ARM: mach-shmobile: Use shared GIC entry macros

Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the R-Mobile / SH-Mobile processors.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

diff --git a/arch/arm/mach-shmobile/include/mach/entry-macro-gic.S b/arch/arm/mach-shmobile/include/mach/entry-macro-gic.S
index 50b1f16d54a2d44a370c34b9dbbc1a040edbca72..48872dd152698f0ea2e1ed126bc05e49d19c10ca 100644 (file)
--- a/arch/arm/mach-shmobile/include/mach/entry-macro-gic.S
+++ b/arch/arm/mach-shmobile/include/mach/entry-macro-gic.S
@@ -16,6 +16,7 @@
  */
 #include <mach/hardware.h>
 #include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
 
        .macro  disable_fiq
        .endm
@@ -26,64 +27,3 @@
 
        .macro  arch_ret_to_user, tmp1, tmp2
        .endm
-
-       /*
-        * The interrupt numbering scheme is defined in the
-        * interrupt controller spec.  To wit:
-        *
-        * Interrupts 0-15 are IPI
-        * 16-28 are reserved
-        * 29-31 are local.  We allow 30 to be used for the watchdog.
-        * 32-1020 are global
-        * 1021-1022 are reserved
-        * 1023 is "spurious" (no interrupt)
-        *
-        * For now, we ignore all local interrupts so only return an
-        * interrupt if it's between 30 and 1020.  The test_for_ipi
-        * routine below will pick up on IPIs.
-        *
-        * A simple read from the controller will tell us the number of
-        * the highest priority enabled interrupt.  We then just need to
-        * check whether it is in the valid range for an IRQ (30-1020
-        * inclusive).
-        */
-
-       .macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-       ldr     \irqstat, [\base, #GIC_CPU_INTACK]
-       /* bits 12-10 = src CPU, 9-0 = int # */
-
-       ldr     \tmp, =1021
-       bic     \irqnr, \irqstat, #0x1c00
-       cmp     \irqnr, #29
-       cmpcc   \irqnr, \irqnr
-       cmpne   \irqnr, \tmp
-       cmpcs   \irqnr, \irqnr
-
-       .endm
-
-       /*
-        * We assume that irqstat (the raw value of the IRQ acknowledge
-        * register) is preserved from the macro above.
-        * If there is an IPI, we immediately signal end of interrupt on the
-        * controller, since this requires the original irqstat value which
-        * we won't easily be able to recreate later.
-        */
-
-       .macro test_for_ipi, irqnr, irqstat, base, tmp
-       bic     \irqnr, \irqstat, #0x1c00
-       cmp     \irqnr, #16
-       strcc   \irqstat, [\base, #GIC_CPU_EOI]
-       cmpcs   \irqnr, \irqnr
-       .endm
-
-       /* As above, this assumes that irqstat and base are preserved.. */
-
-       .macro test_for_ltirq, irqnr, irqstat, base, tmp
-       bic     \irqnr, \irqstat, #0x1c00
-       mov     \tmp, #0
-       cmp     \irqnr, #29
-       moveq   \tmp, #1
-       streq   \irqstat, [\base, #GIC_CPU_EOI]
-       cmp     \tmp, #0
-       .endm