--- /dev/null
+#ifndef REALTEK_POWER_SEQUENCE_8188F
+#define REALTEK_POWER_SEQUENCE_8188F
+
+#include "HalPwrSeqCmd.h"
+
+/*
+ Check document WM-20130815-JackieLau-RTL8188F_Power_Architecture v08.vsd
+ There are 6 HW Power States:
+ 0: POFF--Power Off
+ 1: PDN--Power Down
+ 2: CARDEMU--Card Emulation
+ 3: ACT--Active Mode
+ 4: LPS--Low Power State
+ 5: SUS--Suspend
+
+ The transision from different states are defined below
+ TRANS_CARDEMU_TO_ACT
+ TRANS_ACT_TO_CARDEMU
+ TRANS_CARDEMU_TO_SUS
+ TRANS_SUS_TO_CARDEMU
+ TRANS_CARDEMU_TO_PDN
+ TRANS_ACT_TO_LPS
+ TRANS_LPS_TO_ACT
+
+ TRANS_END
+*/
+#define RTL8188F_TRANS_CARDEMU_TO_ACT_STEPS 13
+#define RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS 15
+#define RTL8188F_TRANS_CARDEMU_TO_SUS_STEPS 14
+#define RTL8188F_TRANS_SUS_TO_CARDEMU_STEPS 15
+#define RTL8188F_TRANS_CARDEMU_TO_PDN_STEPS 15
+#define RTL8188F_TRANS_PDN_TO_CARDEMU_STEPS 15
+#define RTL8188F_TRANS_ACT_TO_LPS_STEPS 11
+#define RTL8188F_TRANS_LPS_TO_ACT_STEPS 13
+#define RTL8188F_TRANS_ACT_TO_SWLPS_STEPS 21
+#define RTL8188F_TRANS_SWLPS_TO_ACT_STEPS 14
+#define RTL8188F_TRANS_END_STEPS 1
+
+
+#define RTL8188F_TRANS_CARDEMU_TO_ACT \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0},/* disable SW LPS 0x04[10]=0*/ \
+ {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1 power ready*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]=0*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT3), 0},/* 0x4[11]=1'b0 disable WL suspend*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* 0x4[8]=1 polling until return 0*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0},/**/ \
+ {0x0027, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x35}, /*0x27<=35 to reduce RF noise*/
+
+#define RTL8188F_TRANS_ACT_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \
+ {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/*0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */\
+ {0x0027, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x34}, /*0x27 <= 34, xtal_qsel = 0 to xtal bring up*/\
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
+
+#define RTL8188F_TRANS_CARDEMU_TO_SUS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00}, /*0x07 = 0x00 , SOP option to disable BG/MB*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ \
+ {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4},/* 0xC4[4] <= 1, turn off USB APHY LDO under suspend mode*/
+
+#define RTL8188F_TRANS_SUS_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/ \
+ {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0},/* 0xC4[4] <= 1, turn off USB APHY LDO under suspend mode*/
+
+#define RTL8188F_TRANS_CARDEMU_TO_CARDDIS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00}, /*0x07 = 0x00 , SOP option to disable BG/MB*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ \
+ {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4},/* 0xC4[4] <= 1, turn off USB APHY LDO under suspend mode*/
+
+#define RTL8188F_TRANS_CARDDIS_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/ \
+ {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0},/* 0xC4[4] <= 1, turn off USB APHY LDO under suspend mode*/
+
+
+#define RTL8188F_TRANS_CARDEMU_TO_PDN \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/
+
+#define RTL8188F_TRANS_PDN_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/
+
+#define RTL8188F_TRANS_ACT_TO_LPS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0139, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*set RPWM IMR*/ \
+ {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \
+ {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/ \
+ {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \
+ {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \
+ {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/
+
+
+#define RTL8188F_TRANS_LPS_TO_ACT \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
+ {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
+ {0x0027, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x35},/*xtal_qsel = 1 for low noise*/ \
+ {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0 TSF in 40M*/\
+ {0x002B, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x1c, 0x1c}, /*. 0x2b[4:2] = 3b'111 to enable BB, AFE clock*/\
+ {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1*/\
+ {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1 | BIT0, BIT1 | BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\
+ {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/
+
+
+#define RTL8188F_TRANS_ACT_TO_SWLPS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0139, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*set RPWM IMR*/ \
+ {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \
+ {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/ \
+ {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \
+ {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \
+ {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/ \
+ {0x002b, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x1C, 0x00},/*0x2b[4:2]<=0 to gated BB, AFE clock*/ \
+ {0x0027, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x34},/*xtal_qsel = 0 for bring up*/ \
+ {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x00},/* sdio LPS option*/ \
+ {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x83},/* usb LPS option, open bandgap, xtal*/ \
+ {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, 0}, /* 0xC4[5]<=0, digital LDO no standby mode*/ \
+ {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7}, /* 0xC4[7]<=1, on domain voltage adjust*/ \
+ {0x00a7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0xe0}, /* low power LPS enable for sdio*/ \
+ {0x00a7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0xe4}, /* low power LPS enable for usb*/ \
+ {0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /* enable WL_LPS_EN*/
+
+
+#define RTL8188F_TRANS_SWLPS_TO_ACT \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/*polling TSF stable*/\
+ {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1, enable security engine*/\
+ {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\
+ {0x06B7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x09}, /*. reset MAC rx state machine*/\
+ {0x06B4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x86}, /*. reset MAC rx state machine*/\
+ {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/* set CPU RAM code ready*/ \
+ {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/ \
+ {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0},/* Enable CPU*/ \
+ {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*enable CPU IO Wrapper*/ \
+ {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2},/* Enable CPU*/ \
+ {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, BIT7},/*polling FW init ready */ \
+ {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT6, BIT6},/*polling FW init ready */ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\
+ {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/
+
+#define RTL8188F_TRANS_END \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0},
+
+
+ extern WLAN_PWR_CFG rtl8188F_power_on_flow[RTL8188F_TRANS_CARDEMU_TO_ACT_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_radio_off_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_card_disable_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_card_enable_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_suspend_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_SUS_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_resume_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_SUS_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_hwpdn_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_enter_lps_flow[RTL8188F_TRANS_ACT_TO_LPS_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_leave_lps_flow[RTL8188F_TRANS_LPS_TO_ACT_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_enter_swlps_flow[RTL8188F_TRANS_ACT_TO_SWLPS_STEPS + RTL8188F_TRANS_END_STEPS];
+ extern WLAN_PWR_CFG rtl8188F_leave_swlps_flow[RTL8188F_TRANS_SWLPS_TO_ACT_STEPS + RTL8188F_TRANS_END_STEPS];
+#endif
projects / firefly-linux-kernel-4.4.55.git / blobdiff