- pclkN, clkN: Pairs of parent of input clock and input clock to the
devices in this power domain. Maximum of 4 pairs (N = 0 to 3)
are supported currently.
+- power-domains: phandle pointing to the parent power domain, for more details
+ see Documentation/devicetree/bindings/power/power_domain.txt
Node of a device using power domains must have a power-domains property
defined with a phandle to respective power domain.
Required root node property:
compatible = "st,stih407";
+Boards with the ST STiH410 SoC shall have the following properties:
+Required root node property:
+compatible = "st,stih410";
+
Boards with the ST STiH418 SoC shall have the following properties:
Required root node property:
compatible = "st,stih418";
providing multiple PM domains (e.g. power controllers), but can be any value
as specified by device tree binding documentation of particular provider.
+Optional properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+ the power controller specified by phandle.
+ Some power domains might be powered from another power domain (or have
+ other hardware specific dependencies). For representing such dependency
+ a standard PM domain consumer binding is used. When provided, all domains
+ created by the given provider should be subdomains of the domain
+ specified by this binding. More details about power domain specifier are
+ available in the next section.
+
Example:
power: power-controller@12340000 {
The node above defines a power controller that is a PM domain provider and
expects one cell as its phandle argument.
+Example 2:
+
+ parent: power-controller@12340000 {
+ compatible = "foo,power-controller";
+ reg = <0x12340000 0x1000>;
+ #power-domain-cells = <1>;
+ };
+
+ child: power-controller@12340000 {
+ compatible = "foo,power-controller";
+ reg = <0x12341000 0x1000>;
+ power-domains = <&parent 0>;
+ #power-domain-cells = <1>;
+ };
+
+The nodes above define two power controllers: 'parent' and 'child'.
+Domains created by the 'child' power controller are subdomains of '0' power
+domain provided by the 'parent' power controller.
+
==PM domain consumers==
Required properties:
- atmel,disable : Should be present if you want to disable the watchdog.
- atmel,idle-halt : Should be present if you want to stop the watchdog when
entering idle state.
+ CAUTION: This property should be used with care, it actually makes the
+ watchdog not counting when the CPU is in idle state, therefore the
+ watchdog reset time depends on mean CPU usage and will not reset at all
+ if the CPU stop working while it is in idle state, which is probably
+ not what you want.
- atmel,dbg-halt : Should be present if you want to stop the watchdog when
entering debug state.
F: arch/arm/boot/dts/imx*
F: arch/arm/configs/imx*_defconfig
+ARM/FREESCALE VYBRID ARM ARCHITECTURE
+M: Shawn Guo <shawn.guo@linaro.org>
+M: Sascha Hauer <kernel@pengutronix.de>
+R: Stefan Agner <stefan@agner.ch>
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S: Maintained
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
+F: arch/arm/mach-imx/*vf610*
+F: arch/arm/boot/dts/vf*
+
ARM/GLOMATION GESBC9312SX MACHINE SUPPORT
M: Lennert Buytenhek <kernel@wantstofly.org>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
M: Jason Cooper <jason@lakedaemon.net>
M: Andrew Lunn <andrew@lunn.ch>
M: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
+M: Gregory Clement <gregory.clement@free-electrons.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/mach-dove/
BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
M: Christian Daudt <bcm@fixthebug.org>
-M: Matt Porter <mporter@linaro.org>
M: Florian Fainelli <f.fainelli@gmail.com>
L: bcm-kernel-feedback-list@broadcom.com
T: git git://github.com/broadcom/mach-bcm
machine-$(CONFIG_ARCH_CLPS711X) += clps711x
machine-$(CONFIG_ARCH_CNS3XXX) += cns3xxx
machine-$(CONFIG_ARCH_DAVINCI) += davinci
+machine-$(CONFIG_ARCH_DIGICOLOR) += digicolor
machine-$(CONFIG_ARCH_DOVE) += dove
machine-$(CONFIG_ARCH_EBSA110) += ebsa110
machine-$(CONFIG_ARCH_EFM32) += efm32
cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
cd-inverted;
};
+
+&aes {
+ status = "okay";
+};
+
+&sham {
+ status = "okay";
+};
&mmc1 {
vmmc-supply = <&ldo3_reg>;
};
-
-&sham {
- status = "okay";
-};
-
-&aes {
- status = "okay";
-};
dual_emac_res_vlan = <3>;
};
+&phy_sel {
+ rmii-clock-ext;
+};
+
&mac {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&cpsw_default>;
ehrpwm0_tbclk: ehrpwm0_tbclk@44e10664 {
#clock-cells = <0>;
compatible = "ti,gate-clock";
- clocks = <&dpll_per_m2_ck>;
+ clocks = <&l4ls_gclk>;
ti,bit-shift = <0>;
reg = <0x0664>;
};
ehrpwm1_tbclk: ehrpwm1_tbclk@44e10664 {
#clock-cells = <0>;
compatible = "ti,gate-clock";
- clocks = <&dpll_per_m2_ck>;
+ clocks = <&l4ls_gclk>;
ti,bit-shift = <1>;
reg = <0x0664>;
};
ehrpwm2_tbclk: ehrpwm2_tbclk@44e10664 {
#clock-cells = <0>;
compatible = "ti,gate-clock";
- clocks = <&dpll_per_m2_ck>;
+ clocks = <&l4ls_gclk>;
ti,bit-shift = <2>;
reg = <0x0664>;
};
ehrpwm0_tbclk: ehrpwm0_tbclk {
#clock-cells = <0>;
compatible = "ti,gate-clock";
- clocks = <&dpll_per_m2_ck>;
+ clocks = <&l4ls_gclk>;
ti,bit-shift = <0>;
reg = <0x0664>;
};
ehrpwm1_tbclk: ehrpwm1_tbclk {
#clock-cells = <0>;
compatible = "ti,gate-clock";
- clocks = <&dpll_per_m2_ck>;
+ clocks = <&l4ls_gclk>;
ti,bit-shift = <1>;
reg = <0x0664>;
};
ehrpwm2_tbclk: ehrpwm2_tbclk {
#clock-cells = <0>;
compatible = "ti,gate-clock";
- clocks = <&dpll_per_m2_ck>;
+ clocks = <&l4ls_gclk>;
ti,bit-shift = <2>;
reg = <0x0664>;
};
ehrpwm3_tbclk: ehrpwm3_tbclk {
#clock-cells = <0>;
compatible = "ti,gate-clock";
- clocks = <&dpll_per_m2_ck>;
+ clocks = <&l4ls_gclk>;
ti,bit-shift = <4>;
reg = <0x0664>;
};
ehrpwm4_tbclk: ehrpwm4_tbclk {
#clock-cells = <0>;
compatible = "ti,gate-clock";
- clocks = <&dpll_per_m2_ck>;
+ clocks = <&l4ls_gclk>;
ti,bit-shift = <5>;
reg = <0x0664>;
};
ehrpwm5_tbclk: ehrpwm5_tbclk {
#clock-cells = <0>;
compatible = "ti,gate-clock";
- clocks = <&dpll_per_m2_ck>;
+ clocks = <&l4ls_gclk>;
ti,bit-shift = <6>;
reg = <0x0664>;
};
pinctrl_usart3_rts: usart3_rts-0 {
atmel,pins =
- <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC8 periph B */
+ <AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_NONE>;
};
pinctrl_usart3_cts: usart3_cts-0 {
atmel,pins =
- <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC10 periph B */
+ <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
};
};
};
usb1: gadget@fffa4000 {
- compatible = "atmel,at91rm9200-udc";
+ compatible = "atmel,at91sam9260-udc";
reg = <0xfffa4000 0x4000>;
interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>;
clocks = <&udc_clk>, <&udpck>;
atmel,watchdog-type = "hardware";
atmel,reset-type = "all";
atmel,dbg-halt;
- atmel,idle-halt;
status = "disabled";
};
};
usb1: gadget@fffa4000 {
- compatible = "atmel,at91rm9200-udc";
+ compatible = "atmel,at91sam9261-udc";
reg = <0xfffa4000 0x4000>;
interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>;
- clocks = <&usb>, <&udc_clk>, <&udpck>;
- clock-names = "usb_clk", "udc_clk", "udpck";
+ clocks = <&udc_clk>, <&udpck>;
+ clock-names = "pclk", "hclk";
+ atmel,matrix = <&matrix>;
status = "disabled";
};
};
matrix: matrix@ffffee00 {
- compatible = "atmel,at91sam9260-bus-matrix";
+ compatible = "atmel,at91sam9260-bus-matrix", "syscon";
reg = <0xffffee00 0x200>;
};
sram1: sram@00500000 {
compatible = "mmio-sram";
- reg = <0x00300000 0x4000>;
+ reg = <0x00500000 0x4000>;
};
ahb {
};
usb1: gadget@fff78000 {
- compatible = "atmel,at91rm9200-udc";
+ compatible = "atmel,at91sam9263-udc";
reg = <0xfff78000 0x4000>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH 2>;
clocks = <&udc_clk>, <&udpck>;
atmel,watchdog-type = "hardware";
atmel,reset-type = "all";
atmel,dbg-halt;
- atmel,idle-halt;
status = "disabled";
};
atmel,watchdog-type = "hardware";
atmel,reset-type = "all";
atmel,dbg-halt;
- atmel,idle-halt;
status = "disabled";
};
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00800000 0x100000>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
- clocks = <&usb>, <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+ clocks = <&utmi>, <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
clock-names = "usb_clk", "ehci_clk", "hclk", "uhpck";
status = "disabled";
};
atmel,watchdog-type = "hardware";
atmel,reset-type = "all";
atmel,dbg-halt;
- atmel,idle-halt;
status = "disabled";
};
reg = <0x00500000 0x80000
0xf803c000 0x400>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 0>;
- clocks = <&usb>, <&udphs_clk>;
+ clocks = <&utmi>, <&udphs_clk>;
clock-names = "hclk", "pclk";
status = "disabled";
atmel,watchdog-type = "hardware";
atmel,reset-type = "all";
atmel,dbg-halt;
- atmel,idle-halt;
status = "disabled";
};
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00700000 0x100000>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
- clocks = <&usb>, <&uhphs_clk>, <&uhpck>;
+ clocks = <&utmi>, <&uhphs_clk>, <&uhpck>;
clock-names = "usb_clk", "ehci_clk", "uhpck";
status = "disabled";
};
dcan1_pins_default: dcan1_pins_default {
pinctrl-single,pins = <
- 0x3d0 (PIN_OUTPUT | MUX_MODE0) /* dcan1_tx */
- 0x3d4 (MUX_MODE15) /* dcan1_rx.off */
- 0x418 (PULL_DIS | MUX_MODE1) /* wakeup0.dcan1_rx */
+ 0x3d0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
+ 0x418 (PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
>;
};
dcan1_pins_sleep: dcan1_pins_sleep {
pinctrl-single,pins = <
- 0x3d0 (MUX_MODE15) /* dcan1_tx.off */
- 0x3d4 (MUX_MODE15) /* dcan1_rx.off */
- 0x418 (MUX_MODE15) /* wakeup0.off */
+ 0x3d0 (MUX_MODE15 | PULL_UP) /* dcan1_tx.off */
+ 0x418 (MUX_MODE15 | PULL_UP) /* wakeup0.off */
>;
};
};
dcan1_pins_default: dcan1_pins_default {
pinctrl-single,pins = <
- 0x3d0 (PIN_OUTPUT | MUX_MODE0) /* dcan1_tx */
- 0x3d4 (MUX_MODE15) /* dcan1_rx.off */
- 0x418 (PULL_DIS | MUX_MODE1) /* wakeup0.dcan1_rx */
+ 0x3d0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
+ 0x418 (PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
>;
};
dcan1_pins_sleep: dcan1_pins_sleep {
pinctrl-single,pins = <
- 0x3d0 (MUX_MODE15) /* dcan1_tx.off */
- 0x3d4 (MUX_MODE15) /* dcan1_rx.off */
- 0x418 (MUX_MODE15) /* wakeup0.off */
+ 0x3d0 (MUX_MODE15 | PULL_UP) /* dcan1_tx.off */
+ 0x418 (MUX_MODE15 | PULL_UP) /* wakeup0.off */
>;
};
ti,invert-autoidle-bit;
};
+ dpll_core_byp_mux: dpll_core_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+ ti,bit-shift = <23>;
+ reg = <0x012c>;
+ };
+
dpll_core_ck: dpll_core_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-core-clock";
- clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+ clocks = <&sys_clkin1>, <&dpll_core_byp_mux>;
reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
};
clock-div = <1>;
};
+ dpll_dsp_byp_mux: dpll_dsp_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin1>, <&dsp_dpll_hs_clk_div>;
+ ti,bit-shift = <23>;
+ reg = <0x0240>;
+ };
+
dpll_dsp_ck: dpll_dsp_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-clock";
- clocks = <&sys_clkin1>, <&dsp_dpll_hs_clk_div>;
+ clocks = <&sys_clkin1>, <&dpll_dsp_byp_mux>;
reg = <0x0234>, <0x0238>, <0x0240>, <0x023c>;
};
clock-div = <1>;
};
+ dpll_iva_byp_mux: dpll_iva_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin1>, <&iva_dpll_hs_clk_div>;
+ ti,bit-shift = <23>;
+ reg = <0x01ac>;
+ };
+
dpll_iva_ck: dpll_iva_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-clock";
- clocks = <&sys_clkin1>, <&iva_dpll_hs_clk_div>;
+ clocks = <&sys_clkin1>, <&dpll_iva_byp_mux>;
reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
};
clock-div = <1>;
};
+ dpll_gpu_byp_mux: dpll_gpu_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+ ti,bit-shift = <23>;
+ reg = <0x02e4>;
+ };
+
dpll_gpu_ck: dpll_gpu_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-clock";
- clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+ clocks = <&sys_clkin1>, <&dpll_gpu_byp_mux>;
reg = <0x02d8>, <0x02dc>, <0x02e4>, <0x02e0>;
};
clock-div = <1>;
};
+ dpll_ddr_byp_mux: dpll_ddr_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+ ti,bit-shift = <23>;
+ reg = <0x021c>;
+ };
+
dpll_ddr_ck: dpll_ddr_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-clock";
- clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+ clocks = <&sys_clkin1>, <&dpll_ddr_byp_mux>;
reg = <0x0210>, <0x0214>, <0x021c>, <0x0218>;
};
ti,invert-autoidle-bit;
};
+ dpll_gmac_byp_mux: dpll_gmac_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+ ti,bit-shift = <23>;
+ reg = <0x02b4>;
+ };
+
dpll_gmac_ck: dpll_gmac_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-clock";
- clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+ clocks = <&sys_clkin1>, <&dpll_gmac_byp_mux>;
reg = <0x02a8>, <0x02ac>, <0x02b4>, <0x02b0>;
};
clock-div = <1>;
};
+ dpll_eve_byp_mux: dpll_eve_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin1>, <&eve_dpll_hs_clk_div>;
+ ti,bit-shift = <23>;
+ reg = <0x0290>;
+ };
+
dpll_eve_ck: dpll_eve_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-clock";
- clocks = <&sys_clkin1>, <&eve_dpll_hs_clk_div>;
+ clocks = <&sys_clkin1>, <&dpll_eve_byp_mux>;
reg = <0x0284>, <0x0288>, <0x0290>, <0x028c>;
};
clock-div = <1>;
};
+ dpll_per_byp_mux: dpll_per_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin1>, <&per_dpll_hs_clk_div>;
+ ti,bit-shift = <23>;
+ reg = <0x014c>;
+ };
+
dpll_per_ck: dpll_per_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-clock";
- clocks = <&sys_clkin1>, <&per_dpll_hs_clk_div>;
+ clocks = <&sys_clkin1>, <&dpll_per_byp_mux>;
reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
};
clock-div = <1>;
};
+ dpll_usb_byp_mux: dpll_usb_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin1>, <&usb_dpll_hs_clk_div>;
+ ti,bit-shift = <23>;
+ reg = <0x018c>;
+ };
+
dpll_usb_ck: dpll_usb_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-j-type-clock";
- clocks = <&sys_clkin1>, <&usb_dpll_hs_clk_div>;
+ clocks = <&sys_clkin1>, <&dpll_usb_byp_mux>;
reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
};
*/
#include "skeleton.dtsi"
+#include "exynos4-cpu-thermal.dtsi"
#include <dt-bindings/clock/exynos3250.h>
/ {
interrupts = <0 216 0>;
clocks = <&cmu CLK_TMU_APBIF>;
clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
status = "disabled";
};
--- /dev/null
+/*
+ * Device tree sources for Exynos4 thermal zone
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+thermal-zones {
+ cpu_thermal: cpu-thermal {
+ thermal-sensors = <&tmu 0>;
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ trips {
+ cpu_alert0: cpu-alert-0 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <10000>; /* millicelsius */
+ type = "active";
+ };
+ cpu_alert1: cpu-alert-1 {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <10000>; /* millicelsius */
+ type = "active";
+ };
+ cpu_alert2: cpu-alert-2 {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <10000>; /* millicelsius */
+ type = "active";
+ };
+ cpu_crit0: cpu-crit-0 {
+ temperature = <120000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ };
+ map1 {
+ trip = <&cpu_alert1>;
+ };
+ };
+ };
+};
+};
i2c5 = &i2c_5;
i2c6 = &i2c_6;
i2c7 = &i2c_7;
+ i2c8 = &i2c_8;
csis0 = &csis_0;
csis1 = &csis_1;
fimc0 = &fimc_0;
compatible = "samsung,exynos4210-pd";
reg = <0x10023C20 0x20>;
#power-domain-cells = <0>;
+ power-domains = <&pd_lcd0>;
};
pd_cam: cam-power-domain@10023C00 {
status = "disabled";
};
+ i2c_8: i2c@138E0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-hdmiphy-i2c";
+ reg = <0x138E0000 0x100>;
+ interrupts = <0 93 0>;
+ clocks = <&clock CLK_I2C_HDMI>;
+ clock-names = "i2c";
+ status = "disabled";
+
+ hdmi_i2c_phy: hdmiphy@38 {
+ compatible = "exynos4210-hdmiphy";
+ reg = <0x38>;
+ };
+ };
+
spi_0: spi@13920000 {
compatible = "samsung,exynos4210-spi";
reg = <0x13920000 0x100>;
status = "disabled";
};
+ tmu: tmu@100C0000 {
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
+
+ hdmi: hdmi@12D00000 {
+ compatible = "samsung,exynos4210-hdmi";
+ reg = <0x12D00000 0x70000>;
+ interrupts = <0 92 0>;
+ clock-names = "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy",
+ "mout_hdmi";
+ clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
+ <&clock CLK_SCLK_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
+ <&clock CLK_MOUT_HDMI>;
+ phy = <&hdmi_i2c_phy>;
+ power-domains = <&pd_tv>;
+ samsung,syscon-phandle = <&pmu_system_controller>;
+ status = "disabled";
+ };
+
+ mixer: mixer@12C10000 {
+ compatible = "samsung,exynos4210-mixer";
+ interrupts = <0 91 0>;
+ reg = <0x12C10000 0x2100>, <0x12c00000 0x300>;
+ power-domains = <&pd_tv>;
+ status = "disabled";
+ };
+
ppmu_dmc0: ppmu_dmc0@106a0000 {
compatible = "samsung,exynos-ppmu";
reg = <0x106a0000 0x2000>;
status = "okay";
};
+ tmu@100C0000 {
+ status = "okay";
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 2 2>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 4 4>;
+ };
+ };
+ };
+ };
+
camera {
pinctrl-names = "default";
pinctrl-0 = <>;
assigned-clock-rates = <0>, <160000000>;
};
};
+
+ hdmi_en: voltage-regulator-hdmi-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "HDMI_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpe0 1 0>;
+ enable-active-high;
+ };
+
+ hdmi_ddc: i2c-ddc {
+ compatible = "i2c-gpio";
+ gpios = <&gpe4 2 0 &gpe4 3 0>;
+ i2c-gpio,delay-us = <100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&i2c_ddc_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ mixer@12C10000 {
+ status = "okay";
+ };
+
+ hdmi@12D00000 {
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd>;
+ hdmi-en-supply = <&hdmi_en>;
+ vdd-supply = <&ldo3_reg>;
+ vdd_osc-supply = <&ldo4_reg>;
+ vdd_pll-supply = <&ldo3_reg>;
+ ddc = <&hdmi_ddc>;
+ status = "okay";
+ };
+
+ i2c@138E0000 {
+ status = "okay";
+ };
+};
+
+&pinctrl_1 {
+ hdmi_hpd: hdmi-hpd {
+ samsung,pins = "gpx3-7";
+ samsung,pin-pud = <0>;
+ };
+};
+
+&pinctrl_0 {
+ i2c_ddc_bus: i2c-ddc-bus {
+ samsung,pins = "gpe4-2", "gpe4-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
};
&mdma1 {
#include "exynos4.dtsi"
#include "exynos4210-pinctrl.dtsi"
+#include "exynos4-cpu-thermal.dtsi"
/ {
compatible = "samsung,exynos4210", "samsung,exynos4";
#address-cells = <1>;
#size-cells = <0>;
- cpu@900 {
+ cpu0: cpu@900 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <0x900>;
+ cooling-min-level = <4>;
+ cooling-max-level = <2>;
+ #cooling-cells = <2>; /* min followed by max */
};
cpu@901 {
reg = <0x03860000 0x1000>;
};
- tmu@100C0000 {
+ tmu: tmu@100C0000 {
compatible = "samsung,exynos4210-tmu";
interrupt-parent = <&combiner>;
reg = <0x100C0000 0x100>;
interrupts = <2 4>;
clocks = <&clock CLK_TMU_APBIF>;
clock-names = "tmu_apbif";
+ samsung,tmu_gain = <15>;
+ samsung,tmu_reference_voltage = <7>;
status = "disabled";
};
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tmu 0>;
+
+ trips {
+ cpu_alert0: cpu-alert-0 {
+ temperature = <85000>; /* millicelsius */
+ };
+ cpu_alert1: cpu-alert-1 {
+ temperature = <100000>; /* millicelsius */
+ };
+ cpu_alert2: cpu-alert-2 {
+ temperature = <110000>; /* millicelsius */
+ };
+ };
+ };
+ };
+
g2d@12800000 {
compatible = "samsung,s5pv210-g2d";
reg = <0x12800000 0x1000>;
};
};
+ mixer: mixer@12C10000 {
+ clock-names = "mixer", "hdmi", "sclk_hdmi", "vp", "mout_mixer",
+ "sclk_mixer";
+ clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+ <&clock CLK_SCLK_HDMI>, <&clock CLK_VP>,
+ <&clock CLK_MOUT_MIXER>, <&clock CLK_SCLK_MIXER>;
+ };
+
ppmu_lcd1: ppmu_lcd1@12240000 {
compatible = "samsung,exynos-ppmu";
reg = <0x12240000 0x2000>;
#address-cells = <1>;
#size-cells = <0>;
- cpu@A00 {
+ cpu0: cpu@A00 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <0xA00>;
+ cooling-min-level = <13>;
+ cooling-max-level = <7>;
+ #cooling-cells = <2>; /* min followed by max */
};
cpu@A01 {
regulator-always-on;
};
+ ldo8_reg: ldo@8 {
+ regulator-compatible = "LDO8";
+ regulator-name = "VDD10_HDMI_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo10_reg: ldo@10 {
+ regulator-compatible = "LDO10";
+ regulator-name = "VDDQ_MIPIHSI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
ldo11_reg: LDO11 {
regulator-name = "VDD18_ABB1_1.8V";
regulator-min-microvolt = <1800000>;
ehci: ehci@12580000 {
status = "okay";
};
+
+ tmu@100C0000 {
+ vtmu-supply = <&ldo10_reg>;
+ status = "okay";
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 7 7>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 13 13>;
+ };
+ };
+ };
+ };
+
+ mixer: mixer@12C10000 {
+ status = "okay";
+ };
+
+ hdmi@12D00000 {
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd>;
+ vdd-supply = <&ldo8_reg>;
+ vdd_osc-supply = <&ldo10_reg>;
+ vdd_pll-supply = <&ldo8_reg>;
+ ddc = <&hdmi_ddc>;
+ status = "okay";
+ };
+
+ hdmi_ddc: i2c@13880000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+ };
+
+ i2c@138E0000 {
+ status = "okay";
+ };
};
&pinctrl_1 {
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
+
+ hdmi_hpd: hdmi-hpd {
+ samsung,pins = "gpx3-7";
+ samsung,pin-pud = <1>;
+ };
};
--- /dev/null
+/*
+ * Device tree sources for Exynos4412 TMU sensor configuration
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <dt-bindings/thermal/thermal_exynos.h>
+
+#thermal-sensor-cells = <0>;
+samsung,tmu_gain = <8>;
+samsung,tmu_reference_voltage = <16>;
+samsung,tmu_noise_cancel_mode = <4>;
+samsung,tmu_efuse_value = <55>;
+samsung,tmu_min_efuse_value = <40>;
+samsung,tmu_max_efuse_value = <100>;
+samsung,tmu_first_point_trim = <25>;
+samsung,tmu_second_point_trim = <85>;
+samsung,tmu_default_temp_offset = <50>;
+samsung,tmu_cal_type = <TYPE_ONE_POINT_TRIMMING>;
pulldown-ohm = <100000>; /* 100K */
io-channels = <&adc 2>; /* Battery temperature */
};
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 7 7>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 13 13>;
+ };
+ };
+ };
+ };
};
&pmu_system_controller {
#address-cells = <1>;
#size-cells = <0>;
- cpu@A00 {
+ cpu0: cpu@A00 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <0xA00>;
+ cooling-min-level = <13>;
+ cooling-max-level = <7>;
+ #cooling-cells = <2>; /* min followed by max */
};
cpu@A01 {
#include "exynos4.dtsi"
#include "exynos4x12-pinctrl.dtsi"
+#include "exynos4-cpu-thermal.dtsi"
/ {
aliases {
clock-names = "tmu_apbif";
status = "disabled";
};
+
+ hdmi: hdmi@12D00000 {
+ compatible = "samsung,exynos4212-hdmi";
+ };
+
+ mixer: mixer@12C10000 {
+ compatible = "samsung,exynos4212-mixer";
+ clock-names = "mixer", "hdmi", "sclk_hdmi", "vp";
+ clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+ <&clock CLK_SCLK_HDMI>, <&clock CLK_VP>;
+ };
};
#include <dt-bindings/clock/exynos5250.h>
#include "exynos5.dtsi"
#include "exynos5250-pinctrl.dtsi"
-
+#include "exynos4-cpu-thermal.dtsi"
#include <dt-bindings/clock/exynos-audss-clk.h>
/ {
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0>;
clock-frequency = <1700000000>;
+ cooling-min-level = <15>;
+ cooling-max-level = <9>;
+ #cooling-cells = <2>; /* min followed by max */
};
cpu@1 {
device_type = "cpu";
#power-domain-cells = <0>;
};
+ pd_disp1: disp1-power-domain@100440A0 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x100440A0 0x20>;
+ #power-domain-cells = <0>;
+ };
+
clock: clock-controller@10010000 {
compatible = "samsung,exynos5250-clock";
reg = <0x10010000 0x30000>;
status = "disabled";
};
- tmu@10060000 {
+ tmu: tmu@10060000 {
compatible = "samsung,exynos5250-tmu";
reg = <0x10060000 0x100>;
interrupts = <0 65 0>;
clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tmu 0>;
+
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 9 9>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 15 15>;
+ };
+ };
+ };
};
serial@12C00000 {
hdmi: hdmi {
compatible = "samsung,exynos4212-hdmi";
reg = <0x14530000 0x70000>;
+ power-domains = <&pd_disp1>;
interrupts = <0 95 0>;
clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
<&clock CLK_SCLK_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
mixer {
compatible = "samsung,exynos5250-mixer";
reg = <0x14450000 0x10000>;
+ power-domains = <&pd_disp1>;
interrupts = <0 94 0>;
- clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>;
- clock-names = "mixer", "sclk_hdmi";
+ clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+ <&clock CLK_SCLK_HDMI>;
+ clock-names = "mixer", "hdmi", "sclk_hdmi";
};
dp_phy: video-phy@10040720 {
};
dp: dp-controller@145B0000 {
+ power-domains = <&pd_disp1>;
clocks = <&clock CLK_DP>;
clock-names = "dp";
phys = <&dp_phy>;
};
fimd: fimd@14400000 {
+ power-domains = <&pd_disp1>;
clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
clock-names = "sclk_fimd", "fimd";
};
--- /dev/null
+/*
+ * Device tree sources for default Exynos5420 thermal zone definition
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+polling-delay-passive = <0>;
+polling-delay = <0>;
+trips {
+ cpu-alert-0 {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <10000>; /* millicelsius */
+ type = "active";
+ };
+ cpu-alert-1 {
+ temperature = <103000>; /* millicelsius */
+ hysteresis = <10000>; /* millicelsius */
+ type = "active";
+ };
+ cpu-alert-2 {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <10000>; /* millicelsius */
+ type = "active";
+ };
+ cpu-crit-0 {
+ temperature = <1200000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+};
compatible = "samsung,exynos5420-mixer";
reg = <0x14450000 0x10000>;
interrupts = <0 94 0>;
- clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>;
- clock-names = "mixer", "sclk_hdmi";
+ clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+ <&clock CLK_SCLK_HDMI>;
+ clock-names = "mixer", "hdmi", "sclk_hdmi";
power-domains = <&disp_pd>;
};
interrupts = <0 65 0>;
clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
};
tmu_cpu1: tmu@10064000 {
interrupts = <0 183 0>;
clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
};
tmu_cpu2: tmu@10068000 {
interrupts = <0 184 0>;
clocks = <&clock CLK_TMU>, <&clock CLK_TMU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
};
tmu_cpu3: tmu@1006c000 {
interrupts = <0 185 0>;
clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
};
tmu_gpu: tmu@100a0000 {
interrupts = <0 215 0>;
clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+ #include "exynos4412-tmu-sensor-conf.dtsi"
+ };
+
+ thermal-zones {
+ cpu0_thermal: cpu0-thermal {
+ thermal-sensors = <&tmu_cpu0>;
+ #include "exynos5420-trip-points.dtsi"
+ };
+ cpu1_thermal: cpu1-thermal {
+ thermal-sensors = <&tmu_cpu1>;
+ #include "exynos5420-trip-points.dtsi"
+ };
+ cpu2_thermal: cpu2-thermal {
+ thermal-sensors = <&tmu_cpu2>;
+ #include "exynos5420-trip-points.dtsi"
+ };
+ cpu3_thermal: cpu3-thermal {
+ thermal-sensors = <&tmu_cpu3>;
+ #include "exynos5420-trip-points.dtsi"
+ };
+ gpu_thermal: gpu-thermal {
+ thermal-sensors = <&tmu_gpu>;
+ #include "exynos5420-trip-points.dtsi"
+ };
};
watchdog: watchdog@101D0000 {
--- /dev/null
+/*
+ * Device tree sources for Exynos5440 TMU sensor configuration
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <dt-bindings/thermal/thermal_exynos.h>
+
+#thermal-sensor-cells = <0>;
+samsung,tmu_gain = <5>;
+samsung,tmu_reference_voltage = <16>;
+samsung,tmu_noise_cancel_mode = <4>;
+samsung,tmu_efuse_value = <0x5d2d>;
+samsung,tmu_min_efuse_value = <16>;
+samsung,tmu_max_efuse_value = <76>;
+samsung,tmu_first_point_trim = <25>;
+samsung,tmu_second_point_trim = <70>;
+samsung,tmu_default_temp_offset = <25>;
+samsung,tmu_cal_type = <TYPE_ONE_POINT_TRIMMING>;
--- /dev/null
+/*
+ * Device tree sources for default Exynos5440 thermal zone definition
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+polling-delay-passive = <0>;
+polling-delay = <0>;
+trips {
+ cpu-alert-0 {
+ temperature = <100000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "active";
+ };
+ cpu-crit-0 {
+ temperature = <1050000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+};
interrupts = <0 58 0>;
clocks = <&clock CLK_B_125>;
clock-names = "tmu_apbif";
+ #include "exynos5440-tmu-sensor-conf.dtsi"
};
tmuctrl_1: tmuctrl@16011C {
interrupts = <0 58 0>;
clocks = <&clock CLK_B_125>;
clock-names = "tmu_apbif";
+ #include "exynos5440-tmu-sensor-conf.dtsi"
};
tmuctrl_2: tmuctrl@160120 {
interrupts = <0 58 0>;
clocks = <&clock CLK_B_125>;
clock-names = "tmu_apbif";
+ #include "exynos5440-tmu-sensor-conf.dtsi"
+ };
+
+ thermal-zones {
+ cpu0_thermal: cpu0-thermal {
+ thermal-sensors = <&tmuctrl_0>;
+ #include "exynos5440-trip-points.dtsi"
+ };
+ cpu1_thermal: cpu1-thermal {
+ thermal-sensors = <&tmuctrl_1>;
+ #include "exynos5440-trip-points.dtsi"
+ };
+ cpu2_thermal: cpu2-thermal {
+ thermal-sensors = <&tmuctrl_2>;
+ #include "exynos5440-trip-points.dtsi"
+ };
};
sata@210000 {
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 22 0>;
enable-active-high;
+ vin-supply = <&swbst_reg>;
};
reg_usb_h1_vbus: regulator@1 {
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 29 0>;
enable-active-high;
+ vin-supply = <&swbst_reg>;
};
reg_audio: regulator@2 {
regulator-max-microvolt = <5000000>;
gpio = <&gpio4 0 0>;
enable-active-high;
+ vin-supply = <&swbst_reg>;
};
reg_usb_otg2_vbus: regulator@1 {
regulator-max-microvolt = <5000000>;
gpio = <&gpio4 2 0>;
enable-active-high;
+ vin-supply = <&swbst_reg>;
};
reg_aud3v: regulator@2 {
core_thermal: core_thermal {
polling-delay-passive = <250>; /* milliseconds */
- polling-delay = <1000>; /* milliseconds */
+ polling-delay = <500>; /* milliseconds */
/* sensor ID */
thermal-sensors = <&bandgap 2>;
gpu_thermal: gpu_thermal {
polling-delay-passive = <250>; /* milliseconds */
- polling-delay = <1000>; /* milliseconds */
+ polling-delay = <500>; /* milliseconds */
/* sensor ID */
thermal-sensors = <&bandgap 1>;
};
};
+&cpu_thermal {
+ polling-delay = <500>; /* milliseconds */
+};
+
/include/ "omap54xx-clocks.dtsi"
ti,index-starts-at-one;
};
+ dpll_core_byp_mux: dpll_core_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin>, <&dpll_abe_m3x2_ck>;
+ ti,bit-shift = <23>;
+ reg = <0x012c>;
+ };
+
dpll_core_ck: dpll_core_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-core-clock";
- clocks = <&sys_clkin>, <&dpll_abe_m3x2_ck>;
+ clocks = <&sys_clkin>, <&dpll_core_byp_mux>;
reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
};
clock-div = <1>;
};
+ dpll_iva_byp_mux: dpll_iva_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin>, <&iva_dpll_hs_clk_div>;
+ ti,bit-shift = <23>;
+ reg = <0x01ac>;
+ };
+
dpll_iva_ck: dpll_iva_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-clock";
- clocks = <&sys_clkin>, <&iva_dpll_hs_clk_div>;
+ clocks = <&sys_clkin>, <&dpll_iva_byp_mux>;
reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
};
};
};
&cm_core_clocks {
+
+ dpll_per_byp_mux: dpll_per_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin>, <&per_dpll_hs_clk_div>;
+ ti,bit-shift = <23>;
+ reg = <0x014c>;
+ };
+
dpll_per_ck: dpll_per_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-clock";
- clocks = <&sys_clkin>, <&per_dpll_hs_clk_div>;
+ clocks = <&sys_clkin>, <&dpll_per_byp_mux>;
reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
};
ti,index-starts-at-one;
};
+ dpll_usb_byp_mux: dpll_usb_byp_mux {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin>, <&usb_dpll_hs_clk_div>;
+ ti,bit-shift = <23>;
+ reg = <0x018c>;
+ };
+
dpll_usb_ck: dpll_usb_ck {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-j-type-clock";
- clocks = <&sys_clkin>, <&usb_dpll_hs_clk_div>;
+ clocks = <&sys_clkin>, <&dpll_usb_byp_mux>;
reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
};
atmel,watchdog-type = "hardware";
atmel,reset-type = "all";
atmel,dbg-halt;
- atmel,idle-halt;
status = "disabled";
};
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00700000 0x100000>;
interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>;
- clocks = <&usb>, <&uhphs_clk>, <&uhpck>;
+ clocks = <&utmi>, <&uhphs_clk>, <&uhpck>;
clock-names = "usb_clk", "ehci_clk", "uhpck";
status = "disabled";
};
gpio4 = &pioE;
tcb0 = &tcb0;
tcb1 = &tcb1;
+ i2c0 = &i2c0;
i2c2 = &i2c2;
};
cpus {
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00600000 0x100000>;
interrupts = <46 IRQ_TYPE_LEVEL_HIGH 2>;
- clocks = <&usb>, <&uhphs_clk>, <&uhpck>;
+ clocks = <&utmi>, <&uhphs_clk>, <&uhpck>;
clock-names = "usb_clk", "ehci_clk", "uhpck";
status = "disabled";
};
lcdck: lcdck {
#clock-cells = <0>;
- reg = <4>;
- clocks = <&smd>;
+ reg = <3>;
+ clocks = <&mck>;
};
smdck: smdck {
reg = <50>;
};
- lcd_clk: lcd_clk {
+ lcdc_clk: lcdc_clk {
#clock-cells = <0>;
reg = <51>;
};
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&l4_sp_clk>;
+ dmas = <&pdma 28>,
+ <&pdma 29>;
+ dma-names = "tx", "rx";
};
uart1: serial1@ffc03000 {
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&l4_sp_clk>;
+ dmas = <&pdma 30>,
+ <&pdma 31>;
+ dma-names = "tx", "rx";
};
rst: rstmgr@ffd05000 {
CONFIG_BLK_DEV_SD=y
# CONFIG_SCSI_LOWLEVEL is not set
CONFIG_NETDEVICES=y
+CONFIG_ARM_AT91_ETHER=y
CONFIG_MACB=y
# CONFIG_NET_VENDOR_BROADCOM is not set
CONFIG_DM9000=y
CONFIG_PCI_RCAR_GEN2_PCIE=y
CONFIG_PCIEPORTBUS=y
CONFIG_SMP=y
-CONFIG_NR_CPUS=8
+CONFIG_NR_CPUS=16
CONFIG_HIGHPTE=y
CONFIG_CMA=y
CONFIG_ARM_APPENDED_DTB=y
CONFIG_PWM_TWL_LED=m
CONFIG_OMAP_USB2=m
CONFIG_TI_PIPE3=y
+CONFIG_TWL4030_USB=m
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_SYSVIPC=y
CONFIG_IRQ_DOMAIN_DEBUG=y
CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_EMBEDDED=y
CONFIG_SLAB=y
CONFIG_PERF_EVENTS=y
CONFIG_ARCH_SUNXI=y
CONFIG_SMP=y
+CONFIG_NR_CPUS=8
CONFIG_AEABI=y
CONFIG_HIGHMEM=y
CONFIG_HIGHPTE=y
CONFIG_USB=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_MON=y
-CONFIG_USB_ISP1760_HCD=y
CONFIG_USB_STORAGE=y
+CONFIG_USB_ISP1760=y
CONFIG_MMC=y
CONFIG_MMC_ARMMMCI=y
CONFIG_NEW_LEDS=y
#define AT91_DBGU 0xfc00c000 /* SAMA5D4_BASE_USART3 */
#endif
-/* Keep in sync with mach-at91/include/mach/hardware.h */
+#ifdef CONFIG_MMU
#define AT91_IO_P2V(x) ((x) - 0x01000000)
+#else
+#define AT91_IO_P2V(x) (x)
+#endif
#define AT91_DBGU_SR (0x14) /* Status Register */
#define AT91_DBGU_THR (0x1c) /* Transmitter Holding Register */
phys_addr_t sram_pbase;
unsigned long sram_base;
struct device_node *node;
- struct platform_device *pdev;
+ struct platform_device *pdev = NULL;
- node = of_find_compatible_node(NULL, NULL, "mmio-sram");
- if (!node) {
- pr_warn("%s: failed to find sram node!\n", __func__);
- return;
+ for_each_compatible_node(node, NULL, "mmio-sram") {
+ pdev = of_find_device_by_node(node);
+ if (pdev) {
+ of_node_put(node);
+ break;
+ }
}
- pdev = of_find_device_by_node(node);
if (!pdev) {
pr_warn("%s: failed to find sram device!\n", __func__);
- goto put_node;
+ return;
}
sram_pool = dev_get_gen_pool(&pdev->dev);
if (!sram_pool) {
pr_warn("%s: sram pool unavailable!\n", __func__);
- goto put_node;
+ return;
}
sram_base = gen_pool_alloc(sram_pool, at91_slow_clock_sz);
if (!sram_base) {
pr_warn("%s: unable to alloc ocram!\n", __func__);
- goto put_node;
+ return;
}
sram_pbase = gen_pool_virt_to_phys(sram_pool, sram_base);
slow_clock = __arm_ioremap_exec(sram_pbase, at91_slow_clock_sz, false);
-
-put_node:
- of_node_put(node);
}
#endif
" mcr p15, 0, %0, c7, c0, 4\n\t"
" str %5, [%1, %2]"
:
- : "r" (0), "r" (AT91_BASE_SYS), "r" (AT91RM9200_SDRAMC_LPR),
+ : "r" (0), "r" (at91_ramc_base[0]), "r" (AT91RM9200_SDRAMC_LPR),
"r" (1), "r" (AT91RM9200_SDRAMC_SRR),
"r" (lpr));
}
*/
#undef SLOWDOWN_MASTER_CLOCK
-#define MCKRDY_TIMEOUT 1000
-#define MOSCRDY_TIMEOUT 1000
-#define PLLALOCK_TIMEOUT 1000
-#define PLLBLOCK_TIMEOUT 1000
-
pmc .req r0
sdramc .req r1
ramc1 .req r2
* Wait until master clock is ready (after switching master clock source)
*/
.macro wait_mckrdy
- mov tmp2, #MCKRDY_TIMEOUT
-1: sub tmp2, tmp2, #1
- cmp tmp2, #0
- beq 2f
- ldr tmp1, [pmc, #AT91_PMC_SR]
+1: ldr tmp1, [pmc, #AT91_PMC_SR]
tst tmp1, #AT91_PMC_MCKRDY
beq 1b
-2:
.endm
/*
* Wait until master oscillator has stabilized.
*/
.macro wait_moscrdy
- mov tmp2, #MOSCRDY_TIMEOUT
-1: sub tmp2, tmp2, #1
- cmp tmp2, #0
- beq 2f
- ldr tmp1, [pmc, #AT91_PMC_SR]
+1: ldr tmp1, [pmc, #AT91_PMC_SR]
tst tmp1, #AT91_PMC_MOSCS
beq 1b
-2:
.endm
/*
* Wait until PLLA has locked.
*/
.macro wait_pllalock
- mov tmp2, #PLLALOCK_TIMEOUT
-1: sub tmp2, tmp2, #1
- cmp tmp2, #0
- beq 2f
- ldr tmp1, [pmc, #AT91_PMC_SR]
+1: ldr tmp1, [pmc, #AT91_PMC_SR]
tst tmp1, #AT91_PMC_LOCKA
beq 1b
-2:
.endm
/*
* Wait until PLLB has locked.
*/
.macro wait_pllblock
- mov tmp2, #PLLBLOCK_TIMEOUT
-1: sub tmp2, tmp2, #1
- cmp tmp2, #0
- beq 2f
- ldr tmp1, [pmc, #AT91_PMC_SR]
+1: ldr tmp1, [pmc, #AT91_PMC_SR]
tst tmp1, #AT91_PMC_LOCKB
beq 1b
-2:
.endm
.text
+ .arm
+
/* void at91_slow_clock(void __iomem *pmc, void __iomem *sdramc,
* void __iomem *ramc1, int memctrl)
*/
cmp memctrl, #AT91_MEMCTRL_DDRSDR
bne sdr_sr_enable
+ /* LPDDR1 --> force DDR2 mode during self-refresh */
+ ldr tmp1, [sdramc, #AT91_DDRSDRC_MDR]
+ str tmp1, .saved_sam9_mdr
+ bic tmp1, tmp1, #~AT91_DDRSDRC_MD
+ cmp tmp1, #AT91_DDRSDRC_MD_LOW_POWER_DDR
+ ldreq tmp1, [sdramc, #AT91_DDRSDRC_MDR]
+ biceq tmp1, tmp1, #AT91_DDRSDRC_MD
+ orreq tmp1, tmp1, #AT91_DDRSDRC_MD_DDR2
+ streq tmp1, [sdramc, #AT91_DDRSDRC_MDR]
+
/* prepare for DDRAM self-refresh mode */
ldr tmp1, [sdramc, #AT91_DDRSDRC_LPR]
str tmp1, .saved_sam9_lpr
/* figure out if we use the second ram controller */
cmp ramc1, #0
- ldrne tmp2, [ramc1, #AT91_DDRSDRC_LPR]
- strne tmp2, .saved_sam9_lpr1
- bicne tmp2, #AT91_DDRSDRC_LPCB
- orrne tmp2, #AT91_DDRSDRC_LPCB_SELF_REFRESH
+ beq ddr_no_2nd_ctrl
+
+ ldr tmp2, [ramc1, #AT91_DDRSDRC_MDR]
+ str tmp2, .saved_sam9_mdr1
+ bic tmp2, tmp2, #~AT91_DDRSDRC_MD
+ cmp tmp2, #AT91_DDRSDRC_MD_LOW_POWER_DDR
+ ldreq tmp2, [ramc1, #AT91_DDRSDRC_MDR]
+ biceq tmp2, tmp2, #AT91_DDRSDRC_MD
+ orreq tmp2, tmp2, #AT91_DDRSDRC_MD_DDR2
+ streq tmp2, [ramc1, #AT91_DDRSDRC_MDR]
+
+ ldr tmp2, [ramc1, #AT91_DDRSDRC_LPR]
+ str tmp2, .saved_sam9_lpr1
+ bic tmp2, #AT91_DDRSDRC_LPCB
+ orr tmp2, #AT91_DDRSDRC_LPCB_SELF_REFRESH
/* Enable DDRAM self-refresh mode */
+ str tmp2, [ramc1, #AT91_DDRSDRC_LPR]
+ddr_no_2nd_ctrl:
str tmp1, [sdramc, #AT91_DDRSDRC_LPR]
- strne tmp2, [ramc1, #AT91_DDRSDRC_LPR]
b sdr_sr_done
/* Turn off the main oscillator */
ldr tmp1, [pmc, #AT91_CKGR_MOR]
bic tmp1, tmp1, #AT91_PMC_MOSCEN
+ orr tmp1, tmp1, #AT91_PMC_KEY
str tmp1, [pmc, #AT91_CKGR_MOR]
/* Wait for interrupt */
/* Turn on the main oscillator */
ldr tmp1, [pmc, #AT91_CKGR_MOR]
orr tmp1, tmp1, #AT91_PMC_MOSCEN
+ orr tmp1, tmp1, #AT91_PMC_KEY
str tmp1, [pmc, #AT91_CKGR_MOR]
wait_moscrdy
*/
cmp memctrl, #AT91_MEMCTRL_DDRSDR
bne sdr_en_restore
+ /* Restore MDR in case of LPDDR1 */
+ ldr tmp1, .saved_sam9_mdr
+ str tmp1, [sdramc, #AT91_DDRSDRC_MDR]
/* Restore LPR on AT91 with DDRAM */
ldr tmp1, .saved_sam9_lpr
str tmp1, [sdramc, #AT91_DDRSDRC_LPR]
/* if we use the second ram controller */
cmp ramc1, #0
+ ldrne tmp2, .saved_sam9_mdr1
+ strne tmp2, [ramc1, #AT91_DDRSDRC_MDR]
ldrne tmp2, .saved_sam9_lpr1
strne tmp2, [ramc1, #AT91_DDRSDRC_LPR]
.saved_sam9_lpr1:
.word 0
+.saved_sam9_mdr:
+ .word 0
+
+.saved_sam9_mdr1:
+ .word 0
+
ENTRY(at91_slow_clock_sz)
.word .-at91_slow_clock
*/
void exynos_cpu_power_down(int cpu)
{
- if (cpu == 0 && (of_machine_is_compatible("samsung,exynos5420") ||
- of_machine_is_compatible("samsung,exynos5800"))) {
+ if (cpu == 0 && (soc_is_exynos5420() || soc_is_exynos5800())) {
/*
* Bypass power down for CPU0 during suspend. Check for
* the SYS_PWR_REG value to decide if we are suspending
of_genpd_add_provider_simple(np, &pd->pd);
}
+ /* Assign the child power domains to their parents */
+ for_each_compatible_node(np, NULL, "samsung,exynos4210-pd") {
+ struct generic_pm_domain *child_domain, *parent_domain;
+ struct of_phandle_args args;
+
+ args.np = np;
+ args.args_count = 0;
+ child_domain = of_genpd_get_from_provider(&args);
+ if (!child_domain)
+ continue;
+
+ if (of_parse_phandle_with_args(np, "power-domains",
+ "#power-domain-cells", 0, &args) != 0)
+ continue;
+
+ parent_domain = of_genpd_get_from_provider(&args);
+ if (!parent_domain)
+ continue;
+
+ if (pm_genpd_add_subdomain(parent_domain, child_domain))
+ pr_warn("%s failed to add subdomain: %s\n",
+ parent_domain->name, child_domain->name);
+ else
+ pr_info("%s has as child subdomain: %s.\n",
+ parent_domain->name, child_domain->name);
+ of_node_put(np);
+ }
+
return 0;
}
arch_initcall(exynos4_pm_init_power_domain);
static u32 exynos_irqwake_intmask = 0xffffffff;
static const struct exynos_wkup_irq exynos3250_wkup_irq[] = {
- { 73, BIT(1) }, /* RTC alarm */
- { 74, BIT(2) }, /* RTC tick */
+ { 105, BIT(1) }, /* RTC alarm */
+ { 106, BIT(2) }, /* RTC tick */
{ /* sentinel */ },
};
if (ret == -EBUSY)
pr_warn("omap_hwmod: %s: failed to hardreset\n", oh->name);
- if (!ret) {
+ if (oh->clkdm) {
/*
* Set the clockdomain to HW_AUTO, assuming that the
* previous state was HW_AUTO.
*/
- if (oh->clkdm && hwsup)
+ if (hwsup)
clkdm_allow_idle(oh->clkdm);
- } else {
- if (oh->clkdm)
- clkdm_hwmod_disable(oh->clkdm, oh);
+
+ clkdm_hwmod_disable(oh->clkdm, oh);
}
return ret;
INIT_LIST_HEAD(&oh->master_ports);
INIT_LIST_HEAD(&oh->slave_ports);
spin_lock_init(&oh->_lock);
+ lockdep_set_class(&oh->_lock, &oh->hwmod_key);
oh->_state = _HWMOD_STATE_REGISTERED;
u32 _sysc_cache;
void __iomem *_mpu_rt_va;
spinlock_t _lock;
+ struct lock_class_key hwmod_key; /* unique lock class */
struct list_head node;
struct omap_hwmod_ocp_if *_mpu_port;
unsigned int (*xlate_irq)(unsigned int);
*
*/
-static struct omap_hwmod_class dra7xx_pcie_hwmod_class = {
+static struct omap_hwmod_class dra7xx_pciess_hwmod_class = {
.name = "pcie",
};
/* pcie1 */
-static struct omap_hwmod dra7xx_pcie1_hwmod = {
+static struct omap_hwmod dra7xx_pciess1_hwmod = {
.name = "pcie1",
- .class = &dra7xx_pcie_hwmod_class,
+ .class = &dra7xx_pciess_hwmod_class,
.clkdm_name = "pcie_clkdm",
.main_clk = "l4_root_clk_div",
- .prcm = {
- .omap4 = {
- .clkctrl_offs = DRA7XX_CM_PCIE_CLKSTCTRL_OFFSET,
- .modulemode = MODULEMODE_SWCTRL,
- },
- },
-};
-
-/* pcie2 */
-static struct omap_hwmod dra7xx_pcie2_hwmod = {
- .name = "pcie2",
- .class = &dra7xx_pcie_hwmod_class,
- .clkdm_name = "pcie_clkdm",
- .main_clk = "l4_root_clk_div",
- .prcm = {
- .omap4 = {
- .clkctrl_offs = DRA7XX_CM_PCIE_CLKSTCTRL_OFFSET,
- .modulemode = MODULEMODE_SWCTRL,
- },
- },
-};
-
-/*
- * 'PCIE PHY' class
- *
- */
-
-static struct omap_hwmod_class dra7xx_pcie_phy_hwmod_class = {
- .name = "pcie-phy",
-};
-
-/* pcie1 phy */
-static struct omap_hwmod dra7xx_pcie1_phy_hwmod = {
- .name = "pcie1-phy",
- .class = &dra7xx_pcie_phy_hwmod_class,
- .clkdm_name = "l3init_clkdm",
- .main_clk = "l4_root_clk_div",
.prcm = {
.omap4 = {
.clkctrl_offs = DRA7XX_CM_L3INIT_PCIESS1_CLKCTRL_OFFSET,
},
};
-/* pcie2 phy */
-static struct omap_hwmod dra7xx_pcie2_phy_hwmod = {
- .name = "pcie2-phy",
- .class = &dra7xx_pcie_phy_hwmod_class,
- .clkdm_name = "l3init_clkdm",
+/* pcie2 */
+static struct omap_hwmod dra7xx_pciess2_hwmod = {
+ .name = "pcie2",
+ .class = &dra7xx_pciess_hwmod_class,
+ .clkdm_name = "pcie_clkdm",
.main_clk = "l4_root_clk_div",
.prcm = {
.omap4 = {
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-/* l3_main_1 -> pcie1 */
-static struct omap_hwmod_ocp_if dra7xx_l3_main_1__pcie1 = {
+/* l3_main_1 -> pciess1 */
+static struct omap_hwmod_ocp_if dra7xx_l3_main_1__pciess1 = {
.master = &dra7xx_l3_main_1_hwmod,
- .slave = &dra7xx_pcie1_hwmod,
+ .slave = &dra7xx_pciess1_hwmod,
.clk = "l3_iclk_div",
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-/* l4_cfg -> pcie1 */
-static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pcie1 = {
+/* l4_cfg -> pciess1 */
+static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pciess1 = {
.master = &dra7xx_l4_cfg_hwmod,
- .slave = &dra7xx_pcie1_hwmod,
+ .slave = &dra7xx_pciess1_hwmod,
.clk = "l4_root_clk_div",
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-/* l3_main_1 -> pcie2 */
-static struct omap_hwmod_ocp_if dra7xx_l3_main_1__pcie2 = {
+/* l3_main_1 -> pciess2 */
+static struct omap_hwmod_ocp_if dra7xx_l3_main_1__pciess2 = {
.master = &dra7xx_l3_main_1_hwmod,
- .slave = &dra7xx_pcie2_hwmod,
+ .slave = &dra7xx_pciess2_hwmod,
.clk = "l3_iclk_div",
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-/* l4_cfg -> pcie2 */
-static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pcie2 = {
- .master = &dra7xx_l4_cfg_hwmod,
- .slave = &dra7xx_pcie2_hwmod,
- .clk = "l4_root_clk_div",
- .user = OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* l4_cfg -> pcie1 phy */
-static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pcie1_phy = {
- .master = &dra7xx_l4_cfg_hwmod,
- .slave = &dra7xx_pcie1_phy_hwmod,
- .clk = "l4_root_clk_div",
- .user = OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* l4_cfg -> pcie2 phy */
-static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pcie2_phy = {
+/* l4_cfg -> pciess2 */
+static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pciess2 = {
.master = &dra7xx_l4_cfg_hwmod,
- .slave = &dra7xx_pcie2_phy_hwmod,
+ .slave = &dra7xx_pciess2_hwmod,
.clk = "l4_root_clk_div",
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
&dra7xx_l4_cfg__mpu,
&dra7xx_l4_cfg__ocp2scp1,
&dra7xx_l4_cfg__ocp2scp3,
- &dra7xx_l3_main_1__pcie1,
- &dra7xx_l4_cfg__pcie1,
- &dra7xx_l3_main_1__pcie2,
- &dra7xx_l4_cfg__pcie2,
- &dra7xx_l4_cfg__pcie1_phy,
- &dra7xx_l4_cfg__pcie2_phy,
+ &dra7xx_l3_main_1__pciess1,
+ &dra7xx_l4_cfg__pciess1,
+ &dra7xx_l3_main_1__pciess2,
+ &dra7xx_l4_cfg__pciess2,
&dra7xx_l3_main_1__qspi,
&dra7xx_l4_per3__rtcss,
&dra7xx_l4_cfg__sata,
static void __init omap3_evm_legacy_init(void)
{
+ hsmmc2_internal_input_clk();
legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 149);
}
{
saved_mask[0] =
omap4_prm_read_inst_reg(OMAP4430_PRM_OCP_SOCKET_INST,
- OMAP4_PRM_IRQSTATUS_MPU_OFFSET);
+ OMAP4_PRM_IRQENABLE_MPU_OFFSET);
saved_mask[1] =
omap4_prm_read_inst_reg(OMAP4430_PRM_OCP_SOCKET_INST,
- OMAP4_PRM_IRQSTATUS_MPU_2_OFFSET);
+ OMAP4_PRM_IRQENABLE_MPU_2_OFFSET);
omap4_prm_write_inst_reg(0, OMAP4430_PRM_OCP_SOCKET_INST,
OMAP4_PRM_IRQENABLE_MPU_OFFSET);
extern unsigned long socfpga_cpu1start_addr;
-#define SOCFPGA_SCU_VIRT_BASE 0xfffec000
+#define SOCFPGA_SCU_VIRT_BASE 0xfee00000
#endif
#include <asm/hardware/cache-l2x0.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
+#include <asm/cacheflush.h>
#include "core.h"
(u32 *) &socfpga_cpu1start_addr))
pr_err("SMP: Need cpu1-start-addr in device tree.\n");
+ /* Ensure that socfpga_cpu1start_addr is visible to other CPUs */
+ smp_wmb();
+ sync_cache_w(&socfpga_cpu1start_addr);
+
sys_manager_base_addr = of_iomap(np, 0);
np = of_find_compatible_node(NULL, NULL, "altr,rst-mgr");
"st,stih415",
"st,stih416",
"st,stih407",
+ "st,stih410",
"st,stih418",
NULL
};
#define PULL_DISABLE (1 << 3)
#define INPUT_EN (1 << 5)
-#define SLEWCTRL_FAST (1 << 6)
+#define SLEWCTRL_SLOW (1 << 6)
+#define SLEWCTRL_FAST 0
/* update macro depending on INPUT_EN and PULL_ENA */
#undef PIN_OUTPUT
#define PULL_DISABLE (1 << 16)
#define PULL_UP (1 << 17)
#define INPUT_EN (1 << 18)
-#define SLEWCTRL_FAST (1 << 19)
+#define SLEWCTRL_SLOW (1 << 19)
+#define SLEWCTRL_FAST 0
#define DS0_PULL_UP_DOWN_EN (1 << 27)
#define PIN_OUTPUT (PULL_DISABLE)
#define AT91_DDRSDRC_UPD_MR (3 << 20) /* Update load mode register and extended mode register */
#define AT91_DDRSDRC_MDR 0x20 /* Memory Device Register */
-#define AT91_DDRSDRC_MD (3 << 0) /* Memory Device Type */
+#define AT91_DDRSDRC_MD (7 << 0) /* Memory Device Type */
#define AT91_DDRSDRC_MD_SDR 0
#define AT91_DDRSDRC_MD_LOW_POWER_SDR 1
#define AT91_DDRSDRC_MD_LOW_POWER_DDR 3
projects / firefly-linux-kernel-4.4.55.git / commitdiff