#include <linux/hardirq.h>
#include <linux/delay.h>
#include <linux/of_device.h>
+#include <linux/of_mdio.h>
#include <linux/of_platform.h>
#include <linux/netdevice.h>
#define DRIVER_NAME "mpc52xx-fec"
-#define FEC5200_PHYADDR_NONE (-1)
-#define FEC5200_PHYADDR_7WIRE (-2)
-
/* Private driver data structure */
struct mpc52xx_fec_priv {
+ struct net_device *ndev;
int duplex;
int speed;
int r_irq;
int msg_enable;
/* MDIO link details */
- int phy_addr;
- unsigned int phy_speed;
+ unsigned int mdio_speed;
+ struct device_node *phy_node;
struct phy_device *phydev;
enum phy_state link;
+ int seven_wire_mode;
};
phy_print_status(phydev);
}
-static int mpc52xx_fec_init_phy(struct net_device *dev)
-{
- struct mpc52xx_fec_priv *priv = netdev_priv(dev);
- struct phy_device *phydev;
- char phy_id[BUS_ID_SIZE];
-
- snprintf(phy_id, sizeof(phy_id), "%x:%02x",
- (unsigned int)dev->base_addr, priv->phy_addr);
-
- priv->link = PHY_DOWN;
- priv->speed = 0;
- priv->duplex = -1;
-
- phydev = phy_connect(dev, phy_id, &mpc52xx_fec_adjust_link, 0, PHY_INTERFACE_MODE_MII);
- if (IS_ERR(phydev)) {
- dev_err(&dev->dev, "phy_connect failed\n");
- return PTR_ERR(phydev);
- }
- dev_info(&dev->dev, "attached phy %i to driver %s\n",
- phydev->addr, phydev->drv->name);
-
- priv->phydev = phydev;
-
- return 0;
-}
-
-static int mpc52xx_fec_phy_start(struct net_device *dev)
-{
- struct mpc52xx_fec_priv *priv = netdev_priv(dev);
- int err;
-
- if (priv->phy_addr < 0)
- return 0;
-
- err = mpc52xx_fec_init_phy(dev);
- if (err) {
- dev_err(&dev->dev, "mpc52xx_fec_init_phy failed\n");
- return err;
- }
-
- /* reset phy - this also wakes it from PDOWN */
- phy_write(priv->phydev, MII_BMCR, BMCR_RESET);
- phy_start(priv->phydev);
-
- return 0;
-}
-
-static void mpc52xx_fec_phy_stop(struct net_device *dev)
-{
- struct mpc52xx_fec_priv *priv = netdev_priv(dev);
-
- if (!priv->phydev)
- return;
-
- phy_disconnect(priv->phydev);
- /* power down phy */
- phy_stop(priv->phydev);
- phy_write(priv->phydev, MII_BMCR, BMCR_PDOWN);
-}
-
-static void mpc52xx_fec_phy_hw_init(struct mpc52xx_fec_priv *priv)
-{
- struct mpc52xx_fec __iomem *fec = priv->fec;
-
- if (priv->phydev)
- return;
-
- out_be32(&fec->mii_speed, priv->phy_speed);
-}
-
static int mpc52xx_fec_open(struct net_device *dev)
{
struct mpc52xx_fec_priv *priv = netdev_priv(dev);
int err = -EBUSY;
+ if (priv->phy_node) {
+ priv->phydev = of_phy_connect(priv->ndev, priv->phy_node,
+ mpc52xx_fec_adjust_link, 0, 0);
+ if (!priv->phydev) {
+ dev_err(&dev->dev, "of_phy_connect failed\n");
+ return -ENODEV;
+ }
+ phy_start(priv->phydev);
+ }
+
if (request_irq(dev->irq, &mpc52xx_fec_interrupt, IRQF_SHARED,
DRIVER_NAME "_ctrl", dev)) {
dev_err(&dev->dev, "ctrl interrupt request failed\n");
- goto out;
+ goto free_phy;
}
if (request_irq(priv->r_irq, &mpc52xx_fec_rx_interrupt, 0,
DRIVER_NAME "_rx", dev)) {
goto free_irqs;
}
- err = mpc52xx_fec_phy_start(dev);
- if (err)
- goto free_skbs;
-
bcom_enable(priv->rx_dmatsk);
bcom_enable(priv->tx_dmatsk);
return 0;
- free_skbs:
- mpc52xx_fec_free_rx_buffers(dev, priv->rx_dmatsk);
-
free_irqs:
free_irq(priv->t_irq, dev);
free_2irqs:
free_irq(priv->r_irq, dev);
free_ctrl_irq:
free_irq(dev->irq, dev);
- out:
+ free_phy:
+ if (priv->phydev) {
+ phy_stop(priv->phydev);
+ phy_disconnect(priv->phydev);
+ priv->phydev = NULL;
+ }
return err;
}
free_irq(priv->r_irq, dev);
free_irq(priv->t_irq, dev);
- mpc52xx_fec_phy_stop(dev);
+ if (priv->phydev) {
+ /* power down phy */
+ phy_stop(priv->phydev);
+ phy_disconnect(priv->phydev);
+ priv->phydev = NULL;
+ }
return 0;
}
/* set phy speed.
* this can't be done in phy driver, since it needs to be called
* before fec stuff (even on resume) */
- mpc52xx_fec_phy_hw_init(priv);
+ out_be32(&fec->mii_speed, priv->mdio_speed);
}
/**
rcntrl = FEC_RX_BUFFER_SIZE << 16; /* max frame length */
rcntrl |= FEC_RCNTRL_FCE;
- if (priv->phy_addr != FEC5200_PHYADDR_7WIRE)
+ if (!priv->seven_wire_mode)
rcntrl |= FEC_RCNTRL_MII_MODE;
if (priv->duplex == DUPLEX_FULL)
/* Stop FEC */
out_be32(&fec->ecntrl, in_be32(&fec->ecntrl) & ~FEC_ECNTRL_ETHER_EN);
-
- return;
}
/* reset fec and bestcomm tasks */
mpc52xx_fec_hw_init(dev);
- phy_stop(priv->phydev);
- phy_write(priv->phydev, MII_BMCR, BMCR_RESET);
- phy_start(priv->phydev);
+ if (priv->phydev) {
+ phy_stop(priv->phydev);
+ phy_write(priv->phydev, MII_BMCR, BMCR_RESET);
+ phy_start(priv->phydev);
+ }
bcom_fec_rx_reset(priv->rx_dmatsk);
bcom_fec_tx_reset(priv->tx_dmatsk);
struct net_device *ndev;
struct mpc52xx_fec_priv *priv = NULL;
struct resource mem;
- struct device_node *phy_node;
- const phandle *phy_handle;
const u32 *prop;
int prop_size;
return -ENOMEM;
priv = netdev_priv(ndev);
+ priv->ndev = ndev;
/* Reserve FEC control zone */
rv = of_address_to_resource(op->node, 0, &mem);
ndev->ethtool_ops = &mpc52xx_fec_ethtool_ops;
ndev->watchdog_timeo = FEC_WATCHDOG_TIMEOUT;
ndev->base_addr = mem.start;
+ SET_NETDEV_DEV(ndev, &op->dev);
spin_lock_init(&priv->lock);
*/
/* Start with safe defaults for link connection */
- priv->phy_addr = FEC5200_PHYADDR_NONE;
priv->speed = 100;
priv->duplex = DUPLEX_HALF;
- priv->mdio_speed = ((mpc52xx_find_ipb_freq(op->node) >> 20) / 5) << 1;
- priv->phy_speed = ((mpc5xxx_get_bus_frequency(op->node) >> 20) / 5) << 1;
-
- /* the 7-wire property means don't use MII mode */
- if (of_find_property(op->node, "fsl,7-wire-mode", NULL))
- priv->phy_addr = FEC5200_PHYADDR_7WIRE;
++ priv->mdio_speed = ((mpc5xxx_get_bus_frequency(op->node) >> 20) / 5) << 1;
/* The current speed preconfigures the speed of the MII link */
prop = of_get_property(op->node, "current-speed", &prop_size);
priv->duplex = prop[1] ? DUPLEX_FULL : DUPLEX_HALF;
}
- /* If there is a phy handle, setup link to that phy */
- phy_handle = of_get_property(op->node, "phy-handle", &prop_size);
- if (phy_handle && (prop_size >= sizeof(phandle))) {
- phy_node = of_find_node_by_phandle(*phy_handle);
- prop = of_get_property(phy_node, "reg", &prop_size);
- if (prop && (prop_size >= sizeof(u32)))
- if ((*prop >= 0) && (*prop < PHY_MAX_ADDR))
- priv->phy_addr = *prop;
- of_node_put(phy_node);
+ /* If there is a phy handle, then get the PHY node */
+ priv->phy_node = of_parse_phandle(op->node, "phy-handle", 0);
+
+ /* the 7-wire property means don't use MII mode */
+ if (of_find_property(op->node, "fsl,7-wire-mode", NULL)) {
+ priv->seven_wire_mode = 1;
+ dev_info(&ndev->dev, "using 7-wire PHY mode\n");
}
/* Hardware init */
mpc52xx_fec_hw_init(ndev);
-
mpc52xx_fec_reset_stats(ndev);
- SET_NETDEV_DEV(ndev, &op->dev);
-
- /* Register the new network device */
rv = register_netdev(ndev);
if (rv < 0)
goto probe_error;
- /* Now report the link setup */
- switch (priv->phy_addr) {
- case FEC5200_PHYADDR_NONE:
- dev_info(&ndev->dev, "Fixed speed MII link: %i%cD\n",
- priv->speed, priv->duplex ? 'F' : 'H');
- break;
- case FEC5200_PHYADDR_7WIRE:
- dev_info(&ndev->dev, "using 7-wire PHY mode\n");
- break;
- default:
- dev_info(&ndev->dev, "Using PHY at MDIO address %i\n",
- priv->phy_addr);
- }
-
/* We're done ! */
dev_set_drvdata(&op->dev, ndev);
/* Error handling - free everything that might be allocated */
probe_error:
+ if (priv->phy_node)
+ of_node_put(priv->phy_node);
+ priv->phy_node = NULL;
+
irq_dispose_mapping(ndev->irq);
if (priv->rx_dmatsk)
unregister_netdev(ndev);
+ if (priv->phy_node)
+ of_node_put(priv->phy_node);
+ priv->phy_node = NULL;
+
irq_dispose_mapping(ndev->irq);
bcom_fec_rx_release(priv->rx_dmatsk);
#include <linux/netdevice.h>
#include <linux/phy.h>
#include <linux/of_platform.h>
+#include <linux/of_mdio.h>
#include <asm/io.h>
#include <asm/mpc52xx.h>
#include "fec_mpc52xx.h"
struct mpc52xx_fec_mdio_priv {
struct mpc52xx_fec __iomem *regs;
+ int mdio_irqs[PHY_MAX_ADDR];
};
static int mpc52xx_fec_mdio_transfer(struct mii_bus *bus, int phy_id,
{
struct mpc52xx_fec_mdio_priv *priv = bus->priv;
struct mpc52xx_fec __iomem *fec;
- int tries = 100;
+ int tries = 3;
value |= (phy_id << FEC_MII_DATA_PA_SHIFT) & FEC_MII_DATA_PA_MSK;
value |= (reg << FEC_MII_DATA_RA_SHIFT) & FEC_MII_DATA_RA_MSK;
/* wait for it to finish, this takes about 23 us on lite5200b */
while (!(in_be32(&fec->ievent) & FEC_IEVENT_MII) && --tries)
- udelay(5);
+ msleep(1);
if (!tries)
return -ETIMEDOUT;
{
struct device *dev = &of->dev;
struct device_node *np = of->node;
- struct device_node *child = NULL;
struct mii_bus *bus;
struct mpc52xx_fec_mdio_priv *priv;
struct resource res = {};
bus->write = mpc52xx_fec_mdio_write;
/* setup irqs */
- bus->irq = kmalloc(sizeof(bus->irq[0]) * PHY_MAX_ADDR, GFP_KERNEL);
- if (bus->irq == NULL) {
- err = -ENOMEM;
- goto out_free;
- }
- for (i=0; i<PHY_MAX_ADDR; i++)
- bus->irq[i] = PHY_POLL;
-
- while ((child = of_get_next_child(np, child)) != NULL) {
- int irq = irq_of_parse_and_map(child, 0);
- if (irq != NO_IRQ) {
- const u32 *id = of_get_property(child, "reg", NULL);
- if (id)
- bus->irq[*id] = irq;
- }
- }
+ bus->irq = priv->mdio_irqs;
/* setup registers */
err = of_address_to_resource(np, 0, &res);
/* set MII speed */
out_be32(&priv->regs->mii_speed,
- ((mpc52xx_find_ipb_freq(of->node) >> 20) / 5) << 1);
+ ((mpc5xxx_get_bus_frequency(of->node) >> 20) / 5) << 1);
- err = mdiobus_register(bus);
+ err = of_mdiobus_register(bus, np);
if (err)
goto out_unmap;
projects / firefly-linux-kernel-4.4.55.git / commitdiff