X-Git-Url: http://plrg.eecs.uci.edu/git/?a=blobdiff_plain;f=drivers%2Fthermal%2Fimx_thermal.c;h=c5547bd711dbe2b4d681e54213e25e992afb51af;hb=25e1c1c2865f7b91b8d60a16734100f3cb67722d;hp=c8fe3cac2e0e04d8196694f264b6d9f4fcd5cc5d;hpb=934f98d7e8123892bd9ca8ea08728ee0784e6597;p=firefly-linux-kernel-4.4.55.git

diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
index c8fe3cac2e0e..c5547bd711db 100644
--- a/drivers/thermal/imx_thermal.c
+++ b/drivers/thermal/imx_thermal.c
@@ -55,6 +55,7 @@
 #define TEMPSENSE2_PANIC_VALUE_SHIFT	16
 #define TEMPSENSE2_PANIC_VALUE_MASK	0xfff0000
 
+#define OCOTP_MEM0			0x0480
 #define OCOTP_ANA1			0x04e0
 
 /* The driver supports 1 passive trip point and 1 critical trip point */
@@ -64,12 +65,6 @@ enum imx_thermal_trip {
 	IMX_TRIP_NUM,
 };
 
-/*
- * It defines the temperature in millicelsius for passive trip point
- * that will trigger cooling action when crossed.
- */
-#define IMX_TEMP_PASSIVE		85000
-
 #define IMX_POLLING_DELAY		2000 /* millisecond */
 #define IMX_PASSIVE_DELAY		1000
 
@@ -100,12 +95,14 @@ struct imx_thermal_data {
 	u32 c1, c2; /* See formula in imx_get_sensor_data() */
 	int temp_passive;
 	int temp_critical;
+	int temp_max;
 	int alarm_temp;
 	int last_temp;
 	bool irq_enabled;
 	int irq;
 	struct clk *thermal_clk;
 	const struct thermal_soc_data *socdata;
+	const char *temp_grade;
 };
 
 static void imx_set_panic_temp(struct imx_thermal_data *data,
@@ -285,10 +282,12 @@ static int imx_set_trip_temp(struct thermal_zone_device *tz, int trip,
 {
 	struct imx_thermal_data *data = tz->devdata;
 
+	/* do not allow changing critical threshold */
 	if (trip == IMX_TRIP_CRITICAL)
 		return -EPERM;
 
-	if (temp < 0 || temp > IMX_TEMP_PASSIVE)
+	/* do not allow passive to be set higher than critical */
+	if (temp < 0 || temp > data->temp_critical)
 		return -EINVAL;
 
 	data->temp_passive = temp;
@@ -404,17 +403,39 @@ static int imx_get_sensor_data(struct platform_device *pdev)
 	data->c1 = temp64;
 	data->c2 = n1 * data->c1 + 1000 * t1;
 
-	/*
-	 * Set the default passive cooling trip point,
-	 * can be changed from userspace.
-	 */
-	data->temp_passive = IMX_TEMP_PASSIVE;
+	/* use OTP for thermal grade */
+	ret = regmap_read(map, OCOTP_MEM0, &val);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to read temp grade: %d\n", ret);
+		return ret;
+	}
+
+	/* The maximum die temp is specified by the Temperature Grade */
+	switch ((val >> 6) & 0x3) {
+	case 0: /* Commercial (0 to 95C) */
+		data->temp_grade = "Commercial";
+		data->temp_max = 95000;
+		break;
+	case 1: /* Extended Commercial (-20 to 105C) */
+		data->temp_grade = "Extended Commercial";
+		data->temp_max = 105000;
+		break;
+	case 2: /* Industrial (-40 to 105C) */
+		data->temp_grade = "Industrial";
+		data->temp_max = 105000;
+		break;
+	case 3: /* Automotive (-40 to 125C) */
+		data->temp_grade = "Automotive";
+		data->temp_max = 125000;
+		break;
+	}
 
 	/*
-	 * The maximum die temperature set to 20 C higher than
-	 * IMX_TEMP_PASSIVE.
+	 * Set the critical trip point at 5C under max
+	 * Set the passive trip point at 10C under max (can change via sysfs)
 	 */
-	data->temp_critical = 1000 * 20 + data->temp_passive;
+	data->temp_critical = data->temp_max - (1000 * 5);
+	data->temp_passive = data->temp_max - (1000 * 10);
 
 	return 0;
 }
@@ -551,6 +572,11 @@ static int imx_thermal_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	dev_info(&pdev->dev, "%s CPU temperature grade - max:%dC"
+		 " critical:%dC passive:%dC\n", data->temp_grade,
+		 data->temp_max / 1000, data->temp_critical / 1000,
+		 data->temp_passive / 1000);
+
 	/* Enable measurements at ~ 10 Hz */
 	regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
 	measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */