UPSTREAM: ARM: dts: rockchip: add the sdio power sequence for kylin board

This patch adds the sdio power sequence for kylin board.
The WLAN attached to a SDIO interface, wifi/bluetooth have
reset and power been needed to enable.

AFAIK, the simple power sequence provider sets a value for multiple GPIOs.
So the reset and power of WlAN chip can be handled in mmc power sequence.
On the module itself this is one of these, that should can be handled
by reset GPIOs in simple mmc power sequence.

The Bluetooth host wake is high active from bootup, this patch is also
set pinctrl bias as the default to enable the pull up in soc internal.

Change-Id: I422b0d2de86460c05239f1864322986abec59073
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
(cherry picked from git.kernel.org next/linux-next.git master
 commit 4a9d0b033702566cde2f33ed19ff9c8a90b7fe8f)

diff --git a/arch/arm/boot/dts/rk3036-kylin.dts b/arch/arm/boot/dts/rk3036-kylin.dts
index 905e187da381fe1898a705e60298c6ab878fc969..6a32b234525a3f90036fc5b99414c52b6b486f86 100644 (file)
--- a/arch/arm/boot/dts/rk3036-kylin.dts
+++ b/arch/arm/boot/dts/rk3036-kylin.dts
@@ -46,6 +46,23 @@
        model = "Rockchip RK3036 KylinBoard";
        compatible = "rockchip,rk3036-kylin", "rockchip,rk3036";
 
+       sdio_pwrseq: sdio-pwrseq {
+               compatible = "mmc-pwrseq-simple";
+               pinctrl-names = "default";
+               pinctrl-0 = <&bt_wake_h>;
+
+               /*
+                * On the module itself this is one of these (depending
+                * on the actual card populated):
+                * - SDIO_RESET_L_WL_REG_ON
+                * - SDIO_RESET_L_WL_RST
+                * - SDIO_RESET_L_BT_EN
+                */
+               reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>, /* WL_REG_ON */
+                             <&gpio0 27 GPIO_ACTIVE_LOW>, /* WL_RST */
+                             <&gpio2 9  GPIO_ACTIVE_LOW>; /* BT_EN */
+       };
+
        sound {
                compatible = "simple-audio-card";
                simple-audio-card,format = "i2s";
@@ -303,6 +320,7 @@
        cap-sdio-irq;
        default-sample-phase = <90>;
        keep-power-in-suspend;
+       mmc-pwrseq = <&sdio_pwrseq>;
        non-removable;
        num-slots = <1>;
        pinctrl-names = "default";
@@ -336,6 +354,12 @@
                };
        };
 
+       sdio {
+               bt_wake_h: bt-wake-h {
+                       rockchip,pins = <2 8 RK_FUNC_GPIO &pcfg_pull_default>;
+               };
+       };
+
        sleep {
                global_pwroff: global-pwroff {
                        rockchip,pins = <2 7 RK_FUNC_1 &pcfg_pull_none>;