--- /dev/null
+* Insignal's Exynos4210 based Origen evaluation board
+
+Origen low-cost evaluation board is based on Samsung's Exynos4210 SoC.
+
+Required root node properties:
+ - compatible = should be one or more of the following.
+ (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.
+ (b) "samsung,exynos4210" - for boards based on Exynos4210 SoC.
--- /dev/null
+* Samsung's Exynos4210 based SMDKV310 evaluation board
+
+SMDKV310 evaluation board is based on Samsung's Exynos4210 SoC.
+
+Required root node properties:
+ - compatible = should be one or more of the following.
+ (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.
+ (b) "samsung,exynos4210" - for boards based on Exynos4210 SoC.
--- /dev/null
+* ARM PrimeCell PL330 DMA Controller
+
+The ARM PrimeCell PL330 DMA controller can move blocks of memory contents
+between memory and peripherals or memory to memory.
+
+Required properties:
+ - compatible: should include both "arm,pl330" and "arm,primecell".
+ - reg: physical base address of the controller and length of memory mapped
+ region.
+ - interrupts: interrupt number to the cpu.
+
+Example:
+
+ pdma0: pdma@12680000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x12680000 0x1000>;
+ interrupts = <99>;
+ };
+
+Client drivers (device nodes requiring dma transfers from dev-to-mem or
+mem-to-dev) should specify the DMA channel numbers using a two-value pair
+as shown below.
+
+ [property name] = <[phandle of the dma controller] [dma request id]>;
+
+ where 'dma request id' is the dma request number which is connected
+ to the client controller. The 'property name' is recommended to be
+ of the form <name>-dma-channel.
+
+ Example: tx-dma-channel = <&pdma0 12>;
--- /dev/null
+Samsung Exynos4 GPIO Controller
+
+Required properties:
+- compatible: Compatible property value should be "samsung,exynos4-gpio>".
+
+- reg: Physical base address of the controller and length of memory mapped
+ region.
+
+- #gpio-cells: Should be 4. The syntax of the gpio specifier used by client nodes
+ should be the following with values derived from the SoC user manual.
+ <[phandle of the gpio controller node]
+ [pin number within the gpio controller]
+ [mux function]
+ [pull up/down]
+ [drive strength]>
+
+ Values for gpio specifier:
+ - Pin number: is a value between 0 to 7.
+ - Pull Up/Down: 0 - Pull Up/Down Disabled.
+ 1 - Pull Down Enabled.
+ 3 - Pull Up Enabled.
+ - Drive Strength: 0 - 1x,
+ 1 - 3x,
+ 2 - 2x,
+ 3 - 4x
+
+- gpio-controller: Specifies that the node is a gpio controller.
+- #address-cells: should be 1.
+- #size-cells: should be 1.
+
+Example:
+
+ gpa0: gpio-controller@11400000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400000 0x20>;
+ #gpio-cells = <4>;
+ gpio-controller;
+ };
--- /dev/null
+* Samsung's Keypad Controller device tree bindings
+
+Samsung's Keypad controller is used to interface a SoC with a matrix-type
+keypad device. The keypad controller supports multiple row and column lines.
+A key can be placed at each intersection of a unique row and a unique column.
+The keypad controller can sense a key-press and key-release and report the
+event using a interrupt to the cpu.
+
+Required SoC Specific Properties:
+- compatible: should be one of the following
+ - "samsung,s3c6410-keypad": For controllers compatible with s3c6410 keypad
+ controller.
+ - "samsung,s5pv210-keypad": For controllers compatible with s5pv210 keypad
+ controller.
+
+- reg: physical base address of the controller and length of memory mapped
+ region.
+
+- interrupts: The interrupt number to the cpu.
+
+Required Board Specific Properties:
+- samsung,keypad-num-rows: Number of row lines connected to the keypad
+ controller.
+
+- samsung,keypad-num-columns: Number of column lines connected to the
+ keypad controller.
+
+- row-gpios: List of gpios used as row lines. The gpio specifier for
+ this property depends on the gpio controller to which these row lines
+ are connected.
+
+- col-gpios: List of gpios used as column lines. The gpio specifier for
+ this property depends on the gpio controller to which these column
+ lines are connected.
+
+- Keys represented as child nodes: Each key connected to the keypad
+ controller is represented as a child node to the keypad controller
+ device node and should include the following properties.
+ - keypad,row: the row number to which the key is connected.
+ - keypad,column: the column number to which the key is connected.
+ - linux,code: the key-code to be reported when the key is pressed
+ and released.
+
+Optional Properties specific to linux:
+- linux,keypad-no-autorepeat: do no enable autorepeat feature.
+- linux,keypad-wakeup: use any event on keypad as wakeup event.
+
+
+Example:
+ keypad@100A0000 {
+ compatible = "samsung,s5pv210-keypad";
+ reg = <0x100A0000 0x100>;
+ interrupts = <173>;
+ samsung,keypad-num-rows = <2>;
+ samsung,keypad-num-columns = <8>;
+ linux,input-no-autorepeat;
+ linux,input-wakeup;
+
+ row-gpios = <&gpx2 0 3 3 0
+ &gpx2 1 3 3 0>;
+
+ col-gpios = <&gpx1 0 3 0 0
+ &gpx1 1 3 0 0
+ &gpx1 2 3 0 0
+ &gpx1 3 3 0 0
+ &gpx1 4 3 0 0
+ &gpx1 5 3 0 0
+ &gpx1 6 3 0 0
+ &gpx1 7 3 0 0>;
+
+ key_1 {
+ keypad,row = <0>;
+ keypad,column = <3>;
+ linux,code = <2>;
+ };
+
+ key_2 {
+ keypad,row = <0>;
+ keypad,column = <4>;
+ linux,code = <3>;
+ };
+
+ key_3 {
+ keypad,row = <0>;
+ keypad,column = <5>;
+ linux,code = <4>;
+ };
+ };
--- /dev/null
+* Samsung's S3C Real Time Clock controller
+
+Required properties:
+- compatible: should be one of the following.
+ * "samsung,s3c2410-rtc" - for controllers compatible with s3c2410 rtc.
+ * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc.
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- interrupts: Two interrupt numbers to the cpu should be specified. First
+ interrupt number is the rtc alarm interupt and second interrupt number
+ is the rtc tick interrupt. The number of cells representing a interrupt
+ depends on the parent interrupt controller.
+
+Example:
+
+ rtc@10070000 {
+ compatible = "samsung,s3c6410-rtc";
+ reg = <0x10070000 0x100>;
+ interrupts = <44 0 45 0>;
+ };
--- /dev/null
+* Samsung's UART Controller
+
+The Samsung's UART controller is used for interfacing SoC with serial communicaion
+devices.
+
+Required properties:
+- compatible: should be
+ - "samsung,exynos4210-uart", for UART's compatible with Exynos4210 uart ports.
+
+- reg: base physical address of the controller and length of memory mapped
+ region.
+
+- interrupts: interrupt number to the cpu. The interrupt specifier format depends
+ on the interrupt controller parent.
--- /dev/null
+/*
+ * Samsung's Exynos4210 based Origen board device tree source
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ * www.linaro.org
+ *
+ * Device tree source file for Insignal's Origen board which is based on
+ * Samsung's Exynos4210 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos4210.dtsi"
+
+/ {
+ model = "Insignal Origen evaluation board based on Exynos4210";
+ compatible = "insignal,origen", "samsung,exynos4210";
+
+ memory {
+ reg = <0x40000000 0x40000000>;
+ };
+
+ chosen {
+ bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC2,115200 init=/linuxrc";
+ };
+
+ sdhci@12530000 {
+ samsung,sdhci-bus-width = <4>;
+ linux,mmc_cap_4_bit_data;
+ samsung,sdhci-cd-internal;
+ gpio-cd = <&gpk2 2 2 3 3>;
+ gpios = <&gpk2 0 2 0 3>,
+ <&gpk2 1 2 0 3>,
+ <&gpk2 3 2 3 3>,
+ <&gpk2 4 2 3 3>,
+ <&gpk2 5 2 3 3>,
+ <&gpk2 6 2 3 3>;
+ };
+
+ sdhci@12510000 {
+ samsung,sdhci-bus-width = <4>;
+ linux,mmc_cap_4_bit_data;
+ samsung,sdhci-cd-internal;
+ gpio-cd = <&gpk0 2 2 3 3>;
+ gpios = <&gpk0 0 2 0 3>,
+ <&gpk0 1 2 0 3>,
+ <&gpk0 3 2 3 3>,
+ <&gpk0 4 2 3 3>,
+ <&gpk0 5 2 3 3>,
+ <&gpk0 6 2 3 3>;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ up {
+ label = "Up";
+ gpios = <&gpx2 0 0 0 2>;
+ linux,code = <103>;
+ };
+
+ down {
+ label = "Down";
+ gpios = <&gpx2 1 0 0 2>;
+ linux,code = <108>;
+ };
+
+ back {
+ label = "Back";
+ gpios = <&gpx1 7 0 0 2>;
+ linux,code = <158>;
+ };
+
+ home {
+ label = "Home";
+ gpios = <&gpx1 6 0 0 2>;
+ linux,code = <102>;
+ };
+
+ menu {
+ label = "Menu";
+ gpios = <&gpx1 5 0 0 2>;
+ linux,code = <139>;
+ };
+ };
+
+ keypad@100A0000 {
+ status = "disabled";
+ };
+
+ sdhci@12520000 {
+ status = "disabled";
+ };
+
+ sdhci@12540000 {
+ status = "disabled";
+ };
+
+ i2c@13860000 {
+ status = "disabled";
+ };
+
+ i2c@13870000 {
+ status = "disabled";
+ };
+
+ i2c@13880000 {
+ status = "disabled";
+ };
+
+ i2c@13890000 {
+ status = "disabled";
+ };
+
+ i2c@138A0000 {
+ status = "disabled";
+ };
+
+ i2c@138B0000 {
+ status = "disabled";
+ };
+
+ i2c@138C0000 {
+ status = "disabled";
+ };
+
+ i2c@138D0000 {
+ status = "disabled";
+ };
+};
--- /dev/null
+/*
+ * Samsung's Exynos4210 based SMDKV310 board device tree source
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ * www.linaro.org
+ *
+ * Device tree source file for Samsung's SMDKV310 board which is based on
+ * Samsung's Exynos4210 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos4210.dtsi"
+
+/ {
+ model = "Samsung smdkv310 evaluation board based on Exynos4210";
+ compatible = "samsung,smdkv310", "samsung,exynos4210";
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ chosen {
+ bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc";
+ };
+
+ sdhci@12530000 {
+ samsung,sdhci-bus-width = <4>;
+ linux,mmc_cap_4_bit_data;
+ samsung,sdhci-cd-internal;
+ gpio-cd = <&gpk2 2 2 3 3>;
+ gpios = <&gpk2 0 2 0 3>,
+ <&gpk2 1 2 0 3>,
+ <&gpk2 3 2 3 3>,
+ <&gpk2 4 2 3 3>,
+ <&gpk2 5 2 3 3>,
+ <&gpk2 6 2 3 3>;
+ };
+
+ keypad@100A0000 {
+ samsung,keypad-num-rows = <2>;
+ samsung,keypad-num-columns = <8>;
+ linux,keypad-no-autorepeat;
+ linux,keypad-wakeup;
+
+ row-gpios = <&gpx2 0 3 3 0>,
+ <&gpx2 1 3 3 0>;
+
+ col-gpios = <&gpx1 0 3 0 0>,
+ <&gpx1 1 3 0 0>,
+ <&gpx1 2 3 0 0>,
+ <&gpx1 3 3 0 0>,
+ <&gpx1 4 3 0 0>,
+ <&gpx1 5 3 0 0>,
+ <&gpx1 6 3 0 0>,
+ <&gpx1 7 3 0 0>;
+
+ key_1 {
+ keypad,row = <0>;
+ keypad,column = <3>;
+ linux,code = <2>;
+ };
+
+ key_2 {
+ keypad,row = <0>;
+ keypad,column = <4>;
+ linux,code = <3>;
+ };
+
+ key_3 {
+ keypad,row = <0>;
+ keypad,column = <5>;
+ linux,code = <4>;
+ };
+
+ key_4 {
+ keypad,row = <0>;
+ keypad,column = <6>;
+ linux,code = <5>;
+ };
+
+ key_5 {
+ keypad,row = <0>;
+ keypad,column = <7>;
+ linux,code = <6>;
+ };
+
+ key_a {
+ keypad,row = <1>;
+ keypad,column = <3>;
+ linux,code = <30>;
+ };
+
+ key_b {
+ keypad,row = <1>;
+ keypad,column = <4>;
+ linux,code = <48>;
+ };
+
+ key_c {
+ keypad,row = <1>;
+ keypad,column = <5>;
+ linux,code = <46>;
+ };
+
+ key_d {
+ keypad,row = <1>;
+ keypad,column = <6>;
+ linux,code = <32>;
+ };
+
+ key_e {
+ keypad,row = <1>;
+ keypad,column = <7>;
+ linux,code = <18>;
+ };
+ };
+
+ i2c@13860000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <20000>;
+ gpios = <&gpd1 0 2 3 0>,
+ <&gpd1 1 2 3 0>;
+
+ eeprom@50 {
+ compatible = "samsung,24ad0xd1";
+ reg = <0x50>;
+ };
+
+ eeprom@52 {
+ compatible = "samsung,24ad0xd1";
+ reg = <0x52>;
+ };
+ };
+
+ sdhci@12510000 {
+ status = "disabled";
+ };
+
+ sdhci@12520000 {
+ status = "disabled";
+ };
+
+ sdhci@12540000 {
+ status = "disabled";
+ };
+
+ i2c@13870000 {
+ status = "disabled";
+ };
+
+ i2c@13880000 {
+ status = "disabled";
+ };
+
+ i2c@13890000 {
+ status = "disabled";
+ };
+
+ i2c@138A0000 {
+ status = "disabled";
+ };
+
+ i2c@138B0000 {
+ status = "disabled";
+ };
+
+ i2c@138C0000 {
+ status = "disabled";
+ };
+
+ i2c@138D0000 {
+ status = "disabled";
+ };
+};
--- /dev/null
+/*
+ * Samsung's Exynos4210 SoC device tree source
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ * www.linaro.org
+ *
+ * Samsung's Exynos4210 SoC device nodes are listed in this file. Exynos4210
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4210 SoC. As device tree coverage for Exynos4210 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "skeleton.dtsi"
+
+/ {
+ compatible = "samsung,exynos4210";
+ interrupt-parent = <&gic>;
+
+ gic:interrupt-controller@10490000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x10490000 0x1000>, <0x10480000 0x100>;
+ };
+
+ watchdog@10060000 {
+ compatible = "samsung,s3c2410-wdt";
+ reg = <0x10060000 0x100>;
+ interrupts = <0 43 0>;
+ };
+
+ rtc@10070000 {
+ compatible = "samsung,s3c6410-rtc";
+ reg = <0x10070000 0x100>;
+ interrupts = <0 44 0>, <0 45 0>;
+ };
+
+ keypad@100A0000 {
+ compatible = "samsung,s5pv210-keypad";
+ reg = <0x100A0000 0x100>;
+ interrupts = <0 109 0>;
+ };
+
+ sdhci@12510000 {
+ compatible = "samsung,exynos4210-sdhci";
+ reg = <0x12510000 0x100>;
+ interrupts = <0 73 0>;
+ };
+
+ sdhci@12520000 {
+ compatible = "samsung,exynos4210-sdhci";
+ reg = <0x12520000 0x100>;
+ interrupts = <0 74 0>;
+ };
+
+ sdhci@12530000 {
+ compatible = "samsung,exynos4210-sdhci";
+ reg = <0x12530000 0x100>;
+ interrupts = <0 75 0>;
+ };
+
+ sdhci@12540000 {
+ compatible = "samsung,exynos4210-sdhci";
+ reg = <0x12540000 0x100>;
+ interrupts = <0 76 0>;
+ };
+
+ serial@13800000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13800000 0x100>;
+ interrupts = <0 52 0>;
+ };
+
+ serial@13810000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13810000 0x100>;
+ interrupts = <0 53 0>;
+ };
+
+ serial@13820000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13820000 0x100>;
+ interrupts = <0 54 0>;
+ };
+
+ serial@13830000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13830000 0x100>;
+ interrupts = <0 55 0>;
+ };
+
+ i2c@13860000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13860000 0x100>;
+ interrupts = <0 58 0>;
+ };
+
+ i2c@13870000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13870000 0x100>;
+ interrupts = <0 59 0>;
+ };
+
+ i2c@13880000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13880000 0x100>;
+ interrupts = <0 60 0>;
+ };
+
+ i2c@13890000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13890000 0x100>;
+ interrupts = <0 61 0>;
+ };
+
+ i2c@138A0000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x138A0000 0x100>;
+ interrupts = <0 62 0>;
+ };
+
+ i2c@138B0000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x138B0000 0x100>;
+ interrupts = <0 63 0>;
+ };
+
+ i2c@138C0000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x138C0000 0x100>;
+ interrupts = <0 64 0>;
+ };
+
+ i2c@138D0000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x138D0000 0x100>;
+ interrupts = <0 65 0>;
+ };
+
+ amba {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "arm,amba-bus";
+ interrupt-parent = <&gic>;
+ ranges;
+
+ pdma0: pdma@12680000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x12680000 0x1000>;
+ interrupts = <0 35 0>;
+ };
+
+ pdma1: pdma@12690000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x12690000 0x1000>;
+ interrupts = <0 36 0>;
+ };
+ };
+
+ gpio-controllers {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ gpio-controller;
+ ranges;
+
+ gpa0: gpio-controller@11400000 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400000 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpa1: gpio-controller@11400020 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400020 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpb: gpio-controller@11400040 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400040 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpc0: gpio-controller@11400060 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400060 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpc1: gpio-controller@11400080 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400080 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpd0: gpio-controller@114000A0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x114000A0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpd1: gpio-controller@114000C0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x114000C0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpe0: gpio-controller@114000E0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x114000E0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpe1: gpio-controller@11400100 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400100 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpe2: gpio-controller@11400120 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400120 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpe3: gpio-controller@11400140 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400140 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpe4: gpio-controller@11400160 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400160 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpf0: gpio-controller@11400180 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11400180 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpf1: gpio-controller@114001A0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x114001A0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpf2: gpio-controller@114001C0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x114001C0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpf3: gpio-controller@114001E0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x114001E0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpj0: gpio-controller@11000000 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000000 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpj1: gpio-controller@11000020 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000020 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpk0: gpio-controller@11000040 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000040 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpk1: gpio-controller@11000060 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000060 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpk2: gpio-controller@11000080 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000080 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpk3: gpio-controller@110000A0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x110000A0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpl0: gpio-controller@110000C0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x110000C0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpl1: gpio-controller@110000E0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x110000E0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpl2: gpio-controller@11000100 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000100 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpy0: gpio-controller@11000120 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000120 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpy1: gpio-controller@11000140 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000140 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpy2: gpio-controller@11000160 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000160 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpy3: gpio-controller@11000180 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000180 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpy4: gpio-controller@110001A0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x110001A0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpy5: gpio-controller@110001C0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x110001C0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpy6: gpio-controller@110001E0 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x110001E0 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpx0: gpio-controller@11000C00 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000C00 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpx1: gpio-controller@11000C20 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000C20 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpx2: gpio-controller@11000C40 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000C40 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpx3: gpio-controller@11000C60 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x11000C60 0x20>;
+ #gpio-cells = <4>;
+ };
+
+ gpz: gpio-controller@03860000 {
+ compatible = "samsung,exynos4-gpio";
+ reg = <0x03860000 0x20>;
+ #gpio-cells = <4>;
+ };
+ };
+};
help
Use MCT (Multi Core Timer) as kernel timers
+config EXYNOS4_DEV_DMA
+ bool
+ help
+ Compile in amba device definitions for DMA controller
+
config EXYNOS4_DEV_AHCI
bool
help
select SAMSUNG_DEV_BACKLIGHT
select EXYNOS4_DEV_AHCI
select SAMSUNG_DEV_KEYPAD
+ select EXYNOS4_DEV_DMA
select EXYNOS4_DEV_PD
select SAMSUNG_DEV_PWM
select EXYNOS4_DEV_USB_OHCI
select S3C_DEV_HSMMC2
select S3C_DEV_HSMMC3
select EXYNOS4_DEV_AHCI
+ select EXYNOS4_DEV_DMA
select EXYNOS4_DEV_SYSMMU
select EXYNOS4_SETUP_SDHCI
help
select S5P_DEV_MFC
select S5P_DEV_ONENAND
select S5P_DEV_TV
+ select EXYNOS4_DEV_DMA
select EXYNOS4_DEV_PD
select EXYNOS4_SETUP_FIMD0
select EXYNOS4_SETUP_I2C1
select S5P_DEV_MFC
select S5P_DEV_USB_EHCI
select S5P_SETUP_MIPIPHY
+ select EXYNOS4_DEV_DMA
select EXYNOS4_DEV_PD
select EXYNOS4_SETUP_FIMC
select EXYNOS4_SETUP_FIMD0
select S5P_DEV_USB_EHCI
select SAMSUNG_DEV_BACKLIGHT
select SAMSUNG_DEV_PWM
+ select EXYNOS4_DEV_DMA
select EXYNOS4_DEV_PD
select EXYNOS4_DEV_USB_OHCI
select EXYNOS4_SETUP_FIMD0
Machine support for Samsung SMDK4412
endif
+comment "Flattened Device Tree based board for Exynos4 based SoC"
+
+config MACH_EXYNOS4_DT
+ bool "Samsung Exynos4 Machine using device tree"
+ select CPU_EXYNOS4210
+ select USE_OF
+ select ARM_AMBA
+ select HAVE_SAMSUNG_KEYPAD if INPUT_KEYBOARD
+ help
+ Machine support for Samsung Exynos4 machine with device tree enabled.
+ Select this if a fdt blob is available for the Exynos4 SoC based board.
+ Note: This is under development and not all peripherals can be supported
+ with this machine file.
+
if ARCH_EXYNOS4
comment "Configuration for HSMMC 8-bit bus width"
# Core support for EXYNOS4 system
obj-$(CONFIG_ARCH_EXYNOS4) += cpu.o init.o clock.o irq-combiner.o setup-i2c0.o
-obj-$(CONFIG_ARCH_EXYNOS4) += irq-eint.o dma.o pmu.o
+obj-$(CONFIG_ARCH_EXYNOS4) += irq-eint.o pmu.o
obj-$(CONFIG_CPU_EXYNOS4210) += clock-exynos4210.o
obj-$(CONFIG_SOC_EXYNOS4212) += clock-exynos4212.o
obj-$(CONFIG_PM) += pm.o
obj-$(CONFIG_MACH_SMDK4212) += mach-smdk4x12.o
obj-$(CONFIG_MACH_SMDK4412) += mach-smdk4x12.o
+obj-$(CONFIG_MACH_EXYNOS4_DT) += mach-exynos4-dt.o
+
# device support
obj-$(CONFIG_ARCH_EXYNOS4) += dev-audio.o
obj-$(CONFIG_EXYNOS4_DEV_PD) += dev-pd.o
obj-$(CONFIG_EXYNOS4_DEV_SYSMMU) += dev-sysmmu.o
obj-$(CONFIG_EXYNOS4_DEV_DWMCI) += dev-dwmci.o
+obj-$(CONFIG_EXYNOS4_DEV_DMA) += dma.o
obj-$(CONFIG_EXYNOS4_DEV_USB_OHCI) += dev-ohci.o
obj-$(CONFIG_EXYNOS4_SETUP_FIMC) += setup-fimc.o
obj-$(CONFIG_EXYNOS4_SETUP_I2C6) += setup-i2c6.o
obj-$(CONFIG_EXYNOS4_SETUP_I2C7) += setup-i2c7.o
obj-$(CONFIG_EXYNOS4_SETUP_KEYPAD) += setup-keypad.o
-obj-$(CONFIG_EXYNOS4_SETUP_SDHCI) += setup-sdhci.o
obj-$(CONFIG_EXYNOS4_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
obj-$(CONFIG_EXYNOS4_SETUP_USB_PHY) += setup-usb-phy.o
.devname = "s5p-sdo",
.enable = exynos4_clk_dac_ctrl,
.ctrlbit = (1 << 0),
- }, {
- .name = "dma",
- .devname = "dma-pl330.0",
- .enable = exynos4_clk_ip_fsys_ctrl,
- .ctrlbit = (1 << 0),
- }, {
- .name = "dma",
- .devname = "dma-pl330.1",
- .enable = exynos4_clk_ip_fsys_ctrl,
- .ctrlbit = (1 << 1),
}, {
.name = "adc",
.enable = exynos4_clk_ip_peril_ctrl,
}
};
+static struct clk clk_pdma0 = {
+ .name = "dma",
+ .devname = "dma-pl330.0",
+ .enable = exynos4_clk_ip_fsys_ctrl,
+ .ctrlbit = (1 << 0),
+};
+
+static struct clk clk_pdma1 = {
+ .name = "dma",
+ .devname = "dma-pl330.1",
+ .enable = exynos4_clk_ip_fsys_ctrl,
+ .ctrlbit = (1 << 1),
+};
+
struct clk *clkset_group_list[] = {
[0] = &clk_ext_xtal_mux,
[1] = &clk_xusbxti,
static struct clksrc_clk clksrcs[] = {
{
- .clk = {
- .name = "uclk1",
- .devname = "s5pv210-uart.0",
- .enable = exynos4_clksrc_mask_peril0_ctrl,
- .ctrlbit = (1 << 0),
- },
- .sources = &clkset_group,
- .reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 0, .size = 4 },
- .reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 0, .size = 4 },
- }, {
- .clk = {
- .name = "uclk1",
- .devname = "s5pv210-uart.1",
- .enable = exynos4_clksrc_mask_peril0_ctrl,
- .ctrlbit = (1 << 4),
- },
- .sources = &clkset_group,
- .reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 4, .size = 4 },
- .reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 4, .size = 4 },
- }, {
- .clk = {
- .name = "uclk1",
- .devname = "s5pv210-uart.2",
- .enable = exynos4_clksrc_mask_peril0_ctrl,
- .ctrlbit = (1 << 8),
- },
- .sources = &clkset_group,
- .reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 8, .size = 4 },
- .reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 8, .size = 4 },
- }, {
- .clk = {
- .name = "uclk1",
- .devname = "s5pv210-uart.3",
- .enable = exynos4_clksrc_mask_peril0_ctrl,
- .ctrlbit = (1 << 12),
- },
- .sources = &clkset_group,
- .reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 12, .size = 4 },
- .reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 12, .size = 4 },
- }, {
.clk = {
.name = "sclk_pwm",
.enable = exynos4_clksrc_mask_peril0_ctrl,
.sources = &clkset_mout_mfc,
.reg_src = { .reg = S5P_CLKSRC_MFC, .shift = 8, .size = 1 },
.reg_div = { .reg = S5P_CLKDIV_MFC, .shift = 0, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.0",
- .parent = &clk_dout_mmc0.clk,
- .enable = exynos4_clksrc_mask_fsys_ctrl,
- .ctrlbit = (1 << 0),
- },
- .reg_div = { .reg = S5P_CLKDIV_FSYS1, .shift = 8, .size = 8 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.1",
- .parent = &clk_dout_mmc1.clk,
- .enable = exynos4_clksrc_mask_fsys_ctrl,
- .ctrlbit = (1 << 4),
- },
- .reg_div = { .reg = S5P_CLKDIV_FSYS1, .shift = 24, .size = 8 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.2",
- .parent = &clk_dout_mmc2.clk,
- .enable = exynos4_clksrc_mask_fsys_ctrl,
- .ctrlbit = (1 << 8),
- },
- .reg_div = { .reg = S5P_CLKDIV_FSYS2, .shift = 8, .size = 8 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.3",
- .parent = &clk_dout_mmc3.clk,
- .enable = exynos4_clksrc_mask_fsys_ctrl,
- .ctrlbit = (1 << 12),
- },
- .reg_div = { .reg = S5P_CLKDIV_FSYS2, .shift = 24, .size = 8 },
}, {
.clk = {
.name = "sclk_dwmmc",
}
};
+static struct clksrc_clk clk_sclk_uart0 = {
+ .clk = {
+ .name = "uclk1",
+ .devname = "exynos4210-uart.0",
+ .enable = exynos4_clksrc_mask_peril0_ctrl,
+ .ctrlbit = (1 << 0),
+ },
+ .sources = &clkset_group,
+ .reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 0, .size = 4 },
+ .reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_uart1 = {
+ .clk = {
+ .name = "uclk1",
+ .devname = "exynos4210-uart.1",
+ .enable = exynos4_clksrc_mask_peril0_ctrl,
+ .ctrlbit = (1 << 4),
+ },
+ .sources = &clkset_group,
+ .reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 4, .size = 4 },
+ .reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 4, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_uart2 = {
+ .clk = {
+ .name = "uclk1",
+ .devname = "exynos4210-uart.2",
+ .enable = exynos4_clksrc_mask_peril0_ctrl,
+ .ctrlbit = (1 << 8),
+ },
+ .sources = &clkset_group,
+ .reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 8, .size = 4 },
+ .reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 8, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_uart3 = {
+ .clk = {
+ .name = "uclk1",
+ .devname = "exynos4210-uart.3",
+ .enable = exynos4_clksrc_mask_peril0_ctrl,
+ .ctrlbit = (1 << 12),
+ },
+ .sources = &clkset_group,
+ .reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 12, .size = 4 },
+ .reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 12, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc0 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.0",
+ .parent = &clk_dout_mmc0.clk,
+ .enable = exynos4_clksrc_mask_fsys_ctrl,
+ .ctrlbit = (1 << 0),
+ },
+ .reg_div = { .reg = S5P_CLKDIV_FSYS1, .shift = 8, .size = 8 },
+};
+
+static struct clksrc_clk clk_sclk_mmc1 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.1",
+ .parent = &clk_dout_mmc1.clk,
+ .enable = exynos4_clksrc_mask_fsys_ctrl,
+ .ctrlbit = (1 << 4),
+ },
+ .reg_div = { .reg = S5P_CLKDIV_FSYS1, .shift = 24, .size = 8 },
+};
+
+static struct clksrc_clk clk_sclk_mmc2 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.2",
+ .parent = &clk_dout_mmc2.clk,
+ .enable = exynos4_clksrc_mask_fsys_ctrl,
+ .ctrlbit = (1 << 8),
+ },
+ .reg_div = { .reg = S5P_CLKDIV_FSYS2, .shift = 8, .size = 8 },
+};
+
+static struct clksrc_clk clk_sclk_mmc3 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.3",
+ .parent = &clk_dout_mmc3.clk,
+ .enable = exynos4_clksrc_mask_fsys_ctrl,
+ .ctrlbit = (1 << 12),
+ },
+ .reg_div = { .reg = S5P_CLKDIV_FSYS2, .shift = 24, .size = 8 },
+};
+
/* Clock initialization code */
static struct clksrc_clk *sysclks[] = {
&clk_mout_apll,
&clk_mout_mfc1,
};
+static struct clk *clk_cdev[] = {
+ &clk_pdma0,
+ &clk_pdma1,
+};
+
+static struct clksrc_clk *clksrc_cdev[] = {
+ &clk_sclk_uart0,
+ &clk_sclk_uart1,
+ &clk_sclk_uart2,
+ &clk_sclk_uart3,
+ &clk_sclk_mmc0,
+ &clk_sclk_mmc1,
+ &clk_sclk_mmc2,
+ &clk_sclk_mmc3,
+};
+
+static struct clk_lookup exynos4_clk_lookup[] = {
+ CLKDEV_INIT("exynos4210-uart.0", "clk_uart_baud0", &clk_sclk_uart0.clk),
+ CLKDEV_INIT("exynos4210-uart.1", "clk_uart_baud0", &clk_sclk_uart1.clk),
+ CLKDEV_INIT("exynos4210-uart.2", "clk_uart_baud0", &clk_sclk_uart2.clk),
+ CLKDEV_INIT("exynos4210-uart.3", "clk_uart_baud0", &clk_sclk_uart3.clk),
+ CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
+ CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
+ CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
+ CLKDEV_INIT("s3c-sdhci.3", "mmc_busclk.2", &clk_sclk_mmc3.clk),
+ CLKDEV_INIT("dma-pl330.0", "apb_pclk", &clk_pdma0),
+ CLKDEV_INIT("dma-pl330.1", "apb_pclk", &clk_pdma1),
+};
+
static int xtal_rate;
static unsigned long exynos4_fout_apll_get_rate(struct clk *clk)
for (ptr = 0; ptr < ARRAY_SIZE(sclk_tv); ptr++)
s3c_register_clksrc(sclk_tv[ptr], 1);
+ for (ptr = 0; ptr < ARRAY_SIZE(clksrc_cdev); ptr++)
+ s3c_register_clksrc(clksrc_cdev[ptr], 1);
+
s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
+ s3c24xx_register_clocks(clk_cdev, ARRAY_SIZE(clk_cdev));
+ for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++)
+ s3c_disable_clocks(clk_cdev[ptr], 1);
+
s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+ clkdev_add_table(exynos4_clk_lookup, ARRAY_SIZE(exynos4_clk_lookup));
register_syscore_ops(&exynos4_clock_syscore_ops);
s3c24xx_register_clock(&dummy_apb_pclk);
#include <linux/sched.h>
#include <linux/sysdev.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
(gic_bank_offset * smp_processor_id());
}
+#ifdef CONFIG_OF
+static const struct of_device_id exynos4_dt_irq_match[] = {
+ { .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
+ {},
+};
+#endif
+
void __init exynos4_init_irq(void)
{
int irq;
gic_bank_offset = soc_is_exynos4412() ? 0x4000 : 0x8000;
- gic_init(0, IRQ_PPI(0), S5P_VA_GIC_DIST, S5P_VA_GIC_CPU);
+ if (!of_have_populated_dt())
+ gic_init(0, IRQ_PPI(0), S5P_VA_GIC_DIST, S5P_VA_GIC_CPU);
+#ifdef CONFIG_OF
+ else
+ of_irq_init(exynos4_dt_irq_match);
+#endif
+
gic_arch_extn.irq_eoi = exynos4_gic_irq_fix_base;
gic_arch_extn.irq_unmask = exynos4_gic_irq_fix_base;
gic_arch_extn.irq_mask = exynos4_gic_irq_fix_base;
#include <linux/dma-mapping.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl330.h>
+#include <linux/of.h>
#include <asm/irq.h>
#include <plat/devs.h>
static u64 dma_dmamask = DMA_BIT_MASK(32);
-struct dma_pl330_peri pdma0_peri[28] = {
- {
- .peri_id = (u8)DMACH_PCM0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ0,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ2,
- }, {
- .peri_id = (u8)DMACH_SPI0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0S_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART4_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART4_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS4_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS4_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_AC97_MICIN,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_AC97_PCMIN,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_AC97_PCMOUT,
- .rqtype = MEMTODEV,
- },
+u8 pdma0_peri[] = {
+ DMACH_PCM0_RX,
+ DMACH_PCM0_TX,
+ DMACH_PCM2_RX,
+ DMACH_PCM2_TX,
+ DMACH_MSM_REQ0,
+ DMACH_MSM_REQ2,
+ DMACH_SPI0_RX,
+ DMACH_SPI0_TX,
+ DMACH_SPI2_RX,
+ DMACH_SPI2_TX,
+ DMACH_I2S0S_TX,
+ DMACH_I2S0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S2_RX,
+ DMACH_I2S2_TX,
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART2_RX,
+ DMACH_UART2_TX,
+ DMACH_UART4_RX,
+ DMACH_UART4_TX,
+ DMACH_SLIMBUS0_RX,
+ DMACH_SLIMBUS0_TX,
+ DMACH_SLIMBUS2_RX,
+ DMACH_SLIMBUS2_TX,
+ DMACH_SLIMBUS4_RX,
+ DMACH_SLIMBUS4_TX,
+ DMACH_AC97_MICIN,
+ DMACH_AC97_PCMIN,
+ DMACH_AC97_PCMOUT,
};
struct dma_pl330_platdata exynos4_pdma0_pdata = {
.nr_valid_peri = ARRAY_SIZE(pdma0_peri),
- .peri = pdma0_peri,
+ .peri_id = pdma0_peri,
};
struct amba_device exynos4_device_pdma0 = {
.periphid = 0x00041330,
};
-struct dma_pl330_peri pdma1_peri[25] = {
- {
- .peri_id = (u8)DMACH_PCM0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ1,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ3,
- }, {
- .peri_id = (u8)DMACH_SPI1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0S_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART3_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART3_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS3_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS3_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS5_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SLIMBUS5_TX,
- .rqtype = MEMTODEV,
- },
+u8 pdma1_peri[] = {
+ DMACH_PCM0_RX,
+ DMACH_PCM0_TX,
+ DMACH_PCM1_RX,
+ DMACH_PCM1_TX,
+ DMACH_MSM_REQ1,
+ DMACH_MSM_REQ3,
+ DMACH_SPI1_RX,
+ DMACH_SPI1_TX,
+ DMACH_I2S0S_TX,
+ DMACH_I2S0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S1_RX,
+ DMACH_I2S1_TX,
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART1_RX,
+ DMACH_UART1_TX,
+ DMACH_UART3_RX,
+ DMACH_UART3_TX,
+ DMACH_SLIMBUS1_RX,
+ DMACH_SLIMBUS1_TX,
+ DMACH_SLIMBUS3_RX,
+ DMACH_SLIMBUS3_TX,
+ DMACH_SLIMBUS5_RX,
+ DMACH_SLIMBUS5_TX,
};
struct dma_pl330_platdata exynos4_pdma1_pdata = {
.nr_valid_peri = ARRAY_SIZE(pdma1_peri),
- .peri = pdma1_peri,
+ .peri_id = pdma1_peri,
};
struct amba_device exynos4_device_pdma1 = {
static int __init exynos4_dma_init(void)
{
+ if (of_have_populated_dt())
+ return 0;
+
+ dma_cap_set(DMA_SLAVE, exynos4_pdma0_pdata.cap_mask);
+ dma_cap_set(DMA_CYCLIC, exynos4_pdma0_pdata.cap_mask);
amba_device_register(&exynos4_device_pdma0, &iomem_resource);
+
+ dma_cap_set(DMA_SLAVE, exynos4_pdma1_pdata.cap_mask);
+ dma_cap_set(DMA_CYCLIC, exynos4_pdma1_pdata.cap_mask);
amba_device_register(&exynos4_device_pdma1, &iomem_resource);
return 0;
cmpcc \irqnr, \irqnr
cmpne \irqnr, \tmp
cmpcs \irqnr, \irqnr
- addne \irqnr, \irqnr, #32
.endm
/* PPI: Private Peripheral Interrupt */
-#define IRQ_PPI(x) S5P_IRQ(x+16)
+#define IRQ_PPI(x) (x+16)
#define IRQ_MCT_LOCALTIMER IRQ_PPI(12)
/* SPI: Shared Peripheral Interrupt */
-#define IRQ_SPI(x) S5P_IRQ(x+32)
+#define IRQ_SPI(x) (x+32)
#define IRQ_EINT0 IRQ_SPI(16)
#define IRQ_EINT1 IRQ_SPI(17)
#define IRQ_GPIO2_NR_GROUPS 9
#define IRQ_GPIO_END (S5P_GPIOINT_BASE + S5P_GPIOINT_COUNT)
+#define IRQ_TIMER_BASE (IRQ_GPIO_END + 64)
+
/* Set the default NR_IRQS */
-#define NR_IRQS (IRQ_GPIO_END + 64)
+#define NR_IRQS (IRQ_TIMER_BASE + IRQ_TIMER_COUNT)
#endif /* __ASM_ARCH_IRQS_H */
#include <plat/devs.h>
#include <plat/regs-serial.h>
-static struct s3c24xx_uart_clksrc exynos4_serial_clocks[] = {
- [0] = {
- .name = "uclk1",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- },
-};
-
/* uart registration process */
void __init exynos4_common_init_uarts(struct s3c2410_uartcfg *cfg, int no)
{
struct s3c2410_uartcfg *tcfg = cfg;
u32 ucnt;
- for (ucnt = 0; ucnt < no; ucnt++, tcfg++) {
- if (!tcfg->clocks) {
- tcfg->has_fracval = 1;
- tcfg->clocks = exynos4_serial_clocks;
- tcfg->clocks_size = ARRAY_SIZE(exynos4_serial_clocks);
- }
- tcfg->flags |= NO_NEED_CHECK_CLKSRC;
- }
+ for (ucnt = 0; ucnt < no; ucnt++, tcfg++)
+ tcfg->has_fracval = 1;
- s3c24xx_init_uartdevs("s5pv210-uart", s5p_uart_resources, cfg, no);
+ s3c24xx_init_uartdevs("exynos4210-uart", s5p_uart_resources, cfg, no);
}
--- /dev/null
+/*
+ * Samsung's Exynos4210 flattened device tree enabled machine
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ * www.linaro.org
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/of_platform.h>
+#include <linux/serial_core.h>
+
+#include <asm/mach/arch.h>
+#include <mach/map.h>
+
+#include <plat/cpu.h>
+#include <plat/regs-serial.h>
+#include <plat/exynos4.h>
+
+/*
+ * The following lookup table is used to override device names when devices
+ * are registered from device tree. This is temporarily added to enable
+ * device tree support addition for the Exynos4 architecture.
+ *
+ * For drivers that require platform data to be provided from the machine
+ * file, a platform data pointer can also be supplied along with the
+ * devices names. Usually, the platform data elements that cannot be parsed
+ * from the device tree by the drivers (example: function pointers) are
+ * supplied. But it should be noted that this is a temporary mechanism and
+ * at some point, the drivers should be capable of parsing all the platform
+ * data from the device tree.
+ */
+static const struct of_dev_auxdata exynos4210_auxdata_lookup[] __initconst = {
+ OF_DEV_AUXDATA("samsung,exynos4210-uart", S5P_PA_UART0,
+ "exynos4210-uart.0", NULL),
+ OF_DEV_AUXDATA("samsung,exynos4210-uart", S5P_PA_UART1,
+ "exynos4210-uart.1", NULL),
+ OF_DEV_AUXDATA("samsung,exynos4210-uart", S5P_PA_UART2,
+ "exynos4210-uart.2", NULL),
+ OF_DEV_AUXDATA("samsung,exynos4210-uart", S5P_PA_UART3,
+ "exynos4210-uart.3", NULL),
+ OF_DEV_AUXDATA("samsung,exynos4210-sdhci", EXYNOS4_PA_HSMMC(0),
+ "exynos4-sdhci.0", NULL),
+ OF_DEV_AUXDATA("samsung,exynos4210-sdhci", EXYNOS4_PA_HSMMC(1),
+ "exynos4-sdhci.1", NULL),
+ OF_DEV_AUXDATA("samsung,exynos4210-sdhci", EXYNOS4_PA_HSMMC(2),
+ "exynos4-sdhci.2", NULL),
+ OF_DEV_AUXDATA("samsung,exynos4210-sdhci", EXYNOS4_PA_HSMMC(3),
+ "exynos4-sdhci.3", NULL),
+ OF_DEV_AUXDATA("samsung,s3c2440-i2c", EXYNOS4_PA_IIC(0),
+ "s3c2440-i2c.0", NULL),
+ OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA0, "dma-pl330.0", NULL),
+ OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA1, "dma-pl330.1", NULL),
+ {},
+};
+
+static void __init exynos4210_dt_map_io(void)
+{
+ s5p_init_io(NULL, 0, S5P_VA_CHIPID);
+ s3c24xx_init_clocks(24000000);
+}
+
+static void __init exynos4210_dt_machine_init(void)
+{
+ of_platform_populate(NULL, of_default_bus_match_table,
+ exynos4210_auxdata_lookup, NULL);
+}
+
+static char const *exynos4210_dt_compat[] __initdata = {
+ "samsung,exynos4210",
+ NULL
+};
+
+DT_MACHINE_START(EXYNOS4210_DT, "Samsung Exynos4 (Flattened Device Tree)")
+ /* Maintainer: Thomas Abraham <thomas.abraham@linaro.org> */
+ .init_irq = exynos4_init_irq,
+ .map_io = exynos4210_dt_map_io,
+ .init_machine = exynos4210_dt_machine_init,
+ .timer = &exynos4_timer,
+ .dt_compat = exynos4210_dt_compat,
+MACHINE_END
+++ /dev/null
-/* linux/arch/arm/mach-exynos4/setup-sdhci.c
- *
- * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * EXYNOS4 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *exynos4_hsmmc_clksrcs[4] = {
- [0] = NULL,
- [1] = NULL,
- [2] = "sclk_mmc", /* mmc_bus */
- [3] = NULL,
-};
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
-static struct s3c24xx_uart_clksrc bast_serial_clocks[] = {
- [0] = {
- .name = "uclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- },
- [1] = {
- .name = "pclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- }
-};
-
-
static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = {
[0] = {
.hwport = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = bast_serial_clocks,
- .clocks_size = ARRAY_SIZE(bast_serial_clocks),
},
[1] = {
.hwport = 1,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = bast_serial_clocks,
- .clocks_size = ARRAY_SIZE(bast_serial_clocks),
},
/* port 2 is not actually used */
[2] = {
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = bast_serial_clocks,
- .clocks_size = ARRAY_SIZE(bast_serial_clocks),
}
};
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
-/* uart clock source(s) */
-
-static struct s3c24xx_uart_clksrc vr1000_serial_clocks[] = {
- [0] = {
- .name = "uclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- },
- [1] = {
- .name = "pclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0.
- }
-};
-
static struct s3c2410_uartcfg vr1000_uartcfgs[] __initdata = {
[0] = {
.hwport = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = vr1000_serial_clocks,
- .clocks_size = ARRAY_SIZE(vr1000_serial_clocks),
},
[1] = {
.hwport = 1,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = vr1000_serial_clocks,
- .clocks_size = ARRAY_SIZE(vr1000_serial_clocks),
},
/* port 2 is not actually used */
[2] = {
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = vr1000_serial_clocks,
- .clocks_size = ARRAY_SIZE(vr1000_serial_clocks),
-
}
};
.id = -1,
};
+static struct clk_lookup s3c2410_clk_lookup[] = {
+ CLKDEV_INIT(NULL, "clk_uart_baud0", &clk_p),
+ CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk),
+};
+
void __init s3c2410_init_clocks(int xtal)
{
s3c24xx_register_baseclocks(xtal);
s3c2410_setup_clocks();
s3c2410_baseclk_add();
s3c24xx_register_clock(&s3c2410_armclk);
+ clkdev_add_table(s3c2410_clk_lookup, ARRAY_SIZE(s3c2410_clk_lookup));
}
struct sysdev_class s3c2410_sysclass = {
&clk_armclk,
};
+static struct clk_lookup s3c2412_clk_lookup[] = {
+ CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk),
+ CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
+ CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_usysclk),
+};
+
int __init s3c2412_baseclk_add(void)
{
unsigned long clkcon = __raw_readl(S3C2410_CLKCON);
s3c2412_clkcon_enable(clkp, 0);
}
+ clkdev_add_table(s3c2412_clk_lookup, ARRAY_SIZE(s3c2412_clk_lookup));
s3c_pwmclk_init();
return 0;
}
#obj-$(CONFIG_S3C2416_DMA) += dma.o
# Device setup
-obj-$(CONFIG_S3C2416_SETUP_SDHCI) += setup-sdhci.o
obj-$(CONFIG_S3C2416_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
# Machine support
},
};
-static struct clksrc_clk hsmmc_mux[] = {
- [0] = {
- .clk = {
- .name = "hsmmc-if",
- .devname = "s3c-sdhci.0",
- .ctrlbit = (1 << 6),
- .enable = s3c2443_clkcon_enable_s,
- },
- .sources = &(struct clksrc_sources) {
- .nr_sources = 2,
- .sources = (struct clk *[]) {
- [0] = &hsmmc_div[0].clk,
- [1] = NULL, /* to fix */
- },
- },
- .reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 16 },
+static struct clksrc_clk hsmmc_mux0 = {
+ .clk = {
+ .name = "hsmmc-if",
+ .devname = "s3c-sdhci.0",
+ .ctrlbit = (1 << 6),
+ .enable = s3c2443_clkcon_enable_s,
},
- [1] = {
- .clk = {
- .name = "hsmmc-if",
- .devname = "s3c-sdhci.1",
- .ctrlbit = (1 << 12),
- .enable = s3c2443_clkcon_enable_s,
+ .sources = &(struct clksrc_sources) {
+ .nr_sources = 2,
+ .sources = (struct clk * []) {
+ [0] = &hsmmc_div[0].clk,
+ [1] = NULL, /* to fix */
},
- .sources = &(struct clksrc_sources) {
- .nr_sources = 2,
- .sources = (struct clk *[]) {
- [0] = &hsmmc_div[1].clk,
- [1] = NULL, /* to fix */
- },
+ },
+ .reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 16 },
+};
+
+static struct clksrc_clk hsmmc_mux1 = {
+ .clk = {
+ .name = "hsmmc-if",
+ .devname = "s3c-sdhci.1",
+ .ctrlbit = (1 << 12),
+ .enable = s3c2443_clkcon_enable_s,
+ },
+ .sources = &(struct clksrc_sources) {
+ .nr_sources = 2,
+ .sources = (struct clk * []) {
+ [0] = &hsmmc_div[1].clk,
+ [1] = NULL, /* to fix */
},
- .reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 17 },
},
+ .reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 17 },
};
static struct clk hsmmc0_clk = {
&hsspi_mux,
&hsmmc_div[0],
&hsmmc_div[1],
- &hsmmc_mux[0],
- &hsmmc_mux[1],
+ &hsmmc_mux0,
+ &hsmmc_mux1,
+};
+
+static struct clk_lookup s3c2416_clk_lookup[] = {
+ CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &hsmmc0_clk),
+ CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &hsmmc_mux0.clk),
+ CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &hsmmc_mux1.clk),
};
void __init s3c2416_init_clocks(int xtal)
s3c_register_clksrc(clksrcs[ptr], 1);
s3c24xx_register_clock(&hsmmc0_clk);
+ clkdev_add_table(s3c2416_clk_lookup, ARRAY_SIZE(s3c2416_clk_lookup));
s3c_pwmclk_init();
+++ /dev/null
-/* linux/arch/arm/mach-s3c2416/setup-sdhci.c
- *
- * Copyright 2010 Promwad Innovation Company
- * Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
- *
- * S3C2416 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * Based on mach-s3c64xx/setup-sdhci.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *s3c2416_hsmmc_clksrcs[4] = {
- [0] = "hsmmc",
- [1] = "hsmmc",
- [2] = "hsmmc-if",
- /* [3] = "48m", - note not successfully used yet */
-};
#include <linux/mutex.h>
#include <linux/clk.h>
#include <linux/io.h>
+#include <linux/serial_core.h>
#include <mach/hardware.h>
#include <linux/atomic.h>
#include <plat/clock.h>
#include <plat/cpu.h>
+#include <plat/regs-serial.h>
/* S3C2440 extended clock support */
.ctrlbit = S3C2440_CLKCON_CAMERA,
};
+static unsigned long s3c2440_fclk_n_getrate(struct clk *clk)
+{
+ unsigned long ucon0, ucon1, ucon2, divisor;
+
+ /* the fun of calculating the uart divisors on the s3c2440 */
+ ucon0 = __raw_readl(S3C24XX_VA_UART0 + S3C2410_UCON);
+ ucon1 = __raw_readl(S3C24XX_VA_UART1 + S3C2410_UCON);
+ ucon2 = __raw_readl(S3C24XX_VA_UART2 + S3C2410_UCON);
+
+ ucon0 &= S3C2440_UCON0_DIVMASK;
+ ucon1 &= S3C2440_UCON1_DIVMASK;
+ ucon2 &= S3C2440_UCON2_DIVMASK;
+
+ if (ucon0 != 0)
+ divisor = (ucon0 >> S3C2440_UCON_DIVSHIFT) + 6;
+ else if (ucon1 != 0)
+ divisor = (ucon1 >> S3C2440_UCON_DIVSHIFT) + 21;
+ else if (ucon2 != 0)
+ divisor = (ucon2 >> S3C2440_UCON_DIVSHIFT) + 36;
+ else
+ /* manual calims 44, seems to be 9 */
+ divisor = 9;
+
+ return clk_get_rate(clk->parent) / divisor;
+}
+
+static struct clk s3c2440_clk_fclk_n = {
+ .name = "fclk_n",
+ .parent = &clk_f,
+ .ops = &(struct clk_ops) {
+ .get_rate = s3c2440_fclk_n_getrate,
+ },
+};
+
+static struct clk_lookup s3c2440_clk_lookup[] = {
+ CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk),
+ CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
+ CLKDEV_INIT(NULL, "clk_uart_baud3", &s3c2440_clk_fclk_n),
+};
+
static int s3c2440_clk_add(struct sys_device *sysdev)
{
struct clk *clock_upll;
s3c2440_clk_cam.parent = clock_h;
s3c2440_clk_ac97.parent = clock_p;
s3c2440_clk_cam_upll.parent = clock_upll;
+ s3c24xx_register_clock(&s3c2440_clk_fclk_n);
s3c24xx_register_clock(&s3c2440_clk_ac97);
s3c24xx_register_clock(&s3c2440_clk_cam);
s3c24xx_register_clock(&s3c2440_clk_cam_upll);
+ clkdev_add_table(s3c2440_clk_lookup, ARRAY_SIZE(s3c2440_clk_lookup));
clk_disable(&s3c2440_clk_ac97);
clk_disable(&s3c2440_clk_cam);
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
-static struct s3c24xx_uart_clksrc anubis_serial_clocks[] = {
- [0] = {
- .name = "uclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- },
- [1] = {
- .name = "pclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- }
-};
-
-
static struct s3c2410_uartcfg anubis_uartcfgs[] __initdata = {
[0] = {
.hwport = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = anubis_serial_clocks,
- .clocks_size = ARRAY_SIZE(anubis_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
},
[1] = {
.hwport = 2,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = anubis_serial_clocks,
- .clocks_size = ARRAY_SIZE(anubis_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
},
};
#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE)
#define UFCON (S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE)
-static struct s3c24xx_uart_clksrc at2440evb_serial_clocks[] = {
- [0] = {
- .name = "uclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- },
- [1] = {
- .name = "pclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- }
-};
-
-
static struct s3c2410_uartcfg at2440evb_uartcfgs[] __initdata = {
[0] = {
.hwport = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = at2440evb_serial_clocks,
- .clocks_size = ARRAY_SIZE(at2440evb_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
},
[1] = {
.hwport = 1,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = at2440evb_serial_clocks,
- .clocks_size = ARRAY_SIZE(at2440evb_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
},
};
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
-static struct s3c24xx_uart_clksrc osiris_serial_clocks[] = {
- [0] = {
- .name = "uclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- },
- [1] = {
- .name = "pclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- }
-};
-
static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = {
[0] = {
.hwport = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = osiris_serial_clocks,
- .clocks_size = ARRAY_SIZE(osiris_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
},
[1] = {
.hwport = 1,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = osiris_serial_clocks,
- .clocks_size = ARRAY_SIZE(osiris_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
},
[2] = {
.hwport = 2,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
- .clocks = osiris_serial_clocks,
- .clocks_size = ARRAY_SIZE(osiris_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
}
};
static struct map_desc rx1950_iodesc[] __initdata = {
};
-static struct s3c24xx_uart_clksrc rx1950_serial_clocks[] = {
- [0] = {
- .name = "fclk",
- .divisor = 0x0a,
- .min_baud = 0,
- .max_baud = 0,
- },
-};
-
static struct s3c2410_uartcfg rx1950_uartcfgs[] __initdata = {
[0] = {
.hwport = 0,
.ucon = 0x3c5,
.ulcon = 0x03,
.ufcon = 0x51,
- .clocks = rx1950_serial_clocks,
- .clocks_size = ARRAY_SIZE(rx1950_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL3,
},
[1] = {
.hwport = 1,
.ucon = 0x3c5,
.ulcon = 0x03,
.ufcon = 0x51,
- .clocks = rx1950_serial_clocks,
- .clocks_size = ARRAY_SIZE(rx1950_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL3,
},
/* IR port */
[2] = {
.ucon = 0x3c5,
.ulcon = 0x43,
.ufcon = 0xf1,
- .clocks = rx1950_serial_clocks,
- .clocks_size = ARRAY_SIZE(rx1950_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL3,
},
};
},
};
-
-static struct s3c24xx_uart_clksrc rx3715_serial_clocks[] = {
- [0] = {
- .name = "fclk",
- .divisor = 0,
- .min_baud = 0,
- .max_baud = 0,
- }
-};
-
static struct s3c2410_uartcfg rx3715_uartcfgs[] = {
[0] = {
.hwport = 0,
.ucon = 0x3c5,
.ulcon = 0x03,
.ufcon = 0x51,
- .clocks = rx3715_serial_clocks,
- .clocks_size = ARRAY_SIZE(rx3715_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL3,
},
[1] = {
.hwport = 1,
.ucon = 0x3c5,
.ulcon = 0x03,
.ufcon = 0x00,
- .clocks = rx3715_serial_clocks,
- .clocks_size = ARRAY_SIZE(rx3715_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL3,
},
/* IR port */
[2] = {
.ucon = 0x3c5,
.ulcon = 0x43,
.ufcon = 0x51,
- .clocks = rx3715_serial_clocks,
- .clocks_size = ARRAY_SIZE(rx3715_serial_clocks),
+ .clk_sel = S3C2410_UCON_CLKSEL3,
}
};
help
Common setup code for S3C64XX SDHCI GPIO configurations
+config S3C64XX_SETUP_SPI
+ bool
+ help
+ Common setup code for SPI GPIO configurations
+
# S36400 Macchine support
config MACH_SMDK6400
select S3C64XX_SETUP_IDE
select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_KEYPAD
+ select S3C64XX_SETUP_SPI
select SAMSUNG_DEV_ADC
select SAMSUNG_DEV_KEYPAD
select S3C_DEV_USB_HOST
select S3C_DEV_I2C1
select S3C_DEV_WDT
select S3C_DEV_RTC
- select S3C64XX_DEV_SPI
+ select S3C64XX_DEV_SPI0
select S3C24XX_GPIO_EXTRA128
select I2C
help
obj-$(CONFIG_S3C64XX_SETUP_I2C1) += setup-i2c1.o
obj-$(CONFIG_S3C64XX_SETUP_IDE) += setup-ide.o
obj-$(CONFIG_S3C64XX_SETUP_KEYPAD) += setup-keypad.o
-obj-$(CONFIG_S3C64XX_SETUP_SDHCI) += setup-sdhci.o
obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP) += setup-fb-24bpp.o
obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
+obj-$(CONFIG_S3C64XX_SETUP_SPI) += setup-spi.o
# PM
obj-y += dev-uart.o
obj-y += dev-audio.o
-obj-$(CONFIG_S3C64XX_DEV_SPI) += dev-spi.o
.parent = &clk_p,
.enable = s3c64xx_pclk_ctrl,
.ctrlbit = S3C_CLKCON_PCLK_SPI1,
- }, {
- .name = "spi_48m",
- .devname = "s3c64xx-spi.0",
- .parent = &clk_48m,
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_SPI0_48,
- }, {
- .name = "spi_48m",
- .devname = "s3c64xx-spi.1",
- .parent = &clk_48m,
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_SPI1_48,
}, {
.name = "48m",
.devname = "s3c-sdhci.0",
},
};
+static struct clk clk_48m_spi0 = {
+ .name = "spi_48m",
+ .devname = "s3c64xx-spi.0",
+ .parent = &clk_48m,
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_SPI0_48,
+};
+
+static struct clk clk_48m_spi1 = {
+ .name = "spi_48m",
+ .devname = "s3c64xx-spi.1",
+ .parent = &clk_48m,
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_SPI1_48,
+};
+
static struct clk init_clocks[] = {
{
.name = "lcd",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_UHOST,
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.0",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_HSMMC0,
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.1",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_HSMMC1,
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.2",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_HSMMC2,
}, {
.name = "otg",
.parent = &clk_h,
}
};
+static struct clk clk_hsmmc0 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.0",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_HSMMC0,
+};
+
+static struct clk clk_hsmmc1 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.1",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_HSMMC1,
+};
+
+static struct clk clk_hsmmc2 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.2",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_HSMMC2,
+};
static struct clk clk_fout_apll = {
.name = "fout_apll",
static struct clksrc_clk clksrcs[] = {
{
- .clk = {
- .name = "mmc_bus",
- .devname = "s3c-sdhci.0",
- .ctrlbit = S3C_CLKCON_SCLK_MMC0,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 18, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV1, .shift = 0, .size = 4 },
- .sources = &clkset_spi_mmc,
- }, {
- .clk = {
- .name = "mmc_bus",
- .devname = "s3c-sdhci.1",
- .ctrlbit = S3C_CLKCON_SCLK_MMC1,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 20, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV1, .shift = 4, .size = 4 },
- .sources = &clkset_spi_mmc,
- }, {
- .clk = {
- .name = "mmc_bus",
- .devname = "s3c-sdhci.2",
- .ctrlbit = S3C_CLKCON_SCLK_MMC2,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 22, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV1, .shift = 8, .size = 4 },
- .sources = &clkset_spi_mmc,
- }, {
.clk = {
.name = "usb-bus-host",
.ctrlbit = S3C_CLKCON_SCLK_UHOST,
.reg_src = { .reg = S3C_CLK_SRC, .shift = 5, .size = 2 },
.reg_div = { .reg = S3C_CLK_DIV1, .shift = 20, .size = 4 },
.sources = &clkset_uhost,
- }, {
- .clk = {
- .name = "uclk1",
- .ctrlbit = S3C_CLKCON_SCLK_UART,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 13, .size = 1 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 16, .size = 4 },
- .sources = &clkset_uart,
- }, {
-/* Where does UCLK0 come from? */
- .clk = {
- .name = "spi-bus",
- .devname = "s3c64xx-spi.0",
- .ctrlbit = S3C_CLKCON_SCLK_SPI0,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 14, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 0, .size = 4 },
- .sources = &clkset_spi_mmc,
- }, {
- .clk = {
- .name = "spi-bus",
- .devname = "s3c64xx-spi.1",
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 16, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 4, .size = 4 },
- .sources = &clkset_spi_mmc,
}, {
.clk = {
.name = "audio-bus",
},
};
+/* Where does UCLK0 come from? */
+static struct clksrc_clk clk_sclk_uclk = {
+ .clk = {
+ .name = "uclk1",
+ .ctrlbit = S3C_CLKCON_SCLK_UART,
+ .enable = s3c64xx_sclk_ctrl,
+ },
+ .reg_src = { .reg = S3C_CLK_SRC, .shift = 13, .size = 1 },
+ .reg_div = { .reg = S3C_CLK_DIV2, .shift = 16, .size = 4 },
+ .sources = &clkset_uart,
+};
+
+static struct clksrc_clk clk_sclk_mmc0 = {
+ .clk = {
+ .name = "mmc_bus",
+ .devname = "s3c-sdhci.0",
+ .ctrlbit = S3C_CLKCON_SCLK_MMC0,
+ .enable = s3c64xx_sclk_ctrl,
+ },
+ .reg_src = { .reg = S3C_CLK_SRC, .shift = 18, .size = 2 },
+ .reg_div = { .reg = S3C_CLK_DIV1, .shift = 0, .size = 4 },
+ .sources = &clkset_spi_mmc,
+};
+
+static struct clksrc_clk clk_sclk_mmc1 = {
+ .clk = {
+ .name = "mmc_bus",
+ .devname = "s3c-sdhci.1",
+ .ctrlbit = S3C_CLKCON_SCLK_MMC1,
+ .enable = s3c64xx_sclk_ctrl,
+ },
+ .reg_src = { .reg = S3C_CLK_SRC, .shift = 20, .size = 2 },
+ .reg_div = { .reg = S3C_CLK_DIV1, .shift = 4, .size = 4 },
+ .sources = &clkset_spi_mmc,
+};
+
+static struct clksrc_clk clk_sclk_mmc2 = {
+ .clk = {
+ .name = "mmc_bus",
+ .devname = "s3c-sdhci.2",
+ .ctrlbit = S3C_CLKCON_SCLK_MMC2,
+ .enable = s3c64xx_sclk_ctrl,
+ },
+ .reg_src = { .reg = S3C_CLK_SRC, .shift = 22, .size = 2 },
+ .reg_div = { .reg = S3C_CLK_DIV1, .shift = 8, .size = 4 },
+ .sources = &clkset_spi_mmc,
+};
+
+static struct clksrc_clk clk_sclk_spi0 = {
+ .clk = {
+ .name = "spi-bus",
+ .devname = "s3c64xx-spi.0",
+ .ctrlbit = S3C_CLKCON_SCLK_SPI0,
+ .enable = s3c64xx_sclk_ctrl,
+ },
+ .reg_src = { .reg = S3C_CLK_SRC, .shift = 14, .size = 2 },
+ .reg_div = { .reg = S3C_CLK_DIV2, .shift = 0, .size = 4 },
+ .sources = &clkset_spi_mmc,
+};
+
+static struct clksrc_clk clk_sclk_spi1 = {
+ .clk = {
+ .name = "spi-bus",
+ .devname = "s3c64xx-spi.1",
+ .ctrlbit = S3C_CLKCON_SCLK_SPI1,
+ .enable = s3c64xx_sclk_ctrl,
+ },
+ .reg_src = { .reg = S3C_CLK_SRC, .shift = 16, .size = 2 },
+ .reg_div = { .reg = S3C_CLK_DIV2, .shift = 4, .size = 4 },
+ .sources = &clkset_spi_mmc,
+};
+
/* Clock initialisation code */
static struct clksrc_clk *init_parents[] = {
&clk_mout_mpll,
};
+static struct clksrc_clk *clksrc_cdev[] = {
+ &clk_sclk_uclk,
+ &clk_sclk_mmc0,
+ &clk_sclk_mmc1,
+ &clk_sclk_mmc2,
+ &clk_sclk_spi0,
+ &clk_sclk_spi1,
+};
+
+static struct clk *clk_cdev[] = {
+ &clk_hsmmc0,
+ &clk_hsmmc1,
+ &clk_hsmmc2,
+ &clk_48m_spi0,
+ &clk_48m_spi1,
+};
+
+static struct clk_lookup s3c64xx_clk_lookup[] = {
+ CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
+ CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
+ CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &clk_hsmmc0),
+ CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &clk_hsmmc1),
+ CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.0", &clk_hsmmc2),
+ CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
+ CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
+ CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
+ CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
+ CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+ CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_48m_spi0),
+ CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+ CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk2", &clk_48m_spi1),
+};
+
#define GET_DIV(clk, field) ((((clk) & field##_MASK) >> field##_SHIFT) + 1)
void __init_or_cpufreq s3c6400_setup_clocks(void)
void __init s3c64xx_register_clocks(unsigned long xtal,
unsigned armclk_divlimit)
{
+ unsigned int cnt;
+
armclk_mask = armclk_divlimit;
s3c24xx_register_baseclocks(xtal);
s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+ s3c24xx_register_clocks(clk_cdev, ARRAY_SIZE(clk_cdev));
+ for (cnt = 0; cnt < ARRAY_SIZE(clk_cdev); cnt++)
+ s3c_disable_clocks(clk_cdev[cnt], 1);
+
s3c24xx_register_clocks(clks1, ARRAY_SIZE(clks1));
s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
+ for (cnt = 0; cnt < ARRAY_SIZE(clksrc_cdev); cnt++)
+ s3c_register_clksrc(clksrc_cdev[cnt], 1);
+ clkdev_add_table(s3c64xx_clk_lookup, ARRAY_SIZE(s3c64xx_clk_lookup));
+
s3c_pwmclk_init();
}
+++ /dev/null
-/* linux/arch/arm/plat-s3c64xx/dev-spi.c
- *
- * Copyright (C) 2009 Samsung Electronics Ltd.
- * Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/export.h>
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-
-#include <mach/dma.h>
-#include <mach/map.h>
-#include <mach/spi-clocks.h>
-#include <mach/irqs.h>
-
-#include <plat/s3c64xx-spi.h>
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-
-static char *spi_src_clks[] = {
- [S3C64XX_SPI_SRCCLK_PCLK] = "pclk",
- [S3C64XX_SPI_SRCCLK_SPIBUS] = "spi-bus",
- [S3C64XX_SPI_SRCCLK_48M] = "spi_48m",
-};
-
-/* SPI Controller platform_devices */
-
-/* Since we emulate multi-cs capability, we do not touch the GPC-3,7.
- * The emulated CS is toggled by board specific mechanism, as it can
- * be either some immediate GPIO or some signal out of some other
- * chip in between ... or some yet another way.
- * We simply do not assume anything about CS.
- */
-static int s3c64xx_spi_cfg_gpio(struct platform_device *pdev)
-{
- unsigned int base;
-
- switch (pdev->id) {
- case 0:
- base = S3C64XX_GPC(0);
- break;
-
- case 1:
- base = S3C64XX_GPC(4);
- break;
-
- default:
- dev_err(&pdev->dev, "Invalid SPI Controller number!");
- return -EINVAL;
- }
-
- s3c_gpio_cfgall_range(base, 3,
- S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-
- return 0;
-}
-
-static struct resource s3c64xx_spi0_resource[] = {
- [0] = {
- .start = S3C64XX_PA_SPI0,
- .end = S3C64XX_PA_SPI0 + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMACH_SPI0_TX,
- .end = DMACH_SPI0_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMACH_SPI0_RX,
- .end = DMACH_SPI0_RX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = IRQ_SPI0,
- .end = IRQ_SPI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct s3c64xx_spi_info s3c64xx_spi0_pdata = {
- .cfg_gpio = s3c64xx_spi_cfg_gpio,
- .fifo_lvl_mask = 0x7f,
- .rx_lvl_offset = 13,
- .tx_st_done = 21,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-struct platform_device s3c64xx_device_spi0 = {
- .name = "s3c64xx-spi",
- .id = 0,
- .num_resources = ARRAY_SIZE(s3c64xx_spi0_resource),
- .resource = s3c64xx_spi0_resource,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s3c64xx_spi0_pdata,
- },
-};
-EXPORT_SYMBOL(s3c64xx_device_spi0);
-
-static struct resource s3c64xx_spi1_resource[] = {
- [0] = {
- .start = S3C64XX_PA_SPI1,
- .end = S3C64XX_PA_SPI1 + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMACH_SPI1_TX,
- .end = DMACH_SPI1_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMACH_SPI1_RX,
- .end = DMACH_SPI1_RX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = IRQ_SPI1,
- .end = IRQ_SPI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct s3c64xx_spi_info s3c64xx_spi1_pdata = {
- .cfg_gpio = s3c64xx_spi_cfg_gpio,
- .fifo_lvl_mask = 0x7f,
- .rx_lvl_offset = 13,
- .tx_st_done = 21,
-};
-
-struct platform_device s3c64xx_device_spi1 = {
- .name = "s3c64xx-spi",
- .id = 1,
- .num_resources = ARRAY_SIZE(s3c64xx_spi1_resource),
- .resource = s3c64xx_spi1_resource,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s3c64xx_spi1_pdata,
- },
-};
-EXPORT_SYMBOL(s3c64xx_device_spi1);
-
-void __init s3c64xx_spi_set_info(int cntrlr, int src_clk_nr, int num_cs)
-{
- struct s3c64xx_spi_info *pd;
-
- /* Reject invalid configuration */
- if (!num_cs || src_clk_nr < 0
- || src_clk_nr > S3C64XX_SPI_SRCCLK_48M) {
- printk(KERN_ERR "%s: Invalid SPI configuration\n", __func__);
- return;
- }
-
- switch (cntrlr) {
- case 0:
- pd = &s3c64xx_spi0_pdata;
- break;
- case 1:
- pd = &s3c64xx_spi1_pdata;
- break;
- default:
- printk(KERN_ERR "%s: Invalid SPI controller(%d)\n",
- __func__, cntrlr);
- return;
- }
-
- pd->num_cs = num_cs;
- pd->src_clk_nr = src_clk_nr;
- pd->src_clk_name = spi_src_clks[src_clk_nr];
-}
#define S3C_PA_USB_HSOTG S3C64XX_PA_USB_HSOTG
#define S3C_PA_RTC S3C64XX_PA_RTC
#define S3C_PA_WDT S3C64XX_PA_WATCHDOG
+#define S3C_PA_SPI0 S3C64XX_PA_SPI0
+#define S3C_PA_SPI1 S3C64XX_PA_SPI1
#define SAMSUNG_PA_ADC S3C64XX_PA_ADC
#define SAMSUNG_PA_CFCON S3C64XX_PA_CFCON
+++ /dev/null
-/* linux/arch/arm/mach-s3c64xx/setup-sdhci.c
- *
- * Copyright 2008 Simtec Electronics
- * Copyright 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- * http://armlinux.simtec.co.uk/
- *
- * S3C6400/S3C6410 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *s3c64xx_hsmmc_clksrcs[4] = {
- [0] = "hsmmc",
- [1] = "hsmmc",
- [2] = "mmc_bus",
- /* [3] = "48m", - note not successfully used yet */
-};
--- /dev/null
+/* linux/arch/arm/mach-s3c64xx/setup-spi.c
+ *
+ * Copyright (C) 2011 Samsung Electronics Ltd.
+ * http://www.samsung.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+
+#include <plat/gpio-cfg.h>
+#include <plat/s3c64xx-spi.h>
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
+ .fifo_lvl_mask = 0x7f,
+ .rx_lvl_offset = 13,
+ .tx_st_done = 21,
+};
+
+int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+{
+ s3c_gpio_cfgall_range(S3C64XX_GPC(0), 3,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
+ .fifo_lvl_mask = 0x7f,
+ .rx_lvl_offset = 13,
+ .tx_st_done = 21,
+};
+
+int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+{
+ s3c_gpio_cfgall_range(S3C64XX_GPC(4), 3,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ return 0;
+}
+#endif
help
Common setup code for i2c bus 1.
+config S5P64X0_SETUP_SPI
+ bool
+ help
+ Common setup code for SPI GPIO configurations
+
# machine support
config MACH_SMDK6440
select S3C_DEV_I2C1
select S3C_DEV_RTC
select S3C_DEV_WDT
- select S3C64XX_DEV_SPI
select SAMSUNG_DEV_ADC
select SAMSUNG_DEV_BACKLIGHT
select SAMSUNG_DEV_PWM
select S3C_DEV_I2C1
select S3C_DEV_RTC
select S3C_DEV_WDT
- select S3C64XX_DEV_SPI
select SAMSUNG_DEV_ADC
select SAMSUNG_DEV_BACKLIGHT
select SAMSUNG_DEV_PWM
# device support
obj-y += dev-audio.o
-obj-$(CONFIG_S3C64XX_DEV_SPI) += dev-spi.o
obj-$(CONFIG_S5P64X0_SETUP_I2C1) += setup-i2c1.o
obj-$(CONFIG_S5P64X0_SETUP_FB_24BPP) += setup-fb-24bpp.o
+obj-$(CONFIG_S5P64X0_SETUP_SPI) += setup-spi.o
.parent = &clk_pclk.clk,
.enable = s5p64x0_pclk_ctrl,
.ctrlbit = (1 << 31),
- }, {
- .name = "sclk_spi_48",
- .devname = "s3c64xx-spi.0",
- .parent = &clk_48m,
- .enable = s5p64x0_sclk_ctrl,
- .ctrlbit = (1 << 22),
- }, {
- .name = "sclk_spi_48",
- .devname = "s3c64xx-spi.1",
- .parent = &clk_48m,
- .enable = s5p64x0_sclk_ctrl,
- .ctrlbit = (1 << 23),
}, {
.name = "mmc_48m",
.devname = "s3c-sdhci.0",
.sources = &clkset_group1,
.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 22, .size = 2 },
.reg_div = { .reg = S5P64X0_CLK_DIV1, .shift = 8, .size = 4 },
- }, {
- .clk = {
- .name = "uclk1",
- .ctrlbit = (1 << 5),
- .enable = s5p64x0_sclk_ctrl,
- },
- .sources = &clkset_uart,
- .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 13, .size = 1 },
- .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 16, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_spi",
- .devname = "s3c64xx-spi.0",
- .ctrlbit = (1 << 20),
- .enable = s5p64x0_sclk_ctrl,
- },
- .sources = &clkset_group1,
- .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 14, .size = 2 },
- .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 0, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_spi",
- .devname = "s3c64xx-spi.1",
- .ctrlbit = (1 << 21),
- .enable = s5p64x0_sclk_ctrl,
- },
- .sources = &clkset_group1,
- .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 16, .size = 2 },
- .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 4, .size = 4 },
}, {
.clk = {
.name = "sclk_post",
},
};
+static struct clksrc_clk clk_sclk_uclk = {
+ .clk = {
+ .name = "uclk1",
+ .ctrlbit = (1 << 5),
+ .enable = s5p64x0_sclk_ctrl,
+ },
+ .sources = &clkset_uart,
+ .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 13, .size = 1 },
+ .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 16, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi0 = {
+ .clk = {
+ .name = "sclk_spi",
+ .devname = "s3c64xx-spi.0",
+ .ctrlbit = (1 << 20),
+ .enable = s5p64x0_sclk_ctrl,
+ },
+ .sources = &clkset_group1,
+ .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 14, .size = 2 },
+ .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi1 = {
+ .clk = {
+ .name = "sclk_spi",
+ .devname = "s3c64xx-spi.1",
+ .ctrlbit = (1 << 21),
+ .enable = s5p64x0_sclk_ctrl,
+ },
+ .sources = &clkset_group1,
+ .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 16, .size = 2 },
+ .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 4, .size = 4 },
+};
+
/* Clock initialization code */
static struct clksrc_clk *sysclks[] = {
&clk_mout_apll,
.id = -1,
};
+static struct clksrc_clk *clksrc_cdev[] = {
+ &clk_sclk_uclk,
+ &clk_sclk_spi0,
+ &clk_sclk_spi1,
+};
+
+static struct clk_lookup s5p6440_clk_lookup[] = {
+ CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_pclk_low.clk),
+ CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
+ CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
+ CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+ CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+};
+
void __init_or_cpufreq s5p6440_setup_clocks(void)
{
struct clk *xtal_clk;
s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
+ for (ptr = 0; ptr < ARRAY_SIZE(clksrc_cdev); ptr++)
+ s3c_register_clksrc(clksrc_cdev[ptr], 1);
s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+ clkdev_add_table(s5p6440_clk_lookup, ARRAY_SIZE(s5p6440_clk_lookup));
s3c24xx_register_clock(&dummy_apb_pclk);
.sources = &clkset_group2,
.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 22, .size = 2 },
.reg_div = { .reg = S5P64X0_CLK_DIV1, .shift = 8, .size = 4 },
- }, {
- .clk = {
- .name = "uclk1",
- .ctrlbit = (1 << 5),
- .enable = s5p64x0_sclk_ctrl,
- },
- .sources = &clkset_uart,
- .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 13, .size = 1 },
- .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 16, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_spi",
- .devname = "s3c64xx-spi.0",
- .ctrlbit = (1 << 20),
- .enable = s5p64x0_sclk_ctrl,
- },
- .sources = &clkset_group2,
- .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 14, .size = 2 },
- .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 0, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_spi",
- .devname = "s3c64xx-spi.1",
- .ctrlbit = (1 << 21),
- .enable = s5p64x0_sclk_ctrl,
- },
- .sources = &clkset_group2,
- .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 16, .size = 2 },
- .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 4, .size = 4 },
}, {
.clk = {
.name = "sclk_fimc",
},
};
+static struct clksrc_clk clk_sclk_uclk = {
+ .clk = {
+ .name = "uclk1",
+ .ctrlbit = (1 << 5),
+ .enable = s5p64x0_sclk_ctrl,
+ },
+ .sources = &clkset_uart,
+ .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 13, .size = 1 },
+ .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 16, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi0 = {
+ .clk = {
+ .name = "sclk_spi",
+ .devname = "s3c64xx-spi.0",
+ .ctrlbit = (1 << 20),
+ .enable = s5p64x0_sclk_ctrl,
+ },
+ .sources = &clkset_group2,
+ .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 14, .size = 2 },
+ .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi1 = {
+ .clk = {
+ .name = "sclk_spi",
+ .devname = "s3c64xx-spi.1",
+ .ctrlbit = (1 << 21),
+ .enable = s5p64x0_sclk_ctrl,
+ },
+ .sources = &clkset_group2,
+ .reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 16, .size = 2 },
+ .reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 4, .size = 4 },
+};
+
+static struct clksrc_clk *clksrc_cdev[] = {
+ &clk_sclk_uclk,
+ &clk_sclk_spi0,
+ &clk_sclk_spi1,
+};
+
+static struct clk_lookup s5p6450_clk_lookup[] = {
+ CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_pclk_low.clk),
+ CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
+ CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
+ CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+ CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+};
+
/* Clock initialization code */
static struct clksrc_clk *sysclks[] = {
&clk_mout_apll,
s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
+ for (ptr = 0; ptr < ARRAY_SIZE(clksrc_cdev); ptr++)
+ s3c_register_clksrc(clksrc_cdev[ptr], 1);
s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+ clkdev_add_table(s5p6450_clk_lookup, ARRAY_SIZE(s5p6450_clk_lookup));
s3c24xx_register_clock(&dummy_apb_pclk);
+++ /dev/null
-/* linux/arch/arm/mach-s5p64x0/dev-spi.c
- *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * Copyright (C) 2010 Samsung Electronics Co. Ltd.
- * Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-
-#include <mach/dma.h>
-#include <mach/map.h>
-#include <mach/irqs.h>
-#include <mach/regs-clock.h>
-#include <mach/spi-clocks.h>
-
-#include <plat/cpu.h>
-#include <plat/s3c64xx-spi.h>
-#include <plat/gpio-cfg.h>
-
-static char *s5p64x0_spi_src_clks[] = {
- [S5P64X0_SPI_SRCCLK_PCLK] = "pclk",
- [S5P64X0_SPI_SRCCLK_SCLK] = "sclk_spi",
-};
-
-/* SPI Controller platform_devices */
-
-/* Since we emulate multi-cs capability, we do not touch the CS.
- * The emulated CS is toggled by board specific mechanism, as it can
- * be either some immediate GPIO or some signal out of some other
- * chip in between ... or some yet another way.
- * We simply do not assume anything about CS.
- */
-static int s5p6440_spi_cfg_gpio(struct platform_device *pdev)
-{
- unsigned int base;
-
- switch (pdev->id) {
- case 0:
- base = S5P6440_GPC(0);
- break;
-
- case 1:
- base = S5P6440_GPC(4);
- break;
-
- default:
- dev_err(&pdev->dev, "Invalid SPI Controller number!");
- return -EINVAL;
- }
-
- s3c_gpio_cfgall_range(base, 3,
- S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-
- return 0;
-}
-
-static int s5p6450_spi_cfg_gpio(struct platform_device *pdev)
-{
- unsigned int base;
-
- switch (pdev->id) {
- case 0:
- base = S5P6450_GPC(0);
- break;
-
- case 1:
- base = S5P6450_GPC(4);
- break;
-
- default:
- dev_err(&pdev->dev, "Invalid SPI Controller number!");
- return -EINVAL;
- }
-
- s3c_gpio_cfgall_range(base, 3,
- S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-
- return 0;
-}
-
-static struct resource s5p64x0_spi0_resource[] = {
- [0] = {
- .start = S5P64X0_PA_SPI0,
- .end = S5P64X0_PA_SPI0 + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMACH_SPI0_TX,
- .end = DMACH_SPI0_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMACH_SPI0_RX,
- .end = DMACH_SPI0_RX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = IRQ_SPI0,
- .end = IRQ_SPI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct s3c64xx_spi_info s5p6440_spi0_pdata = {
- .cfg_gpio = s5p6440_spi_cfg_gpio,
- .fifo_lvl_mask = 0x1ff,
- .rx_lvl_offset = 15,
- .tx_st_done = 25,
-};
-
-static struct s3c64xx_spi_info s5p6450_spi0_pdata = {
- .cfg_gpio = s5p6450_spi_cfg_gpio,
- .fifo_lvl_mask = 0x1ff,
- .rx_lvl_offset = 15,
- .tx_st_done = 25,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-struct platform_device s5p64x0_device_spi0 = {
- .name = "s3c64xx-spi",
- .id = 0,
- .num_resources = ARRAY_SIZE(s5p64x0_spi0_resource),
- .resource = s5p64x0_spi0_resource,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
-
-static struct resource s5p64x0_spi1_resource[] = {
- [0] = {
- .start = S5P64X0_PA_SPI1,
- .end = S5P64X0_PA_SPI1 + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMACH_SPI1_TX,
- .end = DMACH_SPI1_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMACH_SPI1_RX,
- .end = DMACH_SPI1_RX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = IRQ_SPI1,
- .end = IRQ_SPI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct s3c64xx_spi_info s5p6440_spi1_pdata = {
- .cfg_gpio = s5p6440_spi_cfg_gpio,
- .fifo_lvl_mask = 0x7f,
- .rx_lvl_offset = 15,
- .tx_st_done = 25,
-};
-
-static struct s3c64xx_spi_info s5p6450_spi1_pdata = {
- .cfg_gpio = s5p6450_spi_cfg_gpio,
- .fifo_lvl_mask = 0x7f,
- .rx_lvl_offset = 15,
- .tx_st_done = 25,
-};
-
-struct platform_device s5p64x0_device_spi1 = {
- .name = "s3c64xx-spi",
- .id = 1,
- .num_resources = ARRAY_SIZE(s5p64x0_spi1_resource),
- .resource = s5p64x0_spi1_resource,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
-
-void __init s5p64x0_spi_set_info(int cntrlr, int src_clk_nr, int num_cs)
-{
- struct s3c64xx_spi_info *pd;
-
- /* Reject invalid configuration */
- if (!num_cs || src_clk_nr < 0
- || src_clk_nr > S5P64X0_SPI_SRCCLK_SCLK) {
- printk(KERN_ERR "%s: Invalid SPI configuration\n", __func__);
- return;
- }
-
- switch (cntrlr) {
- case 0:
- if (soc_is_s5p6450())
- pd = &s5p6450_spi0_pdata;
- else
- pd = &s5p6440_spi0_pdata;
-
- s5p64x0_device_spi0.dev.platform_data = pd;
- break;
- case 1:
- if (soc_is_s5p6450())
- pd = &s5p6450_spi1_pdata;
- else
- pd = &s5p6440_spi1_pdata;
-
- s5p64x0_device_spi1.dev.platform_data = pd;
- break;
- default:
- printk(KERN_ERR "%s: Invalid SPI controller(%d)\n",
- __func__, cntrlr);
- return;
- }
-
- pd->num_cs = num_cs;
- pd->src_clk_nr = src_clk_nr;
- pd->src_clk_name = s5p64x0_spi_src_clks[src_clk_nr];
-}
static u64 dma_dmamask = DMA_BIT_MASK(32);
-struct dma_pl330_peri s5p6440_pdma_peri[22] = {
- {
- .peri_id = (u8)DMACH_UART0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART3_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART3_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = DMACH_MAX,
- }, {
- .peri_id = DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_PCM0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_SPI1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI1_RX,
- .rqtype = DEVTOMEM,
- },
+u8 s5p6440_pdma_peri[] = {
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART1_RX,
+ DMACH_UART1_TX,
+ DMACH_UART2_RX,
+ DMACH_UART2_TX,
+ DMACH_UART3_RX,
+ DMACH_UART3_TX,
+ DMACH_MAX,
+ DMACH_MAX,
+ DMACH_PCM0_TX,
+ DMACH_PCM0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S0_RX,
+ DMACH_SPI0_TX,
+ DMACH_SPI0_RX,
+ DMACH_MAX,
+ DMACH_MAX,
+ DMACH_MAX,
+ DMACH_MAX,
+ DMACH_SPI1_TX,
+ DMACH_SPI1_RX,
};
struct dma_pl330_platdata s5p6440_pdma_pdata = {
.nr_valid_peri = ARRAY_SIZE(s5p6440_pdma_peri),
- .peri = s5p6440_pdma_peri,
+ .peri_id = s5p6440_pdma_peri,
};
-struct dma_pl330_peri s5p6450_pdma_peri[32] = {
- {
- .peri_id = (u8)DMACH_UART0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART3_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART3_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART4_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART4_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_USI_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_USI_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_I2S1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PWM,
- }, {
- .peri_id = (u8)DMACH_UART5_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART5_TX,
- .rqtype = MEMTODEV,
- },
+u8 s5p6450_pdma_peri[] = {
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART1_RX,
+ DMACH_UART1_TX,
+ DMACH_UART2_RX,
+ DMACH_UART2_TX,
+ DMACH_UART3_RX,
+ DMACH_UART3_TX,
+ DMACH_UART4_RX,
+ DMACH_UART4_TX,
+ DMACH_PCM0_TX,
+ DMACH_PCM0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S0_RX,
+ DMACH_SPI0_TX,
+ DMACH_SPI0_RX,
+ DMACH_PCM1_TX,
+ DMACH_PCM1_RX,
+ DMACH_PCM2_TX,
+ DMACH_PCM2_RX,
+ DMACH_SPI1_TX,
+ DMACH_SPI1_RX,
+ DMACH_USI_TX,
+ DMACH_USI_RX,
+ DMACH_MAX,
+ DMACH_I2S1_TX,
+ DMACH_I2S1_RX,
+ DMACH_I2S2_TX,
+ DMACH_I2S2_RX,
+ DMACH_PWM,
+ DMACH_UART5_RX,
+ DMACH_UART5_TX,
};
struct dma_pl330_platdata s5p6450_pdma_pdata = {
.nr_valid_peri = ARRAY_SIZE(s5p6450_pdma_peri),
- .peri = s5p6450_pdma_peri,
+ .peri_id = s5p6450_pdma_peri,
};
struct amba_device s5p64x0_device_pdma = {
static int __init s5p64x0_dma_init(void)
{
- if (soc_is_s5p6450())
+ if (soc_is_s5p6450()) {
+ dma_cap_set(DMA_SLAVE, s5p6450_pdma_pdata.cap_mask);
+ dma_cap_set(DMA_CYCLIC, s5p6450_pdma_pdata.cap_mask);
s5p64x0_device_pdma.dev.platform_data = &s5p6450_pdma_pdata;
- else
+ } else {
+ dma_cap_set(DMA_SLAVE, s5p6440_pdma_pdata.cap_mask);
+ dma_cap_set(DMA_CYCLIC, s5p6440_pdma_pdata.cap_mask);
s5p64x0_device_pdma.dev.platform_data = &s5p6440_pdma_pdata;
+ }
amba_device_register(&s5p64x0_device_pdma, &iomem_resource);
#define IRQ_EINT_GROUP(grp, x) (IRQ_EINT_GROUP##grp##_BASE + (x))
+#define IRQ_TIMER_BASE (11)
+
/* Set the default NR_IRQS */
#define NR_IRQS (IRQ_EINT_GROUP8_BASE + IRQ_EINT_GROUP8_NR + 1)
#define S3C_PA_RTC S5P64X0_PA_RTC
#define S3C_PA_WDT S5P64X0_PA_WDT
#define S3C_PA_FB S5P64X0_PA_FB
+#define S3C_PA_SPI0 S5P64X0_PA_SPI0
+#define S3C_PA_SPI1 S5P64X0_PA_SPI1
#define S5P_PA_CHIPID S5P64X0_PA_CHIPID
#define S5P_PA_SROMC S5P64X0_PA_SROMC
#include <plat/s5p6450.h>
#include <plat/regs-serial.h>
-static struct s3c24xx_uart_clksrc s5p64x0_serial_clocks[] = {
- [0] = {
- .name = "pclk_low",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- },
- [1] = {
- .name = "uclk1",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- },
-};
-
/* uart registration process */
-
-void __init s5p64x0_common_init_uarts(struct s3c2410_uartcfg *cfg, int no)
-{
- struct s3c2410_uartcfg *tcfg = cfg;
- u32 ucnt;
-
- for (ucnt = 0; ucnt < no; ucnt++, tcfg++) {
- if (!tcfg->clocks) {
- tcfg->clocks = s5p64x0_serial_clocks;
- tcfg->clocks_size = ARRAY_SIZE(s5p64x0_serial_clocks);
- }
- }
-}
-
void __init s5p6440_init_uarts(struct s3c2410_uartcfg *cfg, int no)
{
int uart;
s5p_uart_resources[uart].resources->end = S5P6440_PA_UART(uart) + S5P_SZ_UART;
}
- s5p64x0_common_init_uarts(cfg, no);
s3c24xx_init_uartdevs("s3c6400-uart", s5p_uart_resources, cfg, no);
}
void __init s5p6450_init_uarts(struct s3c2410_uartcfg *cfg, int no)
{
- s5p64x0_common_init_uarts(cfg, no);
s3c24xx_init_uartdevs("s3c6400-uart", s5p_uart_resources, cfg, no);
}
--- /dev/null
+/* linux/arch/arm/mach-s5p64x0/setup-spi.c
+ *
+ * Copyright (C) 2011 Samsung Electronics Ltd.
+ * http://www.samsung.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+#include <plat/gpio-cfg.h>
+#include <plat/cpu.h>
+#include <plat/s3c64xx-spi.h>
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
+ .fifo_lvl_mask = 0x1ff,
+ .rx_lvl_offset = 15,
+ .tx_st_done = 25,
+};
+
+int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+{
+ if (soc_is_s5p6450())
+ s3c_gpio_cfgall_range(S5P6450_GPC(0), 3,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ else
+ s3c_gpio_cfgall_range(S5P6440_GPC(0), 3,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
+ .fifo_lvl_mask = 0x7f,
+ .rx_lvl_offset = 15,
+ .tx_st_done = 25,
+};
+
+int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+{
+ if (soc_is_s5p6450())
+ s3c_gpio_cfgall_range(S5P6450_GPC(4), 3,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ else
+ s3c_gpio_cfgall_range(S5P6440_GPC(4), 3,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ return 0;
+}
+#endif
help
Common setup code for SDHCI gpio.
+config S5PC100_SETUP_SPI
+ bool
+ help
+ Common setup code for SPI GPIO configurations.
+
config MACH_SMDKC100
bool "SMDKC100"
select CPU_S5PC100
obj-$(CONFIG_S5PC100_SETUP_I2C1) += setup-i2c1.o
obj-$(CONFIG_S5PC100_SETUP_IDE) += setup-ide.o
obj-$(CONFIG_S5PC100_SETUP_KEYPAD) += setup-keypad.o
-obj-$(CONFIG_S5PC100_SETUP_SDHCI) += setup-sdhci.o
obj-$(CONFIG_S5PC100_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
+obj-$(CONFIG_S5PC100_SETUP_SPI) += setup-spi.o
# device support
obj-y += dev-audio.o
-obj-$(CONFIG_S3C64XX_DEV_SPI) += dev-spi.o
# machine support
.parent = &clk_div_d0_bus.clk,
.enable = s5pc100_d0_2_ctrl,
.ctrlbit = (1 << 1),
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.2",
- .parent = &clk_div_d1_bus.clk,
- .enable = s5pc100_d1_0_ctrl,
- .ctrlbit = (1 << 7),
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.1",
- .parent = &clk_div_d1_bus.clk,
- .enable = s5pc100_d1_0_ctrl,
- .ctrlbit = (1 << 6),
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.0",
- .parent = &clk_div_d1_bus.clk,
- .enable = s5pc100_d1_0_ctrl,
- .ctrlbit = (1 << 5),
}, {
.name = "modemif",
.parent = &clk_div_d1_bus.clk,
.parent = &clk_div_pclkd1.clk,
.enable = s5pc100_d1_5_ctrl,
.ctrlbit = (1 << 8),
- }, {
- .name = "spi_48m",
- .devname = "s3c64xx-spi.0",
- .parent = &clk_mout_48m.clk,
- .enable = s5pc100_sclk0_ctrl,
- .ctrlbit = (1 << 7),
- }, {
- .name = "spi_48m",
- .devname = "s3c64xx-spi.1",
- .parent = &clk_mout_48m.clk,
- .enable = s5pc100_sclk0_ctrl,
- .ctrlbit = (1 << 8),
- }, {
- .name = "spi_48m",
- .devname = "s3c64xx-spi.2",
- .parent = &clk_mout_48m.clk,
- .enable = s5pc100_sclk0_ctrl,
- .ctrlbit = (1 << 9),
}, {
.name = "mmc_48m",
.devname = "s3c-sdhci.0",
},
};
+static struct clk clk_hsmmc2 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.2",
+ .parent = &clk_div_d1_bus.clk,
+ .enable = s5pc100_d1_0_ctrl,
+ .ctrlbit = (1 << 7),
+};
+
+static struct clk clk_hsmmc1 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.1",
+ .parent = &clk_div_d1_bus.clk,
+ .enable = s5pc100_d1_0_ctrl,
+ .ctrlbit = (1 << 6),
+};
+
+static struct clk clk_hsmmc0 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.0",
+ .parent = &clk_div_d1_bus.clk,
+ .enable = s5pc100_d1_0_ctrl,
+ .ctrlbit = (1 << 5),
+};
+
+static struct clk clk_48m_spi0 = {
+ .name = "spi_48m",
+ .devname = "s3c64xx-spi.0",
+ .parent = &clk_mout_48m.clk,
+ .enable = s5pc100_sclk0_ctrl,
+ .ctrlbit = (1 << 7),
+};
+
+static struct clk clk_48m_spi1 = {
+ .name = "spi_48m",
+ .devname = "s3c64xx-spi.1",
+ .parent = &clk_mout_48m.clk,
+ .enable = s5pc100_sclk0_ctrl,
+ .ctrlbit = (1 << 8),
+};
+
+static struct clk clk_48m_spi2 = {
+ .name = "spi_48m",
+ .devname = "s3c64xx-spi.2",
+ .parent = &clk_mout_48m.clk,
+ .enable = s5pc100_sclk0_ctrl,
+ .ctrlbit = (1 << 9),
+};
+
static struct clk clk_vclk54m = {
.name = "vclk_54m",
.rate = 54000000,
static struct clksrc_clk clksrcs[] = {
{
- .clk = {
- .name = "sclk_spi",
- .devname = "s3c64xx-spi.0",
- .ctrlbit = (1 << 4),
- .enable = s5pc100_sclk0_ctrl,
-
- },
- .sources = &clk_src_group1,
- .reg_src = { .reg = S5P_CLK_SRC1, .shift = 4, .size = 2 },
- .reg_div = { .reg = S5P_CLK_DIV2, .shift = 4, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_spi",
- .devname = "s3c64xx-spi.1",
- .ctrlbit = (1 << 5),
- .enable = s5pc100_sclk0_ctrl,
-
- },
- .sources = &clk_src_group1,
- .reg_src = { .reg = S5P_CLK_SRC1, .shift = 8, .size = 2 },
- .reg_div = { .reg = S5P_CLK_DIV2, .shift = 8, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_spi",
- .devname = "s3c64xx-spi.2",
- .ctrlbit = (1 << 6),
- .enable = s5pc100_sclk0_ctrl,
-
- },
- .sources = &clk_src_group1,
- .reg_src = { .reg = S5P_CLK_SRC1, .shift = 12, .size = 2 },
- .reg_div = { .reg = S5P_CLK_DIV2, .shift = 12, .size = 4 },
- }, {
- .clk = {
- .name = "uclk1",
- .ctrlbit = (1 << 3),
- .enable = s5pc100_sclk0_ctrl,
-
- },
- .sources = &clk_src_group2,
- .reg_src = { .reg = S5P_CLK_SRC1, .shift = 0, .size = 1 },
- .reg_div = { .reg = S5P_CLK_DIV2, .shift = 0, .size = 4 },
- }, {
.clk = {
.name = "sclk_mixer",
.ctrlbit = (1 << 6),
.sources = &clk_src_group7,
.reg_src = { .reg = S5P_CLK_SRC2, .shift = 24, .size = 2 },
.reg_div = { .reg = S5P_CLK_DIV3, .shift = 24, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.0",
- .ctrlbit = (1 << 12),
- .enable = s5pc100_sclk1_ctrl,
-
- },
- .sources = &clk_src_mmc0,
- .reg_src = { .reg = S5P_CLK_SRC2, .shift = 0, .size = 2 },
- .reg_div = { .reg = S5P_CLK_DIV3, .shift = 0, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.1",
- .ctrlbit = (1 << 13),
- .enable = s5pc100_sclk1_ctrl,
-
- },
- .sources = &clk_src_mmc12,
- .reg_src = { .reg = S5P_CLK_SRC2, .shift = 4, .size = 2 },
- .reg_div = { .reg = S5P_CLK_DIV3, .shift = 4, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.2",
- .ctrlbit = (1 << 14),
- .enable = s5pc100_sclk1_ctrl,
-
- },
- .sources = &clk_src_mmc12,
- .reg_src = { .reg = S5P_CLK_SRC2, .shift = 8, .size = 2 },
- .reg_div = { .reg = S5P_CLK_DIV3, .shift = 8, .size = 4 },
}, {
.clk = {
.name = "sclk_irda",
},
};
+static struct clksrc_clk clk_sclk_uart = {
+ .clk = {
+ .name = "uclk1",
+ .ctrlbit = (1 << 3),
+ .enable = s5pc100_sclk0_ctrl,
+ },
+ .sources = &clk_src_group2,
+ .reg_src = { .reg = S5P_CLK_SRC1, .shift = 0, .size = 1 },
+ .reg_div = { .reg = S5P_CLK_DIV2, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc0 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.0",
+ .ctrlbit = (1 << 12),
+ .enable = s5pc100_sclk1_ctrl,
+ },
+ .sources = &clk_src_mmc0,
+ .reg_src = { .reg = S5P_CLK_SRC2, .shift = 0, .size = 2 },
+ .reg_div = { .reg = S5P_CLK_DIV3, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc1 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.1",
+ .ctrlbit = (1 << 13),
+ .enable = s5pc100_sclk1_ctrl,
+ },
+ .sources = &clk_src_mmc12,
+ .reg_src = { .reg = S5P_CLK_SRC2, .shift = 4, .size = 2 },
+ .reg_div = { .reg = S5P_CLK_DIV3, .shift = 4, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc2 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.2",
+ .ctrlbit = (1 << 14),
+ .enable = s5pc100_sclk1_ctrl,
+ },
+ .sources = &clk_src_mmc12,
+ .reg_src = { .reg = S5P_CLK_SRC2, .shift = 8, .size = 2 },
+ .reg_div = { .reg = S5P_CLK_DIV3, .shift = 8, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi0 = {
+ .clk = {
+ .name = "sclk_spi",
+ .devname = "s3c64xx-spi.0",
+ .ctrlbit = (1 << 4),
+ .enable = s5pc100_sclk0_ctrl,
+ },
+ .sources = &clk_src_group1,
+ .reg_src = { .reg = S5P_CLK_SRC1, .shift = 4, .size = 2 },
+ .reg_div = { .reg = S5P_CLK_DIV2, .shift = 4, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi1 = {
+ .clk = {
+ .name = "sclk_spi",
+ .devname = "s3c64xx-spi.1",
+ .ctrlbit = (1 << 5),
+ .enable = s5pc100_sclk0_ctrl,
+ },
+ .sources = &clk_src_group1,
+ .reg_src = { .reg = S5P_CLK_SRC1, .shift = 8, .size = 2 },
+ .reg_div = { .reg = S5P_CLK_DIV2, .shift = 8, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi2 = {
+ .clk = {
+ .name = "sclk_spi",
+ .devname = "s3c64xx-spi.2",
+ .ctrlbit = (1 << 6),
+ .enable = s5pc100_sclk0_ctrl,
+ },
+ .sources = &clk_src_group1,
+ .reg_src = { .reg = S5P_CLK_SRC1, .shift = 12, .size = 2 },
+ .reg_div = { .reg = S5P_CLK_DIV2, .shift = 12, .size = 4 },
+};
+
/* Clock initialisation code */
static struct clksrc_clk *sysclks[] = {
&clk_mout_apll,
&clk_sclk_spdif,
};
+static struct clk *clk_cdev[] = {
+ &clk_hsmmc0,
+ &clk_hsmmc1,
+ &clk_hsmmc2,
+ &clk_48m_spi0,
+ &clk_48m_spi1,
+ &clk_48m_spi2,
+};
+
+static struct clksrc_clk *clksrc_cdev[] = {
+ &clk_sclk_uart,
+ &clk_sclk_mmc0,
+ &clk_sclk_mmc1,
+ &clk_sclk_mmc2,
+ &clk_sclk_spi0,
+ &clk_sclk_spi1,
+ &clk_sclk_spi2,
+};
+
void __init_or_cpufreq s5pc100_setup_clocks(void)
{
unsigned long xtal;
&clk_pcmcdclk1,
};
+static struct clk_lookup s5pc100_clk_lookup[] = {
+ CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
+ CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uart.clk),
+ CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &clk_hsmmc0),
+ CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &clk_hsmmc1),
+ CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.0", &clk_hsmmc2),
+ CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
+ CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
+ CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
+ CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
+ CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_48m_spi0),
+ CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_sclk_spi0.clk),
+ CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_48m_spi1),
+ CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk2", &clk_sclk_spi1.clk),
+ CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk1", &clk_48m_spi2),
+ CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk2", &clk_sclk_spi2.clk),
+};
+
void __init s5pc100_register_clocks(void)
{
int ptr;
s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
+ for (ptr = 0; ptr < ARRAY_SIZE(clksrc_cdev); ptr++)
+ s3c_register_clksrc(clksrc_cdev[ptr], 1);
s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+ clkdev_add_table(s5pc100_clk_lookup, ARRAY_SIZE(s5pc100_clk_lookup));
+
+ s3c24xx_register_clocks(clk_cdev, ARRAY_SIZE(clk_cdev));
+ for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++)
+ s3c_disable_clocks(clk_cdev[ptr], 1);
s3c24xx_register_clock(&dummy_apb_pclk);
+++ /dev/null
-/* linux/arch/arm/mach-s5pc100/dev-spi.c
- *
- * Copyright (C) 2010 Samsung Electronics Co. Ltd.
- * Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-
-#include <mach/dma.h>
-#include <mach/map.h>
-#include <mach/spi-clocks.h>
-#include <mach/irqs.h>
-
-#include <plat/s3c64xx-spi.h>
-#include <plat/gpio-cfg.h>
-#include <plat/irqs.h>
-
-static char *spi_src_clks[] = {
- [S5PC100_SPI_SRCCLK_PCLK] = "pclk",
- [S5PC100_SPI_SRCCLK_48M] = "spi_48m",
- [S5PC100_SPI_SRCCLK_SPIBUS] = "spi_bus",
-};
-
-/* SPI Controller platform_devices */
-
-/* Since we emulate multi-cs capability, we do not touch the CS.
- * The emulated CS is toggled by board specific mechanism, as it can
- * be either some immediate GPIO or some signal out of some other
- * chip in between ... or some yet another way.
- * We simply do not assume anything about CS.
- */
-static int s5pc100_spi_cfg_gpio(struct platform_device *pdev)
-{
- switch (pdev->id) {
- case 0:
- s3c_gpio_cfgall_range(S5PC100_GPB(0), 3,
- S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
- break;
-
- case 1:
- s3c_gpio_cfgall_range(S5PC100_GPB(4), 3,
- S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
- break;
-
- case 2:
- s3c_gpio_cfgpin(S5PC100_GPG3(0), S3C_GPIO_SFN(3));
- s3c_gpio_setpull(S5PC100_GPG3(0), S3C_GPIO_PULL_UP);
- s3c_gpio_cfgall_range(S5PC100_GPB(2), 2,
- S3C_GPIO_SFN(3), S3C_GPIO_PULL_UP);
- break;
-
- default:
- dev_err(&pdev->dev, "Invalid SPI Controller number!");
- return -EINVAL;
- }
-
- return 0;
-}
-
-static struct resource s5pc100_spi0_resource[] = {
- [0] = {
- .start = S5PC100_PA_SPI0,
- .end = S5PC100_PA_SPI0 + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMACH_SPI0_TX,
- .end = DMACH_SPI0_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMACH_SPI0_RX,
- .end = DMACH_SPI0_RX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = IRQ_SPI0,
- .end = IRQ_SPI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct s3c64xx_spi_info s5pc100_spi0_pdata = {
- .cfg_gpio = s5pc100_spi_cfg_gpio,
- .fifo_lvl_mask = 0x7f,
- .rx_lvl_offset = 13,
- .high_speed = 1,
- .tx_st_done = 21,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-struct platform_device s5pc100_device_spi0 = {
- .name = "s3c64xx-spi",
- .id = 0,
- .num_resources = ARRAY_SIZE(s5pc100_spi0_resource),
- .resource = s5pc100_spi0_resource,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s5pc100_spi0_pdata,
- },
-};
-
-static struct resource s5pc100_spi1_resource[] = {
- [0] = {
- .start = S5PC100_PA_SPI1,
- .end = S5PC100_PA_SPI1 + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMACH_SPI1_TX,
- .end = DMACH_SPI1_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMACH_SPI1_RX,
- .end = DMACH_SPI1_RX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = IRQ_SPI1,
- .end = IRQ_SPI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct s3c64xx_spi_info s5pc100_spi1_pdata = {
- .cfg_gpio = s5pc100_spi_cfg_gpio,
- .fifo_lvl_mask = 0x7f,
- .rx_lvl_offset = 13,
- .high_speed = 1,
- .tx_st_done = 21,
-};
-
-struct platform_device s5pc100_device_spi1 = {
- .name = "s3c64xx-spi",
- .id = 1,
- .num_resources = ARRAY_SIZE(s5pc100_spi1_resource),
- .resource = s5pc100_spi1_resource,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s5pc100_spi1_pdata,
- },
-};
-
-static struct resource s5pc100_spi2_resource[] = {
- [0] = {
- .start = S5PC100_PA_SPI2,
- .end = S5PC100_PA_SPI2 + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMACH_SPI2_TX,
- .end = DMACH_SPI2_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMACH_SPI2_RX,
- .end = DMACH_SPI2_RX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = IRQ_SPI2,
- .end = IRQ_SPI2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct s3c64xx_spi_info s5pc100_spi2_pdata = {
- .cfg_gpio = s5pc100_spi_cfg_gpio,
- .fifo_lvl_mask = 0x7f,
- .rx_lvl_offset = 13,
- .high_speed = 1,
- .tx_st_done = 21,
-};
-
-struct platform_device s5pc100_device_spi2 = {
- .name = "s3c64xx-spi",
- .id = 2,
- .num_resources = ARRAY_SIZE(s5pc100_spi2_resource),
- .resource = s5pc100_spi2_resource,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s5pc100_spi2_pdata,
- },
-};
-
-void __init s5pc100_spi_set_info(int cntrlr, int src_clk_nr, int num_cs)
-{
- struct s3c64xx_spi_info *pd;
-
- /* Reject invalid configuration */
- if (!num_cs || src_clk_nr < 0
- || src_clk_nr > S5PC100_SPI_SRCCLK_SPIBUS) {
- printk(KERN_ERR "%s: Invalid SPI configuration\n", __func__);
- return;
- }
-
- switch (cntrlr) {
- case 0:
- pd = &s5pc100_spi0_pdata;
- break;
- case 1:
- pd = &s5pc100_spi1_pdata;
- break;
- case 2:
- pd = &s5pc100_spi2_pdata;
- break;
- default:
- printk(KERN_ERR "%s: Invalid SPI controller(%d)\n",
- __func__, cntrlr);
- return;
- }
-
- pd->num_cs = num_cs;
- pd->src_clk_nr = src_clk_nr;
- pd->src_clk_name = spi_src_clks[src_clk_nr];
-}
static u64 dma_dmamask = DMA_BIT_MASK(32);
-struct dma_pl330_peri pdma0_peri[30] = {
- {
- .peri_id = (u8)DMACH_UART0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART3_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART3_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = DMACH_IRDA,
- }, {
- .peri_id = (u8)DMACH_I2S0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0S_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_AC97_MICIN,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_AC97_PCMIN,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_AC97_PCMOUT,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_EXTERNAL,
- }, {
- .peri_id = (u8)DMACH_PWM,
- }, {
- .peri_id = (u8)DMACH_SPDIF,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_HSI_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_HSI_TX,
- .rqtype = MEMTODEV,
- },
+u8 pdma0_peri[] = {
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART1_RX,
+ DMACH_UART1_TX,
+ DMACH_UART2_RX,
+ DMACH_UART2_TX,
+ DMACH_UART3_RX,
+ DMACH_UART3_TX,
+ DMACH_IRDA,
+ DMACH_I2S0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S0S_TX,
+ DMACH_I2S1_RX,
+ DMACH_I2S1_TX,
+ DMACH_I2S2_RX,
+ DMACH_I2S2_TX,
+ DMACH_SPI0_RX,
+ DMACH_SPI0_TX,
+ DMACH_SPI1_RX,
+ DMACH_SPI1_TX,
+ DMACH_SPI2_RX,
+ DMACH_SPI2_TX,
+ DMACH_AC97_MICIN,
+ DMACH_AC97_PCMIN,
+ DMACH_AC97_PCMOUT,
+ DMACH_EXTERNAL,
+ DMACH_PWM,
+ DMACH_SPDIF,
+ DMACH_HSI_RX,
+ DMACH_HSI_TX,
};
struct dma_pl330_platdata s5pc100_pdma0_pdata = {
.nr_valid_peri = ARRAY_SIZE(pdma0_peri),
- .peri = pdma0_peri,
+ .peri_id = pdma0_peri,
};
struct amba_device s5pc100_device_pdma0 = {
.periphid = 0x00041330,
};
-struct dma_pl330_peri pdma1_peri[30] = {
- {
- .peri_id = (u8)DMACH_UART0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART3_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART3_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = DMACH_IRDA,
- }, {
- .peri_id = (u8)DMACH_I2S0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0S_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ0,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ1,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ2,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ3,
- },
+u8 pdma1_peri[] = {
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART1_RX,
+ DMACH_UART1_TX,
+ DMACH_UART2_RX,
+ DMACH_UART2_TX,
+ DMACH_UART3_RX,
+ DMACH_UART3_TX,
+ DMACH_IRDA,
+ DMACH_I2S0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S0S_TX,
+ DMACH_I2S1_RX,
+ DMACH_I2S1_TX,
+ DMACH_I2S2_RX,
+ DMACH_I2S2_TX,
+ DMACH_SPI0_RX,
+ DMACH_SPI0_TX,
+ DMACH_SPI1_RX,
+ DMACH_SPI1_TX,
+ DMACH_SPI2_RX,
+ DMACH_SPI2_TX,
+ DMACH_PCM0_RX,
+ DMACH_PCM0_TX,
+ DMACH_PCM1_RX,
+ DMACH_PCM1_TX,
+ DMACH_MSM_REQ0,
+ DMACH_MSM_REQ1,
+ DMACH_MSM_REQ2,
+ DMACH_MSM_REQ3,
};
struct dma_pl330_platdata s5pc100_pdma1_pdata = {
.nr_valid_peri = ARRAY_SIZE(pdma1_peri),
- .peri = pdma1_peri,
+ .peri_id = pdma1_peri,
};
struct amba_device s5pc100_device_pdma1 = {
static int __init s5pc100_dma_init(void)
{
+ dma_cap_set(DMA_SLAVE, s5pc100_pdma0_pdata.cap_mask);
+ dma_cap_set(DMA_CYCLIC, s5pc100_pdma0_pdata.cap_mask);
amba_device_register(&s5pc100_device_pdma0, &iomem_resource);
+
+ dma_cap_set(DMA_SLAVE, s5pc100_pdma1_pdata.cap_mask);
+ dma_cap_set(DMA_CYCLIC, s5pc100_pdma1_pdata.cap_mask);
amba_device_register(&s5pc100_device_pdma1, &iomem_resource);
return 0;
#define IRQ_SDMFIQ S5P_IRQ_VIC2(31)
#define IRQ_VIC_END S5P_IRQ_VIC2(31)
+#define IRQ_TIMER_BASE (11)
+
#define S5P_EINT_BASE1 (S5P_IRQ_VIC0(0))
#define S5P_EINT_BASE2 (IRQ_VIC_END + 1)
#define S3C_PA_USB_HSOTG S5PC100_PA_USB_HSOTG
#define S3C_PA_USB_HSPHY S5PC100_PA_USB_HSPHY
#define S3C_PA_WDT S5PC100_PA_WATCHDOG
+#define S3C_PA_SPI0 S5PC100_PA_SPI0
+#define S3C_PA_SPI1 S5PC100_PA_SPI1
+#define S3C_PA_SPI2 S5PC100_PA_SPI2
#define S5P_PA_CHIPID S5PC100_PA_CHIPID
#define S5P_PA_FIMC0 S5PC100_PA_FIMC0
+++ /dev/null
-/* linux/arch/arm/mach-s5pc100/setup-sdhci.c
- *
- * Copyright 2008 Samsung Electronics
- *
- * S5PC100 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * Based on mach-s3c6410/setup-sdhci.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *s5pc100_hsmmc_clksrcs[4] = {
- [0] = "hsmmc", /* HCLK */
- /* [1] = "hsmmc", - duplicate HCLK entry */
- [2] = "sclk_mmc", /* mmc_bus */
- /* [3] = "48m", - note not successfully used yet */
-};
--- /dev/null
+/* linux/arch/arm/mach-s5pc100/setup-spi.c
+ *
+ * Copyright (C) 2011 Samsung Electronics Ltd.
+ * http://www.samsung.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+
+#include <plat/gpio-cfg.h>
+#include <plat/s3c64xx-spi.h>
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
+ .fifo_lvl_mask = 0x7f,
+ .rx_lvl_offset = 13,
+ .high_speed = 1,
+ .tx_st_done = 21,
+};
+
+int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+{
+ s3c_gpio_cfgall_range(S5PC100_GPB(0), 3,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
+ .fifo_lvl_mask = 0x7f,
+ .rx_lvl_offset = 13,
+ .high_speed = 1,
+ .tx_st_done = 21,
+};
+
+int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+{
+ s3c_gpio_cfgall_range(S5PC100_GPB(4), 3,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI2
+struct s3c64xx_spi_info s3c64xx_spi2_pdata __initdata = {
+ .fifo_lvl_mask = 0x7f,
+ .rx_lvl_offset = 13,
+ .high_speed = 1,
+ .tx_st_done = 21,
+};
+
+int s3c64xx_spi2_cfg_gpio(struct platform_device *dev)
+{
+ s3c_gpio_cfgpin(S5PC100_GPG3(0), S3C_GPIO_SFN(3));
+ s3c_gpio_setpull(S5PC100_GPG3(0), S3C_GPIO_PULL_UP);
+ s3c_gpio_cfgall_range(S5PC100_GPB(2), 2,
+ S3C_GPIO_SFN(3), S3C_GPIO_PULL_UP);
+ return 0;
+}
+#endif
help
Common setup code for the camera interfaces.
+config S5PV210_SETUP_SPI
+ bool
+ help
+ Common setup code for SPI GPIO configurations.
+
menu "S5PC110 Machines"
config MACH_AQUILA
# device support
obj-y += dev-audio.o
-obj-$(CONFIG_S3C64XX_DEV_SPI) += dev-spi.o
obj-$(CONFIG_S5PV210_SETUP_FB_24BPP) += setup-fb-24bpp.o
obj-$(CONFIG_S5PV210_SETUP_FIMC) += setup-fimc.o
obj-$(CONFIG_S5PV210_SETUP_I2C2) += setup-i2c2.o
obj-$(CONFIG_S5PV210_SETUP_IDE) += setup-ide.o
obj-$(CONFIG_S5PV210_SETUP_KEYPAD) += setup-keypad.o
-obj-$(CONFIG_S5PV210_SETUP_SDHCI) += setup-sdhci.o
obj-$(CONFIG_S5PV210_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
+obj-$(CONFIG_S5PV210_SETUP_SPI) += setup-spi.o
.parent = &clk_hclk_psys.clk,
.enable = s5pv210_clk_ip1_ctrl,
.ctrlbit = (1<<25),
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.0",
- .parent = &clk_hclk_psys.clk,
- .enable = s5pv210_clk_ip2_ctrl,
- .ctrlbit = (1<<16),
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.1",
- .parent = &clk_hclk_psys.clk,
- .enable = s5pv210_clk_ip2_ctrl,
- .ctrlbit = (1<<17),
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.2",
- .parent = &clk_hclk_psys.clk,
- .enable = s5pv210_clk_ip2_ctrl,
- .ctrlbit = (1<<18),
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.3",
- .parent = &clk_hclk_psys.clk,
- .enable = s5pv210_clk_ip2_ctrl,
- .ctrlbit = (1<<19),
}, {
.name = "systimer",
.parent = &clk_pclk_psys.clk,
},
};
+static struct clk clk_hsmmc0 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.0",
+ .parent = &clk_hclk_psys.clk,
+ .enable = s5pv210_clk_ip2_ctrl,
+ .ctrlbit = (1<<16),
+};
+
+static struct clk clk_hsmmc1 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.1",
+ .parent = &clk_hclk_psys.clk,
+ .enable = s5pv210_clk_ip2_ctrl,
+ .ctrlbit = (1<<17),
+};
+
+static struct clk clk_hsmmc2 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.2",
+ .parent = &clk_hclk_psys.clk,
+ .enable = s5pv210_clk_ip2_ctrl,
+ .ctrlbit = (1<<18),
+};
+
+static struct clk clk_hsmmc3 = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.3",
+ .parent = &clk_hclk_psys.clk,
+ .enable = s5pv210_clk_ip2_ctrl,
+ .ctrlbit = (1<<19),
+};
+
static struct clk *clkset_uart_list[] = {
[6] = &clk_mout_mpll.clk,
[7] = &clk_mout_epll.clk,
.sources = &clkset_sclk_onenand,
.reg_src = { .reg = S5P_CLK_SRC0, .shift = 28, .size = 1 },
.reg_div = { .reg = S5P_CLK_DIV6, .shift = 12, .size = 3 },
- }, {
- .clk = {
- .name = "uclk1",
- .devname = "s5pv210-uart.0",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 12),
- },
- .sources = &clkset_uart,
- .reg_src = { .reg = S5P_CLK_SRC4, .shift = 16, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV4, .shift = 16, .size = 4 },
- }, {
- .clk = {
- .name = "uclk1",
- .devname = "s5pv210-uart.1",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 13),
- },
- .sources = &clkset_uart,
- .reg_src = { .reg = S5P_CLK_SRC4, .shift = 20, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV4, .shift = 20, .size = 4 },
- }, {
- .clk = {
- .name = "uclk1",
- .devname = "s5pv210-uart.2",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 14),
- },
- .sources = &clkset_uart,
- .reg_src = { .reg = S5P_CLK_SRC4, .shift = 24, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV4, .shift = 24, .size = 4 },
- }, {
- .clk = {
- .name = "uclk1",
- .devname = "s5pv210-uart.3",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 15),
- },
- .sources = &clkset_uart,
- .reg_src = { .reg = S5P_CLK_SRC4, .shift = 28, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV4, .shift = 28, .size = 4 },
}, {
.clk = {
.name = "sclk_fimc",
.sources = &clkset_group2,
.reg_src = { .reg = S5P_CLK_SRC1, .shift = 20, .size = 4 },
.reg_div = { .reg = S5P_CLK_DIV1, .shift = 20, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.0",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 8),
- },
- .sources = &clkset_group2,
- .reg_src = { .reg = S5P_CLK_SRC4, .shift = 0, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV4, .shift = 0, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.1",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 9),
- },
- .sources = &clkset_group2,
- .reg_src = { .reg = S5P_CLK_SRC4, .shift = 4, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV4, .shift = 4, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.2",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 10),
- },
- .sources = &clkset_group2,
- .reg_src = { .reg = S5P_CLK_SRC4, .shift = 8, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV4, .shift = 8, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_mmc",
- .devname = "s3c-sdhci.3",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 11),
- },
- .sources = &clkset_group2,
- .reg_src = { .reg = S5P_CLK_SRC4, .shift = 12, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV4, .shift = 12, .size = 4 },
}, {
.clk = {
.name = "sclk_mfc",
.sources = &clkset_group2,
.reg_src = { .reg = S5P_CLK_SRC1, .shift = 24, .size = 4 },
.reg_div = { .reg = S5P_CLK_DIV1, .shift = 28, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_spi",
- .devname = "s3c64xx-spi.0",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 16),
- },
- .sources = &clkset_group2,
- .reg_src = { .reg = S5P_CLK_SRC5, .shift = 0, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV5, .shift = 0, .size = 4 },
- }, {
- .clk = {
- .name = "sclk_spi",
- .devname = "s3c64xx-spi.1",
- .enable = s5pv210_clk_mask0_ctrl,
- .ctrlbit = (1 << 17),
- },
- .sources = &clkset_group2,
- .reg_src = { .reg = S5P_CLK_SRC5, .shift = 4, .size = 4 },
- .reg_div = { .reg = S5P_CLK_DIV5, .shift = 4, .size = 4 },
}, {
.clk = {
.name = "sclk_pwi",
},
};
+static struct clksrc_clk clk_sclk_uart0 = {
+ .clk = {
+ .name = "uclk1",
+ .devname = "s5pv210-uart.0",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 12),
+ },
+ .sources = &clkset_uart,
+ .reg_src = { .reg = S5P_CLK_SRC4, .shift = 16, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV4, .shift = 16, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_uart1 = {
+ .clk = {
+ .name = "uclk1",
+ .devname = "s5pv210-uart.1",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 13),
+ },
+ .sources = &clkset_uart,
+ .reg_src = { .reg = S5P_CLK_SRC4, .shift = 20, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV4, .shift = 20, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_uart2 = {
+ .clk = {
+ .name = "uclk1",
+ .devname = "s5pv210-uart.2",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 14),
+ },
+ .sources = &clkset_uart,
+ .reg_src = { .reg = S5P_CLK_SRC4, .shift = 24, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV4, .shift = 24, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_uart3 = {
+ .clk = {
+ .name = "uclk1",
+ .devname = "s5pv210-uart.3",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 15),
+ },
+ .sources = &clkset_uart,
+ .reg_src = { .reg = S5P_CLK_SRC4, .shift = 28, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV4, .shift = 28, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc0 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.0",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 8),
+ },
+ .sources = &clkset_group2,
+ .reg_src = { .reg = S5P_CLK_SRC4, .shift = 0, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV4, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc1 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.1",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 9),
+ },
+ .sources = &clkset_group2,
+ .reg_src = { .reg = S5P_CLK_SRC4, .shift = 4, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV4, .shift = 4, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc2 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.2",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 10),
+ },
+ .sources = &clkset_group2,
+ .reg_src = { .reg = S5P_CLK_SRC4, .shift = 8, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV4, .shift = 8, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc3 = {
+ .clk = {
+ .name = "sclk_mmc",
+ .devname = "s3c-sdhci.3",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 11),
+ },
+ .sources = &clkset_group2,
+ .reg_src = { .reg = S5P_CLK_SRC4, .shift = 12, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV4, .shift = 12, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi0 = {
+ .clk = {
+ .name = "sclk_spi",
+ .devname = "s3c64xx-spi.0",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 16),
+ },
+ .sources = &clkset_group2,
+ .reg_src = { .reg = S5P_CLK_SRC5, .shift = 0, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV5, .shift = 0, .size = 4 },
+ };
+
+static struct clksrc_clk clk_sclk_spi1 = {
+ .clk = {
+ .name = "sclk_spi",
+ .devname = "s3c64xx-spi.1",
+ .enable = s5pv210_clk_mask0_ctrl,
+ .ctrlbit = (1 << 17),
+ },
+ .sources = &clkset_group2,
+ .reg_src = { .reg = S5P_CLK_SRC5, .shift = 4, .size = 4 },
+ .reg_div = { .reg = S5P_CLK_DIV5, .shift = 4, .size = 4 },
+ };
+
+
+static struct clksrc_clk *clksrc_cdev[] = {
+ &clk_sclk_uart0,
+ &clk_sclk_uart1,
+ &clk_sclk_uart2,
+ &clk_sclk_uart3,
+ &clk_sclk_mmc0,
+ &clk_sclk_mmc1,
+ &clk_sclk_mmc2,
+ &clk_sclk_mmc3,
+ &clk_sclk_spi0,
+ &clk_sclk_spi1,
+};
+
+static struct clk *clk_cdev[] = {
+ &clk_hsmmc0,
+ &clk_hsmmc1,
+ &clk_hsmmc2,
+ &clk_hsmmc3,
+};
+
/* Clock initialisation code */
static struct clksrc_clk *sysclks[] = {
&clk_mout_apll,
&clk_pcmcdclk2,
};
+static struct clk_lookup s5pv210_clk_lookup[] = {
+ CLKDEV_INIT(NULL, "clk_uart_baud0", &clk_p),
+ CLKDEV_INIT("s5pv210-uart.0", "clk_uart_baud1", &clk_sclk_uart0.clk),
+ CLKDEV_INIT("s5pv210-uart.1", "clk_uart_baud1", &clk_sclk_uart1.clk),
+ CLKDEV_INIT("s5pv210-uart.2", "clk_uart_baud1", &clk_sclk_uart2.clk),
+ CLKDEV_INIT("s5pv210-uart.3", "clk_uart_baud1", &clk_sclk_uart3.clk),
+ CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &clk_hsmmc0),
+ CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &clk_hsmmc1),
+ CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.0", &clk_hsmmc2),
+ CLKDEV_INIT("s3c-sdhci.3", "mmc_busclk.0", &clk_hsmmc3),
+ CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
+ CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
+ CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
+ CLKDEV_INIT("s3c-sdhci.3", "mmc_busclk.2", &clk_sclk_mmc3.clk),
+ CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
+ CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+ CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+};
+
void __init s5pv210_register_clocks(void)
{
int ptr;
for (ptr = 0; ptr < ARRAY_SIZE(sclk_tv); ptr++)
s3c_register_clksrc(sclk_tv[ptr], 1);
+ for (ptr = 0; ptr < ARRAY_SIZE(clksrc_cdev); ptr++)
+ s3c_register_clksrc(clksrc_cdev[ptr], 1);
+
s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+ clkdev_add_table(s5pv210_clk_lookup, ARRAY_SIZE(s5pv210_clk_lookup));
+
+ s3c24xx_register_clocks(clk_cdev, ARRAY_SIZE(clk_cdev));
+ for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++)
+ s3c_disable_clocks(clk_cdev[ptr], 1);
s3c24xx_register_clock(&dummy_apb_pclk);
s3c_pwmclk_init();
+++ /dev/null
-/* linux/arch/arm/mach-s5pv210/dev-spi.c
- *
- * Copyright (C) 2010 Samsung Electronics Co. Ltd.
- * Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-
-#include <mach/dma.h>
-#include <mach/map.h>
-#include <mach/irqs.h>
-#include <mach/spi-clocks.h>
-
-#include <plat/s3c64xx-spi.h>
-#include <plat/gpio-cfg.h>
-
-static char *spi_src_clks[] = {
- [S5PV210_SPI_SRCCLK_PCLK] = "pclk",
- [S5PV210_SPI_SRCCLK_SCLK] = "sclk_spi",
-};
-
-/* SPI Controller platform_devices */
-
-/* Since we emulate multi-cs capability, we do not touch the CS.
- * The emulated CS is toggled by board specific mechanism, as it can
- * be either some immediate GPIO or some signal out of some other
- * chip in between ... or some yet another way.
- * We simply do not assume anything about CS.
- */
-static int s5pv210_spi_cfg_gpio(struct platform_device *pdev)
-{
- unsigned int base;
-
- switch (pdev->id) {
- case 0:
- base = S5PV210_GPB(0);
- break;
-
- case 1:
- base = S5PV210_GPB(4);
- break;
-
- default:
- dev_err(&pdev->dev, "Invalid SPI Controller number!");
- return -EINVAL;
- }
-
- s3c_gpio_cfgall_range(base, 3,
- S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-
- return 0;
-}
-
-static struct resource s5pv210_spi0_resource[] = {
- [0] = {
- .start = S5PV210_PA_SPI0,
- .end = S5PV210_PA_SPI0 + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMACH_SPI0_TX,
- .end = DMACH_SPI0_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMACH_SPI0_RX,
- .end = DMACH_SPI0_RX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = IRQ_SPI0,
- .end = IRQ_SPI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct s3c64xx_spi_info s5pv210_spi0_pdata = {
- .cfg_gpio = s5pv210_spi_cfg_gpio,
- .fifo_lvl_mask = 0x1ff,
- .rx_lvl_offset = 15,
- .high_speed = 1,
- .tx_st_done = 25,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-struct platform_device s5pv210_device_spi0 = {
- .name = "s3c64xx-spi",
- .id = 0,
- .num_resources = ARRAY_SIZE(s5pv210_spi0_resource),
- .resource = s5pv210_spi0_resource,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s5pv210_spi0_pdata,
- },
-};
-
-static struct resource s5pv210_spi1_resource[] = {
- [0] = {
- .start = S5PV210_PA_SPI1,
- .end = S5PV210_PA_SPI1 + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMACH_SPI1_TX,
- .end = DMACH_SPI1_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMACH_SPI1_RX,
- .end = DMACH_SPI1_RX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = IRQ_SPI1,
- .end = IRQ_SPI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct s3c64xx_spi_info s5pv210_spi1_pdata = {
- .cfg_gpio = s5pv210_spi_cfg_gpio,
- .fifo_lvl_mask = 0x7f,
- .rx_lvl_offset = 15,
- .high_speed = 1,
- .tx_st_done = 25,
-};
-
-struct platform_device s5pv210_device_spi1 = {
- .name = "s3c64xx-spi",
- .id = 1,
- .num_resources = ARRAY_SIZE(s5pv210_spi1_resource),
- .resource = s5pv210_spi1_resource,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s5pv210_spi1_pdata,
- },
-};
-
-void __init s5pv210_spi_set_info(int cntrlr, int src_clk_nr, int num_cs)
-{
- struct s3c64xx_spi_info *pd;
-
- /* Reject invalid configuration */
- if (!num_cs || src_clk_nr < 0
- || src_clk_nr > S5PV210_SPI_SRCCLK_SCLK) {
- printk(KERN_ERR "%s: Invalid SPI configuration\n", __func__);
- return;
- }
-
- switch (cntrlr) {
- case 0:
- pd = &s5pv210_spi0_pdata;
- break;
- case 1:
- pd = &s5pv210_spi1_pdata;
- break;
- default:
- printk(KERN_ERR "%s: Invalid SPI controller(%d)\n",
- __func__, cntrlr);
- return;
- }
-
- pd->num_cs = num_cs;
- pd->src_clk_nr = src_clk_nr;
- pd->src_clk_name = spi_src_clks[src_clk_nr];
-}
static u64 dma_dmamask = DMA_BIT_MASK(32);
-struct dma_pl330_peri pdma0_peri[28] = {
- {
- .peri_id = (u8)DMACH_UART0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART3_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART3_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_I2S0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0S_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_SPI0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_AC97_MICIN,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_AC97_PCMIN,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_AC97_PCMOUT,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_PWM,
- }, {
- .peri_id = (u8)DMACH_SPDIF,
- .rqtype = MEMTODEV,
- },
+u8 pdma0_peri[] = {
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART1_RX,
+ DMACH_UART1_TX,
+ DMACH_UART2_RX,
+ DMACH_UART2_TX,
+ DMACH_UART3_RX,
+ DMACH_UART3_TX,
+ DMACH_MAX,
+ DMACH_I2S0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S0S_TX,
+ DMACH_I2S1_RX,
+ DMACH_I2S1_TX,
+ DMACH_MAX,
+ DMACH_MAX,
+ DMACH_SPI0_RX,
+ DMACH_SPI0_TX,
+ DMACH_SPI1_RX,
+ DMACH_SPI1_TX,
+ DMACH_MAX,
+ DMACH_MAX,
+ DMACH_AC97_MICIN,
+ DMACH_AC97_PCMIN,
+ DMACH_AC97_PCMOUT,
+ DMACH_MAX,
+ DMACH_PWM,
+ DMACH_SPDIF,
};
struct dma_pl330_platdata s5pv210_pdma0_pdata = {
.nr_valid_peri = ARRAY_SIZE(pdma0_peri),
- .peri = pdma0_peri,
+ .peri_id = pdma0_peri,
};
struct amba_device s5pv210_device_pdma0 = {
.periphid = 0x00041330,
};
-struct dma_pl330_peri pdma1_peri[32] = {
- {
- .peri_id = (u8)DMACH_UART0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_UART3_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_UART3_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_I2S0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S0S_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_I2S2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_I2S2_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_SPI1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_SPI1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_MAX,
- }, {
- .peri_id = (u8)DMACH_PCM0_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM0_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_PCM1_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM1_TX,
- .rqtype = MEMTODEV,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ0,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ1,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ2,
- }, {
- .peri_id = (u8)DMACH_MSM_REQ3,
- }, {
- .peri_id = (u8)DMACH_PCM2_RX,
- .rqtype = DEVTOMEM,
- }, {
- .peri_id = (u8)DMACH_PCM2_TX,
- .rqtype = MEMTODEV,
- },
+u8 pdma1_peri[] = {
+ DMACH_UART0_RX,
+ DMACH_UART0_TX,
+ DMACH_UART1_RX,
+ DMACH_UART1_TX,
+ DMACH_UART2_RX,
+ DMACH_UART2_TX,
+ DMACH_UART3_RX,
+ DMACH_UART3_TX,
+ DMACH_MAX,
+ DMACH_I2S0_RX,
+ DMACH_I2S0_TX,
+ DMACH_I2S0S_TX,
+ DMACH_I2S1_RX,
+ DMACH_I2S1_TX,
+ DMACH_I2S2_RX,
+ DMACH_I2S2_TX,
+ DMACH_SPI0_RX,
+ DMACH_SPI0_TX,
+ DMACH_SPI1_RX,
+ DMACH_SPI1_TX,
+ DMACH_MAX,
+ DMACH_MAX,
+ DMACH_PCM0_RX,
+ DMACH_PCM0_TX,
+ DMACH_PCM1_RX,
+ DMACH_PCM1_TX,
+ DMACH_MSM_REQ0,
+ DMACH_MSM_REQ1,
+ DMACH_MSM_REQ2,
+ DMACH_MSM_REQ3,
+ DMACH_PCM2_RX,
+ DMACH_PCM2_TX,
};
struct dma_pl330_platdata s5pv210_pdma1_pdata = {
.nr_valid_peri = ARRAY_SIZE(pdma1_peri),
- .peri = pdma1_peri,
+ .peri_id = pdma1_peri,
};
struct amba_device s5pv210_device_pdma1 = {
static int __init s5pv210_dma_init(void)
{
+ dma_cap_set(DMA_SLAVE, s5pv210_pdma0_pdata.cap_mask);
+ dma_cap_set(DMA_CYCLIC, s5pv210_pdma0_pdata.cap_mask);
amba_device_register(&s5pv210_device_pdma0, &iomem_resource);
+
+ dma_cap_set(DMA_SLAVE, s5pv210_pdma1_pdata.cap_mask);
+ dma_cap_set(DMA_CYCLIC, s5pv210_pdma1_pdata.cap_mask);
amba_device_register(&s5pv210_device_pdma1, &iomem_resource);
return 0;
#define IRQ_MDNIE3 S5P_IRQ_VIC3(8)
#define IRQ_VIC_END S5P_IRQ_VIC3(31)
+#define IRQ_TIMER_BASE (11)
+
#define S5P_EINT_BASE1 (S5P_IRQ_VIC0(0))
#define S5P_EINT_BASE2 (IRQ_VIC_END + 1)
#define S3C_PA_RTC S5PV210_PA_RTC
#define S3C_PA_USB_HSOTG S5PV210_PA_HSOTG
#define S3C_PA_WDT S5PV210_PA_WATCHDOG
+#define S3C_PA_SPI0 S5PV210_PA_SPI0
+#define S3C_PA_SPI1 S5PV210_PA_SPI1
#define S5P_PA_CHIPID S5PV210_PA_CHIPID
#define S5P_PA_FIMC0 S5PV210_PA_FIMC0
#include <plat/s5pv210.h>
#include <plat/regs-serial.h>
-static struct s3c24xx_uart_clksrc s5pv210_serial_clocks[] = {
- [0] = {
- .name = "pclk",
- .divisor = 1,
- .min_baud = 0,
- .max_baud = 0,
- },
-};
-
/* uart registration process */
void __init s5pv210_common_init_uarts(struct s3c2410_uartcfg *cfg, int no)
{
- struct s3c2410_uartcfg *tcfg = cfg;
- u32 ucnt;
-
- for (ucnt = 0; ucnt < no; ucnt++, tcfg++) {
- if (!tcfg->clocks) {
- tcfg->clocks = s5pv210_serial_clocks;
- tcfg->clocks_size = ARRAY_SIZE(s5pv210_serial_clocks);
- }
- }
-
s3c24xx_init_uartdevs("s5pv210-uart", s5p_uart_resources, cfg, no);
}
+++ /dev/null
-/* linux/arch/arm/mach-s5pv210/setup-sdhci.c
- *
- * Copyright (c) 2009-2010 Samsung Electronics Co., Ltd.
- * http://www.samsung.com/
- *
- * S5PV210 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *s5pv210_hsmmc_clksrcs[4] = {
- [0] = "hsmmc", /* HCLK */
- /* [1] = "hsmmc", - duplicate HCLK entry */
- [2] = "sclk_mmc", /* mmc_bus */
- /* [3] = NULL, - reserved */
-};
--- /dev/null
+/* linux/arch/arm/mach-s5pv210/setup-spi.c
+ *
+ * Copyright (C) 2011 Samsung Electronics Ltd.
+ * http://www.samsung.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+
+#include <plat/gpio-cfg.h>
+#include <plat/s3c64xx-spi.h>
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+struct s3c64xx_spi_info s3c64xx_spi0_pdata = {
+ .fifo_lvl_mask = 0x1ff,
+ .rx_lvl_offset = 15,
+ .high_speed = 1,
+ .tx_st_done = 25,
+};
+
+int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+{
+ s3c_gpio_cfgpin(S5PV210_GPB(0), S3C_GPIO_SFN(2));
+ s3c_gpio_setpull(S5PV210_GPB(0), S3C_GPIO_PULL_UP);
+ s3c_gpio_cfgall_range(S5PV210_GPB(2), 2,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+struct s3c64xx_spi_info s3c64xx_spi1_pdata = {
+ .fifo_lvl_mask = 0x7f,
+ .rx_lvl_offset = 15,
+ .high_speed = 1,
+ .tx_st_done = 25,
+};
+
+int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+{
+ s3c_gpio_cfgpin(S5PV210_GPB(4), S3C_GPIO_SFN(2));
+ s3c_gpio_setpull(S5PV210_GPB(4), S3C_GPIO_PULL_UP);
+ s3c_gpio_cfgall_range(S5PV210_GPB(6), 2,
+ S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+ return 0;
+}
+#endif
static struct clksrc_clk clksrc_clks[] = {
{
- /* ART baud-rate clock sourced from esysclk via a divisor */
- .clk = {
- .name = "uartclk",
- .parent = &clk_esysclk.clk,
- },
- .reg_div = { .reg = S3C2443_CLKDIV1, .size = 4, .shift = 8 },
- }, {
/* camera interface bus-clock, divided down from esysclk */
.clk = {
.name = "camif-upll", /* same as 2440 name */
},
};
+static struct clksrc_clk clk_esys_uart = {
+ /* ART baud-rate clock sourced from esysclk via a divisor */
+ .clk = {
+ .name = "uartclk",
+ .parent = &clk_esysclk.clk,
+ },
+ .reg_div = { .reg = S3C2443_CLKDIV1, .size = 4, .shift = 8 },
+};
+
static struct clk clk_i2s_ext = {
.name = "i2s-ext",
};
.parent = &clk_h,
.enable = s3c2443_clkcon_enable_h,
.ctrlbit = S3C2443_HCLKCON_DMA5,
- }, {
- .name = "hsmmc",
- .devname = "s3c-sdhci.1",
- .parent = &clk_h,
- .enable = s3c2443_clkcon_enable_h,
- .ctrlbit = S3C2443_HCLKCON_HSMMC,
}, {
.name = "gpio",
.parent = &clk_p,
}
};
+static struct clk hsmmc1_clk = {
+ .name = "hsmmc",
+ .devname = "s3c-sdhci.1",
+ .parent = &clk_h,
+ .enable = s3c2443_clkcon_enable_h,
+ .ctrlbit = S3C2443_HCLKCON_HSMMC,
+};
+
static inline unsigned long s3c2443_get_hdiv(unsigned long clkcon0)
{
clkcon0 &= S3C2443_CLKDIV0_HCLKDIV_MASK;
&clk_epll,
&clk_usb_bus,
&clk_armdiv,
+ &hsmmc1_clk,
};
static struct clksrc_clk *clksrcs[] __initdata = {
&clk_arm,
};
+static struct clk_lookup s3c2443_clk_lookup[] = {
+ CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk),
+ CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
+ CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_esys_uart.clk),
+ CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &hsmmc1_clk),
+};
+
void __init s3c2443_common_init_clocks(int xtal, pll_fn get_mpll,
unsigned int *divs, int nr_divs,
int divmask)
/* See s3c2443/etc notes on disabling clocks at init time */
s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+ clkdev_add_table(s3c2443_clk_lookup, ARRAY_SIZE(s3c2443_clk_lookup));
s3c2443_common_setup_clocks(get_mpll);
}
help
Compile in platform device definitions for IDE
-config S3C64XX_DEV_SPI
+config S3C64XX_DEV_SPI0
bool
help
Compile in platform device definitions for S3C64XX's type
- SPI controllers.
+ SPI controller 0
+
+config S3C64XX_DEV_SPI1
+ bool
+ help
+ Compile in platform device definitions for S3C64XX's type
+ SPI controller 1
+
+config S3C64XX_DEV_SPI2
+ bool
+ help
+ Compile in platform device definitions for S3C64XX's type
+ SPI controller 2
config SAMSUNG_DEV_TS
bool
#include <plat/regs-iic.h>
#include <plat/regs-serial.h>
#include <plat/regs-spi.h>
+#include <plat/s3c64xx-spi.h>
static u64 samsung_device_dma_mask = DMA_BIT_MASK(32);
.resource = s3c_wdt_resource,
};
#endif /* CONFIG_S3C_DEV_WDT */
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+static struct resource s3c64xx_spi0_resource[] = {
+ [0] = DEFINE_RES_MEM(S3C_PA_SPI0, SZ_256),
+ [1] = DEFINE_RES_DMA(DMACH_SPI0_TX),
+ [2] = DEFINE_RES_DMA(DMACH_SPI0_RX),
+ [3] = DEFINE_RES_IRQ(IRQ_SPI0),
+};
+
+struct platform_device s3c64xx_device_spi0 = {
+ .name = "s3c64xx-spi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(s3c64xx_spi0_resource),
+ .resource = s3c64xx_spi0_resource,
+ .dev = {
+ .dma_mask = &samsung_device_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+
+void __init s3c64xx_spi0_set_platdata(struct s3c64xx_spi_info *pd,
+ int src_clk_nr, int num_cs)
+{
+ if (!pd) {
+ pr_err("%s:Need to pass platform data\n", __func__);
+ return;
+ }
+
+ /* Reject invalid configuration */
+ if (!num_cs || src_clk_nr < 0) {
+ pr_err("%s: Invalid SPI configuration\n", __func__);
+ return;
+ }
+
+ pd->num_cs = num_cs;
+ pd->src_clk_nr = src_clk_nr;
+ if (!pd->cfg_gpio)
+ pd->cfg_gpio = s3c64xx_spi0_cfg_gpio;
+
+ s3c_set_platdata(pd, sizeof(*pd), &s3c64xx_device_spi0);
+}
+#endif /* CONFIG_S3C64XX_DEV_SPI0 */
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+static struct resource s3c64xx_spi1_resource[] = {
+ [0] = DEFINE_RES_MEM(S3C_PA_SPI1, SZ_256),
+ [1] = DEFINE_RES_DMA(DMACH_SPI1_TX),
+ [2] = DEFINE_RES_DMA(DMACH_SPI1_RX),
+ [3] = DEFINE_RES_IRQ(IRQ_SPI1),
+};
+
+struct platform_device s3c64xx_device_spi1 = {
+ .name = "s3c64xx-spi",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(s3c64xx_spi1_resource),
+ .resource = s3c64xx_spi1_resource,
+ .dev = {
+ .dma_mask = &samsung_device_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+
+void __init s3c64xx_spi1_set_platdata(struct s3c64xx_spi_info *pd,
+ int src_clk_nr, int num_cs)
+{
+ if (!pd) {
+ pr_err("%s:Need to pass platform data\n", __func__);
+ return;
+ }
+
+ /* Reject invalid configuration */
+ if (!num_cs || src_clk_nr < 0) {
+ pr_err("%s: Invalid SPI configuration\n", __func__);
+ return;
+ }
+
+ pd->num_cs = num_cs;
+ pd->src_clk_nr = src_clk_nr;
+ if (!pd->cfg_gpio)
+ pd->cfg_gpio = s3c64xx_spi1_cfg_gpio;
+
+ s3c_set_platdata(pd, sizeof(*pd), &s3c64xx_device_spi1);
+}
+#endif /* CONFIG_S3C64XX_DEV_SPI1 */
+
+#ifdef CONFIG_S3C64XX_DEV_SPI2
+static struct resource s3c64xx_spi2_resource[] = {
+ [0] = DEFINE_RES_MEM(S3C_PA_SPI2, SZ_256),
+ [1] = DEFINE_RES_DMA(DMACH_SPI2_TX),
+ [2] = DEFINE_RES_DMA(DMACH_SPI2_RX),
+ [3] = DEFINE_RES_IRQ(IRQ_SPI2),
+};
+
+struct platform_device s3c64xx_device_spi2 = {
+ .name = "s3c64xx-spi",
+ .id = 2,
+ .num_resources = ARRAY_SIZE(s3c64xx_spi2_resource),
+ .resource = s3c64xx_spi2_resource,
+ .dev = {
+ .dma_mask = &samsung_device_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+
+void __init s3c64xx_spi2_set_platdata(struct s3c64xx_spi_info *pd,
+ int src_clk_nr, int num_cs)
+{
+ if (!pd) {
+ pr_err("%s:Need to pass platform data\n", __func__);
+ return;
+ }
+
+ /* Reject invalid configuration */
+ if (!num_cs || src_clk_nr < 0) {
+ pr_err("%s: Invalid SPI configuration\n", __func__);
+ return;
+ }
+
+ pd->num_cs = num_cs;
+ pd->src_clk_nr = src_clk_nr;
+ if (!pd->cfg_gpio)
+ pd->cfg_gpio = s3c64xx_spi2_cfg_gpio;
+
+ s3c_set_platdata(pd, sizeof(*pd), &s3c64xx_device_spi2);
+}
+#endif /* CONFIG_S3C64XX_DEV_SPI2 */
#include <mach/dma.h>
-static inline bool pl330_filter(struct dma_chan *chan, void *param)
-{
- struct dma_pl330_peri *peri = chan->private;
- return peri->peri_id == (unsigned)param;
-}
-
static unsigned samsung_dmadev_request(enum dma_ch dma_ch,
struct samsung_dma_info *info)
{
struct dma_chan *chan;
dma_cap_mask_t mask;
struct dma_slave_config slave_config;
+ void *filter_param;
dma_cap_zero(mask);
dma_cap_set(info->cap, mask);
- chan = dma_request_channel(mask, pl330_filter, (void *)dma_ch);
+ /*
+ * If a dma channel property of a device node from device tree is
+ * specified, use that as the fliter parameter.
+ */
+ filter_param = (dma_ch == DMACH_DT_PROP) ? (void *)info->dt_dmach_prop :
+ (void *)dma_ch;
+ chan = dma_request_channel(mask, pl330_filter, filter_param);
if (info->direction == DMA_FROM_DEVICE) {
memset(&slave_config, 0, sizeof(struct dma_slave_config));
extern struct platform_device s3c64xx_device_pcm1;
extern struct platform_device s3c64xx_device_spi0;
extern struct platform_device s3c64xx_device_spi1;
+extern struct platform_device s3c64xx_device_spi2;
extern struct platform_device s3c_device_adc;
extern struct platform_device s3c_device_cfcon;
extern struct platform_device s5p6450_device_iis2;
extern struct platform_device s5p6450_device_pcm0;
-extern struct platform_device s5p64x0_device_spi0;
-extern struct platform_device s5p64x0_device_spi1;
extern struct platform_device s5pc100_device_ac97;
extern struct platform_device s5pc100_device_iis0;
extern struct platform_device s5pc100_device_pcm0;
extern struct platform_device s5pc100_device_pcm1;
extern struct platform_device s5pc100_device_spdif;
-extern struct platform_device s5pc100_device_spi0;
-extern struct platform_device s5pc100_device_spi1;
-extern struct platform_device s5pc100_device_spi2;
extern struct platform_device s5pv210_device_ac97;
extern struct platform_device s5pv210_device_iis0;
extern struct platform_device s5pv210_device_pcm1;
extern struct platform_device s5pv210_device_pcm2;
extern struct platform_device s5pv210_device_spdif;
-extern struct platform_device s5pv210_device_spi0;
-extern struct platform_device s5pv210_device_spi1;
extern struct platform_device exynos4_device_ac97;
extern struct platform_device exynos4_device_ahci;
enum dma_slave_buswidth width;
dma_addr_t fifo;
struct s3c2410_dma_client *client;
+ struct property *dt_dmach_prop;
};
struct samsung_dma_ops {
* use these just as IDs.
*/
enum dma_ch {
- DMACH_UART0_RX,
+ DMACH_DT_PROP = -1,
+ DMACH_UART0_RX = 0,
DMACH_UART0_TX,
DMACH_UART1_RX,
DMACH_UART1_TX,
#define S5P_IRQ_VIC2(x) (S5P_VIC2_BASE + (x))
#define S5P_IRQ_VIC3(x) (S5P_VIC3_BASE + (x))
-#define S5P_TIMER_IRQ(x) (11 + (x))
+#define S5P_TIMER_IRQ(x) (IRQ_TIMER_BASE + (x))
#define IRQ_TIMER0 S5P_TIMER_IRQ(0)
#define IRQ_TIMER1 S5P_TIMER_IRQ(1)
#define IRQ_TIMER2 S5P_TIMER_IRQ(2)
#define IRQ_TIMER3 S5P_TIMER_IRQ(3)
#define IRQ_TIMER4 S5P_TIMER_IRQ(4)
+#define IRQ_TIMER_COUNT (5)
#define IRQ_EINT(x) ((x) < 16 ? ((x) + S5P_EINT_BASE1) \
: ((x) - 16 + S5P_EINT_BASE2))
#define S3C2410_LCON_IRM (1<<6)
#define S3C2440_UCON_CLKMASK (3<<10)
+#define S3C2440_UCON_CLKSHIFT (10)
#define S3C2440_UCON_PCLK (0<<10)
#define S3C2440_UCON_UCLK (1<<10)
#define S3C2440_UCON_PCLK2 (2<<10)
#define S3C2443_UCON_EPLL (3<<10)
#define S3C6400_UCON_CLKMASK (3<<10)
+#define S3C6400_UCON_CLKSHIFT (10)
#define S3C6400_UCON_PCLK (0<<10)
#define S3C6400_UCON_PCLK2 (2<<10)
#define S3C6400_UCON_UCLK0 (1<<10)
#define S3C2440_UCON_DIVSHIFT (12)
#define S3C2412_UCON_CLKMASK (3<<10)
+#define S3C2412_UCON_CLKSHIFT (10)
#define S3C2412_UCON_UCLK (1<<10)
#define S3C2412_UCON_USYSCLK (3<<10)
#define S3C2412_UCON_PCLK (0<<10)
#define S3C2412_UCON_PCLK2 (2<<10)
+#define S3C2410_UCON_CLKMASK (1 << 10)
+#define S3C2410_UCON_CLKSHIFT (10)
#define S3C2410_UCON_UCLK (1<<10)
#define S3C2410_UCON_SBREAK (1<<4)
/* Following are specific to S5PV210 */
#define S5PV210_UCON_CLKMASK (1<<10)
+#define S5PV210_UCON_CLKSHIFT (10)
#define S5PV210_UCON_PCLK (0<<10)
#define S5PV210_UCON_UCLK (1<<10)
#define S5PV210_UFSTAT_RXMASK (255<<0)
#define S5PV210_UFSTAT_RXSHIFT (0)
-#define NO_NEED_CHECK_CLKSRC 1
+#define S3C2410_UCON_CLKSEL0 (1 << 0)
+#define S3C2410_UCON_CLKSEL1 (1 << 1)
+#define S3C2410_UCON_CLKSEL2 (1 << 2)
+#define S3C2410_UCON_CLKSEL3 (1 << 3)
-#ifndef __ASSEMBLY__
+/* Default values for s5pv210 UCON and UFCON uart registers */
+#define S5PV210_UCON_DEFAULT (S3C2410_UCON_TXILEVEL | \
+ S3C2410_UCON_RXILEVEL | \
+ S3C2410_UCON_TXIRQMODE | \
+ S3C2410_UCON_RXIRQMODE | \
+ S3C2410_UCON_RXFIFO_TOI | \
+ S3C2443_UCON_RXERR_IRQEN)
-/* struct s3c24xx_uart_clksrc
- *
- * this structure defines a named clock source that can be used for the
- * uart, so that the best clock can be selected for the requested baud
- * rate.
- *
- * min_baud and max_baud define the range of baud-rates this clock is
- * acceptable for, if they are both zero, it is assumed any baud rate that
- * can be generated from this clock will be used.
- *
- * divisor gives the divisor from the clock to the one seen by the uart
-*/
+#define S5PV210_UFCON_DEFAULT (S3C2410_UFCON_FIFOMODE | \
+ S5PV210_UFCON_TXTRIG4 | \
+ S5PV210_UFCON_RXTRIG4)
-struct s3c24xx_uart_clksrc {
- const char *name;
- unsigned int divisor;
- unsigned int min_baud;
- unsigned int max_baud;
-};
+#ifndef __ASSEMBLY__
/* configuration structure for per-machine configurations for the
* serial port
unsigned char unused;
unsigned short flags;
upf_t uart_flags; /* default uart flags */
+ unsigned int clk_sel;
unsigned int has_fracval;
unsigned long ucon; /* value of ucon for port */
unsigned long ulcon; /* value of ulcon for port */
unsigned long ufcon; /* value of ufcon for port */
-
- struct s3c24xx_uart_clksrc *clocks;
- unsigned int clocks_size;
};
/* s3c24xx_uart_devs
/**
* struct s3c64xx_spi_info - SPI Controller defining structure
* @src_clk_nr: Clock source index for the CLK_CFG[SPI_CLKSEL] field.
- * @src_clk_name: Platform name of the corresponding clock.
* @clk_from_cmu: If the SPI clock/prescalar control block is present
* by the platform's clock-management-unit and not in SPI controller.
* @num_cs: Number of CS this controller emulates.
*/
struct s3c64xx_spi_info {
int src_clk_nr;
- char *src_clk_name;
bool clk_from_cmu;
int num_cs;
};
/**
- * s3c64xx_spi_set_info - SPI Controller configure callback by the board
+ * s3c64xx_spi_set_platdata - SPI Controller configure callback by the board
* initialization code.
- * @cntrlr: SPI controller number the configuration is for.
+ * @pd: SPI platform data to set.
* @src_clk_nr: Clock the SPI controller is to use to generate SPI clocks.
* @num_cs: Number of elements in the 'cs' array.
*
* Call this from machine init code for each SPI Controller that
* has some chips attached to it.
*/
-extern void s3c64xx_spi_set_info(int cntrlr, int src_clk_nr, int num_cs);
-extern void s5pc100_spi_set_info(int cntrlr, int src_clk_nr, int num_cs);
-extern void s5pv210_spi_set_info(int cntrlr, int src_clk_nr, int num_cs);
-extern void s5p64x0_spi_set_info(int cntrlr, int src_clk_nr, int num_cs);
+extern void s3c64xx_spi0_set_platdata(struct s3c64xx_spi_info *pd,
+ int src_clk_nr, int num_cs);
+extern void s3c64xx_spi1_set_platdata(struct s3c64xx_spi_info *pd,
+ int src_clk_nr, int num_cs);
+extern void s3c64xx_spi2_set_platdata(struct s3c64xx_spi_info *pd,
+ int src_clk_nr, int num_cs);
+/* defined by architecture to configure gpio */
+extern int s3c64xx_spi0_cfg_gpio(struct platform_device *dev);
+extern int s3c64xx_spi1_cfg_gpio(struct platform_device *dev);
+extern int s3c64xx_spi2_cfg_gpio(struct platform_device *dev);
+
+extern struct s3c64xx_spi_info s3c64xx_spi0_pdata;
+extern struct s3c64xx_spi_info s3c64xx_spi1_pdata;
+extern struct s3c64xx_spi_info s3c64xx_spi2_pdata;
#endif /* __S3C64XX_PLAT_SPI_H */
enum cd_types cd_type;
enum clk_types clk_type;
- char **clocks; /* set of clock sources */
-
int ext_cd_gpio;
bool ext_cd_gpio_invert;
int (*ext_cd_init)(void (*notify_func)(struct platform_device *,
/* S3C2416 SDHCI setup */
#ifdef CONFIG_S3C2416_SETUP_SDHCI
-extern char *s3c2416_hsmmc_clksrcs[4];
-
static inline void s3c2416_default_sdhci0(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC
- s3c_hsmmc0_def_platdata.clocks = s3c2416_hsmmc_clksrcs;
s3c_hsmmc0_def_platdata.cfg_gpio = s3c2416_setup_sdhci0_cfg_gpio;
#endif /* CONFIG_S3C_DEV_HSMMC */
}
static inline void s3c2416_default_sdhci1(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC1
- s3c_hsmmc1_def_platdata.clocks = s3c2416_hsmmc_clksrcs;
s3c_hsmmc1_def_platdata.cfg_gpio = s3c2416_setup_sdhci1_cfg_gpio;
#endif /* CONFIG_S3C_DEV_HSMMC1 */
}
/* S3C64XX SDHCI setup */
#ifdef CONFIG_S3C64XX_SETUP_SDHCI
-extern char *s3c64xx_hsmmc_clksrcs[4];
-
static inline void s3c6400_default_sdhci0(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC
- s3c_hsmmc0_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
#endif
}
static inline void s3c6400_default_sdhci1(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC1
- s3c_hsmmc1_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
#endif
}
static inline void s3c6400_default_sdhci2(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC2
- s3c_hsmmc2_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
s3c_hsmmc2_def_platdata.cfg_gpio = s3c64xx_setup_sdhci2_cfg_gpio;
#endif
}
static inline void s3c6410_default_sdhci0(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC
- s3c_hsmmc0_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
#endif
}
static inline void s3c6410_default_sdhci1(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC1
- s3c_hsmmc1_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
#endif
}
static inline void s3c6410_default_sdhci2(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC2
- s3c_hsmmc2_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
s3c_hsmmc2_def_platdata.cfg_gpio = s3c64xx_setup_sdhci2_cfg_gpio;
#endif
}
/* S5PC100 SDHCI setup */
#ifdef CONFIG_S5PC100_SETUP_SDHCI
-extern char *s5pc100_hsmmc_clksrcs[4];
-
static inline void s5pc100_default_sdhci0(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC
- s3c_hsmmc0_def_platdata.clocks = s5pc100_hsmmc_clksrcs;
s3c_hsmmc0_def_platdata.cfg_gpio = s5pc100_setup_sdhci0_cfg_gpio;
#endif
}
static inline void s5pc100_default_sdhci1(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC1
- s3c_hsmmc1_def_platdata.clocks = s5pc100_hsmmc_clksrcs;
s3c_hsmmc1_def_platdata.cfg_gpio = s5pc100_setup_sdhci1_cfg_gpio;
#endif
}
static inline void s5pc100_default_sdhci2(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC2
- s3c_hsmmc2_def_platdata.clocks = s5pc100_hsmmc_clksrcs;
s3c_hsmmc2_def_platdata.cfg_gpio = s5pc100_setup_sdhci2_cfg_gpio;
#endif
}
/* S5PV210 SDHCI setup */
#ifdef CONFIG_S5PV210_SETUP_SDHCI
-extern char *s5pv210_hsmmc_clksrcs[4];
-
static inline void s5pv210_default_sdhci0(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC
- s3c_hsmmc0_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
s3c_hsmmc0_def_platdata.cfg_gpio = s5pv210_setup_sdhci0_cfg_gpio;
#endif
}
static inline void s5pv210_default_sdhci1(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC1
- s3c_hsmmc1_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
s3c_hsmmc1_def_platdata.cfg_gpio = s5pv210_setup_sdhci1_cfg_gpio;
#endif
}
static inline void s5pv210_default_sdhci2(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC2
- s3c_hsmmc2_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
s3c_hsmmc2_def_platdata.cfg_gpio = s5pv210_setup_sdhci2_cfg_gpio;
#endif
}
static inline void s5pv210_default_sdhci3(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC3
- s3c_hsmmc3_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
s3c_hsmmc3_def_platdata.cfg_gpio = s5pv210_setup_sdhci3_cfg_gpio;
#endif
}
/* EXYNOS4 SDHCI setup */
#ifdef CONFIG_EXYNOS4_SETUP_SDHCI
-extern char *exynos4_hsmmc_clksrcs[4];
-
static inline void exynos4_default_sdhci0(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC
- s3c_hsmmc0_def_platdata.clocks = exynos4_hsmmc_clksrcs;
s3c_hsmmc0_def_platdata.cfg_gpio = exynos4_setup_sdhci0_cfg_gpio;
#endif
}
static inline void exynos4_default_sdhci1(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC1
- s3c_hsmmc1_def_platdata.clocks = exynos4_hsmmc_clksrcs;
s3c_hsmmc1_def_platdata.cfg_gpio = exynos4_setup_sdhci1_cfg_gpio;
#endif
}
static inline void exynos4_default_sdhci2(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC2
- s3c_hsmmc2_def_platdata.clocks = exynos4_hsmmc_clksrcs;
s3c_hsmmc2_def_platdata.cfg_gpio = exynos4_setup_sdhci2_cfg_gpio;
#endif
}
static inline void exynos4_default_sdhci3(void)
{
#ifdef CONFIG_S3C_DEV_HSMMC3
- s3c_hsmmc3_def_platdata.clocks = exynos4_hsmmc_clksrcs;
s3c_hsmmc3_def_platdata.cfg_gpio = exynos4_setup_sdhci3_cfg_gpio;
#endif
}
#include <linux/amba/pl330.h>
#include <linux/pm_runtime.h>
#include <linux/scatterlist.h>
+#include <linux/of.h>
#define NR_DEFAULT_DESC 16
struct dma_pl330_chan *pchan;
};
+/* forward declaration */
+static struct amba_driver pl330_driver;
+
static inline struct dma_pl330_chan *
to_pchan(struct dma_chan *ch)
{
tasklet_schedule(&pch->task);
}
+bool pl330_filter(struct dma_chan *chan, void *param)
+{
+ u8 *peri_id;
+
+ if (chan->device->dev->driver != &pl330_driver.drv)
+ return false;
+
+#ifdef CONFIG_OF
+ if (chan->device->dev->of_node) {
+ const __be32 *prop_value;
+ phandle phandle;
+ struct device_node *node;
+
+ prop_value = ((struct property *)param)->value;
+ phandle = be32_to_cpup(prop_value++);
+ node = of_find_node_by_phandle(phandle);
+ return ((chan->private == node) &&
+ (chan->chan_id == be32_to_cpup(prop_value)));
+ }
+#endif
+
+ peri_id = chan->private;
+ return *peri_id == (unsigned)param;
+}
+EXPORT_SYMBOL(pl330_filter);
+
static int pl330_alloc_chan_resources(struct dma_chan *chan)
{
struct dma_pl330_chan *pch = to_pchan(chan);
static struct dma_pl330_desc *pl330_get_desc(struct dma_pl330_chan *pch)
{
struct dma_pl330_dmac *pdmac = pch->dmac;
- struct dma_pl330_peri *peri = pch->chan.private;
+ u8 *peri_id = pch->chan.private;
struct dma_pl330_desc *desc;
/* Pluck one desc from the pool of DMAC */
desc->txd.cookie = 0;
async_tx_ack(&desc->txd);
- if (peri) {
- desc->req.rqtype = peri->rqtype;
- desc->req.peri = pch->chan.chan_id;
- } else {
- desc->req.rqtype = MEMTOMEM;
- desc->req.peri = 0;
- }
+ desc->req.peri = peri_id ? pch->chan.chan_id : 0;
dma_async_tx_descriptor_init(&desc->txd, &pch->chan);
case DMA_TO_DEVICE:
desc->rqcfg.src_inc = 1;
desc->rqcfg.dst_inc = 0;
+ desc->req.rqtype = MEMTODEV;
src = dma_addr;
dst = pch->fifo_addr;
break;
case DMA_FROM_DEVICE:
desc->rqcfg.src_inc = 0;
desc->rqcfg.dst_inc = 1;
+ desc->req.rqtype = DEVTOMEM;
src = pch->fifo_addr;
dst = dma_addr;
break;
{
struct dma_pl330_desc *desc;
struct dma_pl330_chan *pch = to_pchan(chan);
- struct dma_pl330_peri *peri = chan->private;
struct pl330_info *pi;
int burst;
if (unlikely(!pch || !len))
return NULL;
- if (peri && peri->rqtype != MEMTOMEM)
- return NULL;
-
pi = &pch->dmac->pif;
desc = __pl330_prep_dma_memcpy(pch, dst, src, len);
desc->rqcfg.src_inc = 1;
desc->rqcfg.dst_inc = 1;
+ desc->req.rqtype = MEMTOMEM;
/* Select max possible burst size */
burst = pi->pcfg.data_bus_width / 8;
{
struct dma_pl330_desc *first, *desc = NULL;
struct dma_pl330_chan *pch = to_pchan(chan);
- struct dma_pl330_peri *peri = chan->private;
struct scatterlist *sg;
unsigned long flags;
int i;
dma_addr_t addr;
- if (unlikely(!pch || !sgl || !sg_len || !peri))
+ if (unlikely(!pch || !sgl || !sg_len))
return NULL;
- /* Make sure the direction is consistent */
- if ((direction == DMA_TO_DEVICE &&
- peri->rqtype != MEMTODEV) ||
- (direction == DMA_FROM_DEVICE &&
- peri->rqtype != DEVTOMEM)) {
- dev_err(pch->dmac->pif.dev, "%s:%d Invalid Direction\n",
- __func__, __LINE__);
- return NULL;
- }
-
addr = pch->fifo_addr;
first = NULL;
if (direction == DMA_TO_DEVICE) {
desc->rqcfg.src_inc = 1;
desc->rqcfg.dst_inc = 0;
+ desc->req.rqtype = MEMTODEV;
fill_px(&desc->px,
addr, sg_dma_address(sg), sg_dma_len(sg));
} else {
desc->rqcfg.src_inc = 0;
desc->rqcfg.dst_inc = 1;
+ desc->req.rqtype = DEVTOMEM;
fill_px(&desc->px,
sg_dma_address(sg), addr, sg_dma_len(sg));
}
INIT_LIST_HEAD(&pd->channels);
/* Initialize channel parameters */
- num_chan = max(pdat ? pdat->nr_valid_peri : 0, (u8)pi->pcfg.num_chan);
+ num_chan = max(pdat ? pdat->nr_valid_peri : (u8)pi->pcfg.num_peri,
+ (u8)pi->pcfg.num_chan);
pdmac->peripherals = kzalloc(num_chan * sizeof(*pch), GFP_KERNEL);
for (i = 0; i < num_chan; i++) {
pch = &pdmac->peripherals[i];
- if (pdat) {
- struct dma_pl330_peri *peri = &pdat->peri[i];
-
- switch (peri->rqtype) {
- case MEMTOMEM:
- dma_cap_set(DMA_MEMCPY, pd->cap_mask);
- break;
- case MEMTODEV:
- case DEVTOMEM:
- dma_cap_set(DMA_SLAVE, pd->cap_mask);
- dma_cap_set(DMA_CYCLIC, pd->cap_mask);
- break;
- default:
- dev_err(&adev->dev, "DEVTODEV Not Supported\n");
- continue;
- }
- pch->chan.private = peri;
- } else {
- dma_cap_set(DMA_MEMCPY, pd->cap_mask);
- pch->chan.private = NULL;
- }
+ if (!adev->dev.of_node)
+ pch->chan.private = pdat ? &pdat->peri_id[i] : NULL;
+ else
+ pch->chan.private = adev->dev.of_node;
INIT_LIST_HEAD(&pch->work_list);
spin_lock_init(&pch->lock);
}
pd->dev = &adev->dev;
+ if (pdat) {
+ pd->cap_mask = pdat->cap_mask;
+ } else {
+ dma_cap_set(DMA_MEMCPY, pd->cap_mask);
+ if (pi->pcfg.num_peri) {
+ dma_cap_set(DMA_SLAVE, pd->cap_mask);
+ dma_cap_set(DMA_CYCLIC, pd->cap_mask);
+ }
+ }
pd->device_alloc_chan_resources = pl330_alloc_chan_resources;
pd->device_free_chan_resources = pl330_free_chan_resources;
#include <linux/interrupt.h>
#include <linux/sysdev.h>
#include <linux/ioport.h>
+#include <linux/of.h>
+#include <linux/slab.h>
+#include <linux/of_address.h>
#include <asm/irq.h>
#endif
};
+#if defined(CONFIG_ARCH_EXYNOS4) && defined(CONFIG_OF)
+static int exynos4_gpio_xlate(struct gpio_chip *gc, struct device_node *np,
+ const void *gpio_spec, u32 *flags)
+{
+ const __be32 *gpio = gpio_spec;
+ const u32 n = be32_to_cpup(gpio);
+ unsigned int pin = gc->base + be32_to_cpu(gpio[0]);
+
+ if (WARN_ON(gc->of_gpio_n_cells < 4))
+ return -EINVAL;
+
+ if (n > gc->ngpio)
+ return -EINVAL;
+
+ if (s3c_gpio_cfgpin(pin, S3C_GPIO_SFN(be32_to_cpu(gpio[1]))))
+ pr_warn("gpio_xlate: failed to set pin function\n");
+ if (s3c_gpio_setpull(pin, be32_to_cpu(gpio[2])))
+ pr_warn("gpio_xlate: failed to set pin pull up/down\n");
+ if (s5p_gpio_set_drvstr(pin, be32_to_cpu(gpio[3])))
+ pr_warn("gpio_xlate: failed to set pin drive strength\n");
+
+ return n;
+}
+
+static const struct of_device_id exynos4_gpio_dt_match[] __initdata = {
+ { .compatible = "samsung,exynos4-gpio", },
+ {}
+};
+
+static __init void exynos4_gpiolib_attach_ofnode(struct samsung_gpio_chip *chip,
+ u64 base, u64 offset)
+{
+ struct gpio_chip *gc = &chip->chip;
+ u64 address;
+
+ if (!of_have_populated_dt())
+ return;
+
+ address = chip->base ? base + ((u32)chip->base & 0xfff) : base + offset;
+ gc->of_node = of_find_matching_node_by_address(NULL,
+ exynos4_gpio_dt_match, address);
+ if (!gc->of_node) {
+ pr_info("gpio: device tree node not found for gpio controller"
+ " with base address %08llx\n", address);
+ return;
+ }
+ gc->of_gpio_n_cells = 4;
+ gc->of_xlate = exynos4_gpio_xlate;
+}
+#elif defined(CONFIG_ARCH_EXYNOS4)
+static __init void exynos4_gpiolib_attach_ofnode(struct samsung_gpio_chip *chip,
+ u64 base, u64 offset)
+{
+ return;
+}
+#endif /* defined(CONFIG_ARCH_EXYNOS4) && defined(CONFIG_OF) */
+
/* TODO: cleanup soc_is_* */
static __init int samsung_gpiolib_init(void)
{
chip->config = &exynos4_gpio_cfg;
chip->group = group++;
}
+#ifdef CONFIG_CPU_EXYNOS4210
+ exynos4_gpiolib_attach_ofnode(chip,
+ EXYNOS4_PA_GPIO1, i * 0x20);
+#endif
}
samsung_gpiolib_add_4bit_chips(exynos4_gpios_1, nr_chips, S5P_VA_GPIO1);
chip->config = &exynos4_gpio_cfg;
chip->group = group++;
}
+#ifdef CONFIG_CPU_EXYNOS4210
+ exynos4_gpiolib_attach_ofnode(chip,
+ EXYNOS4_PA_GPIO2, i * 0x20);
+#endif
}
samsung_gpiolib_add_4bit_chips(exynos4_gpios_2, nr_chips, S5P_VA_GPIO2);
chip->config = &exynos4_gpio_cfg;
chip->group = group++;
}
+#ifdef CONFIG_CPU_EXYNOS4210
+ exynos4_gpiolib_attach_ofnode(chip,
+ EXYNOS4_PA_GPIO3, i * 0x20);
+#endif
}
samsung_gpiolib_add_4bit_chips(exynos4_gpios_3, nr_chips, S5P_VA_GPIO3);
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
#include <linux/sched.h>
#include <plat/keypad.h>
wait_queue_head_t wait;
bool stopped;
int irq;
+ enum samsung_keypad_type type;
unsigned int row_shift;
unsigned int rows;
unsigned int cols;
unsigned int row_state[SAMSUNG_MAX_COLS];
+#ifdef CONFIG_OF
+ int row_gpios[SAMSUNG_MAX_ROWS];
+ int col_gpios[SAMSUNG_MAX_COLS];
+#endif
unsigned short keycodes[];
};
-static int samsung_keypad_is_s5pv210(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- enum samsung_keypad_type type =
- platform_get_device_id(pdev)->driver_data;
-
- return type == KEYPAD_TYPE_S5PV210;
-}
-
static void samsung_keypad_scan(struct samsung_keypad *keypad,
unsigned int *row_state)
{
- struct device *dev = keypad->input_dev->dev.parent;
unsigned int col;
unsigned int val;
for (col = 0; col < keypad->cols; col++) {
- if (samsung_keypad_is_s5pv210(dev)) {
+ if (keypad->type == KEYPAD_TYPE_S5PV210) {
val = S5PV210_KEYIFCOLEN_MASK;
val &= ~(1 << col) << 8;
} else {
samsung_keypad_stop(keypad);
}
+#ifdef CONFIG_OF
+static struct samsung_keypad_platdata *samsung_keypad_parse_dt(
+ struct device *dev)
+{
+ struct samsung_keypad_platdata *pdata;
+ struct matrix_keymap_data *keymap_data;
+ uint32_t *keymap, num_rows = 0, num_cols = 0;
+ struct device_node *np = dev->of_node, *key_np;
+ unsigned int key_count = 0;
+
+ pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata) {
+ dev_err(dev, "could not allocate memory for platform data\n");
+ return NULL;
+ }
+
+ of_property_read_u32(np, "samsung,keypad-num-rows", &num_rows);
+ of_property_read_u32(np, "samsung,keypad-num-columns", &num_cols);
+ if (!num_rows || !num_cols) {
+ dev_err(dev, "number of keypad rows/columns not specified\n");
+ return NULL;
+ }
+ pdata->rows = num_rows;
+ pdata->cols = num_cols;
+
+ keymap_data = devm_kzalloc(dev, sizeof(*keymap_data), GFP_KERNEL);
+ if (!keymap_data) {
+ dev_err(dev, "could not allocate memory for keymap data\n");
+ return NULL;
+ }
+ pdata->keymap_data = keymap_data;
+
+ for_each_child_of_node(np, key_np)
+ key_count++;
+
+ keymap_data->keymap_size = key_count;
+ keymap = devm_kzalloc(dev, sizeof(uint32_t) * key_count, GFP_KERNEL);
+ if (!keymap) {
+ dev_err(dev, "could not allocate memory for keymap\n");
+ return NULL;
+ }
+ keymap_data->keymap = keymap;
+
+ for_each_child_of_node(np, key_np) {
+ u32 row, col, key_code;
+ of_property_read_u32(key_np, "keypad,row", &row);
+ of_property_read_u32(key_np, "keypad,column", &col);
+ of_property_read_u32(key_np, "linux,code", &key_code);
+ *keymap++ = KEY(row, col, key_code);
+ }
+
+ if (of_get_property(np, "linux,input-no-autorepeat", NULL))
+ pdata->no_autorepeat = true;
+ if (of_get_property(np, "linux,input-wakeup", NULL))
+ pdata->wakeup = true;
+
+ return pdata;
+}
+
+static void samsung_keypad_parse_dt_gpio(struct device *dev,
+ struct samsung_keypad *keypad)
+{
+ struct device_node *np = dev->of_node;
+ int gpio, ret, row, col;
+
+ for (row = 0; row < keypad->rows; row++) {
+ gpio = of_get_named_gpio(np, "row-gpios", row);
+ keypad->row_gpios[row] = gpio;
+ if (!gpio_is_valid(gpio)) {
+ dev_err(dev, "keypad row[%d]: invalid gpio %d\n",
+ row, gpio);
+ continue;
+ }
+
+ ret = gpio_request(gpio, "keypad-row");
+ if (ret)
+ dev_err(dev, "keypad row[%d] gpio request failed\n",
+ row);
+ }
+
+ for (col = 0; col < keypad->cols; col++) {
+ gpio = of_get_named_gpio(np, "col-gpios", col);
+ keypad->col_gpios[col] = gpio;
+ if (!gpio_is_valid(gpio)) {
+ dev_err(dev, "keypad column[%d]: invalid gpio %d\n",
+ col, gpio);
+ continue;
+ }
+
+ ret = gpio_request(gpio, "keypad-col");
+ if (ret)
+ dev_err(dev, "keypad column[%d] gpio request failed\n",
+ col);
+ }
+}
+
+static void samsung_keypad_dt_gpio_free(struct samsung_keypad *keypad)
+{
+ int cnt;
+
+ for (cnt = 0; cnt < keypad->rows; cnt++)
+ if (gpio_is_valid(keypad->row_gpios[cnt]))
+ gpio_free(keypad->row_gpios[cnt]);
+
+ for (cnt = 0; cnt < keypad->cols; cnt++)
+ if (gpio_is_valid(keypad->col_gpios[cnt]))
+ gpio_free(keypad->col_gpios[cnt]);
+}
+#else
+static
+struct samsung_keypad_platdata *samsung_keypad_parse_dt(struct device *dev)
+{
+ return NULL;
+}
+
+static void samsung_keypad_dt_gpio_free(struct samsung_keypad *keypad)
+{
+}
+#endif
+
static int __devinit samsung_keypad_probe(struct platform_device *pdev)
{
const struct samsung_keypad_platdata *pdata;
unsigned int keymap_size;
int error;
- pdata = pdev->dev.platform_data;
+ if (pdev->dev.of_node)
+ pdata = samsung_keypad_parse_dt(&pdev->dev);
+ else
+ pdata = pdev->dev.platform_data;
if (!pdata) {
dev_err(&pdev->dev, "no platform data defined\n");
return -EINVAL;
keypad->cols = pdata->cols;
init_waitqueue_head(&keypad->wait);
+ if (pdev->dev.of_node) {
+#ifdef CONFIG_OF
+ samsung_keypad_parse_dt_gpio(&pdev->dev, keypad);
+ keypad->type = of_device_is_compatible(pdev->dev.of_node,
+ "samsung,s5pv210-keypad");
+#endif
+ } else {
+ keypad->type = platform_get_device_id(pdev)->driver_data;
+ }
+
input_dev->name = pdev->name;
input_dev->id.bustype = BUS_HOST;
input_dev->dev.parent = &pdev->dev;
device_init_wakeup(&pdev->dev, pdata->wakeup);
platform_set_drvdata(pdev, keypad);
+
+ if (pdev->dev.of_node) {
+ devm_kfree(&pdev->dev, (void *)pdata->keymap_data->keymap);
+ devm_kfree(&pdev->dev, (void *)pdata->keymap_data);
+ devm_kfree(&pdev->dev, (void *)pdata);
+ }
return 0;
err_free_irq:
free_irq(keypad->irq, keypad);
err_put_clk:
clk_put(keypad->clk);
+ samsung_keypad_dt_gpio_free(keypad);
err_unmap_base:
iounmap(keypad->base);
err_free_mem:
free_irq(keypad->irq, keypad);
clk_put(keypad->clk);
+ samsung_keypad_dt_gpio_free(keypad);
iounmap(keypad->base);
kfree(keypad);
};
#endif
+#ifdef CONFIG_OF
+static const struct of_device_id samsung_keypad_dt_match[] = {
+ { .compatible = "samsung,s3c6410-keypad" },
+ { .compatible = "samsung,s5pv210-keypad" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, samsung_keypad_dt_match);
+#else
+#define samsung_keypad_dt_match NULL
+#endif
+
static struct platform_device_id samsung_keypad_driver_ids[] = {
{
.name = "samsung-keypad",
.driver = {
.name = "samsung-keypad",
.owner = THIS_MODULE,
+ .of_match_table = samsung_keypad_dt_match,
#ifdef CONFIG_PM
.pm = &samsung_keypad_pm_ops,
#endif
for (clks = 0, ptr = 0; ptr < MAX_BUS_CLK; ptr++) {
struct clk *clk;
- char *name = pdata->clocks[ptr];
-
- if (name == NULL)
- continue;
+ char name[14];
+ snprintf(name, 14, "mmc_busclk.%d", ptr);
clk = clk_get(dev, name);
if (IS_ERR(clk)) {
- dev_err(dev, "failed to get clock %s\n", name);
continue;
}
#include <linux/clk.h>
#include <linux/log2.h>
#include <linux/slab.h>
+#include <linux/of.h>
#include <mach/hardware.h>
#include <asm/uaccess.h>
goto err_nortc;
}
- s3c_rtc_cpu_type = platform_get_device_id(pdev)->driver_data;
+#ifdef CONFIG_OF
+ if (pdev->dev.of_node)
+ s3c_rtc_cpu_type = of_device_is_compatible(pdev->dev.of_node,
+ "samsung,s3c6410-rtc") ? TYPE_S3C64XX : TYPE_S3C2410;
+ else
+#endif
+ s3c_rtc_cpu_type = platform_get_device_id(pdev)->driver_data;
/* Check RTC Time */
#define s3c_rtc_resume NULL
#endif
+#ifdef CONFIG_OF
+static const struct of_device_id s3c_rtc_dt_match[] = {
+ { .compatible = "samsung,s3c2410-rtc" },
+ { .compatible = "samsung,s3c6410-rtc" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, s3c_rtc_dt_match);
+#else
+#define s3c_rtc_dt_match NULL
+#endif
+
static struct platform_device_id s3c_rtc_driver_ids[] = {
{
.name = "s3c2410-rtc",
.driver = {
.name = "s3c-rtc",
.owner = THIS_MODULE,
+ .of_match_table = s3c_rtc_dt_match,
},
};
struct s3c64xx_spi_info *sci;
struct spi_master *master;
int ret;
+ char clk_name[16];
if (pdev->id < 0) {
dev_err(&pdev->dev,
}
sci = pdev->dev.platform_data;
- if (!sci->src_clk_name) {
- dev_err(&pdev->dev,
- "Board init must call s3c64xx_spi_set_info()\n");
- return -EINVAL;
- }
/* Check for availability of necessary resource */
goto err4;
}
- sdd->src_clk = clk_get(&pdev->dev, sci->src_clk_name);
+ sprintf(clk_name, "spi_busclk%d", sci->src_clk_nr);
+ sdd->src_clk = clk_get(&pdev->dev, clk_name);
if (IS_ERR(sdd->src_clk)) {
dev_err(&pdev->dev,
- "Unable to acquire clock '%s'\n", sci->src_clk_name);
+ "Unable to acquire clock '%s'\n", clk_name);
ret = PTR_ERR(sdd->src_clk);
goto err5;
}
if (clk_enable(sdd->src_clk)) {
- dev_err(&pdev->dev, "Couldn't enable clock '%s'\n",
- sci->src_clk_name);
+ dev_err(&pdev->dev, "Couldn't enable clock '%s'\n", clk_name);
ret = -EBUSY;
goto err6;
}
config SERIAL_SAMSUNG_UARTS_4
bool
depends on ARM && PLAT_SAMSUNG
- default y if CPU_S3C2443
+ default y if !(CPU_S3C2410 || SERIAL_S3C2412 || CPU_S3C2440 || CPU_S3C2442)
help
Internal node for the common case of 4 Samsung compatible UARTs
int
depends on ARM && PLAT_SAMSUNG
default 6 if ARCH_S5P6450
- default 4 if SERIAL_SAMSUNG_UARTS_4
+ default 4 if SERIAL_SAMSUNG_UARTS_4 || CPU_S3C2416
default 3
help
Select the number of available UART ports for the Samsung S3C
your boot loader about how to pass options to the kernel at
boot time.)
-config SERIAL_S3C2410
- tristate "Samsung S3C2410 Serial port support"
- depends on SERIAL_SAMSUNG && CPU_S3C2410
- default y if CPU_S3C2410
- help
- Serial port support for the Samsung S3C2410 SoC
-
-config SERIAL_S3C2412
- tristate "Samsung S3C2412/S3C2413 Serial port support"
- depends on SERIAL_SAMSUNG && CPU_S3C2412
- default y if CPU_S3C2412
- help
- Serial port support for the Samsung S3C2412 and S3C2413 SoC
-
-config SERIAL_S3C2440
- tristate "Samsung S3C2440/S3C2442/S3C2416 Serial port support"
- depends on SERIAL_SAMSUNG && (CPU_S3C2440 || CPU_S3C2442 || CPU_S3C2416)
- default y if CPU_S3C2440
- default y if CPU_S3C2442
- select SERIAL_SAMSUNG_UARTS_4 if CPU_S3C2416
- help
- Serial port support for the Samsung S3C2440, S3C2416 and S3C2442 SoC
-
-config SERIAL_S3C6400
- tristate "Samsung S3C6400/S3C6410/S5P6440/S5P6450/S5PC100 Serial port support"
- depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410 || CPU_S5P6440 || CPU_S5P6450 || CPU_S5PC100)
- select SERIAL_SAMSUNG_UARTS_4
- default y
- help
- Serial port support for the Samsung S3C6400, S3C6410, S5P6440, S5P6450
- and S5PC100 SoCs
-
-config SERIAL_S5PV210
- tristate "Samsung S5PV210 Serial port support"
- depends on SERIAL_SAMSUNG && (CPU_S5PV210 || CPU_EXYNOS4210 || SOC_EXYNOS4212)
- select SERIAL_SAMSUNG_UARTS_4 if (CPU_S5PV210 || CPU_EXYNOS4210 || SOC_EXYNOS4212)
- default y
- help
- Serial port support for Samsung's S5P Family of SoC's
-
-
config SERIAL_MAX3100
tristate "MAX3100 support"
depends on SPI
obj-$(CONFIG_SERIAL_BFIN) += bfin_uart.o
obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o
-obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
-obj-$(CONFIG_SERIAL_S3C2412) += s3c2412.o
-obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o
-obj-$(CONFIG_SERIAL_S3C6400) += s3c6400.o
-obj-$(CONFIG_SERIAL_S5PV210) += s5pv210.o
obj-$(CONFIG_SERIAL_MAX3100) += max3100.o
obj-$(CONFIG_SERIAL_MAX3107) += max3107.o
obj-$(CONFIG_SERIAL_MAX3107_AAVA) += max3107-aava.o
+++ /dev/null
-/*
- * Driver for Samsung S3C2410 SoC onboard UARTs.
- *
- * Ben Dooks, Copyright (c) 2003-2008 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
-#include <mach/regs-gpio.h>
-
-#include "samsung.h"
-
-static int s3c2410_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- if (strcmp(clk->name, "uclk") == 0)
- ucon |= S3C2410_UCON_UCLK;
- else
- ucon &= ~S3C2410_UCON_UCLK;
-
- wr_regl(port, S3C2410_UCON, ucon);
- return 0;
-}
-
-static int s3c2410_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- clk->divisor = 1;
- clk->name = (ucon & S3C2410_UCON_UCLK) ? "uclk" : "pclk";
-
- return 0;
-}
-
-static int s3c2410_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- dbg("s3c2410_serial_resetport: port=%p (%08lx), cfg=%p\n",
- port, port->mapbase, cfg);
-
- wr_regl(port, S3C2410_UCON, cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
-
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- return 0;
-}
-
-static struct s3c24xx_uart_info s3c2410_uart_inf = {
- .name = "Samsung S3C2410 UART",
- .type = PORT_S3C2410,
- .fifosize = 16,
- .rx_fifomask = S3C2410_UFSTAT_RXMASK,
- .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT,
- .rx_fifofull = S3C2410_UFSTAT_RXFULL,
- .tx_fifofull = S3C2410_UFSTAT_TXFULL,
- .tx_fifomask = S3C2410_UFSTAT_TXMASK,
- .tx_fifoshift = S3C2410_UFSTAT_TXSHIFT,
- .get_clksrc = s3c2410_serial_getsource,
- .set_clksrc = s3c2410_serial_setsource,
- .reset_port = s3c2410_serial_resetport,
-};
-
-static int s3c2410_serial_probe(struct platform_device *dev)
-{
- return s3c24xx_serial_probe(dev, &s3c2410_uart_inf);
-}
-
-static struct platform_driver s3c2410_serial_driver = {
- .probe = s3c2410_serial_probe,
- .remove = __devexit_p(s3c24xx_serial_remove),
- .driver = {
- .name = "s3c2410-uart",
- .owner = THIS_MODULE,
- },
-};
-
-static int __init s3c2410_serial_init(void)
-{
- return s3c24xx_serial_init(&s3c2410_serial_driver, &s3c2410_uart_inf);
-}
-
-static void __exit s3c2410_serial_exit(void)
-{
- platform_driver_unregister(&s3c2410_serial_driver);
-}
-
-module_init(s3c2410_serial_init);
-module_exit(s3c2410_serial_exit);
-
-MODULE_LICENSE("GPL v2");
-MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_DESCRIPTION("Samsung S3C2410 SoC Serial port driver");
-MODULE_ALIAS("platform:s3c2410-uart");
+++ /dev/null
-/*
- * Driver for Samsung S3C2412 and S3C2413 SoC onboard UARTs.
- *
- * Ben Dooks, Copyright (c) 2003-2008 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
-#include <mach/regs-gpio.h>
-
-#include "samsung.h"
-
-static int s3c2412_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- ucon &= ~S3C2412_UCON_CLKMASK;
-
- if (strcmp(clk->name, "uclk") == 0)
- ucon |= S3C2440_UCON_UCLK;
- else if (strcmp(clk->name, "pclk") == 0)
- ucon |= S3C2440_UCON_PCLK;
- else if (strcmp(clk->name, "usysclk") == 0)
- ucon |= S3C2412_UCON_USYSCLK;
- else {
- printk(KERN_ERR "unknown clock source %s\n", clk->name);
- return -EINVAL;
- }
-
- wr_regl(port, S3C2410_UCON, ucon);
- return 0;
-}
-
-
-static int s3c2412_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- switch (ucon & S3C2412_UCON_CLKMASK) {
- case S3C2412_UCON_UCLK:
- clk->divisor = 1;
- clk->name = "uclk";
- break;
-
- case S3C2412_UCON_PCLK:
- case S3C2412_UCON_PCLK2:
- clk->divisor = 1;
- clk->name = "pclk";
- break;
-
- case S3C2412_UCON_USYSCLK:
- clk->divisor = 1;
- clk->name = "usysclk";
- break;
- }
-
- return 0;
-}
-
-static int s3c2412_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- dbg("%s: port=%p (%08lx), cfg=%p\n",
- __func__, port, port->mapbase, cfg);
-
- /* ensure we don't change the clock settings... */
-
- ucon &= S3C2412_UCON_CLKMASK;
-
- wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
-
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- return 0;
-}
-
-static struct s3c24xx_uart_info s3c2412_uart_inf = {
- .name = "Samsung S3C2412 UART",
- .type = PORT_S3C2412,
- .fifosize = 64,
- .has_divslot = 1,
- .rx_fifomask = S3C2440_UFSTAT_RXMASK,
- .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
- .rx_fifofull = S3C2440_UFSTAT_RXFULL,
- .tx_fifofull = S3C2440_UFSTAT_TXFULL,
- .tx_fifomask = S3C2440_UFSTAT_TXMASK,
- .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
- .get_clksrc = s3c2412_serial_getsource,
- .set_clksrc = s3c2412_serial_setsource,
- .reset_port = s3c2412_serial_resetport,
-};
-
-/* device management */
-
-static int s3c2412_serial_probe(struct platform_device *dev)
-{
- dbg("s3c2440_serial_probe: dev=%p\n", dev);
- return s3c24xx_serial_probe(dev, &s3c2412_uart_inf);
-}
-
-static struct platform_driver s3c2412_serial_driver = {
- .probe = s3c2412_serial_probe,
- .remove = __devexit_p(s3c24xx_serial_remove),
- .driver = {
- .name = "s3c2412-uart",
- .owner = THIS_MODULE,
- },
-};
-
-static inline int s3c2412_serial_init(void)
-{
- return s3c24xx_serial_init(&s3c2412_serial_driver, &s3c2412_uart_inf);
-}
-
-static inline void s3c2412_serial_exit(void)
-{
- platform_driver_unregister(&s3c2412_serial_driver);
-}
-
-module_init(s3c2412_serial_init);
-module_exit(s3c2412_serial_exit);
-
-MODULE_DESCRIPTION("Samsung S3C2412,S3C2413 SoC Serial port driver");
-MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:s3c2412-uart");
+++ /dev/null
-/*
- * Driver for Samsung S3C2440 and S3C2442 SoC onboard UARTs.
- *
- * Ben Dooks, Copyright (c) 2003-2008 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
-#include <mach/regs-gpio.h>
-
-#include "samsung.h"
-
-
-static int s3c2440_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- /* todo - proper fclk<>nonfclk switch. */
-
- ucon &= ~S3C2440_UCON_CLKMASK;
-
- if (strcmp(clk->name, "uclk") == 0)
- ucon |= S3C2440_UCON_UCLK;
- else if (strcmp(clk->name, "pclk") == 0)
- ucon |= S3C2440_UCON_PCLK;
- else if (strcmp(clk->name, "fclk") == 0)
- ucon |= S3C2440_UCON_FCLK;
- else {
- printk(KERN_ERR "unknown clock source %s\n", clk->name);
- return -EINVAL;
- }
-
- wr_regl(port, S3C2410_UCON, ucon);
- return 0;
-}
-
-
-static int s3c2440_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
- unsigned long ucon0, ucon1, ucon2;
-
- switch (ucon & S3C2440_UCON_CLKMASK) {
- case S3C2440_UCON_UCLK:
- clk->divisor = 1;
- clk->name = "uclk";
- break;
-
- case S3C2440_UCON_PCLK:
- case S3C2440_UCON_PCLK2:
- clk->divisor = 1;
- clk->name = "pclk";
- break;
-
- case S3C2440_UCON_FCLK:
- /* the fun of calculating the uart divisors on
- * the s3c2440 */
-
- ucon0 = __raw_readl(S3C24XX_VA_UART0 + S3C2410_UCON);
- ucon1 = __raw_readl(S3C24XX_VA_UART1 + S3C2410_UCON);
- ucon2 = __raw_readl(S3C24XX_VA_UART2 + S3C2410_UCON);
-
- printk("ucons: %08lx, %08lx, %08lx\n", ucon0, ucon1, ucon2);
-
- ucon0 &= S3C2440_UCON0_DIVMASK;
- ucon1 &= S3C2440_UCON1_DIVMASK;
- ucon2 &= S3C2440_UCON2_DIVMASK;
-
- if (ucon0 != 0) {
- clk->divisor = ucon0 >> S3C2440_UCON_DIVSHIFT;
- clk->divisor += 6;
- } else if (ucon1 != 0) {
- clk->divisor = ucon1 >> S3C2440_UCON_DIVSHIFT;
- clk->divisor += 21;
- } else if (ucon2 != 0) {
- clk->divisor = ucon2 >> S3C2440_UCON_DIVSHIFT;
- clk->divisor += 36;
- } else {
- /* manual calims 44, seems to be 9 */
- clk->divisor = 9;
- }
-
- clk->name = "fclk";
- break;
- }
-
- return 0;
-}
-
-static int s3c2440_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- dbg("s3c2440_serial_resetport: port=%p (%08lx), cfg=%p\n",
- port, port->mapbase, cfg);
-
- /* ensure we don't change the clock settings... */
-
- ucon &= (S3C2440_UCON0_DIVMASK | (3<<10));
-
- wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
-
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- return 0;
-}
-
-static struct s3c24xx_uart_info s3c2440_uart_inf = {
- .name = "Samsung S3C2440 UART",
- .type = PORT_S3C2440,
- .fifosize = 64,
- .rx_fifomask = S3C2440_UFSTAT_RXMASK,
- .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
- .rx_fifofull = S3C2440_UFSTAT_RXFULL,
- .tx_fifofull = S3C2440_UFSTAT_TXFULL,
- .tx_fifomask = S3C2440_UFSTAT_TXMASK,
- .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
- .get_clksrc = s3c2440_serial_getsource,
- .set_clksrc = s3c2440_serial_setsource,
- .reset_port = s3c2440_serial_resetport,
-};
-
-/* device management */
-
-static int s3c2440_serial_probe(struct platform_device *dev)
-{
- dbg("s3c2440_serial_probe: dev=%p\n", dev);
- return s3c24xx_serial_probe(dev, &s3c2440_uart_inf);
-}
-
-static struct platform_driver s3c2440_serial_driver = {
- .probe = s3c2440_serial_probe,
- .remove = __devexit_p(s3c24xx_serial_remove),
- .driver = {
- .name = "s3c2440-uart",
- .owner = THIS_MODULE,
- },
-};
-
-static int __init s3c2440_serial_init(void)
-{
- return s3c24xx_serial_init(&s3c2440_serial_driver, &s3c2440_uart_inf);
-}
-
-static void __exit s3c2440_serial_exit(void)
-{
- platform_driver_unregister(&s3c2440_serial_driver);
-}
-
-module_init(s3c2440_serial_init);
-module_exit(s3c2440_serial_exit);
-
-MODULE_DESCRIPTION("Samsung S3C2440,S3C2442 SoC Serial port driver");
-MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:s3c2440-uart");
+++ /dev/null
-/*
- * Driver for Samsung S3C6400 and S3C6410 SoC onboard UARTs.
- *
- * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- * http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
-
-#include "samsung.h"
-
-static int s3c6400_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- if (strcmp(clk->name, "uclk0") == 0) {
- ucon &= ~S3C6400_UCON_CLKMASK;
- ucon |= S3C6400_UCON_UCLK0;
- } else if (strcmp(clk->name, "uclk1") == 0)
- ucon |= S3C6400_UCON_UCLK1;
- else if (strcmp(clk->name, "pclk") == 0) {
- /* See notes about transitioning from UCLK to PCLK */
- ucon &= ~S3C6400_UCON_UCLK0;
- } else {
- printk(KERN_ERR "unknown clock source %s\n", clk->name);
- return -EINVAL;
- }
-
- wr_regl(port, S3C2410_UCON, ucon);
- return 0;
-}
-
-
-static int s3c6400_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- u32 ucon = rd_regl(port, S3C2410_UCON);
-
- clk->divisor = 1;
-
- switch (ucon & S3C6400_UCON_CLKMASK) {
- case S3C6400_UCON_UCLK0:
- clk->name = "uclk0";
- break;
-
- case S3C6400_UCON_UCLK1:
- clk->name = "uclk1";
- break;
-
- case S3C6400_UCON_PCLK:
- case S3C6400_UCON_PCLK2:
- clk->name = "pclk";
- break;
- }
-
- return 0;
-}
-
-static int s3c6400_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- dbg("s3c6400_serial_resetport: port=%p (%08lx), cfg=%p\n",
- port, port->mapbase, cfg);
-
- /* ensure we don't change the clock settings... */
-
- ucon &= S3C6400_UCON_CLKMASK;
-
- wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
-
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- return 0;
-}
-
-static struct s3c24xx_uart_info s3c6400_uart_inf = {
- .name = "Samsung S3C6400 UART",
- .type = PORT_S3C6400,
- .fifosize = 64,
- .has_divslot = 1,
- .rx_fifomask = S3C2440_UFSTAT_RXMASK,
- .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
- .rx_fifofull = S3C2440_UFSTAT_RXFULL,
- .tx_fifofull = S3C2440_UFSTAT_TXFULL,
- .tx_fifomask = S3C2440_UFSTAT_TXMASK,
- .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
- .get_clksrc = s3c6400_serial_getsource,
- .set_clksrc = s3c6400_serial_setsource,
- .reset_port = s3c6400_serial_resetport,
-};
-
-/* device management */
-
-static int s3c6400_serial_probe(struct platform_device *dev)
-{
- dbg("s3c6400_serial_probe: dev=%p\n", dev);
- return s3c24xx_serial_probe(dev, &s3c6400_uart_inf);
-}
-
-static struct platform_driver s3c6400_serial_driver = {
- .probe = s3c6400_serial_probe,
- .remove = __devexit_p(s3c24xx_serial_remove),
- .driver = {
- .name = "s3c6400-uart",
- .owner = THIS_MODULE,
- },
-};
-
-static int __init s3c6400_serial_init(void)
-{
- return s3c24xx_serial_init(&s3c6400_serial_driver, &s3c6400_uart_inf);
-}
-
-static void __exit s3c6400_serial_exit(void)
-{
- platform_driver_unregister(&s3c6400_serial_driver);
-}
-
-module_init(s3c6400_serial_init);
-module_exit(s3c6400_serial_exit);
-
-MODULE_DESCRIPTION("Samsung S3C6400,S3C6410 SoC Serial port driver");
-MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:s3c6400-uart");
+++ /dev/null
-/*
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
- * http://www.samsung.com/
- *
- * Based on drivers/serial/s3c6400.c
- *
- * Driver for Samsung S5PV210 SoC UARTs.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-#include <linux/delay.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-#include <plat/regs-serial.h>
-#include "samsung.h"
-
-static int s5pv210_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- struct s3c2410_uartcfg *cfg = port->dev->platform_data;
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- if (cfg->flags & NO_NEED_CHECK_CLKSRC)
- return 0;
-
- if (strcmp(clk->name, "pclk") == 0)
- ucon &= ~S5PV210_UCON_CLKMASK;
- else if (strcmp(clk->name, "uclk1") == 0)
- ucon |= S5PV210_UCON_CLKMASK;
- else {
- printk(KERN_ERR "unknown clock source %s\n", clk->name);
- return -EINVAL;
- }
-
- wr_regl(port, S3C2410_UCON, ucon);
- return 0;
-}
-
-
-static int s5pv210_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- struct s3c2410_uartcfg *cfg = port->dev->platform_data;
- u32 ucon = rd_regl(port, S3C2410_UCON);
-
- clk->divisor = 1;
-
- if (cfg->flags & NO_NEED_CHECK_CLKSRC)
- return 0;
-
- switch (ucon & S5PV210_UCON_CLKMASK) {
- case S5PV210_UCON_PCLK:
- clk->name = "pclk";
- break;
- case S5PV210_UCON_UCLK:
- clk->name = "uclk1";
- break;
- }
-
- return 0;
-}
-
-static int s5pv210_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- ucon &= S5PV210_UCON_CLKMASK;
- wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- /* It is need to delay When reset FIFO register */
- udelay(1);
-
- return 0;
-}
-
-#define S5PV210_UART_DEFAULT_INFO(fifo_size) \
- .name = "Samsung S5PV210 UART0", \
- .type = PORT_S3C6400, \
- .fifosize = fifo_size, \
- .has_divslot = 1, \
- .rx_fifomask = S5PV210_UFSTAT_RXMASK, \
- .rx_fifoshift = S5PV210_UFSTAT_RXSHIFT, \
- .rx_fifofull = S5PV210_UFSTAT_RXFULL, \
- .tx_fifofull = S5PV210_UFSTAT_TXFULL, \
- .tx_fifomask = S5PV210_UFSTAT_TXMASK, \
- .tx_fifoshift = S5PV210_UFSTAT_TXSHIFT, \
- .get_clksrc = s5pv210_serial_getsource, \
- .set_clksrc = s5pv210_serial_setsource, \
- .reset_port = s5pv210_serial_resetport
-
-static struct s3c24xx_uart_info s5p_port_fifo256 = {
- S5PV210_UART_DEFAULT_INFO(256),
-};
-
-static struct s3c24xx_uart_info s5p_port_fifo64 = {
- S5PV210_UART_DEFAULT_INFO(64),
-};
-
-static struct s3c24xx_uart_info s5p_port_fifo16 = {
- S5PV210_UART_DEFAULT_INFO(16),
-};
-
-static struct s3c24xx_uart_info *s5p_uart_inf[] = {
- [0] = &s5p_port_fifo256,
- [1] = &s5p_port_fifo64,
- [2] = &s5p_port_fifo16,
- [3] = &s5p_port_fifo16,
-};
-
-/* device management */
-static int s5p_serial_probe(struct platform_device *pdev)
-{
- return s3c24xx_serial_probe(pdev, s5p_uart_inf[pdev->id]);
-}
-
-static struct platform_driver s5p_serial_driver = {
- .probe = s5p_serial_probe,
- .remove = __devexit_p(s3c24xx_serial_remove),
- .driver = {
- .name = "s5pv210-uart",
- .owner = THIS_MODULE,
- },
-};
-
-static int __init s5p_serial_init(void)
-{
- return s3c24xx_serial_init(&s5p_serial_driver, *s5p_uart_inf);
-}
-
-static void __exit s5p_serial_exit(void)
-{
- platform_driver_unregister(&s5p_serial_driver);
-}
-
-module_init(s5p_serial_init);
-module_exit(s5p_serial_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:s5pv210-uart");
-MODULE_DESCRIPTION("Samsung S5PV210 UART Driver support");
-MODULE_AUTHOR("Thomas Abraham <thomas.ab@samsung.com>");
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/cpufreq.h>
+#include <linux/of.h>
#include <asm/irq.h>
#include <mach/map.h>
#include <plat/regs-serial.h>
+#include <plat/clock.h>
#include "samsung.h"
static inline struct s3c2410_uartcfg *s3c24xx_port_to_cfg(struct uart_port *port)
{
+ struct s3c24xx_uart_port *ourport;
+
if (port->dev == NULL)
return NULL;
- return (struct s3c2410_uartcfg *)port->dev->platform_data;
+ ourport = container_of(port, struct s3c24xx_uart_port, port);
+ return ourport->cfg;
}
static int s3c24xx_serial_rx_fifocnt(struct s3c24xx_uart_port *ourport,
struct s3c24xx_uart_info *info = ourport->info;
if (ufstat & info->rx_fifofull)
- return info->fifosize;
+ return ourport->port.fifosize;
return (ufstat & info->rx_fifomask) >> info->rx_fifoshift;
}
*
*/
+#define MAX_CLK_NAME_LENGTH 15
-#define MAX_CLKS (8)
-
-static struct s3c24xx_uart_clksrc tmp_clksrc = {
- .name = "pclk",
- .min_baud = 0,
- .max_baud = 0,
- .divisor = 1,
-};
-
-static inline int
-s3c24xx_serial_getsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c)
+static inline int s3c24xx_serial_getsource(struct uart_port *port)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+ unsigned int ucon;
- return (info->get_clksrc)(port, c);
-}
-
-static inline int
-s3c24xx_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c)
-{
- struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+ if (info->num_clks == 1)
+ return 0;
- return (info->set_clksrc)(port, c);
+ ucon = rd_regl(port, S3C2410_UCON);
+ ucon &= info->clksel_mask;
+ return ucon >> info->clksel_shift;
}
-struct baud_calc {
- struct s3c24xx_uart_clksrc *clksrc;
- unsigned int calc;
- unsigned int divslot;
- unsigned int quot;
- struct clk *src;
-};
-
-static int s3c24xx_serial_calcbaud(struct baud_calc *calc,
- struct uart_port *port,
- struct s3c24xx_uart_clksrc *clksrc,
- unsigned int baud)
+static void s3c24xx_serial_setsource(struct uart_port *port,
+ unsigned int clk_sel)
{
- struct s3c24xx_uart_port *ourport = to_ourport(port);
- unsigned long rate;
-
- calc->src = clk_get(port->dev, clksrc->name);
- if (calc->src == NULL || IS_ERR(calc->src))
- return 0;
-
- rate = clk_get_rate(calc->src);
- rate /= clksrc->divisor;
+ struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+ unsigned int ucon;
- calc->clksrc = clksrc;
+ if (info->num_clks == 1)
+ return;
- if (ourport->info->has_divslot) {
- unsigned long div = rate / baud;
-
- /* The UDIVSLOT register on the newer UARTs allows us to
- * get a divisor adjustment of 1/16th on the baud clock.
- *
- * We don't keep the UDIVSLOT value (the 16ths we calculated
- * by not multiplying the baud by 16) as it is easy enough
- * to recalculate.
- */
-
- calc->quot = div / 16;
- calc->calc = rate / div;
- } else {
- calc->quot = (rate + (8 * baud)) / (16 * baud);
- calc->calc = (rate / (calc->quot * 16));
- }
+ ucon = rd_regl(port, S3C2410_UCON);
+ if ((ucon & info->clksel_mask) >> info->clksel_shift == clk_sel)
+ return;
- calc->quot--;
- return 1;
+ ucon &= ~info->clksel_mask;
+ ucon |= clk_sel << info->clksel_shift;
+ wr_regl(port, S3C2410_UCON, ucon);
}
-static unsigned int s3c24xx_serial_getclk(struct uart_port *port,
- struct s3c24xx_uart_clksrc **clksrc,
- struct clk **clk,
- unsigned int baud)
+static unsigned int s3c24xx_serial_getclk(struct s3c24xx_uart_port *ourport,
+ unsigned int req_baud, struct clk **best_clk,
+ unsigned int *clk_num)
{
- struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
- struct s3c24xx_uart_clksrc *clkp;
- struct baud_calc res[MAX_CLKS];
- struct baud_calc *resptr, *best, *sptr;
- int i;
-
- clkp = cfg->clocks;
- best = NULL;
-
- if (cfg->clocks_size < 2) {
- if (cfg->clocks_size == 0)
- clkp = &tmp_clksrc;
-
- /* check to see if we're sourcing fclk, and if so we're
- * going to have to update the clock source
- */
-
- if (strcmp(clkp->name, "fclk") == 0) {
- struct s3c24xx_uart_clksrc src;
-
- s3c24xx_serial_getsource(port, &src);
-
- /* check that the port already using fclk, and if
- * not, then re-select fclk
+ struct s3c24xx_uart_info *info = ourport->info;
+ struct clk *clk;
+ unsigned long rate;
+ unsigned int cnt, baud, quot, clk_sel, best_quot = 0;
+ char clkname[MAX_CLK_NAME_LENGTH];
+ int calc_deviation, deviation = (1 << 30) - 1;
+
+ *best_clk = NULL;
+ clk_sel = (ourport->cfg->clk_sel) ? ourport->cfg->clk_sel :
+ ourport->info->def_clk_sel;
+ for (cnt = 0; cnt < info->num_clks; cnt++) {
+ if (!(clk_sel & (1 << cnt)))
+ continue;
+
+ sprintf(clkname, "clk_uart_baud%d", cnt);
+ clk = clk_get(ourport->port.dev, clkname);
+ if (IS_ERR_OR_NULL(clk))
+ continue;
+
+ rate = clk_get_rate(clk);
+ if (!rate)
+ continue;
+
+ if (ourport->info->has_divslot) {
+ unsigned long div = rate / req_baud;
+
+ /* The UDIVSLOT register on the newer UARTs allows us to
+ * get a divisor adjustment of 1/16th on the baud clock.
+ *
+ * We don't keep the UDIVSLOT value (the 16ths we
+ * calculated by not multiplying the baud by 16) as it
+ * is easy enough to recalculate.
*/
- if (strcmp(src.name, clkp->name) == 0) {
- s3c24xx_serial_setsource(port, clkp);
- s3c24xx_serial_getsource(port, &src);
- }
-
- clkp->divisor = src.divisor;
- }
-
- s3c24xx_serial_calcbaud(res, port, clkp, baud);
- best = res;
- resptr = best + 1;
- } else {
- resptr = res;
-
- for (i = 0; i < cfg->clocks_size; i++, clkp++) {
- if (s3c24xx_serial_calcbaud(resptr, port, clkp, baud))
- resptr++;
+ quot = div / 16;
+ baud = rate / div;
+ } else {
+ quot = (rate + (8 * req_baud)) / (16 * req_baud);
+ baud = rate / (quot * 16);
}
- }
-
- /* ok, we now need to select the best clock we found */
-
- if (!best) {
- unsigned int deviation = (1<<30)|((1<<30)-1);
- int calc_deviation;
+ quot--;
- for (sptr = res; sptr < resptr; sptr++) {
- calc_deviation = baud - sptr->calc;
- if (calc_deviation < 0)
- calc_deviation = -calc_deviation;
+ calc_deviation = req_baud - baud;
+ if (calc_deviation < 0)
+ calc_deviation = -calc_deviation;
- if (calc_deviation < deviation) {
- best = sptr;
- deviation = calc_deviation;
- }
+ if (calc_deviation < deviation) {
+ *best_clk = clk;
+ best_quot = quot;
+ *clk_num = cnt;
+ deviation = calc_deviation;
}
}
- /* store results to pass back */
-
- *clksrc = best->clksrc;
- *clk = best->src;
-
- return best->quot;
+ return best_quot;
}
/* udivslot_table[]
{
struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
struct s3c24xx_uart_port *ourport = to_ourport(port);
- struct s3c24xx_uart_clksrc *clksrc = NULL;
struct clk *clk = NULL;
unsigned long flags;
- unsigned int baud, quot;
+ unsigned int baud, quot, clk_sel = 0;
unsigned int ulcon;
unsigned int umcon;
unsigned int udivslot = 0;
*/
baud = uart_get_baud_rate(port, termios, old, 0, 115200*8);
-
+ quot = s3c24xx_serial_getclk(ourport, baud, &clk, &clk_sel);
if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST)
quot = port->custom_divisor;
- else
- quot = s3c24xx_serial_getclk(port, &clksrc, &clk, baud);
+ if (!clk)
+ return;
/* check to see if we need to change clock source */
- if (ourport->clksrc != clksrc || ourport->baudclk != clk) {
- dbg("selecting clock %p\n", clk);
- s3c24xx_serial_setsource(port, clksrc);
+ if (ourport->baudclk != clk) {
+ s3c24xx_serial_setsource(port, clk_sel);
if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) {
clk_disable(ourport->baudclk);
clk_enable(clk);
- ourport->clksrc = clksrc;
ourport->baudclk = clk;
ourport->baudclk_rate = clk ? clk_get_rate(clk) : 0;
}
/* s3c24xx_serial_resetport
*
- * wrapper to call the specific reset for this port (reset the fifos
- * and the settings)
+ * reset the fifos and other the settings.
*/
-static inline int s3c24xx_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
+static void s3c24xx_serial_resetport(struct uart_port *port,
+ struct s3c2410_uartcfg *cfg)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+ unsigned long ucon = rd_regl(port, S3C2410_UCON);
+ unsigned int ucon_mask;
+
+ ucon_mask = info->clksel_mask;
+ if (info->type == PORT_S3C2440)
+ ucon_mask |= S3C2440_UCON0_DIVMASK;
- return (info->reset_port)(port, cfg);
+ ucon &= ucon_mask;
+ wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
+
+ /* reset both fifos */
+ wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
+ wr_regl(port, S3C2410_UFCON, cfg->ufcon);
+
+ /* some delay is required after fifo reset */
+ udelay(1);
}
*/
static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
- struct s3c24xx_uart_info *info,
struct platform_device *platdev)
{
struct uart_port *port = &ourport->port;
- struct s3c2410_uartcfg *cfg;
+ struct s3c2410_uartcfg *cfg = ourport->cfg;
struct resource *res;
int ret;
if (platdev == NULL)
return -ENODEV;
- cfg = s3c24xx_dev_to_cfg(&platdev->dev);
-
if (port->mapbase != 0)
return 0;
- if (cfg->hwport > CONFIG_SERIAL_SAMSUNG_UARTS) {
- printk(KERN_ERR "%s: port %d bigger than %d\n", __func__,
- cfg->hwport, CONFIG_SERIAL_SAMSUNG_UARTS);
- return -ERANGE;
- }
-
/* setup info for port */
port->dev = &platdev->dev;
- ourport->info = info;
/* Startup sequence is different for s3c64xx and higher SoC's */
if (s3c24xx_serial_has_interrupt_mask(port))
s3c24xx_serial_ops.startup = s3c64xx_serial_startup;
- /* copy the info in from provided structure */
- ourport->port.fifosize = info->fifosize;
-
- dbg("s3c24xx_serial_init_port: %p (hw %d)...\n", port, cfg->hwport);
-
port->uartclk = 1;
if (cfg->uart_flags & UPF_CONS_FLOW) {
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
- return snprintf(buf, PAGE_SIZE, "* %s\n", ourport->clksrc->name);
+ return snprintf(buf, PAGE_SIZE, "* %s\n", ourport->baudclk->name);
}
static DEVICE_ATTR(clock_source, S_IRUGO, s3c24xx_serial_show_clksrc, NULL);
+
/* Device driver serial port probe */
+static const struct of_device_id s3c24xx_uart_dt_match[];
static int probe_index;
-int s3c24xx_serial_probe(struct platform_device *dev,
- struct s3c24xx_uart_info *info)
+static inline struct s3c24xx_serial_drv_data *s3c24xx_get_driver_data(
+ struct platform_device *pdev)
+{
+#ifdef CONFIG_OF
+ if (pdev->dev.of_node) {
+ const struct of_device_id *match;
+ match = of_match_node(s3c24xx_uart_dt_match, pdev->dev.of_node);
+ return (struct s3c24xx_serial_drv_data *)match->data;
+ }
+#endif
+ return (struct s3c24xx_serial_drv_data *)
+ platform_get_device_id(pdev)->driver_data;
+}
+
+static int s3c24xx_serial_probe(struct platform_device *pdev)
{
struct s3c24xx_uart_port *ourport;
int ret;
- dbg("s3c24xx_serial_probe(%p, %p) %d\n", dev, info, probe_index);
+ dbg("s3c24xx_serial_probe(%p) %d\n", pdev, probe_index);
ourport = &s3c24xx_serial_ports[probe_index];
+
+ ourport->drv_data = s3c24xx_get_driver_data(pdev);
+ if (!ourport->drv_data) {
+ dev_err(&pdev->dev, "could not find driver data\n");
+ return -ENODEV;
+ }
+
+ ourport->info = ourport->drv_data->info;
+ ourport->cfg = (pdev->dev.platform_data) ?
+ (struct s3c2410_uartcfg *)pdev->dev.platform_data :
+ ourport->drv_data->def_cfg;
+
+ ourport->port.fifosize = (ourport->info->fifosize) ?
+ ourport->info->fifosize :
+ ourport->drv_data->fifosize[probe_index];
+
probe_index++;
dbg("%s: initialising port %p...\n", __func__, ourport);
- ret = s3c24xx_serial_init_port(ourport, info, dev);
+ ret = s3c24xx_serial_init_port(ourport, pdev);
if (ret < 0)
goto probe_err;
dbg("%s: adding port\n", __func__);
uart_add_one_port(&s3c24xx_uart_drv, &ourport->port);
- platform_set_drvdata(dev, &ourport->port);
+ platform_set_drvdata(pdev, &ourport->port);
- ret = device_create_file(&dev->dev, &dev_attr_clock_source);
+ ret = device_create_file(&pdev->dev, &dev_attr_clock_source);
if (ret < 0)
- printk(KERN_ERR "%s: failed to add clksrc attr.\n", __func__);
+ dev_err(&pdev->dev, "failed to add clock source attr.\n");
ret = s3c24xx_serial_cpufreq_register(ourport);
if (ret < 0)
- dev_err(&dev->dev, "failed to add cpufreq notifier\n");
+ dev_err(&pdev->dev, "failed to add cpufreq notifier\n");
return 0;
return ret;
}
-EXPORT_SYMBOL_GPL(s3c24xx_serial_probe);
-
-int __devexit s3c24xx_serial_remove(struct platform_device *dev)
+static int __devexit s3c24xx_serial_remove(struct platform_device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
return 0;
}
-EXPORT_SYMBOL_GPL(s3c24xx_serial_remove);
-
/* UART power management code */
#ifdef CONFIG_PM_SLEEP
static int s3c24xx_serial_suspend(struct device *dev)
#define SERIAL_SAMSUNG_PM_OPS NULL
#endif /* CONFIG_PM_SLEEP */
-int s3c24xx_serial_init(struct platform_driver *drv,
- struct s3c24xx_uart_info *info)
-{
- dbg("s3c24xx_serial_init(%p,%p)\n", drv, info);
-
- drv->driver.pm = SERIAL_SAMSUNG_PM_OPS;
-
- return platform_driver_register(drv);
-}
-
-EXPORT_SYMBOL_GPL(s3c24xx_serial_init);
-
-/* module initialisation code */
-
-static int __init s3c24xx_serial_modinit(void)
-{
- int ret;
-
- ret = uart_register_driver(&s3c24xx_uart_drv);
- if (ret < 0) {
- printk(KERN_ERR "failed to register UART driver\n");
- return -1;
- }
-
- return 0;
-}
-
-static void __exit s3c24xx_serial_modexit(void)
-{
- uart_unregister_driver(&s3c24xx_uart_drv);
-}
-
-module_init(s3c24xx_serial_modinit);
-module_exit(s3c24xx_serial_modexit);
-
/* Console code */
#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
s3c24xx_serial_get_options(struct uart_port *port, int *baud,
int *parity, int *bits)
{
- struct s3c24xx_uart_clksrc clksrc;
struct clk *clk;
unsigned int ulcon;
unsigned int ucon;
unsigned int ubrdiv;
unsigned long rate;
+ unsigned int clk_sel;
+ char clk_name[MAX_CLK_NAME_LENGTH];
ulcon = rd_regl(port, S3C2410_ULCON);
ucon = rd_regl(port, S3C2410_UCON);
/* now calculate the baud rate */
- s3c24xx_serial_getsource(port, &clksrc);
+ clk_sel = s3c24xx_serial_getsource(port);
+ sprintf(clk_name, "clk_uart_baud%d", clk_sel);
- clk = clk_get(port->dev, clksrc.name);
+ clk = clk_get(port->dev, clk_name);
if (!IS_ERR(clk) && clk != NULL)
- rate = clk_get_rate(clk) / clksrc.divisor;
+ rate = clk_get_rate(clk);
else
rate = 1;
-
*baud = rate / (16 * (ubrdiv + 1));
dbg("calculated baud %d\n", *baud);
}
}
-/* s3c24xx_serial_init_ports
- *
- * initialise the serial ports from the machine provided initialisation
- * data.
-*/
-
-static int s3c24xx_serial_init_ports(struct s3c24xx_uart_info **info)
-{
- struct s3c24xx_uart_port *ptr = s3c24xx_serial_ports;
- struct platform_device **platdev_ptr;
- int i;
-
- dbg("s3c24xx_serial_init_ports: initialising ports...\n");
-
- platdev_ptr = s3c24xx_uart_devs;
-
- for (i = 0; i < CONFIG_SERIAL_SAMSUNG_UARTS; i++, ptr++, platdev_ptr++) {
- s3c24xx_serial_init_port(ptr, info[i], *platdev_ptr);
- }
-
- return 0;
-}
-
static int __init
s3c24xx_serial_console_setup(struct console *co, char *options)
{
return uart_set_options(port, co, baud, parity, bits, flow);
}
-/* s3c24xx_serial_initconsole
- *
- * initialise the console from one of the uart drivers
-*/
-
static struct console s3c24xx_serial_console = {
.name = S3C24XX_SERIAL_NAME,
.device = uart_console_device,
.setup = s3c24xx_serial_console_setup,
.data = &s3c24xx_uart_drv,
};
+#endif /* CONFIG_SERIAL_SAMSUNG_CONSOLE */
-int s3c24xx_serial_initconsole(struct platform_driver *drv,
- struct s3c24xx_uart_info **info)
+#ifdef CONFIG_CPU_S3C2410
+static struct s3c24xx_serial_drv_data s3c2410_serial_drv_data = {
+ .info = &(struct s3c24xx_uart_info) {
+ .name = "Samsung S3C2410 UART",
+ .type = PORT_S3C2410,
+ .fifosize = 16,
+ .rx_fifomask = S3C2410_UFSTAT_RXMASK,
+ .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT,
+ .rx_fifofull = S3C2410_UFSTAT_RXFULL,
+ .tx_fifofull = S3C2410_UFSTAT_TXFULL,
+ .tx_fifomask = S3C2410_UFSTAT_TXMASK,
+ .tx_fifoshift = S3C2410_UFSTAT_TXSHIFT,
+ .def_clk_sel = S3C2410_UCON_CLKSEL0,
+ .num_clks = 2,
+ .clksel_mask = S3C2410_UCON_CLKMASK,
+ .clksel_shift = S3C2410_UCON_CLKSHIFT,
+ },
+ .def_cfg = &(struct s3c2410_uartcfg) {
+ .ucon = S3C2410_UCON_DEFAULT,
+ .ufcon = S3C2410_UFCON_DEFAULT,
+ },
+};
+#define S3C2410_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c2410_serial_drv_data)
+#else
+#define S3C2410_SERIAL_DRV_DATA (kernel_ulong_t)NULL
+#endif
-{
- struct platform_device *dev = s3c24xx_uart_devs[0];
+#ifdef CONFIG_CPU_S3C2412
+static struct s3c24xx_serial_drv_data s3c2412_serial_drv_data = {
+ .info = &(struct s3c24xx_uart_info) {
+ .name = "Samsung S3C2412 UART",
+ .type = PORT_S3C2412,
+ .fifosize = 64,
+ .has_divslot = 1,
+ .rx_fifomask = S3C2440_UFSTAT_RXMASK,
+ .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
+ .rx_fifofull = S3C2440_UFSTAT_RXFULL,
+ .tx_fifofull = S3C2440_UFSTAT_TXFULL,
+ .tx_fifomask = S3C2440_UFSTAT_TXMASK,
+ .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
+ .def_clk_sel = S3C2410_UCON_CLKSEL2,
+ .num_clks = 4,
+ .clksel_mask = S3C2412_UCON_CLKMASK,
+ .clksel_shift = S3C2412_UCON_CLKSHIFT,
+ },
+ .def_cfg = &(struct s3c2410_uartcfg) {
+ .ucon = S3C2410_UCON_DEFAULT,
+ .ufcon = S3C2410_UFCON_DEFAULT,
+ },
+};
+#define S3C2412_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c2412_serial_drv_data)
+#else
+#define S3C2412_SERIAL_DRV_DATA (kernel_ulong_t)NULL
+#endif
- dbg("s3c24xx_serial_initconsole\n");
+#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2416) || \
+ defined(CONFIG_CPU_S3C2443)
+static struct s3c24xx_serial_drv_data s3c2440_serial_drv_data = {
+ .info = &(struct s3c24xx_uart_info) {
+ .name = "Samsung S3C2440 UART",
+ .type = PORT_S3C2440,
+ .fifosize = 64,
+ .has_divslot = 1,
+ .rx_fifomask = S3C2440_UFSTAT_RXMASK,
+ .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
+ .rx_fifofull = S3C2440_UFSTAT_RXFULL,
+ .tx_fifofull = S3C2440_UFSTAT_TXFULL,
+ .tx_fifomask = S3C2440_UFSTAT_TXMASK,
+ .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
+ .def_clk_sel = S3C2410_UCON_CLKSEL2,
+ .num_clks = 4,
+ .clksel_mask = S3C2412_UCON_CLKMASK,
+ .clksel_shift = S3C2412_UCON_CLKSHIFT,
+ },
+ .def_cfg = &(struct s3c2410_uartcfg) {
+ .ucon = S3C2410_UCON_DEFAULT,
+ .ufcon = S3C2410_UFCON_DEFAULT,
+ },
+};
+#define S3C2440_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c2440_serial_drv_data)
+#else
+#define S3C2440_SERIAL_DRV_DATA (kernel_ulong_t)NULL
+#endif
- /* select driver based on the cpu */
+#if defined(CONFIG_CPU_S3C6400) || defined(CONFIG_CPU_S3C6410) || \
+ defined(CONFIG_CPU_S5P6440) || defined(CONFIG_CPU_S5P6450) || \
+ defined(CONFIG_CPU_S5PC100)
+static struct s3c24xx_serial_drv_data s3c6400_serial_drv_data = {
+ .info = &(struct s3c24xx_uart_info) {
+ .name = "Samsung S3C6400 UART",
+ .type = PORT_S3C6400,
+ .fifosize = 64,
+ .has_divslot = 1,
+ .rx_fifomask = S3C2440_UFSTAT_RXMASK,
+ .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
+ .rx_fifofull = S3C2440_UFSTAT_RXFULL,
+ .tx_fifofull = S3C2440_UFSTAT_TXFULL,
+ .tx_fifomask = S3C2440_UFSTAT_TXMASK,
+ .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
+ .def_clk_sel = S3C2410_UCON_CLKSEL2,
+ .num_clks = 4,
+ .clksel_mask = S3C6400_UCON_CLKMASK,
+ .clksel_shift = S3C6400_UCON_CLKSHIFT,
+ },
+ .def_cfg = &(struct s3c2410_uartcfg) {
+ .ucon = S3C2410_UCON_DEFAULT,
+ .ufcon = S3C2410_UFCON_DEFAULT,
+ },
+};
+#define S3C6400_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c6400_serial_drv_data)
+#else
+#define S3C6400_SERIAL_DRV_DATA (kernel_ulong_t)NULL
+#endif
- if (dev == NULL) {
- printk(KERN_ERR "s3c24xx: no devices for console init\n");
- return 0;
- }
+#ifdef CONFIG_CPU_S5PV210
+static struct s3c24xx_serial_drv_data s5pv210_serial_drv_data = {
+ .info = &(struct s3c24xx_uart_info) {
+ .name = "Samsung S5PV210 UART",
+ .type = PORT_S3C6400,
+ .has_divslot = 1,
+ .rx_fifomask = S5PV210_UFSTAT_RXMASK,
+ .rx_fifoshift = S5PV210_UFSTAT_RXSHIFT,
+ .rx_fifofull = S5PV210_UFSTAT_RXFULL,
+ .tx_fifofull = S5PV210_UFSTAT_TXFULL,
+ .tx_fifomask = S5PV210_UFSTAT_TXMASK,
+ .tx_fifoshift = S5PV210_UFSTAT_TXSHIFT,
+ .def_clk_sel = S3C2410_UCON_CLKSEL0,
+ .num_clks = 2,
+ .clksel_mask = S5PV210_UCON_CLKMASK,
+ .clksel_shift = S5PV210_UCON_CLKSHIFT,
+ },
+ .def_cfg = &(struct s3c2410_uartcfg) {
+ .ucon = S5PV210_UCON_DEFAULT,
+ .ufcon = S5PV210_UFCON_DEFAULT,
+ },
+ .fifosize = { 256, 64, 16, 16 },
+};
+#define S5PV210_SERIAL_DRV_DATA ((kernel_ulong_t)&s5pv210_serial_drv_data)
+#else
+#define S5PV210_SERIAL_DRV_DATA (kernel_ulong_t)NULL
+#endif
- if (strcmp(dev->name, drv->driver.name) != 0)
- return 0;
+#ifdef CONFIG_CPU_EXYNOS4210
+static struct s3c24xx_serial_drv_data exynos4210_serial_drv_data = {
+ .info = &(struct s3c24xx_uart_info) {
+ .name = "Samsung Exynos4 UART",
+ .type = PORT_S3C6400,
+ .has_divslot = 1,
+ .rx_fifomask = S5PV210_UFSTAT_RXMASK,
+ .rx_fifoshift = S5PV210_UFSTAT_RXSHIFT,
+ .rx_fifofull = S5PV210_UFSTAT_RXFULL,
+ .tx_fifofull = S5PV210_UFSTAT_TXFULL,
+ .tx_fifomask = S5PV210_UFSTAT_TXMASK,
+ .tx_fifoshift = S5PV210_UFSTAT_TXSHIFT,
+ .def_clk_sel = S3C2410_UCON_CLKSEL0,
+ .num_clks = 1,
+ .clksel_mask = 0,
+ .clksel_shift = 0,
+ },
+ .def_cfg = &(struct s3c2410_uartcfg) {
+ .ucon = S5PV210_UCON_DEFAULT,
+ .ufcon = S5PV210_UFCON_DEFAULT,
+ .has_fracval = 1,
+ },
+ .fifosize = { 256, 64, 16, 16 },
+};
+#define EXYNOS4210_SERIAL_DRV_DATA ((kernel_ulong_t)&exynos4210_serial_drv_data)
+#else
+#define EXYNOS4210_SERIAL_DRV_DATA (kernel_ulong_t)NULL
+#endif
- s3c24xx_serial_console.data = &s3c24xx_uart_drv;
- s3c24xx_serial_init_ports(info);
+static struct platform_device_id s3c24xx_serial_driver_ids[] = {
+ {
+ .name = "s3c2410-uart",
+ .driver_data = S3C2410_SERIAL_DRV_DATA,
+ }, {
+ .name = "s3c2412-uart",
+ .driver_data = S3C2412_SERIAL_DRV_DATA,
+ }, {
+ .name = "s3c2440-uart",
+ .driver_data = S3C2440_SERIAL_DRV_DATA,
+ }, {
+ .name = "s3c6400-uart",
+ .driver_data = S3C6400_SERIAL_DRV_DATA,
+ }, {
+ .name = "s5pv210-uart",
+ .driver_data = S5PV210_SERIAL_DRV_DATA,
+ }, {
+ .name = "exynos4210-uart",
+ .driver_data = EXYNOS4210_SERIAL_DRV_DATA,
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(platform, s3c24xx_serial_driver_ids);
- register_console(&s3c24xx_serial_console);
- return 0;
+#ifdef CONFIG_OF
+static const struct of_device_id s3c24xx_uart_dt_match[] = {
+ { .compatible = "samsung,exynos4210-uart",
+ .data = (void *)EXYNOS4210_SERIAL_DRV_DATA },
+ {},
+};
+MODULE_DEVICE_TABLE(of, s3c24xx_uart_dt_match);
+#else
+#define s3c24xx_uart_dt_match NULL
+#endif
+
+static struct platform_driver samsung_serial_driver = {
+ .probe = s3c24xx_serial_probe,
+ .remove = __devexit_p(s3c24xx_serial_remove),
+ .id_table = s3c24xx_serial_driver_ids,
+ .driver = {
+ .name = "samsung-uart",
+ .owner = THIS_MODULE,
+ .pm = SERIAL_SAMSUNG_PM_OPS,
+ .of_match_table = s3c24xx_uart_dt_match,
+ },
+};
+
+/* module initialisation code */
+
+static int __init s3c24xx_serial_modinit(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&s3c24xx_uart_drv);
+ if (ret < 0) {
+ printk(KERN_ERR "failed to register UART driver\n");
+ return -1;
+ }
+
+ return platform_driver_register(&samsung_serial_driver);
}
-#endif /* CONFIG_SERIAL_SAMSUNG_CONSOLE */
+static void __exit s3c24xx_serial_modexit(void)
+{
+ uart_unregister_driver(&s3c24xx_uart_drv);
+}
+
+module_init(s3c24xx_serial_modinit);
+module_exit(s3c24xx_serial_modexit);
+MODULE_ALIAS("platform:samsung-uart");
MODULE_DESCRIPTION("Samsung SoC Serial port driver");
MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
MODULE_LICENSE("GPL v2");
unsigned long tx_fifomask;
unsigned long tx_fifoshift;
unsigned long tx_fifofull;
+ unsigned int def_clk_sel;
+ unsigned long num_clks;
+ unsigned long clksel_mask;
+ unsigned long clksel_shift;
/* uart port features */
unsigned int has_divslot:1;
- /* clock source control */
-
- int (*get_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk);
- int (*set_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk);
-
/* uart controls */
int (*reset_port)(struct uart_port *, struct s3c2410_uartcfg *);
};
+struct s3c24xx_serial_drv_data {
+ struct s3c24xx_uart_info *info;
+ struct s3c2410_uartcfg *def_cfg;
+ unsigned int fifosize[CONFIG_SERIAL_SAMSUNG_UARTS];
+};
+
struct s3c24xx_uart_port {
unsigned char rx_claimed;
unsigned char tx_claimed;
unsigned int tx_irq;
struct s3c24xx_uart_info *info;
- struct s3c24xx_uart_clksrc *clksrc;
struct clk *clk;
struct clk *baudclk;
struct uart_port port;
+ struct s3c24xx_serial_drv_data *drv_data;
+
+ /* reference to platform data */
+ struct s3c2410_uartcfg *cfg;
#ifdef CONFIG_CPU_FREQ
struct notifier_block freq_transition;
/* conversion functions */
#define s3c24xx_dev_to_port(__dev) (struct uart_port *)dev_get_drvdata(__dev)
-#define s3c24xx_dev_to_cfg(__dev) (struct s3c2410_uartcfg *)((__dev)->platform_data)
/* register access controls */
#define wr_regb(port, reg, val) __raw_writeb(val, portaddr(port, reg))
#define wr_regl(port, reg, val) __raw_writel(val, portaddr(port, reg))
-extern int s3c24xx_serial_probe(struct platform_device *dev,
- struct s3c24xx_uart_info *uart);
-
-extern int __devexit s3c24xx_serial_remove(struct platform_device *dev);
-
-extern int s3c24xx_serial_initconsole(struct platform_driver *drv,
- struct s3c24xx_uart_info **uart);
-
-extern int s3c24xx_serial_init(struct platform_driver *drv,
- struct s3c24xx_uart_info *info);
-
#ifdef CONFIG_SERIAL_SAMSUNG_DEBUG
extern void printascii(const char *);
#ifndef __AMBA_PL330_H_
#define __AMBA_PL330_H_
+#include <linux/dmaengine.h>
#include <asm/hardware/pl330.h>
-struct dma_pl330_peri {
- /*
- * Peri_Req i/f of the DMAC that is
- * peripheral could be reached from.
- */
- u8 peri_id; /* specific dma id */
- enum pl330_reqtype rqtype;
-};
-
struct dma_pl330_platdata {
/*
* Number of valid peripherals connected to DMAC.
*/
u8 nr_valid_peri;
/* Array of valid peripherals */
- struct dma_pl330_peri *peri;
+ u8 *peri_id;
+ /* Operational capabilities */
+ dma_cap_mask_t cap_mask;
/* Bytes to allocate for MC buffer */
unsigned mcbuf_sz;
};
+extern bool pl330_filter(struct dma_chan *chan, void *param);
#endif /* __AMBA_PL330_H_ */
projects / firefly-linux-kernel-4.4.55.git / commitdiff