+++ /dev/null
- Dynamic DMA mapping
- ===================
-
- David S. Miller <davem@redhat.com>
- Richard Henderson <rth@cygnus.com>
- Jakub Jelinek <jakub@redhat.com>
-
-This document describes the DMA mapping system in terms of the pci_
-API. For a similar API that works for generic devices, see
-DMA-API.txt.
-
-Most of the 64bit platforms have special hardware that translates bus
-addresses (DMA addresses) into physical addresses. This is similar to
-how page tables and/or a TLB translates virtual addresses to physical
-addresses on a CPU. This is needed so that e.g. PCI devices can
-access with a Single Address Cycle (32bit DMA address) any page in the
-64bit physical address space. Previously in Linux those 64bit
-platforms had to set artificial limits on the maximum RAM size in the
-system, so that the virt_to_bus() static scheme works (the DMA address
-translation tables were simply filled on bootup to map each bus
-address to the physical page __pa(bus_to_virt())).
-
-So that Linux can use the dynamic DMA mapping, it needs some help from the
-drivers, namely it has to take into account that DMA addresses should be
-mapped only for the time they are actually used and unmapped after the DMA
-transfer.
-
-The following API will work of course even on platforms where no such
-hardware exists, see e.g. arch/x86/include/asm/pci.h for how it is implemented on
-top of the virt_to_bus interface.
-
-First of all, you should make sure
-
-#include <linux/pci.h>
-
-is in your driver. This file will obtain for you the definition of the
-dma_addr_t (which can hold any valid DMA address for the platform)
-type which should be used everywhere you hold a DMA (bus) address
-returned from the DMA mapping functions.
-
- What memory is DMA'able?
-
-The first piece of information you must know is what kernel memory can
-be used with the DMA mapping facilities. There has been an unwritten
-set of rules regarding this, and this text is an attempt to finally
-write them down.
-
-If you acquired your memory via the page allocator
-(i.e. __get_free_page*()) or the generic memory allocators
-(i.e. kmalloc() or kmem_cache_alloc()) then you may DMA to/from
-that memory using the addresses returned from those routines.
-
-This means specifically that you may _not_ use the memory/addresses
-returned from vmalloc() for DMA. It is possible to DMA to the
-_underlying_ memory mapped into a vmalloc() area, but this requires
-walking page tables to get the physical addresses, and then
-translating each of those pages back to a kernel address using
-something like __va(). [ EDIT: Update this when we integrate
-Gerd Knorr's generic code which does this. ]
-
-This rule also means that you may use neither kernel image addresses
-(items in data/text/bss segments), nor module image addresses, nor
-stack addresses for DMA. These could all be mapped somewhere entirely
-different than the rest of physical memory. Even if those classes of
-memory could physically work with DMA, you'd need to ensure the I/O
-buffers were cacheline-aligned. Without that, you'd see cacheline
-sharing problems (data corruption) on CPUs with DMA-incoherent caches.
-(The CPU could write to one word, DMA would write to a different one
-in the same cache line, and one of them could be overwritten.)
-
-Also, this means that you cannot take the return of a kmap()
-call and DMA to/from that. This is similar to vmalloc().
-
-What about block I/O and networking buffers? The block I/O and
-networking subsystems make sure that the buffers they use are valid
-for you to DMA from/to.
-
- DMA addressing limitations
-
-Does your device have any DMA addressing limitations? For example, is
-your device only capable of driving the low order 24-bits of address
-on the PCI bus for SAC DMA transfers? If so, you need to inform the
-PCI layer of this fact.
-
-By default, the kernel assumes that your device can address the full
-32-bits in a SAC cycle. For a 64-bit DAC capable device, this needs
-to be increased. And for a device with limitations, as discussed in
-the previous paragraph, it needs to be decreased.
-
-pci_alloc_consistent() by default will return 32-bit DMA addresses.
-PCI-X specification requires PCI-X devices to support 64-bit
-addressing (DAC) for all transactions. And at least one platform (SGI
-SN2) requires 64-bit consistent allocations to operate correctly when
-the IO bus is in PCI-X mode. Therefore, like with pci_set_dma_mask(),
-it's good practice to call pci_set_consistent_dma_mask() to set the
-appropriate mask even if your device only supports 32-bit DMA
-(default) and especially if it's a PCI-X device.
-
-For correct operation, you must interrogate the PCI layer in your
-device probe routine to see if the PCI controller on the machine can
-properly support the DMA addressing limitation your device has. It is
-good style to do this even if your device holds the default setting,
-because this shows that you did think about these issues wrt. your
-device.
-
-The query is performed via a call to pci_set_dma_mask():
-
- int pci_set_dma_mask(struct pci_dev *pdev, u64 device_mask);
-
-The query for consistent allocations is performed via a call to
-pci_set_consistent_dma_mask():
-
- int pci_set_consistent_dma_mask(struct pci_dev *pdev, u64 device_mask);
-
-Here, pdev is a pointer to the PCI device struct of your device, and
-device_mask is a bit mask describing which bits of a PCI address your
-device supports. It returns zero if your card can perform DMA
-properly on the machine given the address mask you provided.
-
-If it returns non-zero, your device cannot perform DMA properly on
-this platform, and attempting to do so will result in undefined
-behavior. You must either use a different mask, or not use DMA.
-
-This means that in the failure case, you have three options:
-
-1) Use another DMA mask, if possible (see below).
-2) Use some non-DMA mode for data transfer, if possible.
-3) Ignore this device and do not initialize it.
-
-It is recommended that your driver print a kernel KERN_WARNING message
-when you end up performing either #2 or #3. In this manner, if a user
-of your driver reports that performance is bad or that the device is not
-even detected, you can ask them for the kernel messages to find out
-exactly why.
-
-The standard 32-bit addressing PCI device would do something like
-this:
-
- if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
- printk(KERN_WARNING
- "mydev: No suitable DMA available.\n");
- goto ignore_this_device;
- }
-
-Another common scenario is a 64-bit capable device. The approach
-here is to try for 64-bit DAC addressing, but back down to a
-32-bit mask should that fail. The PCI platform code may fail the
-64-bit mask not because the platform is not capable of 64-bit
-addressing. Rather, it may fail in this case simply because
-32-bit SAC addressing is done more efficiently than DAC addressing.
-Sparc64 is one platform which behaves in this way.
-
-Here is how you would handle a 64-bit capable device which can drive
-all 64-bits when accessing streaming DMA:
-
- int using_dac;
-
- if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
- using_dac = 1;
- } else if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
- using_dac = 0;
- } else {
- printk(KERN_WARNING
- "mydev: No suitable DMA available.\n");
- goto ignore_this_device;
- }
-
-If a card is capable of using 64-bit consistent allocations as well,
-the case would look like this:
-
- int using_dac, consistent_using_dac;
-
- if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
- using_dac = 1;
- consistent_using_dac = 1;
- pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
- } else if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
- using_dac = 0;
- consistent_using_dac = 0;
- pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
- } else {
- printk(KERN_WARNING
- "mydev: No suitable DMA available.\n");
- goto ignore_this_device;
- }
-
-pci_set_consistent_dma_mask() will always be able to set the same or a
-smaller mask as pci_set_dma_mask(). However for the rare case that a
-device driver only uses consistent allocations, one would have to
-check the return value from pci_set_consistent_dma_mask().
-
-Finally, if your device can only drive the low 24-bits of
-address during PCI bus mastering you might do something like:
-
- if (pci_set_dma_mask(pdev, DMA_BIT_MASK(24))) {
- printk(KERN_WARNING
- "mydev: 24-bit DMA addressing not available.\n");
- goto ignore_this_device;
- }
-
-When pci_set_dma_mask() is successful, and returns zero, the PCI layer
-saves away this mask you have provided. The PCI layer will use this
-information later when you make DMA mappings.
-
-There is a case which we are aware of at this time, which is worth
-mentioning in this documentation. If your device supports multiple
-functions (for example a sound card provides playback and record
-functions) and the various different functions have _different_
-DMA addressing limitations, you may wish to probe each mask and
-only provide the functionality which the machine can handle. It
-is important that the last call to pci_set_dma_mask() be for the
-most specific mask.
-
-Here is pseudo-code showing how this might be done:
-
- #define PLAYBACK_ADDRESS_BITS DMA_BIT_MASK(32)
- #define RECORD_ADDRESS_BITS DMA_BIT_MASK(24)
-
- struct my_sound_card *card;
- struct pci_dev *pdev;
-
- ...
- if (!pci_set_dma_mask(pdev, PLAYBACK_ADDRESS_BITS)) {
- card->playback_enabled = 1;
- } else {
- card->playback_enabled = 0;
- printk(KERN_WARNING "%s: Playback disabled due to DMA limitations.\n",
- card->name);
- }
- if (!pci_set_dma_mask(pdev, RECORD_ADDRESS_BITS)) {
- card->record_enabled = 1;
- } else {
- card->record_enabled = 0;
- printk(KERN_WARNING "%s: Record disabled due to DMA limitations.\n",
- card->name);
- }
-
-A sound card was used as an example here because this genre of PCI
-devices seems to be littered with ISA chips given a PCI front end,
-and thus retaining the 16MB DMA addressing limitations of ISA.
-
- Types of DMA mappings
-
-There are two types of DMA mappings:
-
-- Consistent DMA mappings which are usually mapped at driver
- initialization, unmapped at the end and for which the hardware should
- guarantee that the device and the CPU can access the data
- in parallel and will see updates made by each other without any
- explicit software flushing.
-
- Think of "consistent" as "synchronous" or "coherent".
-
- The current default is to return consistent memory in the low 32
- bits of the PCI bus space. However, for future compatibility you
- should set the consistent mask even if this default is fine for your
- driver.
-
- Good examples of what to use consistent mappings for are:
-
- - Network card DMA ring descriptors.
- - SCSI adapter mailbox command data structures.
- - Device firmware microcode executed out of
- main memory.
-
- The invariant these examples all require is that any CPU store
- to memory is immediately visible to the device, and vice
- versa. Consistent mappings guarantee this.
-
- IMPORTANT: Consistent DMA memory does not preclude the usage of
- proper memory barriers. The CPU may reorder stores to
- consistent memory just as it may normal memory. Example:
- if it is important for the device to see the first word
- of a descriptor updated before the second, you must do
- something like:
-
- desc->word0 = address;
- wmb();
- desc->word1 = DESC_VALID;
-
- in order to get correct behavior on all platforms.
-
- Also, on some platforms your driver may need to flush CPU write
- buffers in much the same way as it needs to flush write buffers
- found in PCI bridges (such as by reading a register's value
- after writing it).
-
-- Streaming DMA mappings which are usually mapped for one DMA transfer,
- unmapped right after it (unless you use pci_dma_sync_* below) and for which
- hardware can optimize for sequential accesses.
-
- This of "streaming" as "asynchronous" or "outside the coherency
- domain".
-
- Good examples of what to use streaming mappings for are:
-
- - Networking buffers transmitted/received by a device.
- - Filesystem buffers written/read by a SCSI device.
-
- The interfaces for using this type of mapping were designed in
- such a way that an implementation can make whatever performance
- optimizations the hardware allows. To this end, when using
- such mappings you must be explicit about what you want to happen.
-
-Neither type of DMA mapping has alignment restrictions that come
-from PCI, although some devices may have such restrictions.
-Also, systems with caches that aren't DMA-coherent will work better
-when the underlying buffers don't share cache lines with other data.
-
-
- Using Consistent DMA mappings.
-
-To allocate and map large (PAGE_SIZE or so) consistent DMA regions,
-you should do:
-
- dma_addr_t dma_handle;
-
- cpu_addr = pci_alloc_consistent(pdev, size, &dma_handle);
-
-where pdev is a struct pci_dev *. This may be called in interrupt context.
-You should use dma_alloc_coherent (see DMA-API.txt) for buses
-where devices don't have struct pci_dev (like ISA, EISA).
-
-This argument is needed because the DMA translations may be bus
-specific (and often is private to the bus which the device is attached
-to).
-
-Size is the length of the region you want to allocate, in bytes.
-
-This routine will allocate RAM for that region, so it acts similarly to
-__get_free_pages (but takes size instead of a page order). If your
-driver needs regions sized smaller than a page, you may prefer using
-the pci_pool interface, described below.
-
-The consistent DMA mapping interfaces, for non-NULL pdev, will by
-default return a DMA address which is SAC (Single Address Cycle)
-addressable. Even if the device indicates (via PCI dma mask) that it
-may address the upper 32-bits and thus perform DAC cycles, consistent
-allocation will only return > 32-bit PCI addresses for DMA if the
-consistent dma mask has been explicitly changed via
-pci_set_consistent_dma_mask(). This is true of the pci_pool interface
-as well.
-
-pci_alloc_consistent returns two values: the virtual address which you
-can use to access it from the CPU and dma_handle which you pass to the
-card.
-
-The cpu return address and the DMA bus master address are both
-guaranteed to be aligned to the smallest PAGE_SIZE order which
-is greater than or equal to the requested size. This invariant
-exists (for example) to guarantee that if you allocate a chunk
-which is smaller than or equal to 64 kilobytes, the extent of the
-buffer you receive will not cross a 64K boundary.
-
-To unmap and free such a DMA region, you call:
-
- pci_free_consistent(pdev, size, cpu_addr, dma_handle);
-
-where pdev, size are the same as in the above call and cpu_addr and
-dma_handle are the values pci_alloc_consistent returned to you.
-This function may not be called in interrupt context.
-
-If your driver needs lots of smaller memory regions, you can write
-custom code to subdivide pages returned by pci_alloc_consistent,
-or you can use the pci_pool API to do that. A pci_pool is like
-a kmem_cache, but it uses pci_alloc_consistent not __get_free_pages.
-Also, it understands common hardware constraints for alignment,
-like queue heads needing to be aligned on N byte boundaries.
-
-Create a pci_pool like this:
-
- struct pci_pool *pool;
-
- pool = pci_pool_create(name, pdev, size, align, alloc);
-
-The "name" is for diagnostics (like a kmem_cache name); pdev and size
-are as above. The device's hardware alignment requirement for this
-type of data is "align" (which is expressed in bytes, and must be a
-power of two). If your device has no boundary crossing restrictions,
-pass 0 for alloc; passing 4096 says memory allocated from this pool
-must not cross 4KByte boundaries (but at that time it may be better to
-go for pci_alloc_consistent directly instead).
-
-Allocate memory from a pci pool like this:
-
- cpu_addr = pci_pool_alloc(pool, flags, &dma_handle);
-
-flags are SLAB_KERNEL if blocking is permitted (not in_interrupt nor
-holding SMP locks), SLAB_ATOMIC otherwise. Like pci_alloc_consistent,
-this returns two values, cpu_addr and dma_handle.
-
-Free memory that was allocated from a pci_pool like this:
-
- pci_pool_free(pool, cpu_addr, dma_handle);
-
-where pool is what you passed to pci_pool_alloc, and cpu_addr and
-dma_handle are the values pci_pool_alloc returned. This function
-may be called in interrupt context.
-
-Destroy a pci_pool by calling:
-
- pci_pool_destroy(pool);
-
-Make sure you've called pci_pool_free for all memory allocated
-from a pool before you destroy the pool. This function may not
-be called in interrupt context.
-
- DMA Direction
-
-The interfaces described in subsequent portions of this document
-take a DMA direction argument, which is an integer and takes on
-one of the following values:
-
- PCI_DMA_BIDIRECTIONAL
- PCI_DMA_TODEVICE
- PCI_DMA_FROMDEVICE
- PCI_DMA_NONE
-
-One should provide the exact DMA direction if you know it.
-
-PCI_DMA_TODEVICE means "from main memory to the PCI device"
-PCI_DMA_FROMDEVICE means "from the PCI device to main memory"
-It is the direction in which the data moves during the DMA
-transfer.
-
-You are _strongly_ encouraged to specify this as precisely
-as you possibly can.
-
-If you absolutely cannot know the direction of the DMA transfer,
-specify PCI_DMA_BIDIRECTIONAL. It means that the DMA can go in
-either direction. The platform guarantees that you may legally
-specify this, and that it will work, but this may be at the
-cost of performance for example.
-
-The value PCI_DMA_NONE is to be used for debugging. One can
-hold this in a data structure before you come to know the
-precise direction, and this will help catch cases where your
-direction tracking logic has failed to set things up properly.
-
-Another advantage of specifying this value precisely (outside of
-potential platform-specific optimizations of such) is for debugging.
-Some platforms actually have a write permission boolean which DMA
-mappings can be marked with, much like page protections in the user
-program address space. Such platforms can and do report errors in the
-kernel logs when the PCI controller hardware detects violation of the
-permission setting.
-
-Only streaming mappings specify a direction, consistent mappings
-implicitly have a direction attribute setting of
-PCI_DMA_BIDIRECTIONAL.
-
-The SCSI subsystem tells you the direction to use in the
-'sc_data_direction' member of the SCSI command your driver is
-working on.
-
-For Networking drivers, it's a rather simple affair. For transmit
-packets, map/unmap them with the PCI_DMA_TODEVICE direction
-specifier. For receive packets, just the opposite, map/unmap them
-with the PCI_DMA_FROMDEVICE direction specifier.
-
- Using Streaming DMA mappings
-
-The streaming DMA mapping routines can be called from interrupt
-context. There are two versions of each map/unmap, one which will
-map/unmap a single memory region, and one which will map/unmap a
-scatterlist.
-
-To map a single region, you do:
-
- struct pci_dev *pdev = mydev->pdev;
- dma_addr_t dma_handle;
- void *addr = buffer->ptr;
- size_t size = buffer->len;
-
- dma_handle = pci_map_single(pdev, addr, size, direction);
-
-and to unmap it:
-
- pci_unmap_single(pdev, dma_handle, size, direction);
-
-You should call pci_unmap_single when the DMA activity is finished, e.g.
-from the interrupt which told you that the DMA transfer is done.
-
-Using cpu pointers like this for single mappings has a disadvantage,
-you cannot reference HIGHMEM memory in this way. Thus, there is a
-map/unmap interface pair akin to pci_{map,unmap}_single. These
-interfaces deal with page/offset pairs instead of cpu pointers.
-Specifically:
-
- struct pci_dev *pdev = mydev->pdev;
- dma_addr_t dma_handle;
- struct page *page = buffer->page;
- unsigned long offset = buffer->offset;
- size_t size = buffer->len;
-
- dma_handle = pci_map_page(pdev, page, offset, size, direction);
-
- ...
-
- pci_unmap_page(pdev, dma_handle, size, direction);
-
-Here, "offset" means byte offset within the given page.
-
-With scatterlists, you map a region gathered from several regions by:
-
- int i, count = pci_map_sg(pdev, sglist, nents, direction);
- struct scatterlist *sg;
-
- for_each_sg(sglist, sg, count, i) {
- hw_address[i] = sg_dma_address(sg);
- hw_len[i] = sg_dma_len(sg);
- }
-
-where nents is the number of entries in the sglist.
-
-The implementation is free to merge several consecutive sglist entries
-into one (e.g. if DMA mapping is done with PAGE_SIZE granularity, any
-consecutive sglist entries can be merged into one provided the first one
-ends and the second one starts on a page boundary - in fact this is a huge
-advantage for cards which either cannot do scatter-gather or have very
-limited number of scatter-gather entries) and returns the actual number
-of sg entries it mapped them to. On failure 0 is returned.
-
-Then you should loop count times (note: this can be less than nents times)
-and use sg_dma_address() and sg_dma_len() macros where you previously
-accessed sg->address and sg->length as shown above.
-
-To unmap a scatterlist, just call:
-
- pci_unmap_sg(pdev, sglist, nents, direction);
-
-Again, make sure DMA activity has already finished.
-
-PLEASE NOTE: The 'nents' argument to the pci_unmap_sg call must be
- the _same_ one you passed into the pci_map_sg call,
- it should _NOT_ be the 'count' value _returned_ from the
- pci_map_sg call.
-
-Every pci_map_{single,sg} call should have its pci_unmap_{single,sg}
-counterpart, because the bus address space is a shared resource (although
-in some ports the mapping is per each BUS so less devices contend for the
-same bus address space) and you could render the machine unusable by eating
-all bus addresses.
-
-If you need to use the same streaming DMA region multiple times and touch
-the data in between the DMA transfers, the buffer needs to be synced
-properly in order for the cpu and device to see the most uptodate and
-correct copy of the DMA buffer.
-
-So, firstly, just map it with pci_map_{single,sg}, and after each DMA
-transfer call either:
-
- pci_dma_sync_single_for_cpu(pdev, dma_handle, size, direction);
-
-or:
-
- pci_dma_sync_sg_for_cpu(pdev, sglist, nents, direction);
-
-as appropriate.
-
-Then, if you wish to let the device get at the DMA area again,
-finish accessing the data with the cpu, and then before actually
-giving the buffer to the hardware call either:
-
- pci_dma_sync_single_for_device(pdev, dma_handle, size, direction);
-
-or:
-
- pci_dma_sync_sg_for_device(dev, sglist, nents, direction);
-
-as appropriate.
-
-After the last DMA transfer call one of the DMA unmap routines
-pci_unmap_{single,sg}. If you don't touch the data from the first pci_map_*
-call till pci_unmap_*, then you don't have to call the pci_dma_sync_*
-routines at all.
-
-Here is pseudo code which shows a situation in which you would need
-to use the pci_dma_sync_*() interfaces.
-
- my_card_setup_receive_buffer(struct my_card *cp, char *buffer, int len)
- {
- dma_addr_t mapping;
-
- mapping = pci_map_single(cp->pdev, buffer, len, PCI_DMA_FROMDEVICE);
-
- cp->rx_buf = buffer;
- cp->rx_len = len;
- cp->rx_dma = mapping;
-
- give_rx_buf_to_card(cp);
- }
-
- ...
-
- my_card_interrupt_handler(int irq, void *devid, struct pt_regs *regs)
- {
- struct my_card *cp = devid;
-
- ...
- if (read_card_status(cp) == RX_BUF_TRANSFERRED) {
- struct my_card_header *hp;
-
- /* Examine the header to see if we wish
- * to accept the data. But synchronize
- * the DMA transfer with the CPU first
- * so that we see updated contents.
- */
- pci_dma_sync_single_for_cpu(cp->pdev, cp->rx_dma,
- cp->rx_len,
- PCI_DMA_FROMDEVICE);
-
- /* Now it is safe to examine the buffer. */
- hp = (struct my_card_header *) cp->rx_buf;
- if (header_is_ok(hp)) {
- pci_unmap_single(cp->pdev, cp->rx_dma, cp->rx_len,
- PCI_DMA_FROMDEVICE);
- pass_to_upper_layers(cp->rx_buf);
- make_and_setup_new_rx_buf(cp);
- } else {
- /* Just sync the buffer and give it back
- * to the card.
- */
- pci_dma_sync_single_for_device(cp->pdev,
- cp->rx_dma,
- cp->rx_len,
- PCI_DMA_FROMDEVICE);
- give_rx_buf_to_card(cp);
- }
- }
- }
-
-Drivers converted fully to this interface should not use virt_to_bus any
-longer, nor should they use bus_to_virt. Some drivers have to be changed a
-little bit, because there is no longer an equivalent to bus_to_virt in the
-dynamic DMA mapping scheme - you have to always store the DMA addresses
-returned by the pci_alloc_consistent, pci_pool_alloc, and pci_map_single
-calls (pci_map_sg stores them in the scatterlist itself if the platform
-supports dynamic DMA mapping in hardware) in your driver structures and/or
-in the card registers.
-
-All PCI drivers should be using these interfaces with no exceptions.
-It is planned to completely remove virt_to_bus() and bus_to_virt() as
-they are entirely deprecated. Some ports already do not provide these
-as it is impossible to correctly support them.
-
- Optimizing Unmap State Space Consumption
-
-On many platforms, pci_unmap_{single,page}() is simply a nop.
-Therefore, keeping track of the mapping address and length is a waste
-of space. Instead of filling your drivers up with ifdefs and the like
-to "work around" this (which would defeat the whole purpose of a
-portable API) the following facilities are provided.
-
-Actually, instead of describing the macros one by one, we'll
-transform some example code.
-
-1) Use DECLARE_PCI_UNMAP_{ADDR,LEN} in state saving structures.
- Example, before:
-
- struct ring_state {
- struct sk_buff *skb;
- dma_addr_t mapping;
- __u32 len;
- };
-
- after:
-
- struct ring_state {
- struct sk_buff *skb;
- DECLARE_PCI_UNMAP_ADDR(mapping)
- DECLARE_PCI_UNMAP_LEN(len)
- };
-
- NOTE: DO NOT put a semicolon at the end of the DECLARE_*()
- macro.
-
-2) Use pci_unmap_{addr,len}_set to set these values.
- Example, before:
-
- ringp->mapping = FOO;
- ringp->len = BAR;
-
- after:
-
- pci_unmap_addr_set(ringp, mapping, FOO);
- pci_unmap_len_set(ringp, len, BAR);
-
-3) Use pci_unmap_{addr,len} to access these values.
- Example, before:
-
- pci_unmap_single(pdev, ringp->mapping, ringp->len,
- PCI_DMA_FROMDEVICE);
-
- after:
-
- pci_unmap_single(pdev,
- pci_unmap_addr(ringp, mapping),
- pci_unmap_len(ringp, len),
- PCI_DMA_FROMDEVICE);
-
-It really should be self-explanatory. We treat the ADDR and LEN
-separately, because it is possible for an implementation to only
-need the address in order to perform the unmap operation.
-
- Platform Issues
-
-If you are just writing drivers for Linux and do not maintain
-an architecture port for the kernel, you can safely skip down
-to "Closing".
-
-1) Struct scatterlist requirements.
-
- Struct scatterlist must contain, at a minimum, the following
- members:
-
- struct page *page;
- unsigned int offset;
- unsigned int length;
-
- The base address is specified by a "page+offset" pair.
-
- Previous versions of struct scatterlist contained a "void *address"
- field that was sometimes used instead of page+offset. As of Linux
- 2.5., page+offset is always used, and the "address" field has been
- deleted.
-
-2) More to come...
-
- Handling Errors
-
-DMA address space is limited on some architectures and an allocation
-failure can be determined by:
-
-- checking if pci_alloc_consistent returns NULL or pci_map_sg returns 0
-
-- checking the returned dma_addr_t of pci_map_single and pci_map_page
- by using pci_dma_mapping_error():
-
- dma_addr_t dma_handle;
-
- dma_handle = pci_map_single(pdev, addr, size, direction);
- if (pci_dma_mapping_error(pdev, dma_handle)) {
- /*
- * reduce current DMA mapping usage,
- * delay and try again later or
- * reset driver.
- */
- }
-
- Closing
-
-This document, and the API itself, would not be in it's current
-form without the feedback and suggestions from numerous individuals.
-We would like to specifically mention, in no particular order, the
-following people:
-
- Russell King <rmk@arm.linux.org.uk>
- Leo Dagum <dagum@barrel.engr.sgi.com>
- Ralf Baechle <ralf@oss.sgi.com>
- Grant Grundler <grundler@cup.hp.com>
- Jay Estabrook <Jay.Estabrook@compaq.com>
- Thomas Sailer <sailer@ife.ee.ethz.ch>
- Andrea Arcangeli <andrea@suse.de>
- Jens Axboe <jens.axboe@oracle.com>
- David Mosberger-Tang <davidm@hpl.hp.com>
</para>
<programlisting>
static struct mtd_info *board_mtd;
-static unsigned long baseaddr;
+static void __iomem *baseaddr;
</programlisting>
<para>
Static example
<programlisting>
static struct mtd_info board_mtd;
static struct nand_chip board_chip;
-static unsigned long baseaddr;
+static void __iomem *baseaddr;
</programlisting>
</sect1>
<sect1 id="Partition_defines">
}
/* map physical address */
- baseaddr = (unsigned long)ioremap(CHIP_PHYSICAL_ADDRESS, 1024);
- if(!baseaddr){
+ baseaddr = ioremap(CHIP_PHYSICAL_ADDRESS, 1024);
+ if (!baseaddr) {
printk("Ioremap to access NAND chip failed\n");
err = -EIO;
goto out_mtd;
goto out;
out_ior:
- iounmap((void *)baseaddr);
+ iounmap(baseaddr);
out_mtd:
kfree (board_mtd);
out:
nand_release (board_mtd);
/* unmap physical address */
- iounmap((void *)baseaddr);
+ iounmap(baseaddr);
/* Free the MTD device structure */
kfree (board_mtd);
* access only the 640k-1MB area, so anything else
* has to be remapped.
*/
- char * baseptr = ioremap(0xFC000000, 1024*1024);
+ void __iomem *baseptr = ioremap(0xFC000000, 1024*1024);
/* write a 'A' to the offset 10 of the area */
writeb('A',baseptr+10);
--- /dev/null
+ Dynamic DMA mapping
+ ===================
+
+ David S. Miller <davem@redhat.com>
+ Richard Henderson <rth@cygnus.com>
+ Jakub Jelinek <jakub@redhat.com>
+
+This document describes the DMA mapping system in terms of the pci_
+API. For a similar API that works for generic devices, see
+DMA-API.txt.
+
+Most of the 64bit platforms have special hardware that translates bus
+addresses (DMA addresses) into physical addresses. This is similar to
+how page tables and/or a TLB translates virtual addresses to physical
+addresses on a CPU. This is needed so that e.g. PCI devices can
+access with a Single Address Cycle (32bit DMA address) any page in the
+64bit physical address space. Previously in Linux those 64bit
+platforms had to set artificial limits on the maximum RAM size in the
+system, so that the virt_to_bus() static scheme works (the DMA address
+translation tables were simply filled on bootup to map each bus
+address to the physical page __pa(bus_to_virt())).
+
+So that Linux can use the dynamic DMA mapping, it needs some help from the
+drivers, namely it has to take into account that DMA addresses should be
+mapped only for the time they are actually used and unmapped after the DMA
+transfer.
+
+The following API will work of course even on platforms where no such
+hardware exists, see e.g. arch/x86/include/asm/pci.h for how it is implemented on
+top of the virt_to_bus interface.
+
+First of all, you should make sure
+
+#include <linux/pci.h>
+
+is in your driver. This file will obtain for you the definition of the
+dma_addr_t (which can hold any valid DMA address for the platform)
+type which should be used everywhere you hold a DMA (bus) address
+returned from the DMA mapping functions.
+
+ What memory is DMA'able?
+
+The first piece of information you must know is what kernel memory can
+be used with the DMA mapping facilities. There has been an unwritten
+set of rules regarding this, and this text is an attempt to finally
+write them down.
+
+If you acquired your memory via the page allocator
+(i.e. __get_free_page*()) or the generic memory allocators
+(i.e. kmalloc() or kmem_cache_alloc()) then you may DMA to/from
+that memory using the addresses returned from those routines.
+
+This means specifically that you may _not_ use the memory/addresses
+returned from vmalloc() for DMA. It is possible to DMA to the
+_underlying_ memory mapped into a vmalloc() area, but this requires
+walking page tables to get the physical addresses, and then
+translating each of those pages back to a kernel address using
+something like __va(). [ EDIT: Update this when we integrate
+Gerd Knorr's generic code which does this. ]
+
+This rule also means that you may use neither kernel image addresses
+(items in data/text/bss segments), nor module image addresses, nor
+stack addresses for DMA. These could all be mapped somewhere entirely
+different than the rest of physical memory. Even if those classes of
+memory could physically work with DMA, you'd need to ensure the I/O
+buffers were cacheline-aligned. Without that, you'd see cacheline
+sharing problems (data corruption) on CPUs with DMA-incoherent caches.
+(The CPU could write to one word, DMA would write to a different one
+in the same cache line, and one of them could be overwritten.)
+
+Also, this means that you cannot take the return of a kmap()
+call and DMA to/from that. This is similar to vmalloc().
+
+What about block I/O and networking buffers? The block I/O and
+networking subsystems make sure that the buffers they use are valid
+for you to DMA from/to.
+
+ DMA addressing limitations
+
+Does your device have any DMA addressing limitations? For example, is
+your device only capable of driving the low order 24-bits of address
+on the PCI bus for SAC DMA transfers? If so, you need to inform the
+PCI layer of this fact.
+
+By default, the kernel assumes that your device can address the full
+32-bits in a SAC cycle. For a 64-bit DAC capable device, this needs
+to be increased. And for a device with limitations, as discussed in
+the previous paragraph, it needs to be decreased.
+
+pci_alloc_consistent() by default will return 32-bit DMA addresses.
+PCI-X specification requires PCI-X devices to support 64-bit
+addressing (DAC) for all transactions. And at least one platform (SGI
+SN2) requires 64-bit consistent allocations to operate correctly when
+the IO bus is in PCI-X mode. Therefore, like with pci_set_dma_mask(),
+it's good practice to call pci_set_consistent_dma_mask() to set the
+appropriate mask even if your device only supports 32-bit DMA
+(default) and especially if it's a PCI-X device.
+
+For correct operation, you must interrogate the PCI layer in your
+device probe routine to see if the PCI controller on the machine can
+properly support the DMA addressing limitation your device has. It is
+good style to do this even if your device holds the default setting,
+because this shows that you did think about these issues wrt. your
+device.
+
+The query is performed via a call to pci_set_dma_mask():
+
+ int pci_set_dma_mask(struct pci_dev *pdev, u64 device_mask);
+
+The query for consistent allocations is performed via a call to
+pci_set_consistent_dma_mask():
+
+ int pci_set_consistent_dma_mask(struct pci_dev *pdev, u64 device_mask);
+
+Here, pdev is a pointer to the PCI device struct of your device, and
+device_mask is a bit mask describing which bits of a PCI address your
+device supports. It returns zero if your card can perform DMA
+properly on the machine given the address mask you provided.
+
+If it returns non-zero, your device cannot perform DMA properly on
+this platform, and attempting to do so will result in undefined
+behavior. You must either use a different mask, or not use DMA.
+
+This means that in the failure case, you have three options:
+
+1) Use another DMA mask, if possible (see below).
+2) Use some non-DMA mode for data transfer, if possible.
+3) Ignore this device and do not initialize it.
+
+It is recommended that your driver print a kernel KERN_WARNING message
+when you end up performing either #2 or #3. In this manner, if a user
+of your driver reports that performance is bad or that the device is not
+even detected, you can ask them for the kernel messages to find out
+exactly why.
+
+The standard 32-bit addressing PCI device would do something like
+this:
+
+ if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
+ printk(KERN_WARNING
+ "mydev: No suitable DMA available.\n");
+ goto ignore_this_device;
+ }
+
+Another common scenario is a 64-bit capable device. The approach
+here is to try for 64-bit DAC addressing, but back down to a
+32-bit mask should that fail. The PCI platform code may fail the
+64-bit mask not because the platform is not capable of 64-bit
+addressing. Rather, it may fail in this case simply because
+32-bit SAC addressing is done more efficiently than DAC addressing.
+Sparc64 is one platform which behaves in this way.
+
+Here is how you would handle a 64-bit capable device which can drive
+all 64-bits when accessing streaming DMA:
+
+ int using_dac;
+
+ if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
+ using_dac = 1;
+ } else if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
+ using_dac = 0;
+ } else {
+ printk(KERN_WARNING
+ "mydev: No suitable DMA available.\n");
+ goto ignore_this_device;
+ }
+
+If a card is capable of using 64-bit consistent allocations as well,
+the case would look like this:
+
+ int using_dac, consistent_using_dac;
+
+ if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
+ using_dac = 1;
+ consistent_using_dac = 1;
+ pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+ } else if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
+ using_dac = 0;
+ consistent_using_dac = 0;
+ pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+ } else {
+ printk(KERN_WARNING
+ "mydev: No suitable DMA available.\n");
+ goto ignore_this_device;
+ }
+
+pci_set_consistent_dma_mask() will always be able to set the same or a
+smaller mask as pci_set_dma_mask(). However for the rare case that a
+device driver only uses consistent allocations, one would have to
+check the return value from pci_set_consistent_dma_mask().
+
+Finally, if your device can only drive the low 24-bits of
+address during PCI bus mastering you might do something like:
+
+ if (pci_set_dma_mask(pdev, DMA_BIT_MASK(24))) {
+ printk(KERN_WARNING
+ "mydev: 24-bit DMA addressing not available.\n");
+ goto ignore_this_device;
+ }
+
+When pci_set_dma_mask() is successful, and returns zero, the PCI layer
+saves away this mask you have provided. The PCI layer will use this
+information later when you make DMA mappings.
+
+There is a case which we are aware of at this time, which is worth
+mentioning in this documentation. If your device supports multiple
+functions (for example a sound card provides playback and record
+functions) and the various different functions have _different_
+DMA addressing limitations, you may wish to probe each mask and
+only provide the functionality which the machine can handle. It
+is important that the last call to pci_set_dma_mask() be for the
+most specific mask.
+
+Here is pseudo-code showing how this might be done:
+
+ #define PLAYBACK_ADDRESS_BITS DMA_BIT_MASK(32)
+ #define RECORD_ADDRESS_BITS DMA_BIT_MASK(24)
+
+ struct my_sound_card *card;
+ struct pci_dev *pdev;
+
+ ...
+ if (!pci_set_dma_mask(pdev, PLAYBACK_ADDRESS_BITS)) {
+ card->playback_enabled = 1;
+ } else {
+ card->playback_enabled = 0;
+ printk(KERN_WARNING "%s: Playback disabled due to DMA limitations.\n",
+ card->name);
+ }
+ if (!pci_set_dma_mask(pdev, RECORD_ADDRESS_BITS)) {
+ card->record_enabled = 1;
+ } else {
+ card->record_enabled = 0;
+ printk(KERN_WARNING "%s: Record disabled due to DMA limitations.\n",
+ card->name);
+ }
+
+A sound card was used as an example here because this genre of PCI
+devices seems to be littered with ISA chips given a PCI front end,
+and thus retaining the 16MB DMA addressing limitations of ISA.
+
+ Types of DMA mappings
+
+There are two types of DMA mappings:
+
+- Consistent DMA mappings which are usually mapped at driver
+ initialization, unmapped at the end and for which the hardware should
+ guarantee that the device and the CPU can access the data
+ in parallel and will see updates made by each other without any
+ explicit software flushing.
+
+ Think of "consistent" as "synchronous" or "coherent".
+
+ The current default is to return consistent memory in the low 32
+ bits of the PCI bus space. However, for future compatibility you
+ should set the consistent mask even if this default is fine for your
+ driver.
+
+ Good examples of what to use consistent mappings for are:
+
+ - Network card DMA ring descriptors.
+ - SCSI adapter mailbox command data structures.
+ - Device firmware microcode executed out of
+ main memory.
+
+ The invariant these examples all require is that any CPU store
+ to memory is immediately visible to the device, and vice
+ versa. Consistent mappings guarantee this.
+
+ IMPORTANT: Consistent DMA memory does not preclude the usage of
+ proper memory barriers. The CPU may reorder stores to
+ consistent memory just as it may normal memory. Example:
+ if it is important for the device to see the first word
+ of a descriptor updated before the second, you must do
+ something like:
+
+ desc->word0 = address;
+ wmb();
+ desc->word1 = DESC_VALID;
+
+ in order to get correct behavior on all platforms.
+
+ Also, on some platforms your driver may need to flush CPU write
+ buffers in much the same way as it needs to flush write buffers
+ found in PCI bridges (such as by reading a register's value
+ after writing it).
+
+- Streaming DMA mappings which are usually mapped for one DMA transfer,
+ unmapped right after it (unless you use pci_dma_sync_* below) and for which
+ hardware can optimize for sequential accesses.
+
+ This of "streaming" as "asynchronous" or "outside the coherency
+ domain".
+
+ Good examples of what to use streaming mappings for are:
+
+ - Networking buffers transmitted/received by a device.
+ - Filesystem buffers written/read by a SCSI device.
+
+ The interfaces for using this type of mapping were designed in
+ such a way that an implementation can make whatever performance
+ optimizations the hardware allows. To this end, when using
+ such mappings you must be explicit about what you want to happen.
+
+Neither type of DMA mapping has alignment restrictions that come
+from PCI, although some devices may have such restrictions.
+Also, systems with caches that aren't DMA-coherent will work better
+when the underlying buffers don't share cache lines with other data.
+
+
+ Using Consistent DMA mappings.
+
+To allocate and map large (PAGE_SIZE or so) consistent DMA regions,
+you should do:
+
+ dma_addr_t dma_handle;
+
+ cpu_addr = pci_alloc_consistent(pdev, size, &dma_handle);
+
+where pdev is a struct pci_dev *. This may be called in interrupt context.
+You should use dma_alloc_coherent (see DMA-API.txt) for buses
+where devices don't have struct pci_dev (like ISA, EISA).
+
+This argument is needed because the DMA translations may be bus
+specific (and often is private to the bus which the device is attached
+to).
+
+Size is the length of the region you want to allocate, in bytes.
+
+This routine will allocate RAM for that region, so it acts similarly to
+__get_free_pages (but takes size instead of a page order). If your
+driver needs regions sized smaller than a page, you may prefer using
+the pci_pool interface, described below.
+
+The consistent DMA mapping interfaces, for non-NULL pdev, will by
+default return a DMA address which is SAC (Single Address Cycle)
+addressable. Even if the device indicates (via PCI dma mask) that it
+may address the upper 32-bits and thus perform DAC cycles, consistent
+allocation will only return > 32-bit PCI addresses for DMA if the
+consistent dma mask has been explicitly changed via
+pci_set_consistent_dma_mask(). This is true of the pci_pool interface
+as well.
+
+pci_alloc_consistent returns two values: the virtual address which you
+can use to access it from the CPU and dma_handle which you pass to the
+card.
+
+The cpu return address and the DMA bus master address are both
+guaranteed to be aligned to the smallest PAGE_SIZE order which
+is greater than or equal to the requested size. This invariant
+exists (for example) to guarantee that if you allocate a chunk
+which is smaller than or equal to 64 kilobytes, the extent of the
+buffer you receive will not cross a 64K boundary.
+
+To unmap and free such a DMA region, you call:
+
+ pci_free_consistent(pdev, size, cpu_addr, dma_handle);
+
+where pdev, size are the same as in the above call and cpu_addr and
+dma_handle are the values pci_alloc_consistent returned to you.
+This function may not be called in interrupt context.
+
+If your driver needs lots of smaller memory regions, you can write
+custom code to subdivide pages returned by pci_alloc_consistent,
+or you can use the pci_pool API to do that. A pci_pool is like
+a kmem_cache, but it uses pci_alloc_consistent not __get_free_pages.
+Also, it understands common hardware constraints for alignment,
+like queue heads needing to be aligned on N byte boundaries.
+
+Create a pci_pool like this:
+
+ struct pci_pool *pool;
+
+ pool = pci_pool_create(name, pdev, size, align, alloc);
+
+The "name" is for diagnostics (like a kmem_cache name); pdev and size
+are as above. The device's hardware alignment requirement for this
+type of data is "align" (which is expressed in bytes, and must be a
+power of two). If your device has no boundary crossing restrictions,
+pass 0 for alloc; passing 4096 says memory allocated from this pool
+must not cross 4KByte boundaries (but at that time it may be better to
+go for pci_alloc_consistent directly instead).
+
+Allocate memory from a pci pool like this:
+
+ cpu_addr = pci_pool_alloc(pool, flags, &dma_handle);
+
+flags are SLAB_KERNEL if blocking is permitted (not in_interrupt nor
+holding SMP locks), SLAB_ATOMIC otherwise. Like pci_alloc_consistent,
+this returns two values, cpu_addr and dma_handle.
+
+Free memory that was allocated from a pci_pool like this:
+
+ pci_pool_free(pool, cpu_addr, dma_handle);
+
+where pool is what you passed to pci_pool_alloc, and cpu_addr and
+dma_handle are the values pci_pool_alloc returned. This function
+may be called in interrupt context.
+
+Destroy a pci_pool by calling:
+
+ pci_pool_destroy(pool);
+
+Make sure you've called pci_pool_free for all memory allocated
+from a pool before you destroy the pool. This function may not
+be called in interrupt context.
+
+ DMA Direction
+
+The interfaces described in subsequent portions of this document
+take a DMA direction argument, which is an integer and takes on
+one of the following values:
+
+ PCI_DMA_BIDIRECTIONAL
+ PCI_DMA_TODEVICE
+ PCI_DMA_FROMDEVICE
+ PCI_DMA_NONE
+
+One should provide the exact DMA direction if you know it.
+
+PCI_DMA_TODEVICE means "from main memory to the PCI device"
+PCI_DMA_FROMDEVICE means "from the PCI device to main memory"
+It is the direction in which the data moves during the DMA
+transfer.
+
+You are _strongly_ encouraged to specify this as precisely
+as you possibly can.
+
+If you absolutely cannot know the direction of the DMA transfer,
+specify PCI_DMA_BIDIRECTIONAL. It means that the DMA can go in
+either direction. The platform guarantees that you may legally
+specify this, and that it will work, but this may be at the
+cost of performance for example.
+
+The value PCI_DMA_NONE is to be used for debugging. One can
+hold this in a data structure before you come to know the
+precise direction, and this will help catch cases where your
+direction tracking logic has failed to set things up properly.
+
+Another advantage of specifying this value precisely (outside of
+potential platform-specific optimizations of such) is for debugging.
+Some platforms actually have a write permission boolean which DMA
+mappings can be marked with, much like page protections in the user
+program address space. Such platforms can and do report errors in the
+kernel logs when the PCI controller hardware detects violation of the
+permission setting.
+
+Only streaming mappings specify a direction, consistent mappings
+implicitly have a direction attribute setting of
+PCI_DMA_BIDIRECTIONAL.
+
+The SCSI subsystem tells you the direction to use in the
+'sc_data_direction' member of the SCSI command your driver is
+working on.
+
+For Networking drivers, it's a rather simple affair. For transmit
+packets, map/unmap them with the PCI_DMA_TODEVICE direction
+specifier. For receive packets, just the opposite, map/unmap them
+with the PCI_DMA_FROMDEVICE direction specifier.
+
+ Using Streaming DMA mappings
+
+The streaming DMA mapping routines can be called from interrupt
+context. There are two versions of each map/unmap, one which will
+map/unmap a single memory region, and one which will map/unmap a
+scatterlist.
+
+To map a single region, you do:
+
+ struct pci_dev *pdev = mydev->pdev;
+ dma_addr_t dma_handle;
+ void *addr = buffer->ptr;
+ size_t size = buffer->len;
+
+ dma_handle = pci_map_single(pdev, addr, size, direction);
+
+and to unmap it:
+
+ pci_unmap_single(pdev, dma_handle, size, direction);
+
+You should call pci_unmap_single when the DMA activity is finished, e.g.
+from the interrupt which told you that the DMA transfer is done.
+
+Using cpu pointers like this for single mappings has a disadvantage,
+you cannot reference HIGHMEM memory in this way. Thus, there is a
+map/unmap interface pair akin to pci_{map,unmap}_single. These
+interfaces deal with page/offset pairs instead of cpu pointers.
+Specifically:
+
+ struct pci_dev *pdev = mydev->pdev;
+ dma_addr_t dma_handle;
+ struct page *page = buffer->page;
+ unsigned long offset = buffer->offset;
+ size_t size = buffer->len;
+
+ dma_handle = pci_map_page(pdev, page, offset, size, direction);
+
+ ...
+
+ pci_unmap_page(pdev, dma_handle, size, direction);
+
+Here, "offset" means byte offset within the given page.
+
+With scatterlists, you map a region gathered from several regions by:
+
+ int i, count = pci_map_sg(pdev, sglist, nents, direction);
+ struct scatterlist *sg;
+
+ for_each_sg(sglist, sg, count, i) {
+ hw_address[i] = sg_dma_address(sg);
+ hw_len[i] = sg_dma_len(sg);
+ }
+
+where nents is the number of entries in the sglist.
+
+The implementation is free to merge several consecutive sglist entries
+into one (e.g. if DMA mapping is done with PAGE_SIZE granularity, any
+consecutive sglist entries can be merged into one provided the first one
+ends and the second one starts on a page boundary - in fact this is a huge
+advantage for cards which either cannot do scatter-gather or have very
+limited number of scatter-gather entries) and returns the actual number
+of sg entries it mapped them to. On failure 0 is returned.
+
+Then you should loop count times (note: this can be less than nents times)
+and use sg_dma_address() and sg_dma_len() macros where you previously
+accessed sg->address and sg->length as shown above.
+
+To unmap a scatterlist, just call:
+
+ pci_unmap_sg(pdev, sglist, nents, direction);
+
+Again, make sure DMA activity has already finished.
+
+PLEASE NOTE: The 'nents' argument to the pci_unmap_sg call must be
+ the _same_ one you passed into the pci_map_sg call,
+ it should _NOT_ be the 'count' value _returned_ from the
+ pci_map_sg call.
+
+Every pci_map_{single,sg} call should have its pci_unmap_{single,sg}
+counterpart, because the bus address space is a shared resource (although
+in some ports the mapping is per each BUS so less devices contend for the
+same bus address space) and you could render the machine unusable by eating
+all bus addresses.
+
+If you need to use the same streaming DMA region multiple times and touch
+the data in between the DMA transfers, the buffer needs to be synced
+properly in order for the cpu and device to see the most uptodate and
+correct copy of the DMA buffer.
+
+So, firstly, just map it with pci_map_{single,sg}, and after each DMA
+transfer call either:
+
+ pci_dma_sync_single_for_cpu(pdev, dma_handle, size, direction);
+
+or:
+
+ pci_dma_sync_sg_for_cpu(pdev, sglist, nents, direction);
+
+as appropriate.
+
+Then, if you wish to let the device get at the DMA area again,
+finish accessing the data with the cpu, and then before actually
+giving the buffer to the hardware call either:
+
+ pci_dma_sync_single_for_device(pdev, dma_handle, size, direction);
+
+or:
+
+ pci_dma_sync_sg_for_device(dev, sglist, nents, direction);
+
+as appropriate.
+
+After the last DMA transfer call one of the DMA unmap routines
+pci_unmap_{single,sg}. If you don't touch the data from the first pci_map_*
+call till pci_unmap_*, then you don't have to call the pci_dma_sync_*
+routines at all.
+
+Here is pseudo code which shows a situation in which you would need
+to use the pci_dma_sync_*() interfaces.
+
+ my_card_setup_receive_buffer(struct my_card *cp, char *buffer, int len)
+ {
+ dma_addr_t mapping;
+
+ mapping = pci_map_single(cp->pdev, buffer, len, PCI_DMA_FROMDEVICE);
+
+ cp->rx_buf = buffer;
+ cp->rx_len = len;
+ cp->rx_dma = mapping;
+
+ give_rx_buf_to_card(cp);
+ }
+
+ ...
+
+ my_card_interrupt_handler(int irq, void *devid, struct pt_regs *regs)
+ {
+ struct my_card *cp = devid;
+
+ ...
+ if (read_card_status(cp) == RX_BUF_TRANSFERRED) {
+ struct my_card_header *hp;
+
+ /* Examine the header to see if we wish
+ * to accept the data. But synchronize
+ * the DMA transfer with the CPU first
+ * so that we see updated contents.
+ */
+ pci_dma_sync_single_for_cpu(cp->pdev, cp->rx_dma,
+ cp->rx_len,
+ PCI_DMA_FROMDEVICE);
+
+ /* Now it is safe to examine the buffer. */
+ hp = (struct my_card_header *) cp->rx_buf;
+ if (header_is_ok(hp)) {
+ pci_unmap_single(cp->pdev, cp->rx_dma, cp->rx_len,
+ PCI_DMA_FROMDEVICE);
+ pass_to_upper_layers(cp->rx_buf);
+ make_and_setup_new_rx_buf(cp);
+ } else {
+ /* Just sync the buffer and give it back
+ * to the card.
+ */
+ pci_dma_sync_single_for_device(cp->pdev,
+ cp->rx_dma,
+ cp->rx_len,
+ PCI_DMA_FROMDEVICE);
+ give_rx_buf_to_card(cp);
+ }
+ }
+ }
+
+Drivers converted fully to this interface should not use virt_to_bus any
+longer, nor should they use bus_to_virt. Some drivers have to be changed a
+little bit, because there is no longer an equivalent to bus_to_virt in the
+dynamic DMA mapping scheme - you have to always store the DMA addresses
+returned by the pci_alloc_consistent, pci_pool_alloc, and pci_map_single
+calls (pci_map_sg stores them in the scatterlist itself if the platform
+supports dynamic DMA mapping in hardware) in your driver structures and/or
+in the card registers.
+
+All PCI drivers should be using these interfaces with no exceptions.
+It is planned to completely remove virt_to_bus() and bus_to_virt() as
+they are entirely deprecated. Some ports already do not provide these
+as it is impossible to correctly support them.
+
+ Optimizing Unmap State Space Consumption
+
+On many platforms, pci_unmap_{single,page}() is simply a nop.
+Therefore, keeping track of the mapping address and length is a waste
+of space. Instead of filling your drivers up with ifdefs and the like
+to "work around" this (which would defeat the whole purpose of a
+portable API) the following facilities are provided.
+
+Actually, instead of describing the macros one by one, we'll
+transform some example code.
+
+1) Use DECLARE_PCI_UNMAP_{ADDR,LEN} in state saving structures.
+ Example, before:
+
+ struct ring_state {
+ struct sk_buff *skb;
+ dma_addr_t mapping;
+ __u32 len;
+ };
+
+ after:
+
+ struct ring_state {
+ struct sk_buff *skb;
+ DECLARE_PCI_UNMAP_ADDR(mapping)
+ DECLARE_PCI_UNMAP_LEN(len)
+ };
+
+ NOTE: DO NOT put a semicolon at the end of the DECLARE_*()
+ macro.
+
+2) Use pci_unmap_{addr,len}_set to set these values.
+ Example, before:
+
+ ringp->mapping = FOO;
+ ringp->len = BAR;
+
+ after:
+
+ pci_unmap_addr_set(ringp, mapping, FOO);
+ pci_unmap_len_set(ringp, len, BAR);
+
+3) Use pci_unmap_{addr,len} to access these values.
+ Example, before:
+
+ pci_unmap_single(pdev, ringp->mapping, ringp->len,
+ PCI_DMA_FROMDEVICE);
+
+ after:
+
+ pci_unmap_single(pdev,
+ pci_unmap_addr(ringp, mapping),
+ pci_unmap_len(ringp, len),
+ PCI_DMA_FROMDEVICE);
+
+It really should be self-explanatory. We treat the ADDR and LEN
+separately, because it is possible for an implementation to only
+need the address in order to perform the unmap operation.
+
+ Platform Issues
+
+If you are just writing drivers for Linux and do not maintain
+an architecture port for the kernel, you can safely skip down
+to "Closing".
+
+1) Struct scatterlist requirements.
+
+ Struct scatterlist must contain, at a minimum, the following
+ members:
+
+ struct page *page;
+ unsigned int offset;
+ unsigned int length;
+
+ The base address is specified by a "page+offset" pair.
+
+ Previous versions of struct scatterlist contained a "void *address"
+ field that was sometimes used instead of page+offset. As of Linux
+ 2.5., page+offset is always used, and the "address" field has been
+ deleted.
+
+2) More to come...
+
+ Handling Errors
+
+DMA address space is limited on some architectures and an allocation
+failure can be determined by:
+
+- checking if pci_alloc_consistent returns NULL or pci_map_sg returns 0
+
+- checking the returned dma_addr_t of pci_map_single and pci_map_page
+ by using pci_dma_mapping_error():
+
+ dma_addr_t dma_handle;
+
+ dma_handle = pci_map_single(pdev, addr, size, direction);
+ if (pci_dma_mapping_error(pdev, dma_handle)) {
+ /*
+ * reduce current DMA mapping usage,
+ * delay and try again later or
+ * reset driver.
+ */
+ }
+
+ Closing
+
+This document, and the API itself, would not be in it's current
+form without the feedback and suggestions from numerous individuals.
+We would like to specifically mention, in no particular order, the
+following people:
+
+ Russell King <rmk@arm.linux.org.uk>
+ Leo Dagum <dagum@barrel.engr.sgi.com>
+ Ralf Baechle <ralf@oss.sgi.com>
+ Grant Grundler <grundler@cup.hp.com>
+ Jay Estabrook <Jay.Estabrook@compaq.com>
+ Thomas Sailer <sailer@ife.ee.ethz.ch>
+ Andrea Arcangeli <andrea@suse.de>
+ Jens Axboe <jens.axboe@oracle.com>
+ David Mosberger-Tang <davidm@hpl.hp.com>
00-INDEX
- This file
-as-iosched.txt
- - Anticipatory IO scheduler
barrier.txt
- I/O Barriers
biodoc.txt
+++ /dev/null
-Anticipatory IO scheduler
--------------------------
-Nick Piggin <piggin@cyberone.com.au> 13 Sep 2003
-
-Attention! Database servers, especially those using "TCQ" disks should
-investigate performance with the 'deadline' IO scheduler. Any system with high
-disk performance requirements should do so, in fact.
-
-If you see unusual performance characteristics of your disk systems, or you
-see big performance regressions versus the deadline scheduler, please email
-me. Database users don't bother unless you're willing to test a lot of patches
-from me ;) its a known issue.
-
-Also, users with hardware RAID controllers, doing striping, may find
-highly variable performance results with using the as-iosched. The
-as-iosched anticipatory implementation is based on the notion that a disk
-device has only one physical seeking head. A striped RAID controller
-actually has a head for each physical device in the logical RAID device.
-
-However, setting the antic_expire (see tunable parameters below) produces
-very similar behavior to the deadline IO scheduler.
-
-Selecting IO schedulers
------------------------
-Refer to Documentation/block/switching-sched.txt for information on
-selecting an io scheduler on a per-device basis.
-
-Anticipatory IO scheduler Policies
-----------------------------------
-The as-iosched implementation implements several layers of policies
-to determine when an IO request is dispatched to the disk controller.
-Here are the policies outlined, in order of application.
-
-1. one-way Elevator algorithm.
-
-The elevator algorithm is similar to that used in deadline scheduler, with
-the addition that it allows limited backward movement of the elevator
-(i.e. seeks backwards). A seek backwards can occur when choosing between
-two IO requests where one is behind the elevator's current position, and
-the other is in front of the elevator's position. If the seek distance to
-the request in back of the elevator is less than half the seek distance to
-the request in front of the elevator, then the request in back can be chosen.
-Backward seeks are also limited to a maximum of MAXBACK (1024*1024) sectors.
-This favors forward movement of the elevator, while allowing opportunistic
-"short" backward seeks.
-
-2. FIFO expiration times for reads and for writes.
-
-This is again very similar to the deadline IO scheduler. The expiration
-times for requests on these lists is tunable using the parameters read_expire
-and write_expire discussed below. When a read or a write expires in this way,
-the IO scheduler will interrupt its current elevator sweep or read anticipation
-to service the expired request.
-
-3. Read and write request batching
-
-A batch is a collection of read requests or a collection of write
-requests. The as scheduler alternates dispatching read and write batches
-to the driver. In the case a read batch, the scheduler submits read
-requests to the driver as long as there are read requests to submit, and
-the read batch time limit has not been exceeded (read_batch_expire).
-The read batch time limit begins counting down only when there are
-competing write requests pending.
-
-In the case of a write batch, the scheduler submits write requests to
-the driver as long as there are write requests available, and the
-write batch time limit has not been exceeded (write_batch_expire).
-However, the length of write batches will be gradually shortened
-when read batches frequently exceed their time limit.
-
-When changing between batch types, the scheduler waits for all requests
-from the previous batch to complete before scheduling requests for the
-next batch.
-
-The read and write fifo expiration times described in policy 2 above
-are checked only when in scheduling IO of a batch for the corresponding
-(read/write) type. So for example, the read FIFO timeout values are
-tested only during read batches. Likewise, the write FIFO timeout
-values are tested only during write batches. For this reason,
-it is generally not recommended for the read batch time
-to be longer than the write expiration time, nor for the write batch
-time to exceed the read expiration time (see tunable parameters below).
-
-When the IO scheduler changes from a read to a write batch,
-it begins the elevator from the request that is on the head of the
-write expiration FIFO. Likewise, when changing from a write batch to
-a read batch, scheduler begins the elevator from the first entry
-on the read expiration FIFO.
-
-4. Read anticipation.
-
-Read anticipation occurs only when scheduling a read batch.
-This implementation of read anticipation allows only one read request
-to be dispatched to the disk controller at a time. In
-contrast, many write requests may be dispatched to the disk controller
-at a time during a write batch. It is this characteristic that can make
-the anticipatory scheduler perform anomalously with controllers supporting
-TCQ, or with hardware striped RAID devices. Setting the antic_expire
-queue parameter (see below) to zero disables this behavior, and the
-anticipatory scheduler behaves essentially like the deadline scheduler.
-
-When read anticipation is enabled (antic_expire is not zero), reads
-are dispatched to the disk controller one at a time.
-At the end of each read request, the IO scheduler examines its next
-candidate read request from its sorted read list. If that next request
-is from the same process as the request that just completed,
-or if the next request in the queue is "very close" to the
-just completed request, it is dispatched immediately. Otherwise,
-statistics (average think time, average seek distance) on the process
-that submitted the just completed request are examined. If it seems
-likely that that process will submit another request soon, and that
-request is likely to be near the just completed request, then the IO
-scheduler will stop dispatching more read requests for up to (antic_expire)
-milliseconds, hoping that process will submit a new request near the one
-that just completed. If such a request is made, then it is dispatched
-immediately. If the antic_expire wait time expires, then the IO scheduler
-will dispatch the next read request from the sorted read queue.
-
-To decide whether an anticipatory wait is worthwhile, the scheduler
-maintains statistics for each process that can be used to compute
-mean "think time" (the time between read requests), and mean seek
-distance for that process. One observation is that these statistics
-are associated with each process, but those statistics are not associated
-with a specific IO device. So for example, if a process is doing IO
-on several file systems on separate devices, the statistics will be
-a combination of IO behavior from all those devices.
-
-
-Tuning the anticipatory IO scheduler
-------------------------------------
-When using 'as', the anticipatory IO scheduler there are 5 parameters under
-/sys/block/*/queue/iosched/. All are units of milliseconds.
-
-The parameters are:
-* read_expire
- Controls how long until a read request becomes "expired". It also controls the
- interval between which expired requests are served, so set to 50, a request
- might take anywhere < 100ms to be serviced _if_ it is the next on the
- expired list. Obviously request expiration strategies won't make the disk
- go faster. The result basically equates to the timeslice a single reader
- gets in the presence of other IO. 100*((seek time / read_expire) + 1) is
- very roughly the % streaming read efficiency your disk should get with
- multiple readers.
-
-* read_batch_expire
- Controls how much time a batch of reads is given before pending writes are
- served. A higher value is more efficient. This might be set below read_expire
- if writes are to be given higher priority than reads, but reads are to be
- as efficient as possible when there are no writes. Generally though, it
- should be some multiple of read_expire.
-
-* write_expire, and
-* write_batch_expire are equivalent to the above, for writes.
-
-* antic_expire
- Controls the maximum amount of time we can anticipate a good read (one
- with a short seek distance from the most recently completed request) before
- giving up. Many other factors may cause anticipation to be stopped early,
- or some processes will not be "anticipated" at all. Should be a bit higher
- for big seek time devices though not a linear correspondence - most
- processes have only a few ms thinktime.
-
-In addition to the tunables above there is a read-only file named est_time
-which, when read, will show:
-
- - The probability of a task exiting without a cooperating task
- submitting an anticipated IO.
-
- - The current mean think time.
-
- - The seek distance used to determine if an incoming IO is better.
-
do not have a corresponding kernel virtual address space mapping) and
low-memory pages.
-Note: Please refer to Documentation/DMA-mapping.txt for a discussion
+Note: Please refer to Documentation/PCI/PCI-DMA-mapping.txt for a discussion
on PCI high mem DMA aspects and mapping of scatter gather lists, and support
for 64 bit PCI.
also be used to enable or disable barriers, for
consistency with other ext4 mount options.
-inode_readahead=n This tuning parameter controls the maximum
+inode_readahead_blks=n This tuning parameter controls the maximum
number of inode table blocks that ext4's inode
table readahead algorithm will pre-read into
the buffer cache. The default value is 32 blocks.
acpi_sleep= [HW,ACPI] Sleep options
Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
- old_ordering, s4_nonvs }
+ old_ordering, s4_nonvs, sci_force_enable }
See Documentation/power/video.txt for information on
s3_bios and s3_mode.
s3_beep is for debugging; it makes the PC's speaker beep
of _PTS is used by default).
s4_nonvs prevents the kernel from saving/restoring the
ACPI NVS memory during hibernation.
+ sci_force_enable causes the kernel to set SCI_EN directly
+ on resume from S1/S3 (which is against the ACPI spec,
+ but some broken systems don't work without it).
acpi_use_timer_override [HW,ACPI]
Use timer override. For some broken Nvidia NF5 boards
__u8 pad;
} nmi;
__u32 sipi_vector;
- __u32 flags; /* must be zero */
+ __u32 flags;
};
4.30 KVM_SET_VCPU_EVENTS
See KVM_GET_VCPU_EVENTS for the data structure.
+Fields that may be modified asynchronously by running VCPUs can be excluded
+from the update. These fields are nmi.pending and sipi_vector. Keep the
+corresponding bits in the flags field cleared to suppress overwriting the
+current in-kernel state. The bits are:
+
+KVM_VCPUEVENT_VALID_NMI_PENDING - transfer nmi.pending to the kernel
+KVM_VCPUEVENT_VALID_SIPI_VECTOR - transfer sipi_vector
+
5. The kvm_run structure
its level up and down at every change.
-Volume control
---------------
+Volume control (Console Audio control)
+--------------------------------------
procfs: /proc/acpi/ibm/volume
ALSA: "ThinkPad Console Audio Control", default ID: "ThinkPadEC"
Software volume control should be done only in the main AC97/HDA
mixer.
-This feature allows volume control on ThinkPad models with a digital
-volume knob (when available, not all models have it), as well as
-mute/unmute control. The available commands are:
+
+About the ThinkPad Console Audio control:
+
+ThinkPads have a built-in amplifier and muting circuit that drives the
+console headphone and speakers. This circuit is after the main AC97
+or HDA mixer in the audio path, and under exclusive control of the
+firmware.
+
+ThinkPads have three special hotkeys to interact with the console
+audio control: volume up, volume down and mute.
+
+It is worth noting that the normal way the mute function works (on
+ThinkPads that do not have a "mute LED") is:
+
+1. Press mute to mute. It will *always* mute, you can press it as
+ many times as you want, and the sound will remain mute.
+
+2. Press either volume key to unmute the ThinkPad (it will _not_
+ change the volume, it will just unmute).
+
+This is a very superior design when compared to the cheap software-only
+mute-toggle solution found on normal consumer laptops: you can be
+absolutely sure the ThinkPad will not make noise if you press the mute
+button, no matter the previous state.
+
+The IBM ThinkPads, and the earlier Lenovo ThinkPads have variable-gain
+amplifiers driving the speakers and headphone output, and the firmware
+also handles volume control for the headphone and speakers on these
+ThinkPads without any help from the operating system (this volume
+control stage exists after the main AC97 or HDA mixer in the audio
+path).
+
+The newer Lenovo models only have firmware mute control, and depend on
+the main HDA mixer to do volume control (which is done by the operating
+system). In this case, the volume keys are filtered out for unmute
+key press (there are some firmware bugs in this area) and delivered as
+normal key presses to the operating system (thinkpad-acpi is not
+involved).
+
+
+The ThinkPad-ACPI volume control:
+
+The preferred way to interact with the Console Audio control is the
+ALSA interface.
+
+The legacy procfs interface allows one to read the current state,
+and if volume control is enabled, accepts the following commands:
echo up >/proc/acpi/ibm/volume
echo down >/proc/acpi/ibm/volume
echo 'level <level>' >/proc/acpi/ibm/volume
The <level> number range is 0 to 14 although not all of them may be
-distinct. The unmute the volume after the mute command, use either the
+distinct. To unmute the volume after the mute command, use either the
up or down command (the level command will not unmute the volume), or
the unmute command.
-The current volume level and mute state is shown in the file.
-
You can use the volume_capabilities parameter to tell the driver
whether your thinkpad has volume control or mute-only control:
volume_capabilities=1 for mixers with mute and volume control,
It takes an integer value, can be changed by writing to this
file, such as
- # cat 5 > /proc/asound/card0/pcm0p/xrun_debug
+ # echo 5 > /proc/asound/card0/pcm0p/xrun_debug
The value consists of the following bit flags:
bit 0 = Enable XRUN/jiffies debug messages
For example, if the function foo() calls bar(), when the bar() function calls
mcount(), the arguments mcount() will pass to the tracer are:
"frompc" - the address bar() will use to return to foo()
- "selfpc" - the address bar() (with _mcount() size adjustment)
+ "selfpc" - the address bar() (with mcount() size adjustment)
Also keep in mind that this mcount function will be called *a lot*, so
optimizing for the default case of no tracer will help the smooth running of
your system when tracing is disabled. So the start of the mcount function is
-typically the bare min with checking things before returning. That also means
-the code flow should usually kept linear (i.e. no branching in the nop case).
-This is of course an optimization and not a hard requirement.
+typically the bare minimum with checking things before returning. That also
+means the code flow should usually be kept linear (i.e. no branching in the nop
+case). This is of course an optimization and not a hard requirement.
Here is some pseudo code that should help (these functions should actually be
implemented in assembly):
The mcount function should check the function pointers ftrace_graph_return
(compare to ftrace_stub) and ftrace_graph_entry (compare to
-ftrace_graph_entry_stub). If either of those are not set to the relevant stub
+ftrace_graph_entry_stub). If either of those is not set to the relevant stub
function, call the arch-specific function ftrace_graph_caller which in turn
calls the arch-specific function prepare_ftrace_return. Neither of these
-function names are strictly required, but you should use them anyways to stay
+function names is strictly required, but you should use them anyway to stay
consistent across the architecture ports -- easier to compare & contrast
things.
located on the stack. This allows the function to hijack the return address
temporarily to have it point to the arch-specific function return_to_handler.
That function will simply call the common ftrace_return_to_handler function and
-that will return the original return address with which, you can return to the
+that will return the original return address with which you can return to the
original call site.
Here is the updated mcount pseudo code:
Usage
-----
-Make sure debugfs is mounted to /sys/kernel/debug. If not, (requires root privileges)
+Make sure debugfs is mounted to /sys/kernel/debug.
+If not (requires root privileges):
$ mount -t debugfs debugfs /sys/kernel/debug
Check that the driver you are about to trace is not loaded.
$ tar zcf pciid-nick-mmiotrace.tar.gz mydump.txt lspci.txt dmesg.txt
and then send the .tar.gz file. The trace compresses considerably. Replace
"pciid" and "nick" with the PCI ID or model name of your piece of hardware
-under investigation and your nick name.
+under investigation and your nickname.
How Mmiotrace Works
Access to hardware IO-memory is gained by mapping addresses from PCI bus by
calling one of the ioremap_*() functions. Mmiotrace is hooked into the
__ioremap() function and gets called whenever a mapping is created. Mapping is
-an event that is recorded into the trace log. Note, that ISA range mappings
+an event that is recorded into the trace log. Note that ISA range mappings
are not caught, since the mapping always exists and is returned directly.
MMIO accesses are recorded via page faults. Just before __ioremap() returns,
----------------
The raw log is text and easily filtered with e.g. grep and awk. One record is
-one line in the log. A record starts with a keyword, followed by keyword
-dependant arguments. Arguments are separated by a space, or continue until the
+one line in the log. A record starts with a keyword, followed by keyword-
+dependent arguments. Arguments are separated by a space, or continue until the
end of line. The format for version 20070824 is as follows:
-Explanation Keyword Space separated arguments
+Explanation Keyword Space-separated arguments
---------------------------------------------------------------------------
read event R width, timestamp, map id, physical, value, PC, PID
marker MARK timestamp, text
version VERSION the string "20070824"
info for reader LSPCI one line from lspci -v
-PCI address map PCIDEV space separated /proc/bus/pci/devices data
+PCI address map PCIDEV space-separated /proc/bus/pci/devices data
unk. opcode UNKNOWN timestamp, map id, physical, data, PC, PID
Timestamp is in seconds with decimals. Physical is a PCI bus address, virtual
creating custom kernel modules to register probe functions using the event
tracing infrastructure.
-Simplistically, tracepoints will represent an important event that when can
-be taken in conjunction with other tracepoints to build a "Big Picture" of
+Simplistically, tracepoints represent important events that can be
+taken in conjunction with other tracepoints to build a "Big Picture" of
what is going on within the system. There are a large number of methods for
gathering and interpreting these events. Lacking any current Best Practises,
this document describes some of the methods that can be used.
will give a fair indication of the number of events available.
-2.2 PCL
+2.2 PCL (Performance Counters for Linux)
-------
-Discovery and enumeration of all counters and events, including tracepoints
+Discovery and enumeration of all counters and events, including tracepoints,
are available with the perf tool. Getting a list of available events is a
-simple case of
+simple case of:
$ perf list 2>&1 | grep Tracepoint
ext4:ext4_free_inode [Tracepoint event]
[ .... remaining output snipped .... ]
-2. Enabling Events
+3. Enabling Events
==================
-2.1 System-Wide Event Enabling
+3.1 System-Wide Event Enabling
------------------------------
See Documentation/trace/events.txt for a proper description on how events
can be enabled system-wide. A short example of enabling all events related
-to page allocation would look something like
+to page allocation would look something like:
$ for i in `find /sys/kernel/debug/tracing/events -name "enable" | grep mm_`; do echo 1 > $i; done
-2.2 System-Wide Event Enabling with SystemTap
+3.2 System-Wide Event Enabling with SystemTap
---------------------------------------------
In SystemTap, tracepoints are accessible using the kernel.trace() function
print_count()
}
-2.3 System-Wide Event Enabling with PCL
+3.3 System-Wide Event Enabling with PCL
---------------------------------------
By specifying the -a switch and analysing sleep, the system-wide events
Similarly, one could execute a shell and exit it as desired to get a report
at that point.
-2.4 Local Event Enabling
+3.4 Local Event Enabling
------------------------
Documentation/trace/ftrace.txt describes how to enable events on a per-thread
basis using set_ftrace_pid.
-2.5 Local Event Enablement with PCL
+3.5 Local Event Enablement with PCL
-----------------------------------
-Events can be activate and tracked for the duration of a process on a local
+Events can be activated and tracked for the duration of a process on a local
basis using PCL such as follows.
$ perf stat -e kmem:mm_page_alloc -e kmem:mm_page_free_direct \
0.973913387 seconds time elapsed
-3. Event Filtering
+4. Event Filtering
==================
Documentation/trace/ftrace.txt covers in-depth how to filter events in
ftrace. Obviously using grep and awk of trace_pipe is an option as well
as any script reading trace_pipe.
-4. Analysing Event Variances with PCL
+5. Analysing Event Variances with PCL
=====================================
Any workload can exhibit variances between runs and it can be important
-to know what the standard deviation in. By and large, this is left to the
+to know what the standard deviation is. By and large, this is left to the
performance analyst to do it by hand. In the event that the discrete event
occurrences are useful to the performance analyst, then perf can be used.
aggregation of discrete events, then a script would need to be developed.
Using --repeat, it is also possible to view how events are fluctuating over
-time on a system wide basis using -a and sleep.
+time on a system-wide basis using -a and sleep.
$ perf stat -e kmem:mm_page_alloc -e kmem:mm_page_free_direct \
-e kmem:mm_pagevec_free \
1.002251757 seconds time elapsed ( +- 0.005% )
-5. Higher-Level Analysis with Helper Scripts
+6. Higher-Level Analysis with Helper Scripts
============================================
When events are enabled the events that are triggering can be read from
o Reading information from /proc for the PID that triggered the event
o Deriving a higher-level event from a series of lower-level events.
- o Calculate latencies between two events
+ o Calculating latencies between two events
Documentation/trace/postprocess/trace-pagealloc-postprocess.pl is an example
script that can read trace_pipe from STDIN or a copy of a trace. When used
-on-line, it can be interrupted once to generate a report without existing
+on-line, it can be interrupted once to generate a report without exiting
and twice to exit.
Simplistically, the script just reads STDIN and counts up events but it
processes, the parent process responsible for creating all the helpers
can be identified
-6. Lower-Level Analysis with PCL
+7. Lower-Level Analysis with PCL
================================
-There may also be a requirement to identify what functions with a program
+There may also be a requirement to identify what functions within a program
were generating events within the kernel. To begin this sort of analysis, the
-data must be recorded. At the time of writing, this required root
+data must be recorded. At the time of writing, this required root:
$ perf record -c 1 \
-e kmem:mm_page_alloc -e kmem:mm_page_free_direct \
# (For more details, try: perf report --sort comm,dso,symbol)
#
-According to this, the vast majority of events occured triggered on events
-within the VDSO. With simple binaries, this will often be the case so lets
+According to this, the vast majority of events triggered on events
+within the VDSO. With simple binaries, this will often be the case so let's
take a slightly different example. In the course of writing this, it was
-noticed that X was generating an insane amount of page allocations so lets look
-at it
+noticed that X was generating an insane amount of page allocations so let's look
+at it:
$ perf record -c 1 -f \
-e kmem:mm_page_alloc -e kmem:mm_page_free_direct \
# (For more details, try: perf report --sort comm,dso,symbol)
#
-So, almost half of the events are occuring in a library. To get an idea which
-symbol.
+So, almost half of the events are occurring in a library. To get an idea which
+symbol:
$ perf report --sort comm,dso,symbol
# Samples: 27666
0.01% Xorg /opt/gfx-test/lib/libpixman-1.so.0.13.1 [.] get_fast_path
0.00% Xorg [kernel] [k] ftrace_trace_userstack
-To see where within the function pixmanFillsse2 things are going wrong
+To see where within the function pixmanFillsse2 things are going wrong:
$ perf annotate pixmanFillsse2
[ ... ]
----------------
To use the vga arbiter char device it was implemented an API inside the
-libpciaccess library. One fieldd was added to struct pci_device (each device
+libpciaccess library. One field was added to struct pci_device (each device
on the system):
/* the type of resource decoded by the device */
F: include/linux/f75375s.h
FIREWIRE SUBSYSTEM
-M: Kristian Hoegsberg <krh@redhat.com>
M: Stefan Richter <stefanr@s5r6.in-berlin.de>
L: linux1394-devel@lists.sourceforge.net
-W: http://www.linux1394.org/
+W: http://ieee1394.wiki.kernel.org/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6.git
S: Maintained
F: drivers/firewire/
F: drivers/idle/i7300_idle.c
IEEE 1394 SUBSYSTEM
-M: Ben Collins <ben.collins@ubuntu.com>
M: Stefan Richter <stefanr@s5r6.in-berlin.de>
L: linux1394-devel@lists.sourceforge.net
-W: http://www.linux1394.org/
+W: http://ieee1394.wiki.kernel.org/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6.git
-S: Maintained
+S: Obsolete
F: Documentation/debugging-via-ohci1394.txt
F: drivers/ieee1394/
-IEEE 1394 RAW I/O DRIVER
-M: Dan Dennedy <dan@dennedy.org>
-M: Stefan Richter <stefanr@s5r6.in-berlin.de>
-L: linux1394-devel@lists.sourceforge.net
-S: Maintained
-F: drivers/ieee1394/raw1394*
-
IEEE 802.15.4 SUBSYSTEM
M: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
M: Sergey Lapin <slapin@ossfans.org>
#define _vmm_raw_spin_lock(x) do {}while(0)
#define _vmm_raw_spin_unlock(x) do {}while(0)
#else
+typedef struct {
+ volatile unsigned int lock;
+} vmm_spinlock_t;
#define _vmm_raw_spin_lock(x) \
do { \
__u32 *ia64_spinlock_ptr = (__u32 *) (x); \
#define _vmm_raw_spin_unlock(x) \
do { barrier(); \
- ((spinlock_t *)x)->raw_lock.lock = 0; } \
+ ((vmm_spinlock_t *)x)->lock = 0; } \
while (0)
#endif
-void vmm_spin_lock(spinlock_t *lock);
-void vmm_spin_unlock(spinlock_t *lock);
+void vmm_spin_lock(vmm_spinlock_t *lock);
+void vmm_spin_unlock(vmm_spinlock_t *lock);
enum {
I_TLB = 1,
D_TLB = 2
return ;
}
-void vmm_spin_lock(spinlock_t *lock)
+void vmm_spin_lock(vmm_spinlock_t *lock)
{
_vmm_raw_spin_lock(lock);
}
-void vmm_spin_unlock(spinlock_t *lock)
+void vmm_spin_unlock(vmm_spinlock_t *lock)
{
_vmm_raw_spin_unlock(lock);
}
{
u64 i, dirty_pages = 1;
u64 base_gfn = (pte&_PAGE_PPN_MASK) >> PAGE_SHIFT;
- spinlock_t *lock = __kvm_va(v->arch.dirty_log_lock_pa);
+ vmm_spinlock_t *lock = __kvm_va(v->arch.dirty_log_lock_pa);
void *dirty_bitmap = (void *)KVM_MEM_DIRTY_LOG_BASE;
dirty_pages <<= ps <= PAGE_SHIFT ? 0 : ps - PAGE_SHIFT;
list_for_each_entry(dev, &bus->devices, bus_list) {
struct dev_archdata *sd = &dev->dev.archdata;
+ /* Cardbus can call us to add new devices to a bus, so ignore
+ * those who are already fully discovered
+ */
+ if (dev->is_added)
+ continue;
+
/* Setup OF node pointer in archdata */
sd->of_node = pci_device_to_OF_node(dev);
}
EXPORT_SYMBOL(pcibios_fixup_bus);
+void __devinit pci_fixup_cardbus(struct pci_bus *bus)
+{
+ /* Now fixup devices on that bus */
+ pcibios_setup_bus_devices(bus);
+}
+
+
static int skip_isa_ioresource_align(struct pci_dev *dev)
{
if ((ppc_pci_flags & PPC_PCI_CAN_SKIP_ISA_ALIGN) &&
{
u64 rb = 0, rs = 0;
+ /*
+ * According to Book3 2.01 mtsrin is implemented as:
+ *
+ * The SLB entry specified by (RB)32:35 is loaded from register
+ * RS, as follows.
+ *
+ * SLBE Bit Source SLB Field
+ *
+ * 0:31 0x0000_0000 ESID-0:31
+ * 32:35 (RB)32:35 ESID-32:35
+ * 36 0b1 V
+ * 37:61 0x00_0000|| 0b0 VSID-0:24
+ * 62:88 (RS)37:63 VSID-25:51
+ * 89:91 (RS)33:35 Ks Kp N
+ * 92 (RS)36 L ((RS)36 must be 0b0)
+ * 93 0b0 C
+ */
+
+ dprintk("KVM MMU: mtsrin(0x%x, 0x%lx)\n", srnum, value);
+
/* ESID = srnum */
rb |= (srnum & 0xf) << 28;
/* Set the valid bit */
/* VSID = VSID */
rs |= (value & 0xfffffff) << 12;
/* flags = flags */
- rs |= ((value >> 27) & 0xf) << 9;
+ rs |= ((value >> 28) & 0x7) << 9;
kvmppc_mmu_book3s_64_slbmte(vcpu, rs, rb);
}
KBUILD_CFLAGS := -m$(BITS) -D__KERNEL__ $(LINUX_INCLUDE) -O2
KBUILD_CFLAGS += -fno-strict-aliasing -fPIC
KBUILD_CFLAGS += -DDISABLE_BRANCH_PROFILING
+cflags-$(CONFIG_X86_32) := -march=i386
cflags-$(CONFIG_X86_64) := -mcmodel=small
KBUILD_CFLAGS += $(cflags-y)
KBUILD_CFLAGS += $(call cc-option,-ffreestanding)
__u8 reserved[31];
};
+/* When set in flags, include corresponding fields on KVM_SET_VCPU_EVENTS */
+#define KVM_VCPUEVENT_VALID_NMI_PENDING 0x00000001
+#define KVM_VCPUEVENT_VALID_SIPI_VECTOR 0x00000002
+
/* for KVM_GET/SET_VCPU_EVENTS */
struct kvm_vcpu_events {
struct {
* contiguous (although various IO spaces may punch holes in
* it)..
*
- * N - Number of bits in the node portion of a socket physical
- * address.
+ * N - Number of bits in the node portion of a socket physical
+ * address.
*
- * NASID - network ID of a router, Mbrick or Cbrick. Nasid values of
- * routers always have low bit of 1, C/MBricks have low bit
- * equal to 0. Most addressing macros that target UV hub chips
- * right shift the NASID by 1 to exclude the always-zero bit.
- * NASIDs contain up to 15 bits.
+ * NASID - network ID of a router, Mbrick or Cbrick. Nasid values of
+ * routers always have low bit of 1, C/MBricks have low bit
+ * equal to 0. Most addressing macros that target UV hub chips
+ * right shift the NASID by 1 to exclude the always-zero bit.
+ * NASIDs contain up to 15 bits.
*
* GNODE - NASID right shifted by 1 bit. Most mmrs contain gnodes instead
* of nasids.
*
- * PNODE - the low N bits of the GNODE. The PNODE is the most useful variant
- * of the nasid for socket usage.
+ * PNODE - the low N bits of the GNODE. The PNODE is the most useful variant
+ * of the nasid for socket usage.
*
*
* NumaLink Global Physical Address Format:
*
*
* APICID format
- * NOTE!!!!!! This is the current format of the APICID. However, code
- * should assume that this will change in the future. Use functions
- * in this file for all APICID bit manipulations and conversion.
+ * NOTE!!!!!! This is the current format of the APICID. However, code
+ * should assume that this will change in the future. Use functions
+ * in this file for all APICID bit manipulations and conversion.
*
- * 1111110000000000
- * 5432109876543210
+ * 1111110000000000
+ * 5432109876543210
* pppppppppplc0cch
* sssssssssss
*
* Note: Processor only supports 12 bits in the APICID register. The ACPI
* tables hold all 16 bits. Software needs to be aware of this.
*
- * Unless otherwise specified, all references to APICID refer to
- * the FULL value contained in ACPI tables, not the subset in the
- * processor APICID register.
+ * Unless otherwise specified, all references to APICID refer to
+ * the FULL value contained in ACPI tables, not the subset in the
+ * processor APICID register.
*/
};
DECLARE_PER_CPU(struct uv_hub_info_s, __uv_hub_info);
-#define uv_hub_info (&__get_cpu_var(__uv_hub_info))
+#define uv_hub_info (&__get_cpu_var(__uv_hub_info))
#define uv_cpu_hub_info(cpu) (&per_cpu(__uv_hub_info, cpu))
/*
* Local & Global MMR space macros.
- * Note: macros are intended to be used ONLY by inline functions
- * in this file - not by other kernel code.
- * n - NASID (full 15-bit global nasid)
- * g - GNODE (full 15-bit global nasid, right shifted 1)
- * p - PNODE (local part of nsids, right shifted 1)
+ * Note: macros are intended to be used ONLY by inline functions
+ * in this file - not by other kernel code.
+ * n - NASID (full 15-bit global nasid)
+ * g - GNODE (full 15-bit global nasid, right shifted 1)
+ * p - PNODE (local part of nsids, right shifted 1)
*/
#define UV_NASID_TO_PNODE(n) (((n) >> 1) & uv_hub_info->pnode_mask)
#define UV_PNODE_TO_GNODE(p) ((p) |uv_hub_info->gnode_extra)
/*
* Macros for converting between kernel virtual addresses, socket local physical
* addresses, and UV global physical addresses.
- * Note: use the standard __pa() & __va() macros for converting
- * between socket virtual and socket physical addresses.
+ * Note: use the standard __pa() & __va() macros for converting
+ * between socket virtual and socket physical addresses.
*/
/* socket phys RAM --> UV global physical address */
* Access global MMRs using the low memory MMR32 space. This region supports
* faster MMR access but not all MMRs are accessible in this space.
*/
-static inline unsigned long *uv_global_mmr32_address(int pnode,
- unsigned long offset)
+static inline unsigned long *uv_global_mmr32_address(int pnode, unsigned long offset)
{
return __va(UV_GLOBAL_MMR32_BASE |
UV_GLOBAL_MMR32_PNODE_BITS(pnode) | offset);
}
-static inline void uv_write_global_mmr32(int pnode, unsigned long offset,
- unsigned long val)
+static inline void uv_write_global_mmr32(int pnode, unsigned long offset, unsigned long val)
{
writeq(val, uv_global_mmr32_address(pnode, offset));
}
-static inline unsigned long uv_read_global_mmr32(int pnode,
- unsigned long offset)
+static inline unsigned long uv_read_global_mmr32(int pnode, unsigned long offset)
{
return readq(uv_global_mmr32_address(pnode, offset));
}
* Access Global MMR space using the MMR space located at the top of physical
* memory.
*/
-static inline unsigned long *uv_global_mmr64_address(int pnode,
- unsigned long offset)
+static inline unsigned long *uv_global_mmr64_address(int pnode, unsigned long offset)
{
return __va(UV_GLOBAL_MMR64_BASE |
UV_GLOBAL_MMR64_PNODE_BITS(pnode) | offset);
}
-static inline void uv_write_global_mmr64(int pnode, unsigned long offset,
- unsigned long val)
+static inline void uv_write_global_mmr64(int pnode, unsigned long offset, unsigned long val)
{
writeq(val, uv_global_mmr64_address(pnode, offset));
}
-static inline unsigned long uv_read_global_mmr64(int pnode,
- unsigned long offset)
+static inline unsigned long uv_read_global_mmr64(int pnode, unsigned long offset)
{
return readq(uv_global_mmr64_address(pnode, offset));
}
return UV_GLOBAL_GRU_MMR_BASE | offset | (pnode << uv_hub_info->m_val);
}
+static inline void uv_write_global_mmr8(int pnode, unsigned long offset, unsigned char val)
+{
+ writeb(val, uv_global_mmr64_address(pnode, offset));
+}
+
+static inline unsigned char uv_read_global_mmr8(int pnode, unsigned long offset)
+{
+ return readb(uv_global_mmr64_address(pnode, offset));
+}
+
/*
* Access hub local MMRs. Faster than using global space but only local MMRs
* are accessible.
}
}
+static inline unsigned long uv_scir_offset(int apicid)
+{
+ return SCIR_LOCAL_MMR_BASE | (apicid & 0x3f);
+}
+
static inline void uv_set_cpu_scir_bits(int cpu, unsigned char value)
{
if (uv_cpu_hub_info(cpu)->scir.state != value) {
+ uv_write_global_mmr8(uv_cpu_to_pnode(cpu),
+ uv_cpu_hub_info(cpu)->scir.offset, value);
uv_cpu_hub_info(cpu)->scir.state = value;
- uv_write_local_mmr8(uv_cpu_hub_info(cpu)->scir.offset, value);
}
}
#endif
if (strncmp(str, "old_ordering", 12) == 0)
acpi_old_suspend_ordering();
+ if (strncmp(str, "sci_force_enable", 16) == 0)
+ acpi_set_sci_en_on_resume();
str = strchr(str, ',');
if (str != NULL)
str += strspn(str, ", \t");
/* IOMMUs have a non-present cache? */
bool amd_iommu_np_cache __read_mostly;
+/*
+ * Set to true if ACPI table parsing and hardware intialization went properly
+ */
+static bool amd_iommu_initialized;
+
/*
* List of protection domains - used during resume
*/
}
WARN_ON(p != end);
+ amd_iommu_initialized = true;
+
return 0;
}
if (acpi_table_parse("IVRS", init_iommu_all) != 0)
goto free;
+ if (!amd_iommu_initialized)
+ goto free;
+
if (acpi_table_parse("IVRS", init_memory_definitions) != 0)
goto free;
uv_rtc_init();
for_each_present_cpu(cpu) {
+ int apicid = per_cpu(x86_cpu_to_apicid, cpu);
+
nid = cpu_to_node(cpu);
- pnode = uv_apicid_to_pnode(per_cpu(x86_cpu_to_apicid, cpu));
+ pnode = uv_apicid_to_pnode(apicid);
blade = boot_pnode_to_blade(pnode);
lcpu = uv_blade_info[blade].nr_possible_cpus;
uv_blade_info[blade].nr_possible_cpus++;
uv_cpu_hub_info(cpu)->gnode_extra = gnode_extra;
uv_cpu_hub_info(cpu)->global_mmr_base = mmr_base;
uv_cpu_hub_info(cpu)->coherency_domain_number = sn_coherency_id;
- uv_cpu_hub_info(cpu)->scir.offset = SCIR_LOCAL_MMR_BASE + lcpu;
+ uv_cpu_hub_info(cpu)->scir.offset = uv_scir_offset(apicid);
uv_node_to_blade[nid] = blade;
uv_cpu_to_blade[cpu] = blade;
max_pnode = max(pnode, max_pnode);
- printk(KERN_DEBUG "UV: cpu %d, apicid 0x%x, pnode %d, nid %d, "
- "lcpu %d, blade %d\n",
- cpu, per_cpu(x86_cpu_to_apicid, cpu), pnode, nid,
- lcpu, blade);
+ printk(KERN_DEBUG "UV: cpu %d, apicid 0x%x, pnode %d, nid %d, lcpu %d, blade %d\n",
+ cpu, apicid, pnode, nid, lcpu, blade);
}
/* Add blade/pnode info for nodes without cpus */
callchain_store(entry, PERF_CONTEXT_KERNEL);
callchain_store(entry, regs->ip);
- dump_trace(NULL, regs, NULL, 0, &backtrace_ops, entry);
+ dump_trace(NULL, regs, NULL, regs->bp, &backtrace_ops, entry);
}
/*
if (!product)
product = "";
- printk("\n");
- printk(KERN_INFO "Pid: %d, comm: %.20s %s %s %.*s %s/%s\n",
+ printk(KERN_CONT "\n");
+ printk(KERN_DEFAULT "Pid: %d, comm: %.20s %s %s %.*s %s/%s\n",
current->pid, current->comm, print_tainted(),
init_utsname()->release,
(int)strcspn(init_utsname()->version, " "),
show_regs_common();
- printk("EIP: %04x:[<%08lx>] EFLAGS: %08lx CPU: %d\n",
+ printk(KERN_DEFAULT "EIP: %04x:[<%08lx>] EFLAGS: %08lx CPU: %d\n",
(u16)regs->cs, regs->ip, regs->flags,
smp_processor_id());
print_symbol("EIP is at %s\n", regs->ip);
- printk("EAX: %08lx EBX: %08lx ECX: %08lx EDX: %08lx\n",
+ printk(KERN_DEFAULT "EAX: %08lx EBX: %08lx ECX: %08lx EDX: %08lx\n",
regs->ax, regs->bx, regs->cx, regs->dx);
- printk("ESI: %08lx EDI: %08lx EBP: %08lx ESP: %08lx\n",
+ printk(KERN_DEFAULT "ESI: %08lx EDI: %08lx EBP: %08lx ESP: %08lx\n",
regs->si, regs->di, regs->bp, sp);
- printk(" DS: %04x ES: %04x FS: %04x GS: %04x SS: %04x\n",
+ printk(KERN_DEFAULT " DS: %04x ES: %04x FS: %04x GS: %04x SS: %04x\n",
(u16)regs->ds, (u16)regs->es, (u16)regs->fs, gs, ss);
if (!all)
cr2 = read_cr2();
cr3 = read_cr3();
cr4 = read_cr4_safe();
- printk("CR0: %08lx CR2: %08lx CR3: %08lx CR4: %08lx\n",
+ printk(KERN_DEFAULT "CR0: %08lx CR2: %08lx CR3: %08lx CR4: %08lx\n",
cr0, cr2, cr3, cr4);
get_debugreg(d0, 0);
get_debugreg(d1, 1);
get_debugreg(d2, 2);
get_debugreg(d3, 3);
- printk("DR0: %08lx DR1: %08lx DR2: %08lx DR3: %08lx\n",
+ printk(KERN_DEFAULT "DR0: %08lx DR1: %08lx DR2: %08lx DR3: %08lx\n",
d0, d1, d2, d3);
get_debugreg(d6, 6);
get_debugreg(d7, 7);
- printk("DR6: %08lx DR7: %08lx\n",
+ printk(KERN_DEFAULT "DR6: %08lx DR7: %08lx\n",
d6, d7);
}
unsigned int ds, cs, es;
show_regs_common();
- printk(KERN_INFO "RIP: %04lx:[<%016lx>] ", regs->cs & 0xffff, regs->ip);
+ printk(KERN_DEFAULT "RIP: %04lx:[<%016lx>] ", regs->cs & 0xffff, regs->ip);
printk_address(regs->ip, 1);
- printk(KERN_INFO "RSP: %04lx:%016lx EFLAGS: %08lx\n", regs->ss,
+ printk(KERN_DEFAULT "RSP: %04lx:%016lx EFLAGS: %08lx\n", regs->ss,
regs->sp, regs->flags);
- printk(KERN_INFO "RAX: %016lx RBX: %016lx RCX: %016lx\n",
+ printk(KERN_DEFAULT "RAX: %016lx RBX: %016lx RCX: %016lx\n",
regs->ax, regs->bx, regs->cx);
- printk(KERN_INFO "RDX: %016lx RSI: %016lx RDI: %016lx\n",
+ printk(KERN_DEFAULT "RDX: %016lx RSI: %016lx RDI: %016lx\n",
regs->dx, regs->si, regs->di);
- printk(KERN_INFO "RBP: %016lx R08: %016lx R09: %016lx\n",
+ printk(KERN_DEFAULT "RBP: %016lx R08: %016lx R09: %016lx\n",
regs->bp, regs->r8, regs->r9);
- printk(KERN_INFO "R10: %016lx R11: %016lx R12: %016lx\n",
+ printk(KERN_DEFAULT "R10: %016lx R11: %016lx R12: %016lx\n",
regs->r10, regs->r11, regs->r12);
- printk(KERN_INFO "R13: %016lx R14: %016lx R15: %016lx\n",
+ printk(KERN_DEFAULT "R13: %016lx R14: %016lx R15: %016lx\n",
regs->r13, regs->r14, regs->r15);
asm("movl %%ds,%0" : "=r" (ds));
cr3 = read_cr3();
cr4 = read_cr4();
- printk(KERN_INFO "FS: %016lx(%04x) GS:%016lx(%04x) knlGS:%016lx\n",
+ printk(KERN_DEFAULT "FS: %016lx(%04x) GS:%016lx(%04x) knlGS:%016lx\n",
fs, fsindex, gs, gsindex, shadowgs);
- printk(KERN_INFO "CS: %04x DS: %04x ES: %04x CR0: %016lx\n", cs, ds,
+ printk(KERN_DEFAULT "CS: %04x DS: %04x ES: %04x CR0: %016lx\n", cs, ds,
es, cr0);
- printk(KERN_INFO "CR2: %016lx CR3: %016lx CR4: %016lx\n", cr2, cr3,
+ printk(KERN_DEFAULT "CR2: %016lx CR3: %016lx CR4: %016lx\n", cr2, cr3,
cr4);
get_debugreg(d0, 0);
get_debugreg(d1, 1);
get_debugreg(d2, 2);
- printk(KERN_INFO "DR0: %016lx DR1: %016lx DR2: %016lx\n", d0, d1, d2);
+ printk(KERN_DEFAULT "DR0: %016lx DR1: %016lx DR2: %016lx\n", d0, d1, d2);
get_debugreg(d3, 3);
get_debugreg(d6, 6);
get_debugreg(d7, 7);
- printk(KERN_INFO "DR3: %016lx DR6: %016lx DR7: %016lx\n", d3, d6, d7);
+ printk(KERN_DEFAULT "DR3: %016lx DR6: %016lx DR7: %016lx\n", d3, d6, d7);
}
void show_regs(struct pt_regs *regs)
hrtimer_cancel(&apic->lapic_timer.timer);
update_divide_count(apic);
start_apic_timer(apic);
+ apic->irr_pending = true;
}
void __kvm_migrate_apic_timer(struct kvm_vcpu *vcpu)
static void FNAME(invlpg)(struct kvm_vcpu *vcpu, gva_t gva)
{
struct kvm_shadow_walk_iterator iterator;
- pt_element_t gpte;
- gpa_t pte_gpa = -1;
int level;
u64 *sptep;
int need_flush = 0;
if (level == PT_PAGE_TABLE_LEVEL ||
((level == PT_DIRECTORY_LEVEL && is_large_pte(*sptep))) ||
((level == PT_PDPE_LEVEL && is_large_pte(*sptep)))) {
- struct kvm_mmu_page *sp = page_header(__pa(sptep));
-
- pte_gpa = (sp->gfn << PAGE_SHIFT);
- pte_gpa += (sptep - sp->spt) * sizeof(pt_element_t);
if (is_shadow_present_pte(*sptep)) {
rmap_remove(vcpu->kvm, sptep);
if (need_flush)
kvm_flush_remote_tlbs(vcpu->kvm);
spin_unlock(&vcpu->kvm->mmu_lock);
-
- if (pte_gpa == -1)
- return;
- if (kvm_read_guest_atomic(vcpu->kvm, pte_gpa, &gpte,
- sizeof(pt_element_t)))
- return;
- if (is_present_gpte(gpte) && (gpte & PT_ACCESSED_MASK)) {
- if (mmu_topup_memory_caches(vcpu))
- return;
- kvm_mmu_pte_write(vcpu, pte_gpa, (const u8 *)&gpte,
- sizeof(pt_element_t), 0);
- }
}
static gpa_t FNAME(gva_to_gpa)(struct kvm_vcpu *vcpu, gva_t vaddr)
events->sipi_vector = vcpu->arch.sipi_vector;
- events->flags = 0;
+ events->flags = (KVM_VCPUEVENT_VALID_NMI_PENDING
+ | KVM_VCPUEVENT_VALID_SIPI_VECTOR);
vcpu_put(vcpu);
}
static int kvm_vcpu_ioctl_x86_set_vcpu_events(struct kvm_vcpu *vcpu,
struct kvm_vcpu_events *events)
{
- if (events->flags)
+ if (events->flags & ~(KVM_VCPUEVENT_VALID_NMI_PENDING
+ | KVM_VCPUEVENT_VALID_SIPI_VECTOR))
return -EINVAL;
vcpu_load(vcpu);
kvm_pic_clear_isr_ack(vcpu->kvm);
vcpu->arch.nmi_injected = events->nmi.injected;
- vcpu->arch.nmi_pending = events->nmi.pending;
+ if (events->flags & KVM_VCPUEVENT_VALID_NMI_PENDING)
+ vcpu->arch.nmi_pending = events->nmi.pending;
kvm_x86_ops->set_nmi_mask(vcpu, events->nmi.masked);
- vcpu->arch.sipi_vector = events->sipi_vector;
+ if (events->flags & KVM_VCPUEVENT_VALID_SIPI_VECTOR)
+ vcpu->arch.sipi_vector = events->sipi_vector;
vcpu_put(vcpu);
switch (e->type) {
case KMEMCHECK_ERROR_INVALID_ACCESS:
- printk(KERN_ERR "WARNING: kmemcheck: Caught %d-bit read "
- "from %s memory (%p)\n",
+ printk(KERN_WARNING "WARNING: kmemcheck: Caught %d-bit read from %s memory (%p)\n",
8 * e->size, e->state < ARRAY_SIZE(desc) ?
desc[e->state] : "(invalid shadow state)",
(void *) e->address);
- printk(KERN_INFO);
+ printk(KERN_WARNING);
for (i = 0; i < SHADOW_COPY_SIZE; ++i)
- printk("%02x", e->memory_copy[i]);
- printk("\n");
+ printk(KERN_CONT "%02x", e->memory_copy[i]);
+ printk(KERN_CONT "\n");
- printk(KERN_INFO);
+ printk(KERN_WARNING);
for (i = 0; i < SHADOW_COPY_SIZE; ++i) {
if (e->shadow_copy[i] < ARRAY_SIZE(short_desc))
- printk(" %c", short_desc[e->shadow_copy[i]]);
+ printk(KERN_CONT " %c", short_desc[e->shadow_copy[i]]);
else
- printk(" ?");
+ printk(KERN_CONT " ?");
}
- printk("\n");
- printk(KERN_INFO "%*c\n", 2 + 2
+ printk(KERN_CONT "\n");
+ printk(KERN_WARNING "%*c\n", 2 + 2
* (int) (e->address & (SHADOW_COPY_SIZE - 1)), '^');
break;
case KMEMCHECK_ERROR_BUG:
}
}
-void __init update_res(struct pci_root_info *info, size_t start,
+void __devinit update_res(struct pci_root_info *info, size_t start,
size_t end, unsigned long flags, int merge)
{
int i;
od_sver = 19;
}
-/^GNU/ {
- split($3, ver, ".");
+/^GNU objdump/ {
+ verstr = ""
+ for (i = 3; i <= NF; i++)
+ if (match($(i), "^[0-9]")) {
+ verstr = $(i);
+ break;
+ }
+ if (verstr == "") {
+ printf("Warning: Failed to find objdump version number.\n");
+ exit 0;
+ }
+ split(verstr, ver, ".");
if (ver[1] > od_ver ||
(ver[1] == od_ver && ver[2] >= od_sver)) {
exit 1;
} else {
printf("Warning: objdump version %s is older than %d.%d\n",
- $4, od_ver, od_sver);
+ verstr, od_ver, od_sver);
print("Warning: Skipping posttest.");
# Logic is inverted, because we just skip test without error.
exit 0;
* our current implementations need. If we'll ever need
* more the interface will need revisiting.
*/
- page = alloc_page(GFP_KERNEL | __GFP_ZERO);
+ page = alloc_page(gfp_mask | __GFP_ZERO);
if (!page)
goto out_free_bio;
if (bio_add_pc_page(q, bio, page, sector_size, 0) < sector_size)
/**
* blk_stack_limits - adjust queue_limits for stacked devices
- * @t: the stacking driver limits (top)
- * @b: the underlying queue limits (bottom)
+ * @t: the stacking driver limits (top device)
+ * @b: the underlying queue limits (bottom, component device)
* @offset: offset to beginning of data within component device
*
* Description:
- * Merges two queue_limit structs. Returns 0 if alignment didn't
- * change. Returns -1 if adding the bottom device caused
- * misalignment.
+ * This function is used by stacking drivers like MD and DM to ensure
+ * that all component devices have compatible block sizes and
+ * alignments. The stacking driver must provide a queue_limits
+ * struct (top) and then iteratively call the stacking function for
+ * all component (bottom) devices. The stacking function will
+ * attempt to combine the values and ensure proper alignment.
+ *
+ * Returns 0 if the top and bottom queue_limits are compatible. The
+ * top device's block sizes and alignment offsets may be adjusted to
+ * ensure alignment with the bottom device. If no compatible sizes
+ * and alignments exist, -1 is returned and the resulting top
+ * queue_limits will have the misaligned flag set to indicate that
+ * the alignment_offset is undefined.
*/
int blk_stack_limits(struct queue_limits *t, struct queue_limits *b,
sector_t offset)
{
- int ret;
-
- ret = 0;
+ sector_t alignment;
+ unsigned int top, bottom;
t->max_sectors = min_not_zero(t->max_sectors, b->max_sectors);
t->max_hw_sectors = min_not_zero(t->max_hw_sectors, b->max_hw_sectors);
t->max_segment_size = min_not_zero(t->max_segment_size,
b->max_segment_size);
+ alignment = queue_limit_alignment_offset(b, offset);
+
+ /* Bottom device has different alignment. Check that it is
+ * compatible with the current top alignment.
+ */
+ if (t->alignment_offset != alignment) {
+
+ top = max(t->physical_block_size, t->io_min)
+ + t->alignment_offset;
+ bottom = max(b->physical_block_size, b->io_min) + alignment;
+
+ /* Verify that top and bottom intervals line up */
+ if (max(top, bottom) & (min(top, bottom) - 1))
+ t->misaligned = 1;
+ }
+
t->logical_block_size = max(t->logical_block_size,
b->logical_block_size);
b->physical_block_size);
t->io_min = max(t->io_min, b->io_min);
+ t->io_opt = lcm(t->io_opt, b->io_opt);
+
t->no_cluster |= b->no_cluster;
t->discard_zeroes_data &= b->discard_zeroes_data;
- /* Bottom device offset aligned? */
- if (offset &&
- (offset & (b->physical_block_size - 1)) != b->alignment_offset) {
+ /* Physical block size a multiple of the logical block size? */
+ if (t->physical_block_size & (t->logical_block_size - 1)) {
+ t->physical_block_size = t->logical_block_size;
t->misaligned = 1;
- ret = -1;
}
- /*
- * Temporarily disable discard granularity. It's currently buggy
- * since we default to 0 for discard_granularity, hence this
- * "failure" will always trigger for non-zero offsets.
- */
-#if 0
- if (offset &&
- (offset & (b->discard_granularity - 1)) != b->discard_alignment) {
- t->discard_misaligned = 1;
- ret = -1;
+ /* Minimum I/O a multiple of the physical block size? */
+ if (t->io_min & (t->physical_block_size - 1)) {
+ t->io_min = t->physical_block_size;
+ t->misaligned = 1;
}
-#endif
-
- /* If top has no alignment offset, inherit from bottom */
- if (!t->alignment_offset)
- t->alignment_offset =
- b->alignment_offset & (b->physical_block_size - 1);
- if (!t->discard_alignment)
- t->discard_alignment =
- b->discard_alignment & (b->discard_granularity - 1);
-
- /* Top device aligned on logical block boundary? */
- if (t->alignment_offset & (t->logical_block_size - 1)) {
+ /* Optimal I/O a multiple of the physical block size? */
+ if (t->io_opt & (t->physical_block_size - 1)) {
+ t->io_opt = 0;
t->misaligned = 1;
- ret = -1;
}
- /* Find lcm() of optimal I/O size and granularity */
- t->io_opt = lcm(t->io_opt, b->io_opt);
- t->discard_granularity = lcm(t->discard_granularity,
- b->discard_granularity);
+ /* Find lowest common alignment_offset */
+ t->alignment_offset = lcm(t->alignment_offset, alignment)
+ & (max(t->physical_block_size, t->io_min) - 1);
- /* Verify that optimal I/O size is a multiple of io_min */
- if (t->io_min && t->io_opt % t->io_min)
- ret = -1;
+ /* Verify that new alignment_offset is on a logical block boundary */
+ if (t->alignment_offset & (t->logical_block_size - 1))
+ t->misaligned = 1;
+
+ /* Discard alignment and granularity */
+ if (b->discard_granularity) {
+ unsigned int granularity = b->discard_granularity;
+ offset &= granularity - 1;
+
+ alignment = (granularity + b->discard_alignment - offset)
+ & (granularity - 1);
+
+ if (t->discard_granularity != 0 &&
+ t->discard_alignment != alignment) {
+ top = t->discard_granularity + t->discard_alignment;
+ bottom = b->discard_granularity + alignment;
+
+ /* Verify that top and bottom intervals line up */
+ if (max(top, bottom) & (min(top, bottom) - 1))
+ t->discard_misaligned = 1;
+ }
+
+ t->max_discard_sectors = min_not_zero(t->max_discard_sectors,
+ b->max_discard_sectors);
+ t->discard_granularity = max(t->discard_granularity,
+ b->discard_granularity);
+ t->discard_alignment = lcm(t->discard_alignment, alignment) &
+ (t->discard_granularity - 1);
+ }
- return ret;
+ return t->misaligned ? -1 : 0;
}
EXPORT_SYMBOL(blk_stack_limits);
/* Root service tree for cfq_groups */
struct cfq_rb_root grp_service_tree;
struct cfq_group root_group;
- /* Number of active cfq groups on group service tree */
- int nr_groups;
/*
* The priority currently being served
static struct cfq_rb_root *service_tree_for(struct cfq_group *cfqg,
enum wl_prio_t prio,
- enum wl_type_t type,
- struct cfq_data *cfqd)
+ enum wl_type_t type)
{
if (!cfqg)
return NULL;
__cfq_group_service_tree_add(st, cfqg);
cfqg->on_st = true;
- cfqd->nr_groups++;
st->total_weight += cfqg->weight;
}
cfq_log_cfqg(cfqd, cfqg, "del_from_rr group");
cfqg->on_st = false;
- cfqd->nr_groups--;
st->total_weight -= cfqg->weight;
if (!RB_EMPTY_NODE(&cfqg->rb_node))
cfq_rb_erase(&cfqg->rb_node, st);
#endif
service_tree = service_tree_for(cfqq->cfqg, cfqq_prio(cfqq),
- cfqq_type(cfqq), cfqd);
+ cfqq_type(cfqq));
if (cfq_class_idle(cfqq)) {
rb_key = CFQ_IDLE_DELAY;
parent = rb_last(&service_tree->rb);
struct cfq_io_context *cic;
struct cfq_queue *cfqq;
- /* Deny merge if bio and rq don't belong to same cfq group */
- if ((RQ_CFQQ(rq))->cfqg != cfq_get_cfqg(cfqd, 0))
- return false;
/*
* Disallow merge of a sync bio into an async request.
*/
{
struct cfq_rb_root *service_tree =
service_tree_for(cfqd->serving_group, cfqd->serving_prio,
- cfqd->serving_type, cfqd);
+ cfqd->serving_type);
if (!cfqd->rq_queued)
return NULL;
#define CFQQ_SEEKY(cfqq) ((cfqq)->seek_mean > CFQQ_SEEK_THR)
static inline int cfq_rq_close(struct cfq_data *cfqd, struct cfq_queue *cfqq,
- struct request *rq)
+ struct request *rq, bool for_preempt)
{
sector_t sdist = cfqq->seek_mean;
if (!sample_valid(cfqq->seek_samples))
sdist = CFQQ_SEEK_THR;
+ /* if seek_mean is big, using it as close criteria is meaningless */
+ if (sdist > CFQQ_SEEK_THR && !for_preempt)
+ sdist = CFQQ_SEEK_THR;
+
return cfq_dist_from_last(cfqd, rq) <= sdist;
}
* will contain the closest sector.
*/
__cfqq = rb_entry(parent, struct cfq_queue, p_node);
- if (cfq_rq_close(cfqd, cur_cfqq, __cfqq->next_rq))
+ if (cfq_rq_close(cfqd, cur_cfqq, __cfqq->next_rq, false))
return __cfqq;
if (blk_rq_pos(__cfqq->next_rq) < sector)
return NULL;
__cfqq = rb_entry(node, struct cfq_queue, p_node);
- if (cfq_rq_close(cfqd, cur_cfqq, __cfqq->next_rq))
+ if (cfq_rq_close(cfqd, cur_cfqq, __cfqq->next_rq, false))
return __cfqq;
return NULL;
}
static enum wl_type_t cfq_choose_wl(struct cfq_data *cfqd,
- struct cfq_group *cfqg, enum wl_prio_t prio,
- bool prio_changed)
+ struct cfq_group *cfqg, enum wl_prio_t prio)
{
struct cfq_queue *queue;
int i;
unsigned long lowest_key = 0;
enum wl_type_t cur_best = SYNC_NOIDLE_WORKLOAD;
- if (prio_changed) {
- /*
- * When priorities switched, we prefer starting
- * from SYNC_NOIDLE (first choice), or just SYNC
- * over ASYNC
- */
- if (service_tree_for(cfqg, prio, cur_best, cfqd)->count)
- return cur_best;
- cur_best = SYNC_WORKLOAD;
- if (service_tree_for(cfqg, prio, cur_best, cfqd)->count)
- return cur_best;
-
- return ASYNC_WORKLOAD;
- }
-
- for (i = 0; i < 3; ++i) {
- /* otherwise, select the one with lowest rb_key */
- queue = cfq_rb_first(service_tree_for(cfqg, prio, i, cfqd));
+ for (i = 0; i <= SYNC_WORKLOAD; ++i) {
+ /* select the one with lowest rb_key */
+ queue = cfq_rb_first(service_tree_for(cfqg, prio, i));
if (queue &&
(!key_valid || time_before(queue->rb_key, lowest_key))) {
lowest_key = queue->rb_key;
static void choose_service_tree(struct cfq_data *cfqd, struct cfq_group *cfqg)
{
- enum wl_prio_t previous_prio = cfqd->serving_prio;
- bool prio_changed;
unsigned slice;
unsigned count;
struct cfq_rb_root *st;
* (SYNC, SYNC_NOIDLE, ASYNC), and to compute a workload
* expiration time
*/
- prio_changed = (cfqd->serving_prio != previous_prio);
- st = service_tree_for(cfqg, cfqd->serving_prio, cfqd->serving_type,
- cfqd);
+ st = service_tree_for(cfqg, cfqd->serving_prio, cfqd->serving_type);
count = st->count;
/*
- * If priority didn't change, check workload expiration,
- * and that we still have other queues ready
+ * check workload expiration, and that we still have other queues ready
*/
- if (!prio_changed && count &&
- !time_after(jiffies, cfqd->workload_expires))
+ if (count && !time_after(jiffies, cfqd->workload_expires))
return;
/* otherwise select new workload type */
cfqd->serving_type =
- cfq_choose_wl(cfqd, cfqg, cfqd->serving_prio, prio_changed);
- st = service_tree_for(cfqg, cfqd->serving_prio, cfqd->serving_type,
- cfqd);
+ cfq_choose_wl(cfqd, cfqg, cfqd->serving_prio);
+ st = service_tree_for(cfqg, cfqd->serving_prio, cfqd->serving_type);
count = st->count;
/*
* if this request is as-good as one we would expect from the
* current cfqq, let it preempt
*/
- if (cfq_rq_close(cfqd, cfqq, rq))
+ if (cfq_rq_close(cfqd, cfqq, rq, true))
return true;
return false;
err += test(4, &tests);
if (NDISKS > 5)
err += test(5, &tests);
+ /* the 11 and 12 disk cases are special for ioatdma (p-disabled
+ * q-continuation without extended descriptor)
+ */
+ if (NDISKS > 12) {
+ err += test(11, &tests);
+ err += test(12, &tests);
+ }
err += test(NDISKS, &tests);
pr("\n");
source "drivers/message/fusion/Kconfig"
-source "drivers/ieee1394/Kconfig"
+source "drivers/firewire/Kconfig"
source "drivers/message/i2o/Kconfig"
#ifdef CONFIG_ACPI_SLEEP
static u32 acpi_target_sleep_state = ACPI_STATE_S0;
+/*
+ * According to the ACPI specification the BIOS should make sure that ACPI is
+ * enabled and SCI_EN bit is set on wake-up from S1 - S3 sleep states. Still,
+ * some BIOSes don't do that and therefore we use acpi_enable() to enable ACPI
+ * on such systems during resume. Unfortunately that doesn't help in
+ * particularly pathological cases in which SCI_EN has to be set directly on
+ * resume, although the specification states very clearly that this flag is
+ * owned by the hardware. The set_sci_en_on_resume variable will be set in such
+ * cases.
+ */
+static bool set_sci_en_on_resume;
+
+void __init acpi_set_sci_en_on_resume(void)
+{
+ set_sci_en_on_resume = true;
+}
+
/*
* ACPI 1.0 wants us to execute _PTS before suspending devices, so we allow the
* user to request that behavior by using the 'acpi_old_suspend_ordering'
#endif /* CONFIG_ACPI_SLEEP */
#ifdef CONFIG_SUSPEND
-/*
- * According to the ACPI specification the BIOS should make sure that ACPI is
- * enabled and SCI_EN bit is set on wake-up from S1 - S3 sleep states. Still,
- * some BIOSes don't do that and therefore we use acpi_enable() to enable ACPI
- * on such systems during resume. Unfortunately that doesn't help in
- * particularly pathological cases in which SCI_EN has to be set directly on
- * resume, although the specification states very clearly that this flag is
- * owned by the hardware. The set_sci_en_on_resume variable will be set in such
- * cases.
- */
-static bool set_sci_en_on_resume;
-
extern void do_suspend_lowlevel(void);
static u32 acpi_suspend_states[] = {
sprintf(name, "acpi_video%d", count++);
device->backlight = backlight_device_register(name,
NULL, device, &acpi_backlight_ops);
- device->backlight->props.max_brightness = device->brightness->count-3;
kfree(name);
+ if (IS_ERR(device->backlight))
+ return;
+ device->backlight->props.max_brightness = device->brightness->count-3;
result = sysfs_create_link(&device->backlight->dev.kobj,
&device->dev->dev.kobj, "device");
unsigned long long level_current, level_next;
int result = -EINVAL;
+ /* no warning message if acpi_backlight=vendor is used */
+ if (!acpi_video_backlight_support())
+ return 0;
+
if (!device->brightness)
goto out;
static struct DAC960_privdata DAC960_LP_privdata = {
.HardwareType = DAC960_LP_Controller,
- .FirmwareType = DAC960_LP_Controller,
+ .FirmwareType = DAC960_V2_Controller,
.InterruptHandler = DAC960_LP_InterruptHandler,
.MemoryWindowSize = DAC960_LP_RegisterWindowSize,
};
part_stat_unlock();
}
-/*
- * Ensure we don't create aliases in VI caches
- */
-static inline void
-killalias(struct bio *bio)
-{
- struct bio_vec *bv;
- int i;
-
- if (bio_data_dir(bio) == READ)
- __bio_for_each_segment(bv, bio, i, 0) {
- flush_dcache_page(bv->bv_page);
- }
-}
-
void
aoecmd_ata_rsp(struct sk_buff *skb)
{
if (buf->flags & BUFFL_FAIL)
bio_endio(buf->bio, -EIO);
else {
- killalias(buf->bio);
+ bio_flush_dcache_pages(buf->bio);
bio_endio(buf->bio, 0);
}
mempool_free(buf, d->bufpool);
/* drbd_proc.c */
extern struct proc_dir_entry *drbd_proc;
-extern struct file_operations drbd_proc_fops;
+extern const struct file_operations drbd_proc_fops;
extern const char *drbd_conn_str(enum drbd_conns s);
extern const char *drbd_role_str(enum drbd_role s);
*/
#include <linux/module.h>
-#include <linux/version.h>
#include <linux/drbd.h>
#include <asm/uaccess.h>
#include <asm/types.h>
DEFINE_RATELIMIT_STATE(drbd_ratelimit_state, 5 * HZ, 5);
-static struct block_device_operations drbd_ops = {
+static const struct block_device_operations drbd_ops = {
.owner = THIS_MODULE,
.open = drbd_open,
.release = drbd_release,
{
long refresh;
- if (--rsp->count < 0) {
+ if (!rsp->count--) {
get_random_bytes(&refresh, sizeof(refresh));
rsp->state += refresh;
rsp->count = FAULT_RANDOM_REFRESH;
struct proc_dir_entry *drbd_proc;
-struct file_operations drbd_proc_fops = {
+const struct file_operations drbd_proc_fops = {
.owner = THIS_MODULE,
.open = drbd_proc_open,
.read = seq_read,
#include <asm/uaccess.h>
#include <net/sock.h>
-#include <linux/version.h>
#include <linux/drbd.h>
#include <linux/fs.h>
#include <linux/file.h>
*/
#include <linux/module.h>
-#include <linux/version.h>
#include <linux/drbd.h>
#include <linux/sched.h>
#include <linux/smp_lock.h>
#include <linux/mm_inline.h>
#include <linux/slab.h>
#include <linux/random.h>
-#include <linux/mm.h>
#include <linux/string.h>
#include <linux/scatterlist.h>
err = -EINVAL;
goto probe_err_2;
}
- host->dev_base = ioremap(rsc->start , rsc->end + 1);
+ host->dev_base = ioremap(rsc->start, resource_size(rsc));
if (!host->dev_base) {
printk(KERN_ERR "%s:%d ioremap fail\n",
__func__, __LINE__);
int __init agp_amd64_init(void)
{
int err = 0;
+ static int done = 0;
if (agp_off)
return -EINVAL;
+
+ if (done++)
+ return agp_bridges_found ? 0 : -ENODEV;
+
err = pci_register_driver(&agp_amd64_pci_driver);
if (err < 0)
return err;
pci_unregister_driver(&agp_amd64_pci_driver);
}
-/* On AMD64 the PCI driver needs to initialize this driver early
- for the IOMMU, so it has to be called via a backdoor. */
-#ifndef CONFIG_GART_IOMMU
module_init(agp_amd64_init);
module_exit(agp_amd64_cleanup);
-#endif
MODULE_AUTHOR("Dave Jones <davej@redhat.com>, Andi Kleen");
module_param(agp_try_unsupported, bool, 0);
goto out;
}
}
-out_unlock:
- mutex_unlock(&rng_mutex);
out:
return ret ? : err;
+out_unlock:
+ mutex_unlock(&rng_mutex);
+ goto out;
}
#ifdef CONFIG_ACPI
spmi_find_bmc();
#endif
-#ifdef CONFIG_PNP
+#ifdef CONFIG_ACPI
pnp_register_driver(&ipmi_pnp_driver);
#endif
#ifdef CONFIG_PCI
pci_unregister_driver(&ipmi_pci_driver);
#endif
-#ifdef CONFIG_PNP
+#ifdef CONFIG_ACPI
pnp_unregister_driver(&ipmi_pnp_driver);
#endif
dev_vdbg(chan2dev(chan), "is_tx_complete: %d (d%d, u%d)\n",
cookie, done ? *done : 0, used ? *used : 0);
- spin_lock_bh(atchan->lock);
+ spin_lock_bh(&atchan->lock);
last_complete = atchan->completed_cookie;
last_used = chan->cookie;
ret = dma_async_is_complete(cookie, last_complete, last_used);
}
- spin_unlock_bh(atchan->lock);
+ spin_unlock_bh(&atchan->lock);
if (done)
*done = last_complete;
dma_async_device_unregister(&base->dma_slave);
coh901318_pool_destroy(&base->pool);
free_irq(platform_get_irq(pdev, 0), base);
- kfree(base);
iounmap(base->virtbase);
+ kfree(base);
release_mem_region(pdev->resource->start,
resource_size(pdev->resource));
return 0;
goto err_kfree;
}
- memset(dw, 0, sizeof *dw);
-
dw->regs = ioremap(io->start, DW_REGLEN);
if (!dw->regs) {
err = -ENOMEM;
dma->dev = &pdev->dev;
if (!dma->chancnt) {
- dev_err(dev, "zero channels detected\n");
+ dev_err(dev, "channel enumeration error\n");
goto err_setup_interrupts;
}
* @dca: direct cache access context
* @intr_quirk: interrupt setup quirk (for ioat_v1 devices)
* @enumerate_channels: hw version specific channel enumeration
+ * @reset_hw: hw version specific channel (re)initialization
* @cleanup_tasklet: select between the v2 and v3 cleanup routines
* @timer_fn: select between the v2 and v3 timer watchdog routines
* @self_test: hardware version specific self test for each supported op type
struct dca_provider *dca;
void (*intr_quirk)(struct ioatdma_device *device);
int (*enumerate_channels)(struct ioatdma_device *device);
+ int (*reset_hw)(struct ioat_chan_common *chan);
void (*cleanup_tasklet)(unsigned long data);
void (*timer_fn)(unsigned long data);
int (*self_test)(struct ioatdma_device *device);
writeb(IOAT_CHANCMD_SUSPEND, chan->reg_base + IOAT_CHANCMD_OFFSET(ver));
}
+static inline void ioat_reset(struct ioat_chan_common *chan)
+{
+ u8 ver = chan->device->version;
+
+ writeb(IOAT_CHANCMD_RESET, chan->reg_base + IOAT_CHANCMD_OFFSET(ver));
+}
+
+static inline bool ioat_reset_pending(struct ioat_chan_common *chan)
+{
+ u8 ver = chan->device->version;
+ u8 cmd;
+
+ cmd = readb(chan->reg_base + IOAT_CHANCMD_OFFSET(ver));
+ return (cmd & IOAT_CHANCMD_RESET) == IOAT_CHANCMD_RESET;
+}
+
static inline void ioat_set_chainaddr(struct ioat_dma_chan *ioat, u64 addr)
{
struct ioat_chan_common *chan = &ioat->base;
__ioat2_start_null_desc(ioat);
}
-static void ioat2_restart_channel(struct ioat2_dma_chan *ioat)
+int ioat2_quiesce(struct ioat_chan_common *chan, unsigned long tmo)
{
- struct ioat_chan_common *chan = &ioat->base;
- unsigned long phys_complete;
+ unsigned long end = jiffies + tmo;
+ int err = 0;
u32 status;
status = ioat_chansts(chan);
if (is_ioat_active(status) || is_ioat_idle(status))
ioat_suspend(chan);
while (is_ioat_active(status) || is_ioat_idle(status)) {
+ if (end && time_after(jiffies, end)) {
+ err = -ETIMEDOUT;
+ break;
+ }
status = ioat_chansts(chan);
cpu_relax();
}
+ return err;
+}
+
+int ioat2_reset_sync(struct ioat_chan_common *chan, unsigned long tmo)
+{
+ unsigned long end = jiffies + tmo;
+ int err = 0;
+
+ ioat_reset(chan);
+ while (ioat_reset_pending(chan)) {
+ if (end && time_after(jiffies, end)) {
+ err = -ETIMEDOUT;
+ break;
+ }
+ cpu_relax();
+ }
+
+ return err;
+}
+
+static void ioat2_restart_channel(struct ioat2_dma_chan *ioat)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ unsigned long phys_complete;
+
+ ioat2_quiesce(chan, 0);
if (ioat_cleanup_preamble(chan, &phys_complete))
__cleanup(ioat, phys_complete);
spin_unlock_bh(&chan->cleanup_lock);
}
+static int ioat2_reset_hw(struct ioat_chan_common *chan)
+{
+ /* throw away whatever the channel was doing and get it initialized */
+ u32 chanerr;
+
+ ioat2_quiesce(chan, msecs_to_jiffies(100));
+
+ chanerr = readl(chan->reg_base + IOAT_CHANERR_OFFSET);
+ writel(chanerr, chan->reg_base + IOAT_CHANERR_OFFSET);
+
+ return ioat2_reset_sync(chan, msecs_to_jiffies(200));
+}
+
/**
* ioat2_enumerate_channels - find and initialize the device's channels
* @device: the device to be enumerated
(unsigned long) ioat);
ioat->xfercap_log = xfercap_log;
spin_lock_init(&ioat->ring_lock);
+ if (device->reset_hw(&ioat->base)) {
+ i = 0;
+ break;
+ }
}
dma->chancnt = i;
return i;
struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
struct ioat_chan_common *chan = &ioat->base;
struct ioat_ring_ent **ring;
- u32 chanerr;
int order;
/* have we already been set up? */
/* Setup register to interrupt and write completion status on error */
writew(IOAT_CHANCTRL_RUN, chan->reg_base + IOAT_CHANCTRL_OFFSET);
- chanerr = readl(chan->reg_base + IOAT_CHANERR_OFFSET);
- if (chanerr) {
- dev_err(to_dev(chan), "CHANERR = %x, clearing\n", chanerr);
- writel(chanerr, chan->reg_base + IOAT_CHANERR_OFFSET);
- }
-
/* allocate a completion writeback area */
/* doing 2 32bit writes to mmio since 1 64b write doesn't work */
chan->completion = pci_pool_alloc(chan->device->completion_pool,
tasklet_disable(&chan->cleanup_task);
del_timer_sync(&chan->timer);
device->cleanup_tasklet((unsigned long) ioat);
-
- /* Delay 100ms after reset to allow internal DMA logic to quiesce
- * before removing DMA descriptor resources.
- */
- writeb(IOAT_CHANCMD_RESET,
- chan->reg_base + IOAT_CHANCMD_OFFSET(chan->device->version));
- mdelay(100);
+ device->reset_hw(chan);
spin_lock_bh(&ioat->ring_lock);
descs = ioat2_ring_space(ioat);
int err;
device->enumerate_channels = ioat2_enumerate_channels;
+ device->reset_hw = ioat2_reset_hw;
device->cleanup_tasklet = ioat2_cleanup_tasklet;
device->timer_fn = ioat2_timer_event;
device->self_test = ioat_dma_self_test;
void __ioat2_issue_pending(struct ioat2_dma_chan *ioat);
void ioat2_cleanup_tasklet(unsigned long data);
void ioat2_timer_event(unsigned long data);
+int ioat2_quiesce(struct ioat_chan_common *chan, unsigned long tmo);
+int ioat2_reset_sync(struct ioat_chan_common *chan, unsigned long tmo);
extern struct kobj_type ioat2_ktype;
extern struct kmem_cache *ioat2_cache;
#endif /* IOATDMA_V2_H */
num_descs = ioat2_xferlen_to_descs(ioat, len);
/* we need 2x the number of descriptors to cover greater than 3
- * sources
+ * sources (we need 1 extra source in the q-only continuation
+ * case and 3 extra sources in the p+q continuation case.
*/
- if (src_cnt > 3 || flags & DMA_PREP_CONTINUE) {
+ if (src_cnt + dmaf_p_disabled_continue(flags) > 3 ||
+ (dmaf_continue(flags) && !dmaf_p_disabled_continue(flags))) {
with_ext = 1;
num_descs *= 2;
} else
return 0;
}
+static int ioat3_reset_hw(struct ioat_chan_common *chan)
+{
+ /* throw away whatever the channel was doing and get it
+ * initialized, with ioat3 specific workarounds
+ */
+ struct ioatdma_device *device = chan->device;
+ struct pci_dev *pdev = device->pdev;
+ u32 chanerr;
+ u16 dev_id;
+ int err;
+
+ ioat2_quiesce(chan, msecs_to_jiffies(100));
+
+ chanerr = readl(chan->reg_base + IOAT_CHANERR_OFFSET);
+ writel(chanerr, chan->reg_base + IOAT_CHANERR_OFFSET);
+
+ /* -= IOAT ver.3 workarounds =- */
+ /* Write CHANERRMSK_INT with 3E07h to mask out the errors
+ * that can cause stability issues for IOAT ver.3, and clear any
+ * pending errors
+ */
+ pci_write_config_dword(pdev, IOAT_PCI_CHANERRMASK_INT_OFFSET, 0x3e07);
+ err = pci_read_config_dword(pdev, IOAT_PCI_CHANERR_INT_OFFSET, &chanerr);
+ if (err) {
+ dev_err(&pdev->dev, "channel error register unreachable\n");
+ return err;
+ }
+ pci_write_config_dword(pdev, IOAT_PCI_CHANERR_INT_OFFSET, chanerr);
+
+ /* Clear DMAUNCERRSTS Cfg-Reg Parity Error status bit
+ * (workaround for spurious config parity error after restart)
+ */
+ pci_read_config_word(pdev, IOAT_PCI_DEVICE_ID_OFFSET, &dev_id);
+ if (dev_id == PCI_DEVICE_ID_INTEL_IOAT_TBG0)
+ pci_write_config_dword(pdev, IOAT_PCI_DMAUNCERRSTS_OFFSET, 0x10);
+
+ return ioat2_reset_sync(chan, msecs_to_jiffies(200));
+}
+
int __devinit ioat3_dma_probe(struct ioatdma_device *device, int dca)
{
struct pci_dev *pdev = device->pdev;
struct ioat_chan_common *chan;
bool is_raid_device = false;
int err;
- u16 dev_id;
u32 cap;
device->enumerate_channels = ioat2_enumerate_channels;
+ device->reset_hw = ioat3_reset_hw;
device->self_test = ioat3_dma_self_test;
dma = &device->common;
dma->device_prep_dma_memcpy = ioat2_dma_prep_memcpy_lock;
dma->device_prep_dma_xor_val = NULL;
#endif
- /* -= IOAT ver.3 workarounds =- */
- /* Write CHANERRMSK_INT with 3E07h to mask out the errors
- * that can cause stability issues for IOAT ver.3
- */
- pci_write_config_dword(pdev, IOAT_PCI_CHANERRMASK_INT_OFFSET, 0x3e07);
-
- /* Clear DMAUNCERRSTS Cfg-Reg Parity Error status bit
- * (workaround for spurious config parity error after restart)
- */
- pci_read_config_word(pdev, IOAT_PCI_DEVICE_ID_OFFSET, &dev_id);
- if (dev_id == PCI_DEVICE_ID_INTEL_IOAT_TBG0)
- pci_write_config_dword(pdev, IOAT_PCI_DMAUNCERRSTS_OFFSET, 0x10);
-
err = ioat_probe(device);
if (err)
return err;
#define IOAT_PCI_DEVICE_ID_OFFSET 0x02
#define IOAT_PCI_DMAUNCERRSTS_OFFSET 0x148
+#define IOAT_PCI_CHANERR_INT_OFFSET 0x180
#define IOAT_PCI_CHANERRMASK_INT_OFFSET 0x184
/* MMIO Device Registers */
#include <linux/dmaengine.h>
#include <linux/delay.h>
#include <linux/dma-mapping.h>
-#include <linux/dmapool.h>
#include <linux/platform_device.h>
#include <cpu/dma.h>
#include <asm/dma-sh.h>
#include "shdma.h"
/* DMA descriptor control */
-#define DESC_LAST (-1)
-#define DESC_COMP (1)
-#define DESC_NCOMP (0)
+enum sh_dmae_desc_status {
+ DESC_IDLE,
+ DESC_PREPARED,
+ DESC_SUBMITTED,
+ DESC_COMPLETED, /* completed, have to call callback */
+ DESC_WAITING, /* callback called, waiting for ack / re-submit */
+};
#define NR_DESCS_PER_CHANNEL 32
/*
*/
#define RS_DEFAULT (RS_DUAL)
+static void sh_dmae_chan_ld_cleanup(struct sh_dmae_chan *sh_chan, bool all);
+
#define SH_DMAC_CHAN_BASE(id) (dma_base_addr[id])
static void sh_dmae_writel(struct sh_dmae_chan *sh_dc, u32 data, u32 reg)
{
return ts_shift[(chcr & CHCR_TS_MASK) >> CHCR_TS_SHIFT];
}
-static void dmae_set_reg(struct sh_dmae_chan *sh_chan, struct sh_dmae_regs hw)
+static void dmae_set_reg(struct sh_dmae_chan *sh_chan, struct sh_dmae_regs *hw)
{
- sh_dmae_writel(sh_chan, hw.sar, SAR);
- sh_dmae_writel(sh_chan, hw.dar, DAR);
- sh_dmae_writel(sh_chan, hw.tcr >> calc_xmit_shift(sh_chan), TCR);
+ sh_dmae_writel(sh_chan, hw->sar, SAR);
+ sh_dmae_writel(sh_chan, hw->dar, DAR);
+ sh_dmae_writel(sh_chan, hw->tcr >> calc_xmit_shift(sh_chan), TCR);
}
static void dmae_start(struct sh_dmae_chan *sh_chan)
static dma_cookie_t sh_dmae_tx_submit(struct dma_async_tx_descriptor *tx)
{
- struct sh_desc *desc = tx_to_sh_desc(tx);
+ struct sh_desc *desc = tx_to_sh_desc(tx), *chunk, *last = desc, *c;
struct sh_dmae_chan *sh_chan = to_sh_chan(tx->chan);
+ dma_async_tx_callback callback = tx->callback;
dma_cookie_t cookie;
spin_lock_bh(&sh_chan->desc_lock);
if (cookie < 0)
cookie = 1;
- /* If desc only in the case of 1 */
- if (desc->async_tx.cookie != -EBUSY)
- desc->async_tx.cookie = cookie;
- sh_chan->common.cookie = desc->async_tx.cookie;
+ sh_chan->common.cookie = cookie;
+ tx->cookie = cookie;
+
+ /* Mark all chunks of this descriptor as submitted, move to the queue */
+ list_for_each_entry_safe(chunk, c, desc->node.prev, node) {
+ /*
+ * All chunks are on the global ld_free, so, we have to find
+ * the end of the chain ourselves
+ */
+ if (chunk != desc && (chunk->mark == DESC_IDLE ||
+ chunk->async_tx.cookie > 0 ||
+ chunk->async_tx.cookie == -EBUSY ||
+ &chunk->node == &sh_chan->ld_free))
+ break;
+ chunk->mark = DESC_SUBMITTED;
+ /* Callback goes to the last chunk */
+ chunk->async_tx.callback = NULL;
+ chunk->cookie = cookie;
+ list_move_tail(&chunk->node, &sh_chan->ld_queue);
+ last = chunk;
+ }
+
+ last->async_tx.callback = callback;
+ last->async_tx.callback_param = tx->callback_param;
- list_splice_init(&desc->tx_list, sh_chan->ld_queue.prev);
+ dev_dbg(sh_chan->dev, "submit #%d@%p on %d: %x[%d] -> %x\n",
+ tx->cookie, &last->async_tx, sh_chan->id,
+ desc->hw.sar, desc->hw.tcr, desc->hw.dar);
spin_unlock_bh(&sh_chan->desc_lock);
return cookie;
}
+/* Called with desc_lock held */
static struct sh_desc *sh_dmae_get_desc(struct sh_dmae_chan *sh_chan)
{
- struct sh_desc *desc, *_desc, *ret = NULL;
+ struct sh_desc *desc;
- spin_lock_bh(&sh_chan->desc_lock);
- list_for_each_entry_safe(desc, _desc, &sh_chan->ld_free, node) {
- if (async_tx_test_ack(&desc->async_tx)) {
+ list_for_each_entry(desc, &sh_chan->ld_free, node)
+ if (desc->mark != DESC_PREPARED) {
+ BUG_ON(desc->mark != DESC_IDLE);
list_del(&desc->node);
- ret = desc;
- break;
+ return desc;
}
- }
- spin_unlock_bh(&sh_chan->desc_lock);
-
- return ret;
-}
-
-static void sh_dmae_put_desc(struct sh_dmae_chan *sh_chan, struct sh_desc *desc)
-{
- if (desc) {
- spin_lock_bh(&sh_chan->desc_lock);
-
- list_splice_init(&desc->tx_list, &sh_chan->ld_free);
- list_add(&desc->node, &sh_chan->ld_free);
- spin_unlock_bh(&sh_chan->desc_lock);
- }
+ return NULL;
}
static int sh_dmae_alloc_chan_resources(struct dma_chan *chan)
dma_async_tx_descriptor_init(&desc->async_tx,
&sh_chan->common);
desc->async_tx.tx_submit = sh_dmae_tx_submit;
- desc->async_tx.flags = DMA_CTRL_ACK;
- INIT_LIST_HEAD(&desc->tx_list);
- sh_dmae_put_desc(sh_chan, desc);
+ desc->mark = DESC_IDLE;
spin_lock_bh(&sh_chan->desc_lock);
+ list_add(&desc->node, &sh_chan->ld_free);
sh_chan->descs_allocated++;
}
spin_unlock_bh(&sh_chan->desc_lock);
struct sh_desc *desc, *_desc;
LIST_HEAD(list);
- BUG_ON(!list_empty(&sh_chan->ld_queue));
+ /* Prepared and not submitted descriptors can still be on the queue */
+ if (!list_empty(&sh_chan->ld_queue))
+ sh_dmae_chan_ld_cleanup(sh_chan, true);
+
spin_lock_bh(&sh_chan->desc_lock);
list_splice_init(&sh_chan->ld_free, &list);
struct sh_dmae_chan *sh_chan;
struct sh_desc *first = NULL, *prev = NULL, *new;
size_t copy_size;
+ LIST_HEAD(tx_list);
+ int chunks = (len + SH_DMA_TCR_MAX) / (SH_DMA_TCR_MAX + 1);
if (!chan)
return NULL;
sh_chan = to_sh_chan(chan);
+ /* Have to lock the whole loop to protect against concurrent release */
+ spin_lock_bh(&sh_chan->desc_lock);
+
+ /*
+ * Chaining:
+ * first descriptor is what user is dealing with in all API calls, its
+ * cookie is at first set to -EBUSY, at tx-submit to a positive
+ * number
+ * if more than one chunk is needed further chunks have cookie = -EINVAL
+ * the last chunk, if not equal to the first, has cookie = -ENOSPC
+ * all chunks are linked onto the tx_list head with their .node heads
+ * only during this function, then they are immediately spliced
+ * back onto the free list in form of a chain
+ */
do {
- /* Allocate the link descriptor from DMA pool */
+ /* Allocate the link descriptor from the free list */
new = sh_dmae_get_desc(sh_chan);
if (!new) {
dev_err(sh_chan->dev,
"No free memory for link descriptor\n");
- goto err_get_desc;
+ list_for_each_entry(new, &tx_list, node)
+ new->mark = DESC_IDLE;
+ list_splice(&tx_list, &sh_chan->ld_free);
+ spin_unlock_bh(&sh_chan->desc_lock);
+ return NULL;
}
- copy_size = min(len, (size_t)SH_DMA_TCR_MAX);
+ copy_size = min(len, (size_t)SH_DMA_TCR_MAX + 1);
new->hw.sar = dma_src;
new->hw.dar = dma_dest;
new->hw.tcr = copy_size;
- if (!first)
+ if (!first) {
+ /* First desc */
+ new->async_tx.cookie = -EBUSY;
first = new;
+ } else {
+ /* Other desc - invisible to the user */
+ new->async_tx.cookie = -EINVAL;
+ }
- new->mark = DESC_NCOMP;
- async_tx_ack(&new->async_tx);
+ dev_dbg(sh_chan->dev,
+ "chaining %u of %u with %p, dst %x, cookie %d\n",
+ copy_size, len, &new->async_tx, dma_dest,
+ new->async_tx.cookie);
+
+ new->mark = DESC_PREPARED;
+ new->async_tx.flags = flags;
+ new->chunks = chunks--;
prev = new;
len -= copy_size;
dma_src += copy_size;
dma_dest += copy_size;
/* Insert the link descriptor to the LD ring */
- list_add_tail(&new->node, &first->tx_list);
+ list_add_tail(&new->node, &tx_list);
} while (len);
- new->async_tx.flags = flags; /* client is in control of this ack */
- new->async_tx.cookie = -EBUSY; /* Last desc */
+ if (new != first)
+ new->async_tx.cookie = -ENOSPC;
- return &first->async_tx;
+ /* Put them back on the free list, so, they don't get lost */
+ list_splice_tail(&tx_list, &sh_chan->ld_free);
-err_get_desc:
- sh_dmae_put_desc(sh_chan, first);
- return NULL;
+ spin_unlock_bh(&sh_chan->desc_lock);
+ return &first->async_tx;
}
-/*
- * sh_chan_ld_cleanup - Clean up link descriptors
- *
- * This function clean up the ld_queue of DMA channel.
- */
-static void sh_dmae_chan_ld_cleanup(struct sh_dmae_chan *sh_chan)
+static dma_async_tx_callback __ld_cleanup(struct sh_dmae_chan *sh_chan, bool all)
{
struct sh_desc *desc, *_desc;
+ /* Is the "exposed" head of a chain acked? */
+ bool head_acked = false;
+ dma_cookie_t cookie = 0;
+ dma_async_tx_callback callback = NULL;
+ void *param = NULL;
spin_lock_bh(&sh_chan->desc_lock);
list_for_each_entry_safe(desc, _desc, &sh_chan->ld_queue, node) {
- dma_async_tx_callback callback;
- void *callback_param;
-
- /* non send data */
- if (desc->mark == DESC_NCOMP)
+ struct dma_async_tx_descriptor *tx = &desc->async_tx;
+
+ BUG_ON(tx->cookie > 0 && tx->cookie != desc->cookie);
+ BUG_ON(desc->mark != DESC_SUBMITTED &&
+ desc->mark != DESC_COMPLETED &&
+ desc->mark != DESC_WAITING);
+
+ /*
+ * queue is ordered, and we use this loop to (1) clean up all
+ * completed descriptors, and to (2) update descriptor flags of
+ * any chunks in a (partially) completed chain
+ */
+ if (!all && desc->mark == DESC_SUBMITTED &&
+ desc->cookie != cookie)
break;
- /* send data sesc */
- callback = desc->async_tx.callback;
- callback_param = desc->async_tx.callback_param;
+ if (tx->cookie > 0)
+ cookie = tx->cookie;
- /* Remove from ld_queue list */
- list_splice_init(&desc->tx_list, &sh_chan->ld_free);
+ if (desc->mark == DESC_COMPLETED && desc->chunks == 1) {
+ BUG_ON(sh_chan->completed_cookie != desc->cookie - 1);
+ sh_chan->completed_cookie = desc->cookie;
+ }
- dev_dbg(sh_chan->dev, "link descriptor %p will be recycle.\n",
- desc);
+ /* Call callback on the last chunk */
+ if (desc->mark == DESC_COMPLETED && tx->callback) {
+ desc->mark = DESC_WAITING;
+ callback = tx->callback;
+ param = tx->callback_param;
+ dev_dbg(sh_chan->dev, "descriptor #%d@%p on %d callback\n",
+ tx->cookie, tx, sh_chan->id);
+ BUG_ON(desc->chunks != 1);
+ break;
+ }
- list_move(&desc->node, &sh_chan->ld_free);
- /* Run the link descriptor callback function */
- if (callback) {
- spin_unlock_bh(&sh_chan->desc_lock);
- dev_dbg(sh_chan->dev, "link descriptor %p callback\n",
- desc);
- callback(callback_param);
- spin_lock_bh(&sh_chan->desc_lock);
+ if (tx->cookie > 0 || tx->cookie == -EBUSY) {
+ if (desc->mark == DESC_COMPLETED) {
+ BUG_ON(tx->cookie < 0);
+ desc->mark = DESC_WAITING;
+ }
+ head_acked = async_tx_test_ack(tx);
+ } else {
+ switch (desc->mark) {
+ case DESC_COMPLETED:
+ desc->mark = DESC_WAITING;
+ /* Fall through */
+ case DESC_WAITING:
+ if (head_acked)
+ async_tx_ack(&desc->async_tx);
+ }
+ }
+
+ dev_dbg(sh_chan->dev, "descriptor %p #%d completed.\n",
+ tx, tx->cookie);
+
+ if (((desc->mark == DESC_COMPLETED ||
+ desc->mark == DESC_WAITING) &&
+ async_tx_test_ack(&desc->async_tx)) || all) {
+ /* Remove from ld_queue list */
+ desc->mark = DESC_IDLE;
+ list_move(&desc->node, &sh_chan->ld_free);
}
}
spin_unlock_bh(&sh_chan->desc_lock);
+
+ if (callback)
+ callback(param);
+
+ return callback;
+}
+
+/*
+ * sh_chan_ld_cleanup - Clean up link descriptors
+ *
+ * This function cleans up the ld_queue of DMA channel.
+ */
+static void sh_dmae_chan_ld_cleanup(struct sh_dmae_chan *sh_chan, bool all)
+{
+ while (__ld_cleanup(sh_chan, all))
+ ;
}
static void sh_chan_xfer_ld_queue(struct sh_dmae_chan *sh_chan)
{
- struct list_head *ld_node;
- struct sh_dmae_regs hw;
+ struct sh_desc *sd;
+ spin_lock_bh(&sh_chan->desc_lock);
/* DMA work check */
- if (dmae_is_busy(sh_chan))
+ if (dmae_is_busy(sh_chan)) {
+ spin_unlock_bh(&sh_chan->desc_lock);
return;
+ }
/* Find the first un-transfer desciptor */
- for (ld_node = sh_chan->ld_queue.next;
- (ld_node != &sh_chan->ld_queue)
- && (to_sh_desc(ld_node)->mark == DESC_COMP);
- ld_node = ld_node->next)
- cpu_relax();
-
- if (ld_node != &sh_chan->ld_queue) {
- /* Get the ld start address from ld_queue */
- hw = to_sh_desc(ld_node)->hw;
- dmae_set_reg(sh_chan, hw);
- dmae_start(sh_chan);
- }
+ list_for_each_entry(sd, &sh_chan->ld_queue, node)
+ if (sd->mark == DESC_SUBMITTED) {
+ /* Get the ld start address from ld_queue */
+ dmae_set_reg(sh_chan, &sd->hw);
+ dmae_start(sh_chan);
+ break;
+ }
+
+ spin_unlock_bh(&sh_chan->desc_lock);
}
static void sh_dmae_memcpy_issue_pending(struct dma_chan *chan)
dma_cookie_t last_used;
dma_cookie_t last_complete;
- sh_dmae_chan_ld_cleanup(sh_chan);
+ sh_dmae_chan_ld_cleanup(sh_chan, false);
last_used = chan->cookie;
last_complete = sh_chan->completed_cookie;
- if (last_complete == -EBUSY)
- last_complete = last_used;
+ BUG_ON(last_complete < 0);
if (done)
*done = last_complete;
err = sh_dmae_rst(0);
if (err)
return err;
+#ifdef SH_DMAC_BASE1
if (shdev->pdata.mode & SHDMA_DMAOR1) {
err = sh_dmae_rst(1);
if (err)
return err;
}
+#endif
disable_irq(irq);
return IRQ_HANDLED;
}
static void dmae_do_tasklet(unsigned long data)
{
struct sh_dmae_chan *sh_chan = (struct sh_dmae_chan *)data;
- struct sh_desc *desc, *_desc, *cur_desc = NULL;
+ struct sh_desc *desc;
u32 sar_buf = sh_dmae_readl(sh_chan, SAR);
- list_for_each_entry_safe(desc, _desc,
- &sh_chan->ld_queue, node) {
- if ((desc->hw.sar + desc->hw.tcr) == sar_buf) {
- cur_desc = desc;
+ spin_lock(&sh_chan->desc_lock);
+ list_for_each_entry(desc, &sh_chan->ld_queue, node) {
+ if ((desc->hw.sar + desc->hw.tcr) == sar_buf &&
+ desc->mark == DESC_SUBMITTED) {
+ dev_dbg(sh_chan->dev, "done #%d@%p dst %u\n",
+ desc->async_tx.cookie, &desc->async_tx,
+ desc->hw.dar);
+ desc->mark = DESC_COMPLETED;
break;
}
}
+ spin_unlock(&sh_chan->desc_lock);
- if (cur_desc) {
- switch (cur_desc->async_tx.cookie) {
- case 0: /* other desc data */
- break;
- case -EBUSY: /* last desc */
- sh_chan->completed_cookie =
- cur_desc->async_tx.cookie;
- break;
- default: /* first desc ( 0 < )*/
- sh_chan->completed_cookie =
- cur_desc->async_tx.cookie - 1;
- break;
- }
- cur_desc->mark = DESC_COMP;
- }
/* Next desc */
sh_chan_xfer_ld_queue(sh_chan);
- sh_dmae_chan_ld_cleanup(sh_chan);
+ sh_dmae_chan_ld_cleanup(sh_chan, false);
}
static unsigned int get_dmae_irq(unsigned int id)
#ifndef __DMA_SHDMA_H
#define __DMA_SHDMA_H
-#include <linux/device.h>
-#include <linux/dmapool.h>
#include <linux/dmaengine.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
#define SH_DMA_TCR_MAX 0x00FFFFFF /* 16MB */
};
struct sh_desc {
- struct list_head tx_list;
struct sh_dmae_regs hw;
struct list_head node;
struct dma_async_tx_descriptor async_tx;
+ dma_cookie_t cookie;
+ int chunks;
int mark;
};
+struct device;
+
struct sh_dmae_chan {
dma_cookie_t completed_cookie; /* The maximum cookie completed */
spinlock_t desc_lock; /* Descriptor operation lock */
+menu "IEEE 1394 (FireWire) support"
+ depends on PCI || BROKEN
+ # firewire-core does not depend on PCI but is
+ # not useful without PCI controller driver
+
comment "You can enable one or both FireWire driver stacks."
-comment "See the help texts for more information."
+comment "The newer stack is recommended."
config FIREWIRE
tristate "FireWire driver stack"
To compile this driver as a module, say M here: the module will be
called firewire-core.
- This module functionally replaces ieee1394, raw1394, and video1394.
- To access it from application programs, you generally need at least
- libraw1394 v2. IIDC/DCAM applications need libdc1394 v2.
- No libraries are required to access storage devices through the
- firewire-sbp2 driver.
-
- NOTE:
- FireWire audio devices currently require the old drivers (ieee1394,
- ohci1394, raw1394).
-
config FIREWIRE_OHCI
tristate "OHCI-1394 controllers"
depends on PCI && FIREWIRE
is the only chipset in use, so say Y here.
To compile this driver as a module, say M here: The module will be
- called firewire-ohci. It replaces ohci1394 of the classic IEEE 1394
- stack.
-
- NOTE:
- If you want to install firewire-ohci and ohci1394 together, you
- should configure them only as modules and blacklist the driver(s)
- which you don't want to have auto-loaded. Add either
-
- blacklist firewire-ohci
- or
- blacklist ohci1394
- blacklist video1394
- blacklist dv1394
-
- to /etc/modprobe.conf or /etc/modprobe.d/* and update modprobe.conf
- depending on your distribution.
+ called firewire-ohci.
config FIREWIRE_OHCI_DEBUG
bool
like scanners.
To compile this driver as a module, say M here: The module will be
- called firewire-sbp2. It replaces sbp2 of the classic IEEE 1394
- stack.
+ called firewire-sbp2.
You should also enable support for disks, CD-ROMs, etc. in the SCSI
configuration section.
NOTE, this driver is not stable yet!
To compile this driver as a module, say M here: The module will be
- called firewire-net. It replaces eth1394 of the classic IEEE 1394
- stack.
+ called firewire-net.
+
+source "drivers/ieee1394/Kconfig"
+
+endmenu
struct inbound_transaction_resource *r = container_of(resource,
struct inbound_transaction_resource, resource);
- fw_send_response(client->device->card, r->request,
- RCODE_CONFLICT_ERROR);
+ if (r->request)
+ fw_send_response(client->device->card, r->request,
+ RCODE_CONFLICT_ERROR);
kfree(r);
}
failed:
kfree(r);
kfree(e);
- fw_send_response(card, request, RCODE_CONFLICT_ERROR);
+ if (request)
+ fw_send_response(card, request, RCODE_CONFLICT_ERROR);
}
static void release_address_handler(struct client *client,
r = container_of(resource, struct inbound_transaction_resource,
resource);
- if (request->length < r->length)
- r->length = request->length;
-
- if (copy_from_user(r->data, u64_to_uptr(request->data), r->length)) {
- ret = -EFAULT;
- goto out;
+ if (r->request) {
+ if (request->length < r->length)
+ r->length = request->length;
+ if (copy_from_user(r->data, u64_to_uptr(request->data),
+ r->length)) {
+ ret = -EFAULT;
+ kfree(r->request);
+ goto out;
+ }
+ fw_send_response(client->device->card, r->request,
+ request->rcode);
}
-
- fw_send_response(client->device->card, r->request, request->rcode);
out:
kfree(r);
return NULL;
}
+static bool is_enclosing_handler(struct fw_address_handler *handler,
+ unsigned long long offset, size_t length)
+{
+ return handler->offset <= offset &&
+ offset + length <= handler->offset + handler->length;
+}
+
static struct fw_address_handler *lookup_enclosing_address_handler(
struct list_head *list, unsigned long long offset, size_t length)
{
struct fw_address_handler *handler;
list_for_each_entry(handler, list, link) {
- if (handler->offset <= offset &&
- offset + length <= handler->offset + handler->length)
+ if (is_enclosing_handler(handler, offset, length))
return handler;
}
{ .start = 0xfffff0000900ULL, .end = 0x1000000000000ULL, };
#endif /* 0 */
+static bool is_in_fcp_region(u64 offset, size_t length)
+{
+ return offset >= (CSR_REGISTER_BASE | CSR_FCP_COMMAND) &&
+ offset + length <= (CSR_REGISTER_BASE | CSR_FCP_END);
+}
+
/**
* fw_core_add_address_handler - register for incoming requests
* @handler: callback
* give the details of the particular request.
*
* Return value: 0 on success, non-zero otherwise.
+ *
* The start offset of the handler's address region is determined by
* fw_core_add_address_handler() and is returned in handler->offset.
+ *
+ * Address allocations are exclusive, except for the FCP registers.
*/
int fw_core_add_address_handler(struct fw_address_handler *handler,
const struct fw_address_region *region)
handler->offset = region->start;
while (handler->offset + handler->length <= region->end) {
- other =
- lookup_overlapping_address_handler(&address_handler_list,
- handler->offset,
- handler->length);
+ if (is_in_fcp_region(handler->offset, handler->length))
+ other = NULL;
+ else
+ other = lookup_overlapping_address_handler
+ (&address_handler_list,
+ handler->offset, handler->length);
if (other != NULL) {
handler->offset += other->length;
} else {
void fw_send_response(struct fw_card *card,
struct fw_request *request, int rcode)
{
+ if (WARN_ONCE(!request, "invalid for FCP address handlers"))
+ return;
+
/* unified transaction or broadcast transaction: don't respond */
if (request->ack != ACK_PENDING ||
HEADER_DESTINATION_IS_BROADCAST(request->request_header[0])) {
}
EXPORT_SYMBOL(fw_send_response);
-void fw_core_handle_request(struct fw_card *card, struct fw_packet *p)
+static void handle_exclusive_region_request(struct fw_card *card,
+ struct fw_packet *p,
+ struct fw_request *request,
+ unsigned long long offset)
{
struct fw_address_handler *handler;
- struct fw_request *request;
- unsigned long long offset;
unsigned long flags;
int tcode, destination, source;
- if (p->ack != ACK_PENDING && p->ack != ACK_COMPLETE)
- return;
-
- request = allocate_request(p);
- if (request == NULL) {
- /* FIXME: send statically allocated busy packet. */
- return;
- }
-
- offset =
- ((unsigned long long)
- HEADER_GET_OFFSET_HIGH(p->header[1]) << 32) | p->header[2];
tcode = HEADER_GET_TCODE(p->header[0]);
destination = HEADER_GET_DESTINATION(p->header[0]);
source = HEADER_GET_SOURCE(p->header[1]);
request->data, request->length,
handler->callback_data);
}
+
+static void handle_fcp_region_request(struct fw_card *card,
+ struct fw_packet *p,
+ struct fw_request *request,
+ unsigned long long offset)
+{
+ struct fw_address_handler *handler;
+ unsigned long flags;
+ int tcode, destination, source;
+
+ if ((offset != (CSR_REGISTER_BASE | CSR_FCP_COMMAND) &&
+ offset != (CSR_REGISTER_BASE | CSR_FCP_RESPONSE)) ||
+ request->length > 0x200) {
+ fw_send_response(card, request, RCODE_ADDRESS_ERROR);
+
+ return;
+ }
+
+ tcode = HEADER_GET_TCODE(p->header[0]);
+ destination = HEADER_GET_DESTINATION(p->header[0]);
+ source = HEADER_GET_SOURCE(p->header[1]);
+
+ if (tcode != TCODE_WRITE_QUADLET_REQUEST &&
+ tcode != TCODE_WRITE_BLOCK_REQUEST) {
+ fw_send_response(card, request, RCODE_TYPE_ERROR);
+
+ return;
+ }
+
+ spin_lock_irqsave(&address_handler_lock, flags);
+ list_for_each_entry(handler, &address_handler_list, link) {
+ if (is_enclosing_handler(handler, offset, request->length))
+ handler->address_callback(card, NULL, tcode,
+ destination, source,
+ p->generation, p->speed,
+ offset, request->data,
+ request->length,
+ handler->callback_data);
+ }
+ spin_unlock_irqrestore(&address_handler_lock, flags);
+
+ fw_send_response(card, request, RCODE_COMPLETE);
+}
+
+void fw_core_handle_request(struct fw_card *card, struct fw_packet *p)
+{
+ struct fw_request *request;
+ unsigned long long offset;
+
+ if (p->ack != ACK_PENDING && p->ack != ACK_COMPLETE)
+ return;
+
+ request = allocate_request(p);
+ if (request == NULL) {
+ /* FIXME: send statically allocated busy packet. */
+ return;
+ }
+
+ offset = ((u64)HEADER_GET_OFFSET_HIGH(p->header[1]) << 32) |
+ p->header[2];
+
+ if (!is_in_fcp_region(offset, request->length))
+ handle_exclusive_region_request(card, p, request, offset);
+ else
+ handle_fcp_region_request(card, p, request, offset);
+
+}
EXPORT_SYMBOL(fw_core_handle_request);
void fw_core_handle_response(struct fw_card *card, struct fw_packet *p)
if (rest == 0)
return -EINVAL;
- /* FIXME: make packet-per-buffer/dual-buffer a context option */
while (rest > 0) {
d = context_get_descriptors(&ctx->context,
z + header_z, &d_bus);
}
version = reg_read(ohci, OHCI1394_Version) & 0x00ff00ff;
+#if 0
+ /* FIXME: make it a context option or remove dual-buffer mode */
ohci->use_dualbuffer = version >= OHCI_VERSION_1_1;
+#endif
/* dual-buffer mode is broken if more than one IR context is active */
if (dev->vendor == PCI_VENDOR_ID_AGERE &&
-menu "IEEE 1394 (FireWire) support"
- depends on PCI || BROKEN
-
-source "drivers/firewire/Kconfig"
-
config IEEE1394
tristate "Legacy alternative FireWire driver stack"
depends on PCI || BROKEN
is the core support only, you will also need to select a driver for
your IEEE 1394 adapter.
- To compile this driver as a module, say M here: the
- module will be called ieee1394.
+ To compile this driver as a module, say M here: the module will be
+ called ieee1394.
+
+ NOTE:
+ ieee1394 is superseded by the newer firewire-core driver. See
+ http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+ further information on how to switch to the new FireWire drivers.
config IEEE1394_OHCI1394
tristate "OHCI-1394 controllers"
use one of these chipsets. It should work with any OHCI-1394
compliant card, however.
- To compile this driver as a module, say M here: the
- module will be called ohci1394.
+ To compile this driver as a module, say M here: the module will be
+ called ohci1394.
NOTE:
+ ohci1394 is superseded by the newer firewire-ohci driver. See
+ http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+ further information on how to switch to the new FireWire drivers.
+
If you want to install firewire-ohci and ohci1394 together, you
should configure them only as modules and blacklist the driver(s)
which you don't want to have auto-loaded. Add either
- blacklist firewire-ohci
- or
blacklist ohci1394
blacklist video1394
blacklist dv1394
+ or
+ blacklist firewire-ohci
to /etc/modprobe.conf or /etc/modprobe.d/* and update modprobe.conf
depending on your distribution.
Instruments PCILynx chip. Note: this driver is written for revision
2 of this chip and may not work with revision 0.
- To compile this driver as a module, say M here: the
- module will be called pcilynx.
+ To compile this driver as a module, say M here: the module will be
+ called pcilynx.
Only some old and now very rare PCI and CardBus cards and
PowerMacs G3 B&W contain the PCILynx controller. Therefore
You should also enable support for disks, CD-ROMs, etc. in the SCSI
configuration section.
+ To compile this driver as a module, say M here: the module will be
+ called sbp2.
+
+ NOTE:
+ sbp2 is superseded by the newer firewire-sbp2 driver. See
+ http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+ further information on how to switch to the new FireWire drivers.
+
config IEEE1394_SBP2_PHYS_DMA
bool "Enable replacement for physical DMA in SBP2"
depends on IEEE1394_SBP2 && VIRT_TO_BUS && EXPERIMENTAL
The module is called eth1394 although it does not emulate Ethernet.
+ NOTE:
+ eth1394 is superseded by the newer firewire-net driver. See
+ http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+ further information on how to switch to the new FireWire drivers.
+
config IEEE1394_RAWIO
tristate "raw1394 userspace interface"
depends on IEEE1394
To compile this driver as a module, say M here: the module will be
called raw1394.
+ NOTE:
+ raw1394 is superseded by the newer firewire-core driver. See
+ http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+ further information on how to switch to the new FireWire drivers.
+
config IEEE1394_VIDEO1394
tristate "video1394 userspace interface"
depends on IEEE1394 && IEEE1394_OHCI1394
To compile this driver as a module, say M here: the module will be
called video1394.
+ NOTE:
+ video1394 is superseded by the newer firewire-core driver. See
+ http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+ further information on how to switch to the new FireWire drivers.
+
config IEEE1394_DV1394
tristate "dv1394 userspace interface (deprecated)"
depends on IEEE1394 && IEEE1394_OHCI1394
help
The dv1394 driver is unsupported and may be removed from Linux in a
- future release. Its functionality is now provided by raw1394 together
- with libraries such as libiec61883.
+ future release. Its functionality is now provided by either
+ raw1394 or firewire-core together with libraries such as libiec61883.
config IEEE1394_VERBOSEDEBUG
bool "Excessive debugging output"
will quickly result in large amounts of data sent to the system log.
Say Y if you really need the debugging output. Everyone else says N.
-
-endmenu
return 0;
}
+/*
+ * Only left/right direction should be used (under/over 0x8000) for
+ * forward/reverse motor direction (to keep calculation fast & simple).
+ */
+static u16 ml_calculate_direction(u16 direction, u16 force,
+ u16 new_direction, u16 new_force)
+{
+ if (!force)
+ return new_direction;
+ if (!new_force)
+ return direction;
+ return (((u32)(direction >> 1) * force +
+ (new_direction >> 1) * new_force) /
+ (force + new_force)) << 1;
+}
+
/*
* Combine two effects and apply gain.
*/
static void ml_combine_effects(struct ff_effect *effect,
struct ml_effect_state *state,
- unsigned int gain)
+ int gain)
{
struct ff_effect *new = state->effect;
unsigned int strong, weak, i;
break;
case FF_RUMBLE:
- strong = new->u.rumble.strong_magnitude * gain / 0xffff;
- weak = new->u.rumble.weak_magnitude * gain / 0xffff;
+ strong = (u32)new->u.rumble.strong_magnitude * gain / 0xffff;
+ weak = (u32)new->u.rumble.weak_magnitude * gain / 0xffff;
+
+ if (effect->u.rumble.strong_magnitude + strong)
+ effect->direction = ml_calculate_direction(
+ effect->direction,
+ effect->u.rumble.strong_magnitude,
+ new->direction, strong);
+ else if (effect->u.rumble.weak_magnitude + weak)
+ effect->direction = ml_calculate_direction(
+ effect->direction,
+ effect->u.rumble.weak_magnitude,
+ new->direction, weak);
+ else
+ effect->direction = 0;
effect->u.rumble.strong_magnitude =
min(strong + effect->u.rumble.strong_magnitude,
0xffffU);
/* here we also scale it 0x7fff => 0xffff */
i = i * gain / 0x7fff;
+ if (effect->u.rumble.strong_magnitude + i)
+ effect->direction = ml_calculate_direction(
+ effect->direction,
+ effect->u.rumble.strong_magnitude,
+ new->direction, i);
+ else
+ effect->direction = 0;
effect->u.rumble.strong_magnitude =
min(i + effect->u.rumble.strong_magnitude, 0xffffU);
effect->u.rumble.weak_magnitude =
msecs_to_jiffies(state->effect->replay.length);
state->adj_at = state->play_at;
- ml_schedule_timer(ml);
-
} else {
debug("initiated stop");
__set_bit(FF_EFFECT_ABORTING, &state->flags);
else
__clear_bit(FF_EFFECT_STARTED, &state->flags);
-
- ml_play_effects(ml);
}
+ ml_play_effects(ml);
+
return 0;
}
return 0;
}
-static void iforce_release(struct input_dev *dev)
+static void iforce_close(struct input_dev *dev)
{
struct iforce *iforce = input_get_drvdata(dev);
int i;
/* Disable force feedback playback */
iforce_send_packet(iforce, FF_CMD_ENABLE, "\001");
+ /* Wait for the command to complete */
+ wait_event_interruptible(iforce->wait,
+ !test_bit(IFORCE_XMIT_RUNNING, iforce->xmit_flags));
}
- switch (iforce->bus) {
-#ifdef CONFIG_JOYSTICK_IFORCE_USB
- case IFORCE_USB:
- usb_kill_urb(iforce->irq);
-
- /* The device was unplugged before the file
- * was released */
- if (iforce->usbdev == NULL) {
- iforce_delete_device(iforce);
- kfree(iforce);
- }
- break;
-#endif
- }
-}
-
-void iforce_delete_device(struct iforce *iforce)
-{
switch (iforce->bus) {
#ifdef CONFIG_JOYSTICK_IFORCE_USB
case IFORCE_USB:
- iforce_usb_delete(iforce);
+ usb_kill_urb(iforce->irq);
+ usb_kill_urb(iforce->out);
+ usb_kill_urb(iforce->ctrl);
break;
#endif
#ifdef CONFIG_JOYSTICK_IFORCE_232
input_dev->name = "Unknown I-Force device";
input_dev->open = iforce_open;
- input_dev->close = iforce_release;
+ input_dev->close = iforce_close;
/*
* On-device memory allocation.
struct iforce *iforce = urb->context;
if (urb->status) {
+ clear_bit(IFORCE_XMIT_RUNNING, iforce->xmit_flags);
dbg("urb->status %d, exiting", urb->status);
return;
}
return err;
}
-/* Called by iforce_delete() */
-void iforce_usb_delete(struct iforce* iforce)
-{
- usb_kill_urb(iforce->irq);
- usb_kill_urb(iforce->out);
- usb_kill_urb(iforce->ctrl);
-
- usb_free_urb(iforce->irq);
- usb_free_urb(iforce->out);
- usb_free_urb(iforce->ctrl);
-}
-
static void iforce_usb_disconnect(struct usb_interface *intf)
{
struct iforce *iforce = usb_get_intfdata(intf);
- int open = 0; /* FIXME! iforce->dev.handle->open; */
usb_set_intfdata(intf, NULL);
- if (iforce) {
- iforce->usbdev = NULL;
- input_unregister_device(iforce->dev);
- if (!open) {
- iforce_delete_device(iforce);
- kfree(iforce);
- }
- }
+ input_unregister_device(iforce->dev);
+
+ usb_free_urb(iforce->irq);
+ usb_free_urb(iforce->out);
+ usb_free_urb(iforce->ctrl);
+
+ kfree(iforce);
}
static struct usb_device_id iforce_usb_ids [] = {
/* iforce-usb.c */
void iforce_usb_xmit(struct iforce *iforce);
-void iforce_usb_delete(struct iforce *iforce);
/* iforce-main.c */
int iforce_init_device(struct iforce *iforce);
-void iforce_delete_device(struct iforce *iforce);
/* iforce-packets.c */
int iforce_control_playback(struct iforce*, u16 id, unsigned int);
#define ATKBD_CMD_GETID 0x02f2
#define ATKBD_CMD_SETREP 0x10f3
#define ATKBD_CMD_ENABLE 0x00f4
-#define ATKBD_CMD_RESET_DIS 0x00f5
+#define ATKBD_CMD_RESET_DIS 0x00f5 /* Reset to defaults and disable */
+#define ATKBD_CMD_RESET_DEF 0x00f6 /* Reset to defaults */
#define ATKBD_CMD_SETALL_MBR 0x00fa
#define ATKBD_CMD_RESET_BAT 0x02ff
#define ATKBD_CMD_RESEND 0x00fe
struct atkbd *atkbd = serio_get_drvdata(serio);
atkbd_disable(atkbd);
- ps2_command(&atkbd->ps2dev, NULL, ATKBD_CMD_RESET_BAT);
+ ps2_command(&atkbd->ps2dev, NULL, ATKBD_CMD_RESET_DEF);
}
unsigned short *keycodes;
unsigned int row_shift;
+ DECLARE_BITMAP(disabled_gpios, MATRIX_MAX_ROWS);
+
uint32_t last_key_state[MATRIX_MAX_COLS];
struct delayed_work work;
+ spinlock_t lock;
bool scan_pending;
bool stopped;
- spinlock_t lock;
};
/*
matrix_keypad_stop(keypad->input_dev);
- if (device_may_wakeup(&pdev->dev))
- for (i = 0; i < pdata->num_row_gpios; i++)
- enable_irq_wake(gpio_to_irq(pdata->row_gpios[i]));
+ if (device_may_wakeup(&pdev->dev)) {
+ for (i = 0; i < pdata->num_row_gpios; i++) {
+ if (!test_bit(i, keypad->disabled_gpios)) {
+ unsigned int gpio = pdata->row_gpios[i];
+
+ if (enable_irq_wake(gpio_to_irq(gpio)) == 0)
+ __set_bit(i, keypad->disabled_gpios);
+ }
+ }
+ }
return 0;
}
const struct matrix_keypad_platform_data *pdata = keypad->pdata;
int i;
- if (device_may_wakeup(&pdev->dev))
- for (i = 0; i < pdata->num_row_gpios; i++)
- disable_irq_wake(gpio_to_irq(pdata->row_gpios[i]));
+ if (device_may_wakeup(&pdev->dev)) {
+ for (i = 0; i < pdata->num_row_gpios; i++) {
+ if (test_and_clear_bit(i, keypad->disabled_gpios)) {
+ unsigned int gpio = pdata->row_gpios[i];
+
+ disable_irq_wake(gpio_to_irq(gpio));
+ }
+ }
+ }
matrix_keypad_start(keypad->input_dev);
u8 reg;
int ret;
-#ifdef CONFIG_LOCKDEP
- /* WORKAROUND for lockdep forcing IRQF_DISABLED on us, which
- * we don't want and can't tolerate. Although it might be
- * friendlier not to borrow this thread context...
- */
- local_irq_enable();
-#endif
-
/* Read & Clear TWL4030 pending interrupt */
ret = twl4030_kpread(kp, ®, KEYP_ISR1, 1);
*
* NOTE: we assume this host is wired to TWL4040 INT1, not INT2 ...
*/
- error = request_irq(kp->irq, do_kp_irq, 0, pdev->name, kp);
+ error = request_threaded_irq(kp->irq, NULL, do_kp_irq,
+ 0, pdev->name, kp);
if (error) {
dev_info(kp->dbg_dev, "request_irq failed for irq no=%d\n",
kp->irq);
int err;
u8 value;
-#ifdef CONFIG_LOCKDEP
- /* WORKAROUND for lockdep forcing IRQF_DISABLED on us, which
- * we don't want and can't tolerate since this is a threaded
- * IRQ and can sleep due to the i2c reads it has to issue.
- * Although it might be friendlier not to borrow this thread
- * context...
- */
- local_irq_enable();
-#endif
-
err = twl_i2c_read_u8(TWL4030_MODULE_PM_MASTER, &value,
- STS_HW_CONDITIONS);
+ STS_HW_CONDITIONS);
if (!err) {
input_report_key(pwr, KEY_POWER, value & PWR_PWRON_IRQ);
input_sync(pwr);
pwr->phys = "twl4030_pwrbutton/input0";
pwr->dev.parent = &pdev->dev;
- err = request_irq(irq, powerbutton_irq,
+ err = request_threaded_irq(irq, NULL, powerbutton_irq,
IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
"twl4030_pwrbutton", pwr);
if (err < 0) {
.driver = {
.name = "wistron-bios",
.owner = THIS_MODULE,
-#if CONFIG_PM
+#ifdef CONFIG_PM
.pm = &wistron_pm_ops,
#endif
},
config MOUSE_PS2_LIFEBOOK
bool "Fujitsu Lifebook PS/2 mouse protocol extension" if EMBEDDED
default y
- depends on MOUSE_PS2 && X86
+ depends on MOUSE_PS2 && X86 && DMI
help
Say Y here if you have a Fujitsu B-series Lifebook PS/2
TouchScreen connected to your system.
static int hgpk_register(struct psmouse *psmouse)
{
- struct input_dev *dev = psmouse->dev;
int err;
/* register handlers */
}
static const struct dmi_system_id __initconst lifebook_dmi_table[] = {
-#if defined(CONFIG_DMI) && defined(CONFIG_X86)
{
/* FLORA-ie 55mi */
.matches = {
},
},
{ }
-#endif
};
void __init lifebook_module_init(void)
if (psmouse->cleanup)
psmouse->cleanup(psmouse);
- psmouse_reset(psmouse);
+/*
+ * Reset the mouse to defaults (bare PS/2 protocol).
+ */
+ ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
/*
* Some boxes, such as HP nx7400, get terribly confused if mouse
mutex_lock(&serio_mutex);
- /*
- * Note that we handle only one event here to give swsusp
- * a chance to freeze kseriod thread. Serio events should
- * be pretty rare so we are not concerned about taking
- * performance hit.
- */
- if ((event = serio_get_event())) {
+ while ((event = serio_get_event())) {
switch (event->type) {
case SERIO_REGISTER_PORT:
static int serio_thread(void *nothing)
{
- set_freezable();
do {
serio_handle_event();
- wait_event_freezable(serio_wait,
+ wait_event_interruptible(serio_wait,
kthread_should_stop() || !list_empty(&serio_event_list));
} while (!kthread_should_stop());
if (!atomic_dec_and_lock(&mddev->active, &all_mddevs_lock))
return;
if (!mddev->raid_disks && list_empty(&mddev->disks) &&
- !mddev->hold_active) {
+ mddev->ctime == 0 && !mddev->hold_active) {
+ /* Array is not configured at all, and not held active,
+ * so destroy it */
list_del(&mddev->all_mddevs);
if (mddev->gendisk) {
/* we did a probe so need to clean up.
mddev->barriers_work = 1;
mddev->ok_start_degraded = start_dirty_degraded;
- if (start_readonly)
+ if (start_readonly && mddev->ro == 0)
mddev->ro = 2; /* read-only, but switch on first write */
err = mddev->pers->run(mddev);
set_capacity(disk, mddev->array_sectors);
- /* If there is a partially-recovered drive we need to
- * start recovery here. If we leave it to md_check_recovery,
- * it will remove the drives and not do the right thing
- */
- if (mddev->degraded && !mddev->sync_thread) {
- int spares = 0;
- list_for_each_entry(rdev, &mddev->disks, same_set)
- if (rdev->raid_disk >= 0 &&
- !test_bit(In_sync, &rdev->flags) &&
- !test_bit(Faulty, &rdev->flags))
- /* complete an interrupted recovery */
- spares++;
- if (spares && mddev->pers->sync_request) {
- mddev->recovery = 0;
- set_bit(MD_RECOVERY_RUNNING, &mddev->recovery);
- mddev->sync_thread = md_register_thread(md_do_sync,
- mddev,
- "resync");
- if (!mddev->sync_thread) {
- printk(KERN_ERR "%s: could not start resync"
- " thread...\n",
- mdname(mddev));
- /* leave the spares where they are, it shouldn't hurt */
- mddev->recovery = 0;
- }
- }
- }
md_wakeup_thread(mddev->thread);
md_wakeup_thread(mddev->sync_thread); /* possibly kick off a reshape */
mddev->minor_version = info->minor_version;
mddev->patch_version = info->patch_version;
mddev->persistent = !info->not_persistent;
+ /* ensure mddev_put doesn't delete this now that there
+ * is some minimal configuration.
+ */
+ mddev->ctime = get_seconds();
return 0;
}
mddev->major_version = MD_MAJOR_VERSION;
mddev->curr_resync = 2;
try_again:
- if (kthread_should_stop()) {
+ if (kthread_should_stop())
set_bit(MD_RECOVERY_INTR, &mddev->recovery);
+
+ if (test_bit(MD_RECOVERY_INTR, &mddev->recovery))
goto skip;
- }
for_each_mddev(mddev2, tmp) {
if (mddev2 == mddev)
continue;
unsigned long flags;
int su;
- if ((tcode != TCODE_WRITE_QUADLET_REQUEST &&
- tcode != TCODE_WRITE_BLOCK_REQUEST) ||
- offset != CSR_REGISTER_BASE + CSR_FCP_RESPONSE ||
- length == 0 ||
- (((u8 *)payload)[0] & 0xf0) != 0) {
- fw_send_response(card, request, RCODE_TYPE_ERROR);
+ if (length < 2 || (((u8 *)payload)[0] & 0xf0) != 0)
return;
- }
su = ((u8 *)payload)[1] & 0x7;
}
spin_unlock_irqrestore(&node_list_lock, flags);
- if (fdtv) {
+ if (fdtv)
avc_recv(fdtv, payload, length);
- fw_send_response(card, request, RCODE_COMPLETE);
- }
}
static struct fw_address_handler fcp_handler = {
bytes[byte] &= ~(0x03 << off);
- spin_lock_irq(&d->lock);
+ raw_spin_lock_irq(&d->lock);
if (d->status & IRQ_TYPE_EDGE_RISING)
bytes[byte] |= BIT(off + 1);
if (d->status & IRQ_TYPE_EDGE_FALLING)
bytes[byte] |= BIT(off + 0);
- spin_unlock_irq(&d->lock);
+ raw_spin_unlock_irq(&d->lock);
edge_change &= ~BIT(i);
}
#include <linux/errno.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
+#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/slab.h>
#include <linux/init.h>
memcpy_toio(lp->base, init_words + 5, sizeof(init_words) - 10);
/* Fill in the station address. */
- memcpy_toio(lp->base+SA_OFFSET, dev->dev_addr,
- sizeof(dev->dev_addr));
+ memcpy_toio(lp->base+SA_OFFSET, dev->dev_addr, ETH_ALEN);
/* The Tx-block list is written as needed. We just set up the values. */
lp->tx_cmd_link = IDLELOOP + 4;
config GELIC_WIRELESS
bool "PS3 Wireless support"
+ depends on WLAN
depends on GELIC_NET
select WIRELESS_EXT
help
config GELIC_WIRELESS_OLD_PSK_INTERFACE
bool "PS3 Wireless private PSK interface (OBSOLETE)"
depends on GELIC_WIRELESS
+ select WEXT_PRIV
help
This option retains the obsolete private interface to pass
the PSK from user space programs to the driver. The PSK
u32 tx_fc; /* Tx flow control */
int link_speed;
u8 port_type;
+ u8 transceiver;
};
extern const struct ethtool_ops be_ethtool_ops;
return status;
}
+int be_cmd_set_loopback(struct be_adapter *adapter, u8 port_num,
+ u8 loopback_type, u8 enable)
+{
+ struct be_mcc_wrb *wrb;
+ struct be_cmd_req_set_lmode *req;
+ int status;
+
+ spin_lock_bh(&adapter->mcc_lock);
+
+ wrb = wrb_from_mccq(adapter);
+ if (!wrb) {
+ status = -EBUSY;
+ goto err;
+ }
+
+ req = embedded_payload(wrb);
+
+ be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0,
+ OPCODE_LOWLEVEL_SET_LOOPBACK_MODE);
+
+ be_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_LOWLEVEL,
+ OPCODE_LOWLEVEL_SET_LOOPBACK_MODE,
+ sizeof(*req));
+
+ req->src_port = port_num;
+ req->dest_port = port_num;
+ req->loopback_type = loopback_type;
+ req->loopback_state = enable;
+
+ status = be_mcc_notify_wait(adapter);
+err:
+ spin_unlock_bh(&adapter->mcc_lock);
+ return status;
+}
+
int be_cmd_loopback_test(struct be_adapter *adapter, u32 port_num,
u32 loopback_type, u32 pkt_size, u32 num_pkts, u64 pattern)
{
be_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_LOWLEVEL,
OPCODE_LOWLEVEL_LOOPBACK_TEST, sizeof(*req));
+ req->hdr.timeout = 4;
req->pattern = cpu_to_le64(pattern);
req->src_port = cpu_to_le32(port_num);
#define OPCODE_LOWLEVEL_HOST_DDR_DMA 17
#define OPCODE_LOWLEVEL_LOOPBACK_TEST 18
+#define OPCODE_LOWLEVEL_SET_LOOPBACK_MODE 19
struct be_cmd_req_hdr {
u8 opcode; /* dword 0 */
u32 ticks_compl;
};
+struct be_cmd_req_set_lmode {
+ struct be_cmd_req_hdr hdr;
+ u8 src_port;
+ u8 dest_port;
+ u8 loopback_type;
+ u8 loopback_state;
+};
+
+struct be_cmd_resp_set_lmode {
+ struct be_cmd_resp_hdr resp_hdr;
+ u8 rsvd0[4];
+};
+
/********************** DDR DMA test *********************/
struct be_cmd_req_ddrdma_test {
struct be_cmd_req_hdr hdr;
u32 num_pkts, u64 pattern);
extern int be_cmd_ddr_dma_test(struct be_adapter *adapter, u64 pattern,
u32 byte_cnt, struct be_dma_mem *cmd);
+extern int be_cmd_set_loopback(struct be_adapter *adapter, u8 port_num,
+ u8 loopback_type, u8 enable);
#define BE_MAC_LOOPBACK 0x0
#define BE_PHY_LOOPBACK 0x1
#define BE_ONE_PORT_EXT_LOOPBACK 0x2
+#define BE_NO_LOOPBACK 0xff
static void
be_get_drvinfo(struct net_device *netdev, struct ethtool_drvinfo *drvinfo)
status = be_cmd_read_port_type(adapter, adapter->port_num,
&connector);
- switch (connector) {
- case 7:
- ecmd->port = PORT_FIBRE;
- break;
- default:
- ecmd->port = PORT_TP;
- break;
+ if (!status) {
+ switch (connector) {
+ case 7:
+ ecmd->port = PORT_FIBRE;
+ ecmd->transceiver = XCVR_EXTERNAL;
+ break;
+ case 0:
+ ecmd->port = PORT_TP;
+ ecmd->transceiver = XCVR_EXTERNAL;
+ break;
+ default:
+ ecmd->port = PORT_TP;
+ ecmd->transceiver = XCVR_INTERNAL;
+ break;
+ }
+ } else {
+ ecmd->port = PORT_AUI;
+ ecmd->transceiver = XCVR_INTERNAL;
}
/* Save for future use */
adapter->link_speed = ecmd->speed;
adapter->port_type = ecmd->port;
+ adapter->transceiver = ecmd->transceiver;
} else {
ecmd->speed = adapter->link_speed;
ecmd->port = adapter->port_type;
+ ecmd->transceiver = adapter->transceiver;
}
ecmd->duplex = DUPLEX_FULL;
ecmd->autoneg = AUTONEG_DISABLE;
- ecmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_TP);
ecmd->phy_address = adapter->port_num;
- ecmd->transceiver = XCVR_INTERNAL;
+ switch (ecmd->port) {
+ case PORT_FIBRE:
+ ecmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
+ break;
+ case PORT_TP:
+ ecmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_TP);
+ break;
+ case PORT_AUI:
+ ecmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_AUI);
+ break;
+ }
return 0;
}
return ret;
}
+static u64 be_loopback_test(struct be_adapter *adapter, u8 loopback_type,
+ u64 *status)
+{
+ be_cmd_set_loopback(adapter, adapter->port_num,
+ loopback_type, 1);
+ *status = be_cmd_loopback_test(adapter, adapter->port_num,
+ loopback_type, 1500,
+ 2, 0xabc);
+ be_cmd_set_loopback(adapter, adapter->port_num,
+ BE_NO_LOOPBACK, 1);
+ return *status;
+}
+
static void
be_self_test(struct net_device *netdev, struct ethtool_test *test, u64 *data)
{
memset(data, 0, sizeof(u64) * ETHTOOL_TESTS_NUM);
if (test->flags & ETH_TEST_FL_OFFLINE) {
- data[0] = be_cmd_loopback_test(adapter, adapter->port_num,
- BE_MAC_LOOPBACK, 1500,
- 2, 0xabc);
- if (data[0] != 0)
+ if (be_loopback_test(adapter, BE_MAC_LOOPBACK,
+ &data[0]) != 0) {
test->flags |= ETH_TEST_FL_FAILED;
-
- data[1] = be_cmd_loopback_test(adapter, adapter->port_num,
- BE_PHY_LOOPBACK, 1500,
- 2, 0xabc);
- if (data[1] != 0)
+ }
+ if (be_loopback_test(adapter, BE_PHY_LOOPBACK,
+ &data[1]) != 0) {
test->flags |= ETH_TEST_FL_FAILED;
-
- data[2] = be_cmd_loopback_test(adapter, adapter->port_num,
- BE_ONE_PORT_EXT_LOOPBACK,
- 1500, 2, 0xabc);
- if (data[2] != 0)
+ }
+ if (be_loopback_test(adapter, BE_ONE_PORT_EXT_LOOPBACK,
+ &data[2]) != 0) {
test->flags |= ETH_TEST_FL_FAILED;
+ }
data[3] = be_test_ddr_dma(adapter);
if (data[3] != 0)
if (bp->cnic_eth_dev.drv_state & CNIC_DRV_STATE_REGD) {
bnx2x_set_iscsi_eth_mac_addr(bp, 1);
bp->cnic_flags |= BNX2X_CNIC_FLAG_MAC_SET;
+ bnx2x_init_sb(bp, bp->cnic_sb, bp->cnic_sb_mapping,
+ CNIC_SB_ID(bp));
}
mutex_unlock(&bp->cnic_mutex);
#endif
// check if any partner replys
if (best->is_individual) {
pr_warning("%s: Warning: No 802.3ad response from the link partner for any adapters in the bond\n",
- best->slave->dev->master->name);
+ best->slave ? best->slave->dev->master->name : "NULL");
}
best->is_active = 1;
static void gfar_clear_exact_match(struct net_device *dev);
static void gfar_set_mac_for_addr(struct net_device *dev, int num, u8 *addr);
static int gfar_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
-u16 gfar_select_queue(struct net_device *dev, struct sk_buff *skb);
MODULE_AUTHOR("Freescale Semiconductor, Inc");
MODULE_DESCRIPTION("Gianfar Ethernet Driver");
.ndo_set_multicast_list = gfar_set_multi,
.ndo_tx_timeout = gfar_timeout,
.ndo_do_ioctl = gfar_ioctl,
- .ndo_select_queue = gfar_select_queue,
.ndo_get_stats = gfar_get_stats,
.ndo_vlan_rx_register = gfar_vlan_rx_register,
.ndo_set_mac_address = eth_mac_addr,
return priv->vlgrp || priv->rx_csum_enable;
}
-u16 gfar_select_queue(struct net_device *dev, struct sk_buff *skb)
-{
- return skb_get_queue_mapping(skb);
-}
static void free_tx_pointers(struct gfar_private *priv)
{
int i = 0;
fcb = (struct rxfcb *)skb->data;
/* Remove the FCB from the skb */
- skb_set_queue_mapping(skb, fcb->rq);
/* Remove the padded bytes, if there are any */
- if (amount_pull)
+ if (amount_pull) {
+ skb_record_rx_queue(skb, fcb->rq);
skb_pull(skb, amount_pull);
+ }
if (priv->rx_csum_enable)
gfar_rx_checksum(skb, fcb);
/* Remove the FCS from the packet length */
skb_put(skb, pkt_len);
rx_queue->stats.rx_bytes += pkt_len;
-
+ skb_record_rx_queue(skb, rx_queue->qindex);
gfar_process_frame(dev, skb, amount_pull);
} else {
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
+#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/bitops.h>
/* copy out MAC address */
- for (z = 0; z < sizeof(dev->dev_addr); z++)
+ for (z = 0; z < ETH_ALEN; z++)
dev->dev_addr[z] = inb(dev->base_addr + MACADDRPROM + z);
/* print config */
hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg);
} else {
/* Set PCS register for forced link */
- reg |= E1000_PCS_LCTL_FSD | /* Force Speed */
- E1000_PCS_LCTL_FORCE_LINK | /* Force Link */
- E1000_PCS_LCTL_FLV_LINK_UP; /* Force link value up */
+ reg |= E1000_PCS_LCTL_FSD; /* Force Speed */
hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg);
}
phy_data |= I82580_CFG_ENABLE_DOWNSHIFT;
ret_val = phy->ops.write_reg(hw, I82580_CFG_REG, phy_data);
- if (ret_val)
- goto out;
-
- /* Set number of link attempts before downshift */
- ret_val = phy->ops.read_reg(hw, I82580_CTRL_REG, &phy_data);
- if (ret_val)
- goto out;
- phy_data &= ~I82580_CTRL_DOWNSHIFT_MASK;
- ret_val = phy->ops.write_reg(hw, I82580_CTRL_REG, phy_data);
out:
return ret_val;
/* dual port cards only support WoL on port A from now on
* unless it was enabled in the eeprom for port B
* so exclude FUNC_1 ports from having WoL enabled */
- if (rd32(E1000_STATUS) & E1000_STATUS_FUNC_1 &&
+ if ((rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) &&
!adapter->eeprom_wol) {
wol->supported = 0;
break;
hwm = min(((pba << 10) * 9 / 10),
((pba << 10) - 2 * adapter->max_frame_size));
- if (mac->type < e1000_82576) {
- fc->high_water = hwm & 0xFFF8; /* 8-byte granularity */
- fc->low_water = fc->high_water - 8;
- } else {
- fc->high_water = hwm & 0xFFF0; /* 16-byte granularity */
- fc->low_water = fc->high_water - 16;
- }
+ fc->high_water = hwm & 0xFFF0; /* 16-byte granularity */
+ fc->low_water = fc->high_water - 16;
fc->pause_time = 0xFFFF;
fc->send_xon = 1;
fc->current_mode = fc->requested_mode;
err = hw->mac.ops.reset_hw(hw);
if (err) {
dev_info(&pdev->dev,
- "PF still in reset state, assigning new address\n");
+ "PF still in reset state, assigning new address."
+ " Is the PF interface up?\n");
random_ether_addr(hw->mac.addr);
} else {
err = hw->mac.ops.read_mac_addr(hw);
pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
+ /*
+ * pci_restore_state clears dev->state_saved so call
+ * pci_save_state to restore it.
+ */
+ pci_save_state(pdev);
err = pci_enable_device_mem(pdev);
if (err) {
#include <linux/crc32.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
+#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/spinlock.h>
#include <linux/moduleparam.h>
/* if the ethernet address is not valid, force to 00:00:00:00:00:00 */
if (!is_valid_ether_addr(dev->perm_addr))
- memset(dev->dev_addr, 0, sizeof(dev->dev_addr));
+ memset(dev->dev_addr, 0, ETH_ALEN);
if (pcnet32_debug & NETIF_MSG_PROBE) {
printk(" %pM", dev->dev_addr);
EFX_LOG(efx, "create port\n");
+ if (phy_flash_cfg)
+ efx->phy_mode = PHY_MODE_SPECIAL;
+
/* Connect up MAC/PHY operations table */
rc = efx->type->probe_port(efx);
if (rc)
goto err;
- if (phy_flash_cfg)
- efx->phy_mode = PHY_MODE_SPECIAL;
-
/* Sanity check MAC address */
if (is_valid_ether_addr(efx->mac_address)) {
memcpy(efx->net_dev->dev_addr, efx->mac_address, ETH_ALEN);
static void falcon_remove_port(struct efx_nic *efx)
{
+ efx->phy_op->remove(efx);
efx_nic_free_buffer(efx, &efx->stats_buffer);
}
efx_writeo(efx, ®, FR_AB_XM_MGT_INT_MASK);
}
-/* Get status of XAUI link */
-static bool falcon_xaui_link_ok(struct efx_nic *efx)
+static bool falcon_xgxs_link_ok(struct efx_nic *efx)
{
efx_oword_t reg;
bool align_done, link_ok = false;
int sync_status;
- if (LOOPBACK_INTERNAL(efx))
- return true;
-
/* Read link status */
efx_reado(efx, ®, FR_AB_XX_CORE_STAT);
EFX_SET_OWORD_FIELD(reg, FRF_AB_XX_DISPERR, FFE_AB_XX_STAT_ALL_LANES);
efx_writeo(efx, ®, FR_AB_XX_CORE_STAT);
- /* If the link is up, then check the phy side of the xaui link */
- if (efx->link_state.up && link_ok)
- if (efx->mdio.mmds & (1 << MDIO_MMD_PHYXS))
- link_ok = efx_mdio_phyxgxs_lane_sync(efx);
-
return link_ok;
}
+static bool falcon_xmac_link_ok(struct efx_nic *efx)
+{
+ /*
+ * Check MAC's XGXS link status except when using XGMII loopback
+ * which bypasses the XGXS block.
+ * If possible, check PHY's XGXS link status except when using
+ * MAC loopback.
+ */
+ return (efx->loopback_mode == LOOPBACK_XGMII ||
+ falcon_xgxs_link_ok(efx)) &&
+ (!(efx->mdio.mmds & (1 << MDIO_MMD_PHYXS)) ||
+ LOOPBACK_INTERNAL(efx) ||
+ efx_mdio_phyxgxs_lane_sync(efx));
+}
+
void falcon_reconfigure_xmac_core(struct efx_nic *efx)
{
unsigned int max_frame_len;
/* Try to bring up the Falcon side of the Falcon-Phy XAUI link */
-static bool falcon_check_xaui_link_up(struct efx_nic *efx, int tries)
+static bool falcon_xmac_link_ok_retry(struct efx_nic *efx, int tries)
{
- bool mac_up = falcon_xaui_link_ok(efx);
+ bool mac_up = falcon_xmac_link_ok(efx);
if (LOOPBACK_MASK(efx) & LOOPBACKS_EXTERNAL(efx) & LOOPBACKS_WS ||
efx_phy_mode_disabled(efx->phy_mode))
falcon_reset_xaui(efx);
udelay(200);
- mac_up = falcon_xaui_link_ok(efx);
+ mac_up = falcon_xmac_link_ok(efx);
--tries;
}
static bool falcon_xmac_check_fault(struct efx_nic *efx)
{
- return !falcon_check_xaui_link_up(efx, 5);
+ return !falcon_xmac_link_ok_retry(efx, 5);
}
static int falcon_reconfigure_xmac(struct efx_nic *efx)
falcon_reconfigure_mac_wrapper(efx);
- efx->xmac_poll_required = !falcon_check_xaui_link_up(efx, 5);
+ efx->xmac_poll_required = !falcon_xmac_link_ok_retry(efx, 5);
falcon_mask_status_intr(efx, true);
return 0;
return;
falcon_mask_status_intr(efx, false);
- efx->xmac_poll_required = !falcon_check_xaui_link_up(efx, 1);
+ efx->xmac_poll_required = !falcon_xmac_link_ok_retry(efx, 1);
falcon_mask_status_intr(efx, true);
}
static int efx_mcdi_phy_probe(struct efx_nic *efx)
{
- struct efx_mcdi_phy_cfg *phy_cfg;
+ struct efx_mcdi_phy_cfg *phy_data;
+ u8 outbuf[MC_CMD_GET_LINK_OUT_LEN];
+ u32 caps;
int rc;
- /* TODO: Move phy_data initialisation to
- * phy_op->probe/remove, rather than init/fini */
- phy_cfg = kzalloc(sizeof(*phy_cfg), GFP_KERNEL);
- if (phy_cfg == NULL) {
- rc = -ENOMEM;
- goto fail_alloc;
- }
- rc = efx_mcdi_get_phy_cfg(efx, phy_cfg);
+ /* Initialise and populate phy_data */
+ phy_data = kzalloc(sizeof(*phy_data), GFP_KERNEL);
+ if (phy_data == NULL)
+ return -ENOMEM;
+
+ rc = efx_mcdi_get_phy_cfg(efx, phy_data);
if (rc != 0)
goto fail;
- efx->phy_type = phy_cfg->type;
+ /* Read initial link advertisement */
+ BUILD_BUG_ON(MC_CMD_GET_LINK_IN_LEN != 0);
+ rc = efx_mcdi_rpc(efx, MC_CMD_GET_LINK, NULL, 0,
+ outbuf, sizeof(outbuf), NULL);
+ if (rc)
+ goto fail;
+
+ /* Fill out nic state */
+ efx->phy_data = phy_data;
+ efx->phy_type = phy_data->type;
- efx->mdio_bus = phy_cfg->channel;
- efx->mdio.prtad = phy_cfg->port;
- efx->mdio.mmds = phy_cfg->mmd_mask & ~(1 << MC_CMD_MMD_CLAUSE22);
+ efx->mdio_bus = phy_data->channel;
+ efx->mdio.prtad = phy_data->port;
+ efx->mdio.mmds = phy_data->mmd_mask & ~(1 << MC_CMD_MMD_CLAUSE22);
efx->mdio.mode_support = 0;
- if (phy_cfg->mmd_mask & (1 << MC_CMD_MMD_CLAUSE22))
+ if (phy_data->mmd_mask & (1 << MC_CMD_MMD_CLAUSE22))
efx->mdio.mode_support |= MDIO_SUPPORTS_C22;
- if (phy_cfg->mmd_mask & ~(1 << MC_CMD_MMD_CLAUSE22))
+ if (phy_data->mmd_mask & ~(1 << MC_CMD_MMD_CLAUSE22))
efx->mdio.mode_support |= MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22;
+ caps = MCDI_DWORD(outbuf, GET_LINK_OUT_CAP);
+ if (caps & (1 << MC_CMD_PHY_CAP_AN_LBN))
+ efx->link_advertising =
+ mcdi_to_ethtool_cap(phy_data->media, caps);
+ else
+ phy_data->forced_cap = caps;
+
/* Assert that we can map efx -> mcdi loopback modes */
BUILD_BUG_ON(LOOPBACK_NONE != MC_CMD_LOOPBACK_NONE);
BUILD_BUG_ON(LOOPBACK_DATA != MC_CMD_LOOPBACK_DATA);
* but by convention we don't */
efx->loopback_modes &= ~(1 << LOOPBACK_NONE);
- kfree(phy_cfg);
-
- return 0;
-
-fail:
- kfree(phy_cfg);
-fail_alloc:
- return rc;
-}
-
-static int efx_mcdi_phy_init(struct efx_nic *efx)
-{
- struct efx_mcdi_phy_cfg *phy_data;
- u8 outbuf[MC_CMD_GET_LINK_OUT_LEN];
- u32 caps;
- int rc;
-
- phy_data = kzalloc(sizeof(*phy_data), GFP_KERNEL);
- if (phy_data == NULL)
- return -ENOMEM;
-
- rc = efx_mcdi_get_phy_cfg(efx, phy_data);
- if (rc != 0)
- goto fail;
-
- efx->phy_data = phy_data;
-
- BUILD_BUG_ON(MC_CMD_GET_LINK_IN_LEN != 0);
- rc = efx_mcdi_rpc(efx, MC_CMD_GET_LINK, NULL, 0,
- outbuf, sizeof(outbuf), NULL);
- if (rc)
- goto fail;
-
- caps = MCDI_DWORD(outbuf, GET_LINK_OUT_CAP);
- if (caps & (1 << MC_CMD_PHY_CAP_AN_LBN))
- efx->link_advertising =
- mcdi_to_ethtool_cap(phy_data->media, caps);
- else
- phy_data->forced_cap = caps;
-
return 0;
fail:
return !efx_link_state_equal(&efx->link_state, &old_state);
}
-static void efx_mcdi_phy_fini(struct efx_nic *efx)
+static void efx_mcdi_phy_remove(struct efx_nic *efx)
{
struct efx_mcdi_phy_data *phy_data = efx->phy_data;
struct efx_phy_operations efx_mcdi_phy_ops = {
.probe = efx_mcdi_phy_probe,
- .init = efx_mcdi_phy_init,
+ .init = efx_port_dummy_op_int,
.reconfigure = efx_mcdi_phy_reconfigure,
.poll = efx_mcdi_phy_poll,
- .fini = efx_mcdi_phy_fini,
+ .fini = efx_port_dummy_op_void,
+ .remove = efx_mcdi_phy_remove,
.get_settings = efx_mcdi_phy_get_settings,
.set_settings = efx_mcdi_phy_set_settings,
.run_tests = NULL,
int (*probe) (struct efx_nic *efx);
int (*init) (struct efx_nic *efx);
void (*fini) (struct efx_nic *efx);
+ void (*remove) (struct efx_nic *efx);
int (*reconfigure) (struct efx_nic *efx);
bool (*poll) (struct efx_nic *efx);
void (*get_settings) (struct efx_nic *efx,
EFX_SET_OWORD_FIELD(temp, FRF_AZ_TX_SOFT_EVT_EN, 1);
/* Prefetch threshold 2 => fetch when descriptor cache half empty */
EFX_SET_OWORD_FIELD(temp, FRF_AZ_TX_PREF_THRESHOLD, 2);
+ /* Disable hardware watchdog which can misfire */
+ EFX_SET_OWORD_FIELD(temp, FRF_AZ_TX_PREF_WD_TMR, 0x3fffff);
/* Squash TX of packets of 16 bytes or less */
if (efx_nic_rev(efx) >= EFX_REV_FALCON_B0)
EFX_SET_OWORD_FIELD(temp, FRF_BZ_TX_FLUSH_MIN_LEN_EN, 1);
#define PCS_FW_HEARTBEAT_REG 0xd7ee
#define PCS_FW_HEARTB_LBN 0
#define PCS_FW_HEARTB_WIDTH 8
+#define PCS_FW_PRODUCT_CODE_1 0xd7f0
+#define PCS_FW_VERSION_1 0xd7f3
+#define PCS_FW_BUILD_1 0xd7f6
#define PCS_UC8051_STATUS_REG 0xd7fd
#define PCS_UC_STATUS_LBN 0
#define PCS_UC_STATUS_WIDTH 8
struct qt202x_phy_data {
enum efx_phy_mode phy_mode;
+ bool bug17190_in_bad_state;
+ unsigned long bug17190_timer;
+ u32 firmware_ver;
};
#define QT2022C2_MAX_RESET_TIME 500
#define QT2022C2_RESET_WAIT 10
-static int qt2025c_wait_reset(struct efx_nic *efx)
+#define QT2025C_MAX_HEARTB_TIME (5 * HZ)
+#define QT2025C_HEARTB_WAIT 100
+#define QT2025C_MAX_FWSTART_TIME (25 * HZ / 10)
+#define QT2025C_FWSTART_WAIT 100
+
+#define BUG17190_INTERVAL (2 * HZ)
+
+static int qt2025c_wait_heartbeat(struct efx_nic *efx)
{
- unsigned long timeout = jiffies + 10 * HZ;
+ unsigned long timeout = jiffies + QT2025C_MAX_HEARTB_TIME;
int reg, old_counter = 0;
/* Wait for firmware heartbeat to start */
old_counter = counter;
else if (counter != old_counter)
break;
- if (time_after(jiffies, timeout))
+ if (time_after(jiffies, timeout)) {
+ /* Some cables have EEPROMs that conflict with the
+ * PHY's on-board EEPROM so it cannot load firmware */
+ EFX_ERR(efx, "If an SFP+ direct attach cable is"
+ " connected, please check that it complies"
+ " with the SFP+ specification\n");
return -ETIMEDOUT;
- msleep(10);
+ }
+ msleep(QT2025C_HEARTB_WAIT);
}
+ return 0;
+}
+
+static int qt2025c_wait_fw_status_good(struct efx_nic *efx)
+{
+ unsigned long timeout = jiffies + QT2025C_MAX_FWSTART_TIME;
+ int reg;
+
/* Wait for firmware status to look good */
for (;;) {
reg = efx_mdio_read(efx, MDIO_MMD_PCS, PCS_UC8051_STATUS_REG);
break;
if (time_after(jiffies, timeout))
return -ETIMEDOUT;
+ msleep(QT2025C_FWSTART_WAIT);
+ }
+
+ return 0;
+}
+
+static void qt2025c_restart_firmware(struct efx_nic *efx)
+{
+ /* Restart microcontroller execution of firmware from RAM */
+ efx_mdio_write(efx, 3, 0xe854, 0x00c0);
+ efx_mdio_write(efx, 3, 0xe854, 0x0040);
+ msleep(50);
+}
+
+static int qt2025c_wait_reset(struct efx_nic *efx)
+{
+ int rc;
+
+ rc = qt2025c_wait_heartbeat(efx);
+ if (rc != 0)
+ return rc;
+
+ rc = qt2025c_wait_fw_status_good(efx);
+ if (rc == -ETIMEDOUT) {
+ /* Bug 17689: occasionally heartbeat starts but firmware status
+ * code never progresses beyond 0x00. Try again, once, after
+ * restarting execution of the firmware image. */
+ EFX_LOG(efx, "bashing QT2025C microcontroller\n");
+ qt2025c_restart_firmware(efx);
+ rc = qt2025c_wait_heartbeat(efx);
+ if (rc != 0)
+ return rc;
+ rc = qt2025c_wait_fw_status_good(efx);
+ }
+
+ return rc;
+}
+
+static void qt2025c_firmware_id(struct efx_nic *efx)
+{
+ struct qt202x_phy_data *phy_data = efx->phy_data;
+ u8 firmware_id[9];
+ size_t i;
+
+ for (i = 0; i < sizeof(firmware_id); i++)
+ firmware_id[i] = efx_mdio_read(efx, MDIO_MMD_PCS,
+ PCS_FW_PRODUCT_CODE_1 + i);
+ EFX_INFO(efx, "QT2025C firmware %xr%d v%d.%d.%d.%d [20%02d-%02d-%02d]\n",
+ (firmware_id[0] << 8) | firmware_id[1], firmware_id[2],
+ firmware_id[3] >> 4, firmware_id[3] & 0xf,
+ firmware_id[4], firmware_id[5],
+ firmware_id[6], firmware_id[7], firmware_id[8]);
+ phy_data->firmware_ver = ((firmware_id[3] & 0xf0) << 20) |
+ ((firmware_id[3] & 0x0f) << 16) |
+ (firmware_id[4] << 8) | firmware_id[5];
+}
+
+static void qt2025c_bug17190_workaround(struct efx_nic *efx)
+{
+ struct qt202x_phy_data *phy_data = efx->phy_data;
+
+ /* The PHY can get stuck in a state where it reports PHY_XS and PMA/PMD
+ * layers up, but PCS down (no block_lock). If we notice this state
+ * persisting for a couple of seconds, we switch PMA/PMD loopback
+ * briefly on and then off again, which is normally sufficient to
+ * recover it.
+ */
+ if (efx->link_state.up ||
+ !efx_mdio_links_ok(efx, MDIO_DEVS_PMAPMD | MDIO_DEVS_PHYXS)) {
+ phy_data->bug17190_in_bad_state = false;
+ return;
+ }
+
+ if (!phy_data->bug17190_in_bad_state) {
+ phy_data->bug17190_in_bad_state = true;
+ phy_data->bug17190_timer = jiffies + BUG17190_INTERVAL;
+ return;
+ }
+
+ if (time_after_eq(jiffies, phy_data->bug17190_timer)) {
+ EFX_LOG(efx, "bashing QT2025C PMA/PMD\n");
+ efx_mdio_set_flag(efx, MDIO_MMD_PMAPMD, MDIO_CTRL1,
+ MDIO_PMA_CTRL1_LOOPBACK, true);
msleep(100);
+ efx_mdio_set_flag(efx, MDIO_MMD_PMAPMD, MDIO_CTRL1,
+ MDIO_PMA_CTRL1_LOOPBACK, false);
+ phy_data->bug17190_timer = jiffies + BUG17190_INTERVAL;
+ }
+}
+
+static int qt2025c_select_phy_mode(struct efx_nic *efx)
+{
+ struct qt202x_phy_data *phy_data = efx->phy_data;
+ struct falcon_board *board = falcon_board(efx);
+ int reg, rc, i;
+ uint16_t phy_op_mode;
+
+ /* Only 2.0.1.0+ PHY firmware supports the more optimal SFP+
+ * Self-Configure mode. Don't attempt any switching if we encounter
+ * older firmware. */
+ if (phy_data->firmware_ver < 0x02000100)
+ return 0;
+
+ /* In general we will get optimal behaviour in "SFP+ Self-Configure"
+ * mode; however, that powers down most of the PHY when no module is
+ * present, so we must use a different mode (any fixed mode will do)
+ * to be sure that loopbacks will work. */
+ phy_op_mode = (efx->loopback_mode == LOOPBACK_NONE) ? 0x0038 : 0x0020;
+
+ /* Only change mode if really necessary */
+ reg = efx_mdio_read(efx, 1, 0xc319);
+ if ((reg & 0x0038) == phy_op_mode)
+ return 0;
+ EFX_LOG(efx, "Switching PHY to mode 0x%04x\n", phy_op_mode);
+
+ /* This sequence replicates the register writes configured in the boot
+ * EEPROM (including the differences between board revisions), except
+ * that the operating mode is changed, and the PHY is prevented from
+ * unnecessarily reloading the main firmware image again. */
+ efx_mdio_write(efx, 1, 0xc300, 0x0000);
+ /* (Note: this portion of the boot EEPROM sequence, which bit-bashes 9
+ * STOPs onto the firmware/module I2C bus to reset it, varies across
+ * board revisions, as the bus is connected to different GPIO/LED
+ * outputs on the PHY.) */
+ if (board->major == 0 && board->minor < 2) {
+ efx_mdio_write(efx, 1, 0xc303, 0x4498);
+ for (i = 0; i < 9; i++) {
+ efx_mdio_write(efx, 1, 0xc303, 0x4488);
+ efx_mdio_write(efx, 1, 0xc303, 0x4480);
+ efx_mdio_write(efx, 1, 0xc303, 0x4490);
+ efx_mdio_write(efx, 1, 0xc303, 0x4498);
+ }
+ } else {
+ efx_mdio_write(efx, 1, 0xc303, 0x0920);
+ efx_mdio_write(efx, 1, 0xd008, 0x0004);
+ for (i = 0; i < 9; i++) {
+ efx_mdio_write(efx, 1, 0xc303, 0x0900);
+ efx_mdio_write(efx, 1, 0xd008, 0x0005);
+ efx_mdio_write(efx, 1, 0xc303, 0x0920);
+ efx_mdio_write(efx, 1, 0xd008, 0x0004);
+ }
+ efx_mdio_write(efx, 1, 0xc303, 0x4900);
+ }
+ efx_mdio_write(efx, 1, 0xc303, 0x4900);
+ efx_mdio_write(efx, 1, 0xc302, 0x0004);
+ efx_mdio_write(efx, 1, 0xc316, 0x0013);
+ efx_mdio_write(efx, 1, 0xc318, 0x0054);
+ efx_mdio_write(efx, 1, 0xc319, phy_op_mode);
+ efx_mdio_write(efx, 1, 0xc31a, 0x0098);
+ efx_mdio_write(efx, 3, 0x0026, 0x0e00);
+ efx_mdio_write(efx, 3, 0x0027, 0x0013);
+ efx_mdio_write(efx, 3, 0x0028, 0xa528);
+ efx_mdio_write(efx, 1, 0xd006, 0x000a);
+ efx_mdio_write(efx, 1, 0xd007, 0x0009);
+ efx_mdio_write(efx, 1, 0xd008, 0x0004);
+ /* This additional write is not present in the boot EEPROM. It
+ * prevents the PHY's internal boot ROM doing another pointless (and
+ * slow) reload of the firmware image (the microcontroller's code
+ * memory is not affected by the microcontroller reset). */
+ efx_mdio_write(efx, 1, 0xc317, 0x00ff);
+ efx_mdio_write(efx, 1, 0xc300, 0x0002);
+ msleep(20);
+
+ /* Restart microcontroller execution of firmware from RAM */
+ qt2025c_restart_firmware(efx);
+
+ /* Wait for the microcontroller to be ready again */
+ rc = qt2025c_wait_reset(efx);
+ if (rc < 0) {
+ EFX_ERR(efx, "PHY microcontroller reset during mode switch "
+ "timed out\n");
+ return rc;
}
return 0;
static int qt202x_phy_probe(struct efx_nic *efx)
{
+ struct qt202x_phy_data *phy_data;
+
+ phy_data = kzalloc(sizeof(struct qt202x_phy_data), GFP_KERNEL);
+ if (!phy_data)
+ return -ENOMEM;
+ efx->phy_data = phy_data;
+ phy_data->phy_mode = efx->phy_mode;
+ phy_data->bug17190_in_bad_state = false;
+ phy_data->bug17190_timer = 0;
+
efx->mdio.mmds = QT202X_REQUIRED_DEVS;
efx->mdio.mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22;
efx->loopback_modes = QT202X_LOOPBACKS | FALCON_XMAC_LOOPBACKS;
static int qt202x_phy_init(struct efx_nic *efx)
{
- struct qt202x_phy_data *phy_data;
u32 devid;
int rc;
return rc;
}
- phy_data = kzalloc(sizeof(struct qt202x_phy_data), GFP_KERNEL);
- if (!phy_data)
- return -ENOMEM;
- efx->phy_data = phy_data;
-
devid = efx_mdio_read_id(efx, MDIO_MMD_PHYXS);
EFX_INFO(efx, "PHY ID reg %x (OUI %06x model %02x revision %x)\n",
devid, efx_mdio_id_oui(devid), efx_mdio_id_model(devid),
efx_mdio_id_rev(devid));
- phy_data->phy_mode = efx->phy_mode;
+ if (efx->phy_type == PHY_TYPE_QT2025C)
+ qt2025c_firmware_id(efx);
+
return 0;
}
efx->link_state.fd = true;
efx->link_state.fc = efx->wanted_fc;
+ if (efx->phy_type == PHY_TYPE_QT2025C)
+ qt2025c_bug17190_workaround(efx);
+
return efx->link_state.up != was_up;
}
struct qt202x_phy_data *phy_data = efx->phy_data;
if (efx->phy_type == PHY_TYPE_QT2025C) {
+ int rc = qt2025c_select_phy_mode(efx);
+ if (rc)
+ return rc;
+
/* There are several different register bits which can
* disable TX (and save power) on direct-attach cables
* or optical transceivers, varying somewhat between
mdio45_ethtool_gset(&efx->mdio, ecmd);
}
-static void qt202x_phy_fini(struct efx_nic *efx)
+static void qt202x_phy_remove(struct efx_nic *efx)
{
/* Free the context block */
kfree(efx->phy_data);
.init = qt202x_phy_init,
.reconfigure = qt202x_phy_reconfigure,
.poll = qt202x_phy_poll,
- .fini = qt202x_phy_fini,
+ .fini = efx_port_dummy_op_void,
+ .remove = qt202x_phy_remove,
.get_settings = qt202x_phy_get_settings,
.set_settings = efx_mdio_set_settings,
};
void siena_remove_port(struct efx_nic *efx)
{
+ efx->phy_op->remove(efx);
efx_nic_free_buffer(efx, &efx->stats_buffer);
}
int rc;
rtnl_lock();
- efx_mdio_set_flag(efx, MDIO_MMD_PMAPMD, MDIO_PMA_10GBT_TXPWR,
- MDIO_PMA_10GBT_TXPWR_SHORT,
- count != 0 && *buf != '0');
- rc = efx_reconfigure_port(efx);
+ if (efx->state != STATE_RUNNING) {
+ rc = -EBUSY;
+ } else {
+ efx_mdio_set_flag(efx, MDIO_MMD_PMAPMD, MDIO_PMA_10GBT_TXPWR,
+ MDIO_PMA_10GBT_TXPWR_SHORT,
+ count != 0 && *buf != '0');
+ rc = efx_reconfigure_port(efx);
+ }
rtnl_unlock();
return rc < 0 ? rc : (ssize_t)count;
return 0;
}
-static int sfx7101_phy_probe(struct efx_nic *efx)
+static int tenxpress_phy_probe(struct efx_nic *efx)
{
- efx->mdio.mmds = TENXPRESS_REQUIRED_DEVS;
- efx->mdio.mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22;
- efx->loopback_modes = SFX7101_LOOPBACKS | FALCON_XMAC_LOOPBACKS;
- return 0;
-}
+ struct tenxpress_phy_data *phy_data;
+ int rc;
+
+ /* Allocate phy private storage */
+ phy_data = kzalloc(sizeof(*phy_data), GFP_KERNEL);
+ if (!phy_data)
+ return -ENOMEM;
+ efx->phy_data = phy_data;
+ phy_data->phy_mode = efx->phy_mode;
+
+ /* Create any special files */
+ if (efx->phy_type == PHY_TYPE_SFT9001B) {
+ rc = device_create_file(&efx->pci_dev->dev,
+ &dev_attr_phy_short_reach);
+ if (rc)
+ goto fail;
+ }
+
+ if (efx->phy_type == PHY_TYPE_SFX7101) {
+ efx->mdio.mmds = TENXPRESS_REQUIRED_DEVS;
+ efx->mdio.mode_support = MDIO_SUPPORTS_C45;
+
+ efx->loopback_modes = SFX7101_LOOPBACKS | FALCON_XMAC_LOOPBACKS;
+
+ efx->link_advertising = (ADVERTISED_TP | ADVERTISED_Autoneg |
+ ADVERTISED_10000baseT_Full);
+ } else {
+ efx->mdio.mmds = TENXPRESS_REQUIRED_DEVS;
+ efx->mdio.mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22;
+
+ efx->loopback_modes = (SFT9001_LOOPBACKS |
+ FALCON_XMAC_LOOPBACKS |
+ FALCON_GMAC_LOOPBACKS);
+
+ efx->link_advertising = (ADVERTISED_TP | ADVERTISED_Autoneg |
+ ADVERTISED_10000baseT_Full |
+ ADVERTISED_1000baseT_Full |
+ ADVERTISED_100baseT_Full);
+ }
-static int sft9001_phy_probe(struct efx_nic *efx)
-{
- efx->mdio.mmds = TENXPRESS_REQUIRED_DEVS;
- efx->mdio.mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22;
- efx->loopback_modes = (SFT9001_LOOPBACKS | FALCON_XMAC_LOOPBACKS |
- FALCON_GMAC_LOOPBACKS);
return 0;
+
+fail:
+ kfree(efx->phy_data);
+ efx->phy_data = NULL;
+ return rc;
}
static int tenxpress_phy_init(struct efx_nic *efx)
{
- struct tenxpress_phy_data *phy_data;
- int rc = 0;
+ int rc;
falcon_board(efx)->type->init_phy(efx);
- phy_data = kzalloc(sizeof(*phy_data), GFP_KERNEL);
- if (!phy_data)
- return -ENOMEM;
- efx->phy_data = phy_data;
- phy_data->phy_mode = efx->phy_mode;
-
if (!(efx->phy_mode & PHY_MODE_SPECIAL)) {
if (efx->phy_type == PHY_TYPE_SFT9001A) {
int reg;
rc = efx_mdio_wait_reset_mmds(efx, TENXPRESS_REQUIRED_DEVS);
if (rc < 0)
- goto fail;
+ return rc;
rc = efx_mdio_check_mmds(efx, TENXPRESS_REQUIRED_DEVS, 0);
if (rc < 0)
- goto fail;
+ return rc;
}
rc = tenxpress_init(efx);
if (rc < 0)
- goto fail;
+ return rc;
- /* Initialise advertising flags */
- efx->link_advertising = (ADVERTISED_TP | ADVERTISED_Autoneg |
- ADVERTISED_10000baseT_Full);
- if (efx->phy_type != PHY_TYPE_SFX7101)
- efx->link_advertising |= (ADVERTISED_1000baseT_Full |
- ADVERTISED_100baseT_Full);
+ /* Reinitialise flow control settings */
efx_link_set_wanted_fc(efx, efx->wanted_fc);
efx_mdio_an_reconfigure(efx);
- if (efx->phy_type == PHY_TYPE_SFT9001B) {
- rc = device_create_file(&efx->pci_dev->dev,
- &dev_attr_phy_short_reach);
- if (rc)
- goto fail;
- }
-
schedule_timeout_uninterruptible(HZ / 5); /* 200ms */
/* Let XGXS and SerDes out of reset */
falcon_reset_xaui(efx);
return 0;
-
- fail:
- kfree(efx->phy_data);
- efx->phy_data = NULL;
- return rc;
}
/* Perform a "special software reset" on the PHY. The caller is
return !efx_link_state_equal(&efx->link_state, &old_state);
}
-static void tenxpress_phy_fini(struct efx_nic *efx)
+static void sfx7101_phy_fini(struct efx_nic *efx)
{
int reg;
+ /* Power down the LNPGA */
+ reg = (1 << PMA_PMD_LNPGA_POWERDOWN_LBN);
+ efx_mdio_write(efx, MDIO_MMD_PMAPMD, PMA_PMD_XCONTROL_REG, reg);
+
+ /* Waiting here ensures that the board fini, which can turn
+ * off the power to the PHY, won't get run until the LNPGA
+ * powerdown has been given long enough to complete. */
+ schedule_timeout_uninterruptible(LNPGA_PDOWN_WAIT); /* 200 ms */
+}
+
+static void tenxpress_phy_remove(struct efx_nic *efx)
+{
if (efx->phy_type == PHY_TYPE_SFT9001B)
device_remove_file(&efx->pci_dev->dev,
&dev_attr_phy_short_reach);
- if (efx->phy_type == PHY_TYPE_SFX7101) {
- /* Power down the LNPGA */
- reg = (1 << PMA_PMD_LNPGA_POWERDOWN_LBN);
- efx_mdio_write(efx, MDIO_MMD_PMAPMD, PMA_PMD_XCONTROL_REG, reg);
-
- /* Waiting here ensures that the board fini, which can turn
- * off the power to the PHY, won't get run until the LNPGA
- * powerdown has been given long enough to complete. */
- schedule_timeout_uninterruptible(LNPGA_PDOWN_WAIT); /* 200 ms */
- }
-
kfree(efx->phy_data);
efx->phy_data = NULL;
}
}
struct efx_phy_operations falcon_sfx7101_phy_ops = {
- .probe = sfx7101_phy_probe,
+ .probe = tenxpress_phy_probe,
.init = tenxpress_phy_init,
.reconfigure = tenxpress_phy_reconfigure,
.poll = tenxpress_phy_poll,
- .fini = tenxpress_phy_fini,
+ .fini = sfx7101_phy_fini,
+ .remove = tenxpress_phy_remove,
.get_settings = tenxpress_get_settings,
.set_settings = tenxpress_set_settings,
.set_npage_adv = sfx7101_set_npage_adv,
};
struct efx_phy_operations falcon_sft9001_phy_ops = {
- .probe = sft9001_phy_probe,
+ .probe = tenxpress_phy_probe,
.init = tenxpress_phy_init,
.reconfigure = tenxpress_phy_reconfigure,
.poll = tenxpress_phy_poll,
- .fini = tenxpress_phy_fini,
+ .fini = efx_port_dummy_op_void,
+ .remove = tenxpress_phy_remove,
.get_settings = tenxpress_get_settings,
.set_settings = tenxpress_set_settings,
.set_npage_adv = sft9001_set_npage_adv,
EFX_TXQ_MASK];
efx_tsoh_free(tx_queue, buffer);
EFX_BUG_ON_PARANOID(buffer->skb);
- buffer->len = 0;
- buffer->continuation = true;
if (buffer->unmap_len) {
unmap_addr = (buffer->dma_addr + buffer->len -
buffer->unmap_len);
PCI_DMA_TODEVICE);
buffer->unmap_len = 0;
}
+ buffer->len = 0;
+ buffer->continuation = true;
}
}
if (sk->sk_sleep && waitqueue_active(sk->sk_sleep))
wake_up_interruptible_sync(sk->sk_sleep);
- tun = container_of(sk, struct tun_sock, sk)->tun;
+ tun = tun_sk(sk)->tun;
kill_fasync(&tun->fasync, SIGIO, POLL_OUT);
}
static void tun_sock_destruct(struct sock *sk)
{
- free_netdev(container_of(sk, struct tun_sock, sk)->tun->dev);
+ free_netdev(tun_sk(sk)->tun->dev);
}
static struct proto tun_proto = {
sk->sk_write_space = tun_sock_write_space;
sk->sk_sndbuf = INT_MAX;
- container_of(sk, struct tun_sock, sk)->tun = tun;
+ tun_sk(sk)->tun = tun;
security_tun_dev_post_create(sk);
static void ugeth_quiesce(struct ucc_geth_private *ugeth)
{
- /* Wait for and prevent any further xmits. */
+ /* Prevent any further xmits, plus detach the device. */
+ netif_device_detach(ugeth->ndev);
+
+ /* Wait for any current xmits to finish. */
netif_tx_disable(ugeth->ndev);
/* Disable the interrupt to avoid NAPI rescheduling. */
{
napi_enable(&ugeth->napi);
enable_irq(ugeth->ug_info->uf_info.irq);
- netif_tx_wake_all_queues(ugeth->ndev);
+ netif_device_attach(ugeth->ndev);
}
/* Called every time the controller might need to be made
ugeth->oldspeed = phydev->speed;
}
- /*
- * To change the MAC configuration we need to disable the
- * controller. To do so, we have to either grab ugeth->lock,
- * which is a bad idea since 'graceful stop' commands might
- * take quite a while, or we can quiesce driver's activity.
- */
- ugeth_quiesce(ugeth);
- ugeth_disable(ugeth, COMM_DIR_RX_AND_TX);
-
- out_be32(&ug_regs->maccfg2, tempval);
- out_be32(&uf_regs->upsmr, upsmr);
-
- ugeth_enable(ugeth, COMM_DIR_RX_AND_TX);
- ugeth_activate(ugeth);
-
if (!ugeth->oldlink) {
new_state = 1;
ugeth->oldlink = 1;
}
+
+ if (new_state) {
+ /*
+ * To change the MAC configuration we need to disable
+ * the controller. To do so, we have to either grab
+ * ugeth->lock, which is a bad idea since 'graceful
+ * stop' commands might take quite a while, or we can
+ * quiesce driver's activity.
+ */
+ ugeth_quiesce(ugeth);
+ ugeth_disable(ugeth, COMM_DIR_RX_AND_TX);
+
+ out_be32(&ug_regs->maccfg2, tempval);
+ out_be32(&uf_regs->upsmr, upsmr);
+
+ ugeth_enable(ugeth, COMM_DIR_RX_AND_TX);
+ ugeth_activate(ugeth);
+ }
} else if (ugeth->oldlink) {
new_state = 1;
ugeth->oldlink = 0;
/* Handle the transmitted buffer and release */
/* the BD to be used with the current frame */
- if ((bd == ugeth->txBd[txQ]) && (netif_queue_stopped(dev) == 0))
+ if (bd == ugeth->txBd[txQ]) /* queue empty? */
break;
dev->stats.tx_packets++;
#include <linux/ethtool.h>
#include <linux/crc32.h>
#include <linux/bitops.h>
+#include <linux/workqueue.h>
#include <asm/processor.h> /* Processor type for cache alignment. */
#include <asm/io.h>
#include <asm/irq.h>
struct net_device *dev;
struct napi_struct napi;
spinlock_t lock;
+ struct work_struct reset_task;
/* Frequently used values: keep some adjacent for cache effect. */
u32 quirks;
static int mdio_read(struct net_device *dev, int phy_id, int location);
static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
static int rhine_open(struct net_device *dev);
+static void rhine_reset_task(struct work_struct *work);
static void rhine_tx_timeout(struct net_device *dev);
static netdev_tx_t rhine_start_tx(struct sk_buff *skb,
struct net_device *dev);
dev->irq = pdev->irq;
spin_lock_init(&rp->lock);
+ INIT_WORK(&rp->reset_task, rhine_reset_task);
+
rp->mii_if.dev = dev;
rp->mii_if.mdio_read = mdio_read;
rp->mii_if.mdio_write = mdio_write;
return 0;
}
-static void rhine_tx_timeout(struct net_device *dev)
+static void rhine_reset_task(struct work_struct *work)
{
- struct rhine_private *rp = netdev_priv(dev);
- void __iomem *ioaddr = rp->base;
-
- printk(KERN_WARNING "%s: Transmit timed out, status %4.4x, PHY status "
- "%4.4x, resetting...\n",
- dev->name, ioread16(ioaddr + IntrStatus),
- mdio_read(dev, rp->mii_if.phy_id, MII_BMSR));
+ struct rhine_private *rp = container_of(work, struct rhine_private,
+ reset_task);
+ struct net_device *dev = rp->dev;
/* protect against concurrent rx interrupts */
disable_irq(rp->pdev->irq);
napi_disable(&rp->napi);
- spin_lock(&rp->lock);
+ spin_lock_bh(&rp->lock);
/* clear all descriptors */
free_tbufs(dev);
rhine_chip_reset(dev);
init_registers(dev);
- spin_unlock(&rp->lock);
+ spin_unlock_bh(&rp->lock);
enable_irq(rp->pdev->irq);
dev->trans_start = jiffies;
netif_wake_queue(dev);
}
+static void rhine_tx_timeout(struct net_device *dev)
+{
+ struct rhine_private *rp = netdev_priv(dev);
+ void __iomem *ioaddr = rp->base;
+
+ printk(KERN_WARNING "%s: Transmit timed out, status %4.4x, PHY status "
+ "%4.4x, resetting...\n",
+ dev->name, ioread16(ioaddr + IntrStatus),
+ mdio_read(dev, rp->mii_if.phy_id, MII_BMSR));
+
+ schedule_work(&rp->reset_task);
+}
+
static netdev_tx_t rhine_start_tx(struct sk_buff *skb,
struct net_device *dev)
{
struct rhine_private *rp = netdev_priv(dev);
void __iomem *ioaddr = rp->base;
- spin_lock_irq(&rp->lock);
-
- netif_stop_queue(dev);
napi_disable(&rp->napi);
+ cancel_work_sync(&rp->reset_task);
+ netif_stop_queue(dev);
+
+ spin_lock_irq(&rp->lock);
if (debug > 1)
printk(KERN_DEBUG "%s: Shutting down ethercard, "
goto _exit0;
}
- if (!pci_set_dma_mask(pdev, 0xffffffffffffffffULL)) {
+ if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
vxge_debug_ll_config(VXGE_TRACE,
"%s : using 64bit DMA", __func__);
high_dma = 1;
if (pci_set_consistent_dma_mask(pdev,
- 0xffffffffffffffffULL)) {
+ DMA_BIT_MASK(64))) {
vxge_debug_init(VXGE_ERR,
"%s : unable to obtain 64bit DMA for "
"consistent allocations", __func__);
ret = -ENOMEM;
goto _exit1;
}
- } else if (!pci_set_dma_mask(pdev, 0xffffffffUL)) {
+ } else if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
vxge_debug_ll_config(VXGE_TRACE,
"%s : using 32bit DMA", __func__);
} else {
rxs->noise = sc->ah->ah_noise_floor;
rxs->signal = rxs->noise + rs.rs_rssi;
- /* An rssi of 35 indicates you should be able use
- * 54 Mbps reliably. A more elaborate scheme can be used
- * here but it requires a map of SNR/throughput for each
- * possible mode used */
- rxs->qual = rs.rs_rssi * 100 / 35;
-
- /* rssi can be more than 35 though, anything above that
- * should be considered at 100% */
- if (rxs->qual > 100)
- rxs->qual = 100;
-
rxs->antenna = rs.rs_antenna;
rxs->rate_idx = ath5k_hw_to_driver_rix(sc, rs.rs_rate);
rxs->flag |= ath5k_rx_decrypted(sc, ds, skb, &rs);
*/
ath5k_stop_locked(sc);
+ /* Set PHY calibration interval */
+ ah->ah_cal_intval = ath5k_calinterval;
+
/*
* The basic interface to setting the hardware in a good
* state is ``reset''. On return the hardware is known to
/* Set ack to be sent at low bit-rates */
ath5k_hw_set_ack_bitrate_high(ah, false);
-
- /* Set PHY calibration inteval */
- ah->ah_cal_intval = ath5k_calinterval;
-
ret = 0;
done:
mmiowb();
wait = wait_time;
while (ath9k_hw_numtxpending(ah, q)) {
if ((--wait) == 0) {
- ath_print(common, ATH_DBG_QUEUE,
+ ath_print(common, ATH_DBG_FATAL,
"Failed to stop TX DMA in 100 "
"msec after killing last frame\n");
break;
#define ATH9K_TXERR_XTXOP 0x08
#define ATH9K_TXERR_TIMER_EXPIRED 0x10
#define ATH9K_TX_ACKED 0x20
+#define ATH9K_TXERR_MASK \
+ (ATH9K_TXERR_XRETRY | ATH9K_TXERR_FILT | ATH9K_TXERR_FIFO | \
+ ATH9K_TXERR_XTXOP | ATH9K_TXERR_TIMER_EXPIRED)
#define ATH9K_TX_BA 0x01
#define ATH9K_TX_PWRMGMT 0x02
struct ieee80211_hw *hw = sc->hw;
int r;
+ /* Stop ANI */
+ del_timer_sync(&common->ani.timer);
+
ath9k_hw_set_interrupts(ah, 0);
ath_drain_all_txq(sc, retry_tx);
ath_stoprecv(sc);
}
}
+ /* Start ANI */
+ ath_start_ani(common);
+
return r;
}
return; /* another wiphy still in use */
}
+ /* Ensure HW is awake when we try to shut it down. */
+ ath9k_ps_wakeup(sc);
+
if (ah->btcoex_hw.enabled) {
ath9k_hw_btcoex_disable(ah);
if (ah->btcoex_hw.scheme == ATH_BTCOEX_CFG_3WIRE)
/* disable HAL and put h/w to sleep */
ath9k_hw_disable(ah);
ath9k_hw_configpcipowersave(ah, 1, 1);
+ ath9k_ps_restore(sc);
+
+ /* Finally, put the chip in FULL SLEEP mode */
ath9k_setpower(sc, ATH9K_PM_FULL_SLEEP);
sc->sc_flags |= SC_OP_INVALID;
if ((sc->sc_ah->opmode == NL80211_IFTYPE_AP) ||
(sc->sc_ah->opmode == NL80211_IFTYPE_ADHOC) ||
(sc->sc_ah->opmode == NL80211_IFTYPE_MESH_POINT)) {
+ ath9k_ps_wakeup(sc);
ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq);
ath_beacon_return(sc, avp);
+ ath9k_ps_restore(sc);
}
sc->sc_flags &= ~SC_OP_BEACONS;
case IEEE80211_AMPDU_RX_STOP:
break;
case IEEE80211_AMPDU_TX_START:
+ ath9k_ps_wakeup(sc);
ath_tx_aggr_start(sc, sta, tid, ssn);
ieee80211_start_tx_ba_cb_irqsafe(vif, sta->addr, tid);
+ ath9k_ps_restore(sc);
break;
case IEEE80211_AMPDU_TX_STOP:
+ ath9k_ps_wakeup(sc);
ath_tx_aggr_stop(sc, sta, tid);
ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid);
+ ath9k_ps_restore(sc);
break;
case IEEE80211_AMPDU_TX_OPERATIONAL:
+ ath9k_ps_wakeup(sc);
ath_tx_aggr_resume(sc, sta, tid);
+ ath9k_ps_restore(sc);
break;
default:
ath_print(ath9k_hw_common(sc->sc_ah), ATH_DBG_FATAL,
pci_write_config_byte(pdev, ATH_PCIE_CAP_LINK_CTRL, aspm);
}
-const static struct ath_bus_ops ath_pci_bus_ops = {
+static const struct ath_bus_ops ath_pci_bus_ops = {
.read_cachesize = ath_pci_read_cachesize,
.cleanup = ath_pci_cleanup,
.eeprom_read = ath_pci_eeprom_read,
if (npend) {
int r;
- ath_print(common, ATH_DBG_XMIT,
+ ath_print(common, ATH_DBG_FATAL,
"Unable to stop TxDMA. Reset HAL!\n");
spin_lock_bh(&sc->sc_resetlock);
- r = ath9k_hw_reset(ah, sc->sc_ah->curchan, true);
+ r = ath9k_hw_reset(ah, sc->sc_ah->curchan, false);
if (r)
ath_print(common, ATH_DBG_FATAL,
"Unable to reset hardware; reset status %d\n",
* For HT capable stations, we save tidno for later use.
* We also override seqno set by upper layer with the one
* in tx aggregation state.
- *
- * If fragmentation is on, the sequence number is
- * not overridden, since it has been
- * incremented by the fragmentation routine.
- *
- * FIXME: check if the fragmentation threshold exceeds
- * IEEE80211 max.
*/
tid = ATH_AN_2_TID(an, bf->bf_tidno);
- hdr->seq_ctrl = cpu_to_le16(tid->seq_next <<
- IEEE80211_SEQ_SEQ_SHIFT);
+ hdr->seq_ctrl = cpu_to_le16(tid->seq_next << IEEE80211_SEQ_SEQ_SHIFT);
bf->bf_seqno = tid->seq_next;
INCR(tid->seq_next, IEEE80211_SEQ_MAX);
}
bf->bf_keyix = ATH9K_TXKEYIX_INVALID;
}
- if (ieee80211_is_data_qos(fc) && (sc->sc_flags & SC_OP_TXAGGR))
+ if (ieee80211_is_data_qos(fc) && bf_isht(bf) &&
+ (sc->sc_flags & SC_OP_TXAGGR))
assign_aggr_tid_seqno(skb, bf);
bf->bf_mpdu = skb;
struct ath_wiphy *aphy = hw->priv;
struct ath_softc *sc = aphy->sc;
struct ath_common *common = ath9k_hw_common(sc->sc_ah);
- int hdrlen, padsize;
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
+ int padpos, padsize;
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
struct ath_tx_control txctl;
* BSSes.
*/
if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
- struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
sc->tx.seq_no += 0x10;
hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
}
/* Add the padding after the header if this is not already done */
- hdrlen = ieee80211_get_hdrlen_from_skb(skb);
- if (hdrlen & 3) {
- padsize = hdrlen % 4;
+ padpos = ath9k_cmn_padpos(hdr->frame_control);
+ padsize = padpos & 3;
+ if (padsize && skb->len>padpos) {
if (skb_headroom(skb) < padsize) {
ath_print(common, ATH_DBG_XMIT,
"TX CABQ padding failed\n");
return;
}
skb_push(skb, padsize);
- memmove(skb->data, skb->data + padsize, hdrlen);
+ memmove(skb->data, skb->data + padsize, padpos);
}
txctl.txq = sc->beacon.cabq;
struct ieee80211_hw *hw = sc->hw;
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
struct ath_common *common = ath9k_hw_common(sc->sc_ah);
- int hdrlen, padsize;
+ struct ieee80211_hdr * hdr = (struct ieee80211_hdr *)skb->data;
+ int padpos, padsize;
ath_print(common, ATH_DBG_XMIT, "TX complete: skb: %p\n", skb);
tx_info->flags |= IEEE80211_TX_STAT_ACK;
}
- hdrlen = ieee80211_get_hdrlen_from_skb(skb);
- padsize = hdrlen & 3;
- if (padsize && hdrlen >= 24) {
+ padpos = ath9k_cmn_padpos(hdr->frame_control);
+ padsize = padpos & 3;
+ if (padsize && skb->len>padpos+padsize) {
/*
* Remove MAC header padding before giving the frame back to
* mac80211.
*/
- memmove(skb->data + padsize, skb->data, hdrlen);
+ memmove(skb->data + padsize, skb->data, padpos);
skb_pull(skb, padsize);
}
&txq->axq_q, lastbf->list.prev);
txq->axq_depth--;
- txok = !(ds->ds_txstat.ts_status & ATH9K_TXERR_FILT);
+ txok = !(ds->ds_txstat.ts_status & ATH9K_TXERR_MASK);
txq->axq_tx_inprogress = false;
spin_unlock_bh(&txq->axq_lock);
}
}
-/* Check if a DMA region fits the device constraints.
- * Returns true, if the region is OK for usage with this device. */
-static inline bool b43_dma_address_ok(struct b43_dmaring *ring,
- dma_addr_t addr, size_t size)
-{
- switch (ring->type) {
- case B43_DMA_30BIT:
- if ((u64)addr + size > (1ULL << 30))
- return 0;
- break;
- case B43_DMA_32BIT:
- if ((u64)addr + size > (1ULL << 32))
- return 0;
- break;
- case B43_DMA_64BIT:
- /* Currently we can't have addresses beyond
- * 64bit in the kernel. */
- break;
- }
- return 1;
-}
-
-#define is_4k_aligned(addr) (((u64)(addr) & 0x0FFFull) == 0)
-#define is_8k_aligned(addr) (((u64)(addr) & 0x1FFFull) == 0)
-
-static void b43_unmap_and_free_ringmem(struct b43_dmaring *ring, void *base,
- dma_addr_t dmaaddr, size_t size)
-{
- ssb_dma_unmap_single(ring->dev->dev, dmaaddr, size, DMA_TO_DEVICE);
- free_pages((unsigned long)base, get_order(size));
-}
-
-static void * __b43_get_and_map_ringmem(struct b43_dmaring *ring,
- dma_addr_t *dmaaddr, size_t size,
- gfp_t gfp_flags)
-{
- void *base;
-
- base = (void *)__get_free_pages(gfp_flags, get_order(size));
- if (!base)
- return NULL;
- memset(base, 0, size);
- *dmaaddr = ssb_dma_map_single(ring->dev->dev, base, size,
- DMA_TO_DEVICE);
- if (ssb_dma_mapping_error(ring->dev->dev, *dmaaddr)) {
- free_pages((unsigned long)base, get_order(size));
- return NULL;
- }
-
- return base;
-}
-
-static void * b43_get_and_map_ringmem(struct b43_dmaring *ring,
- dma_addr_t *dmaaddr, size_t size)
-{
- void *base;
-
- base = __b43_get_and_map_ringmem(ring, dmaaddr, size,
- GFP_KERNEL);
- if (!base) {
- b43err(ring->dev->wl, "Failed to allocate or map pages "
- "for DMA ringmemory\n");
- return NULL;
- }
- if (!b43_dma_address_ok(ring, *dmaaddr, size)) {
- /* The memory does not fit our device constraints.
- * Retry with GFP_DMA set to get lower memory. */
- b43_unmap_and_free_ringmem(ring, base, *dmaaddr, size);
- base = __b43_get_and_map_ringmem(ring, dmaaddr, size,
- GFP_KERNEL | GFP_DMA);
- if (!base) {
- b43err(ring->dev->wl, "Failed to allocate or map pages "
- "in the GFP_DMA region for DMA ringmemory\n");
- return NULL;
- }
- if (!b43_dma_address_ok(ring, *dmaaddr, size)) {
- b43_unmap_and_free_ringmem(ring, base, *dmaaddr, size);
- b43err(ring->dev->wl, "Failed to allocate DMA "
- "ringmemory that fits device constraints\n");
- return NULL;
- }
- }
- /* We expect the memory to be 4k aligned, at least. */
- if (B43_WARN_ON(!is_4k_aligned(*dmaaddr))) {
- b43_unmap_and_free_ringmem(ring, base, *dmaaddr, size);
- return NULL;
- }
-
- return base;
-}
-
static int alloc_ringmemory(struct b43_dmaring *ring)
{
- unsigned int required;
- void *base;
- dma_addr_t dmaaddr;
-
- /* There are several requirements to the descriptor ring memory:
- * - The memory region needs to fit the address constraints for the
- * device (same as for frame buffers).
- * - For 30/32bit DMA devices, the descriptor ring must be 4k aligned.
- * - For 64bit DMA devices, the descriptor ring must be 8k aligned.
+ gfp_t flags = GFP_KERNEL;
+
+ /* The specs call for 4K buffers for 30- and 32-bit DMA with 4K
+ * alignment and 8K buffers for 64-bit DMA with 8K alignment. Testing
+ * has shown that 4K is sufficient for the latter as long as the buffer
+ * does not cross an 8K boundary.
+ *
+ * For unknown reasons - possibly a hardware error - the BCM4311 rev
+ * 02, which uses 64-bit DMA, needs the ring buffer in very low memory,
+ * which accounts for the GFP_DMA flag below.
+ *
+ * The flags here must match the flags in free_ringmemory below!
*/
-
if (ring->type == B43_DMA_64BIT)
- required = ring->nr_slots * sizeof(struct b43_dmadesc64);
- else
- required = ring->nr_slots * sizeof(struct b43_dmadesc32);
- if (B43_WARN_ON(required > 0x1000))
+ flags |= GFP_DMA;
+ ring->descbase = ssb_dma_alloc_consistent(ring->dev->dev,
+ B43_DMA_RINGMEMSIZE,
+ &(ring->dmabase), flags);
+ if (!ring->descbase) {
+ b43err(ring->dev->wl, "DMA ringmemory allocation failed\n");
return -ENOMEM;
-
- ring->alloc_descsize = 0x1000;
- base = b43_get_and_map_ringmem(ring, &dmaaddr, ring->alloc_descsize);
- if (!base)
- return -ENOMEM;
- ring->alloc_descbase = base;
- ring->alloc_dmabase = dmaaddr;
-
- if ((ring->type != B43_DMA_64BIT) || is_8k_aligned(dmaaddr)) {
- /* We're on <=32bit DMA, or we already got 8k aligned memory.
- * That's all we need, so we're fine. */
- ring->descbase = base;
- ring->dmabase = dmaaddr;
- return 0;
- }
- b43_unmap_and_free_ringmem(ring, base, dmaaddr, ring->alloc_descsize);
-
- /* Ok, we failed at the 8k alignment requirement.
- * Try to force-align the memory region now. */
- ring->alloc_descsize = 0x2000;
- base = b43_get_and_map_ringmem(ring, &dmaaddr, ring->alloc_descsize);
- if (!base)
- return -ENOMEM;
- ring->alloc_descbase = base;
- ring->alloc_dmabase = dmaaddr;
-
- if (is_8k_aligned(dmaaddr)) {
- /* We're already 8k aligned. That Ok, too. */
- ring->descbase = base;
- ring->dmabase = dmaaddr;
- return 0;
}
- /* Force-align it to 8k */
- ring->descbase = (void *)((u8 *)base + 0x1000);
- ring->dmabase = dmaaddr + 0x1000;
- B43_WARN_ON(!is_8k_aligned(ring->dmabase));
+ memset(ring->descbase, 0, B43_DMA_RINGMEMSIZE);
return 0;
}
static void free_ringmemory(struct b43_dmaring *ring)
{
- b43_unmap_and_free_ringmem(ring, ring->alloc_descbase,
- ring->alloc_dmabase, ring->alloc_descsize);
+ gfp_t flags = GFP_KERNEL;
+
+ if (ring->type == B43_DMA_64BIT)
+ flags |= GFP_DMA;
+
+ ssb_dma_free_consistent(ring->dev->dev, B43_DMA_RINGMEMSIZE,
+ ring->descbase, ring->dmabase, flags);
}
/* Reset the RX DMA channel */
if (unlikely(ssb_dma_mapping_error(ring->dev->dev, addr)))
return 1;
- if (!b43_dma_address_ok(ring, addr, buffersize)) {
- /* We can't support this address. Unmap it again. */
- unmap_descbuffer(ring, addr, buffersize, dma_to_device);
- return 1;
+ switch (ring->type) {
+ case B43_DMA_30BIT:
+ if ((u64)addr + buffersize > (1ULL << 30))
+ goto address_error;
+ break;
+ case B43_DMA_32BIT:
+ if ((u64)addr + buffersize > (1ULL << 32))
+ goto address_error;
+ break;
+ case B43_DMA_64BIT:
+ /* Currently we can't have addresses beyond
+ * 64bit in the kernel. */
+ break;
}
/* The address is OK. */
return 0;
+
+address_error:
+ /* We can't support this address. Unmap it again. */
+ unmap_descbuffer(ring, addr, buffersize, dma_to_device);
+
+ return 1;
}
static bool b43_rx_buffer_is_poisoned(struct b43_dmaring *ring, struct sk_buff *skb)
meta->dmaaddr = dmaaddr;
ring->ops->fill_descriptor(ring, desc, dmaaddr,
ring->rx_buffersize, 0, 0, 0);
- ssb_dma_sync_single_for_device(ring->dev->dev,
- ring->alloc_dmabase,
- ring->alloc_descsize, DMA_TO_DEVICE);
return 0;
}
}
/* Now transfer the whole frame. */
wmb();
- ssb_dma_sync_single_for_device(ring->dev->dev,
- ring->alloc_dmabase,
- ring->alloc_descsize, DMA_TO_DEVICE);
ops->poke_tx(ring, next_slot(ring, slot));
return 0;
} __attribute__ ((__packed__));
/* Misc DMA constants */
+#define B43_DMA_RINGMEMSIZE PAGE_SIZE
#define B43_DMA0_RX_FRAMEOFFSET 30
/* DMA engine tuning knobs */
/* The QOS priority assigned to this ring. Only used for TX rings.
* This is the mac80211 "queue" value. */
u8 queue_prio;
- /* Pointers and size of the originally allocated and mapped memory
- * region for the descriptor ring. */
- void *alloc_descbase;
- dma_addr_t alloc_dmabase;
- unsigned int alloc_descsize;
- /* Pointer to our wireless device. */
struct b43_wldev *dev;
#ifdef CONFIG_B43_DEBUG
/* Maximum number of used slots. */
snr = rx_stats_sig_avg / rx_stats_noise_diff;
rx_status.noise = rx_status.signal -
iwl3945_calc_db_from_ratio(snr);
- rx_status.qual = iwl3945_calc_sig_qual(rx_status.signal,
- rx_status.noise);
-
- /* If noise info not available, calculate signal quality indicator (%)
- * using just the dBm signal level. */
} else {
rx_status.noise = priv->last_rx_noise;
- rx_status.qual = iwl3945_calc_sig_qual(rx_status.signal, 0);
}
- IWL_DEBUG_STATS(priv, "Rssi %d noise %d qual %d sig_avg %d noise_diff %d\n",
- rx_status.signal, rx_status.noise, rx_status.qual,
+ IWL_DEBUG_STATS(priv, "Rssi %d noise %d sig_avg %d noise_diff %d\n",
+ rx_status.signal, rx_status.noise,
rx_stats_sig_avg, rx_stats_noise_diff);
header = (struct ieee80211_hdr *)IWL_RX_DATA(pkt);
rc = -EIO;
}
- priv->alloc_rxb_page--;
- free_pages(cmd.reply_page, priv->hw_params.rx_page_order);
+ iwl_free_pages(priv, cmd.reply_page);
return rc;
}
.use_isr_legacy = true,
.ht_greenfield_support = false,
.led_compensation = 64,
+ .broken_powersave = true,
};
static struct iwl_cfg iwl3945_abg_cfg = {
.use_isr_legacy = true,
.ht_greenfield_support = false,
.led_compensation = 64,
+ .broken_powersave = true,
};
struct pci_device_id iwl3945_hw_card_ids[] = {
*
*****************************************************************************/
extern int iwl3945_calc_db_from_ratio(int sig_ratio);
-extern int iwl3945_calc_sig_qual(int rssi_dbm, int noise_dbm);
extern void iwl3945_rx_replenish(void *data);
extern void iwl3945_rx_queue_reset(struct iwl_priv *priv, struct iwl_rx_queue *rxq);
extern unsigned int iwl3945_fill_beacon_frame(struct iwl_priv *priv,
iwl4965_interpolate_chan(priv, channel, &ch_eeprom_info);
/* calculate tx gain adjustment based on power supply voltage */
- voltage = priv->calib_info->voltage;
+ voltage = le16_to_cpu(priv->calib_info->voltage);
init_voltage = (s32)le32_to_cpu(priv->card_alive_init.voltage);
voltage_compensation =
iwl4965_get_voltage_compensation(voltage, init_voltage);
static inline s32 iwl_temp_calib_to_offset(struct iwl_priv *priv)
{
- u16 *temp_calib = (u16 *)iwl_eeprom_query_addr(priv,
- EEPROM_5000_TEMPERATURE);
- /* offset = temperature - voltage / coef */
- s32 offset = (s32)(temp_calib[0] - temp_calib[1] / IWL_5150_VOLTAGE_TO_TEMPERATURE_COEFF);
- return offset;
+ u16 temperature, voltage;
+ __le16 *temp_calib =
+ (__le16 *)iwl_eeprom_query_addr(priv, EEPROM_5000_TEMPERATURE);
+
+ temperature = le16_to_cpu(temp_calib[0]);
+ voltage = le16_to_cpu(temp_calib[1]);
+
+ /* offset = temp - volt / coeff */
+ return (s32)(temperature - voltage / IWL_5150_VOLTAGE_TO_TEMPERATURE_COEFF);
}
/* Fixed (non-configurable) rx data from phy */
static int iwl5000_set_Xtal_calib(struct iwl_priv *priv)
{
struct iwl_calib_xtal_freq_cmd cmd;
- u16 *xtal_calib = (u16 *)iwl_eeprom_query_addr(priv, EEPROM_5000_XTAL);
+ __le16 *xtal_calib =
+ (__le16 *)iwl_eeprom_query_addr(priv, EEPROM_5000_XTAL);
cmd.hdr.op_code = IWL_PHY_CALIBRATE_CRYSTAL_FRQ_CMD;
cmd.hdr.first_group = 0;
cmd.hdr.groups_num = 1;
cmd.hdr.data_valid = 1;
- cmd.cap_pin1 = (u8)xtal_calib[0];
- cmd.cap_pin2 = (u8)xtal_calib[1];
+ cmd.cap_pin1 = le16_to_cpu(xtal_calib[0]);
+ cmd.cap_pin2 = le16_to_cpu(xtal_calib[1]);
return iwl_calib_set(&priv->calib_results[IWL_CALIB_XTAL],
(u8 *)&cmd, sizeof(cmd));
}
};
/* mbps, mcs */
-const static struct iwl_rate_mcs_info iwl_rate_mcs[IWL_RATE_COUNT] = {
+static const struct iwl_rate_mcs_info iwl_rate_mcs[IWL_RATE_COUNT] = {
{ "1", "BPSK DSSS"},
{ "2", "QPSK DSSS"},
{"5.5", "BPSK CCK"},
}
#ifdef CONFIG_IWLWIFI_DEBUG
- if (!(iwl_get_debug_level(priv) & IWL_DL_FW_ERRORS))
+ if (!(iwl_get_debug_level(priv) & IWL_DL_FW_ERRORS) && !full_log)
size = (size > DEFAULT_DUMP_EVENT_LOG_ENTRIES)
? DEFAULT_DUMP_EVENT_LOG_ENTRIES : size;
#else
priv->ibss_beacon = NULL;
- spin_lock_init(&priv->lock);
spin_lock_init(&priv->sta_lock);
spin_lock_init(&priv->hcmd_lock);
(unsigned long long) pci_resource_len(pdev, 0));
IWL_DEBUG_INFO(priv, "pci_resource_base = %p\n", priv->hw_base);
- /* this spin lock will be used in apm_ops.init and EEPROM access
+ /* these spin locks will be used in apm_ops.init and EEPROM access
* we should init now
*/
spin_lock_init(&priv->reg_lock);
+ spin_lock_init(&priv->lock);
iwl_hw_detect(priv);
IWL_INFO(priv, "Detected Intel Wireless WiFi Link %s REV=0x%X\n",
priv->cfg->name, priv->hw_rev);
* The MAC (uCode processor, etc.) does not need to be powered up for accessing
* the CSR registers.
*
- * NOTE: Newer devices using one-time-programmable (OTP) memory
- * require device to be awake in order to read this memory
+ * NOTE: Device does need to be awake in order to read this memory
* via CSR_EEPROM and CSR_OTP registers
*/
#define CSR_BASE (0x000)
/*
* EEPROM and OTP (one-time-programmable) memory reads
*
- * NOTE: For (newer) devices using OTP, device must be awake, initialized via
- * apm_ops.init() in order to read. Older devices (3945/4965/5000)
- * use EEPROM and do not require this.
+ * NOTE: Device must be awake, initialized via apm_ops.init(),
+ * in order to read.
*/
#define CSR_EEPROM_REG (CSR_BASE+0x02c)
#define CSR_EEPROM_GP (CSR_BASE+0x030)
u32 last_beacon_time;
u64 last_tsf;
- /* eeprom */
+ /* eeprom -- this is in the card's little endian byte order */
u8 *eeprom;
int nvm_device_type;
struct iwl_eeprom_calib_info *calib_info;
return ((ch->flags & EEPROM_CHANNEL_IBSS)) ? 1 : 0;
}
+static inline void __iwl_free_pages(struct iwl_priv *priv, struct page *page)
+{
+ __free_pages(page, priv->hw_params.rx_page_order);
+ priv->alloc_rxb_page--;
+}
+
+static inline void iwl_free_pages(struct iwl_priv *priv, unsigned long page)
+{
+ free_pages(page, priv->hw_params.rx_page_order);
+ priv->alloc_rxb_page--;
+}
#endif /* __iwl_dev_h__ */
return ret;
}
-static int iwl_read_otp_word(struct iwl_priv *priv, u16 addr, u16 *eeprom_data)
+static int iwl_read_otp_word(struct iwl_priv *priv, u16 addr, __le16 *eeprom_data)
{
int ret = 0;
u32 r;
CSR_OTP_GP_REG_ECC_CORR_STATUS_MSK);
IWL_ERR(priv, "Correctable OTP ECC error, continue read\n");
}
- *eeprom_data = le16_to_cpu((__force __le16)(r >> 16));
+ *eeprom_data = cpu_to_le16(r >> 16);
return 0;
}
*/
static bool iwl_is_otp_empty(struct iwl_priv *priv)
{
- u16 next_link_addr = 0, link_value;
+ u16 next_link_addr = 0;
+ __le16 link_value;
bool is_empty = false;
/* locate the beginning of OTP link list */
static int iwl_find_otp_image(struct iwl_priv *priv,
u16 *validblockaddr)
{
- u16 next_link_addr = 0, link_value = 0, valid_addr;
+ u16 next_link_addr = 0, valid_addr;
+ __le16 link_value = 0;
int usedblocks = 0;
/* set addressing mode to absolute to traverse the link list */
* check for more block on the link list
*/
valid_addr = next_link_addr;
- next_link_addr = link_value * sizeof(u16);
+ next_link_addr = le16_to_cpu(link_value) * sizeof(u16);
IWL_DEBUG_INFO(priv, "OTP blocks %d addr 0x%x\n",
usedblocks, next_link_addr);
if (iwl_read_otp_word(priv, next_link_addr, &link_value))
*/
int iwl_eeprom_init(struct iwl_priv *priv)
{
- u16 *e;
+ __le16 *e;
u32 gp = iwl_read32(priv, CSR_EEPROM_GP);
int sz;
int ret;
ret = -ENOMEM;
goto alloc_err;
}
- e = (u16 *)priv->eeprom;
+ e = (__le16 *)priv->eeprom;
- if (priv->nvm_device_type == NVM_DEVICE_TYPE_OTP) {
- /* OTP reads require powered-up chip */
- priv->cfg->ops->lib->apm_ops.init(priv);
- }
+ priv->cfg->ops->lib->apm_ops.init(priv);
ret = priv->cfg->ops->lib->eeprom_ops.verify_signature(priv);
if (ret < 0) {
}
for (addr = validblockaddr; addr < validblockaddr + sz;
addr += sizeof(u16)) {
- u16 eeprom_data;
+ __le16 eeprom_data;
ret = iwl_read_otp_word(priv, addr, &eeprom_data);
if (ret)
e[cache_addr / 2] = eeprom_data;
cache_addr += sizeof(u16);
}
-
- /*
- * Now that OTP reads are complete, reset chip to save
- * power until we load uCode during "up".
- */
- priv->cfg->ops->lib->apm_ops.stop(priv);
-
} else {
/* eeprom is an array of 16bit values */
for (addr = 0; addr < sz; addr += sizeof(u16)) {
goto done;
}
r = _iwl_read_direct32(priv, CSR_EEPROM_REG);
- e[addr / 2] = le16_to_cpu((__force __le16)(r >> 16));
+ e[addr / 2] = cpu_to_le16(r >> 16);
}
}
ret = 0;
err:
if (ret)
iwl_eeprom_free(priv);
+ /* Reset chip to save power until we load uCode during "up". */
+ priv->cfg->ops->lib->apm_ops.stop(priv);
alloc_err:
return ret;
}
ch_info->ht40_eeprom = *eeprom_ch;
ch_info->ht40_max_power_avg = eeprom_ch->max_power_avg;
ch_info->ht40_flags = eeprom_ch->flags;
- ch_info->ht40_extension_channel &= ~clear_ht40_extension_channel;
+ if (eeprom_ch->flags & EEPROM_CHANNEL_VALID)
+ ch_info->ht40_extension_channel &= ~clear_ht40_extension_channel;
return 0;
}
*
*/
struct iwl_eeprom_enhanced_txpwr {
- u16 common;
+ __le16 common;
s8 chain_a_max;
s8 chain_b_max;
s8 chain_c_max;
struct iwl_eeprom_calib_info {
u8 saturation_power24; /* half-dBm (e.g. "34" = 17 dBm) */
u8 saturation_power52; /* half-dBm */
- s16 voltage; /* signed */
+ __le16 voltage; /* signed */
struct iwl_eeprom_calib_subband_info
band_info[EEPROM_TX_POWER_BANDS];
} __attribute__ ((packed));
}
fail:
if (cmd->reply_page) {
- free_pages(cmd->reply_page, priv->hw_params.rx_page_order);
+ iwl_free_pages(priv, cmd->reply_page);
cmd->reply_page = 0;
}
out:
pci_unmap_page(priv->pci_dev, rxq->pool[i].page_dma,
PAGE_SIZE << priv->hw_params.rx_page_order,
PCI_DMA_FROMDEVICE);
- __free_pages(rxq->pool[i].page,
- priv->hw_params.rx_page_order);
+ __iwl_free_pages(priv, rxq->pool[i].page);
rxq->pool[i].page = NULL;
- priv->alloc_rxb_page--;
}
}
pci_unmap_page(priv->pci_dev, rxq->pool[i].page_dma,
PAGE_SIZE << priv->hw_params.rx_page_order,
PCI_DMA_FROMDEVICE);
- priv->alloc_rxb_page--;
- __free_pages(rxq->pool[i].page,
- priv->hw_params.rx_page_order);
+ __iwl_free_pages(priv, rxq->pool[i].page);
rxq->pool[i].page = NULL;
}
list_add_tail(&rxq->pool[i].list, &rxq->rx_used);
}
EXPORT_SYMBOL(iwl_reply_statistics);
-#define PERFECT_RSSI (-20) /* dBm */
-#define WORST_RSSI (-95) /* dBm */
-#define RSSI_RANGE (PERFECT_RSSI - WORST_RSSI)
-
-/* Calculate an indication of rx signal quality (a percentage, not dBm!).
- * See http://www.ces.clemson.edu/linux/signal_quality.shtml for info
- * about formulas used below. */
-static int iwl_calc_sig_qual(int rssi_dbm, int noise_dbm)
-{
- int sig_qual;
- int degradation = PERFECT_RSSI - rssi_dbm;
-
- /* If we get a noise measurement, use signal-to-noise ratio (SNR)
- * as indicator; formula is (signal dbm - noise dbm).
- * SNR at or above 40 is a great signal (100%).
- * Below that, scale to fit SNR of 0 - 40 dB within 0 - 100% indicator.
- * Weakest usable signal is usually 10 - 15 dB SNR. */
- if (noise_dbm) {
- if (rssi_dbm - noise_dbm >= 40)
- return 100;
- else if (rssi_dbm < noise_dbm)
- return 0;
- sig_qual = ((rssi_dbm - noise_dbm) * 5) / 2;
-
- /* Else use just the signal level.
- * This formula is a least squares fit of data points collected and
- * compared with a reference system that had a percentage (%) display
- * for signal quality. */
- } else
- sig_qual = (100 * (RSSI_RANGE * RSSI_RANGE) - degradation *
- (15 * RSSI_RANGE + 62 * degradation)) /
- (RSSI_RANGE * RSSI_RANGE);
-
- if (sig_qual > 100)
- sig_qual = 100;
- else if (sig_qual < 1)
- sig_qual = 0;
-
- return sig_qual;
-}
-
/* Calc max signal level (dBm) among 3 possible receivers */
static inline int iwl_calc_rssi(struct iwl_priv *priv,
struct iwl_rx_phy_res *rx_resp)
if (iwl_is_associated(priv) &&
!test_bit(STATUS_SCANNING, &priv->status)) {
rx_status.noise = priv->last_rx_noise;
- rx_status.qual = iwl_calc_sig_qual(rx_status.signal,
- rx_status.noise);
} else {
rx_status.noise = IWL_NOISE_MEAS_NOT_AVAILABLE;
- rx_status.qual = iwl_calc_sig_qual(rx_status.signal, 0);
}
/* Reset beacon noise level if not associated. */
iwl_dbg_report_frame(priv, phy_res, len, header, 1);
#endif
iwl_dbg_log_rx_data_frame(priv, len, header);
- IWL_DEBUG_STATS_LIMIT(priv, "Rssi %d, noise %d, qual %d, TSF %llu\n",
- rx_status.signal, rx_status.noise, rx_status.qual,
+ IWL_DEBUG_STATS_LIMIT(priv, "Rssi %d, noise %d, TSF %llu\n",
+ rx_status.signal, rx_status.noise,
(unsigned long long)rx_status.mactime);
/*
clear_bit(STATUS_SCAN_HW, &priv->status);
}
- priv->alloc_rxb_page--;
- free_pages(cmd.reply_page, priv->hw_params.rx_page_order);
+ iwl_free_pages(priv, cmd.reply_page);
return ret;
}
break;
}
}
-
- priv->alloc_rxb_page--;
- free_pages(cmd.reply_page, priv->hw_params.rx_page_order);
+ iwl_free_pages(priv, cmd.reply_page);
return ret;
}
break;
}
}
-
- priv->alloc_rxb_page--;
- free_pages(cmd.reply_page, priv->hw_params.rx_page_order);
+ iwl_free_pages(priv, cmd.reply_page);
return ret;
}
int txq_id;
/* Tx queues */
- if (priv->txq)
+ if (priv->txq) {
for (txq_id = 0; txq_id < priv->hw_params.max_txq_num;
txq_id++)
if (txq_id == IWL_CMD_QUEUE_NUM)
iwl_cmd_queue_free(priv);
else
iwl_tx_queue_free(priv, txq_id);
+ }
iwl_free_dma_ptr(priv, &priv->kw);
iwl_free_dma_ptr(priv, &priv->scd_bc_tbls);
txq = &priv->txq[txq_id];
q = &txq->q;
+ if ((iwl_queue_space(q) < q->high_mark))
+ goto drop;
+
spin_lock_irqsave(&priv->lock, flags);
idx = get_cmd_index(q, q->write_ptr, 0);
break;
}
- free_pages(cmd.reply_page, priv->hw_params.rx_page_order);
+ iwl_free_pages(priv, cmd.reply_page);
return rc;
}
pci_unmap_page(priv->pci_dev, rxq->pool[i].page_dma,
PAGE_SIZE << priv->hw_params.rx_page_order,
PCI_DMA_FROMDEVICE);
- priv->alloc_rxb_page--;
- __free_pages(rxq->pool[i].page,
- priv->hw_params.rx_page_order);
+ __iwl_free_pages(priv, rxq->pool[i].page);
rxq->pool[i].page = NULL;
}
list_add_tail(&rxq->pool[i].list, &rxq->rx_used);
pci_unmap_page(priv->pci_dev, rxq->pool[i].page_dma,
PAGE_SIZE << priv->hw_params.rx_page_order,
PCI_DMA_FROMDEVICE);
- __free_pages(rxq->pool[i].page,
- priv->hw_params.rx_page_order);
+ __iwl_free_pages(priv, rxq->pool[i].page);
rxq->pool[i].page = NULL;
- priv->alloc_rxb_page--;
}
}
return (int)ratio2dB[sig_ratio];
}
-#define PERFECT_RSSI (-20) /* dBm */
-#define WORST_RSSI (-95) /* dBm */
-#define RSSI_RANGE (PERFECT_RSSI - WORST_RSSI)
-
-/* Calculate an indication of rx signal quality (a percentage, not dBm!).
- * See http://www.ces.clemson.edu/linux/signal_quality.shtml for info
- * about formulas used below. */
-int iwl3945_calc_sig_qual(int rssi_dbm, int noise_dbm)
-{
- int sig_qual;
- int degradation = PERFECT_RSSI - rssi_dbm;
-
- /* If we get a noise measurement, use signal-to-noise ratio (SNR)
- * as indicator; formula is (signal dbm - noise dbm).
- * SNR at or above 40 is a great signal (100%).
- * Below that, scale to fit SNR of 0 - 40 dB within 0 - 100% indicator.
- * Weakest usable signal is usually 10 - 15 dB SNR. */
- if (noise_dbm) {
- if (rssi_dbm - noise_dbm >= 40)
- return 100;
- else if (rssi_dbm < noise_dbm)
- return 0;
- sig_qual = ((rssi_dbm - noise_dbm) * 5) / 2;
-
- /* Else use just the signal level.
- * This formula is a least squares fit of data points collected and
- * compared with a reference system that had a percentage (%) display
- * for signal quality. */
- } else
- sig_qual = (100 * (RSSI_RANGE * RSSI_RANGE) - degradation *
- (15 * RSSI_RANGE + 62 * degradation)) /
- (RSSI_RANGE * RSSI_RANGE);
-
- if (sig_qual > 100)
- sig_qual = 100;
- else if (sig_qual < 1)
- sig_qual = 0;
-
- return sig_qual;
-}
-
/**
* iwl3945_rx_handle - Main entry function for receiving responses from uCode
*
}
#ifdef CONFIG_IWLWIFI_DEBUG
- if (!(iwl_get_debug_level(priv) & IWL_DL_FW_ERRORS))
+ if (!(iwl_get_debug_level(priv) & IWL_DL_FW_ERRORS) && !full_log)
size = (size > DEFAULT_IWL3945_DUMP_EVENT_LOG_ENTRIES)
? DEFAULT_IWL3945_DUMP_EVENT_LOG_ENTRIES : size;
#else
priv->retry_rate = 1;
priv->ibss_beacon = NULL;
- spin_lock_init(&priv->lock);
spin_lock_init(&priv->sta_lock);
spin_lock_init(&priv->hcmd_lock);
/* Tell mac80211 our characteristics */
hw->flags = IEEE80211_HW_SIGNAL_DBM |
IEEE80211_HW_NOISE_DBM |
- IEEE80211_HW_SPECTRUM_MGMT |
- IEEE80211_HW_SUPPORTS_PS |
- IEEE80211_HW_SUPPORTS_DYNAMIC_PS;
+ IEEE80211_HW_SPECTRUM_MGMT;
+
+ if (!priv->cfg->broken_powersave)
+ hw->flags |= IEEE80211_HW_SUPPORTS_PS |
+ IEEE80211_HW_SUPPORTS_DYNAMIC_PS;
hw->wiphy->interface_modes =
BIT(NL80211_IFTYPE_STATION) |
* PCI Tx retries from interfering with C3 CPU state */
pci_write_config_byte(pdev, 0x41, 0x00);
- /* this spin lock will be used in apm_ops.init and EEPROM access
+ /* these spin locks will be used in apm_ops.init and EEPROM access
* we should init now
*/
spin_lock_init(&priv->reg_lock);
+ spin_lock_init(&priv->lock);
/***********************
* 4. Read EEPROM
struct sk_buff_head rx_list;
struct list_head rx_tickets;
- struct list_head rx_packets[IWM_RX_ID_HASH];
+ struct list_head rx_packets[IWM_RX_ID_HASH + 1];
struct workqueue_struct *rx_wq;
struct work_struct rx_worker;
int iwm_down(struct iwm_priv *iwm);
/* TX API */
-u16 iwm_tid_to_queue(u16 tid);
+int iwm_tid_to_queue(u16 tid);
void iwm_tx_credit_inc(struct iwm_priv *iwm, int id, int total_freed_pages);
void iwm_tx_worker(struct work_struct *work);
int iwm_xmit_frame(struct sk_buff *skb, struct net_device *netdev);
*/
static const u16 iwm_1d_to_queue[8] = { 1, 0, 0, 1, 2, 2, 3, 3 };
-u16 iwm_tid_to_queue(u16 tid)
+int iwm_tid_to_queue(u16 tid)
{
if (tid > IWM_UMAC_TID_NR - 2)
return -EINVAL;
if (!stop) {
struct iwm_tx_queue *txq;
- u16 queue = iwm_tid_to_queue(bit);
+ int queue = iwm_tid_to_queue(bit);
if (queue < 0)
continue;
#include <linux/delay.h>
#include <linux/etherdevice.h>
#include <linux/netdevice.h>
+#include <linux/if_ether.h>
#include <linux/if_arp.h>
#include <linux/kthread.h>
#include <linux/kfifo.h>
mesh_dev->netdev_ops = &mesh_netdev_ops;
mesh_dev->ethtool_ops = &lbs_ethtool_ops;
- memcpy(mesh_dev->dev_addr, priv->dev->dev_addr,
- sizeof(priv->dev->dev_addr));
+ memcpy(mesh_dev->dev_addr, priv->dev->dev_addr, ETH_ALEN);
SET_NETDEV_DEV(priv->mesh_dev, priv->dev->dev.parent);
chan_count = lbs_scan_create_channel_list(priv, chan_list);
netif_stop_queue(priv->dev);
- netif_carrier_off(priv->dev);
- if (priv->mesh_dev) {
+ if (priv->mesh_dev)
netif_stop_queue(priv->mesh_dev);
- netif_carrier_off(priv->mesh_dev);
- }
/* Prepare to continue an interrupted scan */
lbs_deb_scan("chan_count %d, scan_channel %d\n",
priv->scan_channel = 0;
out:
- if (priv->connect_status == LBS_CONNECTED) {
- netif_carrier_on(priv->dev);
- if (!priv->tx_pending_len)
- netif_wake_queue(priv->dev);
- }
- if (priv->mesh_dev && (priv->mesh_connect_status == LBS_CONNECTED)) {
- netif_carrier_on(priv->mesh_dev);
- if (!priv->tx_pending_len)
- netif_wake_queue(priv->mesh_dev);
- }
+ if (priv->connect_status == LBS_CONNECTED && !priv->tx_pending_len)
+ netif_wake_queue(priv->dev);
+
+ if (priv->mesh_dev && (priv->mesh_connect_status == LBS_CONNECTED) &&
+ !priv->tx_pending_len)
+ netif_wake_queue(priv->mesh_dev);
+
kfree(chan_list);
lbs_deb_leave_args(LBS_DEB_SCAN, "ret %d", ret);
if (priv->connect_status == LBS_CONNECTED) {
memcpy(extra, priv->curbssparams.ssid,
priv->curbssparams.ssid_len);
- extra[priv->curbssparams.ssid_len] = '\0';
} else {
memset(extra, 0, 32);
- extra[priv->curbssparams.ssid_len] = '\0';
}
/*
* If none, we may want to get the one that was set
stats.band = IEEE80211_BAND_2GHZ;
stats.signal = prxpd->snr;
stats.noise = prxpd->nf;
- stats.qual = prxpd->snr - prxpd->nf;
/* Marvell rate index has a hole at value 4 */
if (prxpd->rx_rate > 4)
--prxpd->rx_rate;
#define MAX_RID_LEN 1024
/* Helper routine to record keys
- * Do not call from interrupt context */
+ * It is called under orinoco_lock so it may not sleep */
static int orinoco_set_key(struct orinoco_private *priv, int index,
enum orinoco_alg alg, const u8 *key, int key_len,
const u8 *seq, int seq_len)
kzfree(priv->keys[index].seq);
if (key_len) {
- priv->keys[index].key = kzalloc(key_len, GFP_KERNEL);
+ priv->keys[index].key = kzalloc(key_len, GFP_ATOMIC);
if (!priv->keys[index].key)
goto nomem;
} else
priv->keys[index].key = NULL;
if (seq_len) {
- priv->keys[index].seq = kzalloc(seq_len, GFP_KERNEL);
+ priv->keys[index].seq = kzalloc(seq_len, GFP_ATOMIC);
if (!priv->keys[index].seq)
goto free_key;
} else
#define PAIRWISE_KEY_ENTRY(__idx) \
( PAIRWISE_KEY_TABLE_BASE + ((__idx) * sizeof(struct hw_key_entry)) )
#define MAC_IVEIV_ENTRY(__idx) \
- ( MAC_IVEIV_TABLE_BASE + ((__idx) & sizeof(struct mac_iveiv_entry)) )
+ ( MAC_IVEIV_TABLE_BASE + ((__idx) * sizeof(struct mac_iveiv_entry)) )
#define MAC_WCID_ATTR_ENTRY(__idx) \
( MAC_WCID_ATTRIBUTE_BASE + ((__idx) * sizeof(u32)) )
#define SHARED_KEY_ENTRY(__idx) \
#include <linux/module.h>
#include "rt2x00.h"
-#ifdef CONFIG_RT2800USB
+#if defined(CONFIG_RT2800USB) || defined(CONFIG_RT2800USB_MODULE)
#include "rt2x00usb.h"
#endif
#include "rt2800lib.h"
if (rt2x00_intf_is_usb(rt2x00dev)) {
rt2800_register_write(rt2x00dev, USB_DMA_CFG, 0x00000000);
-#ifdef CONFIG_RT2800USB
+#if defined(CONFIG_RT2800USB) || defined(CONFIG_RT2800USB_MODULE)
rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0,
USB_MODE_RESET, REGISTER_TIMEOUT);
#endif
unsigned int i;
u16 eeprom;
+ /*
+ * Disable powersaving as default on PCI devices.
+ */
+ if (rt2x00_intf_is_pci(rt2x00dev))
+ rt2x00dev->hw->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT;
+
/*
* Initialize all hw fields.
*/
IEEE80211_HT_CAP_SGI_20 |
IEEE80211_HT_CAP_SGI_40 |
IEEE80211_HT_CAP_TX_STBC |
- IEEE80211_HT_CAP_RX_STBC |
- IEEE80211_HT_CAP_PSMP_SUPPORT;
+ IEEE80211_HT_CAP_RX_STBC;
spec->ht.ampdu_factor = 3;
spec->ht.ampdu_density = 4;
spec->ht.mcs.tx_params =
rt2800_register_multiread(rt2x00dev, offset,
&iveiv_entry, sizeof(iveiv_entry));
- memcpy(&iveiv_entry.iv[0], iv16, sizeof(iv16));
- memcpy(&iveiv_entry.iv[4], iv32, sizeof(iv32));
+ memcpy(iv16, &iveiv_entry.iv[0], sizeof(*iv16));
+ memcpy(iv32, &iveiv_entry.iv[4], sizeof(*iv32));
}
static int rt2800_set_rts_threshold(struct ieee80211_hw *hw, u32 value)
{ USB_DEVICE(0x1737, 0x0070), USB_DEVICE_DATA(&rt2800usb_ops) },
{ USB_DEVICE(0x1737, 0x0071), USB_DEVICE_DATA(&rt2800usb_ops) },
{ USB_DEVICE(0x1737, 0x0077), USB_DEVICE_DATA(&rt2800usb_ops) },
+ { USB_DEVICE(0x1737, 0x0079), USB_DEVICE_DATA(&rt2800usb_ops) },
/* Logitec */
{ USB_DEVICE(0x0789, 0x0162), USB_DEVICE_DATA(&rt2800usb_ops) },
{ USB_DEVICE(0x0789, 0x0163), USB_DEVICE_DATA(&rt2800usb_ops) },
char *tx_power;
unsigned int i;
+ /*
+ * Disable powersaving as default.
+ */
+ rt2x00dev->hw->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT;
+
/*
* Initialize all hw fields.
*/
rx_status.antenna = (flags2 >> 15) & 1;
/* TODO: improve signal/rssi reporting */
- rx_status.qual = flags2 & 0xFF;
rx_status.signal = (flags2 >> 8) & 0x7F;
/* XXX: is this correct? */
rx_status.rate_idx = (flags >> 20) & 0xF;
}
}
- if (loop >= INIT_LOOP) {
+ if (loop > INIT_LOOP) {
wl1251_error("timeout waiting for the hardware to "
"complete initialization");
return -EIO;
return ret;
}
-static int wl1271_build_basic_rates(char *rates, u8 band)
+static int wl1271_build_basic_rates(u8 *rates, u8 band)
{
u8 index = 0;
return index;
}
-static int wl1271_build_extended_rates(char *rates, u8 band)
+static int wl1271_build_extended_rates(u8 *rates, u8 band)
{
u8 index = 0;
return r;
}
-static int ofdm_qual_db(u8 status_quality, u8 zd_rate, unsigned int size)
-{
- static const u16 constants[] = {
- 715, 655, 585, 540, 470, 410, 360, 315,
- 270, 235, 205, 175, 150, 125, 105, 85,
- 65, 50, 40, 25, 15
- };
-
- int i;
- u32 x;
-
- /* It seems that their quality parameter is somehow per signal
- * and is now transferred per bit.
- */
- switch (zd_rate) {
- case ZD_OFDM_RATE_6M:
- case ZD_OFDM_RATE_12M:
- case ZD_OFDM_RATE_24M:
- size *= 2;
- break;
- case ZD_OFDM_RATE_9M:
- case ZD_OFDM_RATE_18M:
- case ZD_OFDM_RATE_36M:
- case ZD_OFDM_RATE_54M:
- size *= 4;
- size /= 3;
- break;
- case ZD_OFDM_RATE_48M:
- size *= 3;
- size /= 2;
- break;
- default:
- return -EINVAL;
- }
-
- x = (10000 * status_quality)/size;
- for (i = 0; i < ARRAY_SIZE(constants); i++) {
- if (x > constants[i])
- break;
- }
-
- switch (zd_rate) {
- case ZD_OFDM_RATE_6M:
- case ZD_OFDM_RATE_9M:
- i += 3;
- break;
- case ZD_OFDM_RATE_12M:
- case ZD_OFDM_RATE_18M:
- i += 5;
- break;
- case ZD_OFDM_RATE_24M:
- case ZD_OFDM_RATE_36M:
- i += 9;
- break;
- case ZD_OFDM_RATE_48M:
- case ZD_OFDM_RATE_54M:
- i += 15;
- break;
- default:
- return -EINVAL;
- }
-
- return i;
-}
-
-static int ofdm_qual_percent(u8 status_quality, u8 zd_rate, unsigned int size)
-{
- int r;
-
- r = ofdm_qual_db(status_quality, zd_rate, size);
- ZD_ASSERT(r >= 0);
- if (r < 0)
- r = 0;
-
- r = (r * 100)/29;
- return r <= 100 ? r : 100;
-}
-
-static unsigned int log10times100(unsigned int x)
-{
- static const u8 log10[] = {
- 0,
- 0, 30, 47, 60, 69, 77, 84, 90, 95, 100,
- 104, 107, 111, 114, 117, 120, 123, 125, 127, 130,
- 132, 134, 136, 138, 139, 141, 143, 144, 146, 147,
- 149, 150, 151, 153, 154, 155, 156, 157, 159, 160,
- 161, 162, 163, 164, 165, 166, 167, 168, 169, 169,
- 170, 171, 172, 173, 174, 174, 175, 176, 177, 177,
- 178, 179, 179, 180, 181, 181, 182, 183, 183, 184,
- 185, 185, 186, 186, 187, 188, 188, 189, 189, 190,
- 190, 191, 191, 192, 192, 193, 193, 194, 194, 195,
- 195, 196, 196, 197, 197, 198, 198, 199, 199, 200,
- 200, 200, 201, 201, 202, 202, 202, 203, 203, 204,
- 204, 204, 205, 205, 206, 206, 206, 207, 207, 207,
- 208, 208, 208, 209, 209, 210, 210, 210, 211, 211,
- 211, 212, 212, 212, 213, 213, 213, 213, 214, 214,
- 214, 215, 215, 215, 216, 216, 216, 217, 217, 217,
- 217, 218, 218, 218, 219, 219, 219, 219, 220, 220,
- 220, 220, 221, 221, 221, 222, 222, 222, 222, 223,
- 223, 223, 223, 224, 224, 224, 224,
- };
-
- return x < ARRAY_SIZE(log10) ? log10[x] : 225;
-}
-
-enum {
- MAX_CCK_EVM_DB = 45,
-};
-
-static int cck_evm_db(u8 status_quality)
-{
- return (20 * log10times100(status_quality)) / 100;
-}
-
-static int cck_snr_db(u8 status_quality)
-{
- int r = MAX_CCK_EVM_DB - cck_evm_db(status_quality);
- ZD_ASSERT(r >= 0);
- return r;
-}
-
-static int cck_qual_percent(u8 status_quality)
-{
- int r;
-
- r = cck_snr_db(status_quality);
- r = (100*r)/17;
- return r <= 100 ? r : 100;
-}
-
static inline u8 zd_rate_from_ofdm_plcp_header(const void *rx_frame)
{
return ZD_OFDM | zd_ofdm_plcp_header_rate(rx_frame);
}
-u8 zd_rx_qual_percent(const void *rx_frame, unsigned int size,
- const struct rx_status *status)
-{
- return (status->frame_status&ZD_RX_OFDM) ?
- ofdm_qual_percent(status->signal_quality_ofdm,
- zd_rate_from_ofdm_plcp_header(rx_frame),
- size) :
- cck_qual_percent(status->signal_quality_cck);
-}
-
/**
* zd_rx_rate - report zd-rate
* @rx_frame - received frame
struct rx_status;
-u8 zd_rx_qual_percent(const void *rx_frame, unsigned int size,
- const struct rx_status *status);
-
u8 zd_rx_rate(const void *rx_frame, const struct rx_status *status);
struct zd_mc_hash {
stats.freq = zd_channels[_zd_chip_get_channel(&mac->chip) - 1].center_freq;
stats.band = IEEE80211_BAND_2GHZ;
stats.signal = status->signal_strength;
- stats.qual = zd_rx_qual_percent(buffer,
- length - sizeof(struct rx_status),
- status);
rate = zd_rx_rate(buffer, status);
#define PCI_DEVICE_ID_AMD_GOLAM_7450 0x7450
#define PCI_DEVICE_ID_AMD_POGO_7458 0x7458
-/* AMD PCIX bridge registers */
+/* AMD PCI-X bridge registers */
#define PCIX_MEM_BASE_LIMIT_OFFSET 0x1C
#define PCIX_MISCII_OFFSET 0x48
#define PCIX_MISC_BRIDGE_ERRORS_OFFSET 0x80
int segment; /* PCI domain */
u8 bus; /* PCI bus number */
u8 devfn; /* PCI devfn number */
- struct pci_dev *dev; /* it's NULL for PCIE-to-PCI bridge */
+ struct pci_dev *dev; /* it's NULL for PCIe-to-PCI bridge */
struct intel_iommu *iommu; /* IOMMU used by this device */
struct dmar_domain *domain; /* pointer to domain */
};
return ret;
parent = parent->bus->self;
}
- if (pci_is_pcie(tmp)) /* this is a PCIE-to-PCI bridge */
+ if (pci_is_pcie(tmp)) /* this is a PCIe-to-PCI bridge */
return domain_context_mapping_one(domain,
pci_domain_nr(tmp->subordinate),
tmp->subordinate->number, 0,
parent->devfn);
parent = parent->bus->self;
}
- if (pci_is_pcie(tmp)) /* this is a PCIE-to-PCI bridge */
+ if (pci_is_pcie(tmp)) /* this is a PCIe-to-PCI bridge */
iommu_detach_dev(iommu,
tmp->subordinate->number, 0);
else /* this is a legacy PCI bridge */
bridge = pci_find_upstream_pcie_bridge(dev);
if (bridge) {
- if (pci_is_pcie(bridge))/* this is a PCIE-to-PCI/PCIX bridge */
+ if (pci_is_pcie(bridge))/* this is a PCIe-to-PCI/PCIX bridge */
set_irte_sid(irte, SVT_VERIFY_BUS, SQ_ALL_16,
(bridge->bus->number << 8) | dev->bus->number);
else /* this is a legacy PCI bridge */
static void acpi_pci_propagate_wakeup_enable(struct pci_bus *bus, bool enable)
{
while (bus->parent) {
- struct pci_dev *bridge = bus->self;
- int ret;
-
- ret = acpi_pm_device_sleep_wake(&bridge->dev, enable);
- if (!ret || pci_is_pcie(bridge))
+ if (!acpi_pm_device_sleep_wake(&bus->self->dev, enable))
return;
bus = bus->parent;
}
if (acpi_pci_can_wakeup(dev))
return acpi_pm_device_sleep_wake(&dev->dev, enable);
- if (!pci_is_pcie(dev))
- acpi_pci_propagate_wakeup_enable(dev->bus, enable);
-
+ acpi_pci_propagate_wakeup_enable(dev->bus, enable);
return 0;
}
/**
* pcibios_set_pcie_reset_state - set reset state for device dev
- * @dev: the PCI-E device reset
+ * @dev: the PCIe device reset
* @state: Reset state to enter into
*
*
- * Sets the PCI-E reset state for the device. This is the default
+ * Sets the PCIe reset state for the device. This is the default
* implementation. Architecture implementations can override this.
*/
int __attribute__ ((weak)) pcibios_set_pcie_reset_state(struct pci_dev *dev,
/**
* pci_set_pcie_reset_state - set reset state for device dev
- * @dev: the PCI-E device reset
+ * @dev: the PCIe device reset
* @state: Reset state to enter into
*
*
down(&dev->dev.sem);
}
+ rc = pci_dev_specific_reset(dev, probe);
+ if (rc != -ENOTTY)
+ goto done;
+
rc = pcie_flr(dev, probe);
if (rc != -ENOTTY)
goto done;
return 1;
}
+void __weak pci_fixup_cardbus(struct pci_bus *bus)
+{
+}
+EXPORT_SYMBOL(pci_fixup_cardbus);
+
static int __init pci_setup(char *str)
{
while (str) {
extern void pci_enable_acs(struct pci_dev *dev);
+struct pci_dev_reset_methods {
+ u16 vendor;
+ u16 device;
+ int (*reset)(struct pci_dev *dev, int probe);
+};
+
+extern int pci_dev_specific_reset(struct pci_dev *dev, int probe);
+
#endif /* DRIVERS_PCI_H */
#
config PCIEAER_INJECT
- tristate "PCIE AER error injector support"
+ tristate "PCIe AER error injector support"
depends on PCIEAER
default n
help
This enables PCI Express Root Port Advanced Error Reporting
(AER) software error injector.
- Debuging PCIE AER code is quite difficult because it is hard
+ Debugging PCIe AER code is quite difficult because it is hard
to trigger various real hardware errors. Software based
error injection can fake almost all kinds of errors with the
help of a user space helper tool aer-inject, which can be
/*
- * PCIE AER software error injection support.
+ * PCIe AER software error injection support.
*
- * Debuging PCIE AER code is quite difficult because it is hard to
+ * Debuging PCIe AER code is quite difficult because it is hard to
* trigger various real hardware errors. Software based error
* injection can fake almost all kinds of errors with the help of a
* user space helper tool aer-inject, which can be gotten from:
module_init(aer_inject_init);
module_exit(aer_inject_exit);
-MODULE_DESCRIPTION("PCIE AER software error injector");
+MODULE_DESCRIPTION("PCIe AER software error injector");
MODULE_LICENSE("GPL");
mutex_init(&rpc->rpc_mutex);
init_waitqueue_head(&rpc->wait_release);
- /* Use PCIE bus function to store rpc into PCIE device */
+ /* Use PCIe bus function to store rpc into PCIe device */
set_service_data(dev, rpc);
return rpc;
*
* @return: Zero on success. Nonzero otherwise.
*
- * Invoked when PCIE bus loads AER service driver. To avoid conflict with
+ * Invoked when PCIe bus loads AER service driver. To avoid conflict with
* BIOS AER support requires BIOS to yield AER control to OS native driver.
**/
int aer_osc_setup(struct pcie_device *pciedev)
* aer_enable_rootport - enable Root Port's interrupts when receiving messages
* @rpc: pointer to a Root Port data structure
*
- * Invoked when PCIE bus loads AER service driver.
+ * Invoked when PCIe bus loads AER service driver.
*/
void aer_enable_rootport(struct aer_rpc *rpc)
{
u32 reg32;
pos = pci_pcie_cap(pdev);
- /* Clear PCIE Capability's Device Status */
+ /* Clear PCIe Capability's Device Status */
pci_read_config_word(pdev, pos+PCI_EXP_DEVSTA, ®16);
pci_write_config_word(pdev, pos+PCI_EXP_DEVSTA, reg16);
* disable_root_aer - disable Root Port's interrupts when receiving messages
* @rpc: pointer to a Root Port data structure
*
- * Invoked when PCIE bus unloads AER service driver.
+ * Invoked when PCIe bus unloads AER service driver.
*/
static void disable_root_aer(struct aer_rpc *rpc)
{
if (info->status == 0) {
AER_PR(info, dev,
- "PCIE Bus Error: severity=%s, type=Unaccessible, "
+ "PCIe Bus Error: severity=%s, type=Unaccessible, "
"id=%04x(Unregistered Agent ID)\n",
aer_error_severity_string[info->severity], id);
} else {
agent = AER_GET_AGENT(info->severity, info->status);
AER_PR(info, dev,
- "PCIE Bus Error: severity=%s, type=%s, id=%04x(%s)\n",
+ "PCIe Bus Error: severity=%s, type=%s, id=%04x(%s)\n",
aer_error_severity_string[info->severity],
aer_error_layer[layer], id, aer_agent_string[agent]);
/*
* File: drivers/pci/pcie/aspm.c
- * Enabling PCIE link L0s/L1 state and Clock Power Management
+ * Enabling PCIe link L0s/L1 state and Clock Power Management
*
* Copyright (C) 2007 Intel
* Copyright (C) Zhang Yanmin (yanmin.zhang@intel.com)
int pos;
u32 reg32;
/*
- * Some functions in a slot might not all be PCIE functions,
+ * Some functions in a slot might not all be PCIe functions,
* very strange. Disable ASPM for the whole slot
*/
list_for_each_entry(child, &pdev->subordinate->devices, bus_list) {
*/
#define DRIVER_VERSION "v1.0"
#define DRIVER_AUTHOR "tom.l.nguyen@intel.com"
-#define DRIVER_DESC "PCIE Port Bus Driver"
+#define DRIVER_DESC "PCIe Port Bus Driver"
MODULE_AUTHOR(DRIVER_AUTHOR);
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");
if (!pci_cache_line_size) {
printk(KERN_DEBUG "PCI: CLS %u bytes, default %u\n",
cls << 2, pci_dfl_cache_line_size << 2);
- pci_cache_line_size = cls;
+ pci_cache_line_size = cls ? cls : pci_dfl_cache_line_size;
}
return 0;
}
fs_initcall_sync(pci_apply_final_quirks);
+
+/*
+ * Followings are device-specific reset methods which can be used to
+ * reset a single function if other methods (e.g. FLR, PM D0->D3) are
+ * not available.
+ */
+static int reset_intel_generic_dev(struct pci_dev *dev, int probe)
+{
+ int pos;
+
+ /* only implement PCI_CLASS_SERIAL_USB at present */
+ if (dev->class == PCI_CLASS_SERIAL_USB) {
+ pos = pci_find_capability(dev, PCI_CAP_ID_VNDR);
+ if (!pos)
+ return -ENOTTY;
+
+ if (probe)
+ return 0;
+
+ pci_write_config_byte(dev, pos + 0x4, 1);
+ msleep(100);
+
+ return 0;
+ } else {
+ return -ENOTTY;
+ }
+}
+
+static int reset_intel_82599_sfp_virtfn(struct pci_dev *dev, int probe)
+{
+ int pos;
+
+ pos = pci_find_capability(dev, PCI_CAP_ID_EXP);
+ if (!pos)
+ return -ENOTTY;
+
+ if (probe)
+ return 0;
+
+ pci_write_config_word(dev, pos + PCI_EXP_DEVCTL,
+ PCI_EXP_DEVCTL_BCR_FLR);
+ msleep(100);
+
+ return 0;
+}
+
+#define PCI_DEVICE_ID_INTEL_82599_SFP_VF 0x10ed
+
+static const struct pci_dev_reset_methods pci_dev_reset_methods[] = {
+ { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF,
+ reset_intel_82599_sfp_virtfn },
+ { PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
+ reset_intel_generic_dev },
+ { 0 }
+};
+
+int pci_dev_specific_reset(struct pci_dev *dev, int probe)
+{
+ const struct pci_dev_reset_methods *i;
+
+ for (i = pci_dev_reset_methods; i->reset; i++) {
+ if ((i->vendor == dev->vendor ||
+ i->vendor == (u16)PCI_ANY_ID) &&
+ (i->device == dev->device ||
+ i->device == (u16)PCI_ANY_ID))
+ return i->reset(dev, probe);
+ }
+
+ return -ENOTTY;
+}
+
#else
void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) {}
+int pci_dev_specific_reset(struct pci_dev *dev, int probe) { return -ENOTTY; }
#endif
EXPORT_SYMBOL(pci_fixup_device);
DECLARE_RWSEM(pci_bus_sem);
/*
- * find the upstream PCIE-to-PCI bridge of a PCI device
+ * find the upstream PCIe-to-PCI bridge of a PCI device
* if the device is PCIE, return NULL
- * if the device isn't connected to a PCIE bridge (that is its parent is a
+ * if the device isn't connected to a PCIe bridge (that is its parent is a
* legacy PCI bridge and the bridge is directly connected to bus 0), return its
* parent
*/
tmp = pdev;
continue;
}
- /* PCI device should connect to a PCIE bridge */
+ /* PCI device should connect to a PCIe bridge */
if (pdev->pcie_type != PCI_EXP_TYPE_PCI_BRIDGE) {
/* Busted hardware? */
WARN_ON_ONCE(1);
unsigned int max, pass;
s->functions = pci_scan_slot(bus, PCI_DEVFN(0, 0));
-/* pcibios_fixup_bus(bus); */
+ pci_fixup_cardbus(bus);
max = bus->secondary;
for (pass = 0; pass < 2; pass++)
This driver was formerly known as ibm-acpi.
+ Extra functionality will be available if the rfkill (CONFIG_RFKILL)
+ and/or ALSA (CONFIG_SND) subsystems are available in the kernel.
+ Note that if you want ThinkPad-ACPI to be built-in instead of
+ modular, ALSA and rfkill will also have to be built-in.
+
If you have an IBM or Lenovo ThinkPad laptop, say Y or M here.
+config THINKPAD_ACPI_ALSA_SUPPORT
+ bool "Console audio control ALSA interface"
+ depends on THINKPAD_ACPI
+ depends on SND
+ depends on SND = y || THINKPAD_ACPI = SND
+ default y
+ ---help---
+ Enables monitoring of the built-in console audio output control
+ (headphone and speakers), which is operated by the mute and (in
+ some ThinkPad models) volume hotkeys.
+
+ If this option is enabled, ThinkPad-ACPI will export an ALSA card
+ with a single read-only mixer control, which should be used for
+ on-screen-display feedback purposes by the Desktop Environment.
+
+ Optionally, the driver will also allow software control (the
+ ALSA mixer will be made read-write). Please refer to the driver
+ documentation for details.
+
+ All IBM models have both volume and mute control. Newer Lenovo
+ models only have mute control (the volume hotkeys are just normal
+ keys and volume control is done through the main HDA mixer).
+
config THINKPAD_ACPI_DEBUGFACILITIES
bool "Maintainer debug facilities"
depends on THINKPAD_ACPI
struct acpi_buffer response = { ACPI_ALLOCATE_BUFFER, NULL };
static struct key_entry *key;
union acpi_object *obj;
+ acpi_status status;
- wmi_get_event_data(value, &response);
+ status = wmi_get_event_data(value, &response);
+ if (status != AE_OK) {
+ printk(KERN_INFO "dell-wmi: bad event status 0x%x\n", status);
+ return;
+ }
obj = (union acpi_object *)response.pointer;
static int __init dell_wmi_init(void)
{
int err;
+ acpi_status status;
- if (wmi_has_guid(DELL_EVENT_GUID)) {
+ if (!wmi_has_guid(DELL_EVENT_GUID)) {
printk(KERN_WARNING "dell-wmi: No known WMI GUID found\n");
return -ENODEV;
}
if (err)
return err;
- err = wmi_install_notify_handler(DELL_EVENT_GUID,
+ status = wmi_install_notify_handler(DELL_EVENT_GUID,
dell_wmi_notify, NULL);
- if (err) {
+ if (ACPI_FAILURE(status)) {
input_unregister_device(dell_wmi_input_dev);
printk(KERN_ERR
"dell-wmi: Unable to register notify handler - %d\n",
- err);
- return err;
+ status);
+ return -ENODEV;
}
return 0;
static struct key_entry *key;
union acpi_object *obj;
int eventcode;
+ acpi_status status;
- wmi_get_event_data(value, &response);
+ status = wmi_get_event_data(value, &response);
+ if (status != AE_OK) {
+ printk(KERN_INFO "hp-wmi: bad event status 0x%x\n", status);
+ return;
+ }
obj = (union acpi_object *)response.pointer;
if (wmi_has_guid(HPWMI_EVENT_GUID)) {
err = wmi_install_notify_handler(HPWMI_EVENT_GUID,
hp_wmi_notify, NULL);
- if (!err)
+ if (ACPI_SUCCESS(err))
hp_wmi_input_setup();
}
static struct key_entry *key;
union acpi_object *obj;
ktime_t cur;
+ acpi_status status;
- wmi_get_event_data(value, &response);
+ status = wmi_get_event_data(value, &response);
+ if (status != AE_OK) {
+ printk(KERN_INFO DRV_PFX "bad event status 0x%x\n", status);
+ return;
+ }
obj = (union acpi_object *)response.pointer;
}
err = wmi_install_notify_handler(MSIWMI_EVENT_GUID,
msi_wmi_notify, NULL);
- if (err)
+ if (ACPI_FAILURE(err))
return -EINVAL;
err = msi_wmi_input_setup();
* and we leave them unchanged.
*/
+#ifdef CONFIG_THINKPAD_ACPI_ALSA_SUPPORT
+
#define TPACPI_ALSA_DRVNAME "ThinkPad EC"
#define TPACPI_ALSA_SHRTNAME "ThinkPad Console Audio Control"
#define TPACPI_ALSA_MIXERNAME TPACPI_ALSA_SHRTNAME
-static int alsa_index = SNDRV_DEFAULT_IDX1;
+static int alsa_index = ~((1 << (SNDRV_CARDS - 3)) - 1); /* last three slots */
static char *alsa_id = "ThinkPadEC";
static int alsa_enable = SNDRV_DEFAULT_ENABLE1;
rc = snd_card_create(alsa_index, alsa_id, THIS_MODULE,
sizeof(struct tpacpi_alsa_data), &card);
- if (rc < 0)
- return rc;
- if (!card)
- return -ENOMEM;
+ if (rc < 0 || !card) {
+ printk(TPACPI_ERR
+ "Failed to create ALSA card structures: %d\n", rc);
+ return 1;
+ }
BUG_ON(!card->private_data);
data = card->private_data;
rc = snd_ctl_add(card, ctl_vol);
if (rc < 0) {
printk(TPACPI_ERR
- "Failed to create ALSA volume control\n");
- goto err_out;
+ "Failed to create ALSA volume control: %d\n",
+ rc);
+ goto err_exit;
}
data->ctl_vol_id = &ctl_vol->id;
}
ctl_mute = snd_ctl_new1(&volume_alsa_control_mute, NULL);
rc = snd_ctl_add(card, ctl_mute);
if (rc < 0) {
- printk(TPACPI_ERR "Failed to create ALSA mute control\n");
- goto err_out;
+ printk(TPACPI_ERR "Failed to create ALSA mute control: %d\n",
+ rc);
+ goto err_exit;
}
data->ctl_mute_id = &ctl_mute->id;
snd_card_set_dev(card, &tpacpi_pdev->dev);
rc = snd_card_register(card);
-
-err_out:
if (rc < 0) {
- snd_card_free(card);
- card = NULL;
+ printk(TPACPI_ERR "Failed to register ALSA card: %d\n", rc);
+ goto err_exit;
}
alsa_card = card;
- return rc;
+ return 0;
+
+err_exit:
+ snd_card_free(card);
+ return 1;
}
#define TPACPI_VOL_Q_MUTEONLY 0x0001 /* Mute-only control available */
.shutdown = volume_shutdown,
};
+#else /* !CONFIG_THINKPAD_ACPI_ALSA_SUPPORT */
+
+#define alsa_card NULL
+
+static void inline volume_alsa_notify_change(void)
+{
+}
+
+static int __init volume_init(struct ibm_init_struct *iibm)
+{
+ printk(TPACPI_INFO
+ "volume: disabled as there is no ALSA support in this kernel\n");
+
+ return 1;
+}
+
+static struct ibm_struct volume_driver_data = {
+ .name = "volume",
+};
+
+#endif /* CONFIG_THINKPAD_ACPI_ALSA_SUPPORT */
+
/*************************************************************************
* Fan subdriver
*/
"used for backwards compatibility with userspace, "
"see documentation");
+#ifdef CONFIG_THINKPAD_ACPI_ALSA_SUPPORT
module_param_named(volume_mode, volume_mode, uint, 0444);
MODULE_PARM_DESC(volume_mode,
"Selects volume control strategy: "
MODULE_PARM_DESC(id, "ALSA id for the ACPI EC Mixer");
module_param_named(enable, alsa_enable, bool, 0444);
MODULE_PARM_DESC(enable, "Enable the ALSA interface for the ACPI EC Mixer");
+#endif /* CONFIG_THINKPAD_ACPI_ALSA_SUPPORT */
#define TPACPI_PARAM(feature) \
module_param_call(feature, set_ibm_param, NULL, NULL, 0); \
if (!guid || !handler)
return AE_BAD_PARAMETER;
- find_guid(guid, &block);
- if (!block)
+ if (!find_guid(guid, &block))
return AE_NOT_EXIST;
if (block->handler)
if (!guid)
return AE_BAD_PARAMETER;
- find_guid(guid, &block);
- if (!block)
+ if (!find_guid(guid, &block))
return AE_NOT_EXIST;
if (!block->handler)
return ret;
}
+static bool guid_already_parsed(const char *guid_string)
+{
+ struct guid_block *gblock;
+ struct wmi_block *wblock;
+ struct list_head *p;
+
+ list_for_each(p, &wmi_blocks.list) {
+ wblock = list_entry(p, struct wmi_block, list);
+ gblock = &wblock->gblock;
+
+ if (strncmp(gblock->guid, guid_string, 16) == 0)
+ return true;
+ }
+ return false;
+}
+
/*
* Parse the _WDG method for the GUID data blocks
*/
union acpi_object *obj;
struct guid_block *gblock;
struct wmi_block *wblock;
+ char guid_string[37];
acpi_status status;
u32 i, total;
memcpy(gblock, obj->buffer.pointer, obj->buffer.length);
for (i = 0; i < total; i++) {
+ /*
+ Some WMI devices, like those for nVidia hooks, have a
+ duplicate GUID. It's not clear what we should do in this
+ case yet, so for now, we'll just ignore the duplicate.
+ Anyone who wants to add support for that device can come
+ up with a better workaround for the mess then.
+ */
+ if (guid_already_parsed(gblock[i].guid) == true) {
+ wmi_gtoa(gblock[i].guid, guid_string);
+ printk(KERN_INFO PREFIX "Skipping duplicate GUID %s\n",
+ guid_string);
+ continue;
+ }
wblock = kzalloc(sizeof(struct wmi_block), GFP_KERNEL);
if (!wblock)
return AE_NO_MEMORY;
mounting to OS/400 Netserve. Fix oops in cifs_get_tcp_session.
Disable use of server inode numbers when server only
partially supports them (e.g. for one server querying inode numbers on
-FindFirst fails but QPathInfo queries works).
+FindFirst fails but QPathInfo queries works). Fix oops with dfs in
+cifs_put_smb_ses. Fix mmap to work on directio mounts (needed
+for OpenOffice when on forcedirectio mount e.g.)
Version 1.60
-------------
};
const struct file_operations cifs_file_direct_ops = {
- /* no mmap, no aio, no readv -
+ /* no aio, no readv -
BB reevaluate whether they can be done with directio, no cache */
.read = cifs_user_read,
.write = cifs_user_write,
.lock = cifs_lock,
.fsync = cifs_fsync,
.flush = cifs_flush,
+ .mmap = cifs_file_mmap,
.splice_read = generic_file_splice_read,
#ifdef CONFIG_CIFS_POSIX
.unlocked_ioctl = cifs_ioctl,
cifs_mount(struct super_block *sb, struct cifs_sb_info *cifs_sb,
char *mount_data_global, const char *devname)
{
- int rc = 0;
+ int rc;
int xid;
struct smb_vol *volume_info;
- struct cifsSesInfo *pSesInfo = NULL;
- struct cifsTconInfo *tcon = NULL;
- struct TCP_Server_Info *srvTcp = NULL;
+ struct cifsSesInfo *pSesInfo;
+ struct cifsTconInfo *tcon;
+ struct TCP_Server_Info *srvTcp;
char *full_path;
char *mount_data = mount_data_global;
#ifdef CONFIG_CIFS_DFS_UPCALL
int referral_walks_count = 0;
try_mount_again:
#endif
+ rc = 0;
+ tcon = NULL;
+ pSesInfo = NULL;
+ srvTcp = NULL;
full_path = NULL;
xid = GetXid();
cleanup_volume_info(&volume_info);
referral_walks_count++;
+ FreeXid(xid);
goto try_mount_again;
}
#else /* No DFS support, return error on mount */
config EXT4_USE_FOR_EXT23
bool "Use ext4 for ext2/ext3 file systems"
+ depends on EXT4_FS
depends on EXT3_FS=n || EXT2_FS=n
default y
help
#include <linux/module.h>
#include <linux/swap.h>
#include <linux/pagemap.h>
-#include <linux/version.h>
#include <linux/blkdev.h>
#include <linux/mutex.h>
#include "ext4.h"
return err;
}
+static void unmap_underlying_metadata_blocks(struct block_device *bdev,
+ sector_t block, int count)
+{
+ int i;
+ for (i = 0; i < count; i++)
+ unmap_underlying_metadata(bdev, block + i);
+}
+
static int
ext4_ext_handle_uninitialized_extents(handle_t *handle, struct inode *inode,
ext4_lblk_t iblock, unsigned int max_blocks,
} else
allocated = ret;
set_buffer_new(bh_result);
+ /*
+ * if we allocated more blocks than requested
+ * we need to make sure we unmap the extra block
+ * allocated. The actual needed block will get
+ * unmapped later when we find the buffer_head marked
+ * new.
+ */
+ if (allocated > max_blocks) {
+ unmap_underlying_metadata_blocks(inode->i_sb->s_bdev,
+ newblock + max_blocks,
+ allocated - max_blocks);
+ }
map_out:
set_buffer_mapped(bh_result);
out1:
* this situation is possible, though, _during_ tree modification;
* this is why assert can't be put in ext4_ext_find_extent()
*/
- BUG_ON(path[depth].p_ext == NULL && depth != 0);
+ if (path[depth].p_ext == NULL && depth != 0) {
+ ext4_error(inode->i_sb, __func__, "bad extent address "
+ "inode: %lu, iblock: %d, depth: %d",
+ inode->i_ino, iblock, depth);
+ err = -EIO;
+ goto out2;
+ }
eh = path[depth].p_hdr;
ex = path[depth].p_ext;
return ext4_force_commit(inode->i_sb);
commit_tid = datasync ? ei->i_datasync_tid : ei->i_sync_tid;
- if (jbd2_log_start_commit(journal, commit_tid))
+ if (jbd2_log_start_commit(journal, commit_tid)) {
+ /*
+ * When the journal is on a different device than the
+ * fs data disk, we need to issue the barrier in
+ * writeback mode. (In ordered mode, the jbd2 layer
+ * will take care of issuing the barrier. In
+ * data=journal, all of the data blocks are written to
+ * the journal device.)
+ */
+ if (ext4_should_writeback_data(inode) &&
+ (journal->j_fs_dev != journal->j_dev) &&
+ (journal->j_flags & JBD2_BARRIER))
+ blkdev_issue_flush(inode->i_sb->s_bdev, NULL);
jbd2_log_wait_commit(journal, commit_tid);
- else if (journal->j_flags & JBD2_BARRIER)
+ } else if (journal->j_flags & JBD2_BARRIER)
blkdev_issue_flush(inode->i_sb->s_bdev, NULL);
return ret;
}
return ext4_indirect_calc_metadata_amount(inode, blocks);
}
+/*
+ * Called with i_data_sem down, which is important since we can call
+ * ext4_discard_preallocations() from here.
+ */
static void ext4_da_update_reserve_space(struct inode *inode, int used)
{
struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
- int total, mdb, mdb_free, mdb_claim = 0;
-
- spin_lock(&EXT4_I(inode)->i_block_reservation_lock);
- /* recalculate the number of metablocks still need to be reserved */
- total = EXT4_I(inode)->i_reserved_data_blocks - used;
- mdb = ext4_calc_metadata_amount(inode, total);
-
- /* figure out how many metablocks to release */
- BUG_ON(mdb > EXT4_I(inode)->i_reserved_meta_blocks);
- mdb_free = EXT4_I(inode)->i_reserved_meta_blocks - mdb;
-
- if (mdb_free) {
- /* Account for allocated meta_blocks */
- mdb_claim = EXT4_I(inode)->i_allocated_meta_blocks;
- BUG_ON(mdb_free < mdb_claim);
- mdb_free -= mdb_claim;
-
- /* update fs dirty blocks counter */
+ struct ext4_inode_info *ei = EXT4_I(inode);
+ int mdb_free = 0;
+
+ spin_lock(&ei->i_block_reservation_lock);
+ if (unlikely(used > ei->i_reserved_data_blocks)) {
+ ext4_msg(inode->i_sb, KERN_NOTICE, "%s: ino %lu, used %d "
+ "with only %d reserved data blocks\n",
+ __func__, inode->i_ino, used,
+ ei->i_reserved_data_blocks);
+ WARN_ON(1);
+ used = ei->i_reserved_data_blocks;
+ }
+
+ /* Update per-inode reservations */
+ ei->i_reserved_data_blocks -= used;
+ used += ei->i_allocated_meta_blocks;
+ ei->i_reserved_meta_blocks -= ei->i_allocated_meta_blocks;
+ ei->i_allocated_meta_blocks = 0;
+ percpu_counter_sub(&sbi->s_dirtyblocks_counter, used);
+
+ if (ei->i_reserved_data_blocks == 0) {
+ /*
+ * We can release all of the reserved metadata blocks
+ * only when we have written all of the delayed
+ * allocation blocks.
+ */
+ mdb_free = ei->i_allocated_meta_blocks;
percpu_counter_sub(&sbi->s_dirtyblocks_counter, mdb_free);
- EXT4_I(inode)->i_allocated_meta_blocks = 0;
- EXT4_I(inode)->i_reserved_meta_blocks = mdb;
+ ei->i_allocated_meta_blocks = 0;
}
-
- /* update per-inode reservations */
- BUG_ON(used > EXT4_I(inode)->i_reserved_data_blocks);
- EXT4_I(inode)->i_reserved_data_blocks -= used;
- percpu_counter_sub(&sbi->s_dirtyblocks_counter, used + mdb_claim);
spin_unlock(&EXT4_I(inode)->i_block_reservation_lock);
- vfs_dq_claim_block(inode, used + mdb_claim);
-
- /*
- * free those over-booking quota for metadata blocks
- */
+ /* Update quota subsystem */
+ vfs_dq_claim_block(inode, used);
if (mdb_free)
vfs_dq_release_reservation_block(inode, mdb_free);
* there aren't any writers on the inode, we can discard the
* inode's preallocations.
*/
- if (!total && (atomic_read(&inode->i_writecount) == 0))
+ if ((ei->i_reserved_data_blocks == 0) &&
+ (atomic_read(&inode->i_writecount) == 0))
ext4_discard_preallocations(inode);
}
{
int retries = 0;
struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
- unsigned long md_needed, mdblocks, total = 0;
+ struct ext4_inode_info *ei = EXT4_I(inode);
+ unsigned long md_needed, md_reserved, total = 0;
/*
* recalculate the amount of metadata blocks to reserve
* worse case is one extent per block
*/
repeat:
- spin_lock(&EXT4_I(inode)->i_block_reservation_lock);
- total = EXT4_I(inode)->i_reserved_data_blocks + nrblocks;
- mdblocks = ext4_calc_metadata_amount(inode, total);
- BUG_ON(mdblocks < EXT4_I(inode)->i_reserved_meta_blocks);
-
- md_needed = mdblocks - EXT4_I(inode)->i_reserved_meta_blocks;
+ spin_lock(&ei->i_block_reservation_lock);
+ md_reserved = ei->i_reserved_meta_blocks;
+ md_needed = ext4_calc_metadata_amount(inode, nrblocks);
total = md_needed + nrblocks;
- spin_unlock(&EXT4_I(inode)->i_block_reservation_lock);
+ spin_unlock(&ei->i_block_reservation_lock);
/*
* Make quota reservation here to prevent quota overflow
* later. Real quota accounting is done at pages writeout
* time.
*/
- if (vfs_dq_reserve_block(inode, total))
+ if (vfs_dq_reserve_block(inode, total)) {
+ /*
+ * We tend to badly over-estimate the amount of
+ * metadata blocks which are needed, so if we have
+ * reserved any metadata blocks, try to force out the
+ * inode and see if we have any better luck.
+ */
+ if (md_reserved && retries++ <= 3)
+ goto retry;
return -EDQUOT;
+ }
if (ext4_claim_free_blocks(sbi, total)) {
vfs_dq_release_reservation_block(inode, total);
if (ext4_should_retry_alloc(inode->i_sb, &retries)) {
+ retry:
+ if (md_reserved)
+ write_inode_now(inode, (retries == 3));
yield();
goto repeat;
}
return -ENOSPC;
}
- spin_lock(&EXT4_I(inode)->i_block_reservation_lock);
- EXT4_I(inode)->i_reserved_data_blocks += nrblocks;
- EXT4_I(inode)->i_reserved_meta_blocks += md_needed;
- spin_unlock(&EXT4_I(inode)->i_block_reservation_lock);
+ spin_lock(&ei->i_block_reservation_lock);
+ ei->i_reserved_data_blocks += nrblocks;
+ ei->i_reserved_meta_blocks += md_needed;
+ spin_unlock(&ei->i_block_reservation_lock);
return 0; /* success */
}
static void ext4_da_release_space(struct inode *inode, int to_free)
{
struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
- int total, mdb, mdb_free, release;
+ struct ext4_inode_info *ei = EXT4_I(inode);
if (!to_free)
return; /* Nothing to release, exit */
spin_lock(&EXT4_I(inode)->i_block_reservation_lock);
- if (!EXT4_I(inode)->i_reserved_data_blocks) {
+ if (unlikely(to_free > ei->i_reserved_data_blocks)) {
/*
- * if there is no reserved blocks, but we try to free some
- * then the counter is messed up somewhere.
- * but since this function is called from invalidate
- * page, it's harmless to return without any action
+ * if there aren't enough reserved blocks, then the
+ * counter is messed up somewhere. Since this
+ * function is called from invalidate page, it's
+ * harmless to return without any action.
*/
- printk(KERN_INFO "ext4 delalloc try to release %d reserved "
- "blocks for inode %lu, but there is no reserved "
- "data blocks\n", to_free, inode->i_ino);
- spin_unlock(&EXT4_I(inode)->i_block_reservation_lock);
- return;
+ ext4_msg(inode->i_sb, KERN_NOTICE, "ext4_da_release_space: "
+ "ino %lu, to_free %d with only %d reserved "
+ "data blocks\n", inode->i_ino, to_free,
+ ei->i_reserved_data_blocks);
+ WARN_ON(1);
+ to_free = ei->i_reserved_data_blocks;
}
+ ei->i_reserved_data_blocks -= to_free;
- /* recalculate the number of metablocks still need to be reserved */
- total = EXT4_I(inode)->i_reserved_data_blocks - to_free;
- mdb = ext4_calc_metadata_amount(inode, total);
-
- /* figure out how many metablocks to release */
- BUG_ON(mdb > EXT4_I(inode)->i_reserved_meta_blocks);
- mdb_free = EXT4_I(inode)->i_reserved_meta_blocks - mdb;
-
- release = to_free + mdb_free;
-
- /* update fs dirty blocks counter for truncate case */
- percpu_counter_sub(&sbi->s_dirtyblocks_counter, release);
+ if (ei->i_reserved_data_blocks == 0) {
+ /*
+ * We can release all of the reserved metadata blocks
+ * only when we have written all of the delayed
+ * allocation blocks.
+ */
+ to_free += ei->i_allocated_meta_blocks;
+ ei->i_allocated_meta_blocks = 0;
+ }
- /* update per-inode reservations */
- BUG_ON(to_free > EXT4_I(inode)->i_reserved_data_blocks);
- EXT4_I(inode)->i_reserved_data_blocks -= to_free;
+ /* update fs dirty blocks counter */
+ percpu_counter_sub(&sbi->s_dirtyblocks_counter, to_free);
- BUG_ON(mdb > EXT4_I(inode)->i_reserved_meta_blocks);
- EXT4_I(inode)->i_reserved_meta_blocks = mdb;
spin_unlock(&EXT4_I(inode)->i_block_reservation_lock);
- vfs_dq_release_reservation_block(inode, release);
+ vfs_dq_release_reservation_block(inode, to_free);
}
static void ext4_da_page_release_reservation(struct page *page,
out_writepages:
if (!no_nrwrite_index_update)
wbc->no_nrwrite_index_update = 0;
- if (wbc->nr_to_write > nr_to_writebump)
- wbc->nr_to_write -= nr_to_writebump;
+ wbc->nr_to_write -= nr_to_writebump;
wbc->range_start = range_start;
trace_ext4_da_writepages_result(inode, wbc, ret, pages_written);
return ret;
if (2 * free_blocks < 3 * dirty_blocks ||
free_blocks < (dirty_blocks + EXT4_FREEBLOCKS_WATERMARK)) {
/*
- * free block count is less that 150% of dirty blocks
- * or free blocks is less that watermark
+ * free block count is less than 150% of dirty blocks
+ * or free blocks is less than watermark
*/
return 1;
}
+ /*
+ * Even if we don't switch but are nearing capacity,
+ * start pushing delalloc when 1/2 of free blocks are dirty.
+ */
+ if (free_blocks < 2 * dirty_blocks)
+ writeback_inodes_sb_if_idle(sb);
+
return 0;
}
#include <linux/proc_fs.h>
#include <linux/pagemap.h>
#include <linux/seq_file.h>
-#include <linux/version.h>
#include <linux/blkdev.h>
#include <linux/mutex.h>
#include "ext4_jbd2.h"
struct super_block *sb = sbi->s_buddy_cache->i_sb;
return snprintf(buf, PAGE_SIZE, "%llu\n",
- sbi->s_kbytes_written +
+ (unsigned long long)(sbi->s_kbytes_written +
((part_stat_read(sb->s_bdev->bd_part, sectors[1]) -
- EXT4_SB(sb)->s_sectors_written_start) >> 1));
+ EXT4_SB(sb)->s_sectors_written_start) >> 1)));
}
static ssize_t inode_readahead_blks_store(struct ext4_attr *a,
{
unregister_filesystem(&ext2_fs_type);
}
+MODULE_ALIAS("ext2");
#else
static inline void register_as_ext2(void) { }
static inline void unregister_as_ext2(void) { }
{
unregister_filesystem(&ext3_fs_type);
}
+MODULE_ALIAS("ext3");
#else
static inline void register_as_ext3(void) { }
static inline void unregister_as_ext3(void) { }
goto cleanup;
kfree(b_entry_name);
kfree(buffer);
+ b_entry_name = NULL;
+ buffer = NULL;
brelse(is->iloc.bh);
kfree(is);
kfree(bs);
/**
* bdi_start_writeback - start writeback
* @bdi: the backing device to write from
+ * @sb: write inodes from this super_block
* @nr_pages: the number of pages to write
*
* Description:
}
EXPORT_SYMBOL(writeback_inodes_sb);
+/**
+ * writeback_inodes_sb_if_idle - start writeback if none underway
+ * @sb: the superblock
+ *
+ * Invoke writeback_inodes_sb if no writeback is currently underway.
+ * Returns 1 if writeback was started, 0 if not.
+ */
+int writeback_inodes_sb_if_idle(struct super_block *sb)
+{
+ if (!writeback_in_progress(sb->s_bdi)) {
+ writeback_inodes_sb(sb);
+ return 1;
+ } else
+ return 0;
+}
+EXPORT_SYMBOL(writeback_inodes_sb_if_idle);
+
/**
* sync_inodes_sb - sync sb inode pages
* @sb: the superblock
#include <linux/jbd2.h>
#include <linux/errno.h>
#include <linux/slab.h>
+#include <linux/blkdev.h>
#include <trace/events/jbd2.h>
/*
journal->j_tail_sequence = first_tid;
journal->j_tail = blocknr;
spin_unlock(&journal->j_state_lock);
+
+ /*
+ * If there is an external journal, we need to make sure that
+ * any data blocks that were recently written out --- perhaps
+ * by jbd2_log_do_checkpoint() --- are flushed out before we
+ * drop the transactions from the external journal. It's
+ * unlikely this will be necessary, especially with a
+ * appropriately sized journal, but we need this to guarantee
+ * correctness. Fortunately jbd2_cleanup_journal_tail()
+ * doesn't get called all that often.
+ */
+ if ((journal->j_fs_dev != journal->j_dev) &&
+ (journal->j_flags & JBD2_BARRIER))
+ blkdev_issue_flush(journal->j_fs_dev, NULL);
if (!(journal->j_flags & JBD2_ABORT))
jbd2_journal_update_superblock(journal, 1);
return 0;
ret = err;
spin_lock(&journal->j_list_lock);
J_ASSERT(jinode->i_transaction == commit_transaction);
+ commit_transaction->t_flushed_data_blocks = 1;
jinode->i_flags &= ~JI_COMMIT_RUNNING;
wake_up_bit(&jinode->i_flags, __JI_COMMIT_RUNNING);
}
}
}
- /* Done it all: now write the commit record asynchronously. */
+ /*
+ * If the journal is not located on the file system device,
+ * then we must flush the file system device before we issue
+ * the commit record
+ */
+ if (commit_transaction->t_flushed_data_blocks &&
+ (journal->j_fs_dev != journal->j_dev) &&
+ (journal->j_flags & JBD2_BARRIER))
+ blkdev_issue_flush(journal->j_fs_dev, NULL);
+ /* Done it all: now write the commit record asynchronously. */
if (JBD2_HAS_INCOMPAT_FEATURE(journal,
JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT)) {
err = journal_submit_commit_record(journal, commit_transaction,
blkdev_issue_flush(journal->j_dev, NULL);
}
- /*
- * This is the right place to wait for data buffers both for ASYNC
- * and !ASYNC commit. If commit is ASYNC, we need to wait only after
- * the commit block went to disk (which happens above). If commit is
- * SYNC, we need to wait for data buffers before we start writing
- * commit block, which happens below in such setting.
- */
err = journal_finish_inode_data_buffers(journal, commit_transaction);
if (err) {
printk(KERN_WARNING
journal_t *journal;
int err;
- journal = kzalloc(sizeof(*journal), GFP_KERNEL|__GFP_NOFAIL);
+ journal = kzalloc(sizeof(*journal), GFP_KERNEL);
if (!journal)
goto fail;
/*
* Searching includes executable on directories, else just read.
*/
+ mask &= MAY_READ | MAY_WRITE | MAY_EXEC;
if (mask == MAY_READ || (S_ISDIR(inode->i_mode) && !(mask & MAY_WRITE)))
if (capable(CAP_DAC_READ_SEARCH))
return 0;
struct reiserfs_bitmap_info *bitmap;
unsigned int bmap_nr = reiserfs_bmap_count(sb);
+ /* Avoid lock recursion in fault case */
+ reiserfs_write_unlock(sb);
bitmap = vmalloc(sizeof(*bitmap) * bmap_nr);
+ reiserfs_write_lock(sb);
if (bitmap == NULL)
return -ENOMEM;
JOURNAL_PER_BALANCE_CNT * 2 +
2 * REISERFS_QUOTA_INIT_BLOCKS(inode->i_sb);
struct reiserfs_transaction_handle th;
+ int depth;
int err;
truncate_inode_pages(&inode->i_data, 0);
- reiserfs_write_lock(inode->i_sb);
+ depth = reiserfs_write_lock_once(inode->i_sb);
/* The = 0 happens when we abort creating a new inode for some reason like lack of space.. */
if (!(inode->i_state & I_NEW) && INODE_PKEY(inode)->k_objectid != 0) { /* also handles bad_inode case */
out:
clear_inode(inode); /* note this must go after the journal_end to prevent deadlock */
inode->i_blocks = 0;
- reiserfs_write_unlock(inode->i_sb);
+ reiserfs_write_unlock_once(inode->i_sb, depth);
}
static void _make_cpu_key(struct cpu_key *key, int version, __u32 dirid,
destroy_workqueue(commit_wq);
commit_wq = NULL;
}
- reiserfs_write_lock(sb);
free_journal_ram(sb);
+ reiserfs_write_lock(sb);
+
return 0;
}
struct reiserfs_journal *journal;
struct reiserfs_journal_list *jl;
char b[BDEVNAME_SIZE];
+ int ret;
+ /*
+ * Unlock here to avoid various RECLAIM-FS-ON <-> IN-RECLAIM-FS
+ * dependency inversion warnings.
+ */
+ reiserfs_write_unlock(sb);
journal = SB_JOURNAL(sb) = vmalloc(sizeof(struct reiserfs_journal));
if (!journal) {
reiserfs_warning(sb, "journal-1256",
"unable to get memory for journal structure");
+ reiserfs_write_lock(sb);
return 1;
}
memset(journal, 0, sizeof(struct reiserfs_journal));
INIT_LIST_HEAD(&journal->j_working_list);
INIT_LIST_HEAD(&journal->j_journal_list);
journal->j_persistent_trans = 0;
- if (reiserfs_allocate_list_bitmaps(sb,
- journal->j_list_bitmap,
- reiserfs_bmap_count(sb)))
+ ret = reiserfs_allocate_list_bitmaps(sb, journal->j_list_bitmap,
+ reiserfs_bmap_count(sb));
+ reiserfs_write_lock(sb);
+ if (ret)
goto free_and_return;
+
allocate_bitmap_nodes(sb);
/* reserved for journal area support */
reiserfs_panic(sb, "%s called without kernel lock held %d",
caller);
}
+
+#ifdef CONFIG_REISERFS_CHECK
+void reiserfs_lock_check_recursive(struct super_block *sb)
+{
+ struct reiserfs_sb_info *sb_i = REISERFS_SB(sb);
+
+ WARN_ONCE((sb_i->lock_depth > 0), "Unwanted recursive reiserfs lock!\n");
+}
+#endif
struct reiserfs_transaction_handle th;
int jbegin_count;
unsigned long savelink;
+ int depth;
inode = dentry->d_inode;
JOURNAL_PER_BALANCE_CNT * 2 + 2 +
4 * REISERFS_QUOTA_TRANS_BLOCKS(dir->i_sb);
- reiserfs_write_lock(dir->i_sb);
+ depth = reiserfs_write_lock_once(dir->i_sb);
retval = journal_begin(&th, dir->i_sb, jbegin_count);
if (retval)
goto out_unlink;
retval = journal_end(&th, dir->i_sb, jbegin_count);
reiserfs_check_path(&path);
- reiserfs_write_unlock(dir->i_sb);
+ reiserfs_write_unlock_once(dir->i_sb, depth);
return retval;
end_unlink:
if (err)
retval = err;
out_unlink:
- reiserfs_write_unlock(dir->i_sb);
+ reiserfs_write_unlock_once(dir->i_sb, depth);
return retval;
}
BUG_ON(!mutex_is_locked(&dir->i_mutex));
vfs_dq_init(dir);
- mutex_lock_nested(&dentry->d_inode->i_mutex, I_MUTEX_CHILD);
+ reiserfs_mutex_lock_nested_safe(&dentry->d_inode->i_mutex,
+ I_MUTEX_CHILD, dir->i_sb);
error = dir->i_op->unlink(dir, dentry);
mutex_unlock(&dentry->d_inode->i_mutex);
BUG_ON(!mutex_is_locked(&dir->i_mutex));
vfs_dq_init(dir);
- mutex_lock_nested(&dentry->d_inode->i_mutex, I_MUTEX_CHILD);
+ reiserfs_mutex_lock_nested_safe(&dentry->d_inode->i_mutex,
+ I_MUTEX_CHILD, dir->i_sb);
dentry_unhash(dentry);
error = dir->i_op->rmdir(dir, dentry);
if (!error)
if (IS_PRIVATE(inode) || get_inode_sd_version(inode) == STAT_DATA_V1)
return 0;
+ reiserfs_write_unlock(inode->i_sb);
dir = open_xa_dir(inode, XATTR_REPLACE);
if (IS_ERR(dir)) {
err = PTR_ERR(dir);
+ reiserfs_write_lock(inode->i_sb);
goto out;
} else if (!dir->d_inode) {
err = 0;
+ reiserfs_write_lock(inode->i_sb);
goto out_dir;
}
mutex_lock_nested(&dir->d_inode->i_mutex, I_MUTEX_XATTR);
+
+ reiserfs_write_lock(inode->i_sb);
+
buf.xadir = dir;
err = reiserfs_readdir_dentry(dir, &buf, fill_with_dentries, &pos);
while ((err == 0 || err == -ENOSPC) && buf.count) {
err = journal_begin(&th, inode->i_sb, blocks);
if (!err) {
int jerror;
- mutex_lock_nested(&dir->d_parent->d_inode->i_mutex,
- I_MUTEX_XATTR);
+ reiserfs_mutex_lock_nested_safe(
+ &dir->d_parent->d_inode->i_mutex,
+ I_MUTEX_XATTR, inode->i_sb);
err = action(dir, data);
jerror = journal_end(&th, inode->i_sb, blocks);
mutex_unlock(&dir->d_parent->d_inode->i_mutex);
if (!buffer)
return lookup_and_delete_xattr(inode, name);
+ reiserfs_write_unlock(inode->i_sb);
dentry = xattr_lookup(inode, name, flags);
- if (IS_ERR(dentry))
+ if (IS_ERR(dentry)) {
+ reiserfs_write_lock(inode->i_sb);
return PTR_ERR(dentry);
+ }
- down_write(&REISERFS_I(inode)->i_xattr_sem);
+ down_read(&REISERFS_I(inode)->i_xattr_sem);
+
+ reiserfs_write_lock(inode->i_sb);
xahash = xattr_hash(buffer, buffer_size);
while (buffer_pos < buffer_size || buffer_pos == 0) {
void __init acpi_no_s4_hw_signature(void);
void __init acpi_old_suspend_ordering(void);
void __init acpi_s4_no_nvs(void);
+void __init acpi_set_sci_en_on_resume(void);
#endif /* CONFIG_PM_SLEEP */
struct acpi_osc_context {
* blk_rq_err_bytes() : bytes left till the next error boundary
* blk_rq_sectors() : sectors left in the entire request
* blk_rq_cur_sectors() : sectors left in the current segment
- * blk_rq_err_sectors() : sectors left till the next error boundary
*/
static inline sector_t blk_rq_pos(const struct request *rq)
{
return blk_rq_cur_bytes(rq) >> 9;
}
-static inline unsigned int blk_rq_err_sectors(const struct request *rq)
-{
- return blk_rq_err_bytes(rq) >> 9;
-}
-
/*
* Request issue related functions.
*/
return q->limits.alignment_offset;
}
+static inline int queue_limit_alignment_offset(struct queue_limits *lim, sector_t offset)
+{
+ unsigned int granularity = max(lim->physical_block_size, lim->io_min);
+
+ offset &= granularity - 1;
+ return (granularity + lim->alignment_offset - offset) & (granularity - 1);
+}
+
static inline int queue_sector_alignment_offset(struct request_queue *q,
sector_t sector)
{
- return ((sector << 9) - q->limits.alignment_offset)
- & (q->limits.io_min - 1);
+ return queue_limit_alignment_offset(&q->limits, sector << 9);
}
static inline int bdev_alignment_offset(struct block_device *bdev)
* The @closure field is passed back to userspace in the response event.
* The @handle field is an out parameter, returning a handle to the allocated
* range to be used for later deallocation of the range.
+ *
+ * The address range is allocated on all local nodes. The address allocation
+ * is exclusive except for the FCP command and response registers.
*/
struct fw_cdev_allocate {
__u64 offset;
void *data, size_t length,
void *callback_data);
/*
- * Important note: The callback must guarantee that either fw_send_response()
- * or kfree() is called on the @request.
+ * Important note: Except for the FCP registers, the callback must guarantee
+ * that either fw_send_response() or kfree() is called on the @request.
*/
typedef void (*fw_address_callback_t)(struct fw_card *card,
struct fw_request *request,
#define IEEE80211_HT_CAP_DELAY_BA 0x0400
#define IEEE80211_HT_CAP_MAX_AMSDU 0x0800
#define IEEE80211_HT_CAP_DSSSCCK40 0x1000
-#define IEEE80211_HT_CAP_PSMP_SUPPORT 0x2000
+#define IEEE80211_HT_CAP_RESERVED 0x2000
#define IEEE80211_HT_CAP_40MHZ_INTOLERANT 0x4000
#define IEEE80211_HT_CAP_LSIG_TXOP_PROT 0x8000
#define IN_DEV_FORWARD(in_dev) IN_DEV_CONF_GET((in_dev), FORWARDING)
#define IN_DEV_MFORWARD(in_dev) IN_DEV_ANDCONF((in_dev), MC_FORWARDING)
#define IN_DEV_RPFILTER(in_dev) IN_DEV_MAXCONF((in_dev), RP_FILTER)
+#define IN_DEV_SRC_VMARK(in_dev) IN_DEV_ORCONF((in_dev), SRC_VMARK)
#define IN_DEV_SOURCE_ROUTE(in_dev) IN_DEV_ANDCONF((in_dev), \
ACCEPT_SOURCE_ROUTE)
#define IN_DEV_ACCEPT_LOCAL(in_dev) IN_DEV_ORCONF((in_dev), ACCEPT_LOCAL)
* waiting for it to finish.
*/
unsigned int t_synchronous_commit:1;
+ unsigned int t_flushed_data_blocks:1;
/*
* For use by the filesystem to store fs-specific data
}
/**
- * INIT_KFIFO - Initialize a kfifo declared by DECLARED_KFIFO
+ * INIT_KFIFO - Initialize a kfifo declared by DECLARE_KFIFO
* @name: name of the declared kfifo datatype
*/
#define INIT_KFIFO(name) \
resource_size_t);
void pcibios_update_irq(struct pci_dev *, int irq);
+/* Weak but can be overriden by arch */
+void pci_fixup_cardbus(struct pci_bus *);
+
/* Generic PCI functions used internally */
extern struct pci_bus *pci_find_bus(int domain, int busnr);
int reiserfs_write_lock_once(struct super_block *s);
void reiserfs_write_unlock_once(struct super_block *s, int lock_depth);
+#ifdef CONFIG_REISERFS_CHECK
+void reiserfs_lock_check_recursive(struct super_block *s);
+#else
+static inline void reiserfs_lock_check_recursive(struct super_block *s) { }
+#endif
+
/*
* Several mutexes depend on the write lock.
* However sometimes we want to relax the write lock while we hold
static inline void reiserfs_mutex_lock_safe(struct mutex *m,
struct super_block *s)
{
+ reiserfs_lock_check_recursive(s);
reiserfs_write_unlock(s);
mutex_lock(m);
reiserfs_write_lock(s);
}
+static inline void
+reiserfs_mutex_lock_nested_safe(struct mutex *m, unsigned int subclass,
+ struct super_block *s)
+{
+ reiserfs_lock_check_recursive(s);
+ reiserfs_write_unlock(s);
+ mutex_lock_nested(m, subclass);
+ reiserfs_write_lock(s);
+}
+
+static inline void
+reiserfs_down_read_safe(struct rw_semaphore *sem, struct super_block *s)
+{
+ reiserfs_lock_check_recursive(s);
+ reiserfs_write_unlock(s);
+ down_read(sem);
+ reiserfs_write_lock(s);
+}
+
/*
* When we schedule, we usually want to also release the write lock,
* according to the previous bkl based locking scheme of reiserfs.
static const struct syscall_metadata __used \
__attribute__((__aligned__(4))) \
__attribute__((section("__syscalls_metadata"))) \
- __syscall_meta_##sname = { \
+ __syscall_meta__##sname = { \
.name = "sys_"#sname, \
.nb_args = 0, \
.enter_event = &event_enter__##sname, \
NET_IPV4_CONF_ARP_ACCEPT=21,
NET_IPV4_CONF_ARP_NOTIFY=22,
NET_IPV4_CONF_ACCEPT_LOCAL=23,
+ NET_IPV4_CONF_SRC_VMARK=24,
__NET_IPV4_CONF_MAX
};
struct bdi_writeback;
int inode_wait(void *);
void writeback_inodes_sb(struct super_block *);
+int writeback_inodes_sb_if_idle(struct super_block *);
void sync_inodes_sb(struct super_block *);
void writeback_inodes_wbc(struct writeback_control *wbc);
long wb_do_writeback(struct bdi_writeback *wb, int force_wait);
* unspecified depending on the hardware capabilities flags
* @IEEE80211_HW_SIGNAL_*
* @noise: noise when receiving this frame, in dBm.
- * @qual: overall signal quality indication, in percent (0-100).
* @antenna: antenna used
* @rate_idx: index of data rate into band's supported rates or MCS index if
* HT rates are use (RX_FLAG_HT)
int freq;
int signal;
int noise;
- int __deprecated qual;
int antenna;
int rate_idx;
int flag;
local_bh_enable();
}
+/*
+ * The TX headroom reserved by mac80211 for its own tx_status functions.
+ * This is enough for the radiotap header.
+ */
+#define IEEE80211_TX_STATUS_HEADROOM 13
+
/**
* ieee80211_tx_status - transmit status callback
*
#define __LIBSRP_H__
#include <linux/list.h>
+#include <linux/kfifo.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_host.h>
#include <scsi/srp.h>
BUILD_BUG_ON(len > MAX_FILTER_STR_VAL); \
ret = trace_define_field(event_call, #type "[" #len "]", #item, \
offsetof(typeof(field), item), \
- sizeof(field.item), 0, FILTER_OTHER); \
+ sizeof(field.item), \
+ is_signed_type(type), FILTER_OTHER); \
if (ret) \
return ret;
#define __dynamic_array(type, item, len) \
ret = trace_define_field(event_call, "__data_loc " #type "[]", #item, \
offsetof(typeof(field), __data_loc_##item), \
- sizeof(field.__data_loc_##item), 0, \
- FILTER_OTHER);
+ sizeof(field.__data_loc_##item), \
+ is_signed_type(type), FILTER_OTHER);
#undef __string
#define __string(item, src) __dynamic_array(char, item, -1)
#include <linux/percpu.h>
#include <linux/sched.h>
#include <linux/init.h>
+#include <linux/cpu.h>
#include <linux/smp.h>
#include <linux/hw_breakpoint.h>
if (!cpu_events)
return ERR_PTR(-ENOMEM);
- for_each_possible_cpu(cpu) {
+ get_online_cpus();
+ for_each_online_cpu(cpu) {
pevent = per_cpu_ptr(cpu_events, cpu);
bp = perf_event_create_kernel_counter(attr, cpu, -1, triggered);
goto fail;
}
}
+ put_online_cpus();
return cpu_events;
fail:
- for_each_possible_cpu(cpu) {
+ for_each_online_cpu(cpu) {
pevent = per_cpu_ptr(cpu_events, cpu);
if (IS_ERR(*pevent))
break;
unregister_hw_breakpoint(*pevent);
}
+ put_online_cpus();
+
free_percpu(cpu_events);
- /* return the error if any */
return ERR_PTR(err);
}
EXPORT_SYMBOL_GPL(register_wide_hw_breakpoint);
/* Pre-allocate memory for max kretprobe instances */
if (rp->maxactive <= 0) {
#ifdef CONFIG_PREEMPT
- rp->maxactive = max(10, 2 * num_possible_cpus());
+ rp->maxactive = max_t(unsigned int, 10, 2*num_possible_cpus());
#else
rp->maxactive = num_possible_cpus();
#endif
GFP_KERNEL);
if (!child_ctx) {
ret = -ENOMEM;
- goto exit;
+ break;
}
__perf_event_init_context(child_ctx, child);
}
}
- if (inherited_all) {
+ if (child_ctx && inherited_all) {
/*
* Mark the child context as a clone of the parent
* context, or of whatever the parent is a clone of.
get_ctx(child_ctx->parent_ctx);
}
-exit:
mutex_unlock(&parent_ctx->mutex);
perf_unpin_context(parent_ctx);
config HAVE_FTRACE_NMI_ENTER
bool
help
- See Documentation/trace/ftrace-implementation.txt
+ See Documentation/trace/ftrace-design.txt
config HAVE_FUNCTION_TRACER
bool
help
- See Documentation/trace/ftrace-implementation.txt
+ See Documentation/trace/ftrace-design.txt
config HAVE_FUNCTION_GRAPH_TRACER
bool
help
- See Documentation/trace/ftrace-implementation.txt
+ See Documentation/trace/ftrace-design.txt
config HAVE_FUNCTION_GRAPH_FP_TEST
bool
config HAVE_FUNCTION_TRACE_MCOUNT_TEST
bool
help
- See Documentation/trace/ftrace-implementation.txt
+ See Documentation/trace/ftrace-design.txt
config HAVE_DYNAMIC_FTRACE
bool
help
- See Documentation/trace/ftrace-implementation.txt
+ See Documentation/trace/ftrace-design.txt
config HAVE_FTRACE_MCOUNT_RECORD
bool
help
- See Documentation/trace/ftrace-implementation.txt
+ See Documentation/trace/ftrace-design.txt
config HAVE_HW_BRANCH_TRACER
bool
config HAVE_SYSCALL_TRACEPOINTS
bool
help
- See Documentation/trace/ftrace-implementation.txt
+ See Documentation/trace/ftrace-design.txt
config TRACER_MAX_TRACE
bool
# This allows those options to appear when no other tracer is selected. But the
# options do not appear when something else selects it. We need the two options
# GENERIC_TRACER and TRACING to avoid circular dependencies to accomplish the
-# hidding of the automatic options.
+# hiding of the automatic options.
config TRACING
bool
bool "Tracers"
default y if DEBUG_KERNEL
help
- Enable the kernel tracing infrastructure.
+ Enable the kernel tracing infrastructure.
if FTRACE
help
Enable the kernel to trace every kernel function. This is done
by using a compiler feature to insert a small, 5-byte No-Operation
- instruction to the beginning of every kernel function, which NOP
+ instruction at the beginning of every kernel function, which NOP
sequence is then dynamically patched into a tracer call when
tracing is enabled by the administrator. If it's runtime disabled
(the bootup default), then the overhead of the instructions is very
and its entry.
Its first purpose is to trace the duration of functions and
draw a call graph for each thread with some information like
- the return value. This is done by setting the current return
+ the return value. This is done by setting the current return
address on the current task structure into a stack of calls.
echo 0 > /sys/kernel/debug/tracing/tracing_max_latency
- (Note that kernel size and overhead increases with this option
+ (Note that kernel size and overhead increase with this option
enabled. This option and the preempt-off timing option can be
used together or separately.)
select TRACER_MAX_TRACE
select RING_BUFFER_ALLOW_SWAP
help
- This option measures the time spent in preemption off critical
+ This option measures the time spent in preemption-off critical
sections, with microsecond accuracy.
The default measurement method is a maximum search, which is
echo 0 > /sys/kernel/debug/tracing/tracing_max_latency
- (Note that kernel size and overhead increases with this option
+ (Note that kernel size and overhead increase with this option
enabled. This option and the irqs-off timing option can be
used together or separately.)
depends on !GENERIC_TRACER
select TRACING
help
- This tracer hooks to various trace points in the kernel
+ This tracer hooks to various trace points in the kernel,
allowing the user to pick and choose which trace point they
want to trace. It also includes the sched_switch tracer plugin.
The likely/unlikely profiler only looks at the conditions that
are annotated with a likely or unlikely macro.
- The "all branch" profiler will profile every if statement in the
+ The "all branch" profiler will profile every if-statement in the
kernel. This profiler will also enable the likely/unlikely
- profiler as well.
+ profiler.
- Either of the above profilers add a bit of overhead to the system.
- If unsure choose "No branch profiling".
+ Either of the above profilers adds a bit of overhead to the system.
+ If unsure, choose "No branch profiling".
config BRANCH_PROFILE_NONE
bool "No branch profiling"
help
- No branch profiling. Branch profiling adds a bit of overhead.
- Only enable it if you want to analyse the branching behavior.
- Otherwise keep it disabled.
+ No branch profiling. Branch profiling adds a bit of overhead.
+ Only enable it if you want to analyse the branching behavior.
+ Otherwise keep it disabled.
config PROFILE_ANNOTATED_BRANCHES
bool "Trace likely/unlikely profiler"
/sys/kernel/debug/tracing/profile_annotated_branch
- Note: this will add a significant overhead, only turn this
+ Note: this will add a significant overhead; only turn this
on if you need to profile the system's use of these macros.
config PROFILE_ALL_BRANCHES
This configuration, when enabled, will impose a great overhead
on the system. This should only be enabled when the system
- is to be analyzed
+ is to be analyzed in much detail.
endchoice
config TRACING_BRANCHES
depends on X86
select GENERIC_TRACER
help
- This tracer helps developers to analyze and optimize the kernels
+ This tracer helps developers to analyze and optimize the kernel's
power management decisions, specifically the C-state and P-state
behavior.
select GENERIC_TRACER
help
This tracer records all branches on the system in a circular
- buffer giving access to the last N branches for each cpu.
+ buffer, giving access to the last N branches for each cpu.
config KMEMTRACE
bool "Trace SLAB allocations"
select GENERIC_TRACER
help
kmemtrace provides tracing for slab allocator functions, such as
- kmalloc, kfree, kmem_cache_alloc, kmem_cache_free etc.. Collected
+ kmalloc, kfree, kmem_cache_alloc, kmem_cache_free, etc. Collected
data is then fed to the userspace application in order to analyse
allocation hotspots, internal fragmentation and so on, making it
possible to see how well an allocator performs, as well as debug
bool "Trace workqueues"
select GENERIC_TRACER
help
- The workqueue tracer provides some statistical informations
+ The workqueue tracer provides some statistical information
about each cpu workqueue thread such as the number of the
works inserted and executed since their creation. It can help
- to evaluate the amount of work each of them have to perform.
+ to evaluate the amount of work each of them has to perform.
For example it can help a developer to decide whether he should
- choose a per cpu workqueue instead of a singlethreaded one.
+ choose a per-cpu workqueue instead of a singlethreaded one.
config BLK_DEV_IO_TRACE
- bool "Support for tracing block io actions"
+ bool "Support for tracing block IO actions"
depends on SYSFS
depends on BLOCK
select RELAY
select TRACING
default y
help
- This allows the user to add tracing events (similar to tracepoints) on the fly
- via the ftrace interface. See Documentation/trace/kprobetrace.txt
- for more details.
+ This allows the user to add tracing events (similar to tracepoints)
+ on the fly via the ftrace interface. See
+ Documentation/trace/kprobetrace.txt for more details.
Those events can be inserted wherever kprobes can probe, and record
various register and memory values.
- This option is also required by perf-probe subcommand of perf tools. If
- you want to use perf tools, this option is strongly recommended.
+ This option is also required by perf-probe subcommand of perf tools.
+ If you want to use perf tools, this option is strongly recommended.
config DYNAMIC_FTRACE
bool "enable/disable ftrace tracepoints dynamically"
depends on HAVE_DYNAMIC_FTRACE
default y
help
- This option will modify all the calls to ftrace dynamically
- (will patch them out of the binary image and replaces them
- with a No-Op instruction) as they are called. A table is
- created to dynamically enable them again.
+ This option will modify all the calls to ftrace dynamically
+ (will patch them out of the binary image and replace them
+ with a No-Op instruction) as they are called. A table is
+ created to dynamically enable them again.
- This way a CONFIG_FUNCTION_TRACER kernel is slightly larger, but otherwise
- has native performance as long as no tracing is active.
+ This way a CONFIG_FUNCTION_TRACER kernel is slightly larger, but
+ otherwise has native performance as long as no tracing is active.
- The changes to the code are done by a kernel thread that
- wakes up once a second and checks to see if any ftrace calls
- were made. If so, it runs stop_machine (stops all CPUS)
- and modifies the code to jump over the call to ftrace.
+ The changes to the code are done by a kernel thread that
+ wakes up once a second and checks to see if any ftrace calls
+ were made. If so, it runs stop_machine (stops all CPUS)
+ and modifies the code to jump over the call to ftrace.
config FUNCTION_PROFILER
bool "Kernel function profiler"
depends on FUNCTION_TRACER
default n
help
- This option enables the kernel function profiler. A file is created
- in debugfs called function_profile_enabled which defaults to zero.
- When a 1 is echoed into this file profiling begins, and when a
- zero is entered, profiling stops. A file in the trace_stats
- directory called functions, that show the list of functions that
- have been hit and their counters.
+ This option enables the kernel function profiler. A file is created
+ in debugfs called function_profile_enabled which defaults to zero.
+ When a 1 is echoed into this file profiling begins, and when a
+ zero is entered, profiling stops. A "functions" file is created in
+ the trace_stats directory; this file shows the list of functions that
+ have been hit and their counters.
- If in doubt, say N
+ If in doubt, say N.
config FTRACE_MCOUNT_RECORD
def_bool y
tristate "Ring buffer benchmark stress tester"
depends on RING_BUFFER
help
- This option creates a test to stress the ring buffer and bench mark it.
- It creates its own ring buffer such that it will not interfer with
+ This option creates a test to stress the ring buffer and benchmark it.
+ It creates its own ring buffer such that it will not interfere with
any other users of the ring buffer (such as ftrace). It then creates
a producer and consumer that will run for 10 seconds and sleep for
10 seconds. Each interval it will print out the number of events
It does not disable interrupts or raise its priority, so it may be
affected by processes that are running.
- If unsure, say N
+ If unsure, say N.
endif # FTRACE
if (!!(topt->flags->val & topt->opt->bit) != val) {
mutex_lock(&trace_types_lock);
ret = __set_tracer_option(current_trace, topt->flags,
- topt->opt, val);
+ topt->opt, !val);
mutex_unlock(&trace_types_lock);
if (ret)
return ret;
BUILD_BUG_ON(len > MAX_FILTER_STR_VAL); \
ret = trace_define_field(event_call, #type "[" #len "]", #item, \
offsetof(typeof(field), item), \
- sizeof(field.item), 0, FILTER_OTHER); \
+ sizeof(field.item), \
+ is_signed_type(type), FILTER_OTHER); \
if (ret) \
return ret;
ret = trace_define_field(event_call, #type "[" #len "]", #item, \
offsetof(typeof(field), \
container.item), \
- sizeof(field.container.item), 0, \
- FILTER_OTHER); \
+ sizeof(field.container.item), \
+ is_signed_type(type), FILTER_OTHER); \
if (ret) \
return ret;
#undef SHOW_FIELD
#define SHOW_FIELD(type, item, name) \
do { \
- ret = trace_seq_printf(s, "\tfield: " #type " %s;\t" \
- "offset:%u;\tsize:%u;\n", name, \
+ ret = trace_seq_printf(s, "\tfield:" #type " %s;\t" \
+ "offset:%u;\tsize:%u;\tsigned:%d;\n", name,\
(unsigned int)offsetof(typeof(field), item),\
- (unsigned int)sizeof(type)); \
+ (unsigned int)sizeof(type), \
+ is_signed_type(type)); \
if (!ret) \
return 0; \
} while (0)
#include <linux/fs.h>
#include "trace_output.h"
-#include "trace_stat.h"
#include "trace.h"
#include <linux/hw_breakpoint.h>
#include <asm/hw_breakpoint.h>
+#include <asm/atomic.h>
+
/*
* For now, let us restrict the no. of symbols traced simultaneously to number
* of available hardware breakpoint registers.
struct perf_event **ksym_hbp;
struct perf_event_attr attr;
#ifdef CONFIG_PROFILE_KSYM_TRACER
- unsigned long counter;
+ atomic64_t counter;
#endif
struct hlist_node ksym_hlist;
};
rcu_read_lock();
hlist_for_each_entry_rcu(entry, node, &ksym_filter_head, ksym_hlist) {
- if ((entry->attr.bp_addr == hbp_hit_addr) &&
- (entry->counter <= MAX_UL_INT)) {
- entry->counter++;
+ if (entry->attr.bp_addr == hbp_hit_addr) {
+ atomic64_inc(&entry->counter);
break;
}
}
entry->attr.bp_addr = addr;
entry->attr.bp_len = HW_BREAKPOINT_LEN_4;
- ret = -EAGAIN;
entry->ksym_hbp = register_wide_hw_breakpoint(&entry->attr,
ksym_hbp_handler);
* 2: echo 0 > ksym_trace_filter
* 3: echo "*:---" > ksym_trace_filter
*/
- if (!buf[0] || !strcmp(buf, "0") ||
- !strcmp(buf, "*:---")) {
+ if (!input_string[0] || !strcmp(input_string, "0") ||
+ !strcmp(input_string, "*:---")) {
__ksym_trace_reset();
ret = 0;
goto out;
.print_line = ksym_trace_output
};
-__init static int init_ksym_trace(void)
-{
- struct dentry *d_tracer;
- struct dentry *entry;
-
- d_tracer = tracing_init_dentry();
- ksym_filter_entry_count = 0;
-
- entry = debugfs_create_file("ksym_trace_filter", 0644, d_tracer,
- NULL, &ksym_tracing_fops);
- if (!entry)
- pr_warning("Could not create debugfs "
- "'ksym_trace_filter' file\n");
-
- return register_tracer(&ksym_tracer);
-}
-device_initcall(init_ksym_trace);
-
-
#ifdef CONFIG_PROFILE_KSYM_TRACER
-static int ksym_tracer_stat_headers(struct seq_file *m)
+static int ksym_profile_show(struct seq_file *m, void *v)
{
+ struct hlist_node *node;
+ struct trace_ksym *entry;
+ int access_type = 0;
+ char fn_name[KSYM_NAME_LEN];
+
seq_puts(m, " Access Type ");
seq_puts(m, " Symbol Counter\n");
seq_puts(m, " ----------- ");
seq_puts(m, " ------ -------\n");
- return 0;
-}
-static int ksym_tracer_stat_show(struct seq_file *m, void *v)
-{
- struct hlist_node *stat = v;
- struct trace_ksym *entry;
- int access_type = 0;
- char fn_name[KSYM_NAME_LEN];
+ rcu_read_lock();
+ hlist_for_each_entry_rcu(entry, node, &ksym_filter_head, ksym_hlist) {
- entry = hlist_entry(stat, struct trace_ksym, ksym_hlist);
+ access_type = entry->attr.bp_type;
- access_type = entry->attr.bp_type;
+ switch (access_type) {
+ case HW_BREAKPOINT_R:
+ seq_puts(m, " R ");
+ break;
+ case HW_BREAKPOINT_W:
+ seq_puts(m, " W ");
+ break;
+ case HW_BREAKPOINT_R | HW_BREAKPOINT_W:
+ seq_puts(m, " RW ");
+ break;
+ default:
+ seq_puts(m, " NA ");
+ }
- switch (access_type) {
- case HW_BREAKPOINT_R:
- seq_puts(m, " R ");
- break;
- case HW_BREAKPOINT_W:
- seq_puts(m, " W ");
- break;
- case HW_BREAKPOINT_R | HW_BREAKPOINT_W:
- seq_puts(m, " RW ");
- break;
- default:
- seq_puts(m, " NA ");
+ if (lookup_symbol_name(entry->attr.bp_addr, fn_name) >= 0)
+ seq_printf(m, " %-36s", fn_name);
+ else
+ seq_printf(m, " %-36s", "<NA>");
+ seq_printf(m, " %15llu\n",
+ (unsigned long long)atomic64_read(&entry->counter));
}
-
- if (lookup_symbol_name(entry->attr.bp_addr, fn_name) >= 0)
- seq_printf(m, " %-36s", fn_name);
- else
- seq_printf(m, " %-36s", "<NA>");
- seq_printf(m, " %15lu\n", entry->counter);
+ rcu_read_unlock();
return 0;
}
-static void *ksym_tracer_stat_start(struct tracer_stat *trace)
+static int ksym_profile_open(struct inode *node, struct file *file)
{
- return ksym_filter_head.first;
-}
-
-static void *
-ksym_tracer_stat_next(void *v, int idx)
-{
- struct hlist_node *stat = v;
-
- return stat->next;
+ return single_open(file, ksym_profile_show, NULL);
}
-static struct tracer_stat ksym_tracer_stats = {
- .name = "ksym_tracer",
- .stat_start = ksym_tracer_stat_start,
- .stat_next = ksym_tracer_stat_next,
- .stat_headers = ksym_tracer_stat_headers,
- .stat_show = ksym_tracer_stat_show
+static const struct file_operations ksym_profile_fops = {
+ .open = ksym_profile_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
};
+#endif /* CONFIG_PROFILE_KSYM_TRACER */
-__init static int ksym_tracer_stat_init(void)
+__init static int init_ksym_trace(void)
{
- int ret;
+ struct dentry *d_tracer;
- ret = register_stat_tracer(&ksym_tracer_stats);
- if (ret) {
- printk(KERN_WARNING "Warning: could not register "
- "ksym tracer stats\n");
- return 1;
- }
+ d_tracer = tracing_init_dentry();
- return 0;
+ trace_create_file("ksym_trace_filter", 0644, d_tracer,
+ NULL, &ksym_tracing_fops);
+
+#ifdef CONFIG_PROFILE_KSYM_TRACER
+ trace_create_file("ksym_profile", 0444, d_tracer,
+ NULL, &ksym_profile_fops);
+#endif
+
+ return register_tracer(&ksym_tracer);
}
-fs_initcall(ksym_tracer_stat_init);
-#endif /* CONFIG_PROFILE_KSYM_TRACER */
+device_initcall(init_ksym_trace);
return count;
}
-static int dma_debug_device_change(struct notifier_block *nb,
- unsigned long action, void *data)
+static int dma_debug_device_change(struct notifier_block *nb, unsigned long action, void *data)
{
struct device *dev = data;
int count;
+ if (global_disable)
+ return 0;
switch (action) {
case BUS_NOTIFY_UNBOUND_DRIVER:
{
struct notifier_block *nb;
+ if (global_disable)
+ return;
+
nb = kzalloc(sizeof(struct notifier_block), GFP_KERNEL);
if (nb == NULL) {
pr_err("dma_debug_add_bus: out of memory\n");
}
EXPORT_SYMBOL(do_mmap_pgoff);
+SYSCALL_DEFINE6(mmap_pgoff, unsigned long, addr, unsigned long, len,
+ unsigned long, prot, unsigned long, flags,
+ unsigned long, fd, unsigned long, pgoff)
+{
+ struct file *file = NULL;
+ unsigned long retval = -EBADF;
+
+ if (!(flags & MAP_ANONYMOUS)) {
+ if (unlikely(flags & MAP_HUGETLB))
+ return -EINVAL;
+ file = fget(fd);
+ if (!file)
+ goto out;
+ } else if (flags & MAP_HUGETLB) {
+ struct user_struct *user = NULL;
+ /*
+ * VM_NORESERVE is used because the reservations will be
+ * taken when vm_ops->mmap() is called
+ * A dummy user value is used because we are not locking
+ * memory so no accounting is necessary
+ */
+ len = ALIGN(len, huge_page_size(&default_hstate));
+ file = hugetlb_file_setup(HUGETLB_ANON_FILE, len, VM_NORESERVE,
+ &user, HUGETLB_ANONHUGE_INODE);
+ if (IS_ERR(file))
+ return PTR_ERR(file);
+ }
+
+ flags &= ~(MAP_EXECUTABLE | MAP_DENYWRITE);
+
+ down_write(¤t->mm->mmap_sem);
+ retval = do_mmap_pgoff(file, addr, len, prot, flags, pgoff);
+ up_write(¤t->mm->mmap_sem);
+
+ if (file)
+ fput(file);
+out:
+ return retval;
+}
+
/*
* Some shared mappigns will want the pages marked read-only
* to track write events. If so, we'll downgrade vm_page_prot
}
EXPORT_SYMBOL(do_mmap_pgoff);
+SYSCALL_DEFINE6(mmap_pgoff, unsigned long, addr, unsigned long, len,
+ unsigned long, prot, unsigned long, flags,
+ unsigned long, fd, unsigned long, pgoff)
+{
+ struct file *file = NULL;
+ unsigned long retval = -EBADF;
+
+ if (!(flags & MAP_ANONYMOUS)) {
+ file = fget(fd);
+ if (!file)
+ goto out;
+ }
+
+ flags &= ~(MAP_EXECUTABLE | MAP_DENYWRITE);
+
+ down_write(¤t->mm->mmap_sem);
+ retval = do_mmap_pgoff(file, addr, len, prot, flags, pgoff);
+ up_write(¤t->mm->mmap_sem);
+
+ if (file)
+ fput(file);
+out:
+ return retval;
+}
+
/*
* split a vma into two pieces at address 'addr', a new vma is allocated either
* for the first part or the tail.
l3 = s->cs_cachep->nodelists[q];
if (!l3 || OFF_SLAB(s->cs_cachep))
- return;
+ continue;
lockdep_set_class(&l3->list_lock, &on_slab_l3_key);
alc = l3->alien;
/*
* for alloc_alien_cache,
*/
if (!alc || (unsigned long)alc == BAD_ALIEN_MAGIC)
- return;
+ continue;
for_each_node(r) {
if (alc[r])
lockdep_set_class(&alc[r]->lock,
#include <linux/module.h>
#include <linux/err.h>
#include <linux/sched.h>
-#include <linux/hugetlb.h>
-#include <linux/syscalls.h>
-#include <linux/mman.h>
-#include <linux/file.h>
#include <asm/uaccess.h>
#define CREATE_TRACE_POINTS
}
EXPORT_SYMBOL_GPL(get_user_pages_fast);
-SYSCALL_DEFINE6(mmap_pgoff, unsigned long, addr, unsigned long, len,
- unsigned long, prot, unsigned long, flags,
- unsigned long, fd, unsigned long, pgoff)
-{
- struct file * file = NULL;
- unsigned long retval = -EBADF;
-
- if (!(flags & MAP_ANONYMOUS)) {
- if (unlikely(flags & MAP_HUGETLB))
- return -EINVAL;
- file = fget(fd);
- if (!file)
- goto out;
- } else if (flags & MAP_HUGETLB) {
- struct user_struct *user = NULL;
- /*
- * VM_NORESERVE is used because the reservations will be
- * taken when vm_ops->mmap() is called
- * A dummy user value is used because we are not locking
- * memory so no accounting is necessary
- */
- len = ALIGN(len, huge_page_size(&default_hstate));
- file = hugetlb_file_setup(HUGETLB_ANON_FILE, len, VM_NORESERVE,
- &user, HUGETLB_ANONHUGE_INODE);
- if (IS_ERR(file))
- return PTR_ERR(file);
- }
-
- flags &= ~(MAP_EXECUTABLE | MAP_DENYWRITE);
-
- down_write(¤t->mm->mmap_sem);
- retval = do_mmap_pgoff(file, addr, len, prot, flags, pgoff);
- up_write(¤t->mm->mmap_sem);
-
- if (file)
- fput(file);
-out:
- return retval;
-}
-
/* Tracepoints definitions. */
EXPORT_TRACEPOINT_SYMBOL(kmalloc);
EXPORT_TRACEPOINT_SYMBOL(kmem_cache_alloc);
__u64 count; /* Default No packets to send */
__u64 sofar; /* How many pkts we've sent so far */
__u64 tx_bytes; /* How many bytes we've transmitted */
- __u64 errors; /* Errors when trying to transmit,
- pkts will be re-sent */
+ __u64 errors; /* Errors when trying to transmit, */
/* runtime counters relating to clone_skb */
pkt_dev->seq_num++;
pkt_dev->tx_bytes += pkt_dev->last_pkt_size;
break;
+ case NET_XMIT_DROP:
+ case NET_XMIT_CN:
+ case NET_XMIT_POLICED:
+ /* skb has been consumed */
+ pkt_dev->errors++;
+ break;
default: /* Drivers are not supposed to return other values! */
if (net_ratelimit())
pr_info("pktgen: %s xmit error: %d\n",
DEVINET_SYSCTL_RW_ENTRY(ACCEPT_SOURCE_ROUTE,
"accept_source_route"),
DEVINET_SYSCTL_RW_ENTRY(ACCEPT_LOCAL, "accept_local"),
+ DEVINET_SYSCTL_RW_ENTRY(SRC_VMARK, "src_valid_mark"),
DEVINET_SYSCTL_RW_ENTRY(PROXY_ARP, "proxy_arp"),
DEVINET_SYSCTL_RW_ENTRY(MEDIUM_ID, "medium_id"),
DEVINET_SYSCTL_RW_ENTRY(BOOTP_RELAY, "bootp_relay"),
no_addr = in_dev->ifa_list == NULL;
rpf = IN_DEV_RPFILTER(in_dev);
accept_local = IN_DEV_ACCEPT_LOCAL(in_dev);
+ if (mark && !IN_DEV_SRC_VMARK(in_dev))
+ fl.mark = 0;
}
rcu_read_unlock();
ht_cap->ht_supported = true;
- ht_cap->cap = le16_to_cpu(ht_cap_ie->cap_info) & sband->ht_cap.cap;
- ht_cap->cap &= ~IEEE80211_HT_CAP_SM_PS;
- ht_cap->cap |= sband->ht_cap.cap & IEEE80211_HT_CAP_SM_PS;
+ /*
+ * The bits listed in this expression should be
+ * the same for the peer and us, if the station
+ * advertises more then we can't use those thus
+ * we mask them out.
+ */
+ ht_cap->cap = le16_to_cpu(ht_cap_ie->cap_info) &
+ (sband->ht_cap.cap |
+ ~(IEEE80211_HT_CAP_LDPC_CODING |
+ IEEE80211_HT_CAP_SUP_WIDTH_20_40 |
+ IEEE80211_HT_CAP_GRN_FLD |
+ IEEE80211_HT_CAP_SGI_20 |
+ IEEE80211_HT_CAP_SGI_40 |
+ IEEE80211_HT_CAP_DSSSCCK40));
+ /*
+ * The STBC bits are asymmetric -- if we don't have
+ * TX then mask out the peer's RX and vice versa.
+ */
+ if (!(sband->ht_cap.cap & IEEE80211_HT_CAP_TX_STBC))
+ ht_cap->cap &= ~IEEE80211_HT_CAP_RX_STBC;
+ if (!(sband->ht_cap.cap & IEEE80211_HT_CAP_RX_STBC))
+ ht_cap->cap &= ~IEEE80211_HT_CAP_TX_STBC;
ampdu_info = ht_cap_ie->ampdu_params_info;
ht_cap->ampdu_factor =
struct sta_info *ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
u8 *bssid,u8 *addr, u32 supp_rates)
{
+ struct ieee80211_if_ibss *ifibss = &sdata->u.ibss;
struct ieee80211_local *local = sdata->local;
struct sta_info *sta;
int band = local->hw.conf.channel->band;
return NULL;
}
+ if (ifibss->state == IEEE80211_IBSS_MLME_SEARCH)
+ return NULL;
+
if (compare_ether_addr(bssid, sdata->u.ibss.bssid))
return NULL;
* and we need some headroom for passing the frame to monitor
* interfaces, but never both at the same time.
*/
+ BUILD_BUG_ON(IEEE80211_TX_STATUS_HEADROOM !=
+ sizeof(struct ieee80211_tx_status_rtap_hdr));
local->tx_headroom = max_t(unsigned int , local->hw.extra_tx_headroom,
sizeof(struct ieee80211_tx_status_rtap_hdr));
sdata->u.mgd.flags &= ~(IEEE80211_STA_CONNECTION_POLL |
IEEE80211_STA_BEACON_POLL);
+ /*
+ * Always handle WMM once after association regardless
+ * of the first value the AP uses. Setting -1 here has
+ * that effect because the AP values is an unsigned
+ * 4-bit value.
+ */
+ sdata->u.mgd.wmm_last_param_set = -1;
+
ieee80211_led_assoc(local, 1);
sdata->vif.bss_conf.assoc = 1;
if (!local->ps_sdata)
return false;
+ /* No point if we're going to suspend */
+ if (local->quiescing)
+ return false;
+
return true;
}
/* restart hardware */
if (local->open_count) {
+ /*
+ * Upon resume hardware can sometimes be goofy due to
+ * various platform / driver / bus issues, so restarting
+ * the device may at times not work immediately. Propagate
+ * the error.
+ */
res = drv_start(local);
+ if (res) {
+ WARN(local->suspended, "Harware became unavailable "
+ "upon resume. This is could be a software issue"
+ "prior to suspend or a harware issue\n");
+ return res;
+ }
ieee80211_led_radio(local, true);
}
}
}
- WARN_ON(!bss);
+ /*
+ * We might be coming here because the driver reported
+ * a successful association at the same time as the
+ * user requested a deauth. In that case, we will have
+ * removed the BSS from the auth_bsses list due to the
+ * deauth request when the assoc response makes it. If
+ * the two code paths acquire the lock the other way
+ * around, that's just the standard situation of a
+ * deauth being requested while connected.
+ */
+ if (!bss)
+ goto out;
} else if (wdev->conn) {
cfg80211_sme_failed_assoc(wdev);
/*
struct cfg80211_registered_device *rdev;
struct wiphy *wiphy;
struct iw_scan_req *wreq = NULL;
- struct cfg80211_scan_request *creq;
+ struct cfg80211_scan_request *creq = NULL;
int i, err, n_channels = 0;
enum ieee80211_band band;
/* translate "Scan for SSID" request */
if (wreq) {
if (wrqu->data.flags & IW_SCAN_THIS_ESSID) {
- if (wreq->essid_len > IEEE80211_MAX_SSID_LEN)
- return -EINVAL;
+ if (wreq->essid_len > IEEE80211_MAX_SSID_LEN) {
+ err = -EINVAL;
+ goto out;
+ }
memcpy(creq->ssids[0].ssid, wreq->essid, wreq->essid_len);
creq->ssids[0].ssid_len = wreq->essid_len;
}
err = rdev->ops->scan(wiphy, dev, creq);
if (err) {
rdev->scan_req = NULL;
- kfree(creq);
+ /* creq will be freed below */
} else {
nl80211_send_scan_start(rdev, dev);
+ /* creq now owned by driver */
+ creq = NULL;
dev_hold(dev);
}
out:
+ kfree(creq);
cfg80211_unlock_rdev(rdev);
return err;
}
if (!dev)
goto free_dst;
- /* Copy neighbout for reachability confirmation */
+ /* Copy neighbour for reachability confirmation */
dst0->neighbour = neigh_clone(dst->neighbour);
xfrm_init_path((struct xfrm_dst *)dst0, dst, nfheader_len);
struct snd_pcm_hw_params *params)
{
int err;
+ struct aaci *aaci = substream->private_data;
aaci_pcm_hw_free(substream);
if (aacirun->pcm_open) {
static int aaci_pcm_playback_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params)
{
- struct aaci *aaci = substream->private_data;
struct aaci_runtime *aacirun = substream->runtime->private_data;
unsigned int channels = params_channels(params);
int ret;
static int aaci_pcm_capture_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params)
{
- struct aaci *aaci = substream->private_data;
struct aaci_runtime *aacirun = substream->runtime->private_data;
int ret;
err = snd_pcm_hw_constraint_minmax(runtime, SNDRV_PCM_HW_PARAM_RATE,
hw->rate_min, hw->rate_max);
- if (err < 0)
- return err;
+ if (err < 0)
+ return err;
err = snd_pcm_hw_constraint_minmax(runtime, SNDRV_PCM_HW_PARAM_PERIOD_BYTES,
hw->period_bytes_min, hw->period_bytes_max);
- if (err < 0)
- return err;
+ if (err < 0)
+ return err;
err = snd_pcm_hw_constraint_minmax(runtime, SNDRV_PCM_HW_PARAM_PERIODS,
hw->periods_min, hw->periods_max);
return;
/* generate tone */
- snd_hda_codec_write_cache(codec, beep->nid, 0,
+ snd_hda_codec_write(codec, beep->nid, 0,
AC_VERB_SET_BEEP_CONTROL, beep->tone);
}
beep->dev = NULL;
cancel_work_sync(&beep->beep_work);
/* turn off beep for sure */
- snd_hda_codec_write_cache(beep->codec, beep->nid, 0,
+ snd_hda_codec_write(beep->codec, beep->nid, 0,
AC_VERB_SET_BEEP_CONTROL, 0);
}
beep->enabled = enable;
if (!enable) {
/* turn off beep */
- snd_hda_codec_write_cache(beep->codec, beep->nid, 0,
+ snd_hda_codec_write(beep->codec, beep->nid, 0,
AC_VERB_SET_BEEP_CONTROL, 0);
}
if (beep->mode == HDA_BEEP_MODE_SWREG) {
mutex_init(&beep->mutex);
if (beep->mode == HDA_BEEP_MODE_ON) {
- beep->enabled = 1;
- snd_hda_do_register(&beep->register_work);
+ int err = snd_hda_do_attach(beep);
+ if (err < 0) {
+ kfree(beep);
+ codec->beep = NULL;
+ return err;
+ }
}
return 0;
if (beep) {
cancel_work_sync(&beep->register_work);
cancel_delayed_work(&beep->unregister_work);
- if (beep->enabled)
+ if (beep->dev)
snd_hda_do_detach(beep);
codec->beep = NULL;
kfree(beep);
*/
u32 snd_hda_pin_sense(struct hda_codec *codec, hda_nid_t nid)
{
- u32 pincap = snd_hda_query_pin_caps(codec, nid);
-
- if (pincap & AC_PINCAP_TRIG_REQ) /* need trigger? */
- snd_hda_codec_read(codec, nid, 0, AC_VERB_SET_PIN_SENSE, 0);
+ u32 pincap;
+ if (!codec->no_trigger_sense) {
+ pincap = snd_hda_query_pin_caps(codec, nid);
+ if (pincap & AC_PINCAP_TRIG_REQ) /* need trigger? */
+ snd_hda_codec_read(codec, nid, 0, AC_VERB_SET_PIN_SENSE, 0);
+ }
return snd_hda_codec_read(codec, nid, 0,
AC_VERB_GET_PIN_SENSE, 0);
}
unsigned int pin_amp_workaround:1; /* pin out-amp takes index
* (e.g. Conexant codecs)
*/
+ unsigned int no_trigger_sense:1; /* don't trigger at pin-sensing */
#ifdef CONFIG_SND_HDA_POWER_SAVE
unsigned int power_on :1; /* current (global) power-state */
unsigned int power_transition :1; /* power-state in transition */
*/
unsigned char stream_tag; /* assigned stream */
unsigned char index; /* stream index */
+ int device; /* last device number assigned to */
unsigned int opened :1;
unsigned int running :1;
*/
/* assign a stream for the PCM */
-static inline struct azx_dev *azx_assign_device(struct azx *chip, int stream)
+static inline struct azx_dev *
+azx_assign_device(struct azx *chip, struct snd_pcm_substream *substream)
{
int dev, i, nums;
- if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
+ struct azx_dev *res = NULL;
+
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
dev = chip->playback_index_offset;
nums = chip->playback_streams;
} else {
}
for (i = 0; i < nums; i++, dev++)
if (!chip->azx_dev[dev].opened) {
- chip->azx_dev[dev].opened = 1;
- return &chip->azx_dev[dev];
+ res = &chip->azx_dev[dev];
+ if (res->device == substream->pcm->device)
+ break;
}
- return NULL;
+ if (res) {
+ res->opened = 1;
+ res->device = substream->pcm->device;
+ }
+ return res;
}
/* release the assigned stream */
int err;
mutex_lock(&chip->open_mutex);
- azx_dev = azx_assign_device(chip, substream->stream);
+ azx_dev = azx_assign_device(chip, substream);
if (azx_dev == NULL) {
mutex_unlock(&chip->open_mutex);
return -EBUSY;
*/
spec->multiout.no_share_stream = 1;
+ codec->no_trigger_sense = 1;
+
return 0;
}
codec->patch_ops = ad198x_patch_ops;
+ codec->no_trigger_sense = 1;
+
return 0;
}
codec->patch_ops.unsol_event = ad1981_hp_unsol_event;
break;
}
+
+ codec->no_trigger_sense = 1;
+
return 0;
}
#endif
spec->vmaster_nid = 0x04;
+ codec->no_trigger_sense = 1;
+
return 0;
}
codec->patch_ops = ad198x_patch_ops;
+ codec->no_trigger_sense = 1;
+
return 0;
}
break;
}
+ codec->no_trigger_sense = 1;
+
return 0;
}
spec->mixers[2] = ad1882_6stack_mixers;
break;
}
+
+ codec->no_trigger_sense = 1;
+
return 0;
}
{
if (!nid)
return 0;
- /* NOTE: we can't use snd_hda_jack_detect() here because STAC/IDT
- * codecs behave wrongly when SET_PIN_SENSE is triggered, although
- * the pincap gives TRIG_REQ bit.
- */
- if (snd_hda_codec_read(codec, nid, 0, AC_VERB_GET_PIN_SENSE, 0) &
- AC_PINSENSE_PRESENCE)
- return 1;
- return 0;
+ return snd_hda_jack_detect(codec, nid);
}
static void stac92xx_line_out_detect(struct hda_codec *codec,
if (spec == NULL)
return -ENOMEM;
+ codec->no_trigger_sense = 1;
codec->spec = spec;
spec->num_pins = ARRAY_SIZE(stac9200_pin_nids);
spec->pin_nids = stac9200_pin_nids;
if (spec == NULL)
return -ENOMEM;
+ codec->no_trigger_sense = 1;
codec->spec = spec;
spec->num_pins = ARRAY_SIZE(stac925x_pin_nids);
spec->pin_nids = stac925x_pin_nids;
if (spec == NULL)
return -ENOMEM;
+ codec->no_trigger_sense = 1;
codec->spec = spec;
codec->slave_dig_outs = stac92hd73xx_slave_dig_outs;
spec->num_pins = ARRAY_SIZE(stac92hd73xx_pin_nids);
if (spec == NULL)
return -ENOMEM;
+ codec->no_trigger_sense = 1;
codec->spec = spec;
codec->slave_dig_outs = stac92hd83xxx_slave_dig_outs;
spec->digbeep_nid = 0x21;
if (spec == NULL)
return -ENOMEM;
+ codec->no_trigger_sense = 1;
codec->spec = spec;
codec->patch_ops = stac92xx_patch_ops;
spec->num_pins = STAC92HD71BXX_NUM_PINS;
if (spec == NULL)
return -ENOMEM;
+ codec->no_trigger_sense = 1;
codec->spec = spec;
spec->num_pins = ARRAY_SIZE(stac922x_pin_nids);
spec->pin_nids = stac922x_pin_nids;
if (spec == NULL)
return -ENOMEM;
+ codec->no_trigger_sense = 1;
codec->spec = spec;
codec->slave_dig_outs = stac927x_slave_dig_outs;
spec->num_pins = ARRAY_SIZE(stac927x_pin_nids);
if (spec == NULL)
return -ENOMEM;
+ codec->no_trigger_sense = 1;
codec->spec = spec;
spec->num_pins = ARRAY_SIZE(stac9205_pin_nids);
spec->pin_nids = stac9205_pin_nids;
spec = kzalloc(sizeof(*spec), GFP_KERNEL);
if (spec == NULL)
return -ENOMEM;
+ codec->no_trigger_sense = 1;
codec->spec = spec;
spec->num_pins = ARRAY_SIZE(stac9872_pin_nids);
spec->pin_nids = stac9872_pin_nids;
LIB_H += util/include/linux/types.h
LIB_H += util/include/asm/asm-offsets.h
LIB_H += util/include/asm/bitops.h
+LIB_H += util/include/asm/bug.h
LIB_H += util/include/asm/byteorder.h
LIB_H += util/include/asm/swab.h
LIB_H += util/include/asm/system.h
LIB_H += util/include/asm/uaccess.h
LIB_H += perf.h
+LIB_H += util/cache.h
+LIB_H += util/callchain.h
+LIB_H += util/debug.h
LIB_H += util/debugfs.h
LIB_H += util/event.h
+LIB_H += util/exec_cmd.h
LIB_H += util/types.h
LIB_H += util/levenshtein.h
LIB_H += util/parse-options.h
LIB_H += util/strbuf.h
LIB_H += util/string.h
LIB_H += util/strlist.h
+LIB_H += util/svghelper.h
LIB_H += util/run-command.h
LIB_H += util/sigchain.h
LIB_H += util/symbol.h
LIB_H += util/sort.h
LIB_H += util/hist.h
LIB_H += util/thread.h
+LIB_H += util/trace-event.h
+LIB_H += util/trace-event-perl.h
LIB_H += util/probe-finder.h
LIB_H += util/probe-event.h
static char const *input_name = "perf.data";
static int force;
-static const char *const buildid_list_usage[] = {
+static const char * const buildid_list_usage[] = {
"perf buildid-list [<options>]",
NULL
};
return ret;
}
-static const char *const diff_usage[] = {
+static const char * const diff_usage[] = {
"perf diff [<options>] [old_file] [new_file]",
+ NULL,
};
static const struct option options[] = {
if (data && data->ptr == ptr) {
data->hit++;
data->bytes_req += bytes_req;
- data->bytes_alloc += bytes_req;
+ data->bytes_alloc += bytes_alloc;
} else {
data = malloc(sizeof(*data));
if (!data)
if (data && data->call_site == call_site) {
data->hit++;
data->bytes_req += bytes_req;
- data->bytes_alloc += bytes_req;
+ data->bytes_alloc += bytes_alloc;
} else {
data = malloc(sizeof(*data));
if (!data)
perf_header__write(&session->header, output, true);
}
-static int __cmd_record(int argc __used, const char **argv)
+static int __cmd_record(int argc, const char **argv)
{
int i, counter;
struct stat st;
int err;
unsigned long waking = 0;
int child_ready_pipe[2], go_pipe[2];
+ const bool forks = target_pid == -1 && argc > 0;
char buf;
page_size = sysconf(_SC_PAGE_SIZE);
signal(SIGCHLD, sig_handler);
signal(SIGINT, sig_handler);
- if (pipe(child_ready_pipe) < 0 || pipe(go_pipe) < 0) {
+ if (forks && (pipe(child_ready_pipe) < 0 || pipe(go_pipe) < 0)) {
perror("failed to create pipes");
exit(-1);
}
atexit(atexit_header);
- if (target_pid == -1) {
+ if (forks) {
pid = fork();
if (pid < 0) {
perror("failed to fork");
return err;
}
- if (!system_wide)
+ if (!system_wide && profile_cpu == -1)
event__synthesize_thread(pid, process_synthesized_event,
session);
else
/*
* Let the child rip
*/
- close(go_pipe[1]);
+ if (forks)
+ close(go_pipe[1]);
for (;;) {
int hits = samples;
argc = parse_options(argc, argv, options, record_usage,
PARSE_OPT_STOP_AT_NON_OPTION);
- if (!argc && target_pid == -1 && (!system_wide || profile_cpu == -1))
+ if (!argc && target_pid == -1 && !system_wide && profile_cpu == -1)
usage_with_options(record_usage, options);
symbol__init();
return 0;
}
-//static const char * const report_usage[] = {
-const char * const report_usage[] = {
+static const char * const report_usage[] = {
"perf report [<options>] <command>",
NULL
};
return path;
}
-static const char * const annotate_usage[] = {
+static const char * const trace_usage[] = {
"perf trace [<options>] <command>",
NULL
};
setup_scripting();
- argc = parse_options(argc, argv, options, annotate_usage,
+ argc = parse_options(argc, argv, options, trace_usage,
PARSE_OPT_STOP_AT_NON_OPTION);
if (symbol__init() < 0)
The special file descriptor is opened via the perf_event_open()
system call:
- int sys_perf_event_open(struct perf_event_hw_event *hw_event_uptr,
+ int sys_perf_event_open(struct perf_event_attr *hw_event_uptr,
pid_t pid, int cpu, int group_fd,
unsigned long flags);
Multiple counters can be kept open at a time, and the counters
can be poll()ed.
-When creating a new counter fd, 'perf_event_hw_event' is:
+When creating a new counter fd, 'perf_event_attr' is:
-struct perf_event_hw_event {
+struct perf_event_attr {
/*
* The MSB of the config word signifies if the rest contains cpu
* specific (raw) counter configuration data, if unset, the next
fcntl() managing signals.
Normally a notification is generated for every page filled, however one can
-additionally set perf_event_hw_event.wakeup_events to generate one every
+additionally set perf_event_attr.wakeup_events to generate one every
so many counter overflow events.
Future work will include a splice() interface to the ring-buffer.
struct kvm_assigned_dev_kernel *match;
struct pci_dev *dev;
- down_read(&kvm->slots_lock);
mutex_lock(&kvm->lock);
+ down_read(&kvm->slots_lock);
match = kvm_find_assigned_dev(&kvm->arch.assigned_dev_head,
assigned_dev->assigned_dev_id);
}
out:
- mutex_unlock(&kvm->lock);
up_read(&kvm->slots_lock);
+ mutex_unlock(&kvm->lock);
return r;
out_list_del:
list_del(&match->list);
pci_dev_put(dev);
out_free:
kfree(match);
- mutex_unlock(&kvm->lock);
up_read(&kvm->slots_lock);
+ mutex_unlock(&kvm->lock);
return r;
}
/*
* Ordering of locks:
*
- * kvm->slots_lock --> kvm->lock --> kvm->irq_lock
+ * kvm->lock --> kvm->slots_lock --> kvm->irq_lock
*/
DEFINE_SPINLOCK(kvm_lock);
out:
return kvm;
+#if defined(KVM_COALESCED_MMIO_PAGE_OFFSET) || \
+ (defined(CONFIG_MMU_NOTIFIER) && defined(KVM_ARCH_WANT_MMU_NOTIFIER))
out_err:
hardware_disable_all();
+#endif
out_err_nodisable:
kfree(kvm);
return ERR_PTR(r);
projects / firefly-linux-kernel-4.4.55.git / commitdiff