--- /dev/null
+#include "mp_precomp.h"
+
+
+VOID
+ex_hal8723b_wifi_only_hw_config(
+ IN struct wifi_only_cfg *pwifionlycfg
+ )
+{
+ struct wifi_only_haldata *pwifionly_haldata = &pwifionlycfg->haldata_info;
+
+
+ halwifionly_write1byte(pwifionlycfg, 0x778, 0x3); /* Set pta for wifi first priority, 0x1 need to reference pta table to determine wifi and bt priority */
+ halwifionly_bitmaskwrite1byte(pwifionlycfg, 0x40, 0x20, 0x1);
+
+ /* Set Antenna path to Wifi */
+ halwifionly_write2byte(pwifionlycfg, 0x0765, 0x8); /* Set pta for wifi first priority, 0x0 need to reference pta table to determine wifi and bt priority */
+ halwifionly_write2byte(pwifionlycfg, 0x076e, 0xc);
+
+ halwifionly_write4byte(pwifionlycfg, 0x000006c0, 0xaaaaaaaa); /* pta table, 0xaaaaaaaa means wifi is higher priority than bt */
+ halwifionly_write4byte(pwifionlycfg, 0x000006c4, 0xaaaaaaaa);
+
+ halwifionly_bitmaskwrite1byte(pwifionlycfg, 0x67, 0x20, 0x1); /* BT select s0/s1 is controlled by WiFi */
+
+ /* 0x948 setting */
+ if (pwifionlycfg->chip_interface == WIFIONLY_INTF_PCI) {
+ /* HP Foxconn NGFF at S0
+ not sure HP pg correct or not(EEPROMBluetoothSingleAntPath), so here we just write
+ 0x948=0x280 for HP HW id NIC. */
+ if (pwifionly_haldata->customer_id == CUSTOMER_HP_1) {
+ halwifionly_write4byte(pwifionlycfg, 0x948, 0x280);
+ halwifionly_phy_set_rf_reg(pwifionlycfg, 0, 0x1, 0xfffff, 0x0); /* WiFi TRx Mask off */
+ return;
+ }
+ }
+
+ if (pwifionly_haldata->efuse_pg_antnum == 2) {
+ halwifionly_write4byte(pwifionlycfg, 0x948, 0x0);
+ } else {
+ /* 3Attention !!! For 8723BU !!!!
+ For 8723BU single ant case: jira [USB-1237]
+ Because of 8723BU S1 has HW problem, we only can use S0 instead.
+ Whether Efuse 0xc3 [6] is 0 or 1, we should always use S0 and write 0x948 to 80/280
+
+ --------------------------------------------------
+ BT Team :
+ When in Single Ant case, Reg[0x948] has two case : 0x80 or 0x200
+ When in Two Ant case, Reg[0x948] has two case : 0x280 or 0x0
+ Efuse 0xc3 [6] Antenna Path
+ 0xc3 [6] = 0 ==> S1 ==> 0x948 = 0/40/200
+ 0xc3 [6] = 1 ==> S0 ==> 0x948 = 80/240/280 */
+
+ if (pwifionlycfg->chip_interface == WIFIONLY_INTF_USB)
+ halwifionly_write4byte(pwifionlycfg, 0x948, 0x80);
+ else {
+ if (pwifionly_haldata->efuse_pg_antpath == 0)
+ halwifionly_write4byte(pwifionlycfg, 0x948, 0x0);
+ else
+ halwifionly_write4byte(pwifionlycfg, 0x948, 0x280);
+ }
+
+ }
+
+
+ /* after 8723B F-cut, TRx Mask should be set when 0x948=0x0 or 0x280
+ PHY_SetRFReg(Adapter, 0, 0x1, 0xfffff, 0x780); WiFi TRx Mask on */
+ halwifionly_phy_set_rf_reg(pwifionlycfg, 0, 0x1, 0xfffff, 0x0); /*WiFi TRx Mask off */
+
+}