK 0x3
-#define MX5_USB_UTMI_PHYCTRL1_PLLDIV_SHIFT 0
-
-struct mxc_usbh_platform_data {
- int (*init)(struct platform_device *pdev);
- int (*exit)(struct platform_device *pdev);
-
- unsigned int portsc;
- struct usb_phy *otg;
-};
-
-int mx51_initialize_usb_hw(int port, unsigned int flags);
-int mx25_initialize_usb_hw(int port, unsigned int flags);
-int mx31_initialize_usb_hw(int port, unsigned int flags);
-int mx35_initialize_usb_hw(int port, unsigned int flags);
-int mx27_initialize_usb_hw(int port, unsigned int flags);
-
-#endif /* __INCLUDE_ASM_ARCH_MXC_EHCI_H */
-
+++ /dev/null
-/*
- * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2008 Sascha Hauer, kernel@pengutronix.de
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#ifndef __ASM_ARCH_NAND_H
-#define __ASM_ARCH_NAND_H
-
-#include <linux/mtd/partitions.h>
-
-struct mxc_nand_platform_data {
- unsigned int width; /* data bus width in bytes */
- unsigned int hw_ecc:1; /* 0 if suppress hardware ECC */
- unsigned int flash_bbt:1; /* set to 1 to use a flash based bbt */
- struct mtd_partition *parts; /* partition table */
- int nr_parts; /* size of parts */
-};
-#endif /* __ASM_ARCH_NAND_H */
+++ /dev/null
-#ifndef __MACH_MXC_SDMA_H__
-#define __MACH_MXC_SDMA_H__
-
-/**
- * struct sdma_script_start_addrs - SDMA script start pointers
- *
- * start addresses of the different functions in the physical
- * address space of the SDMA engine.
- */
-struct sdma_script_start_addrs {
- s32 ap_2_ap_addr;
- s32 ap_2_bp_addr;
- s32 ap_2_ap_fixed_addr;
- s32 bp_2_ap_addr;
- s32 loopback_on_dsp_side_addr;
- s32 mcu_interrupt_only_addr;
- s32 firi_2_per_addr;
- s32 firi_2_mcu_addr;
- s32 per_2_firi_addr;
- s32 mcu_2_firi_addr;
- s32 uart_2_per_addr;
- s32 uart_2_mcu_addr;
- s32 per_2_app_addr;
- s32 mcu_2_app_addr;
- s32 per_2_per_addr;
- s32 uartsh_2_per_addr;
- s32 uartsh_2_mcu_addr;
- s32 per_2_shp_addr;
- s32 mcu_2_shp_addr;
- s32 ata_2_mcu_addr;
- s32 mcu_2_ata_addr;
- s32 app_2_per_addr;
- s32 app_2_mcu_addr;
- s32 shp_2_per_addr;
- s32 shp_2_mcu_addr;
- s32 mshc_2_mcu_addr;
- s32 mcu_2_mshc_addr;
- s32 spdif_2_mcu_addr;
- s32 mcu_2_spdif_addr;
- s32 asrc_2_mcu_addr;
- s32 ext_mem_2_ipu_addr;
- s32 descrambler_addr;
- s32 dptc_dvfs_addr;
- s32 utra_addr;
- s32 ram_code_start_addr;
-};
-
-/**
- * struct sdma_platform_data - platform specific data for SDMA engine
- *
- * @fw_name The firmware name
- * @script_addrs SDMA scripts addresses in SDMA ROM
- */
-struct sdma_platform_data {
- char *fw_name;
- struct sdma_script_start_addrs *script_addrs;
-};
-
-#endif /* __MACH_MXC_SDMA_H__ */
+++ /dev/null
-
-#ifndef __MACH_SPI_H_
-#define __MACH_SPI_H_
-
-/*
- * struct spi_imx_master - device.platform_data for SPI controller devices.
- * @chipselect: Array of chipselects for this master. Numbers >= 0 mean gpio
- * pins, numbers < 0 mean internal CSPI chipselects according
- * to MXC_SPI_CS(). Normally you want to use gpio based chip
- * selects as the CSPI module tries to be intelligent about
- * when to assert the chipselect: The CSPI module deasserts the
- * chipselect once it runs out of input data. The other problem
- * is that it is not possible to mix between high active and low
- * active chipselects on one single bus using the internal
- * chipselects. Unfortunately Freescale decided to put some
- * chipselects on dedicated pins which are not usable as gpios,
- * so we have to support the internal chipselects.
- * @num_chipselect: ARRAY_SIZE(chipselect)
- */
-struct spi_imx_master {
- int *chipselect;
- int num_chipselect;
-};
-
-#define MXC_SPI_CS(no) ((no) - 32)
-
-#endif /* __MACH_SPI_H_*/
+++ /dev/null
-#ifndef __MACH_SSI_H
-#define __MACH_SSI_H
-
-struct snd_ac97;
-
-extern unsigned char imx_ssi_fiq_start, imx_ssi_fiq_end;
-extern unsigned long imx_ssi_fiq_base, imx_ssi_fiq_tx_buffer, imx_ssi_fiq_rx_buffer;
-
-struct imx_ssi_platform_data {
- unsigned int flags;
-#define IMX_SSI_DMA (1 << 0)
-#define IMX_SSI_USE_AC97 (1 << 1)
-#define IMX_SSI_NET (1 << 2)
-#define IMX_SSI_SYN (1 << 3)
-#define IMX_SSI_USE_I2S_SLAVE (1 << 4)
- void (*ac97_reset) (struct snd_ac97 *ac97);
- void (*ac97_warm_reset)(struct snd_ac97 *ac97);
-};
-
-#endif /* __MACH_SSI_H */
-
+++ /dev/null
-/*
- * Copyright (C) 2008 Darius Augulis <augulis.darius@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_MXC_USB
-#define __ASM_ARCH_MXC_USB
-
-struct imxusb_platform_data {
- int (*init)(struct device *);
- void (*exit)(struct device *);
-};
-
-#endif /* __ASM_ARCH_MXC_USB */
#include <linux/module.h>
-#include <mach/ssi.h>
+#include <linux/platform_data/asoc-imx-ssi.h>
EXPORT_SYMBOL(imx_ssi_fiq_tx_buffer);
EXPORT_SYMBOL(imx_ssi_fiq_rx_buffer);
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * License Terms: GNU General Public License v2
- * Author: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
- *
- * ux500 Scroll key and Keypad Encoder (SKE) header
- */
-
-#ifndef __SKE_H
-#define __SKE_H
-
-#include <linux/input/matrix_keypad.h>
-
-/* register definitions for SKE peripheral */
-#define SKE_CR 0x00
-#define SKE_VAL0 0x04
-#define SKE_VAL1 0x08
-#define SKE_DBCR 0x0C
-#define SKE_IMSC 0x10
-#define SKE_RIS 0x14
-#define SKE_MIS 0x18
-#define SKE_ICR 0x1C
-
-/*
- * Keypad module
- */
-
-/**
- * struct keypad_platform_data - structure for platform specific data
- * @init: pointer to keypad init function
- * @exit: pointer to keypad deinitialisation function
- * @keymap_data: matrix scan code table for keycodes
- * @krow: maximum number of rows
- * @kcol: maximum number of columns
- * @debounce_ms: platform specific debounce time
- * @no_autorepeat: flag for auto repetition
- * @wakeup_enable: allow waking up the system
- */
-struct ske_keypad_platform_data {
- int (*init)(void);
- int (*exit)(void);
- const struct matrix_keymap_data *keymap_data;
- u8 krow;
- u8 kcol;
- u8 debounce_ms;
- bool no_autorepeat;
- bool wakeup_enable;
-};
-#endif /*__SKE_KPD_H*/
#include <linux/mv643xx_eth.h>
#include <linux/mv643xx_i2c.h>
#include <net/dsa.h>
-#include <plat/mv_xor.h>
-#include <plat/ehci-orion.h>
+#include <linux/platform_data/dma-mv_xor.h>
+#include <linux/platform_data/usb-ehci-orion.h>
#include <mach/bridge-regs.h>
/* Create a clkdev entry for a given device/clk */
+++ /dev/null
-#ifndef __PLAT_AUDIO_H
-#define __PLAT_AUDIO_H
-
-struct kirkwood_asoc_platform_data {
- int burst;
-};
-#endif
+++ /dev/null
-/*
- * arch/arm/plat-orion/include/plat/ehci-orion.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_EHCI_ORION_H
-#define __PLAT_EHCI_ORION_H
-
-#include <linux/mbus.h>
-
-enum orion_ehci_phy_ver {
- EHCI_PHY_ORION,
- EHCI_PHY_DD,
- EHCI_PHY_KW,
- EHCI_PHY_NA,
-};
-
-struct orion_ehci_data {
- enum orion_ehci_phy_ver phy_version;
-};
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/plat-orion/include/plat/mv_xor.h
- *
- * Marvell XOR platform device data definition file.
- */
-
-#ifndef __PLAT_MV_XOR_H
-#define __PLAT_MV_XOR_H
-
-#include <linux/dmaengine.h>
-#include <linux/mbus.h>
-
-#define MV_XOR_SHARED_NAME "mv_xor_shared"
-#define MV_XOR_NAME "mv_xor"
-
-struct mv_xor_platform_data {
- struct platform_device *shared;
- int hw_id;
- dma_cap_mask_t cap_mask;
- size_t pool_size;
-};
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/plat-orion/include/plat/mvsdio.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_MVSDIO_H
-#define __MACH_MVSDIO_H
-
-#include <linux/mbus.h>
-
-struct mvsdio_platform_data {
- unsigned int clock;
- int gpio_card_detect;
- int gpio_write_protect;
-};
-
-#endif
+++ /dev/null
-/*
- * arch/arm/plat-orion/include/plat/orion_nand.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_ORION_NAND_H
-#define __PLAT_ORION_NAND_H
-
-/*
- * Device bus NAND private data
- */
-struct orion_nand_data {
- struct mtd_partition *parts;
- int (*dev_ready)(struct mtd_info *mtd);
- u32 nr_parts;
- u8 ale; /* address line number connected to ALE */
- u8 cle; /* address line number connected to CLE */
- u8 width; /* buswidth */
- u8 chip_delay;
-};
-
-
-#endif
+++ /dev/null
-#ifndef __ASM_ARCH_PXA27x_KEYPAD_H
-#define __ASM_ARCH_PXA27x_KEYPAD_H
-
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-
-#define MAX_MATRIX_KEY_ROWS (8)
-#define MAX_MATRIX_KEY_COLS (8)
-#define MATRIX_ROW_SHIFT (3)
-#define MAX_DIRECT_KEY_NUM (8)
-
-/* pxa3xx keypad platform specific parameters
- *
- * NOTE:
- * 1. direct_key_num indicates the number of keys in the direct keypad
- * _plus_ the number of rotary-encoder sensor inputs, this can be
- * left as 0 if only rotary encoders are enabled, the driver will
- * automatically calculate this
- *
- * 2. direct_key_map is the key code map for the direct keys, if rotary
- * encoder(s) are enabled, direct key 0/1(2/3) will be ignored
- *
- * 3. rotary can be either interpreted as a relative input event (e.g.
- * REL_WHEEL/REL_HWHEEL) or specific keys (e.g. UP/DOWN/LEFT/RIGHT)
- *
- * 4. matrix key and direct key will use the same debounce_interval by
- * default, which should be sufficient in most cases
- *
- * pxa168 keypad platform specific parameter
- *
- * NOTE:
- * clear_wakeup_event callback is a workaround required to clear the
- * keypad interrupt. The keypad wake must be cleared in addition to
- * reading the MI/DI bits in the KPC register.
- */
-struct pxa27x_keypad_platform_data {
-
- /* code map for the matrix keys */
- unsigned int matrix_key_rows;
- unsigned int matrix_key_cols;
- unsigned int *matrix_key_map;
- int matrix_key_map_size;
-
- /* direct keys */
- int direct_key_num;
- unsigned int direct_key_map[MAX_DIRECT_KEY_NUM];
- /* the key output may be low active */
- int direct_key_low_active;
- /* give board a chance to choose the start direct key */
- unsigned int direct_key_mask;
-
- /* rotary encoders 0 */
- int enable_rotary0;
- int rotary0_rel_code;
- int rotary0_up_key;
- int rotary0_down_key;
-
- /* rotary encoders 1 */
- int enable_rotary1;
- int rotary1_rel_code;
- int rotary1_up_key;
- int rotary1_down_key;
-
- /* key debounce interval */
- unsigned int debounce_interval;
-
- /* clear wakeup event requirement for pxa168 */
- void (*clear_wakeup_event)(void);
-};
-
-extern void pxa_set_keypad_info(struct pxa27x_keypad_platform_data *info);
-
-#endif /* __ASM_ARCH_PXA27x_KEYPAD_H */
+++ /dev/null
-#ifndef __ASM_ARCH_PXA3XX_NAND_H
-#define __ASM_ARCH_PXA3XX_NAND_H
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-
-struct pxa3xx_nand_timing {
- unsigned int tCH; /* Enable signal hold time */
- unsigned int tCS; /* Enable signal setup time */
- unsigned int tWH; /* ND_nWE high duration */
- unsigned int tWP; /* ND_nWE pulse time */
- unsigned int tRH; /* ND_nRE high duration */
- unsigned int tRP; /* ND_nRE pulse width */
- unsigned int tR; /* ND_nWE high to ND_nRE low for read */
- unsigned int tWHR; /* ND_nWE high to ND_nRE low for status read */
- unsigned int tAR; /* ND_ALE low to ND_nRE low delay */
-};
-
-struct pxa3xx_nand_cmdset {
- uint16_t read1;
- uint16_t read2;
- uint16_t program;
- uint16_t read_status;
- uint16_t read_id;
- uint16_t erase;
- uint16_t reset;
- uint16_t lock;
- uint16_t unlock;
- uint16_t lock_status;
-};
-
-struct pxa3xx_nand_flash {
- char *name;
- uint32_t chip_id;
- unsigned int page_per_block; /* Pages per block (PG_PER_BLK) */
- unsigned int page_size; /* Page size in bytes (PAGE_SZ) */
- unsigned int flash_width; /* Width of Flash memory (DWIDTH_M) */
- unsigned int dfc_width; /* Width of flash controller(DWIDTH_C) */
- unsigned int num_blocks; /* Number of physical blocks in Flash */
-
- struct pxa3xx_nand_timing *timing; /* NAND Flash timing */
-};
-
-/*
- * Current pxa3xx_nand controller has two chip select which
- * both be workable.
- *
- * Notice should be taken that:
- * When you want to use this feature, you should not enable the
- * keep configuration feature, for two chip select could be
- * attached with different nand chip. The different page size
- * and timing requirement make the keep configuration impossible.
- */
-
-/* The max num of chip select current support */
-#define NUM_CHIP_SELECT (2)
-struct pxa3xx_nand_platform_data {
-
- /* the data flash bus is shared between the Static Memory
- * Controller and the Data Flash Controller, the arbiter
- * controls the ownership of the bus
- */
- int enable_arbiter;
-
- /* allow platform code to keep OBM/bootloader defined NFC config */
- int keep_config;
-
- /* indicate how many chip selects will be used */
- int num_cs;
-
- const struct mtd_partition *parts[NUM_CHIP_SELECT];
- unsigned int nr_parts[NUM_CHIP_SELECT];
-
- const struct pxa3xx_nand_flash * flash;
- size_t num_flash;
-};
-
-extern void pxa3xx_set_nand_info(struct pxa3xx_nand_platform_data *info);
-#endif /* __ASM_ARCH_PXA3XX_NAND_H */
#include <plat/cpu.h>
#include <plat/devs.h>
#include <plat/adc.h>
-#include <plat/ata.h>
-#include <plat/ehci.h>
+#include <linux/platform_data/ata-samsung_cf.h>
+#include <linux/platform_data/usb-ehci-s5p.h>
#include <plat/fb.h>
#include <plat/fb-s3c2410.h>
-#include <plat/hwmon.h>
-#include <plat/iic.h>
+#include <linux/platform_data/hwmon-s3c.h>
+#include <linux/platform_data/i2c-s3c2410.h>
#include <plat/keypad.h>
-#include <plat/mci.h>
-#include <plat/nand.h>
+#include <linux/platform_data/mmc-s3cmci.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <plat/sdhci.h>
-#include <plat/ts.h>
-#include <plat/udc.h>
-#include <plat/usb-control.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/usb-ohci-s3c2410.h>
#include <plat/usb-phy.h>
#include <plat/regs-iic.h>
#include <plat/regs-serial.h>
#include <plat/regs-spi.h>
-#include <plat/s3c64xx-spi.h>
+#include <linux/platform_data/spi-s3c64xx.h>
static u64 samsung_device_dma_mask = DMA_BIT_MASK(32);
+++ /dev/null
-/* linux/arch/arm/plat-samsung/include/plat/ata.h
- *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * Samsung CF-ATA platform_device info
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_PLAT_ATA_H
-#define __ASM_PLAT_ATA_H __FILE__
-
-/**
- * struct s3c_ide_platdata - S3C IDE driver platform data.
- * @setup_gpio: Setup the external GPIO pins to the right state for data
- * transfer in true-ide mode.
- */
-struct s3c_ide_platdata {
- void (*setup_gpio)(void);
-};
-
-/*
- * s3c_ide_set_platdata() - Setup the platform specifc data for IDE driver.
- * @pdata: Platform data for IDE driver.
- */
-extern void s3c_ide_set_platdata(struct s3c_ide_platdata *pdata);
-
-/* architecture-specific IDE configuration */
-extern void s3c64xx_ide_setup_gpio(void);
-extern void s5pc100_ide_setup_gpio(void);
-extern void s5pv210_ide_setup_gpio(void);
-
-#endif /*__ASM_PLAT_ATA_H */
+++ /dev/null
-/* arch/arm/plat-samsung/include/plat/audio-simtec.h
- *
- * Copyright 2008 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- * Ben Dooks <ben@simtec.co.uk>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Simtec Audio support.
-*/
-
-/**
- * struct s3c24xx_audio_simtec_pdata - platform data for simtec audio
- * @use_mpllin: Select codec clock from MPLLin
- * @output_cdclk: Need to output CDCLK to the codec
- * @have_mic: Set if we have a MIC socket
- * @have_lout: Set if we have a LineOut socket
- * @amp_gpio: GPIO pin to enable the AMP
- * @amp_gain: Option GPIO to control AMP gain
- */
-struct s3c24xx_audio_simtec_pdata {
- unsigned int use_mpllin:1;
- unsigned int output_cdclk:1;
-
- unsigned int have_mic:1;
- unsigned int have_lout:1;
-
- int amp_gpio;
- int amp_gain[2];
-
- void (*startup)(void);
-};
+++ /dev/null
-/* arch/arm/plat-samsung/include/plat/audio.h
- *
- * Copyright (c) 2009 Samsung Electronics Co. Ltd
- * Author: Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-/* The machine init code calls s3c*_ac97_setup_gpio with
- * one of these defines in order to select appropriate bank
- * of GPIO for AC97 pins
- */
-#define S3C64XX_AC97_GPD 0
-#define S3C64XX_AC97_GPE 1
-extern void s3c64xx_ac97_setup_gpio(int);
-
-/*
- * The machine init code calls s5p*_spdif_setup_gpio with
- * one of these defines in order to select appropriate bank
- * of GPIO for S/PDIF pins
- */
-#define S5PC100_SPDIF_GPD 0
-#define S5PC100_SPDIF_GPG3 1
-extern void s5pc100_spdif_setup_gpio(int);
-
-struct samsung_i2s {
-/* If the Primary DAI has 5.1 Channels */
-#define QUIRK_PRI_6CHAN (1 << 0)
-/* If the I2S block has a Stereo Overlay Channel */
-#define QUIRK_SEC_DAI (1 << 1)
-/*
- * If the I2S block has no internal prescalar or MUX (I2SMOD[10] bit)
- * The Machine driver must provide suitably set clock to the I2S block.
- */
-#define QUIRK_NO_MUXPSR (1 << 2)
-#define QUIRK_NEED_RSTCLR (1 << 3)
- /* Quirks of the I2S controller */
- u32 quirks;
-
- /*
- * Array of clock names that can be used to generate I2S signals.
- * Also corresponds to clocks of I2SMOD[10]
- */
- const char **src_clk;
- dma_addr_t idma_addr;
-};
-
-/**
- * struct s3c_audio_pdata - common platform data for audio device drivers
- * @cfg_gpio: Callback function to setup mux'ed pins in I2S/PCM/AC97 mode
- */
-struct s3c_audio_pdata {
- int (*cfg_gpio)(struct platform_device *);
- union {
- struct samsung_i2s i2s;
- } type;
-};
+++ /dev/null
-/*
- * Copyright (C) 2011 Samsung Electronics Co.Ltd
- * Author: Joonyoung Shim <jy0922.shim@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef __PLAT_SAMSUNG_EHCI_H
-#define __PLAT_SAMSUNG_EHCI_H __FILE__
-
-struct s5p_ehci_platdata {
- int (*phy_init)(struct platform_device *pdev, int type);
- int (*phy_exit)(struct platform_device *pdev, int type);
-};
-
-extern void s5p_ehci_set_platdata(struct s5p_ehci_platdata *pd);
-
-#endif /* __PLAT_SAMSUNG_EHCI_H */
+++ /dev/null
-/* linux/arch/arm/plat-s3c/include/plat/hwmon.h
- *
- * Copyright 2005 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- * http://armlinux.simtec.co.uk/
- *
- * S3C - HWMon interface for ADC
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_ADC_HWMON_H
-#define __ASM_ARCH_ADC_HWMON_H __FILE__
-
-/**
- * s3c_hwmon_chcfg - channel configuration
- * @name: The name to give this channel.
- * @mult: Multiply the ADC value read by this.
- * @div: Divide the value from the ADC by this.
- *
- * The value read from the ADC is converted to a value that
- * hwmon expects (mV) by result = (value_read * @mult) / @div.
- */
-struct s3c_hwmon_chcfg {
- const char *name;
- unsigned int mult;
- unsigned int div;
-};
-
-/**
- * s3c_hwmon_pdata - HWMON platform data
- * @in: One configuration for each possible channel used.
- */
-struct s3c_hwmon_pdata {
- struct s3c_hwmon_chcfg *in[8];
-};
-
-/**
- * s3c_hwmon_set_platdata - Set platform data for S3C HWMON device
- * @pd: Platform data to register to device.
- *
- * Register the given platform data for use with the S3C HWMON device.
- * The call will copy the platform data, so the board definitions can
- * make the structure itself __initdata.
- */
-extern void __init s3c_hwmon_set_platdata(struct s3c_hwmon_pdata *pd);
-
-#endif /* __ASM_ARCH_ADC_HWMON_H */
-
+++ /dev/null
-/* arch/arm/plat-s3c/include/plat/iic.h
- *
- * Copyright 2004-2009 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C - I2C Controller platform_device info
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_IIC_H
-#define __ASM_ARCH_IIC_H __FILE__
-
-#define S3C_IICFLG_FILTER (1<<0) /* enable s3c2440 filter */
-
-/**
- * struct s3c2410_platform_i2c - Platform data for s3c I2C.
- * @bus_num: The bus number to use (if possible).
- * @flags: Any flags for the I2C bus (E.g. S3C_IICFLK_FILTER).
- * @slave_addr: The I2C address for the slave device (if enabled).
- * @frequency: The desired frequency in Hz of the bus. This is
- * guaranteed to not be exceeded. If the caller does
- * not care, use zero and the driver will select a
- * useful default.
- * @sda_delay: The delay (in ns) applied to SDA edges.
- * @cfg_gpio: A callback to configure the pins for I2C operation.
- */
-struct s3c2410_platform_i2c {
- int bus_num;
- unsigned int flags;
- unsigned int slave_addr;
- unsigned long frequency;
- unsigned int sda_delay;
-
- void (*cfg_gpio)(struct platform_device *dev);
-};
-
-/**
- * s3c_i2c0_set_platdata - set platform data for i2c0 device
- * @i2c: The platform data to set, or NULL for default data.
- *
- * Register the given platform data for use with the i2c0 device. This
- * call copies the platform data, so the caller can use __initdata for
- * their copy.
- *
- * This call will set cfg_gpio if is null to the default platform
- * implementation.
- *
- * Any user of s3c_device_i2c0 should call this, even if it is with
- * NULL to ensure that the device is given the default platform data
- * as the driver will no longer carry defaults.
- */
-extern void s3c_i2c0_set_platdata(struct s3c2410_platform_i2c *i2c);
-extern void s3c_i2c1_set_platdata(struct s3c2410_platform_i2c *i2c);
-extern void s3c_i2c2_set_platdata(struct s3c2410_platform_i2c *i2c);
-extern void s3c_i2c3_set_platdata(struct s3c2410_platform_i2c *i2c);
-extern void s3c_i2c4_set_platdata(struct s3c2410_platform_i2c *i2c);
-extern void s3c_i2c5_set_platdata(struct s3c2410_platform_i2c *i2c);
-extern void s3c_i2c6_set_platdata(struct s3c2410_platform_i2c *i2c);
-extern void s3c_i2c7_set_platdata(struct s3c2410_platform_i2c *i2c);
-extern void s5p_i2c_hdmiphy_set_platdata(struct s3c2410_platform_i2c *i2c);
-
-/* defined by architecture to configure gpio */
-extern void s3c_i2c0_cfg_gpio(struct platform_device *dev);
-extern void s3c_i2c1_cfg_gpio(struct platform_device *dev);
-extern void s3c_i2c2_cfg_gpio(struct platform_device *dev);
-extern void s3c_i2c3_cfg_gpio(struct platform_device *dev);
-extern void s3c_i2c4_cfg_gpio(struct platform_device *dev);
-extern void s3c_i2c5_cfg_gpio(struct platform_device *dev);
-extern void s3c_i2c6_cfg_gpio(struct platform_device *dev);
-extern void s3c_i2c7_cfg_gpio(struct platform_device *dev);
-
-extern struct s3c2410_platform_i2c default_i2c_data;
-
-#endif /* __ASM_ARCH_IIC_H */
+++ /dev/null
-#ifndef _ARCH_MCI_H
-#define _ARCH_MCI_H
-
-/**
- * struct s3c24xx_mci_pdata - sd/mmc controller platform data
- * @no_wprotect: Set this to indicate there is no write-protect switch.
- * @no_detect: Set this if there is no detect switch.
- * @wprotect_invert: Invert the default sense of the write protect switch.
- * @detect_invert: Invert the default sense of the write protect switch.
- * @use_dma: Set to allow the use of DMA.
- * @gpio_detect: GPIO number for the card detect line.
- * @gpio_wprotect: GPIO number for the write protect line.
- * @ocr_avail: The mask of the available power states, non-zero to use.
- * @set_power: Callback to control the power mode.
- *
- * The @gpio_detect is used for card detection when @no_wprotect is unset,
- * and the default sense is that 0 returned from gpio_get_value() means
- * that a card is inserted. If @detect_invert is set, then the value from
- * gpio_get_value() is inverted, which makes 1 mean card inserted.
- *
- * The driver will use @gpio_wprotect to signal whether the card is write
- * protected if @no_wprotect is not set. A 0 returned from gpio_get_value()
- * means the card is read/write, and 1 means read-only. The @wprotect_invert
- * will invert the value returned from gpio_get_value().
- *
- * Card power is set by @ocr_availa, using MCC_VDD_ constants if it is set
- * to a non-zero value, otherwise the default of 3.2-3.4V is used.
- */
-struct s3c24xx_mci_pdata {
- unsigned int no_wprotect:1;
- unsigned int no_detect:1;
- unsigned int wprotect_invert:1;
- unsigned int detect_invert:1; /* set => detect active high */
- unsigned int use_dma:1;
-
- unsigned int gpio_detect;
- unsigned int gpio_wprotect;
- unsigned long ocr_avail;
- void (*set_power)(unsigned char power_mode,
- unsigned short vdd);
-};
-
-/**
- * s3c24xx_mci_set_platdata - set platform data for mmc/sdi device
- * @pdata: The platform data
- *
- * Copy the platform data supplied by @pdata so that this can be marked
- * __initdata.
- */
-extern void s3c24xx_mci_set_platdata(struct s3c24xx_mci_pdata *pdata);
-
-#endif /* _ARCH_NCI_H */
+++ /dev/null
-/*
- * Copyright (C) 2010-2011 Samsung Electronics Co., Ltd.
- *
- * S5P series MIPI CSI slave device support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __PLAT_SAMSUNG_MIPI_CSIS_H_
-#define __PLAT_SAMSUNG_MIPI_CSIS_H_ __FILE__
-
-struct platform_device;
-
-/**
- * struct s5p_platform_mipi_csis - platform data for S5P MIPI-CSIS driver
- * @clk_rate: bus clock frequency
- * @lanes: number of data lanes used
- * @alignment: data alignment in bits
- * @hs_settle: HS-RX settle time
- * @fixed_phy_vdd: false to enable external D-PHY regulator management in the
- * driver or true in case this regulator has no enable function
- * @phy_enable: pointer to a callback controlling D-PHY enable/reset
- */
-struct s5p_platform_mipi_csis {
- unsigned long clk_rate;
- u8 lanes;
- u8 alignment;
- u8 hs_settle;
- bool fixed_phy_vdd;
- int (*phy_enable)(struct platform_device *pdev, bool on);
-};
-
-/**
- * s5p_csis_phy_enable - global MIPI-CSI receiver D-PHY control
- * @pdev: MIPI-CSIS platform device
- * @on: true to enable D-PHY and deassert its reset
- * false to disable D-PHY
- */
-int s5p_csis_phy_enable(struct platform_device *pdev, bool on);
-
-#endif /* __PLAT_SAMSUNG_MIPI_CSIS_H_ */
+++ /dev/null
-/* arch/arm/mach-s3c2410/include/mach/nand.h
- *
- * Copyright (c) 2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - NAND device controller platform_device info
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-/**
- * struct s3c2410_nand_set - define a set of one or more nand chips
- * @disable_ecc: Entirely disable ECC - Dangerous
- * @flash_bbt: Openmoko u-boot can create a Bad Block Table
- * Setting this flag will allow the kernel to
- * look for it at boot time and also skip the NAND
- * scan.
- * @options: Default value to set into 'struct nand_chip' options.
- * @nr_chips: Number of chips in this set
- * @nr_partitions: Number of partitions pointed to by @partitions
- * @name: Name of set (optional)
- * @nr_map: Map for low-layer logical to physical chip numbers (option)
- * @partitions: The mtd partition list
- *
- * define a set of one or more nand chips registered with an unique mtd. Also
- * allows to pass flag to the underlying NAND layer. 'disable_ecc' will trigger
- * a warning at boot time.
- */
-struct s3c2410_nand_set {
- unsigned int disable_ecc:1;
- unsigned int flash_bbt:1;
-
- unsigned int options;
- int nr_chips;
- int nr_partitions;
- char *name;
- int *nr_map;
- struct mtd_partition *partitions;
- struct nand_ecclayout *ecc_layout;
-};
-
-struct s3c2410_platform_nand {
- /* timing information for controller, all times in nanoseconds */
-
- int tacls; /* time for active CLE/ALE to nWE/nOE */
- int twrph0; /* active time for nWE/nOE */
- int twrph1; /* time for release CLE/ALE from nWE/nOE inactive */
-
- unsigned int ignore_unset_ecc:1;
-
- int nr_sets;
- struct s3c2410_nand_set *sets;
-
- void (*select_chip)(struct s3c2410_nand_set *,
- int chip);
-};
-
-/**
- * s3c_nand_set_platdata() - register NAND platform data.
- * @nand: The NAND platform data to register with s3c_device_nand.
- *
- * This function copies the given NAND platform data, @nand and registers
- * it with the s3c_device_nand. This allows @nand to be __initdata.
-*/
-extern void s3c_nand_set_platdata(struct s3c2410_platform_nand *nand);
+++ /dev/null
-/* linux/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
- *
- * Copyright (C) 2009 Samsung Electronics Ltd.
- * Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __S3C64XX_PLAT_SPI_H
-#define __S3C64XX_PLAT_SPI_H
-
-struct platform_device;
-
-/**
- * struct s3c64xx_spi_csinfo - ChipSelect description
- * @fb_delay: Slave specific feedback delay.
- * Refer to FB_CLK_SEL register definition in SPI chapter.
- * @line: Custom 'identity' of the CS line.
- *
- * This is per SPI-Slave Chipselect information.
- * Allocate and initialize one in machine init code and make the
- * spi_board_info.controller_data point to it.
- */
-struct s3c64xx_spi_csinfo {
- u8 fb_delay;
- unsigned line;
-};
-
-/**
- * struct s3c64xx_spi_info - SPI Controller defining structure
- * @src_clk_nr: Clock source index for the CLK_CFG[SPI_CLKSEL] field.
- * @num_cs: Number of CS this controller emulates.
- * @cfg_gpio: Configure pins for this SPI controller.
- */
-struct s3c64xx_spi_info {
- int src_clk_nr;
- int num_cs;
- int (*cfg_gpio)(void);
-};
-
-/**
- * s3c64xx_spi_set_platdata - SPI Controller configure callback by the board
- * initialization code.
- * @cfg_gpio: Pointer to gpio setup function.
- * @src_clk_nr: Clock the SPI controller is to use to generate SPI clocks.
- * @num_cs: Number of elements in the 'cs' array.
- *
- * Call this from machine init code for each SPI Controller that
- * has some chips attached to it.
- */
-extern void s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
- int num_cs);
-extern void s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
- int num_cs);
-extern void s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
- int num_cs);
-
-/* defined by architecture to configure gpio */
-extern int s3c64xx_spi0_cfg_gpio(void);
-extern int s3c64xx_spi1_cfg_gpio(void);
-extern int s3c64xx_spi2_cfg_gpio(void);
-
-extern struct s3c64xx_spi_info s3c64xx_spi0_pdata;
-extern struct s3c64xx_spi_info s3c64xx_spi1_pdata;
-extern struct s3c64xx_spi_info s3c64xx_spi2_pdata;
-#endif /* __S3C64XX_PLAT_SPI_H */
+++ /dev/null
-/* arch/arm/plat-samsung/include/plat/ts.h
- *
- * Copyright (c) 2005 Arnaud Patard <arnaud.patard@rtp-net.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARM_TS_H
-#define __ASM_ARM_TS_H
-
-struct s3c2410_ts_mach_info {
- int delay;
- int presc;
- int oversampling_shift;
- void (*cfg_gpio)(struct platform_device *dev);
-};
-
-extern void s3c24xx_ts_set_platdata(struct s3c2410_ts_mach_info *);
-
-/* defined by architecture to configure gpio */
-extern void s3c24xx_ts_cfg_gpio(struct platform_device *dev);
-
-#endif /* __ASM_ARM_TS_H */
+++ /dev/null
-/* arch/arm/plat-samsung/include/plat/udc.h
- *
- * Copyright (c) 2005 Arnaud Patard <arnaud.patard@rtp-net.org>
- *
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *
- * Changelog:
- * 14-Mar-2005 RTP Created file
- * 02-Aug-2005 RTP File rename
- * 07-Sep-2005 BJD Minor cleanups, changed cmd to enum
- * 18-Jan-2007 HMW Add per-platform vbus_draw function
-*/
-
-#ifndef __ASM_ARM_ARCH_UDC_H
-#define __ASM_ARM_ARCH_UDC_H
-
-enum s3c2410_udc_cmd_e {
- S3C2410_UDC_P_ENABLE = 1, /* Pull-up enable */
- S3C2410_UDC_P_DISABLE = 2, /* Pull-up disable */
- S3C2410_UDC_P_RESET = 3, /* UDC reset, in case of */
-};
-
-struct s3c2410_udc_mach_info {
- void (*udc_command)(enum s3c2410_udc_cmd_e);
- void (*vbus_draw)(unsigned int ma);
-
- unsigned int pullup_pin;
- unsigned int pullup_pin_inverted;
-
- unsigned int vbus_pin;
- unsigned char vbus_pin_inverted;
-};
-
-extern void __init s3c24xx_udc_set_platdata(struct s3c2410_udc_mach_info *);
-
-struct s3c24xx_hsudc_platdata;
-
-extern void __init s3c24xx_hsudc_set_platdata(struct s3c24xx_hsudc_platdata *pd);
-
-#endif /* __ASM_ARM_ARCH_UDC_H */
+++ /dev/null
-/* arch/arm/plat-samsung/include/plat/usb-control.h
- *
- * Copyright (c) 2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C - USB host port information
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_USBCONTROL_H
-#define __ASM_ARCH_USBCONTROL_H
-
-#define S3C_HCDFLG_USED (1)
-
-struct s3c2410_hcd_port {
- unsigned char flags;
- unsigned char power;
- unsigned char oc_status;
- unsigned char oc_changed;
-};
-
-struct s3c2410_hcd_info {
- struct usb_hcd *hcd;
- struct s3c2410_hcd_port port[2];
-
- void (*power_control)(int port, int to);
- void (*enable_oc)(struct s3c2410_hcd_info *, int on);
- void (*report_oc)(struct s3c2410_hcd_info *, int ports);
-};
-
-static void inline s3c2410_usb_report_oc(struct s3c2410_hcd_info *info, int ports)
-{
- if (info->report_oc != NULL) {
- (info->report_oc)(info, ports);
- }
-}
-
-extern void s3c_ohci_set_platdata(struct s3c2410_hcd_info *info);
-
-#endif /*__ASM_ARCH_USBCONTROL_H */
#include <linux/dmaengine.h>
#include <linux/ktime.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-ep93xx.h>
#include <mach/platform.h>
#define DRV_NAME "ep93xx-ide"
#include <scsi/scsi_host.h>
#include <mach/pxa2xx-regs.h>
-#include <mach/pata_pxa.h>
+#include <linux/platform_data/ata-pxa.h>
#include <mach/dma.h>
#define DRV_NAME "pata_pxa"
#include <linux/platform_device.h>
#include <linux/slab.h>
-#include <plat/ata.h>
+#include <linux/platform_data/ata-samsung_cf.h>
#include <plat/regs-ata.h>
#define DRV_NAME "pata_samsung_cf"
#include <plat/ste_dma40.h>
-#include <mach/crypto-ux500.h>
+#include <linux/platform_data/crypto-ux500.h>
#include <mach/hardware.h>
#include "cryp_p.h"
#include <crypto/scatterwalk.h>
#include <crypto/algapi.h>
-#include <mach/crypto-ux500.h>
+#include <linux/platform_data/crypto-ux500.h>
#include <mach/hardware.h>
#include "hash_alg.h"
#ifndef AT_HDMAC_REGS_H
#define AT_HDMAC_REGS_H
-#include <mach/at_hdmac.h>
+#include <linux/platform_data/dma-atmel.h>
#define AT_DMA_MAX_NR_CHANNELS 8
#include <linux/platform_device.h>
#include <linux/slab.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-ep93xx.h>
#include "dmaengine.h"
#include <linux/module.h>
#include <asm/irq.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-imx.h>
#include <mach/hardware.h>
#include "dmaengine.h"
#include <linux/of_device.h>
#include <asm/irq.h>
-#include <mach/sdma.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-imx-sdma.h>
+#include <linux/platform_data/dma-imx.h>
#include <mach/hardware.h>
#include "dmaengine.h"
#include <linux/platform_device.h>
#include <linux/device.h>
#include <mach/regs-icu.h>
-#include <mach/sram.h>
+#include <linux/platform_data/dma-mmp_tdma.h>
#include "dmaengine.h"
#include <linux/platform_device.h>
#include <linux/memory.h>
#include <linux/clk.h>
-#include <plat/mv_xor.h>
+#include <linux/platform_data/dma-mv_xor.h>
#include "dmaengine.h"
#include "mv_xor.h"
#include <linux/hwmon-sysfs.h>
#include <plat/adc.h>
-#include <plat/hwmon.h>
+#include <linux/platform_data/hwmon-s3c.h>
struct s3c_hwmon_attr {
struct sensor_device_attribute in;
#include <linux/gpio.h>
#include <mach/hardware.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-davinci.h>
/* ----- global defines ----------------------------------------------- */
#include <linux/pinctrl/consumer.h>
#include <mach/hardware.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-imx.h>
/** Defines ********************************************************************
*******************************************************************************/
#include <linux/io.h>
#include <mach/mfp.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-nuc900.h>
/* nuc900 i2c registers offset */
#include <asm/irq.h>
#include <plat/regs-iic.h>
-#include <plat/iic.h>
+#include <linux/platform_data/i2c-s3c2410.h>
/* Treat S3C2410 as baseline hardware, anything else is supported via quirks */
#define QUIRK_S3C2440 (1 << 0)
#include <mach/hardware.h>
#include <mach/irqs.h>
-#include <mach/keyscan.h>
+#include <linux/platform_data/keyscan-davinci.h>
/* Key scan registers */
#define DAVINCI_KEYSCAN_KEYCTRL 0x0000
#include <linux/slab.h>
#include <mach/hardware.h>
-#include <mach/ep93xx_keypad.h>
+#include <linux/platform_data/keypad-ep93xx.h>
/*
* Keypad Interface Register offsets
#include <linux/clk.h>
#include <linux/module.h>
-#include <plat/ske.h>
+#include <linux/platform_data/keypad-nomadik-ske.h>
/* SKE_CR bits */
#define SKE_KPMLT (0x1 << 6)
#include <asm/mach/map.h>
#include <mach/hardware.h>
-#include <plat/pxa27x_keypad.h>
+#include <linux/platform_data/keypad-pxa27x.h>
/*
* Keypad Controller registers
*/
#include <linux/io.h>
#include <linux/slab.h>
-#include <mach/pxa930_rotary.h>
+#include <linux/platform_data/keyboard-pxa930_rotary.h>
#define SBCR (0x04)
#define ERCR (0x0c)
#include <linux/io.h>
#include <linux/slab.h>
-#include <mach/w90p910_keypad.h>
+#include <linux/platform_data/keypad-w90p910.h>
/* Keypad Interface Control Registers */
#define KPI_CONF 0x00
#include <linux/slab.h>
#include <mach/hardware.h>
-#include <mach/pxa930_trkball.h>
+#include <linux/platform_data/mouse-pxa930_trkball.h>
/* Trackball Controller Register Definitions */
#define TBCR (0x000C)
#include <plat/adc.h>
#include <plat/regs-adc.h>
-#include <plat/ts.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
#define TSC_SLEEP (S3C2410_ADCTSC_PULL_UP_DISABLE | S3C2410_ADCTSC_XY_PST(0))
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/leds.h>
-#include <mach/leds-netxbig.h>
+#include <linux/platform_data/leds-kirkwood-netxbig.h>
/*
* GPIO extension bus.
#include <linux/gpio.h>
#include <linux/leds.h>
#include <linux/module.h>
-#include <mach/leds-ns2.h>
+#include <linux/platform_data/leds-kirkwood-ns2.h>
/*
* The Network Space v2 dual-GPIO LED is wired to a CPLD and can blink in
#include <mach/hardware.h>
#include <mach/regs-gpio.h>
-#include <mach/leds-gpio.h>
+#include <linux/platform_data/leds-s3c24xx.h>
/* our context */
#include <mach/hardware.h>
#include <mach/mux.h>
-#include <mach/i2c.h>
+#include <linux/platform_data/i2c-davinci.h>
#include <linux/io.h>
#include <linux/spinlock.h>
#include <linux/videodev2.h>
#include <media/v4l2-subdev.h>
-#include <plat/mipi_csis.h>
+#include <linux/platform_data/mipi-csis.h>
#include "mipi-csis.h"
static int debug;
#include <mach/dma-mx1-mx2.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
-#include <mach/mx1_camera.h>
+#include <linux/platform_data/camera-mx1.h>
/*
* CSI registers
#include <linux/videodev2.h>
-#include <mach/mx2_cam.h>
+#include <linux/platform_data/camera-mx2.h>
#include <mach/hardware.h>
#include <asm/dma.h>
#include <media/soc_mediabus.h>
#include <mach/ipu.h>
-#include <mach/mx3_camera.h>
-#include <mach/dma.h>
+#include <linux/platform_data/camera-mx3.h>
+#include <linux/platform_data/dma-imx.h>
#define MX3_CAM_DRV_NAME "mx3-camera"
#include <linux/videodev2.h>
#include <mach/dma.h>
-#include <mach/camera.h>
+#include <linux/platform_data/camera-pxa.h>
#define PXA_CAM_VERSION "0.0.6"
#define PXA_CAM_DRV_NAME "pxa27x-camera"
#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <mach/mcp.h>
+#include <linux/platform_data/mfd-mcp-sa11x0.h>
#define DRIVER_NAME "sa11x0-mcp"
#include <linux/dma-mapping.h>
#include <linux/mmc/mmc.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-davinci.h>
#include <mach/edma.h>
/*
#include <asm/div64.h>
#include <asm/sizes.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-msm_sdcc.h>
#include <mach/msm_iomap.h>
#include <mach/dma.h>
#include <mach/clk.h>
#include <asm/sizes.h>
#include <asm/unaligned.h>
-#include <plat/mvsdio.h>
+#include <linux/platform_data/mmc-mvsdio.h>
#include "mvsdio.h"
#include <asm/dma.h>
#include <asm/irq.h>
#include <asm/sizes.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-mxcmmc.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-imx.h>
#include <mach/hardware.h>
#define DRIVER_NAME "mxc-mmc"
#include <mach/hardware.h>
#include <mach/dma.h>
-#include <mach/mmc.h>
+#include <linux/platform_data/mmc-pxamci.h>
#include "pxamci.h"
#include <mach/regs-sdi.h>
-#include <plat/mci.h>
+#include <linux/platform_data/mmc-s3cmci.h>
#include "s3cmci.h"
#include <linux/of_device.h>
#include <linux/of_gpio.h>
#include <linux/pinctrl/consumer.h>
-#include <mach/esdhc.h>
+#include <linux/platform_data/mmc-esdhc-imx.h>
#include "sdhci-pltfm.h"
#include "sdhci-esdhc.h"
#include <asm/gpio.h>
#include <mach/gpio-tegra.h>
-#include <mach/sdhci.h>
+#include <linux/platform_data/mmc-sdhci-tegra.h>
#include "sdhci-pltfm.h"
#include <linux/mtd/partitions.h>
#include <linux/slab.h>
-#include <mach/nand.h>
-#include <mach/aemif.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/mtd-davinci-aemif.h>
/*
* This is a device driver for the NAND flash controller found on the
#include <linux/of_mtd.h>
#include <asm/mach/flash.h>
-#include <mach/mxc_nand.h>
+#include <linux/platform_data/mtd-mxc_nand.h>
#include <mach/hardware.h>
#define DRIVER_NAME "mxc_nand"
#include <linux/mtd/partitions.h>
#include <linux/io.h>
#include <linux/slab.h>
-#include <mach/nand.h>
+#include <linux/platform_data/mtd-nomadik-nand.h>
#include <mach/fsmc.h>
#include <mtd/mtd-abi.h>
#include <asm/io.h>
#include <asm/sizes.h>
#include <mach/hardware.h>
-#include <plat/orion_nand.h>
+#include <linux/platform_data/mtd-orion_nand.h>
static void orion_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
#include <linux/slab.h>
#include <mach/dma.h>
-#include <plat/pxa3xx_nand.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
#define CHIP_DELAY_TIMEOUT (2 * HZ/10)
#define NAND_STOP_DELAY (2 * HZ/50)
#include <asm/io.h>
#include <plat/regs-nand.h>
-#include <plat/nand.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
#ifdef CONFIG_MTD_NAND_S3C2410_HWECC
static int hardware_ecc = 1;
#include <mach/netx-regs.h>
#include <mach/pfifo.h>
#include <mach/xc.h>
-#include <mach/eth.h>
+#include <linux/platform_data/eth-netx.h>
/* XC Fifo Offsets */
#define EMPTY_PTR_FIFO(xcno) (0 + ((xcno) << 3)) /* Index of the empty pointer FIFO */
#include <net/irda/irda_device.h>
#include <mach/dma.h>
-#include <mach/irda.h>
+#include <linux/platform_data/irda-pxaficp.h>
#include <mach/regs-uart.h>
#include <mach/regs-ost.h>
#include <asm/irq.h>
-#include <mach/arcom-pcmcia.h>
+#include <linux/platform_data/pcmcia-pxa2xx_viper.h>
#include "soc_common.h"
#include "pxa2xx_base.h"
#include <linux/spi/spi_bitbang.h>
#include <linux/slab.h>
-#include <mach/spi.h>
+#include <linux/platform_data/spi-davinci.h>
#include <mach/edma.h>
#define SPI_NO_RESOURCE ((resource_size_t)-1)
#include <linux/scatterlist.h>
#include <linux/spi/spi.h>
-#include <mach/dma.h>
-#include <mach/ep93xx_spi.h>
+#include <linux/platform_data/dma-ep93xx.h>
+#include <linux/platform_data/spi-ep93xx.h>
#define SSPCR0 0x0000
#define SSPCR0_MODE_SHIFT 6
#include <linux/of_gpio.h>
#include <linux/pinctrl/consumer.h>
-#include <mach/spi.h>
+#include <linux/platform_data/spi-imx.h>
#define DRIVER_NAME "spi_imx"
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
-#include <mach/nuc900_spi.h>
+#include <linux/platform_data/spi-nuc900.h>
/* usi registers offset */
#define USI_CNT 0x00
#include <linux/of_gpio.h>
#include <mach/dma.h>
-#include <plat/s3c64xx-spi.h>
+#include <linux/platform_data/spi-s3c64xx.h>
#define MAX_SPI_PORTS 3
#include <asm/io.h>
#include <asm/irq.h>
-#include <mach/imx-uart.h>
+#include <linux/platform_data/serial-imx.h>
/* Register definitions */
#define URXD0 0x0 /* Receiver Register */
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
-#include <mach/usb.h>
+#include <linux/platform_data/usb-imx_udc.h>
#include <mach/hardware.h>
#include "imx_udc.h"
#include <mach/hardware.h>
#include <plat/regs-udc.h>
-#include <plat/udc.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
#include "s3c2410_udc.h"
#include <linux/slab.h>
#include <mach/hardware.h>
-#include <mach/mxc_ehci.h>
+#include <linux/platform_data/usb-ehci-mxc.h>
#include <asm/mach-types.h>
#include <linux/platform_device.h>
#include <linux/mbus.h>
#include <linux/clk.h>
-#include <plat/ehci-orion.h>
+#include <linux/platform_data/usb-ehci-orion.h>
#define rdl(off) __raw_readl(hcd->regs + (off))
#define wrl(off, val) __raw_writel((val), hcd->regs + (off))
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/of_gpio.h>
-#include <plat/ehci.h>
+#include <linux/platform_data/usb-ehci-s5p.h>
#include <plat/usb-phy.h>
#define EHCI_INSNREG00(base) (base + 0x90)
#ifndef __LINUX_IMX21_HCD_H__
#define __LINUX_IMX21_HCD_H__
-#include <mach/mx21-usbhost.h>
+#include <linux/platform_data/usb-mx2.h>
#define NUM_ISO_ETDS 2
#define USB_NUM_ETD 32
#include <linux/clk.h>
#include <mach/da8xx.h>
-#include <mach/usb.h>
+#include <linux/platform_data/usb-davinci.h>
#ifndef CONFIG_ARCH_DAVINCI_DA8XX
#error "This file is DA8xx bus glue. Define CONFIG_ARCH_DAVINCI_DA8XX."
#include <linux/clk.h>
#include <linux/of.h>
#include <linux/platform_device.h>
-#include <mach/ohci.h>
+#include <linux/platform_data/usb-exynos.h>
#include <plat/usb-phy.h>
struct exynos_ohci_hcd {
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <mach/hardware.h>
-#include <mach/ohci.h>
-#include <mach/pxa3xx-u2d.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/usb-pxa3xx-ulpi.h>
/*
* UHC: USB Host Controller (OHCI-like) register definitions
#include <linux/platform_device.h>
#include <linux/clk.h>
-#include <plat/usb-control.h>
+#include <linux/platform_data/usb-ohci-s3c2410.h>
#define valid_port(idx) ((idx) == 1 || (idx) == 2)
#include <linux/dma-mapping.h>
#include <mach/da8xx.h>
-#include <mach/usb.h>
+#include <linux/platform_data/usb-davinci.h>
#include "musb_core.h"
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
#include <linux/pfn.h>
-#include <mach/usb.h>
+#include <linux/platform_data/usb-musb-ux500.h>
#include "musb_core.h"
struct ux500_dma_channel {
#include <linux/clk.h>
#include <linux/fb.h>
-#include <mach/fb.h>
+#include <linux/platform_data/video-ep93xx.h>
/* Vertical Frame Timing Registers */
#define EP93XXFB_VLINES_TOTAL 0x0000 /* SW locked */
#include <linux/io.h>
#include <linux/math64.h>
-#include <mach/imxfb.h>
+#include <linux/platform_data/video-imxfb.h>
#include <mach/hardware.h>
/*
#include <mach/msm_iomap.h>
#include <mach/irqs.h>
#include <mach/board.h>
-#include <mach/msm_fb.h>
+#include <linux/platform_data/video-msm_fb.h>
#include "mddi_hw.h"
#define FLAG_DISABLE_HIBERNATION 0x0001
#include <linux/kernel.h>
#include <linux/platform_device.h>
-#include <mach/msm_fb.h>
+#include <linux/platform_data/video-msm_fb.h>
struct panel_info {
struct platform_device pdev;
#include <linux/sched.h>
#include <linux/gpio.h>
#include <linux/slab.h>
-#include <mach/msm_fb.h>
+#include <linux/platform_data/video-msm_fb.h>
static DECLARE_WAIT_QUEUE_HEAD(nt35399_vsync_wait);
#include <linux/gpio.h>
#include <linux/sched.h>
#include <linux/slab.h>
-#include <mach/msm_fb.h>
+#include <linux/platform_data/video-msm_fb.h>
#define LCD_CONTROL_BLOCK_BASE 0x110000
#include <linux/slab.h>
#include <mach/msm_iomap.h>
-#include <mach/msm_fb.h>
+#include <linux/platform_data/video-msm_fb.h>
#include <linux/platform_device.h>
#include <linux/export.h>
#define _MDP_HW_H_
#include <mach/msm_iomap.h>
-#include <mach/msm_fb.h>
+#include <linux/platform_data/video-msm_fb.h>
struct mdp_info {
struct mdp_device mdp_dev;
#include <linux/file.h>
#include <linux/delay.h>
#include <linux/msm_mdp.h>
-#include <mach/msm_fb.h>
+#include <linux/platform_data/video-msm_fb.h>
#include "mdp_hw.h"
#include "mdp_scale_tables.h"
#include <linux/msm_mdp.h>
#include <linux/io.h>
#include <linux/uaccess.h>
-#include <mach/msm_fb.h>
+#include <linux/platform_data/video-msm_fb.h>
#include <mach/board.h>
#include <linux/workqueue.h>
#include <linux/clk.h>
#include <linux/clk.h>
#include <linux/mutex.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-imx.h>
#include <mach/hardware.h>
#include <mach/ipu.h>
-#include <mach/mx3fb.h>
+#include <linux/platform_data/video-mx3fb.h>
#include <asm/io.h>
#include <asm/uaccess.h>
#include <mach/map.h>
#include <mach/regs-clock.h>
#include <mach/regs-ldm.h>
-#include <mach/fb.h>
+#include <linux/platform_data/video-nuc900fb.h>
#include "nuc900fb.h"
#define __NUC900FB_H
#include <mach/map.h>
-#include <mach/fb.h>
+#include <linux/platform_data/video-nuc900fb.h>
enum nuc900_lcddrv_type {
LCDDRV_NUC910,
#include <asm/irq.h>
#include <asm/div64.h>
#include <mach/bitfield.h>
-#include <mach/pxafb.h>
+#include <linux/platform_data/video-pxafb.h>
/*
* Complain if VAR is out of range.
#include <linux/platform_device.h>
#include <linux/wait.h>
-#include <mach/vt8500fb.h>
+#include <linux/platform_data/video-vt8500lcdfb.h>
#include "vt8500lcdfb.h"
#include "wmt_ge_rops.h"
#include <linux/platform_device.h>
#include <linux/wait.h>
-#include <mach/vt8500fb.h>
+#include <linux/platform_data/video-vt8500lcdfb.h>
#include "wm8505fb_regs.h"
#include "wmt_ge_rops.h"
--- /dev/null
+#ifndef __MACH_SSI_H
+#define __MACH_SSI_H
+
+struct snd_ac97;
+
+extern unsigned char imx_ssi_fiq_start, imx_ssi_fiq_end;
+extern unsigned long imx_ssi_fiq_base, imx_ssi_fiq_tx_buffer, imx_ssi_fiq_rx_buffer;
+
+struct imx_ssi_platform_data {
+ unsigned int flags;
+#define IMX_SSI_DMA (1 << 0)
+#define IMX_SSI_USE_AC97 (1 << 1)
+#define IMX_SSI_NET (1 << 2)
+#define IMX_SSI_SYN (1 << 3)
+#define IMX_SSI_USE_I2S_SLAVE (1 << 4)
+ void (*ac97_reset) (struct snd_ac97 *ac97);
+ void (*ac97_warm_reset)(struct snd_ac97 *ac97);
+};
+
+#endif /* __MACH_SSI_H */
+
--- /dev/null
+#ifndef __PLAT_AUDIO_H
+#define __PLAT_AUDIO_H
+
+struct kirkwood_asoc_platform_data {
+ int burst;
+};
+#endif
--- /dev/null
+#ifndef _INCLUDE_PALMASOC_H_
+#define _INCLUDE_PALMASOC_H_
+
+struct palm27x_asoc_info {
+ int jack_gpio;
+};
+
+#endif
--- /dev/null
+/* arch/arm/plat-samsung/include/plat/audio.h
+ *
+ * Copyright (c) 2009 Samsung Electronics Co. Ltd
+ * Author: Jaswinder Singh <jassi.brar@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* The machine init code calls s3c*_ac97_setup_gpio with
+ * one of these defines in order to select appropriate bank
+ * of GPIO for AC97 pins
+ */
+#define S3C64XX_AC97_GPD 0
+#define S3C64XX_AC97_GPE 1
+extern void s3c64xx_ac97_setup_gpio(int);
+
+/*
+ * The machine init code calls s5p*_spdif_setup_gpio with
+ * one of these defines in order to select appropriate bank
+ * of GPIO for S/PDIF pins
+ */
+#define S5PC100_SPDIF_GPD 0
+#define S5PC100_SPDIF_GPG3 1
+extern void s5pc100_spdif_setup_gpio(int);
+
+struct samsung_i2s {
+/* If the Primary DAI has 5.1 Channels */
+#define QUIRK_PRI_6CHAN (1 << 0)
+/* If the I2S block has a Stereo Overlay Channel */
+#define QUIRK_SEC_DAI (1 << 1)
+/*
+ * If the I2S block has no internal prescalar or MUX (I2SMOD[10] bit)
+ * The Machine driver must provide suitably set clock to the I2S block.
+ */
+#define QUIRK_NO_MUXPSR (1 << 2)
+#define QUIRK_NEED_RSTCLR (1 << 3)
+ /* Quirks of the I2S controller */
+ u32 quirks;
+
+ /*
+ * Array of clock names that can be used to generate I2S signals.
+ * Also corresponds to clocks of I2SMOD[10]
+ */
+ const char **src_clk;
+ dma_addr_t idma_addr;
+};
+
+/**
+ * struct s3c_audio_pdata - common platform data for audio device drivers
+ * @cfg_gpio: Callback function to setup mux'ed pins in I2S/PCM/AC97 mode
+ */
+struct s3c_audio_pdata {
+ int (*cfg_gpio)(struct platform_device *);
+ union {
+ struct samsung_i2s i2s;
+ } type;
+};
--- /dev/null
+/* arch/arm/plat-samsung/include/plat/audio-simtec.h
+ *
+ * Copyright 2008 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Simtec Audio support.
+*/
+
+/**
+ * struct s3c24xx_audio_simtec_pdata - platform data for simtec audio
+ * @use_mpllin: Select codec clock from MPLLin
+ * @output_cdclk: Need to output CDCLK to the codec
+ * @have_mic: Set if we have a MIC socket
+ * @have_lout: Set if we have a LineOut socket
+ * @amp_gpio: GPIO pin to enable the AMP
+ * @amp_gain: Option GPIO to control AMP gain
+ */
+struct s3c24xx_audio_simtec_pdata {
+ unsigned int use_mpllin:1;
+ unsigned int output_cdclk:1;
+
+ unsigned int have_mic:1;
+ unsigned int have_lout:1;
+
+ int amp_gpio;
+ int amp_gain[2];
+
+ void (*startup)(void);
+};
--- /dev/null
+/*
+ * Generic PXA PATA driver
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING. If not, write to
+ * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __MACH_PATA_PXA_H__
+#define __MACH_PATA_PXA_H__
+
+struct pata_pxa_pdata {
+ /* PXA DMA DREQ<0:2> pin */
+ uint32_t dma_dreq;
+ /* Register shift */
+ uint32_t reg_shift;
+ /* IRQ flags */
+ uint32_t irq_flags;
+};
+
+#endif /* __MACH_PATA_PXA_H__ */
--- /dev/null
+/* linux/arch/arm/plat-samsung/include/plat/ata.h
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * Samsung CF-ATA platform_device info
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_ATA_H
+#define __ASM_PLAT_ATA_H __FILE__
+
+/**
+ * struct s3c_ide_platdata - S3C IDE driver platform data.
+ * @setup_gpio: Setup the external GPIO pins to the right state for data
+ * transfer in true-ide mode.
+ */
+struct s3c_ide_platdata {
+ void (*setup_gpio)(void);
+};
+
+/*
+ * s3c_ide_set_platdata() - Setup the platform specifc data for IDE driver.
+ * @pdata: Platform data for IDE driver.
+ */
+extern void s3c_ide_set_platdata(struct s3c_ide_platdata *pdata);
+
+/* architecture-specific IDE configuration */
+extern void s3c64xx_ide_setup_gpio(void);
+extern void s5pc100_ide_setup_gpio(void);
+extern void s5pv210_ide_setup_gpio(void);
+
+#endif /*__ASM_PLAT_ATA_H */
#ifndef __LINUX_ATMEL_AES_H
#define __LINUX_ATMEL_AES_H
-#include <mach/at_hdmac.h>
+#include <linux/platform_data/dma-atmel.h>
/**
* struct aes_dma_data - DMA data for AES
--- /dev/null
+/*
+ * mx1_camera.h - i.MX1/i.MXL camera driver header file
+ *
+ * Copyright (c) 2008, Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
+ * Copyright (C) 2009, Darius Augulis <augulis.darius@gmail.com>
+ *
+ * Based on PXA camera.h file:
+ * Copyright (C) 2003, Intel Corporation
+ * Copyright (C) 2008, Guennadi Liakhovetski <kernel@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_CAMERA_H_
+#define __ASM_ARCH_CAMERA_H_
+
+#define MX1_CAMERA_DATA_HIGH 1
+#define MX1_CAMERA_PCLK_RISING 2
+#define MX1_CAMERA_VSYNC_HIGH 4
+
+extern unsigned char mx1_camera_sof_fiq_start, mx1_camera_sof_fiq_end;
+
+/**
+ * struct mx1_camera_pdata - i.MX1/i.MXL camera platform data
+ * @mclk_10khz: master clock frequency in 10kHz units
+ * @flags: MX1 camera platform flags
+ */
+struct mx1_camera_pdata {
+ unsigned long mclk_10khz;
+ unsigned long flags;
+};
+
+#endif /* __ASM_ARCH_CAMERA_H_ */
--- /dev/null
+/*
+ * mx2-cam.h - i.MX27/i.MX25 camera driver header file
+ *
+ * Copyright (C) 2003, Intel Corporation
+ * Copyright (C) 2008, Sascha Hauer <s.hauer@pengutronix.de>
+ * Copyright (C) 2010, Baruch Siach <baruch@tkos.co.il>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#ifndef __MACH_MX2_CAM_H_
+#define __MACH_MX2_CAM_H_
+
+#define MX2_CAMERA_SWAP16 (1 << 0)
+#define MX2_CAMERA_EXT_VSYNC (1 << 1)
+#define MX2_CAMERA_CCIR (1 << 2)
+#define MX2_CAMERA_CCIR_INTERLACE (1 << 3)
+#define MX2_CAMERA_HSYNC_HIGH (1 << 4)
+#define MX2_CAMERA_GATED_CLOCK (1 << 5)
+#define MX2_CAMERA_INV_DATA (1 << 6)
+#define MX2_CAMERA_PCLK_SAMPLE_RISING (1 << 7)
+#define MX2_CAMERA_PACK_DIR_MSB (1 << 8)
+
+/**
+ * struct mx2_camera_platform_data - optional platform data for mx2_camera
+ * @flags: any combination of MX2_CAMERA_*
+ * @clk: clock rate of the csi block / 2
+ */
+struct mx2_camera_platform_data {
+ unsigned long flags;
+ unsigned long clk;
+};
+
+#endif /* __MACH_MX2_CAM_H_ */
--- /dev/null
+/*
+ * mx3_camera.h - i.MX3x camera driver header file
+ *
+ * Copyright (C) 2008, Guennadi Liakhovetski, DENX Software Engineering, <lg@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _MX3_CAMERA_H_
+#define _MX3_CAMERA_H_
+
+#include <linux/device.h>
+
+#define MX3_CAMERA_CLK_SRC 1
+#define MX3_CAMERA_EXT_VSYNC 2
+#define MX3_CAMERA_DP 4
+#define MX3_CAMERA_PCP 8
+#define MX3_CAMERA_HSP 0x10
+#define MX3_CAMERA_VSP 0x20
+#define MX3_CAMERA_DATAWIDTH_4 0x40
+#define MX3_CAMERA_DATAWIDTH_8 0x80
+#define MX3_CAMERA_DATAWIDTH_10 0x100
+#define MX3_CAMERA_DATAWIDTH_15 0x200
+
+#define MX3_CAMERA_DATAWIDTH_MASK (MX3_CAMERA_DATAWIDTH_4 | MX3_CAMERA_DATAWIDTH_8 | \
+ MX3_CAMERA_DATAWIDTH_10 | MX3_CAMERA_DATAWIDTH_15)
+
+/**
+ * struct mx3_camera_pdata - i.MX3x camera platform data
+ * @flags: MX3_CAMERA_* flags
+ * @mclk_10khz: master clock frequency in 10kHz units
+ * @dma_dev: IPU DMA device to match against in channel allocation
+ */
+struct mx3_camera_pdata {
+ unsigned long flags;
+ unsigned long mclk_10khz;
+ struct device *dma_dev;
+};
+
+#endif
--- /dev/null
+/*
+ camera.h - PXA camera driver header file
+
+ Copyright (C) 2003, Intel Corporation
+ Copyright (C) 2008, Guennadi Liakhovetski <kernel@pengutronix.de>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+#ifndef __ASM_ARCH_CAMERA_H_
+#define __ASM_ARCH_CAMERA_H_
+
+#define PXA_CAMERA_MASTER 1
+#define PXA_CAMERA_DATAWIDTH_4 2
+#define PXA_CAMERA_DATAWIDTH_5 4
+#define PXA_CAMERA_DATAWIDTH_8 8
+#define PXA_CAMERA_DATAWIDTH_9 0x10
+#define PXA_CAMERA_DATAWIDTH_10 0x20
+#define PXA_CAMERA_PCLK_EN 0x40
+#define PXA_CAMERA_MCLK_EN 0x80
+#define PXA_CAMERA_PCP 0x100
+#define PXA_CAMERA_HSP 0x200
+#define PXA_CAMERA_VSP 0x400
+
+struct pxacamera_platform_data {
+ unsigned long flags;
+ unsigned long mclk_10khz;
+};
+
+extern void pxa_set_camera_info(struct pxacamera_platform_data *);
+
+#endif /* __ASM_ARCH_CAMERA_H_ */
--- /dev/null
+/*
+ * Copyright (C) ST-Ericsson SA 2011
+ *
+ * Author: Joakim Bech <joakim.xx.bech@stericsson.com> for ST-Ericsson
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#ifndef _CRYPTO_UX500_H
+#define _CRYPTO_UX500_H
+#include <linux/dmaengine.h>
+#include <plat/ste_dma40.h>
+
+struct hash_platform_data {
+ void *mem_to_engine;
+ bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
+};
+
+struct cryp_platform_data {
+ struct stedma40_chan_cfg mem_to_engine;
+ struct stedma40_chan_cfg engine_to_mem;
+};
+
+#endif
--- /dev/null
+/*
+ * Header file for the Atmel AHB DMA Controller driver
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef AT_HDMAC_H
+#define AT_HDMAC_H
+
+#include <linux/dmaengine.h>
+
+/**
+ * struct at_dma_platform_data - Controller configuration parameters
+ * @nr_channels: Number of channels supported by hardware (max 8)
+ * @cap_mask: dma_capability flags supported by the platform
+ */
+struct at_dma_platform_data {
+ unsigned int nr_channels;
+ dma_cap_mask_t cap_mask;
+};
+
+/**
+ * struct at_dma_slave - Controller-specific information about a slave
+ * @dma_dev: required DMA master device
+ * @cfg: Platform-specific initializer for the CFG register
+ */
+struct at_dma_slave {
+ struct device *dma_dev;
+ u32 cfg;
+};
+
+
+/* Platform-configurable bits in CFG */
+#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */
+#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */
+#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */
+#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */
+#define ATC_SRC_H2SEL_SW (0x0 << 9)
+#define ATC_SRC_H2SEL_HW (0x1 << 9)
+#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */
+#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */
+#define ATC_DST_H2SEL_SW (0x0 << 13)
+#define ATC_DST_H2SEL_HW (0x1 << 13)
+#define ATC_SOD (0x1 << 16) /* Stop On Done */
+#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */
+#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */
+#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */
+#define ATC_LOCK_IF_L_CHUNK (0x0 << 22)
+#define ATC_LOCK_IF_L_BUFFER (0x1 << 22)
+#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */
+#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */
+#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28)
+#define ATC_FIFOCFG_HALFFIFO (0x1 << 28)
+#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28)
+
+
+#endif /* AT_HDMAC_H */
--- /dev/null
+#ifndef __ASM_ARCH_DMA_H
+#define __ASM_ARCH_DMA_H
+
+#include <linux/types.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+
+/*
+ * M2P channels.
+ *
+ * Note that these values are also directly used for setting the PPALLOC
+ * register.
+ */
+#define EP93XX_DMA_I2S1 0
+#define EP93XX_DMA_I2S2 1
+#define EP93XX_DMA_AAC1 2
+#define EP93XX_DMA_AAC2 3
+#define EP93XX_DMA_AAC3 4
+#define EP93XX_DMA_I2S3 5
+#define EP93XX_DMA_UART1 6
+#define EP93XX_DMA_UART2 7
+#define EP93XX_DMA_UART3 8
+#define EP93XX_DMA_IRDA 9
+/* M2M channels */
+#define EP93XX_DMA_SSP 10
+#define EP93XX_DMA_IDE 11
+
+/**
+ * struct ep93xx_dma_data - configuration data for the EP93xx dmaengine
+ * @port: peripheral which is requesting the channel
+ * @direction: TX/RX channel
+ * @name: optional name for the channel, this is displayed in /proc/interrupts
+ *
+ * This information is passed as private channel parameter in a filter
+ * function. Note that this is only needed for slave/cyclic channels. For
+ * memcpy channels %NULL data should be passed.
+ */
+struct ep93xx_dma_data {
+ int port;
+ enum dma_transfer_direction direction;
+ const char *name;
+};
+
+/**
+ * struct ep93xx_dma_chan_data - platform specific data for a DMA channel
+ * @name: name of the channel, used for getting the right clock for the channel
+ * @base: mapped registers
+ * @irq: interrupt number used by this channel
+ */
+struct ep93xx_dma_chan_data {
+ const char *name;
+ void __iomem *base;
+ int irq;
+};
+
+/**
+ * struct ep93xx_dma_platform_data - platform data for the dmaengine driver
+ * @channels: array of channels which are passed to the driver
+ * @num_channels: number of channels in the array
+ *
+ * This structure is passed to the DMA engine driver via platform data. For
+ * M2P channels, contract is that even channels are for TX and odd for RX.
+ * There is no requirement for the M2M channels.
+ */
+struct ep93xx_dma_platform_data {
+ struct ep93xx_dma_chan_data *channels;
+ size_t num_channels;
+};
+
+static inline bool ep93xx_dma_chan_is_m2p(struct dma_chan *chan)
+{
+ return !strcmp(dev_name(chan->device->dev), "ep93xx-dma-m2p");
+}
+
+/**
+ * ep93xx_dma_chan_direction - returns direction the channel can be used
+ * @chan: channel
+ *
+ * This function can be used in filter functions to find out whether the
+ * channel supports given DMA direction. Only M2P channels have such
+ * limitation, for M2M channels the direction is configurable.
+ */
+static inline enum dma_transfer_direction
+ep93xx_dma_chan_direction(struct dma_chan *chan)
+{
+ if (!ep93xx_dma_chan_is_m2p(chan))
+ return DMA_NONE;
+
+ /* even channels are for TX, odd for RX */
+ return (chan->chan_id % 2 == 0) ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM;
+}
+
+#endif /* __ASM_ARCH_DMA_H */
--- /dev/null
+#ifndef __MACH_MXC_SDMA_H__
+#define __MACH_MXC_SDMA_H__
+
+/**
+ * struct sdma_script_start_addrs - SDMA script start pointers
+ *
+ * start addresses of the different functions in the physical
+ * address space of the SDMA engine.
+ */
+struct sdma_script_start_addrs {
+ s32 ap_2_ap_addr;
+ s32 ap_2_bp_addr;
+ s32 ap_2_ap_fixed_addr;
+ s32 bp_2_ap_addr;
+ s32 loopback_on_dsp_side_addr;
+ s32 mcu_interrupt_only_addr;
+ s32 firi_2_per_addr;
+ s32 firi_2_mcu_addr;
+ s32 per_2_firi_addr;
+ s32 mcu_2_firi_addr;
+ s32 uart_2_per_addr;
+ s32 uart_2_mcu_addr;
+ s32 per_2_app_addr;
+ s32 mcu_2_app_addr;
+ s32 per_2_per_addr;
+ s32 uartsh_2_per_addr;
+ s32 uartsh_2_mcu_addr;
+ s32 per_2_shp_addr;
+ s32 mcu_2_shp_addr;
+ s32 ata_2_mcu_addr;
+ s32 mcu_2_ata_addr;
+ s32 app_2_per_addr;
+ s32 app_2_mcu_addr;
+ s32 shp_2_per_addr;
+ s32 shp_2_mcu_addr;
+ s32 mshc_2_mcu_addr;
+ s32 mcu_2_mshc_addr;
+ s32 spdif_2_mcu_addr;
+ s32 mcu_2_spdif_addr;
+ s32 asrc_2_mcu_addr;
+ s32 ext_mem_2_ipu_addr;
+ s32 descrambler_addr;
+ s32 dptc_dvfs_addr;
+ s32 utra_addr;
+ s32 ram_code_start_addr;
+};
+
+/**
+ * struct sdma_platform_data - platform specific data for SDMA engine
+ *
+ * @fw_name The firmware name
+ * @script_addrs SDMA scripts addresses in SDMA ROM
+ */
+struct sdma_platform_data {
+ char *fw_name;
+ struct sdma_script_start_addrs *script_addrs;
+};
+
+#endif /* __MACH_MXC_SDMA_H__ */
--- /dev/null
+/*
+ * Copyright 2004-2009 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_MXC_DMA_H__
+#define __ASM_ARCH_MXC_DMA_H__
+
+#include <linux/scatterlist.h>
+#include <linux/device.h>
+#include <linux/dmaengine.h>
+
+/*
+ * This enumerates peripheral types. Used for SDMA.
+ */
+enum sdma_peripheral_type {
+ IMX_DMATYPE_SSI, /* MCU domain SSI */
+ IMX_DMATYPE_SSI_SP, /* Shared SSI */
+ IMX_DMATYPE_MMC, /* MMC */
+ IMX_DMATYPE_SDHC, /* SDHC */
+ IMX_DMATYPE_UART, /* MCU domain UART */
+ IMX_DMATYPE_UART_SP, /* Shared UART */
+ IMX_DMATYPE_FIRI, /* FIRI */
+ IMX_DMATYPE_CSPI, /* MCU domain CSPI */
+ IMX_DMATYPE_CSPI_SP, /* Shared CSPI */
+ IMX_DMATYPE_SIM, /* SIM */
+ IMX_DMATYPE_ATA, /* ATA */
+ IMX_DMATYPE_CCM, /* CCM */
+ IMX_DMATYPE_EXT, /* External peripheral */
+ IMX_DMATYPE_MSHC, /* Memory Stick Host Controller */
+ IMX_DMATYPE_MSHC_SP, /* Shared Memory Stick Host Controller */
+ IMX_DMATYPE_DSP, /* DSP */
+ IMX_DMATYPE_MEMORY, /* Memory */
+ IMX_DMATYPE_FIFO_MEMORY,/* FIFO type Memory */
+ IMX_DMATYPE_SPDIF, /* SPDIF */
+ IMX_DMATYPE_IPU_MEMORY, /* IPU Memory */
+ IMX_DMATYPE_ASRC, /* ASRC */
+ IMX_DMATYPE_ESAI, /* ESAI */
+};
+
+enum imx_dma_prio {
+ DMA_PRIO_HIGH = 0,
+ DMA_PRIO_MEDIUM = 1,
+ DMA_PRIO_LOW = 2
+};
+
+struct imx_dma_data {
+ int dma_request; /* DMA request line */
+ enum sdma_peripheral_type peripheral_type;
+ int priority;
+};
+
+static inline int imx_dma_is_ipu(struct dma_chan *chan)
+{
+ return !strcmp(dev_name(chan->device->dev), "ipu-core");
+}
+
+static inline int imx_dma_is_general_purpose(struct dma_chan *chan)
+{
+ return strstr(dev_name(chan->device->dev), "sdma") ||
+ !strcmp(dev_name(chan->device->dev), "imx-dma");
+}
+
+#endif
--- /dev/null
+/*
+ * linux/arch/arm/mach-mmp/include/mach/sram.h
+ *
+ * SRAM Memory Management
+ *
+ * Copyright (c) 2011 Marvell Semiconductors Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __ASM_ARCH_SRAM_H
+#define __ASM_ARCH_SRAM_H
+
+#include <linux/genalloc.h>
+
+/* ARBITRARY: SRAM allocations are multiples of this 2^N size */
+#define SRAM_GRANULARITY 512
+
+enum sram_type {
+ MMP_SRAM_UNDEFINED = 0,
+ MMP_ASRAM,
+ MMP_ISRAM,
+};
+
+struct sram_platdata {
+ char *pool_name;
+ int granularity;
+};
+
+extern struct gen_pool *sram_get_gpool(char *pool_name);
+
+#endif /* __ASM_ARCH_SRAM_H */
--- /dev/null
+/*
+ * arch/arm/plat-orion/include/plat/mv_xor.h
+ *
+ * Marvell XOR platform device data definition file.
+ */
+
+#ifndef __PLAT_MV_XOR_H
+#define __PLAT_MV_XOR_H
+
+#include <linux/dmaengine.h>
+#include <linux/mbus.h>
+
+#define MV_XOR_SHARED_NAME "mv_xor_shared"
+#define MV_XOR_NAME "mv_xor"
+
+struct mv_xor_platform_data {
+ struct platform_device *shared;
+ int hw_id;
+ dma_cap_mask_t cap_mask;
+ size_t pool_size;
+};
+
+
+#endif
--- /dev/null
+/*
+ * arch/arm/mach-netx/include/mach/eth.h
+ *
+ * Copyright (c) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef ASMARM_ARCH_ETH_H
+#define ASMARM_ARCH_ETH_H
+
+struct netxeth_platform_data {
+ unsigned int xcno; /* number of xmac/xpec engine this eth uses */
+};
+
+#endif
--- /dev/null
+/* linux/arch/arm/plat-s3c/include/plat/hwmon.h
+ *
+ * Copyright 2005 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C - HWMon interface for ADC
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_ADC_HWMON_H
+#define __ASM_ARCH_ADC_HWMON_H __FILE__
+
+/**
+ * s3c_hwmon_chcfg - channel configuration
+ * @name: The name to give this channel.
+ * @mult: Multiply the ADC value read by this.
+ * @div: Divide the value from the ADC by this.
+ *
+ * The value read from the ADC is converted to a value that
+ * hwmon expects (mV) by result = (value_read * @mult) / @div.
+ */
+struct s3c_hwmon_chcfg {
+ const char *name;
+ unsigned int mult;
+ unsigned int div;
+};
+
+/**
+ * s3c_hwmon_pdata - HWMON platform data
+ * @in: One configuration for each possible channel used.
+ */
+struct s3c_hwmon_pdata {
+ struct s3c_hwmon_chcfg *in[8];
+};
+
+/**
+ * s3c_hwmon_set_platdata - Set platform data for S3C HWMON device
+ * @pd: Platform data to register to device.
+ *
+ * Register the given platform data for use with the S3C HWMON device.
+ * The call will copy the platform data, so the board definitions can
+ * make the structure itself __initdata.
+ */
+extern void __init s3c_hwmon_set_platdata(struct s3c_hwmon_pdata *pd);
+
+#endif /* __ASM_ARCH_ADC_HWMON_H */
+
--- /dev/null
+/*
+ * DaVinci I2C controller platform_device info
+ *
+ * Author: Vladimir Barinov, MontaVista Software, Inc. <source@mvista.com>
+ *
+ * 2007 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+*/
+
+#ifndef __ASM_ARCH_I2C_H
+#define __ASM_ARCH_I2C_H
+
+/* All frequencies are expressed in kHz */
+struct davinci_i2c_platform_data {
+ unsigned int bus_freq; /* standard bus frequency (kHz) */
+ unsigned int bus_delay; /* post-transaction delay (usec) */
+ unsigned int sda_pin; /* GPIO pin ID to use for SDA */
+ unsigned int scl_pin; /* GPIO pin ID to use for SCL */
+};
+
+/* for board setup code */
+void davinci_init_i2c(struct davinci_i2c_platform_data *);
+
+#endif /* __ASM_ARCH_I2C_H */
--- /dev/null
+/*
+ * i2c.h - i.MX I2C driver header file
+ *
+ * Copyright (c) 2008, Darius Augulis <augulis.darius@gmail.com>
+ *
+ * This file is released under the GPLv2
+ */
+
+#ifndef __ASM_ARCH_I2C_H_
+#define __ASM_ARCH_I2C_H_
+
+/**
+ * struct imxi2c_platform_data - structure of platform data for MXC I2C driver
+ * @bitrate: Bus speed measured in Hz
+ *
+ **/
+struct imxi2c_platform_data {
+ u32 bitrate;
+};
+
+#endif /* __ASM_ARCH_I2C_H_ */
--- /dev/null
+#ifndef __ASM_ARCH_NUC900_I2C_H
+#define __ASM_ARCH_NUC900_I2C_H
+
+struct nuc900_platform_i2c {
+ int bus_num;
+ unsigned long bus_freq;
+};
+
+#endif /* __ASM_ARCH_NUC900_I2C_H */
--- /dev/null
+/* arch/arm/plat-s3c/include/plat/iic.h
+ *
+ * Copyright 2004-2009 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C - I2C Controller platform_device info
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_IIC_H
+#define __ASM_ARCH_IIC_H __FILE__
+
+#define S3C_IICFLG_FILTER (1<<0) /* enable s3c2440 filter */
+
+/**
+ * struct s3c2410_platform_i2c - Platform data for s3c I2C.
+ * @bus_num: The bus number to use (if possible).
+ * @flags: Any flags for the I2C bus (E.g. S3C_IICFLK_FILTER).
+ * @slave_addr: The I2C address for the slave device (if enabled).
+ * @frequency: The desired frequency in Hz of the bus. This is
+ * guaranteed to not be exceeded. If the caller does
+ * not care, use zero and the driver will select a
+ * useful default.
+ * @sda_delay: The delay (in ns) applied to SDA edges.
+ * @cfg_gpio: A callback to configure the pins for I2C operation.
+ */
+struct s3c2410_platform_i2c {
+ int bus_num;
+ unsigned int flags;
+ unsigned int slave_addr;
+ unsigned long frequency;
+ unsigned int sda_delay;
+
+ void (*cfg_gpio)(struct platform_device *dev);
+};
+
+/**
+ * s3c_i2c0_set_platdata - set platform data for i2c0 device
+ * @i2c: The platform data to set, or NULL for default data.
+ *
+ * Register the given platform data for use with the i2c0 device. This
+ * call copies the platform data, so the caller can use __initdata for
+ * their copy.
+ *
+ * This call will set cfg_gpio if is null to the default platform
+ * implementation.
+ *
+ * Any user of s3c_device_i2c0 should call this, even if it is with
+ * NULL to ensure that the device is given the default platform data
+ * as the driver will no longer carry defaults.
+ */
+extern void s3c_i2c0_set_platdata(struct s3c2410_platform_i2c *i2c);
+extern void s3c_i2c1_set_platdata(struct s3c2410_platform_i2c *i2c);
+extern void s3c_i2c2_set_platdata(struct s3c2410_platform_i2c *i2c);
+extern void s3c_i2c3_set_platdata(struct s3c2410_platform_i2c *i2c);
+extern void s3c_i2c4_set_platdata(struct s3c2410_platform_i2c *i2c);
+extern void s3c_i2c5_set_platdata(struct s3c2410_platform_i2c *i2c);
+extern void s3c_i2c6_set_platdata(struct s3c2410_platform_i2c *i2c);
+extern void s3c_i2c7_set_platdata(struct s3c2410_platform_i2c *i2c);
+extern void s5p_i2c_hdmiphy_set_platdata(struct s3c2410_platform_i2c *i2c);
+
+/* defined by architecture to configure gpio */
+extern void s3c_i2c0_cfg_gpio(struct platform_device *dev);
+extern void s3c_i2c1_cfg_gpio(struct platform_device *dev);
+extern void s3c_i2c2_cfg_gpio(struct platform_device *dev);
+extern void s3c_i2c3_cfg_gpio(struct platform_device *dev);
+extern void s3c_i2c4_cfg_gpio(struct platform_device *dev);
+extern void s3c_i2c5_cfg_gpio(struct platform_device *dev);
+extern void s3c_i2c6_cfg_gpio(struct platform_device *dev);
+extern void s3c_i2c7_cfg_gpio(struct platform_device *dev);
+
+extern struct s3c2410_platform_i2c default_i2c_data;
+
+#endif /* __ASM_ARCH_IIC_H */
--- /dev/null
+#ifndef ASMARM_ARCH_IRDA_H
+#define ASMARM_ARCH_IRDA_H
+
+/* board specific transceiver capabilities */
+
+#define IR_OFF 1
+#define IR_SIRMODE 2
+#define IR_FIRMODE 4
+
+struct pxaficp_platform_data {
+ int transceiver_cap;
+ void (*transceiver_mode)(struct device *dev, int mode);
+ int (*startup)(struct device *dev);
+ void (*shutdown)(struct device *dev);
+ int gpio_pwdown; /* powerdown GPIO for the IrDA chip */
+ bool gpio_pwdown_inverted; /* gpio_pwdown is inverted */
+};
+
+extern void pxa_set_ficp_info(struct pxaficp_platform_data *info);
+
+#if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x)
+void pxa2xx_transceiver_mode(struct device *dev, int mode);
+#endif
+
+#endif
--- /dev/null
+#ifndef __ASM_ARCH_PXA930_ROTARY_H
+#define __ASM_ARCH_PXA930_ROTARY_H
+
+/* NOTE:
+ *
+ * rotary can be either interpreted as a ralative input event (e.g.
+ * REL_WHEEL or REL_HWHEEL) or a specific key event (e.g. UP/DOWN
+ * or LEFT/RIGHT), depending on if up_key & down_key are assigned
+ * or rel_code is assigned a non-zero value. When all are non-zero,
+ * up_key and down_key will be preferred.
+ */
+struct pxa930_rotary_platform_data {
+ int up_key;
+ int down_key;
+ int rel_code;
+};
+
+void __init pxa930_set_rotarykey_info(struct pxa930_rotary_platform_data *info);
+
+#endif /* __ASM_ARCH_PXA930_ROTARY_H */
--- /dev/null
+/*
+ * arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h
+ */
+
+#ifndef __ASM_ARCH_EP93XX_KEYPAD_H
+#define __ASM_ARCH_EP93XX_KEYPAD_H
+
+struct matrix_keymap_data;
+
+/* flags for the ep93xx_keypad driver */
+#define EP93XX_KEYPAD_DISABLE_3_KEY (1<<0) /* disable 3-key reset */
+#define EP93XX_KEYPAD_DIAG_MODE (1<<1) /* diagnostic mode */
+#define EP93XX_KEYPAD_BACK_DRIVE (1<<2) /* back driving mode */
+#define EP93XX_KEYPAD_TEST_MODE (1<<3) /* scan only column 0 */
+#define EP93XX_KEYPAD_KDIV (1<<4) /* 1/4 clock or 1/16 clock */
+#define EP93XX_KEYPAD_AUTOREPEAT (1<<5) /* enable key autorepeat */
+
+/**
+ * struct ep93xx_keypad_platform_data - platform specific device structure
+ * @keymap_data: pointer to &matrix_keymap_data
+ * @debounce: debounce start count; terminal count is 0xff
+ * @prescale: row/column counter pre-scaler load value
+ * @flags: see above
+ */
+struct ep93xx_keypad_platform_data {
+ struct matrix_keymap_data *keymap_data;
+ unsigned int debounce;
+ unsigned int prescale;
+ unsigned int flags;
+};
+
+#define EP93XX_MATRIX_ROWS (8)
+#define EP93XX_MATRIX_COLS (8)
+
+#endif /* __ASM_ARCH_EP93XX_KEYPAD_H */
--- /dev/null
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License Terms: GNU General Public License v2
+ * Author: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
+ *
+ * ux500 Scroll key and Keypad Encoder (SKE) header
+ */
+
+#ifndef __SKE_H
+#define __SKE_H
+
+#include <linux/input/matrix_keypad.h>
+
+/* register definitions for SKE peripheral */
+#define SKE_CR 0x00
+#define SKE_VAL0 0x04
+#define SKE_VAL1 0x08
+#define SKE_DBCR 0x0C
+#define SKE_IMSC 0x10
+#define SKE_RIS 0x14
+#define SKE_MIS 0x18
+#define SKE_ICR 0x1C
+
+/*
+ * Keypad module
+ */
+
+/**
+ * struct keypad_platform_data - structure for platform specific data
+ * @init: pointer to keypad init function
+ * @exit: pointer to keypad deinitialisation function
+ * @keymap_data: matrix scan code table for keycodes
+ * @krow: maximum number of rows
+ * @kcol: maximum number of columns
+ * @debounce_ms: platform specific debounce time
+ * @no_autorepeat: flag for auto repetition
+ * @wakeup_enable: allow waking up the system
+ */
+struct ske_keypad_platform_data {
+ int (*init)(void);
+ int (*exit)(void);
+ const struct matrix_keymap_data *keymap_data;
+ u8 krow;
+ u8 kcol;
+ u8 debounce_ms;
+ bool no_autorepeat;
+ bool wakeup_enable;
+};
+#endif /*__SKE_KPD_H*/
--- /dev/null
+#ifndef __ASM_ARCH_PXA27x_KEYPAD_H
+#define __ASM_ARCH_PXA27x_KEYPAD_H
+
+#include <linux/input.h>
+#include <linux/input/matrix_keypad.h>
+
+#define MAX_MATRIX_KEY_ROWS (8)
+#define MAX_MATRIX_KEY_COLS (8)
+#define MATRIX_ROW_SHIFT (3)
+#define MAX_DIRECT_KEY_NUM (8)
+
+/* pxa3xx keypad platform specific parameters
+ *
+ * NOTE:
+ * 1. direct_key_num indicates the number of keys in the direct keypad
+ * _plus_ the number of rotary-encoder sensor inputs, this can be
+ * left as 0 if only rotary encoders are enabled, the driver will
+ * automatically calculate this
+ *
+ * 2. direct_key_map is the key code map for the direct keys, if rotary
+ * encoder(s) are enabled, direct key 0/1(2/3) will be ignored
+ *
+ * 3. rotary can be either interpreted as a relative input event (e.g.
+ * REL_WHEEL/REL_HWHEEL) or specific keys (e.g. UP/DOWN/LEFT/RIGHT)
+ *
+ * 4. matrix key and direct key will use the same debounce_interval by
+ * default, which should be sufficient in most cases
+ *
+ * pxa168 keypad platform specific parameter
+ *
+ * NOTE:
+ * clear_wakeup_event callback is a workaround required to clear the
+ * keypad interrupt. The keypad wake must be cleared in addition to
+ * reading the MI/DI bits in the KPC register.
+ */
+struct pxa27x_keypad_platform_data {
+
+ /* code map for the matrix keys */
+ unsigned int matrix_key_rows;
+ unsigned int matrix_key_cols;
+ unsigned int *matrix_key_map;
+ int matrix_key_map_size;
+
+ /* direct keys */
+ int direct_key_num;
+ unsigned int direct_key_map[MAX_DIRECT_KEY_NUM];
+ /* the key output may be low active */
+ int direct_key_low_active;
+ /* give board a chance to choose the start direct key */
+ unsigned int direct_key_mask;
+
+ /* rotary encoders 0 */
+ int enable_rotary0;
+ int rotary0_rel_code;
+ int rotary0_up_key;
+ int rotary0_down_key;
+
+ /* rotary encoders 1 */
+ int enable_rotary1;
+ int rotary1_rel_code;
+ int rotary1_up_key;
+ int rotary1_down_key;
+
+ /* key debounce interval */
+ unsigned int debounce_interval;
+
+ /* clear wakeup event requirement for pxa168 */
+ void (*clear_wakeup_event)(void);
+};
+
+extern void pxa_set_keypad_info(struct pxa27x_keypad_platform_data *info);
+
+#endif /* __ASM_ARCH_PXA27x_KEYPAD_H */
--- /dev/null
+#ifndef __ASM_ARCH_W90P910_KEYPAD_H
+#define __ASM_ARCH_W90P910_KEYPAD_H
+
+#include <linux/input/matrix_keypad.h>
+
+extern void mfp_set_groupi(struct device *dev);
+
+struct w90p910_keypad_platform_data {
+ const struct matrix_keymap_data *keymap_data;
+
+ unsigned int prescale;
+ unsigned int debounce;
+};
+
+#endif /* __ASM_ARCH_W90P910_KEYPAD_H */
--- /dev/null
+/*
+ * Copyright (C) 2009 Texas Instruments, Inc
+ *
+ * Author: Miguel Aguilar <miguel.aguilar@ridgerun.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef DAVINCI_KEYSCAN_H
+#define DAVINCI_KEYSCAN_H
+
+#include <linux/io.h>
+
+enum davinci_matrix_types {
+ DAVINCI_KEYSCAN_MATRIX_4X4,
+ DAVINCI_KEYSCAN_MATRIX_5X3,
+};
+
+struct davinci_ks_platform_data {
+ int (*device_enable)(struct device *dev);
+ unsigned short *keymap;
+ u32 keymapsize;
+ u8 rep:1;
+ u8 strobe;
+ u8 interval;
+ u8 matrix_type;
+};
+
+#endif
+
--- /dev/null
+/*
+ * arch/arm/mach-kirkwood/include/mach/leds-netxbig.h
+ *
+ * Platform data structure for netxbig LED driver
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_LEDS_NETXBIG_H
+#define __MACH_LEDS_NETXBIG_H
+
+struct netxbig_gpio_ext {
+ unsigned *addr;
+ int num_addr;
+ unsigned *data;
+ int num_data;
+ unsigned enable;
+};
+
+enum netxbig_led_mode {
+ NETXBIG_LED_OFF,
+ NETXBIG_LED_ON,
+ NETXBIG_LED_SATA,
+ NETXBIG_LED_TIMER1,
+ NETXBIG_LED_TIMER2,
+ NETXBIG_LED_MODE_NUM,
+};
+
+#define NETXBIG_LED_INVALID_MODE NETXBIG_LED_MODE_NUM
+
+struct netxbig_led_timer {
+ unsigned long delay_on;
+ unsigned long delay_off;
+ enum netxbig_led_mode mode;
+};
+
+struct netxbig_led {
+ const char *name;
+ const char *default_trigger;
+ int mode_addr;
+ int *mode_val;
+ int bright_addr;
+};
+
+struct netxbig_led_platform_data {
+ struct netxbig_gpio_ext *gpio_ext;
+ struct netxbig_led_timer *timer;
+ int num_timer;
+ struct netxbig_led *leds;
+ int num_leds;
+};
+
+#endif /* __MACH_LEDS_NETXBIG_H */
--- /dev/null
+/*
+ * arch/arm/mach-kirkwood/include/mach/leds-ns2.h
+ *
+ * Platform data structure for Network Space v2 LED driver
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_LEDS_NS2_H
+#define __MACH_LEDS_NS2_H
+
+struct ns2_led {
+ const char *name;
+ const char *default_trigger;
+ unsigned cmd;
+ unsigned slow;
+};
+
+struct ns2_led_platform_data {
+ int num_leds;
+ struct ns2_led *leds;
+};
+
+#endif /* __MACH_LEDS_NS2_H */
--- /dev/null
+/* arch/arm/mach-s3c2410/include/mach/leds-gpio.h
+ *
+ * Copyright (c) 2006 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX - LEDs GPIO connector
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_LEDSGPIO_H
+#define __ASM_ARCH_LEDSGPIO_H "leds-gpio.h"
+
+#define S3C24XX_LEDF_ACTLOW (1<<0) /* LED is on when GPIO low */
+#define S3C24XX_LEDF_TRISTATE (1<<1) /* tristate to turn off */
+
+struct s3c24xx_led_platdata {
+ unsigned int gpio;
+ unsigned int flags;
+
+ char *name;
+ char *def_trigger;
+};
+
+#endif /* __ASM_ARCH_LEDSGPIO_H */
--- /dev/null
+/*
+ * arch/arm/mach-sa1100/include/mach/mcp.h
+ *
+ * Copyright (C) 2005 Russell King.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_ARM_ARCH_MCP_H
+#define __ASM_ARM_ARCH_MCP_H
+
+#include <linux/types.h>
+
+struct mcp_plat_data {
+ u32 mccr0;
+ u32 mccr1;
+ unsigned int sclk_rate;
+ void *codec_pdata;
+};
+
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2010-2011 Samsung Electronics Co., Ltd.
+ *
+ * S5P series MIPI CSI slave device support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __PLAT_SAMSUNG_MIPI_CSIS_H_
+#define __PLAT_SAMSUNG_MIPI_CSIS_H_ __FILE__
+
+struct platform_device;
+
+/**
+ * struct s5p_platform_mipi_csis - platform data for S5P MIPI-CSIS driver
+ * @clk_rate: bus clock frequency
+ * @lanes: number of data lanes used
+ * @alignment: data alignment in bits
+ * @hs_settle: HS-RX settle time
+ * @fixed_phy_vdd: false to enable external D-PHY regulator management in the
+ * driver or true in case this regulator has no enable function
+ * @phy_enable: pointer to a callback controlling D-PHY enable/reset
+ */
+struct s5p_platform_mipi_csis {
+ unsigned long clk_rate;
+ u8 lanes;
+ u8 alignment;
+ u8 hs_settle;
+ bool fixed_phy_vdd;
+ int (*phy_enable)(struct platform_device *pdev, bool on);
+};
+
+/**
+ * s5p_csis_phy_enable - global MIPI-CSI receiver D-PHY control
+ * @pdev: MIPI-CSIS platform device
+ * @on: true to enable D-PHY and deassert its reset
+ * false to disable D-PHY
+ */
+int s5p_csis_phy_enable(struct platform_device *pdev, bool on);
+
+#endif /* __PLAT_SAMSUNG_MIPI_CSIS_H_ */
--- /dev/null
+/*
+ * Board-specific MMC configuration
+ */
+
+#ifndef _DAVINCI_MMC_H
+#define _DAVINCI_MMC_H
+
+#include <linux/types.h>
+#include <linux/mmc/host.h>
+
+struct davinci_mmc_config {
+ /* get_cd()/get_wp() may sleep */
+ int (*get_cd)(int module);
+ int (*get_ro)(int module);
+
+ void (*set_power)(int module, bool on);
+
+ /* wires == 0 is equivalent to wires == 4 (4-bit parallel) */
+ u8 wires;
+
+ u32 max_freq;
+
+ /* any additional host capabilities: OR'd in to mmc->f_caps */
+ u32 caps;
+
+ /* Version of the MMC/SD controller */
+ u8 version;
+
+ /* Number of sg segments */
+ u8 nr_sg;
+};
+void davinci_setup_mmc(int module, struct davinci_mmc_config *config);
+
+enum {
+ MMC_CTLR_VERSION_1 = 0, /* DM644x and DM355 */
+ MMC_CTLR_VERSION_2, /* DA830 */
+};
+
+#endif
--- /dev/null
+/*
+ * Copyright 2010 Wolfram Sang <w.sang@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2
+ * of the License.
+ */
+
+#ifndef __ASM_ARCH_IMX_ESDHC_H
+#define __ASM_ARCH_IMX_ESDHC_H
+
+enum wp_types {
+ ESDHC_WP_NONE, /* no WP, neither controller nor gpio */
+ ESDHC_WP_CONTROLLER, /* mmc controller internal WP */
+ ESDHC_WP_GPIO, /* external gpio pin for WP */
+};
+
+enum cd_types {
+ ESDHC_CD_NONE, /* no CD, neither controller nor gpio */
+ ESDHC_CD_CONTROLLER, /* mmc controller internal CD */
+ ESDHC_CD_GPIO, /* external gpio pin for CD */
+ ESDHC_CD_PERMANENT, /* no CD, card permanently wired to host */
+};
+
+/**
+ * struct esdhc_platform_data - platform data for esdhc on i.MX
+ *
+ * ESDHC_WP(CD)_CONTROLLER type is not available on i.MX25/35.
+ *
+ * @wp_gpio: gpio for write_protect
+ * @cd_gpio: gpio for card_detect interrupt
+ * @wp_type: type of write_protect method (see wp_types enum above)
+ * @cd_type: type of card_detect method (see cd_types enum above)
+ */
+
+struct esdhc_platform_data {
+ unsigned int wp_gpio;
+ unsigned int cd_gpio;
+ enum wp_types wp_type;
+ enum cd_types cd_type;
+};
+#endif /* __ASM_ARCH_IMX_ESDHC_H */
--- /dev/null
+/*
+ * arch/arm/include/asm/mach/mmc.h
+ */
+#ifndef ASMARM_MACH_MMC_H
+#define ASMARM_MACH_MMC_H
+
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/sdio_func.h>
+
+struct msm_mmc_gpio {
+ unsigned no;
+ const char *name;
+};
+
+struct msm_mmc_gpio_data {
+ struct msm_mmc_gpio *gpio;
+ u8 size;
+};
+
+struct msm_mmc_platform_data {
+ unsigned int ocr_mask; /* available voltages */
+ u32 (*translate_vdd)(struct device *, unsigned int);
+ unsigned int (*status)(struct device *);
+ int (*register_status_notify)(void (*callback)(int card_present, void *dev_id), void *dev_id);
+ struct msm_mmc_gpio_data *gpio_data;
+ void (*init_card)(struct mmc_card *card);
+};
+
+#endif
--- /dev/null
+/*
+ * arch/arm/plat-orion/include/plat/mvsdio.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_MVSDIO_H
+#define __MACH_MVSDIO_H
+
+#include <linux/mbus.h>
+
+struct mvsdio_platform_data {
+ unsigned int clock;
+ int gpio_card_detect;
+ int gpio_write_protect;
+};
+
+#endif
--- /dev/null
+#ifndef ASMARM_ARCH_MMC_H
+#define ASMARM_ARCH_MMC_H
+
+#include <linux/mmc/host.h>
+
+struct device;
+
+/* board specific SDHC data, optional.
+ * If not present, a writable card with 3,3V is assumed.
+ */
+struct imxmmc_platform_data {
+ /* Return values for the get_ro callback should be:
+ * 0 for a read/write card
+ * 1 for a read-only card
+ * -ENOSYS when not supported (equal to NULL callback)
+ * or a negative errno value when something bad happened
+ */
+ int (*get_ro)(struct device *);
+
+ /* board specific hook to (de)initialize the SD slot.
+ * The board code can call 'handler' on a card detection
+ * change giving data as argument.
+ */
+ int (*init)(struct device *dev, irq_handler_t handler, void *data);
+ void (*exit)(struct device *dev, void *data);
+
+ /* available voltages. If not given, assume
+ * MMC_VDD_32_33 | MMC_VDD_33_34
+ */
+ unsigned int ocr_avail;
+
+ /* adjust slot voltage */
+ void (*setpower)(struct device *, unsigned int vdd);
+
+ /* enable card detect using DAT3 */
+ int dat3_card_detect;
+};
+
+#endif
--- /dev/null
+#ifndef ASMARM_ARCH_MMC_H
+#define ASMARM_ARCH_MMC_H
+
+#include <linux/mmc/host.h>
+#include <linux/interrupt.h>
+
+struct device;
+struct mmc_host;
+
+struct pxamci_platform_data {
+ unsigned int ocr_mask; /* available voltages */
+ unsigned long detect_delay_ms; /* delay in millisecond before detecting cards after interrupt */
+ int (*init)(struct device *, irq_handler_t , void *);
+ int (*get_ro)(struct device *);
+ void (*setpower)(struct device *, unsigned int);
+ void (*exit)(struct device *, void *);
+ int gpio_card_detect; /* gpio detecting card insertion */
+ int gpio_card_ro; /* gpio detecting read only toggle */
+ bool gpio_card_ro_invert; /* gpio ro is inverted */
+ int gpio_power; /* gpio powering up MMC bus */
+ bool gpio_power_invert; /* gpio power is inverted */
+};
+
+extern void pxa_set_mci_info(struct pxamci_platform_data *info);
+extern void pxa3xx_set_mci2_info(struct pxamci_platform_data *info);
+extern void pxa3xx_set_mci3_info(struct pxamci_platform_data *info);
+
+#endif
--- /dev/null
+#ifndef _ARCH_MCI_H
+#define _ARCH_MCI_H
+
+/**
+ * struct s3c24xx_mci_pdata - sd/mmc controller platform data
+ * @no_wprotect: Set this to indicate there is no write-protect switch.
+ * @no_detect: Set this if there is no detect switch.
+ * @wprotect_invert: Invert the default sense of the write protect switch.
+ * @detect_invert: Invert the default sense of the write protect switch.
+ * @use_dma: Set to allow the use of DMA.
+ * @gpio_detect: GPIO number for the card detect line.
+ * @gpio_wprotect: GPIO number for the write protect line.
+ * @ocr_avail: The mask of the available power states, non-zero to use.
+ * @set_power: Callback to control the power mode.
+ *
+ * The @gpio_detect is used for card detection when @no_wprotect is unset,
+ * and the default sense is that 0 returned from gpio_get_value() means
+ * that a card is inserted. If @detect_invert is set, then the value from
+ * gpio_get_value() is inverted, which makes 1 mean card inserted.
+ *
+ * The driver will use @gpio_wprotect to signal whether the card is write
+ * protected if @no_wprotect is not set. A 0 returned from gpio_get_value()
+ * means the card is read/write, and 1 means read-only. The @wprotect_invert
+ * will invert the value returned from gpio_get_value().
+ *
+ * Card power is set by @ocr_availa, using MCC_VDD_ constants if it is set
+ * to a non-zero value, otherwise the default of 3.2-3.4V is used.
+ */
+struct s3c24xx_mci_pdata {
+ unsigned int no_wprotect:1;
+ unsigned int no_detect:1;
+ unsigned int wprotect_invert:1;
+ unsigned int detect_invert:1; /* set => detect active high */
+ unsigned int use_dma:1;
+
+ unsigned int gpio_detect;
+ unsigned int gpio_wprotect;
+ unsigned long ocr_avail;
+ void (*set_power)(unsigned char power_mode,
+ unsigned short vdd);
+};
+
+/**
+ * s3c24xx_mci_set_platdata - set platform data for mmc/sdi device
+ * @pdata: The platform data
+ *
+ * Copy the platform data supplied by @pdata so that this can be marked
+ * __initdata.
+ */
+extern void s3c24xx_mci_set_platdata(struct s3c24xx_mci_pdata *pdata);
+
+#endif /* _ARCH_NCI_H */
--- /dev/null
+/*
+ * Copyright (C) 2009 Palm, Inc.
+ * Author: Yvonne Yip <y@palm.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+#ifndef __PLATFORM_DATA_TEGRA_SDHCI_H
+#define __PLATFORM_DATA_TEGRA_SDHCI_H
+
+#include <linux/mmc/host.h>
+
+struct tegra_sdhci_platform_data {
+ int cd_gpio;
+ int wp_gpio;
+ int power_gpio;
+ int is_8bit;
+ int pm_flags;
+};
+
+#endif
--- /dev/null
+#ifndef __ASM_ARCH_PXA930_TRKBALL_H
+#define __ASM_ARCH_PXA930_TRKBALL_H
+
+struct pxa930_trkball_platform_data {
+ int x_filter;
+ int y_filter;
+};
+
+#endif /* __ASM_ARCH_PXA930_TRKBALL_H */
+
--- /dev/null
+/*
+ * TI DaVinci AEMIF support
+ *
+ * Copyright 2010 (C) Texas Instruments, Inc. http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+#ifndef _MACH_DAVINCI_AEMIF_H
+#define _MACH_DAVINCI_AEMIF_H
+
+#define NRCSR_OFFSET 0x00
+#define AWCCR_OFFSET 0x04
+#define A1CR_OFFSET 0x10
+
+#define ACR_ASIZE_MASK 0x3
+#define ACR_EW_MASK BIT(30)
+#define ACR_SS_MASK BIT(31)
+
+/* All timings in nanoseconds */
+struct davinci_aemif_timing {
+ u8 wsetup;
+ u8 wstrobe;
+ u8 whold;
+
+ u8 rsetup;
+ u8 rstrobe;
+ u8 rhold;
+
+ u8 ta;
+};
+
+int davinci_aemif_setup_timing(struct davinci_aemif_timing *t,
+ void __iomem *base, unsigned cs);
+#endif
--- /dev/null
+/*
+ * mach-davinci/nand.h
+ *
+ * Copyright © 2006 Texas Instruments.
+ *
+ * Ported to 2.6.23 Copyright © 2008 by
+ * Sander Huijsen <Shuijsen@optelecom-nkf.com>
+ * Troy Kisky <troy.kisky@boundarydevices.com>
+ * Dirk Behme <Dirk.Behme@gmail.com>
+ *
+ * --------------------------------------------------------------------------
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ARCH_ARM_DAVINCI_NAND_H
+#define __ARCH_ARM_DAVINCI_NAND_H
+
+#include <linux/mtd/nand.h>
+
+#define NANDFCR_OFFSET 0x60
+#define NANDFSR_OFFSET 0x64
+#define NANDF1ECC_OFFSET 0x70
+
+/* 4-bit ECC syndrome registers */
+#define NAND_4BIT_ECC_LOAD_OFFSET 0xbc
+#define NAND_4BIT_ECC1_OFFSET 0xc0
+#define NAND_4BIT_ECC2_OFFSET 0xc4
+#define NAND_4BIT_ECC3_OFFSET 0xc8
+#define NAND_4BIT_ECC4_OFFSET 0xcc
+#define NAND_ERR_ADD1_OFFSET 0xd0
+#define NAND_ERR_ADD2_OFFSET 0xd4
+#define NAND_ERR_ERRVAL1_OFFSET 0xd8
+#define NAND_ERR_ERRVAL2_OFFSET 0xdc
+
+/* NOTE: boards don't need to use these address bits
+ * for ALE/CLE unless they support booting from NAND.
+ * They're used unless platform data overrides them.
+ */
+#define MASK_ALE 0x08
+#define MASK_CLE 0x10
+
+struct davinci_nand_pdata { /* platform_data */
+ uint32_t mask_ale;
+ uint32_t mask_cle;
+
+ /* for packages using two chipselects */
+ uint32_t mask_chipsel;
+
+ /* board's default static partition info */
+ struct mtd_partition *parts;
+ unsigned nr_parts;
+
+ /* none == NAND_ECC_NONE (strongly *not* advised!!)
+ * soft == NAND_ECC_SOFT
+ * else == NAND_ECC_HW, according to ecc_bits
+ *
+ * All DaVinci-family chips support 1-bit hardware ECC.
+ * Newer ones also support 4-bit ECC, but are awkward
+ * using it with large page chips.
+ */
+ nand_ecc_modes_t ecc_mode;
+ u8 ecc_bits;
+
+ /* e.g. NAND_BUSWIDTH_16 */
+ unsigned options;
+ /* e.g. NAND_BBT_USE_FLASH */
+ unsigned bbt_options;
+
+ /* Main and mirror bbt descriptor overrides */
+ struct nand_bbt_descr *bbt_td;
+ struct nand_bbt_descr *bbt_md;
+
+ /* Access timings */
+ struct davinci_aemif_timing *timing;
+};
+
+#endif /* __ARCH_ARM_DAVINCI_NAND_H */
--- /dev/null
+/*
+ * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2008 Sascha Hauer, kernel@pengutronix.de
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#ifndef __ASM_ARCH_NAND_H
+#define __ASM_ARCH_NAND_H
+
+#include <linux/mtd/partitions.h>
+
+struct mxc_nand_platform_data {
+ unsigned int width; /* data bus width in bytes */
+ unsigned int hw_ecc:1; /* 0 if suppress hardware ECC */
+ unsigned int flash_bbt:1; /* set to 1 to use a flash based bbt */
+ struct mtd_partition *parts; /* partition table */
+ int nr_parts; /* size of parts */
+};
+#endif /* __ASM_ARCH_NAND_H */
--- /dev/null
+#ifndef __ASM_ARCH_PXA3XX_NAND_H
+#define __ASM_ARCH_PXA3XX_NAND_H
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+struct pxa3xx_nand_timing {
+ unsigned int tCH; /* Enable signal hold time */
+ unsigned int tCS; /* Enable signal setup time */
+ unsigned int tWH; /* ND_nWE high duration */
+ unsigned int tWP; /* ND_nWE pulse time */
+ unsigned int tRH; /* ND_nRE high duration */
+ unsigned int tRP; /* ND_nRE pulse width */
+ unsigned int tR; /* ND_nWE high to ND_nRE low for read */
+ unsigned int tWHR; /* ND_nWE high to ND_nRE low for status read */
+ unsigned int tAR; /* ND_ALE low to ND_nRE low delay */
+};
+
+struct pxa3xx_nand_cmdset {
+ uint16_t read1;
+ uint16_t read2;
+ uint16_t program;
+ uint16_t read_status;
+ uint16_t read_id;
+ uint16_t erase;
+ uint16_t reset;
+ uint16_t lock;
+ uint16_t unlock;
+ uint16_t lock_status;
+};
+
+struct pxa3xx_nand_flash {
+ char *name;
+ uint32_t chip_id;
+ unsigned int page_per_block; /* Pages per block (PG_PER_BLK) */
+ unsigned int page_size; /* Page size in bytes (PAGE_SZ) */
+ unsigned int flash_width; /* Width of Flash memory (DWIDTH_M) */
+ unsigned int dfc_width; /* Width of flash controller(DWIDTH_C) */
+ unsigned int num_blocks; /* Number of physical blocks in Flash */
+
+ struct pxa3xx_nand_timing *timing; /* NAND Flash timing */
+};
+
+/*
+ * Current pxa3xx_nand controller has two chip select which
+ * both be workable.
+ *
+ * Notice should be taken that:
+ * When you want to use this feature, you should not enable the
+ * keep configuration feature, for two chip select could be
+ * attached with different nand chip. The different page size
+ * and timing requirement make the keep configuration impossible.
+ */
+
+/* The max num of chip select current support */
+#define NUM_CHIP_SELECT (2)
+struct pxa3xx_nand_platform_data {
+
+ /* the data flash bus is shared between the Static Memory
+ * Controller and the Data Flash Controller, the arbiter
+ * controls the ownership of the bus
+ */
+ int enable_arbiter;
+
+ /* allow platform code to keep OBM/bootloader defined NFC config */
+ int keep_config;
+
+ /* indicate how many chip selects will be used */
+ int num_cs;
+
+ const struct mtd_partition *parts[NUM_CHIP_SELECT];
+ unsigned int nr_parts[NUM_CHIP_SELECT];
+
+ const struct pxa3xx_nand_flash * flash;
+ size_t num_flash;
+};
+
+extern void pxa3xx_set_nand_info(struct pxa3xx_nand_platform_data *info);
+#endif /* __ASM_ARCH_PXA3XX_NAND_H */
--- /dev/null
+/* arch/arm/mach-s3c2410/include/mach/nand.h
+ *
+ * Copyright (c) 2004 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 - NAND device controller platform_device info
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/**
+ * struct s3c2410_nand_set - define a set of one or more nand chips
+ * @disable_ecc: Entirely disable ECC - Dangerous
+ * @flash_bbt: Openmoko u-boot can create a Bad Block Table
+ * Setting this flag will allow the kernel to
+ * look for it at boot time and also skip the NAND
+ * scan.
+ * @options: Default value to set into 'struct nand_chip' options.
+ * @nr_chips: Number of chips in this set
+ * @nr_partitions: Number of partitions pointed to by @partitions
+ * @name: Name of set (optional)
+ * @nr_map: Map for low-layer logical to physical chip numbers (option)
+ * @partitions: The mtd partition list
+ *
+ * define a set of one or more nand chips registered with an unique mtd. Also
+ * allows to pass flag to the underlying NAND layer. 'disable_ecc' will trigger
+ * a warning at boot time.
+ */
+struct s3c2410_nand_set {
+ unsigned int disable_ecc:1;
+ unsigned int flash_bbt:1;
+
+ unsigned int options;
+ int nr_chips;
+ int nr_partitions;
+ char *name;
+ int *nr_map;
+ struct mtd_partition *partitions;
+ struct nand_ecclayout *ecc_layout;
+};
+
+struct s3c2410_platform_nand {
+ /* timing information for controller, all times in nanoseconds */
+
+ int tacls; /* time for active CLE/ALE to nWE/nOE */
+ int twrph0; /* active time for nWE/nOE */
+ int twrph1; /* time for release CLE/ALE from nWE/nOE inactive */
+
+ unsigned int ignore_unset_ecc:1;
+
+ int nr_sets;
+ struct s3c2410_nand_set *sets;
+
+ void (*select_chip)(struct s3c2410_nand_set *,
+ int chip);
+};
+
+/**
+ * s3c_nand_set_platdata() - register NAND platform data.
+ * @nand: The NAND platform data to register with s3c_device_nand.
+ *
+ * This function copies the given NAND platform data, @nand and registers
+ * it with the s3c_device_nand. This allows @nand to be __initdata.
+*/
+extern void s3c_nand_set_platdata(struct s3c2410_platform_nand *nand);
--- /dev/null
+#ifndef __ASM_ARCH_NAND_H
+#define __ASM_ARCH_NAND_H
+
+struct nomadik_nand_platform_data {
+ struct mtd_partition *parts;
+ int nparts;
+ int options;
+ int (*init) (void);
+ int (*exit) (void);
+};
+
+#define NAND_IO_DATA 0x40000000
+#define NAND_IO_CMD 0x40800000
+#define NAND_IO_ADDR 0x41000000
+
+#endif /* __ASM_ARCH_NAND_H */
--- /dev/null
+/*
+ * arch/arm/plat-orion/include/plat/orion_nand.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __PLAT_ORION_NAND_H
+#define __PLAT_ORION_NAND_H
+
+/*
+ * Device bus NAND private data
+ */
+struct orion_nand_data {
+ struct mtd_partition *parts;
+ int (*dev_ready)(struct mtd_info *mtd);
+ u32 nr_parts;
+ u8 ale; /* address line number connected to ALE */
+ u8 cle; /* address line number connected to CLE */
+ u8 width; /* buswidth */
+ u8 chip_delay;
+};
+
+
+#endif
--- /dev/null
+#ifndef __ARCOM_PCMCIA_H
+#define __ARCOM_PCMCIA_H
+
+struct arcom_pcmcia_pdata {
+ int cd_gpio;
+ int rdy_gpio;
+ int pwr_gpio;
+ void (*reset)(int state);
+};
+
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#ifndef ASMARM_ARCH_UART_H
+#define ASMARM_ARCH_UART_H
+
+#define IMXUART_HAVE_RTSCTS (1<<0)
+#define IMXUART_IRDA (1<<1)
+
+struct imxuart_platform_data {
+ int (*init)(struct platform_device *pdev);
+ void (*exit)(struct platform_device *pdev);
+ unsigned int flags;
+ void (*irda_enable)(int enable);
+ unsigned int irda_inv_rx:1;
+ unsigned int irda_inv_tx:1;
+ unsigned short transceiver_delay;
+};
+
+#endif
--- /dev/null
+/*
+ * Copyright 2009 Texas Instruments.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ARCH_ARM_DAVINCI_SPI_H
+#define __ARCH_ARM_DAVINCI_SPI_H
+
+#include <mach/edma.h>
+
+#define SPI_INTERN_CS 0xFF
+
+enum {
+ SPI_VERSION_1, /* For DM355/DM365/DM6467 */
+ SPI_VERSION_2, /* For DA8xx */
+};
+
+/**
+ * davinci_spi_platform_data - Platform data for SPI master device on DaVinci
+ *
+ * @version: version of the SPI IP. Different DaVinci devices have slightly
+ * varying versions of the same IP.
+ * @num_chipselect: number of chipselects supported by this SPI master
+ * @intr_line: interrupt line used to connect the SPI IP to the ARM interrupt
+ * controller withn the SoC. Possible values are 0 and 1.
+ * @chip_sel: list of GPIOs which can act as chip-selects for the SPI.
+ * SPI_INTERN_CS denotes internal SPI chip-select. Not necessary
+ * to populate if all chip-selects are internal.
+ * @cshold_bug: set this to true if the SPI controller on your chip requires
+ * a write to CSHOLD bit in between transfers (like in DM355).
+ * @dma_event_q: DMA event queue to use if SPI_IO_TYPE_DMA is used for any
+ * device on the bus.
+ */
+struct davinci_spi_platform_data {
+ u8 version;
+ u8 num_chipselect;
+ u8 intr_line;
+ u8 *chip_sel;
+ bool cshold_bug;
+ enum dma_event_q dma_event_q;
+};
+
+/**
+ * davinci_spi_config - Per-chip-select configuration for SPI slave devices
+ *
+ * @wdelay: amount of delay between transmissions. Measured in number of
+ * SPI module clocks.
+ * @odd_parity: polarity of parity flag at the end of transmit data stream.
+ * 0 - odd parity, 1 - even parity.
+ * @parity_enable: enable transmission of parity at end of each transmit
+ * data stream.
+ * @io_type: type of IO transfer. Choose between polled, interrupt and DMA.
+ * @timer_disable: disable chip-select timers (setup and hold)
+ * @c2tdelay: chip-select setup time. Measured in number of SPI module clocks.
+ * @t2cdelay: chip-select hold time. Measured in number of SPI module clocks.
+ * @t2edelay: transmit data finished to SPI ENAn pin inactive time. Measured
+ * in number of SPI clocks.
+ * @c2edelay: chip-select active to SPI ENAn signal active time. Measured in
+ * number of SPI clocks.
+ */
+struct davinci_spi_config {
+ u8 wdelay;
+ u8 odd_parity;
+ u8 parity_enable;
+#define SPI_IO_TYPE_INTR 0
+#define SPI_IO_TYPE_POLL 1
+#define SPI_IO_TYPE_DMA 2
+ u8 io_type;
+ u8 timer_disable;
+ u8 c2tdelay;
+ u8 t2cdelay;
+ u8 t2edelay;
+ u8 c2edelay;
+};
+
+#endif /* __ARCH_ARM_DAVINCI_SPI_H */
--- /dev/null
+#ifndef __ASM_MACH_EP93XX_SPI_H
+#define __ASM_MACH_EP93XX_SPI_H
+
+struct spi_device;
+
+/**
+ * struct ep93xx_spi_info - EP93xx specific SPI descriptor
+ * @num_chipselect: number of chip selects on this board, must be
+ * at least one
+ * @use_dma: use DMA for the transfers
+ */
+struct ep93xx_spi_info {
+ int num_chipselect;
+ bool use_dma;
+};
+
+/**
+ * struct ep93xx_spi_chip_ops - operation callbacks for SPI slave device
+ * @setup: setup the chip select mechanism
+ * @cleanup: cleanup the chip select mechanism
+ * @cs_control: control the device chip select
+ */
+struct ep93xx_spi_chip_ops {
+ int (*setup)(struct spi_device *spi);
+ void (*cleanup)(struct spi_device *spi);
+ void (*cs_control)(struct spi_device *spi, int value);
+};
+
+#endif /* __ASM_MACH_EP93XX_SPI_H */
--- /dev/null
+
+#ifndef __MACH_SPI_H_
+#define __MACH_SPI_H_
+
+/*
+ * struct spi_imx_master - device.platform_data for SPI controller devices.
+ * @chipselect: Array of chipselects for this master. Numbers >= 0 mean gpio
+ * pins, numbers < 0 mean internal CSPI chipselects according
+ * to MXC_SPI_CS(). Normally you want to use gpio based chip
+ * selects as the CSPI module tries to be intelligent about
+ * when to assert the chipselect: The CSPI module deasserts the
+ * chipselect once it runs out of input data. The other problem
+ * is that it is not possible to mix between high active and low
+ * active chipselects on one single bus using the internal
+ * chipselects. Unfortunately Freescale decided to put some
+ * chipselects on dedicated pins which are not usable as gpios,
+ * so we have to support the internal chipselects.
+ * @num_chipselect: ARRAY_SIZE(chipselect)
+ */
+struct spi_imx_master {
+ int *chipselect;
+ int num_chipselect;
+};
+
+#define MXC_SPI_CS(no) ((no) - 32)
+
+#endif /* __MACH_SPI_H_*/
--- /dev/null
+/*
+ * arch/arm/mach-w90x900/include/mach/nuc900_spi.h
+ *
+ * Copyright (c) 2009 Nuvoton technology corporation.
+ *
+ * Wan ZongShun <mcuos.com@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation;version 2 of the License.
+ *
+ */
+
+#ifndef __ASM_ARCH_SPI_H
+#define __ASM_ARCH_SPI_H
+
+extern void mfp_set_groupg(struct device *dev, const char *subname);
+
+struct nuc900_spi_info {
+ unsigned int num_cs;
+ unsigned int lsb;
+ unsigned int txneg;
+ unsigned int rxneg;
+ unsigned int divider;
+ unsigned int sleep;
+ unsigned int txnum;
+ unsigned int txbitlen;
+ int bus_num;
+};
+
+struct nuc900_spi_chip {
+ unsigned char bits_per_word;
+};
+
+#endif /* __ASM_ARCH_SPI_H */
--- /dev/null
+/* linux/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
+ *
+ * Copyright (C) 2009 Samsung Electronics Ltd.
+ * Jaswinder Singh <jassi.brar@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __S3C64XX_PLAT_SPI_H
+#define __S3C64XX_PLAT_SPI_H
+
+struct platform_device;
+
+/**
+ * struct s3c64xx_spi_csinfo - ChipSelect description
+ * @fb_delay: Slave specific feedback delay.
+ * Refer to FB_CLK_SEL register definition in SPI chapter.
+ * @line: Custom 'identity' of the CS line.
+ *
+ * This is per SPI-Slave Chipselect information.
+ * Allocate and initialize one in machine init code and make the
+ * spi_board_info.controller_data point to it.
+ */
+struct s3c64xx_spi_csinfo {
+ u8 fb_delay;
+ unsigned line;
+};
+
+/**
+ * struct s3c64xx_spi_info - SPI Controller defining structure
+ * @src_clk_nr: Clock source index for the CLK_CFG[SPI_CLKSEL] field.
+ * @num_cs: Number of CS this controller emulates.
+ * @cfg_gpio: Configure pins for this SPI controller.
+ */
+struct s3c64xx_spi_info {
+ int src_clk_nr;
+ int num_cs;
+ int (*cfg_gpio)(void);
+};
+
+/**
+ * s3c64xx_spi_set_platdata - SPI Controller configure callback by the board
+ * initialization code.
+ * @cfg_gpio: Pointer to gpio setup function.
+ * @src_clk_nr: Clock the SPI controller is to use to generate SPI clocks.
+ * @num_cs: Number of elements in the 'cs' array.
+ *
+ * Call this from machine init code for each SPI Controller that
+ * has some chips attached to it.
+ */
+extern void s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+ int num_cs);
+extern void s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+ int num_cs);
+extern void s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+ int num_cs);
+
+/* defined by architecture to configure gpio */
+extern int s3c64xx_spi0_cfg_gpio(void);
+extern int s3c64xx_spi1_cfg_gpio(void);
+extern int s3c64xx_spi2_cfg_gpio(void);
+
+extern struct s3c64xx_spi_info s3c64xx_spi0_pdata;
+extern struct s3c64xx_spi_info s3c64xx_spi1_pdata;
+extern struct s3c64xx_spi_info s3c64xx_spi2_pdata;
+#endif /* __S3C64XX_PLAT_SPI_H */
--- /dev/null
+/* arch/arm/plat-samsung/include/plat/ts.h
+ *
+ * Copyright (c) 2005 Arnaud Patard <arnaud.patard@rtp-net.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARM_TS_H
+#define __ASM_ARM_TS_H
+
+struct s3c2410_ts_mach_info {
+ int delay;
+ int presc;
+ int oversampling_shift;
+ void (*cfg_gpio)(struct platform_device *dev);
+};
+
+extern void s3c24xx_ts_set_platdata(struct s3c2410_ts_mach_info *);
+
+/* defined by architecture to configure gpio */
+extern void s3c24xx_ts_cfg_gpio(struct platform_device *dev);
+
+#endif /* __ASM_ARM_TS_H */
--- /dev/null
+/*
+ * USB related definitions
+ *
+ * Copyright (C) 2009 MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_USB_H
+#define __ASM_ARCH_USB_H
+
+/* DA8xx CFGCHIP2 (USB 2.0 PHY Control) register bits */
+#define CFGCHIP2_PHYCLKGD (1 << 17)
+#define CFGCHIP2_VBUSSENSE (1 << 16)
+#define CFGCHIP2_RESET (1 << 15)
+#define CFGCHIP2_OTGMODE (3 << 13)
+#define CFGCHIP2_NO_OVERRIDE (0 << 13)
+#define CFGCHIP2_FORCE_HOST (1 << 13)
+#define CFGCHIP2_FORCE_DEVICE (2 << 13)
+#define CFGCHIP2_FORCE_HOST_VBUS_LOW (3 << 13)
+#define CFGCHIP2_USB1PHYCLKMUX (1 << 12)
+#define CFGCHIP2_USB2PHYCLKMUX (1 << 11)
+#define CFGCHIP2_PHYPWRDN (1 << 10)
+#define CFGCHIP2_OTGPWRDN (1 << 9)
+#define CFGCHIP2_DATPOL (1 << 8)
+#define CFGCHIP2_USB1SUSPENDM (1 << 7)
+#define CFGCHIP2_PHY_PLLON (1 << 6) /* override PLL suspend */
+#define CFGCHIP2_SESENDEN (1 << 5) /* Vsess_end comparator */
+#define CFGCHIP2_VBDTCTEN (1 << 4) /* Vbus comparator */
+#define CFGCHIP2_REFFREQ (0xf << 0)
+#define CFGCHIP2_REFFREQ_12MHZ (1 << 0)
+#define CFGCHIP2_REFFREQ_24MHZ (2 << 0)
+#define CFGCHIP2_REFFREQ_48MHZ (3 << 0)
+
+struct da8xx_ohci_root_hub;
+
+typedef void (*da8xx_ocic_handler_t)(struct da8xx_ohci_root_hub *hub,
+ unsigned port);
+
+/* Passed as the platform data to the OHCI driver */
+struct da8xx_ohci_root_hub {
+ /* Switch the port power on/off */
+ int (*set_power)(unsigned port, int on);
+ /* Read the port power status */
+ int (*get_power)(unsigned port);
+ /* Read the port over-current indicator */
+ int (*get_oci)(unsigned port);
+ /* Over-current indicator change notification (pass NULL to disable) */
+ int (*ocic_notify)(da8xx_ocic_handler_t handler);
+
+ /* Time from power on to power good (in 2 ms units) */
+ u8 potpgt;
+};
+
+void davinci_setup_usb(unsigned mA, unsigned potpgt_ms);
+
+#endif /* ifndef __ASM_ARCH_USB_H */
--- /dev/null
+#ifndef __INCLUDE_ASM_ARCH_MXC_EHCI_H
+#define __INCLUDE_ASM_ARCH_MXC_EHCI_H
+
+/* values for portsc field */
+#define MXC_EHCI_PHY_LOW_POWER_SUSPEND (1 << 23)
+#define MXC_EHCI_FORCE_FS (1 << 24)
+#define MXC_EHCI_UTMI_8BIT (0 << 28)
+#define MXC_EHCI_UTMI_16BIT (1 << 28)
+#define MXC_EHCI_SERIAL (1 << 29)
+#define MXC_EHCI_MODE_UTMI (0 << 30)
+#define MXC_EHCI_MODE_PHILIPS (1 << 30)
+#define MXC_EHCI_MODE_ULPI (2 << 30)
+#define MXC_EHCI_MODE_SERIAL (3 << 30)
+
+/* values for flags field */
+#define MXC_EHCI_INTERFACE_DIFF_UNI (0 << 0)
+#define MXC_EHCI_INTERFACE_DIFF_BI (1 << 0)
+#define MXC_EHCI_INTERFACE_SINGLE_UNI (2 << 0)
+#define MXC_EHCI_INTERFACE_SINGLE_BI (3 << 0)
+#define MXC_EHCI_INTERFACE_MASK (0xf)
+
+#define MXC_EHCI_POWER_PINS_ENABLED (1 << 5)
+#define MXC_EHCI_PWR_PIN_ACTIVE_HIGH (1 << 6)
+#define MXC_EHCI_OC_PIN_ACTIVE_LOW (1 << 7)
+#define MXC_EHCI_TTL_ENABLED (1 << 8)
+
+#define MXC_EHCI_INTERNAL_PHY (1 << 9)
+#define MXC_EHCI_IPPUE_DOWN (1 << 10)
+#define MXC_EHCI_IPPUE_UP (1 << 11)
+#define MXC_EHCI_WAKEUP_ENABLED (1 << 12)
+#define MXC_EHCI_ITC_NO_THRESHOLD (1 << 13)
+
+#define MXC_USBCTRL_OFFSET 0
+#define MXC_USB_PHY_CTR_FUNC_OFFSET 0x8
+#define MXC_USB_PHY_CTR_FUNC2_OFFSET 0xc
+#define MXC_USBH2CTRL_OFFSET 0x14
+
+#define MX5_USBOTHER_REGS_OFFSET 0x800
+
+/* USB_PHY_CTRL_FUNC2*/
+#define MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK 0x3
+#define MX5_USB_UTMI_PHYCTRL1_PLLDIV_SHIFT 0
+
+struct mxc_usbh_platform_data {
+ int (*init)(struct platform_device *pdev);
+ int (*exit)(struct platform_device *pdev);
+
+ unsigned int portsc;
+ struct usb_phy *otg;
+};
+
+int mx51_initialize_usb_hw(int port, unsigned int flags);
+int mx25_initialize_usb_hw(int port, unsigned int flags);
+int mx31_initialize_usb_hw(int port, unsigned int flags);
+int mx35_initialize_usb_hw(int port, unsigned int flags);
+int mx27_initialize_usb_hw(int port, unsigned int flags);
+
+#endif /* __INCLUDE_ASM_ARCH_MXC_EHCI_H */
+
--- /dev/null
+/*
+ * arch/arm/plat-orion/include/plat/ehci-orion.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __PLAT_EHCI_ORION_H
+#define __PLAT_EHCI_ORION_H
+
+#include <linux/mbus.h>
+
+enum orion_ehci_phy_ver {
+ EHCI_PHY_ORION,
+ EHCI_PHY_DD,
+ EHCI_PHY_KW,
+ EHCI_PHY_NA,
+};
+
+struct orion_ehci_data {
+ enum orion_ehci_phy_ver phy_version;
+};
+
+
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2011 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __PLAT_SAMSUNG_EHCI_H
+#define __PLAT_SAMSUNG_EHCI_H __FILE__
+
+struct s5p_ehci_platdata {
+ int (*phy_init)(struct platform_device *pdev, int type);
+ int (*phy_exit)(struct platform_device *pdev, int type);
+};
+
+extern void s5p_ehci_set_platdata(struct s5p_ehci_platdata *pd);
+
+#endif /* __PLAT_SAMSUNG_EHCI_H */
--- /dev/null
+/*
+ * Copyright (C) 2011 Samsung Electronics Co.Ltd
+ * http://www.samsung.com/
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __MACH_EXYNOS_OHCI_H
+#define __MACH_EXYNOS_OHCI_H
+
+struct exynos4_ohci_platdata {
+ int (*phy_init)(struct platform_device *pdev, int type);
+ int (*phy_exit)(struct platform_device *pdev, int type);
+};
+
+extern void exynos4_ohci_set_platdata(struct exynos4_ohci_platdata *pd);
+
+#endif /* __MACH_EXYNOS_OHCI_H */
--- /dev/null
+/*
+ * Copyright (C) 2008 Darius Augulis <augulis.darius@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_MXC_USB
+#define __ASM_ARCH_MXC_USB
+
+struct imxusb_platform_data {
+ int (*init)(struct device *);
+ void (*exit)(struct device *);
+};
+
+#endif /* __ASM_ARCH_MXC_USB */
--- /dev/null
+/*
+ * Copyright (C) ST-Ericsson SA 2011
+ *
+ * Author: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#ifndef __ASM_ARCH_USB_H
+#define __ASM_ARCH_USB_H
+
+#include <linux/dmaengine.h>
+
+#define UX500_MUSB_DMA_NUM_RX_CHANNELS 8
+#define UX500_MUSB_DMA_NUM_TX_CHANNELS 8
+
+struct ux500_musb_board_data {
+ void **dma_rx_param_array;
+ void **dma_tx_param_array;
+ u32 num_rx_channels;
+ u32 num_tx_channels;
+ bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
+};
+
+void ux500_add_usb(struct device *parent, resource_size_t base,
+ int irq, int *dma_rx_cfg, int *dma_tx_cfg);
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2009 Martin Fuzzey <mfuzzey@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_MX21_USBH
+#define __ASM_ARCH_MX21_USBH
+
+enum mx21_usbh_xcvr {
+ /* Values below as used by hardware (HWMODE register) */
+ MX21_USBXCVR_TXDIF_RXDIF = 0,
+ MX21_USBXCVR_TXDIF_RXSE = 1,
+ MX21_USBXCVR_TXSE_RXDIF = 2,
+ MX21_USBXCVR_TXSE_RXSE = 3,
+};
+
+struct mx21_usbh_platform_data {
+ enum mx21_usbh_xcvr host_xcvr; /* tranceiver mode host 1,2 ports */
+ enum mx21_usbh_xcvr otg_xcvr; /* tranceiver mode otg (as host) port */
+ u16 enable_host1:1,
+ enable_host2:1,
+ enable_otg_host:1, /* enable "OTG" port (as host) */
+ host1_xcverless:1, /* traceiverless host1 port */
+ host1_txenoe:1, /* output enable host1 transmit enable */
+ otg_ext_xcvr:1, /* external tranceiver for OTG port */
+ unused:10;
+};
+
+#endif /* __ASM_ARCH_MX21_USBH */
--- /dev/null
+#ifndef ASMARM_ARCH_OHCI_H
+#define ASMARM_ARCH_OHCI_H
+
+struct device;
+
+struct pxaohci_platform_data {
+ int (*init)(struct device *);
+ void (*exit)(struct device *);
+
+ unsigned long flags;
+#define ENABLE_PORT1 (1 << 0)
+#define ENABLE_PORT2 (1 << 1)
+#define ENABLE_PORT3 (1 << 2)
+#define ENABLE_PORT_ALL (ENABLE_PORT1 | ENABLE_PORT2 | ENABLE_PORT3)
+
+#define POWER_SENSE_LOW (1 << 3)
+#define POWER_CONTROL_LOW (1 << 4)
+#define NO_OC_PROTECTION (1 << 5)
+#define OC_MODE_GLOBAL (0 << 6)
+#define OC_MODE_PERPORT (1 << 6)
+
+ int power_on_delay; /* Power On to Power Good time - in ms
+ * HCD must wait for this duration before
+ * accessing a powered on port
+ */
+ int port_mode;
+#define PMM_NPS_MODE 1
+#define PMM_GLOBAL_MODE 2
+#define PMM_PERPORT_MODE 3
+
+ int power_budget;
+};
+
+extern void pxa_set_ohci_info(struct pxaohci_platform_data *info);
+
+#endif
--- /dev/null
+/* arch/arm/plat-samsung/include/plat/usb-control.h
+ *
+ * Copyright (c) 2004 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C - USB host port information
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_USBCONTROL_H
+#define __ASM_ARCH_USBCONTROL_H
+
+#define S3C_HCDFLG_USED (1)
+
+struct s3c2410_hcd_port {
+ unsigned char flags;
+ unsigned char power;
+ unsigned char oc_status;
+ unsigned char oc_changed;
+};
+
+struct s3c2410_hcd_info {
+ struct usb_hcd *hcd;
+ struct s3c2410_hcd_port port[2];
+
+ void (*power_control)(int port, int to);
+ void (*enable_oc)(struct s3c2410_hcd_info *, int on);
+ void (*report_oc)(struct s3c2410_hcd_info *, int ports);
+};
+
+static void inline s3c2410_usb_report_oc(struct s3c2410_hcd_info *info, int ports)
+{
+ if (info->report_oc != NULL) {
+ (info->report_oc)(info, ports);
+ }
+}
+
+extern void s3c_ohci_set_platdata(struct s3c2410_hcd_info *info);
+
+#endif /*__ASM_ARCH_USBCONTROL_H */
--- /dev/null
+/*
+ * PXA3xx U2D header
+ *
+ * Copyright (C) 2010 CompuLab Ltd.
+ *
+ * Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __PXA310_U2D__
+#define __PXA310_U2D__
+
+#include <linux/usb/ulpi.h>
+
+struct pxa3xx_u2d_platform_data {
+
+#define ULPI_SER_6PIN (1 << 0)
+#define ULPI_SER_3PIN (1 << 1)
+ unsigned int ulpi_mode;
+
+ int (*init)(struct device *);
+ void (*exit)(struct device *);
+};
+
+
+/* Start PXA3xx U2D host */
+int pxa3xx_u2d_start_hc(struct usb_bus *host);
+/* Stop PXA3xx U2D host */
+void pxa3xx_u2d_stop_hc(struct usb_bus *host);
+
+extern void pxa3xx_set_u2d_info(struct pxa3xx_u2d_platform_data *info);
+
+#endif /* __PXA310_U2D__ */
--- /dev/null
+/* arch/arm/plat-samsung/include/plat/udc.h
+ *
+ * Copyright (c) 2005 Arnaud Patard <arnaud.patard@rtp-net.org>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *
+ * Changelog:
+ * 14-Mar-2005 RTP Created file
+ * 02-Aug-2005 RTP File rename
+ * 07-Sep-2005 BJD Minor cleanups, changed cmd to enum
+ * 18-Jan-2007 HMW Add per-platform vbus_draw function
+*/
+
+#ifndef __ASM_ARM_ARCH_UDC_H
+#define __ASM_ARM_ARCH_UDC_H
+
+enum s3c2410_udc_cmd_e {
+ S3C2410_UDC_P_ENABLE = 1, /* Pull-up enable */
+ S3C2410_UDC_P_DISABLE = 2, /* Pull-up disable */
+ S3C2410_UDC_P_RESET = 3, /* UDC reset, in case of */
+};
+
+struct s3c2410_udc_mach_info {
+ void (*udc_command)(enum s3c2410_udc_cmd_e);
+ void (*vbus_draw)(unsigned int ma);
+
+ unsigned int pullup_pin;
+ unsigned int pullup_pin_inverted;
+
+ unsigned int vbus_pin;
+ unsigned char vbus_pin_inverted;
+};
+
+extern void __init s3c24xx_udc_set_platdata(struct s3c2410_udc_mach_info *);
+
+struct s3c24xx_hsudc_platdata;
+
+extern void __init s3c24xx_hsudc_set_platdata(struct s3c24xx_hsudc_platdata *pd);
+
+#endif /* __ASM_ARM_ARCH_UDC_H */
--- /dev/null
+/*
+ * arch/arm/mach-ep93xx/include/mach/fb.h
+ */
+
+#ifndef __ASM_ARCH_EP93XXFB_H
+#define __ASM_ARCH_EP93XXFB_H
+
+struct platform_device;
+struct fb_videomode;
+struct fb_info;
+
+#define EP93XXFB_USE_MODEDB 0
+
+/* VideoAttributes flags */
+#define EP93XXFB_STATE_MACHINE_ENABLE (1 << 0)
+#define EP93XXFB_PIXEL_CLOCK_ENABLE (1 << 1)
+#define EP93XXFB_VSYNC_ENABLE (1 << 2)
+#define EP93XXFB_PIXEL_DATA_ENABLE (1 << 3)
+#define EP93XXFB_COMPOSITE_SYNC (1 << 4)
+#define EP93XXFB_SYNC_VERT_HIGH (1 << 5)
+#define EP93XXFB_SYNC_HORIZ_HIGH (1 << 6)
+#define EP93XXFB_SYNC_BLANK_HIGH (1 << 7)
+#define EP93XXFB_PCLK_FALLING (1 << 8)
+#define EP93XXFB_ENABLE_AC (1 << 9)
+#define EP93XXFB_ENABLE_LCD (1 << 10)
+#define EP93XXFB_ENABLE_CCIR (1 << 12)
+#define EP93XXFB_USE_PARALLEL_INTERFACE (1 << 13)
+#define EP93XXFB_ENABLE_INTERRUPT (1 << 14)
+#define EP93XXFB_USB_INTERLACE (1 << 16)
+#define EP93XXFB_USE_EQUALIZATION (1 << 17)
+#define EP93XXFB_USE_DOUBLE_HORZ (1 << 18)
+#define EP93XXFB_USE_DOUBLE_VERT (1 << 19)
+#define EP93XXFB_USE_BLANK_PIXEL (1 << 20)
+#define EP93XXFB_USE_SDCSN0 (0 << 21)
+#define EP93XXFB_USE_SDCSN1 (1 << 21)
+#define EP93XXFB_USE_SDCSN2 (2 << 21)
+#define EP93XXFB_USE_SDCSN3 (3 << 21)
+
+#define EP93XXFB_ENABLE (EP93XXFB_STATE_MACHINE_ENABLE | \
+ EP93XXFB_PIXEL_CLOCK_ENABLE | \
+ EP93XXFB_VSYNC_ENABLE | \
+ EP93XXFB_PIXEL_DATA_ENABLE)
+
+struct ep93xxfb_mach_info {
+ unsigned int num_modes;
+ const struct fb_videomode *modes;
+ const struct fb_videomode *default_mode;
+ int bpp;
+ unsigned int flags;
+
+ int (*setup)(struct platform_device *pdev);
+ void (*teardown)(struct platform_device *pdev);
+ void (*blank)(int blank_mode, struct fb_info *info);
+};
+
+#endif /* __ASM_ARCH_EP93XXFB_H */
--- /dev/null
+/*
+ * This structure describes the machine which we are running on.
+ */
+#ifndef __MACH_IMXFB_H__
+#define __MACH_IMXFB_H__
+
+#include <linux/fb.h>
+
+#define PCR_TFT (1 << 31)
+#define PCR_COLOR (1 << 30)
+#define PCR_PBSIZ_1 (0 << 28)
+#define PCR_PBSIZ_2 (1 << 28)
+#define PCR_PBSIZ_4 (2 << 28)
+#define PCR_PBSIZ_8 (3 << 28)
+#define PCR_BPIX_1 (0 << 25)
+#define PCR_BPIX_2 (1 << 25)
+#define PCR_BPIX_4 (2 << 25)
+#define PCR_BPIX_8 (3 << 25)
+#define PCR_BPIX_12 (4 << 25)
+#define PCR_BPIX_16 (5 << 25)
+#define PCR_BPIX_18 (6 << 25)
+#define PCR_PIXPOL (1 << 24)
+#define PCR_FLMPOL (1 << 23)
+#define PCR_LPPOL (1 << 22)
+#define PCR_CLKPOL (1 << 21)
+#define PCR_OEPOL (1 << 20)
+#define PCR_SCLKIDLE (1 << 19)
+#define PCR_END_SEL (1 << 18)
+#define PCR_END_BYTE_SWAP (1 << 17)
+#define PCR_REV_VS (1 << 16)
+#define PCR_ACD_SEL (1 << 15)
+#define PCR_ACD(x) (((x) & 0x7f) << 8)
+#define PCR_SCLK_SEL (1 << 7)
+#define PCR_SHARP (1 << 6)
+#define PCR_PCD(x) ((x) & 0x3f)
+
+#define PWMR_CLS(x) (((x) & 0x1ff) << 16)
+#define PWMR_LDMSK (1 << 15)
+#define PWMR_SCR1 (1 << 10)
+#define PWMR_SCR0 (1 << 9)
+#define PWMR_CC_EN (1 << 8)
+#define PWMR_PW(x) ((x) & 0xff)
+
+#define LSCR1_PS_RISE_DELAY(x) (((x) & 0x7f) << 26)
+#define LSCR1_CLS_RISE_DELAY(x) (((x) & 0x3f) << 16)
+#define LSCR1_REV_TOGGLE_DELAY(x) (((x) & 0xf) << 8)
+#define LSCR1_GRAY2(x) (((x) & 0xf) << 4)
+#define LSCR1_GRAY1(x) (((x) & 0xf))
+
+#define DMACR_BURST (1 << 31)
+#define DMACR_HM(x) (((x) & 0xf) << 16)
+#define DMACR_TM(x) ((x) & 0xf)
+
+struct imx_fb_videomode {
+ struct fb_videomode mode;
+ u32 pcr;
+ unsigned char bpp;
+};
+
+struct imx_fb_platform_data {
+ struct imx_fb_videomode *mode;
+ int num_modes;
+
+ u_int cmap_greyscale:1,
+ cmap_inverse:1,
+ cmap_static:1,
+ unused:29;
+
+ u_int pwmr;
+ u_int lscr1;
+ u_int dmacr;
+
+ u_char * fixed_screen_cpu;
+ dma_addr_t fixed_screen_dma;
+
+ int (*init)(struct platform_device *);
+ void (*exit)(struct platform_device *);
+
+ void (*lcd_power)(int);
+ void (*backlight_power)(int);
+};
+
+void set_imx_fb_info(struct imx_fb_platform_data *);
+#endif /* ifndef __MACH_IMXFB_H__ */
--- /dev/null
+/* arch/arm/mach-msm/include/mach/msm_fb.h
+ *
+ * Internal shared definitions for various MSM framebuffer parts.
+ *
+ * Copyright (C) 2007 Google Incorporated
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _MSM_FB_H_
+#define _MSM_FB_H_
+
+#include <linux/device.h>
+
+struct mddi_info;
+
+struct msm_fb_data {
+ int xres; /* x resolution in pixels */
+ int yres; /* y resolution in pixels */
+ int width; /* disply width in mm */
+ int height; /* display height in mm */
+ unsigned output_format;
+};
+
+struct msmfb_callback {
+ void (*func)(struct msmfb_callback *);
+};
+
+enum {
+ MSM_MDDI_PMDH_INTERFACE,
+ MSM_MDDI_EMDH_INTERFACE,
+ MSM_EBI2_INTERFACE,
+};
+
+#define MSMFB_CAP_PARTIAL_UPDATES (1 << 0)
+
+struct msm_panel_data {
+ /* turns off the fb memory */
+ int (*suspend)(struct msm_panel_data *);
+ /* turns on the fb memory */
+ int (*resume)(struct msm_panel_data *);
+ /* turns off the panel */
+ int (*blank)(struct msm_panel_data *);
+ /* turns on the panel */
+ int (*unblank)(struct msm_panel_data *);
+ void (*wait_vsync)(struct msm_panel_data *);
+ void (*request_vsync)(struct msm_panel_data *, struct msmfb_callback *);
+ void (*clear_vsync)(struct msm_panel_data *);
+ /* from the enum above */
+ unsigned interface_type;
+ /* data to be passed to the fb driver */
+ struct msm_fb_data *fb_data;
+
+ /* capabilities supported by the panel */
+ uint32_t caps;
+};
+
+struct msm_mddi_client_data {
+ void (*suspend)(struct msm_mddi_client_data *);
+ void (*resume)(struct msm_mddi_client_data *);
+ void (*activate_link)(struct msm_mddi_client_data *);
+ void (*remote_write)(struct msm_mddi_client_data *, uint32_t val,
+ uint32_t reg);
+ uint32_t (*remote_read)(struct msm_mddi_client_data *, uint32_t reg);
+ void (*auto_hibernate)(struct msm_mddi_client_data *, int);
+ /* custom data that needs to be passed from the board file to a
+ * particular client */
+ void *private_client_data;
+ struct resource *fb_resource;
+ /* from the list above */
+ unsigned interface_type;
+};
+
+struct msm_mddi_platform_data {
+ unsigned int clk_rate;
+ void (*power_client)(struct msm_mddi_client_data *, int on);
+
+ /* fixup the mfr name, product id */
+ void (*fixup)(uint16_t *mfr_name, uint16_t *product_id);
+
+ struct resource *fb_resource; /*optional*/
+ /* number of clients in the list that follows */
+ int num_clients;
+ /* array of client information of clients */
+ struct {
+ unsigned product_id; /* mfr id in top 16 bits, product id
+ * in lower 16 bits
+ */
+ char *name; /* the device name will be the platform
+ * device name registered for the client,
+ * it should match the name of the associated
+ * driver
+ */
+ unsigned id; /* id for mddi client device node, will also
+ * be used as device id of panel devices, if
+ * the client device will have multiple panels
+ * space must be left here for them
+ */
+ void *client_data; /* required private client data */
+ unsigned int clk_rate; /* optional: if the client requires a
+ * different mddi clk rate
+ */
+ } client_platform_data[];
+};
+
+struct mdp_blit_req;
+struct fb_info;
+struct mdp_device {
+ struct device dev;
+ void (*dma)(struct mdp_device *mpd, uint32_t addr,
+ uint32_t stride, uint32_t w, uint32_t h, uint32_t x,
+ uint32_t y, struct msmfb_callback *callback, int interface);
+ void (*dma_wait)(struct mdp_device *mdp);
+ int (*blit)(struct mdp_device *mdp, struct fb_info *fb,
+ struct mdp_blit_req *req);
+ void (*set_grp_disp)(struct mdp_device *mdp, uint32_t disp_id);
+};
+
+struct class_interface;
+int register_mdp_client(struct class_interface *class_intf);
+
+/**** private client data structs go below this line ***/
+
+struct msm_mddi_bridge_platform_data {
+ /* from board file */
+ int (*init)(struct msm_mddi_bridge_platform_data *,
+ struct msm_mddi_client_data *);
+ int (*uninit)(struct msm_mddi_bridge_platform_data *,
+ struct msm_mddi_client_data *);
+ /* passed to panel for use by the fb driver */
+ int (*blank)(struct msm_mddi_bridge_platform_data *,
+ struct msm_mddi_client_data *);
+ int (*unblank)(struct msm_mddi_bridge_platform_data *,
+ struct msm_mddi_client_data *);
+ struct msm_fb_data fb_data;
+};
+
+
+
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2008
+ * Guennadi Liakhovetski, DENX Software Engineering, <lg@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_MX3FB_H__
+#define __ASM_ARCH_MX3FB_H__
+
+#include <linux/device.h>
+#include <linux/fb.h>
+
+/* Proprietary FB_SYNC_ flags */
+#define FB_SYNC_OE_ACT_HIGH 0x80000000
+#define FB_SYNC_CLK_INVERT 0x40000000
+#define FB_SYNC_DATA_INVERT 0x20000000
+#define FB_SYNC_CLK_IDLE_EN 0x10000000
+#define FB_SYNC_SHARP_MODE 0x08000000
+#define FB_SYNC_SWAP_RGB 0x04000000
+#define FB_SYNC_CLK_SEL_EN 0x02000000
+
+/*
+ * Specify the way your display is connected. The IPU can arbitrarily
+ * map the internal colors to the external data lines. We only support
+ * the following mappings at the moment.
+ */
+enum disp_data_mapping {
+ /* blue -> d[0..5], green -> d[6..11], red -> d[12..17] */
+ IPU_DISP_DATA_MAPPING_RGB666,
+ /* blue -> d[0..4], green -> d[5..10], red -> d[11..15] */
+ IPU_DISP_DATA_MAPPING_RGB565,
+ /* blue -> d[0..7], green -> d[8..15], red -> d[16..23] */
+ IPU_DISP_DATA_MAPPING_RGB888,
+};
+
+/**
+ * struct mx3fb_platform_data - mx3fb platform data
+ *
+ * @dma_dev: pointer to the dma-device, used for dma-slave connection
+ * @mode: pointer to a platform-provided per mxc_register_fb() videomode
+ */
+struct mx3fb_platform_data {
+ struct device *dma_dev;
+ const char *name;
+ const struct fb_videomode *mode;
+ int num_modes;
+ enum disp_data_mapping disp_data_fmt;
+};
+
+#endif
--- /dev/null
+/* linux/include/asm/arch-nuc900/fb.h
+ *
+ * Copyright (c) 2008 Nuvoton technology corporation
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Changelog:
+ *
+ * 2008/08/26 vincen.zswan modify this file for LCD.
+ */
+
+#ifndef __ASM_ARM_FB_H
+#define __ASM_ARM_FB_H
+
+
+
+/* LCD Controller Hardware Desc */
+struct nuc900fb_hw {
+ unsigned int lcd_dccs;
+ unsigned int lcd_device_ctrl;
+ unsigned int lcd_mpulcd_cmd;
+ unsigned int lcd_int_cs;
+ unsigned int lcd_crtc_size;
+ unsigned int lcd_crtc_dend;
+ unsigned int lcd_crtc_hr;
+ unsigned int lcd_crtc_hsync;
+ unsigned int lcd_crtc_vr;
+ unsigned int lcd_va_baddr0;
+ unsigned int lcd_va_baddr1;
+ unsigned int lcd_va_fbctrl;
+ unsigned int lcd_va_scale;
+ unsigned int lcd_va_test;
+ unsigned int lcd_va_win;
+ unsigned int lcd_va_stuff;
+};
+
+/* LCD Display Description */
+struct nuc900fb_display {
+ /* LCD Image type */
+ unsigned type;
+
+ /* LCD Screen Size */
+ unsigned short width;
+ unsigned short height;
+
+ /* LCD Screen Info */
+ unsigned short xres;
+ unsigned short yres;
+ unsigned short bpp;
+
+ unsigned long pixclock;
+ unsigned short left_margin;
+ unsigned short right_margin;
+ unsigned short hsync_len;
+ unsigned short upper_margin;
+ unsigned short lower_margin;
+ unsigned short vsync_len;
+
+ /* hardware special register value */
+ unsigned int dccs;
+ unsigned int devctl;
+ unsigned int fbctrl;
+ unsigned int scale;
+};
+
+struct nuc900fb_mach_info {
+ struct nuc900fb_display *displays;
+ unsigned num_displays;
+ unsigned default_display;
+ /* GPIO Setting Info */
+ unsigned gpio_dir;
+ unsigned gpio_dir_mask;
+ unsigned gpio_data;
+ unsigned gpio_data_mask;
+};
+
+extern void __init nuc900_fb_set_platdata(struct nuc900fb_mach_info *);
+
+#endif /* __ASM_ARM_FB_H */
--- /dev/null
+/*
+ * arch/arm/mach-pxa/include/mach/pxafb.h
+ *
+ * Support for the xscale frame buffer.
+ *
+ * Author: Jean-Frederic Clere
+ * Created: Sep 22, 2003
+ * Copyright: jfclere@sinix.net
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/fb.h>
+#include <mach/regs-lcd.h>
+
+/*
+ * Supported LCD connections
+ *
+ * bits 0 - 3: for LCD panel type:
+ *
+ * STN - for passive matrix
+ * DSTN - for dual scan passive matrix
+ * TFT - for active matrix
+ *
+ * bits 4 - 9 : for bus width
+ * bits 10-17 : for AC Bias Pin Frequency
+ * bit 18 : for output enable polarity
+ * bit 19 : for pixel clock edge
+ * bit 20 : for output pixel format when base is RGBT16
+ */
+#define LCD_CONN_TYPE(_x) ((_x) & 0x0f)
+#define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f)
+
+#define LCD_TYPE_MASK 0xf
+#define LCD_TYPE_UNKNOWN 0
+#define LCD_TYPE_MONO_STN 1
+#define LCD_TYPE_MONO_DSTN 2
+#define LCD_TYPE_COLOR_STN 3
+#define LCD_TYPE_COLOR_DSTN 4
+#define LCD_TYPE_COLOR_TFT 5
+#define LCD_TYPE_SMART_PANEL 6
+#define LCD_TYPE_MAX 7
+
+#define LCD_MONO_STN_4BPP ((4 << 4) | LCD_TYPE_MONO_STN)
+#define LCD_MONO_STN_8BPP ((8 << 4) | LCD_TYPE_MONO_STN)
+#define LCD_MONO_DSTN_8BPP ((8 << 4) | LCD_TYPE_MONO_DSTN)
+#define LCD_COLOR_STN_8BPP ((8 << 4) | LCD_TYPE_COLOR_STN)
+#define LCD_COLOR_DSTN_16BPP ((16 << 4) | LCD_TYPE_COLOR_DSTN)
+#define LCD_COLOR_TFT_8BPP ((8 << 4) | LCD_TYPE_COLOR_TFT)
+#define LCD_COLOR_TFT_16BPP ((16 << 4) | LCD_TYPE_COLOR_TFT)
+#define LCD_COLOR_TFT_18BPP ((18 << 4) | LCD_TYPE_COLOR_TFT)
+#define LCD_SMART_PANEL_8BPP ((8 << 4) | LCD_TYPE_SMART_PANEL)
+#define LCD_SMART_PANEL_16BPP ((16 << 4) | LCD_TYPE_SMART_PANEL)
+#define LCD_SMART_PANEL_18BPP ((18 << 4) | LCD_TYPE_SMART_PANEL)
+
+#define LCD_AC_BIAS_FREQ(x) (((x) & 0xff) << 10)
+#define LCD_BIAS_ACTIVE_HIGH (0 << 18)
+#define LCD_BIAS_ACTIVE_LOW (1 << 18)
+#define LCD_PCLK_EDGE_RISE (0 << 19)
+#define LCD_PCLK_EDGE_FALL (1 << 19)
+#define LCD_ALTERNATE_MAPPING (1 << 20)
+
+/*
+ * This structure describes the machine which we are running on.
+ * It is set in linux/arch/arm/mach-pxa/machine_name.c and used in the probe routine
+ * of linux/drivers/video/pxafb.c
+ */
+struct pxafb_mode_info {
+ u_long pixclock;
+
+ u_short xres;
+ u_short yres;
+
+ u_char bpp;
+ u_int cmap_greyscale:1,
+ depth:8,
+ transparency:1,
+ unused:22;
+
+ /* Parallel Mode Timing */
+ u_char hsync_len;
+ u_char left_margin;
+ u_char right_margin;
+
+ u_char vsync_len;
+ u_char upper_margin;
+ u_char lower_margin;
+ u_char sync;
+
+ /* Smart Panel Mode Timing - see PXA27x DM 7.4.15.0.3 for details
+ * Note:
+ * 1. all parameters in nanosecond (ns)
+ * 2. a0cs{rd,wr}_set_hld are controlled by the same register bits
+ * in pxa27x and pxa3xx, initialize them to the same value or
+ * the larger one will be used
+ * 3. same to {rd,wr}_pulse_width
+ *
+ * 4. LCD_PCLK_EDGE_{RISE,FALL} controls the L_PCLK_WR polarity
+ * 5. sync & FB_SYNC_HOR_HIGH_ACT controls the L_LCLK_A0
+ * 6. sync & FB_SYNC_VERT_HIGH_ACT controls the L_LCLK_RD
+ */
+ unsigned a0csrd_set_hld; /* A0 and CS Setup/Hold Time before/after L_FCLK_RD */
+ unsigned a0cswr_set_hld; /* A0 and CS Setup/Hold Time before/after L_PCLK_WR */
+ unsigned wr_pulse_width; /* L_PCLK_WR pulse width */
+ unsigned rd_pulse_width; /* L_FCLK_RD pulse width */
+ unsigned cmd_inh_time; /* Command Inhibit time between two writes */
+ unsigned op_hold_time; /* Output Hold time from L_FCLK_RD negation */
+};
+
+struct pxafb_mach_info {
+ struct pxafb_mode_info *modes;
+ unsigned int num_modes;
+
+ unsigned int lcd_conn;
+ unsigned long video_mem_size;
+
+ u_int fixed_modes:1,
+ cmap_inverse:1,
+ cmap_static:1,
+ acceleration_enabled:1,
+ unused:28;
+
+ /* The following should be defined in LCCR0
+ * LCCR0_Act or LCCR0_Pas Active or Passive
+ * LCCR0_Sngl or LCCR0_Dual Single/Dual panel
+ * LCCR0_Mono or LCCR0_Color Mono/Color
+ * LCCR0_4PixMono or LCCR0_8PixMono (in mono single mode)
+ * LCCR0_DMADel(Tcpu) (optional) DMA request delay
+ *
+ * The following should not be defined in LCCR0:
+ * LCCR0_OUM, LCCR0_BM, LCCR0_QDM, LCCR0_DIS, LCCR0_EFM
+ * LCCR0_IUM, LCCR0_SFM, LCCR0_LDM, LCCR0_ENB
+ */
+ u_int lccr0;
+ /* The following should be defined in LCCR3
+ * LCCR3_OutEnH or LCCR3_OutEnL Output enable polarity
+ * LCCR3_PixRsEdg or LCCR3_PixFlEdg Pixel clock edge type
+ * LCCR3_Acb(X) AB Bias pin frequency
+ * LCCR3_DPC (optional) Double Pixel Clock mode (untested)
+ *
+ * The following should not be defined in LCCR3
+ * LCCR3_HSP, LCCR3_VSP, LCCR0_Pcd(x), LCCR3_Bpp
+ */
+ u_int lccr3;
+ /* The following should be defined in LCCR4
+ * LCCR4_PAL_FOR_0 or LCCR4_PAL_FOR_1 or LCCR4_PAL_FOR_2
+ *
+ * All other bits in LCCR4 should be left alone.
+ */
+ u_int lccr4;
+ void (*pxafb_backlight_power)(int);
+ void (*pxafb_lcd_power)(int, struct fb_var_screeninfo *);
+ void (*smart_update)(struct fb_info *);
+};
+
+void pxa_set_fb_info(struct device *, struct pxafb_mach_info *);
+unsigned long pxafb_get_hsync_time(struct device *dev);
+
+#ifdef CONFIG_FB_PXA_SMARTPANEL
+extern int pxafb_smart_queue(struct fb_info *info, uint16_t *cmds, int);
+extern int pxafb_smart_flush(struct fb_info *info);
+#else
+static inline int pxafb_smart_queue(struct fb_info *info,
+ uint16_t *cmds, int n)
+{
+ return 0;
+}
+
+static inline int pxafb_smart_flush(struct fb_info *info)
+{
+ return 0;
+}
+#endif
--- /dev/null
+/*
+ * VT8500/WM8505 Frame Buffer platform data definitions
+ *
+ * Copyright (C) 2010 Ed Spiridonov <edo.rus@gmail.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _VT8500FB_H
+#define _VT8500FB_H
+
+#include <linux/fb.h>
+
+struct vt8500fb_platform_data {
+ struct fb_videomode mode;
+ u32 xres_virtual;
+ u32 yres_virtual;
+ u32 bpp;
+ unsigned long video_mem_phys;
+ void *video_mem_virt;
+ unsigned long video_mem_len;
+};
+
+#endif /* _VT8500FB_H */
#include <sound/ac97_codec.h>
#include <sound/soc.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-ep93xx.h>
#include "ep93xx-pcm.h"
/*
#include <mach/hardware.h>
#include <mach/ep93xx-regs.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-ep93xx.h>
#include "ep93xx-pcm.h"
#include <sound/soc.h>
#include <sound/dmaengine_pcm.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-ep93xx.h>
#include <mach/hardware.h>
#include <mach/ep93xx-regs.h>
#include <sound/soc.h>
#include <sound/dmaengine_pcm.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-imx.h>
#include "imx-pcm.h"
#include <asm/fiq.h>
#include <mach/irqs.h>
-#include <mach/ssi.h>
+#include <linux/platform_data/asoc-imx-ssi.h>
#include "imx-ssi.h"
#include <sound/pcm_params.h>
#include <sound/soc.h>
-#include <mach/ssi.h>
+#include <linux/platform_data/asoc-imx-ssi.h>
#include <mach/hardware.h>
#include "imx-ssi.h"
#define DRV_NAME "imx-ssi"
#include <linux/dmaengine.h>
-#include <mach/dma.h>
+#include <linux/platform_data/dma-imx.h>
#include "imx-pcm.h"
struct imx_ssi {
#include <sound/pcm.h>
#include <sound/pcm_params.h>
#include <sound/soc.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-kirkwood.h>
#include "kirkwood.h"
#define DRV_NAME "kirkwood-i2s"
#include <linux/slab.h>
#include <sound/soc.h>
#include <mach/kirkwood.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-kirkwood.h>
#include <asm/mach-types.h>
#include "../codecs/cs42l51.h"
#include <linux/slab.h>
#include <sound/soc.h>
#include <mach/kirkwood.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-kirkwood.h>
#include <asm/mach-types.h>
#include "../codecs/alc5623.h"
#include <asm/mach-types.h>
#include <mach/audio.h>
-#include <mach/palmasoc.h>
+#include <linux/platform_data/asoc-palm27x.h>
#include "../codecs/wm9712.h"
#include "pxa2xx-ac97.h"
#include <mach/dma.h>
#include <plat/regs-ac97.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-s3c.h>
#include "dma.h"
#include <sound/soc.h>
#include <sound/pcm_params.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-s3c.h>
#include "dma.h"
#include "idma.h"
#include <sound/soc.h>
#include <sound/pcm_params.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-s3c.h>
#include <mach/dma.h>
#include "dma.h"
#include <sound/soc.h>
-#include <plat/audio-simtec.h>
+#include <linux/platform_data/asoc-s3c24xx_simtec.h>
#include "s3c24xx-i2s.h"
#include "s3c24xx_simtec.h"
#include <sound/soc.h>
#include <sound/pcm_params.h>
-#include <plat/audio.h>
+#include <linux/platform_data/asoc-s3c.h>
#include <mach/dma.h>
#include "dma.h"
projects / firefly-linux-kernel-4.4.55.git / commitdiff