#include <linux/debugfs.h>
#include <linux/device.h>
#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/mmc/host.h>
#include <linux/mmc/mmc.h>
#include <linux/mmc/sd.h>
+#include <linux/mmc/card.h>
#include <linux/mmc/sdio.h>
#include <linux/mmc/rk_mmc.h>
#include <linux/bitops.h>
#include <linux/of.h>
#include <linux/of_gpio.h>
#include <linux/mmc/slot-gpio.h>
+#include <linux/clk-private.h>
+#include <linux/rockchip/cpu.h>
#include "rk_sdmmc.h"
-#include "rk_sdmmc_of.h"
+#include "rk_sdmmc_dbg.h"
#include <linux/regulator/rockchip_io_vol_domain.h>
+#include "../../clk/rockchip/clk-ops.h"
-#define RK_SDMMC_DRIVER_VERSION "Ver 1.00. The last modify date is 2014-05-05"
+#define RK_SDMMC_DRIVER_VERSION "Ver 1.13 2014-09-05"
/* Common flag combinations */
#define DW_MCI_DATA_ERROR_FLAGS (SDMMC_INT_DRTO | SDMMC_INT_DCRC | \
#define DW_MCI_FREQ_MAX 50000000//200000000 /* unit: HZ */
#define DW_MCI_FREQ_MIN 300000//400000 /* unit: HZ */
-#define SDMMC_DATA_TIMEOUT_SD 500; /*max is 250ms showed in Spec; Maybe adapt the value for the sick card.*/
+/*max is 250ms showed in Spec; Maybe adapt the value for the sick card.*/
+#define SDMMC_DATA_TIMEOUT_SD 500
#define SDMMC_DATA_TIMEOUT_SDIO 250
#define SDMMC_DATA_TIMEOUT_EMMC 2500
-#define SDMMC_CMD_RTO_MAX_HOLD 200
+#define SDMMC_CMD_RTO_MAX_HOLD 200
#define SDMMC_WAIT_FOR_UNBUSY 2500
#ifdef CONFIG_MMC_DW_IDMAC
static void dw_mci_disable_low_power(struct dw_mci_slot *slot);
/*printk the all register of current host*/
+#if 0
static int dw_mci_regs_printk(struct dw_mci *host)
{
struct sdmmc_reg *regs = dw_mci_regs;
printk("=======printk %s-register end =========\n", mmc_hostname(host->mmc));
return 0;
}
-
+#endif
#if defined(CONFIG_DEBUG_FS)
static int dw_mci_req_show(struct seq_file *s, void *v)
return cmdr;
}
+#if 0
static u32 dw_mci_prep_stop_abort(struct dw_mci *host, struct mmc_command *cmd)
{
struct mmc_command *stop;
return cmdr;
}
-
+#endif
static void dw_mci_start_command(struct dw_mci *host,
struct mmc_command *cmd, u32 cmd_flags)
{
- unsigned long time_loop = jiffies + msecs_to_jiffies(5000);
- unsigned int status;
- bool ret=0;
-
- host->pre_cmd = host->cmd;
+ struct dw_mci_slot *slot = host->slot[0];
+ /*temporality fix slot[0] due to host->num_slots equal to 1*/
+
+ host->pre_cmd = host->cmd;
host->cmd = cmd;
dev_vdbg(host->dev,
- "start command: ARGR=0x%08x CMDR=0x%08x\n",
- cmd->arg, cmd_flags);
-
- if(SD_SWITCH_VOLTAGE == cmd->opcode){
- /*confirm non-low-power mode*/
- struct dw_mci_slot *slot = host->slot[0];//temporality fix slot[0] due to host->num_slots equal to 1;
- mci_writel(host, CMDARG, 0);
- dw_mci_disable_low_power(slot);
- MMC_DBG_INFO_FUNC(host->mmc,"Line%d..%s before start cmd=11,[%s]",
- __LINE__, __FUNCTION__,mmc_hostname(host->mmc));
-
- cmd_flags |= SDMMC_CMD_VOLT_SWITCH;
- }
+ "start command: ARGR=0x%08x CMDR=0x%08x\n",
+ cmd->arg, cmd_flags);
+
+ if(SD_SWITCH_VOLTAGE == cmd->opcode){
+ /*confirm non-low-power mode*/
+ mci_writel(host, CMDARG, 0);
+ dw_mci_disable_low_power(slot);
+
+ MMC_DBG_INFO_FUNC(host->mmc,"Line%d..%s before start cmd=11,[%s]",
+ __LINE__, __FUNCTION__,mmc_hostname(host->mmc));
+
+ cmd_flags |= SDMMC_CMD_VOLT_SWITCH;
+ }
mci_writel(host, CMDARG, cmd->arg);
wmb();
- if(host->mmc->hold_reg_flag)
- cmd_flags |= SDMMC_CMD_USE_HOLD_REG;//fix the value to 1 in some Soc,for example RK3188.
-
+
+ /* fix the value to 1 in some Soc,for example RK3188. */
+ if(host->mmc->hold_reg_flag)
+ cmd_flags |= SDMMC_CMD_USE_HOLD_REG;
+
mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
- wmb();
-
-#if 0//test
- while ((time_before(jiffies, time_loop))&&(test_bit(DW_MMC_CARD_PRESENT, &host->cur_slot->flags))){
- status = mci_readl(host, STATUS);
- if (!(status & (SDMMC_STAUTS_DATA_BUSY|SDMMC_STAUTS_MC_BUSY))){
- ret = 1 ;//card is unbusy
- break;
- }
- } ;
- if(!ret)
- MMC_DBG_ERR_FUNC(host->mmc,"Line%d..%s start cmd=%d(arg=0x%x), cmd_reg=0x%x, unbusy=%d,card-present=%d. [%s]",
- __LINE__, __FUNCTION__,cmd->opcode, cmd->arg,cmd_flags,
- ret,test_bit(DW_MMC_CARD_PRESENT, &host->cur_slot->flags), mmc_hostname(host->mmc));
-#endif
+ wmb();
}
static void send_stop_cmd(struct dw_mci *host, struct mmc_data *data)
mci_writel(host, BMOD, temp);
}
-static void dw_mci_idmac_complete_dma(struct dw_mci *host)
+static void dw_mci_idmac_complete_dma(void *arg)
{
- struct mmc_data *data = host->data;
+ struct dw_mci *host = arg;
+ struct mmc_data *data = host->data;
- dev_vdbg(host->dev, "DMA complete\n");
+ dev_vdbg(host->dev, "DMA complete\n");
- /*
- MMC_DBG_CMD_FUNC(host->mmc," DMA complete cmd=%d(arg=0x%x), blocks=%d,blksz=%d[%s]", \
- host->mrq->cmd->opcode,host->mrq->cmd->arg,data->blocks,data->blksz,mmc_hostname(host->mmc));
- */
-
- host->dma_ops->cleanup(host);
+ /*
+ MMC_DBG_CMD_FUNC(host->mmc," DMA complete cmd=%d(arg=0x%x), blocks=%d,blksz=%d[%s]", \
+ host->mrq->cmd->opcode,host->mrq->cmd->arg,
+ data->blocks,data->blksz,mmc_hostname(host->mmc));
+ */
+
+ host->dma_ops->cleanup(host);
/*
* If the card was removed, data will be NULL. No point in trying to
* send the stop command or waiting for NBUSY in this case.
*/
- if (data) {
- set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
- tasklet_schedule(&host->tasklet);
- }
+ if(data){
+ set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
+ tasklet_schedule(&host->tasklet);
+ }
}
static void dw_mci_translate_sglist(struct dw_mci *host, struct mmc_data *data,
.complete = dw_mci_idmac_complete_dma,
.cleanup = dw_mci_dma_cleanup,
};
+
+
+static void dw_mci_edma_cleanup(struct dw_mci *host)
+{
+ struct mmc_data *data = host->data;
+
+ if (data)
+ if (!data->host_cookie)
+ dma_unmap_sg(host->dev,
+ data->sg, data->sg_len,
+ dw_mci_get_dma_dir(data));
+}
+
+static void dw_mci_edmac_stop_dma(struct dw_mci *host)
+{
+ dmaengine_terminate_all(host->dms->ch);
+}
+
+static void dw_mci_edmac_complete_dma(void *arg)
+{
+ struct dw_mci *host = arg;
+ struct mmc_data *data = host->data;
+
+ dev_vdbg(host->dev, "DMA complete\n");
+
+ if(data)
+ if(data->flags & MMC_DATA_READ)
+ /* Invalidate cache after read */
+ dma_sync_sg_for_cpu(mmc_dev(host->mmc), data->sg,
+ data->sg_len, DMA_FROM_DEVICE);
+
+ host->dma_ops->cleanup(host);
+
+ /*
+ * If the card was removed, data will be NULL. No point in trying to
+ * send the stop command or waiting for NBUSY in this case.
+ */
+ if (data) {
+ set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
+ tasklet_schedule(&host->tasklet);
+ }
+}
+
+static void dw_mci_edmac_start_dma(struct dw_mci *host, unsigned int sg_len)
+{
+ struct dma_slave_config slave_config;
+ struct dma_async_tx_descriptor *desc = NULL;
+ struct scatterlist *sgl = host->data->sg;
+ u32 sg_elems = host->data->sg_len;
+ int ret = 0;
+
+ /* Set external dma config: burst size, burst width*/
+ slave_config.dst_addr = (dma_addr_t)(host->phy_regs + host->data_offset);
+ slave_config.src_addr = slave_config.dst_addr;
+ slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ slave_config.src_addr_width = slave_config.dst_addr_width;
+
+ /* Match FIFO dma burst MSIZE with external dma config*/
+ slave_config.dst_maxburst = ((host->fifoth_val) >> 28) && 0x7;
+ slave_config.src_maxburst = slave_config.dst_maxburst;
+
+ if(host->data->flags & MMC_DATA_WRITE){
+ slave_config.direction = DMA_MEM_TO_DEV;
+ ret = dmaengine_slave_config(host->dms->ch, &slave_config);
+ if(ret){
+ dev_err(host->dev, "error in dw_mci edma configuration.\n");
+ return;
+ }
+
+ desc = dmaengine_prep_slave_sg(host->dms->ch, sgl, sg_len,
+ DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if(!desc){
+ dev_err(host->dev, "We cannot prepare for the dw_mci slave edma!\n");
+ return;
+ }
+ /* Set dw_mci_edmac_complete_dma as callback */
+ desc->callback = dw_mci_edmac_complete_dma;
+ desc->callback_param = (void *)host;
+ dmaengine_submit(desc);
+
+ /* Flush cache before write */
+ dma_sync_sg_for_device(mmc_dev(host->mmc), sgl,
+ sg_elems, DMA_TO_DEVICE);
+ dma_async_issue_pending(host->dms->ch);
+ }else{
+ /* MMC_DATA_READ*/
+ slave_config.direction = DMA_DEV_TO_MEM;
+ ret = dmaengine_slave_config(host->dms->ch, &slave_config);
+ if(ret){
+ dev_err(host->dev, "error in dw_mci edma configuration.\n");
+ return;
+ }
+ desc = dmaengine_prep_slave_sg(host->dms->ch, sgl, sg_len,
+ DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if(!desc){
+ dev_err(host->dev, "We cannot prepare for the dw_mci slave edma!\n");
+ return;
+ }
+ /* set dw_mci_edmac_complete_dma as callback */
+ desc->callback = dw_mci_edmac_complete_dma;
+ desc->callback_param = (void *)host;
+ dmaengine_submit(desc);
+ dma_async_issue_pending(host->dms->ch);
+ }
+}
+
+static int dw_mci_edmac_init(struct dw_mci *host)
+{
+ /* Request external dma channel, SHOULD decide chn in dts */
+ host->dms = NULL;
+ host->dms = (struct dw_mci_dma_slave *)kmalloc
+ (sizeof(struct dw_mci_dma_slave), GFP_KERNEL);
+ if (NULL == host->dms) {
+ dev_err(host->dev, "No enough memory to alloc dms.\n");
+ goto err_exit;
+ }
+
+ host->dms->ch = dma_request_slave_channel(host->dev, "dw_mci");
+ if (!host->dms->ch) {
+ dev_err(host->dev, "Failed to get external DMA channel: channel id = %d\n",
+ host->dms->ch->chan_id);
+ goto err_exit;
+ }
+
+ return 0;
+
+err_exit:
+ if (NULL != host->dms) {
+ kfree(host->dms);
+ host->dms = NULL;
+ }
+ return -ENXIO;
+
+}
+
+static void dw_mci_edmac_exit(struct dw_mci *host)
+{
+ if (NULL != host->dms) {
+ if (NULL != host->dms->ch) {
+ dma_release_channel(host->dms->ch);
+ host->dms->ch = NULL;
+ }
+ kfree(host->dms);
+ host->dms = NULL;
+ }
+}
+
+static const struct dw_mci_dma_ops dw_mci_edmac_ops = {
+ .init = dw_mci_edmac_init,
+ .exit = dw_mci_edmac_exit,
+ .start = dw_mci_edmac_start_dma,
+ .stop = dw_mci_edmac_stop_dma,
+ .complete = dw_mci_edmac_complete_dma,
+ .cleanup = dw_mci_edma_cleanup,
+};
#endif /* CONFIG_MMC_DW_IDMAC */
static int dw_mci_pre_dma_transfer(struct dw_mci *host,
unsigned long timeout = jiffies + msecs_to_jiffies(500);//msecs_to_jiffies(5000);
unsigned int cmd_status = 0;
#ifdef SDMMC_WAIT_FOR_UNBUSY
+ bool ret = true;
timeout = jiffies + msecs_to_jiffies(SDMMC_WAIT_FOR_UNBUSY);
- bool ret=0;
+
if(test_bit(DW_MMC_CARD_PRESENT, &slot->flags)) {
- while (ret=time_before(jiffies, timeout)) {
+ while (ret) {
+ ret = time_before(jiffies, timeout);
cmd_status = mci_readl(host, STATUS);
if (!(cmd_status & (SDMMC_STAUTS_DATA_BUSY|SDMMC_STAUTS_MC_BUSY)))
break;
} ;
- if(!ret)
+ if(false == ret)
printk("%d..%s: wait for unbusy timeout.......[%s]\n", \
__LINE__, __FUNCTION__, mmc_hostname(host->mmc));
}
mci_writel(host, CMDARG, arg);
wmb();
mci_writel(host, CMD, SDMMC_CMD_START | cmd);
-
+ if(cmd & SDMMC_CMD_UPD_CLK)
+ timeout = jiffies + msecs_to_jiffies(50);
+ else
+ timeout = jiffies + msecs_to_jiffies(500);
while (time_before(jiffies, timeout)) {
cmd_status = mci_readl(host, CMD);
if (!(cmd_status & SDMMC_CMD_START))
- return;
+ return ;
}
dev_err(&slot->mmc->class_dev,
"Timeout sending command (cmd %#x arg %#x status %#x)\n",
u32 div;
u32 clk_en_a;
u32 sdio_int;
-
- MMC_DBG_INFO_FUNC(host->mmc,"%d..%s: clock=%d, current_speed=%d, bus_hz=%d,forc=%d[%s]\n",
- __LINE__, __FUNCTION__, clock, host->current_speed,host->bus_hz,force_clkinit,mmc_hostname(host->mmc));
+
+ MMC_DBG_INFO_FUNC(host->mmc,"%d..%s: clock=%d, current_speed=%d, bus_hz=%d,forc=%d[%s]\n",
+ __LINE__, __FUNCTION__, clock, host->current_speed,host->bus_hz,force_clkinit,mmc_hostname(host->mmc));
if (!clock) {
mci_writel(host, CLKENA, 0);
- mci_send_cmd(slot,
- SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
+ #ifdef CONFIG_MMC_DW_ROCKCHIP_SWITCH_VOLTAGE
+ if(host->svi_flags == 0)
+ mci_send_cmd(slot, SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
+ #else
+ mci_send_cmd(slot, SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
+ #endif
} else if (clock != host->current_speed || force_clkinit) {
div = host->bus_hz / clock;
if (host->bus_hz % clock && host->bus_hz > clock)
tempck, div);
host->set_speed = tempck;
- host->set_div = div;
+ host->set_div = div;
}
/* disable clock */
/* inform CIU */
mci_send_cmd(slot,
SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
-
+
+ if(clock <= 400*1000){
+ MMC_DBG_BOOT_FUNC(host->mmc,
+ "dw_mci_setup_bus: argue clk_mmc workaround out %dHz for init[%s]",
+ clock * 2, mmc_hostname(host->mmc));
+ /* clk_mmc will change parents to 24MHz xtal*/
+ clk_set_rate(host->clk_mmc, clock * 2);
+
+ div = 0;
+ host->set_div = div;
+ }
+ else
+ {
+ MMC_DBG_BOOT_FUNC(host->mmc,
+ "dw_mci_setup_bus: argue clk_mmc workaround out normal clock [%s]",
+ mmc_hostname(host->mmc));
+ if(div > 1)
+ {
+ MMC_DBG_ERR_FUNC(host->mmc,
+ "dw_mci_setup_bus: div SHOULD NOT LARGER THAN ONE! [%s]",
+ mmc_hostname(host->mmc));
+ div = 1;
+ host->set_div = div;
+ host->bus_hz = host->set_speed * 2;
+ MMC_DBG_BOOT_FUNC(host->mmc,
+ "dw_mci_setup_bus: workaround div = %d, host->bus_hz = %d [%s]",
+ div, host->bus_hz, mmc_hostname(host->mmc));
+ }
+ /* BUG may be here, come on, Linux BSP engineer looks!
+ FIXME: HS-DDR eMMC, div SHOULD be ONE, but we here cannot fetch eMMC bus mode!!!!!!!!
+ WRONG dts set clk = 50M, and calc div be zero. Controller denied this setting!
+ some oops happened like that:
+ mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
+ rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc0]
+ rk_sdmmc: BOOT Bus speed=50000000Hz,Bus width=8bits.[mmc0]
+ mmc0: new high speed DDR MMC card at address 0001
+ mmcblk0: mmc0:0001 M8G1GC 7.28 GiB
+ ....
+ mmcblk0: error -84 transferring data, sector 606208, nr 32, cmd response 0x900, card status 0xb00
+ mmcblk0: retrying using single block read
+ mmcblk0: error -110 sending status command, retrying
+
+ We assume all eMMC in RK platform with 3.10 kernel, at least version 4.5
+ */
+ if ((div == 0) &&
+ (host->mmc->caps & (MMC_CAP_1_8V_DDR | MMC_CAP_1_2V_DDR)) &&
+ !(host->mmc->caps2 & MMC_CAP2_HS200)) {
+ /* Fixup DDR MMC */
+ div = 1;
+ host->set_div = div;
+ host->bus_hz = host->set_speed * 2;
+ MMC_DBG_BOOT_FUNC(host->mmc,
+ "dw_mci_setup_bus: workaround div = %d, host->bus_hz = %d [%s]",
+ div, host->bus_hz, mmc_hostname(host->mmc));
+ }
+
+ if (host->verid < DW_MMC_240A)
+ clk_set_rate(host->clk_mmc,(host->bus_hz));
+ else
+ clk_set_rate(host->clk_mmc,(host->bus_hz) * 2);
+
+
+
+ }
+
/* set clock to desired speed */
mci_writel(host, CLKDIV, div);
if (host->verid < DW_MMC_240A)
sdio_int = SDMMC_INT_SDIO(slot->id);
- else
+ else
sdio_int = SDMMC_INT_SDIO((slot->id) + 8);
if (!(mci_readl(host, INTMASK) & sdio_int))
/* inform CIU */
mci_send_cmd(slot,
SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
-
/* keep the clock with reflecting clock dividor */
slot->__clk_old = clock << div;
}
/* Set the current slot bus width */
mci_writel(host, CTYPE, (slot->ctype << slot->id));
-
}
+extern struct mmc_card *this_card;
static void dw_mci_wait_unbusy(struct dw_mci *host)
{
- unsigned int timeout= SDMMC_DATA_TIMEOUT_SDIO;
- unsigned long time_loop;
- unsigned int status;
+ unsigned int timeout= SDMMC_DATA_TIMEOUT_SDIO;
+ unsigned long time_loop;
+ unsigned int status;
+ u32 se_flag = 0;
- MMC_DBG_INFO_FUNC(host->mmc, "dw_mci_wait_unbusy, status=0x%x ", mci_readl(host, STATUS));
+ MMC_DBG_INFO_FUNC(host->mmc, "dw_mci_wait_unbusy, status=0x%x ", mci_readl(host, STATUS));
- if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_EMMC)
- timeout = SDMMC_DATA_TIMEOUT_EMMC;
- else if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD)
- timeout = SDMMC_DATA_TIMEOUT_SD;
+ if (host->mmc->restrict_caps & RESTRICT_CARD_TYPE_EMMC) {
+ if (host->cmd && (host->cmd->opcode == MMC_ERASE)) {
+ /* Special care for (secure)erase timeout calculation */
+ if(this_card){
+ if((host->cmd->arg & (0x1 << 31)) == 1) /* secure erase */
+ se_flag = 0x1;
+
+ if (((this_card->ext_csd.erase_group_def) & 0x1) == 1) ;
+ se_flag ? (timeout = (this_card->ext_csd.hc_erase_timeout) *
+ 300000 * (this_card->ext_csd.sec_erase_mult)) :
+ (timeout = (this_card->ext_csd.hc_erase_timeout) * 300000);
+ }
+ }
- time_loop = jiffies + msecs_to_jiffies(timeout);
- do {
- status = mci_readl(host, STATUS);
- if (!(status & (SDMMC_STAUTS_DATA_BUSY|SDMMC_STAUTS_MC_BUSY)))
- break;
- //MMC_DBG_INFO_FUNC("dw_mci_wait_unbusy, waiting for......");
- } while (time_before(jiffies, time_loop));
+ if(timeout < SDMMC_DATA_TIMEOUT_EMMC)
+ timeout = SDMMC_DATA_TIMEOUT_EMMC;
+ } else if (host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD) {
+ timeout = SDMMC_DATA_TIMEOUT_SD;
+ }
+
+ time_loop = jiffies + msecs_to_jiffies(timeout);
+ do {
+ status = mci_readl(host, STATUS);
+ if (!(status & (SDMMC_STAUTS_DATA_BUSY | SDMMC_STAUTS_MC_BUSY)))
+ break;
+ } while (time_before(jiffies, time_loop));
}
+
+
+#ifdef CONFIG_MMC_DW_ROCKCHIP_SWITCH_VOLTAGE
/*
* result:
* 0--status is busy.
{
struct dw_mci_slot *slot = mmc_priv(mmc);
struct dw_mci *host = slot->host;
- unsigned int timeout= SDMMC_DATA_TIMEOUT_SDIO;
- unsigned long time_loop;
- unsigned int status;
- int ret= 0;
+
+ MMC_DBG_INFO_FUNC(host->mmc, "dw_mci_card_busy: svi_flags = %d [%s]", \
+ host->svi_flags, mmc_hostname(host->mmc));
- if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_EMMC)
- timeout = SDMMC_DATA_TIMEOUT_EMMC;
- else if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD)
- timeout = SDMMC_DATA_TIMEOUT_SD;
- timeout = 250*1000;//test
- time_loop = jiffies + msecs_to_jiffies(timeout);
+ /* svi toggle*/
+ if(host->svi_flags == 0){
+ /*first svi*/
+ host->svi_flags = 1;
+ return host->svi_flags;
- MMC_DBG_INFO_FUNC(host->mmc, "line%d: dw_mci_wait_unbusy,timeloop=%lu, status=0x%x ",
- __LINE__, time_loop, mci_readl(host, STATUS));
- do {
- status = mci_readl(host, STATUS);
- if (!(status & (SDMMC_STAUTS_DATA_BUSY|SDMMC_STAUTS_MC_BUSY))){
- ret = 1;//card is unbusy.
- break;
+ }else{
+ host->svi_flags = 0;
+ return host->svi_flags;
}
- //MMC_DBG_INFO_FUNC("dw_mci_wait_unbusy, waiting for......");
- } while (time_before(jiffies, time_loop));
- MMC_DBG_INFO_FUNC(host->mmc, "line%d: dw_mci_wait_unbusy,ret=%d, status=0x%x ",
- __LINE__,ret,mci_readl(host, STATUS));
+
- return ret;
}
-
+#endif
static void __dw_mci_start_request(struct dw_mci *host,
struct dw_mci_slot *slot,
struct mmc_command *cmd)
host->cur_slot = slot;
host->mrq = mrq;
-#if 0 //add by xbw,at 2014-03-12
- /*clean FIFO if it is a new request*/
- if(!(mrq->cmd->opcode & SDMMC_CMD_STOP)) {
- MMC_DBG_INFO_FUNC("%d..%s: reset the ctrl.", __LINE__, __FUNCTION__);
- mci_writel(host, CTRL, (SDMMC_CTRL_RESET | SDMMC_CTRL_FIFO_RESET |
- SDMMC_CTRL_DMA_RESET));
- }
- #endif
- dw_mci_wait_unbusy(host);
+
+ dw_mci_wait_unbusy(host);
host->pending_events = 0;
host->completed_events = 0;
{
struct mmc_request *mrq = slot->mrq;
struct mmc_command *cmd;
-
- MMC_DBG_INFO_FUNC(host->mmc, " Begin to start the new request. cmd=%d(arg=0x%x)[%s]", \
- mrq->cmd->opcode, mrq->cmd->arg, mmc_hostname(host->mmc));
+
+ MMC_DBG_INFO_FUNC(host->mmc, " Begin to start the new request. cmd=%d(arg=0x%x)[%s]", \
+ mrq->cmd->opcode, mrq->cmd->arg, mmc_hostname(host->mmc));
cmd = mrq->sbc ? mrq->sbc : mrq->cmd;
__dw_mci_start_request(host, slot, cmd);
mmc_request_done(mmc, mrq);
return;
}
- MMC_DBG_CMD_FUNC(host->mmc, "======>\n pull a new request from MMC-frame to dw_mci_queue. cmd=%d(arg=0x%x)[%s]", \
- mrq->cmd->opcode, mrq->cmd->arg, mmc_hostname(host->mmc));
+
+ MMC_DBG_CMD_FUNC(host->mmc, "======>\n pull a new request from MMC-frame to dw_mci_queue. cmd=%d(arg=0x%x)[%s]", \
+ mrq->cmd->opcode, mrq->cmd->arg, mmc_hostname(host->mmc));
dw_mci_queue_request(host, slot, mrq);
static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
{
struct dw_mci_slot *slot = mmc_priv(mmc);
+ #ifdef CONFIG_MMC_DW_ROCKCHIP_SWITCH_VOLTAGE
+ struct dw_mci *host = slot->host;
+ #endif
const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
u32 regs;
-#ifdef SDMMC_WAIT_FOR_UNBUSY
- unsigned long time_loop = jiffies + msecs_to_jiffies(SDMMC_WAIT_FOR_UNBUSY);
- bool ret=0;
-
- if(!test_bit(DW_MMC_CARD_PRESENT, &slot->flags)){
- printk("%d..%s: no card. [%s]\n", \
- __LINE__, __FUNCTION__, mmc_hostname(mmc));
- goto EXIT_POWER;
- }
+
+ #ifdef SDMMC_WAIT_FOR_UNBUSY
+ unsigned long time_loop;
+ bool ret = true;
+
+ #ifdef CONFIG_MMC_DW_ROCKCHIP_SWITCH_VOLTAGE
+ if(host->svi_flags == 1)
+ time_loop = jiffies + msecs_to_jiffies(SDMMC_DATA_TIMEOUT_SD);
+ else
+ time_loop = jiffies + msecs_to_jiffies(SDMMC_WAIT_FOR_UNBUSY);
+ #else
+ time_loop = jiffies + msecs_to_jiffies(SDMMC_WAIT_FOR_UNBUSY);
+ #endif
+
+ if(!test_bit(DW_MMC_CARD_PRESENT, &slot->flags)){
+ printk("%d..%s: no card. [%s]\n", \
+ __LINE__, __FUNCTION__, mmc_hostname(mmc));
+ goto EXIT_POWER;
+ }
- while (ret=time_before(jiffies, time_loop)) {
- regs = mci_readl(slot->host, STATUS);
- if (!(regs & (SDMMC_STAUTS_DATA_BUSY|SDMMC_STAUTS_MC_BUSY)))
- break;
- } ;
- if(!ret)
- {
- printk("slot->flags=%d ", slot->flags);
- dump_stack();
- printk("%d..%s: wait for unbusy timeout.......[%s]\n", \
- __LINE__, __FUNCTION__, mmc_hostname(mmc));
- }
-#endif
+ while (ret) {
+ ret = time_before(jiffies, time_loop);
+ regs = mci_readl(slot->host, STATUS);
+ if (!(regs & (SDMMC_STAUTS_DATA_BUSY|SDMMC_STAUTS_MC_BUSY)))
+ break;
+ };
+
+ if(false == ret)
+ {
+ printk("slot->flags = %lu ", slot->flags);
+ #ifdef CONFIG_MMC_DW_ROCKCHIP_SWITCH_VOLTAGE
+ if(host->svi_flags != 1)
+ #endif
+ dump_stack();
+ printk("%d..%s: wait for unbusy timeout....... STATUS = 0x%x [%s]\n", \
+ __LINE__, __FUNCTION__, regs, mmc_hostname(mmc));
+ }
+ #endif
+
switch (ios->bus_width) {
case MMC_BUS_WIDTH_4:
slot->ctype = SDMMC_CTYPE_4BIT;
/* Slot specific timing and width adjustment */
dw_mci_setup_bus(slot, false);
+ //return -EAGAIN;
EXIT_POWER:
switch (ios->power_mode) {
- case MMC_POWER_UP:
- set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
- /* Power up slot */
- if (slot->host->pdata->setpower)
- slot->host->pdata->setpower(slot->id, mmc->ocr_avail);
- regs = mci_readl(slot->host, PWREN);
- regs |= (1 << slot->id);
- mci_writel(slot->host, PWREN, regs);
- break;
- case MMC_POWER_OFF:
- /* Power down slot */
- if (slot->host->pdata->setpower)
- slot->host->pdata->setpower(slot->id, 0);
- regs = mci_readl(slot->host, PWREN);
- regs &= ~(1 << slot->id);
- mci_writel(slot->host, PWREN, regs);
- break;
- default:
- break;
+ case MMC_POWER_UP:
+ set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
+ /* Power up slot */
+ if (slot->host->pdata->setpower)
+ slot->host->pdata->setpower(slot->id, mmc->ocr_avail);
+ regs = mci_readl(slot->host, PWREN);
+ regs |= (1 << slot->id);
+ mci_writel(slot->host, PWREN, regs);
+ break;
+ case MMC_POWER_OFF:
+ /* Power down slot */
+ if(slot->host->pdata->setpower)
+ slot->host->pdata->setpower(slot->id, 0);
+ regs = mci_readl(slot->host, PWREN);
+ regs &= ~(1 << slot->id);
+ mci_writel(slot->host, PWREN, regs);
+ break;
+ default:
+ break;
}
}
struct dw_mci_board *brd = slot->host->pdata;
/* Use platform get_ro function, else try on board write protect */
- if (slot->quirks & DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT)
+ if(slot->quirks & DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT)
read_only = 0;
- else if (brd->get_ro)
+ else if(brd->get_ro)
read_only = brd->get_ro(slot->id);
- else if (gpio_is_valid(slot->wp_gpio))
+ else if(gpio_is_valid(slot->wp_gpio))
read_only = gpio_get_value(slot->wp_gpio);
else
read_only =
static int dw_mci_set_sdio_status(struct mmc_host *mmc, int val)
{
- struct dw_mci_slot *slot = mmc_priv(mmc);
- struct dw_mci_board *brd = slot->host->pdata;
- struct dw_mci *host = slot->host;
- if (!(mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO))
- return 0;
-
- spin_lock_bh(&host->lock);
- if(val)
- set_bit(DW_MMC_CARD_PRESENT, &slot->flags);
- else
- clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
-
- spin_unlock_bh(&host->lock);
-
- mmc_detect_change(slot->mmc, 20);
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ /*struct dw_mci_board *brd = slot->host->pdata;*/
- return 0;
+ if (!(mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO))
+ return 0;
+
+ spin_lock_bh(&host->lock);
+
+ if(val)
+ set_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+ else
+ clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+
+ spin_unlock_bh(&host->lock);
+
+ if(test_bit(DW_MMC_CARD_PRESENT, &slot->flags)){
+ if(__clk_is_enabled(host->hclk_mmc) == false)
+ clk_prepare_enable(host->hclk_mmc);
+ if(__clk_is_enabled(host->clk_mmc) == false)
+ clk_prepare_enable(host->clk_mmc);
+ }else{
+ if(__clk_is_enabled(host->clk_mmc) == true)
+ clk_disable_unprepare(slot->host->clk_mmc);
+ if(__clk_is_enabled(host->hclk_mmc) == true)
+ clk_disable_unprepare(slot->host->hclk_mmc);
+ }
+
+ mmc_detect_change(slot->mmc, 20);
+ return 0;
}
static int dw_mci_get_cd(struct mmc_host *mmc)
{
- int present;
- struct dw_mci_slot *slot = mmc_priv(mmc);
- struct dw_mci_board *brd = slot->host->pdata;
- struct dw_mci *host = slot->host;
- int gpio_cd = mmc_gpio_get_cd(mmc);
-
- if (mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO)
- return test_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+ int present;
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci_board *brd = slot->host->pdata;
+ struct dw_mci *host = slot->host;
+ int gpio_cd = mmc_gpio_get_cd(mmc);
+ int gpio_val;
+
+ if (cpu_is_rk312x() &&
+ soc_is_rk3126() &&
+ (mmc->restrict_caps & RESTRICT_CARD_TYPE_SD)) {
+ gpio_cd = slot->cd_gpio;
+ if (gpio_is_valid(gpio_cd)) {
+ gpio_val = gpio_get_value_cansleep(gpio_cd);
+ msleep(10);
+ if (gpio_val == gpio_get_value_cansleep(gpio_cd)) {
+ gpio_cd = gpio_get_value_cansleep(gpio_cd) == 0 ? 1 : 0;
+ if (gpio_cd == 0) {
+ /* Enable force_jtag wihtout card in slot, ONLY for NCD-package */
+ grf_writel((0x1 << 24) | (1 << 8), RK312X_GRF_SOC_CON0);
+ dw_mci_ctrl_all_reset(host);
+ } else {
+ /* Really card detected: SHOULD disable force_jtag */
+ grf_writel((0x1 << 24) | (0 << 8), RK312X_GRF_SOC_CON0);
+ }
+ } else {
+ /* Jitter */
+ return slot->last_detect_state;
+ }
+ } else {
+ dev_err(host->dev, "dw_mci_get_cd: invalid gpio_cd!\n");
+ }
+ }
+
+ if (mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO)
+ return test_bit(DW_MMC_CARD_PRESENT, &slot->flags);
/* Use platform get_cd function, else try onboard card detect */
if (brd->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION)
return present;
}
+
+/*
+ * Dts Should caps emmc controller with poll-hw-reset
+ */
static void dw_mci_hw_reset(struct mmc_host *mmc)
{
- struct dw_mci_slot *slot = mmc_priv(mmc);
-
- /*
- * According to eMMC spec
- * tRstW >= 1us ; RST_n pulse width
- * tRSCA >= 200us ; RST_n to Command time
- * tRSTH >= 1us ; RST_n high period
- */
-
- mci_writel(slot->host, RST_n, 0x1);
- dsb();
- udelay(10); //10us for bad quality eMMc.
-
- mci_writel(slot->host, RST_n, 0x0);
- dsb();
- usleep_range(300, 1000); //ay least 300(> 200us)
-
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ u32 regs;
+
+ #if 0
+ u32 cmd_flags;
+ unsigned long timeout;
+ bool ret = true;
+
+ /* (1) CMD12 to end any transfer in process */
+ cmd_flags = SDMMC_CMD_STOP | SDMMC_CMD_RESP_CRC
+ | SDMMC_CMD_RESP_EXP | MMC_STOP_TRANSMISSION;
+
+ if(host->mmc->hold_reg_flag)
+ cmd_flags |= SDMMC_CMD_USE_HOLD_REG;
+ mci_writel(host, CMDARG, 0);
+ wmb();
+ mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
+ wmb();
+ timeout = jiffies + msecs_to_jiffies(500);
+ while(ret){
+ ret = time_before(jiffies, timeout);
+ if(!(mci_readl(host, CMD) & SDMMC_CMD_START))
+ break;
+ }
+
+ if(false == ret)
+ MMC_DBG_ERR_FUNC(host->mmc,
+ "%s dw_mci_hw_reset: STOP_TRANSMISSION failed!!! [%s]\n",
+ __func__, mmc_hostname(host->mmc));
+
+ /* (2) wait DTO, even if no response is sent back by card */
+ ret = true;
+ timeout = jiffies + msecs_to_jiffies(5);
+ while(ret){
+ ret = time_before(jiffies, timeout);
+ if(!(mci_readl(host, MINTSTS) & SDMMC_INT_DATA_OVER)){
+ mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
+ break;
+ }
+ }
+ #endif
+
+ /* (3) Reset following: DONNOT CHANGE RESET ORDER!*/
+
+ /* Software reset - BMOD[0] for IDMA only */
+ regs = mci_readl(host, BMOD);
+ regs |= SDMMC_IDMAC_SWRESET;
+ mci_writel(host, BMOD, regs);
+ udelay(1); /* Auto cleared after 1 cycle, 1us is enough for hclk_mmc */
+ regs = mci_readl(host, BMOD);
+ if(regs & SDMMC_IDMAC_SWRESET)
+ MMC_DBG_WARN_FUNC(host->mmc,
+ "%s dw_mci_hw_reset: SDMMC_IDMAC_SWRESET failed!!! [%s]\n",
+ __func__, mmc_hostname(host->mmc));
+
+ /* DMA reset - CTRL[2] */
+ regs = mci_readl(host, CTRL);
+ regs |= SDMMC_CTRL_DMA_RESET;
+ mci_writel(host, CTRL, regs);
+ udelay(1); /* Auto cleared after 2 AHB clocks, 1us is enough plus mci_readl access */
+ regs = mci_readl(host, CTRL);
+ if(regs & SDMMC_CTRL_DMA_RESET)
+ MMC_DBG_WARN_FUNC(host->mmc,
+ "%s dw_mci_hw_reset: SDMMC_CTRL_DMA_RESET failed!!! [%s]\n",
+ __func__, mmc_hostname(host->mmc));
+
+ /* FIFO reset - CTRL[1] */
+ regs = mci_readl(host, CTRL);
+ regs |= SDMMC_CTRL_FIFO_RESET;
+ mci_writel(host, CTRL, regs);
+ mdelay(1); /* no timing limited, 1ms is random value */
+ regs = mci_readl(host, CTRL);
+ if(regs & SDMMC_CTRL_FIFO_RESET)
+ MMC_DBG_WARN_FUNC(host->mmc,
+ "%s dw_mci_hw_reset: SDMMC_CTRL_DMA_RESET failed!!! [%s]\n",
+ __func__, mmc_hostname(host->mmc));
+
+ /* (4) CARD_RESET
+ According to eMMC spec
+ tRstW >= 1us ; RST_n pulse width
+ tRSCA >= 200us ; RST_n to Command time
+ tRSTH >= 1us ; RST_n high period
+ */
+ mci_writel(slot->host, PWREN, 0x0);
+ mci_writel(slot->host, RST_N, 0x0);
+ dsb();
+ udelay(10); /* 10us for bad quality eMMc. */
+
+ mci_writel(slot->host, PWREN, 0x1);
+ mci_writel(slot->host, RST_N, 0x1);
+ dsb();
+ usleep_range(500, 1000); /* at least 500(> 200us) */
}
/*
{
struct dw_mci_slot *slot = mmc_priv(mmc);
struct dw_mci *host = slot->host;
+ //unsigned long flags;
u32 int_mask;
u32 sdio_int;
+ //spin_lock_irqsave(&host->lock, flags);
+
/* Enable/disable Slot Specific SDIO interrupt */
int_mask = mci_readl(host, INTMASK);
- if (host->verid < DW_MMC_240A)
+ if (host->verid < DW_MMC_240A)
sdio_int = SDMMC_INT_SDIO(slot->id);
else
sdio_int = SDMMC_INT_SDIO((slot->id) + 8);
mci_writel(host, INTMASK,
(int_mask & ~sdio_int));
}
+
+ //spin_unlock_irqrestore(&host->lock, flags);
}
+#ifdef CONFIG_MMC_DW_ROCKCHIP_SWITCH_VOLTAGE
+enum{
+ IO_DOMAIN_12 = 1200,
+ IO_DOMAIN_18 = 1800,
+ IO_DOMAIN_33 = 3300,
+};
+static void dw_mci_do_grf_io_domain_switch(struct dw_mci *host, u32 voltage)
+{
+ switch(voltage){
+ case IO_DOMAIN_33:
+ voltage = 0;
+ break;
+ case IO_DOMAIN_18:
+ voltage = 1;
+ break;
+ case IO_DOMAIN_12:
+ MMC_DBG_ERR_FUNC(host->mmc,"%s : Not support io domain voltage [%s]\n",
+ __FUNCTION__, mmc_hostname(host->mmc));
+ break;
+ default:
+ MMC_DBG_ERR_FUNC(host->mmc,"%s : Err io domain voltage [%s]\n",
+ __FUNCTION__, mmc_hostname(host->mmc));
+ break;
+ }
+
+ if(cpu_is_rk3288()){
+ if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD)
+ grf_writel((voltage << 7) | (1 << 23), RK3288_GRF_IO_VSEL);
+ else
+ return ;
+ }else{
+ MMC_DBG_ERR_FUNC(host->mmc,"%s : unknown chip [%s]\n",
+ __FUNCTION__, mmc_hostname(host->mmc));
+ }
+}
static int dw_mci_do_start_signal_voltage_switch(struct dw_mci *host,
struct mmc_ios *ios)
return 0;
uhs_reg = mci_readl(host, UHS_REG);
- MMC_DBG_SW_VOL_FUNC(host->mmc,"%d..%s: vol=%d.[%s]\n",
- __LINE__, __FUNCTION__,ios->signal_voltage, mmc_hostname(host->mmc));
+ MMC_DBG_SW_VOL_FUNC(host->mmc,"%d..%s: vol=%d.[%s]\n",
+ __LINE__, __FUNCTION__,ios->signal_voltage, mmc_hostname(host->mmc));
switch (ios->signal_voltage) {
case MMC_SIGNAL_VOLTAGE_330:
/* Set 1.8V Signal Enable in the Host Control2 register to 0 */
if (host->vmmc) {
ret = io_domain_regulator_set_voltage(host->vmmc, 3300000, 3300000);
- //regulator_put(host->vmmc); //to be done in remove function.
+ /* regulator_put(host->vmmc); //to be done in remove function. */
MMC_DBG_SW_VOL_FUNC(host->mmc,"%s =%dmV set 3.3end, ret=%d \n",
__func__, regulator_get_voltage(host->vmmc), ret);
if (ret) {
- pr_warning("%s: Switching to 3.3V signalling voltage "
+ MMC_DBG_SW_VOL_FUNC(host->mmc, "%s: Switching to 3.3V signalling voltage "
" failed\n", mmc_hostname(host->mmc));
return -EIO;
}
+ dw_mci_do_grf_io_domain_switch(host, IO_DOMAIN_33);
}
- MMC_DBG_SW_VOL_FUNC(host->mmc,"%d..%s: [%s]\n",__LINE__, __FUNCTION__, mmc_hostname(host->mmc));
+ MMC_DBG_SW_VOL_FUNC(host->mmc,"%d..%s: [%s]\n",__LINE__,
+ __FUNCTION__, mmc_hostname(host->mmc));
- //set High-power mode
+ /* set High-power mode */
value = mci_readl(host, CLKENA);
- mci_writel(host,CLKENA , value& ~SDMMC_CLKEN_LOW_PWR);
- //SDMMC_UHS_REG
- mci_writel(host,UHS_REG , uhs_reg & ~SDMMC_UHS_VOLT_REG_18);
+ value &= ~SDMMC_CLKEN_LOW_PWR;
+ mci_writel(host,CLKENA , value);
+ /* SDMMC_UHS_REG */
+ uhs_reg &= ~SDMMC_UHS_VOLT_REG_18;
+ mci_writel(host,UHS_REG , uhs_reg);
/* Wait for 5ms */
usleep_range(5000, 5500);
/* 3.3V regulator output should be stable within 5 ms */
uhs_reg = mci_readl(host, UHS_REG);
- if( !(uhs_reg & SDMMC_UHS_VOLT_REG_18))
- return 0;
+ if( !(uhs_reg & SDMMC_UHS_VOLT_REG_18))
+ return 0;
- pr_warning("%s: 3.3V regulator output did not became stable\n",
+ MMC_DBG_SW_VOL_FUNC(host->mmc, "%s: 3.3V regulator output did not became stable\n",
mmc_hostname(host->mmc));
return -EAGAIN;
case MMC_SIGNAL_VOLTAGE_180:
if (host->vmmc) {
ret = io_domain_regulator_set_voltage(host->vmmc,1800000, 1800000);
-// regulator_put(host->vmmc);//to be done in remove function.
+ /* regulator_put(host->vmmc);//to be done in remove function. */
MMC_DBG_SW_VOL_FUNC(host->mmc,"%d..%s =%dmV set 1.8end, ret=%d . \n",
__LINE__, __func__, regulator_get_voltage(host->vmmc), ret);
if (ret) {
- pr_warning("%s: Switching to 1.8V signalling voltage "
+ MMC_DBG_SW_VOL_FUNC(host->mmc, "%s: Switching to 1.8V signalling voltage "
" failed\n", mmc_hostname(host->mmc));
return -EIO;
}
+ dw_mci_do_grf_io_domain_switch(host, IO_DOMAIN_18);
}
/*
* Enable 1.8V Signal Enable in the Host Control2
* register
*/
- mci_writel(host,UHS_REG , uhs_reg | SDMMC_UHS_VOLT_REG_18);
+ mci_writel(host,UHS_REG , uhs_reg | SDMMC_UHS_VOLT_REG_18);
/* Wait for 5ms */
usleep_range(5000, 5500);
- MMC_DBG_SW_VOL_FUNC(host->mmc,"%d..%s: .[%s]\n",__LINE__, __FUNCTION__,mmc_hostname(host->mmc));
+ MMC_DBG_SW_VOL_FUNC(host->mmc,"%d..%s: .[%s]\n",__LINE__,
+ __FUNCTION__,mmc_hostname(host->mmc));
/* 1.8V regulator output should be stable within 5 ms */
uhs_reg = mci_readl(host, UHS_REG);
- if( uhs_reg & SDMMC_UHS_VOLT_REG_18){
-
- return 0;
- }
-
- pr_warning("%s: 1.8V regulator output did not became stable\n",
+ if(uhs_reg & SDMMC_UHS_VOLT_REG_18)
+ return 0;
+
+ MMC_DBG_SW_VOL_FUNC(host->mmc, "%s: 1.8V regulator output did not became stable\n",
mmc_hostname(host->mmc));
return -EAGAIN;
if (host->vmmc) {
ret = io_domain_regulator_set_voltage(host->vmmc, 1200000, 1200000);
if (ret) {
- pr_warning("%s: Switching to 1.2V signalling voltage "
+ MMC_DBG_SW_VOL_FUNC(host->mmc, "%s: Switching to 1.2V signalling voltage "
" failed\n", mmc_hostname(host->mmc));
return -EIO;
}
if (host->verid < DW_MMC_240A)
return 0;
- //sdhci_runtime_pm_get(host);
+
err = dw_mci_do_start_signal_voltage_switch(host, ios);
- //sdhci_runtime_pm_put(host);
return err;
}
+#endif
+
static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode)
{
struct dw_mci_slot *slot = mmc_priv(mmc);
struct dw_mci_tuning_data tuning_data;
int err = -ENOSYS;
+ /* Fixme: 3036/3126 doesn't support 1.8 io domain, no sense exe tuning */
+ if(cpu_is_rk3036() || cpu_is_rk312x())
+ return err;
+
if (opcode == MMC_SEND_TUNING_BLOCK_HS200) {
if (mmc->ios.bus_width == MMC_BUS_WIDTH_8) {
tuning_data.blk_pattern = tuning_blk_pattern_8bit;
return -EINVAL;
}
- /////////////////////////////////////////////////
- //temporary settings,!!!!!!!!!!!!!!!
+
+ /* Recommend sample phase and delayline
+ Fixme: Mix-use these three controllers will cause
+ con_id mismatch.
+ */
if (mmc->restrict_caps & RESTRICT_CARD_TYPE_EMMC)
tuning_data.con_id = 3;
- else if (mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO)
+ else if(mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO)
tuning_data.con_id = 1;
else
- tuning_data.con_id = 0;
- tuning_data.tuning_type = 1; //0--drv, 1--sample
- /////////////////////////////////////////////////
+ tuning_data.con_id = 0;
+ /* 0: driver, from host->devices
+ 1: sample, from devices->host
+ */
+ tuning_data.tuning_type = 1;
+
if (drv_data && drv_data->execute_tuning)
err = drv_data->execute_tuning(slot, opcode, &tuning_data);
+
return err;
}
.hw_reset = dw_mci_hw_reset,
.enable_sdio_irq = dw_mci_enable_sdio_irq,
.execute_tuning = dw_mci_execute_tuning,
- //.start_signal_voltage_switch = dw_mci_start_signal_voltage_switch,
- //.card_busy = dw_mci_card_busy,
+ #ifdef CONFIG_MMC_DW_ROCKCHIP_SWITCH_VOLTAGE
+ .start_signal_voltage_switch = dw_mci_start_signal_voltage_switch,
+ .card_busy = dw_mci_card_busy,
+ #endif
};
+#if 0
static void dw_mci_enable_irq(struct dw_mci *host, bool irqflag)
{
unsigned long flags;
}
local_irq_restore(flags);
}
+#endif
static void dw_mci_deal_data_end(struct dw_mci *host, struct mmc_request *mrq)
__releases(&host->lock)
__acquires(&host->lock)
{
- if(DW_MCI_SEND_STATUS == host->dir_status){
+ if(DW_MCI_SEND_STATUS == host->dir_status){
#if 0
if( MMC_BUS_TEST_W != host->cmd->opcode){
if(host->data_status & SDMMC_INT_DCRC)
#else
dw_mci_wait_unbusy(host);
#endif
-
- }
+ }
}
static void dw_mci_request_end(struct dw_mci *host, struct mmc_request *mrq)
struct mmc_host *prev_mmc = host->cur_slot->mmc;
WARN_ON(host->cmd || host->data);
-
- dw_mci_deal_data_end(host, mrq);
- if(mrq->cmd)
- MMC_DBG_CMD_FUNC(host->mmc, " reqeust end--reqeuest done, cmd=%d, cmderr=%d, host->state=%d [%s]",\
- mrq->cmd->opcode,mrq->cmd->error, host->state,mmc_hostname(host->mmc));
- if(mrq->data)
- MMC_DBG_CMD_FUNC(host->mmc, " reqeust end--reqeuest done, cmd=%d, dataerr=%d, host->state=%d [%s]",\
- mrq->cmd->opcode,mrq->data->error, host->state, mmc_hostname(host->mmc));
+ del_timer_sync(&host->dto_timer);
+ dw_mci_deal_data_end(host, mrq);
+
+ if(mrq->cmd)
+ MMC_DBG_CMD_FUNC(host->mmc, " reqeust end--reqeuest done, cmd=%d, cmderr=%d, host->state=%d [%s]",\
+ mrq->cmd->opcode,mrq->cmd->error, host->state,mmc_hostname(host->mmc));
+ if(mrq->data)
+ MMC_DBG_CMD_FUNC(host->mmc, " reqeust end--reqeuest done, cmd=%d, dataerr=%d, host->state=%d [%s]",\
+ mrq->cmd->opcode,mrq->data->error, host->state, mmc_hostname(host->mmc));
host->cur_slot->mrq = NULL;
host->mrq = NULL;
host->state = STATE_IDLE;
}
- spin_unlock(&host->lock);
+ spin_unlock(&host->lock);
mmc_request_done(prev_mmc, mrq);
spin_lock(&host->lock);
}
{
if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO)
host->cmd_rto += 1;
-
- cmd->error = -ETIMEDOUT;
- }
- else if ((cmd->flags & MMC_RSP_CRC) && (status & SDMMC_INT_RCRC))
+
+ cmd->error = -ETIMEDOUT;
+ del_timer_sync(&host->dto_timer);
+ }else if ((cmd->flags & MMC_RSP_CRC) && (status & SDMMC_INT_RCRC)){
+ del_timer_sync(&host->dto_timer);
cmd->error = -EILSEQ;
- else if (status & SDMMC_INT_RESP_ERR)
+ }else if (status & SDMMC_INT_RESP_ERR){
+ del_timer_sync(&host->dto_timer);
cmd->error = -EIO;
- else
+ }else{
cmd->error = 0;
- MMC_DBG_CMD_FUNC(host->mmc, " command complete, cmd=%d,cmdError=%d [%s]",cmd->opcode, cmd->error,mmc_hostname(host->mmc));
+ }
+ MMC_DBG_CMD_FUNC(host->mmc, " command complete, cmd=%d,cmdError=%d [%s]",
+ cmd->opcode, cmd->error,mmc_hostname(host->mmc));
if (cmd->error) {
+ del_timer_sync(&host->dto_timer);
if(MMC_SEND_STATUS != cmd->opcode)
if(host->cmd_rto >= SDMMC_CMD_RTO_MAX_HOLD){
- MMC_DBG_ERR_FUNC(host->mmc, " command complete, cmd=%d,cmdError=%d [%s]",\
- cmd->opcode, cmd->error,mmc_hostname(host->mmc));
- host->cmd_rto = 0;
- }
+ MMC_DBG_CMD_FUNC(host->mmc, " command complete, cmd=%d,cmdError=%d [%s]",\
+ cmd->opcode, cmd->error,mmc_hostname(host->mmc));
+ host->cmd_rto = 0;
+ }
/* newer ip versions need a delay between retries */
if (host->quirks & DW_MCI_QUIRK_RETRY_DELAY)
static void dw_mci_tasklet_func(unsigned long priv)
{
struct dw_mci *host = (struct dw_mci *)priv;
- struct dw_mci_slot *slot = mmc_priv(host->mmc);
+ struct dw_mci_slot *slot = mmc_priv(host->mmc);
struct mmc_data *data;
struct mmc_command *cmd;
enum dw_mci_state state;
enum dw_mci_state prev_state;
- u32 status, ctrl, cmd_flags;
+ u32 status, cmd_flags;
+ unsigned long timeout = 0;
+ bool ret = true;
spin_lock(&host->lock);
goto unlock;
}
- if (cmd->data && cmd->error) {
+ if (cmd->data && cmd->error) {
+ del_timer_sync(&host->dto_timer); /* delete the timer for INT_DTO */
dw_mci_stop_dma(host);
#if 1
- if (data->stop) {
- send_stop_cmd(host, data);
- state = STATE_SENDING_STOP;
- break;
- } else {
- host->data = NULL;
- }
+ if (data->stop) {
+ send_stop_cmd(host, data);
+ state = STATE_SENDING_STOP;
+ break;
+ }else{
+ host->data = NULL;
+ }
#else
send_stop_abort(host, data);
state = STATE_SENDING_STOP;
break;
#endif
+ set_bit(EVENT_DATA_COMPLETE, &host->completed_events);
}
-
if (!host->mrq->data || cmd->error) {
dw_mci_request_end(host, host->mrq);
goto unlock;
/* fall through */
case STATE_SENDING_DATA:
- if (test_and_clear_bit(EVENT_DATA_ERROR,
- &host->pending_events)) {
+ if (test_and_clear_bit(EVENT_DATA_ERROR, &host->pending_events)) {
dw_mci_stop_dma(host);
#if 1
- if (data->stop)
+ if (data->stop){
send_stop_cmd(host, data);
- else{
- /*single block read/write, send stop cmd manually to prevent host controller halt*/
- printk("%s status 1 0x%08x [%s]\n",
- __func__,mci_readl(host, STATUS),mmc_hostname(host->mmc));
+ }else{
+ /*single block read/write, send stop cmd manually to prevent host controller halt*/
+ MMC_DBG_INFO_FUNC(host->mmc, "%s status 1 0x%08x [%s]\n",
+ __func__, mci_readl(host, STATUS), mmc_hostname(host->mmc));
+
mci_writel(host, CMDARG, 0);
- wmb();
- cmd_flags = SDMMC_CMD_STOP |SDMMC_CMD_RESP_CRC|SDMMC_CMD_RESP_EXP|MMC_STOP_TRANSMISSION;
- if(host->mmc->hold_reg_flag)
- cmd_flags |= SDMMC_CMD_USE_HOLD_REG;
- // mci_writel(host, CMD, SDMMC_CMD_USE_HOLD_REG |SDMMC_CMD_STOP |SDMMC_CMD_RESP_CRC|SDMMC_CMD_RESP_EXP| SDMMC_CMD_START|0x0c);
- mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
- wmb();
- unsigned long timeout = jiffies + msecs_to_jiffies(500);
- bool ret=0;
- while(ret=time_before(jiffies, timeout)){
- if(!(mci_readl(host, CMD)&SDMMC_CMD_START))
- break;
- }
- if(!ret)
- printk("%s EVENT_DATA_ERROR recovery failed!!! [%s]\n",
- __func__,mmc_hostname(host->mmc));
- }
+ wmb();
+ cmd_flags = SDMMC_CMD_STOP | SDMMC_CMD_RESP_CRC
+ | SDMMC_CMD_RESP_EXP | MMC_STOP_TRANSMISSION;
+
+ if(host->mmc->hold_reg_flag)
+ cmd_flags |= SDMMC_CMD_USE_HOLD_REG;
+
+ mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
+ wmb();
+ timeout = jiffies + msecs_to_jiffies(500);
+
+ while(ret){
+ ret = time_before(jiffies, timeout);
+ if(!(mci_readl(host, CMD) & SDMMC_CMD_START))
+ break;
+ }
+ if(false == ret)
+ MMC_DBG_ERR_FUNC(host->mmc,
+ "%s EVENT_DATA_ERROR recovery failed!!! [%s]\n",
+ __func__, mmc_hostname(host->mmc));
+ }
#else
send_stop_abort(host, data);
#endif
state = STATE_DATA_ERROR;
break;
}
- MMC_DBG_CMD_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: STATE_SENDING_DATA, wait for EVENT_XFER_COMPLETE.[%s]",\
+
+ MMC_DBG_CMD_FUNC(host->mmc,
+ "Pre-state[%d]-->NowState[%d]: STATE_SENDING_DATA, wait for EVENT_XFER_COMPLETE.[%s]",\
prev_state,state, mmc_hostname(host->mmc));
if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
&host->pending_events))
break;
- MMC_DBG_INFO_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: STATE_SENDING_DATA, wait for EVENT_DATA_COMPLETE. [%s]",\
+ MMC_DBG_INFO_FUNC(host->mmc,
+ "Pre-state[%d]-->NowState[%d]: STATE_SENDING_DATA, wait for EVENT_DATA_COMPLETE. [%s]",\
prev_state,state,mmc_hostname(host->mmc));
set_bit(EVENT_XFER_COMPLETE, &host->completed_events);
break;
dw_mci_deal_data_end(host, host->mrq);
- MMC_DBG_INFO_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: STATE_DATA_BUSY, after EVENT_DATA_COMPLETE. [%s]", \
+ del_timer_sync(&host->dto_timer); //delete the timer for INT_DTO
+ MMC_DBG_INFO_FUNC(host->mmc,
+ "Pre-state[%d]-->NowState[%d]: STATE_DATA_BUSY, after EVENT_DATA_COMPLETE. [%s]", \
prev_state,state,mmc_hostname(host->mmc));
host->data = NULL;
if (status & DW_MCI_DATA_ERROR_FLAGS) {
if((SDMMC_CTYPE_1BIT != slot->ctype)&&(MMC_SEND_EXT_CSD == host->mrq->cmd->opcode))
- MMC_DBG_ERR_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: DW_MCI_DATA_ERROR_FLAGS,datastatus=0x%x [%s]",\
+ MMC_DBG_ERR_FUNC(host->mmc,
+ "Pre-state[%d]-->NowState[%d]: DW_MCI_DATA_ERROR_FLAGS,datastatus=0x%x [%s]",\
prev_state,state, status, mmc_hostname(host->mmc));
if (status & SDMMC_INT_DRTO) {
} else if (status & SDMMC_INT_DCRC) {
data->error = -EILSEQ;
} else if (status & SDMMC_INT_EBE &&
- host->dir_status ==
- DW_MCI_SEND_STATUS) {
+ host->dir_status == DW_MCI_SEND_STATUS){
/*
* No data CRC status was returned.
* The number of bytes transferred will
dw_mci_request_end(host, host->mrq);
goto unlock;
}
- MMC_DBG_CMD_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: begin to stop . [%s]", \
- prev_state,state,mmc_hostname(host->mmc));
+ MMC_DBG_CMD_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: begin to stop . [%s]", \
+ prev_state,state,mmc_hostname(host->mmc));
if (host->mrq->sbc && !data->error) {
data->stop->error = 0;
- MMC_DBG_CMD_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: have stop and sbc, exit. [%s]", \
- prev_state,state,mmc_hostname(host->mmc));
+ MMC_DBG_CMD_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: have stop and sbc, exit. [%s]", \
+ prev_state,state,mmc_hostname(host->mmc));
dw_mci_request_end(host, host->mrq);
goto unlock;
}
#endif
/* fall through */
- MMC_DBG_CMD_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: begin to STATE_SENDING_STOP . [%s]", \
- prev_state,state,mmc_hostname(host->mmc));
+ MMC_DBG_CMD_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: begin to STATE_SENDING_STOP . [%s]", \
+ prev_state,state,mmc_hostname(host->mmc));
case STATE_SENDING_STOP:
- if (!test_and_clear_bit(EVENT_CMD_COMPLETE,
- &host->pending_events))
+ if (!test_and_clear_bit(EVENT_CMD_COMPLETE, &host->pending_events))
break;
- MMC_DBG_CMD_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: begin to send cmd12 . [%s]", \
- prev_state,state,mmc_hostname(host->mmc));
+
+ MMC_DBG_CMD_FUNC(host->mmc, "Pre-state[%d]-->NowState[%d]: begin to send cmd12 . [%s]", \
+ prev_state, state, mmc_hostname(host->mmc));
- /* CMD error in data command */
+ /* CMD error in data command */
if (host->mrq->cmd->error && host->mrq->data) {
dw_mci_fifo_reset(host);
}
host->cmd = NULL;
host->data = NULL;
- #if 1
- dw_mci_command_complete(host, host->mrq->stop);
- #else
+ #if 1
+ dw_mci_command_complete(host, host->mrq->stop);
+ #else
if (host->mrq->stop)
dw_mci_command_complete(host, host->mrq->stop);
else
host->cmd_status = 0;
- #endif
+ #endif
dw_mci_request_end(host, host->mrq);
goto unlock;
unsigned int remain, fcnt;
if(!host->mmc->bus_refs){
- printk("Note: %s host->mmc->bus_refs is 0!!!\n",__func__,host->mmc->bus_refs);
+ printk("Note: %s host->mmc->bus_refs is 0!!!\n", __func__);
goto host_put;
}
do {
unsigned int remain, fcnt;
if(!host->mmc->bus_refs){
- printk("Note: %s host->mmc->bus_refs is 0!!!\n",__func__,host->mmc->bus_refs);
+ printk("Note: %s host->mmc->bus_refs is 0!!!\n", __func__);
goto host_put;
}
static void dw_mci_cmd_interrupt(struct dw_mci *host, u32 status)
{
- if (!host->cmd_status)
+ u32 multi, unit = SZ_2M;
+
+ if (!host->cmd_status)
host->cmd_status = status;
- smp_wmb();
+ if (!host->cmd)
+ goto cmd_exit;
+
+ if ((MMC_STOP_TRANSMISSION != host->cmd->opcode)) {
+ multi = (mci_readl(host, BYTCNT) / unit) +
+ ((mci_readl(host, BYTCNT) % unit) ? 1 :0 ) +
+ ((host->cmd->retries > 2) ? 2 : host->cmd->retries);
+ /* Max limit time: 8s for dto */
+ mod_timer(&host->dto_timer, jiffies + msecs_to_jiffies(4000 * multi));
+ }
- set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
+cmd_exit:
+ smp_wmb();
+ set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
tasklet_schedule(&host->tasklet);
}
int i;
pending = mci_readl(host, MINTSTS); /* read-only mask reg */
- //if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD)
- // printk("%s pending: 0x%08x\n",__func__,pending);
+
/*
- * DTO fix - version 2.10a and below, and only if internal DMA
- * is configured.
- */
- if (host->quirks & DW_MCI_QUIRK_IDMAC_DTO) {
+ * DTO fix - version 2.10a and below, and only if internal DMA
+ * is configured.
+ */
+ if (host->quirks & DW_MCI_QUIRK_IDMAC_DTO) {
if (!pending &&
((mci_readl(host, STATUS) >> 17) & 0x1fff))
pending |= SDMMC_INT_DATA_OVER;
if (pending & SDMMC_INT_DATA_OVER) {
mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
+ del_timer(&host->dto_timer); /* delete the timer for INT_DTO */
MMC_DBG_CMD_FUNC(host->mmc, "SDMMC_INT_DATA_OVER, INT-pending=0x%x. [%s]",pending,mmc_hostname(host->mmc));
if (!host->data_status)
host->data_status = pending;
}
if (pending & SDMMC_INT_CMD_DONE) {
- MMC_DBG_CMD_FUNC(host->mmc, "SDMMC_INT_CMD_DONE, INT-pending=0x%x. [%s]",pending,mmc_hostname(host->mmc));
+ MMC_DBG_CMD_FUNC(host->mmc, "SDMMC_INT_CMD_DONE, CMD = 0x%x, INT-pending=0x%x. [%s]",mci_readl(host, CMD),pending,mmc_hostname(host->mmc));
mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE);
dw_mci_cmd_interrupt(host, pending);
}
if (pending & SDMMC_INT_CD) {
mci_writel(host, RINTSTS, SDMMC_INT_CD);
- rk_send_wakeup_key();//wake up system
+ MMC_DBG_INFO_FUNC(host->mmc, "SDMMC_INT_CD, INT-pending=0x%x. [%s]", pending, mmc_hostname(host->mmc));
+ wake_lock_timeout(&host->mmc->detect_wake_lock, 5 * HZ);
queue_work(host->card_workqueue, &host->card_work);
}
for (i = 0; i < host->num_slots; i++) {
struct dw_mci_slot *slot = host->slot[i];
- if (host->verid < DW_MMC_240A)
- sdio_int = SDMMC_INT_SDIO(i);
- else
- sdio_int = SDMMC_INT_SDIO(i + 8);
+ if (host->verid < DW_MMC_240A)
+ sdio_int = SDMMC_INT_SDIO(i);
+ else
+ sdio_int = SDMMC_INT_SDIO(i + 8);
if (pending & sdio_int) {
mci_writel(host, RINTSTS, sdio_int);
}
#ifdef CONFIG_MMC_DW_IDMAC
- /* Handle DMA interrupts */
- pending = mci_readl(host, IDSTS);
- if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
- mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI);
- mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
- host->dma_ops->complete(host);
- }
+ /* External DMA Soc platform NOT need to ack interrupt IDSTS */
+ if(!(cpu_is_rk3036() || cpu_is_rk312x())){
+ /* Handle DMA interrupts */
+ pending = mci_readl(host, IDSTS);
+ if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
+ mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI);
+ mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
+ host->dma_ops->complete((void *)host);
+ }
+ }
#endif
return IRQ_HANDLED;
struct mmc_host *mmc = slot->mmc;
struct mmc_request *mrq;
int present;
- u32 ctrl;
present = dw_mci_get_cd(mmc);
while (present != slot->last_detect_state) {
dev_dbg(&slot->mmc->class_dev, "card %s\n",
present ? "inserted" : "removed");
- MMC_DBG_BOOT_FUNC(mmc, " The card is %s. ===!!!!!!==[%s]\n",
+ MMC_DBG_BOOT_FUNC(mmc, " The card is %s. ===!!!!!!==[%s]\n",
present ? "inserted" : "removed.", mmc_hostname(mmc));
-
+
+ rk_send_wakeup_key();//wake up system
spin_lock_bh(&host->lock);
+ del_timer(&host->dto_timer); /* delete the timer for INT_DTO */
/* Card change detected */
slot->last_detect_state = present;
if (mrq->stop)
mrq->stop->error = -ENOMEDIUM;
- MMC_DBG_CMD_FUNC(host->mmc, "dw_mci_work--reqeuest done, cmd=%d [%s]",mrq->cmd->opcode, mmc_hostname(mmc));
+ MMC_DBG_CMD_FUNC(host->mmc, "dw_mci_work--reqeuest done, cmd=%d [%s]",
+ mrq->cmd->opcode, mmc_hostname(mmc));
spin_unlock(&host->lock);
mmc_request_done(slot->mmc, mrq);
/* Clear down the FIFO */
dw_mci_fifo_reset(host);
#ifdef CONFIG_MMC_DW_IDMAC
- dw_mci_idmac_reset(host);
+ if(!(cpu_is_rk3036() || cpu_is_rk312x()))
+ dw_mci_idmac_reset(host);
#endif
}
}
mmc_detect_change(slot->mmc,
- msecs_to_jiffies(host->pdata->detect_delay_ms));
+ msecs_to_jiffies(host->pdata->detect_delay_ms));
}
}
if (mmc_gpio_request_cd(mmc, gpio, 0))
dev_warn(dev, "gpio [%d] request failed\n", gpio);
}
+
+static irqreturn_t dw_mci_gpio_cd_irqt(int irq, void *dev_id)
+{
+ struct mmc_host *mmc = dev_id;
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+
+ #if 0
+ if (mmc->ops->card_event)
+ mmc->ops->card_event(mmc);
+
+ mmc_detect_change(mmc, msecs_to_jiffies(200));
+ #endif
+
+ queue_work(host->card_workqueue, &host->card_work);
+ return IRQ_HANDLED;
+}
+
+static void dw_mci_of_set_cd_gpio_irq(struct device *dev, u32 gpio,
+ struct mmc_host *mmc)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ int irq;
+ int ret;
+
+ /* Having a missing entry is valid; return silently */
+ if (!gpio_is_valid(gpio))
+ return;
+
+ irq = gpio_to_irq(gpio);
+ if (irq >= 0) {
+ ret = devm_request_threaded_irq(&mmc->class_dev, irq,
+ NULL, dw_mci_gpio_cd_irqt,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "dw_mci_cd", mmc);
+ if (ret < 0) {
+ irq = ret;
+ dev_err(host->dev, "Request cd-gpio %d interrupt error!\n", gpio);
+ } else{
+ /* enable wakeup event for gpio-cd in idle or deep suspend*/
+ enable_irq_wake(irq);
+ }
+ } else {
+ dev_err(host->dev, "Cannot convert gpio %d to irq!\n", gpio);
+ }
+}
+
+static void dw_mci_of_free_cd_gpio_irq(struct device *dev, u32 gpio,
+ struct mmc_host *mmc)
+{
+ if (!gpio_is_valid(gpio))
+ return;
+
+ if (gpio_to_irq(gpio) >= 0) {
+ devm_free_irq(&mmc->class_dev, gpio_to_irq(gpio), mmc);
+ devm_gpio_free(&mmc->class_dev, gpio);
+ }
+}
#else /* CONFIG_OF */
static int dw_mci_of_get_slot_quirks(struct device *dev, u8 slot)
{
mmc->f_min = DW_MCI_FREQ_MIN;
mmc->f_max = DW_MCI_FREQ_MAX;
- printk("%d..%s: fmin=%d, fmax=%d [%s]\n", __LINE__,__FUNCTION__,
- mmc->f_min, mmc->f_max, mmc_hostname(mmc));
+ printk("%d..%s: fmin=%d, fmax=%d [%s]\n", __LINE__, __FUNCTION__,
+ mmc->f_min, mmc->f_max, mmc_hostname(mmc));
} else {
mmc->f_min = freq[0];
mmc->f_max = freq[1];
- printk("%d..%s: fmin=%d, fmax=%d [%s]\n", __LINE__,__FUNCTION__,
- mmc->f_min, mmc->f_max, mmc_hostname(mmc));
+ printk("%d..%s: fmin=%d, fmax=%d [%s]\n", __LINE__, __FUNCTION__,
+ mmc->f_min, mmc->f_max, mmc_hostname(mmc));
}
-
- if(strstr("mmc0",mmc_hostname(mmc)))
- printk("Line%d..%s: The rk_sdmmc %s",__LINE__, __FUNCTION__,RK_SDMMC_DRIVER_VERSION);
+
+ printk("%s : Rockchip specific MHSC: %s\n", mmc_hostname(mmc), RK_SDMMC_DRIVER_VERSION);
if (of_find_property(host->dev->of_node, "supports-sd", NULL))
mmc->restrict_caps |= RESTRICT_CARD_TYPE_SD;
mmc->restrict_caps |= RESTRICT_CARD_TYPE_SDIO;
if (of_find_property(host->dev->of_node, "supports-emmc", NULL))
mmc->restrict_caps |= RESTRICT_CARD_TYPE_EMMC;
+ /* Fixup for tSD */
+ if (of_find_property(host->dev->of_node, "supports-tSD", NULL))
+ mmc->restrict_caps |= RESTRICT_CARD_TYPE_TSD;
+
+
+ /* We assume only low-level chip use gpio_cd */
+ if (cpu_is_rk312x() &&
+ soc_is_rk3126() &&
+ (host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD)) {
+ slot->cd_gpio = of_get_named_gpio(host->dev->of_node, "cd-gpios", 0);
+ if (gpio_is_valid(slot->cd_gpio)) {
+ /* Request gpio int for card detection */
+ dw_mci_of_set_cd_gpio_irq(host->dev, slot->cd_gpio,host->mmc);
+ } else {
+ slot->cd_gpio = -ENODEV;
+ dev_err(host->dev, "failed to get your cd-gpios!\n");
+ }
+ }
if (host->pdata->get_ocr)
mmc->ocr_avail = host->pdata->get_ocr(id);
if (drv_data && drv_data->hold_reg_flag)
mmc->hold_reg_flag |= drv_data->hold_reg_flag[ctrl_id];
- //set the compatibility of driver.
- mmc->caps |= MMC_CAP_UHS_SDR12|MMC_CAP_UHS_SDR25|MMC_CAP_UHS_SDR50|MMC_CAP_UHS_SDR104|MMC_CAP_ERASE;
+ /* set the compatibility of driver. */
+ mmc->caps |= MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | MMC_CAP_UHS_SDR50
+ | MMC_CAP_UHS_SDR104 | MMC_CAP_ERASE ;
if (host->pdata->caps2)
mmc->caps2 = host->pdata->caps2;
bus_width = 1;
switch (bus_width) {
- case 8:
- mmc->caps |= MMC_CAP_8_BIT_DATA;
- case 4:
- mmc->caps |= MMC_CAP_4_BIT_DATA;
+ case 8:
+ mmc->caps |= MMC_CAP_8_BIT_DATA;
+ case 4:
+ mmc->caps |= MMC_CAP_4_BIT_DATA;
}
+
if (of_find_property(host->dev->of_node, "cap-power-off-card", NULL))
- mmc->caps |= MMC_CAP_POWER_OFF_CARD;
+ mmc->caps |= MMC_CAP_POWER_OFF_CARD;
if (of_find_property(host->dev->of_node, "cap-sdio-irq", NULL))
mmc->caps |= MMC_CAP_SDIO_IRQ;
if (of_find_property(host->dev->of_node, "poll-hw-reset", NULL))
mmc->caps2 |= MMC_CAP2_FULL_PWR_CYCLE;
if (of_find_property(host->dev->of_node, "keep-power-in-suspend", NULL))
mmc->pm_caps |= MMC_PM_KEEP_POWER;
- if (of_find_property(host->dev->of_node, "ignore-pm-notify", NULL))
- mmc->pm_caps |= MMC_PM_IGNORE_PM_NOTIFY;
+ if (of_find_property(host->dev->of_node, "ignore-pm-notify", NULL))
+ mmc->pm_caps |= MMC_PM_IGNORE_PM_NOTIFY;
if (of_find_property(host->dev->of_node, "enable-sdio-wakeup", NULL))
mmc->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
- /*Assign pm_caps pass to pm_flags*/
+ /*Assign pm_caps pass to pm_flags*/
mmc->pm_flags = mmc->pm_caps;
if (host->pdata->blk_settings) {
mmc->max_blk_count = host->ring_size;
mmc->max_seg_size = 0x1000;
mmc->max_req_size = mmc->max_seg_size * mmc->max_blk_count;
+ if(cpu_is_rk3036() || cpu_is_rk312x()){
+ /* fixup for external dmac setting */
+ mmc->max_segs = 64;
+ mmc->max_blk_size = 65536; /* BLKSIZ is 16 bits */
+ mmc->max_blk_count = 65535;
+ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
+ mmc->max_seg_size = mmc->max_req_size;
+ }
#else
mmc->max_segs = 64;
mmc->max_blk_size = 65536; /* BLKSIZ is 16 bits */
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
#endif /* CONFIG_MMC_DW_IDMAC */
+
}
- //pwr_en
- slot->pwr_en_gpio = dw_mci_of_get_pwr_en_gpio(host->dev, slot->id);
+ /* pwr_en */
+ slot->pwr_en_gpio = dw_mci_of_get_pwr_en_gpio(host->dev, slot->id);
- if (!(mmc->restrict_caps & RESTRICT_CARD_TYPE_SD))//(gpio_is_valid(slot->pwr_en_gpio))
- {
- host->vmmc = NULL;
- }else{
-
- if(mmc->restrict_caps & RESTRICT_CARD_TYPE_SD)
+ if (!(mmc->restrict_caps & RESTRICT_CARD_TYPE_SD))
{
- host->vmmc = devm_regulator_get(mmc_dev(mmc), "vmmc");
- }
- else
- {
- host->vmmc = NULL;
- }
+ host->vmmc = NULL;
+ }else{
+
+ if(mmc->restrict_caps & RESTRICT_CARD_TYPE_SD)
+ host->vmmc = devm_regulator_get(mmc_dev(mmc), "vmmc");
+ else
+ host->vmmc = NULL;
- if (IS_ERR(host->vmmc)) {
- pr_info("%s: no vmmc regulator found\n", mmc_hostname(mmc));
- host->vmmc = NULL;
- } else {
- ret = regulator_enable(host->vmmc);
- if (ret) {
- dev_err(host->dev,
- "failed to enable regulator: %d\n", ret);
- goto err_setup_bus;
- }
- }
- }
+ if (IS_ERR(host->vmmc)) {
+ pr_info("%s: no vmmc regulator found\n", mmc_hostname(mmc));
+ host->vmmc = NULL;
+ }else{
+ ret = regulator_enable(host->vmmc);
+ if (ret) {
+ dev_err(host->dev,
+ "failed to enable regulator: %d\n", ret);
+ host->vmmc = NULL;
+ goto err_setup_bus;
+ }
+ }
+ }
- slot->wp_gpio = dw_mci_of_get_wp_gpio(host->dev, slot->id);
+ slot->wp_gpio = dw_mci_of_get_wp_gpio(host->dev, slot->id);
- if (mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO)
- clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+ if (mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO)
+ clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
- ret = mmc_add_host(mmc);
- if (ret)
- goto err_setup_bus;
-
- /* Pinctrl set default iomux state to fucntion port.
- * Fixme: DON'T TOUCH EMMC SETTING!
- */
- if(!(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_EMMC))
- {
- host->pinctrl = devm_pinctrl_get(host->dev);
- if(IS_ERR(host->pinctrl))
- printk("%s: Warning : No pinctrl used!\n",mmc_hostname(host->mmc));
- else
+ ret = mmc_add_host(mmc);
+ if (ret)
+ goto err_setup_bus;
+
+ /* Pinctrl set default iomux state to fucntion port.
+ * Fixme: DON'T TOUCH EMMC SETTING!
+ */
+ if(!(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_EMMC))
{
- host->pins_idle= pinctrl_lookup_state(host->pinctrl,PINCTRL_STATE_IDLE);
- if(IS_ERR(host->pins_default))
- printk("%s: Warning : No IDLE pinctrl matched!\n", mmc_hostname(host->mmc));
- else
- {
- if(pinctrl_select_state(host->pinctrl, host->pins_idle) < 0)
- printk("%s: Warning : Idle pinctrl setting failed!\n", mmc_hostname(host->mmc));
- }
+ host->pinctrl = devm_pinctrl_get(host->dev);
+ if(IS_ERR(host->pinctrl)){
+ printk("%s: Warning : No pinctrl used!\n",mmc_hostname(host->mmc));
+ }else{
+ host->pins_idle= pinctrl_lookup_state(host->pinctrl,PINCTRL_STATE_IDLE);
+ if(IS_ERR(host->pins_default)){
+ printk("%s: Warning : No IDLE pinctrl matched!\n", mmc_hostname(host->mmc));
+ }
+ else
+ {
+ if(pinctrl_select_state(host->pinctrl, host->pins_idle) < 0)
+ printk("%s: Warning : Idle pinctrl setting failed!\n", mmc_hostname(host->mmc));
+ }
- host->pins_default = pinctrl_lookup_state(host->pinctrl,PINCTRL_STATE_DEFAULT);
- if(IS_ERR(host->pins_default))
- printk("%s: Warning : No default pinctrl matched!\n", mmc_hostname(host->mmc));
- else
- {
- if(pinctrl_select_state(host->pinctrl, host->pins_default) < 0)
- printk("%s: Warning : Default pinctrl setting failed!\n", mmc_hostname(host->mmc));
- }
- }
- }
+ host->pins_default = pinctrl_lookup_state(host->pinctrl,PINCTRL_STATE_DEFAULT);
+ if(IS_ERR(host->pins_default)){
+ printk("%s: Warning : No default pinctrl matched!\n", mmc_hostname(host->mmc));
+ }
+ else
+ {
+ if(pinctrl_select_state(host->pinctrl, host->pins_default) < 0)
+ printk("%s: Warning : Default pinctrl setting failed!\n", mmc_hostname(host->mmc));
+ }
+ }
+ }
#if defined(CONFIG_DEBUG_FS)
return 0;
err_setup_bus:
+ if (gpio_is_valid(slot->cd_gpio))
+ dw_mci_of_free_cd_gpio_irq(host->dev, slot->cd_gpio,host->mmc);
mmc_free_host(mmc);
return -EINVAL;
}
}
/* Determine which DMA interface to use */
-#ifdef CONFIG_MMC_DW_IDMAC
- host->dma_ops = &dw_mci_idmac_ops;
- dev_info(host->dev, "Using internal DMA controller.\n");
+#if defined(CONFIG_MMC_DW_IDMAC)
+ if(cpu_is_rk3036() || cpu_is_rk312x()){
+ host->dma_ops = &dw_mci_edmac_ops;
+ dev_info(host->dev, "Using external DMA controller.\n");
+ }else{
+ host->dma_ops = &dw_mci_idmac_ops;
+ dev_info(host->dev, "Using internal DMA controller.\n");
+ }
#endif
if (!host->dma_ops)
do {
ctrl = mci_readl(host, CTRL);
if (!(ctrl & reset))
- return true;
+ return true;
} while (time_before(jiffies, timeout));
dev_err(host->dev,
"Timeout resetting block (ctrl reset %#x)\n",
ctrl & reset);
-
+
return false;
}
}
#ifdef CONFIG_OF
+/*
static struct dw_mci_of_quirks {
char *quirk;
int id;
.id = DW_MCI_QUIRK_BROKEN_CARD_DETECTION,
},
};
-
+*/
static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
{
struct dw_mci_board *pdata;
struct device *dev = host->dev;
struct device_node *np = dev->of_node;
const struct dw_mci_drv_data *drv_data = host->drv_data;
- int idx, ret;
+ int ret;
u32 clock_frequency;
pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
}
#endif /* CONFIG_OF */
+static void dw_mci_dealwith_timeout(struct dw_mci *host)
+{
+ u32 ret, i, regs;
+
+ switch(host->state){
+ case STATE_IDLE:
+ break;
+ case STATE_SENDING_DATA:
+ case STATE_DATA_BUSY:
+ host->data_status |= (SDMMC_INT_DCRC|SDMMC_INT_EBE);
+ mci_writel(host, RINTSTS, SDMMC_INT_DRTO); // clear interrupt
+ set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
+ host->state = STATE_DATA_BUSY;
+ if (!dw_mci_ctrl_all_reset(host)) {
+ ret = -ENODEV;
+ return ;
+ }
+
+ /* NO requirement to reclaim slave chn using external dmac */
+ #ifdef CONFIG_MMC_DW_IDMAC
+ if(!(cpu_is_rk3036() || cpu_is_rk312x()))
+ if (host->use_dma && host->dma_ops->init)
+ host->dma_ops->init(host);
+ #endif
+
+ /*
+ * Restore the initial value at FIFOTH register
+ * And Invalidate the prev_blksz with zero
+ */
+ mci_writel(host, FIFOTH, host->fifoth_val);
+ host->prev_blksz = 0;
+ mci_writel(host, TMOUT, 0xFFFFFFFF);
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+ regs = SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER | SDMMC_INT_TXDR
+ | SDMMC_INT_RXDR | SDMMC_INT_VSI | DW_MCI_ERROR_FLAGS;
+ if(!(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO))
+ regs |= SDMMC_INT_CD;
+ mci_writel(host, INTMASK, regs);
+ mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
+ for (i = 0; i < host->num_slots; i++) {
+ struct dw_mci_slot *slot = host->slot[i];
+ if (!slot)
+ continue;
+ if (slot->mmc->pm_flags & MMC_PM_KEEP_POWER) {
+ dw_mci_set_ios(slot->mmc, &slot->mmc->ios);
+ dw_mci_setup_bus(slot, true);
+ }
+ }
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+ tasklet_schedule(&host->tasklet);
+ break;
+ default:
+ break;
+ }
+}
+static void dw_mci_dto_timeout(unsigned long host_data)
+{
+ struct dw_mci *host = (struct dw_mci *) host_data;
+
+ disable_irq(host->irq);
+
+ host->data_status = SDMMC_INT_EBE;
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+ dw_mci_dealwith_timeout(host);
+
+ enable_irq(host->irq);
+}
int dw_mci_probe(struct dw_mci *host)
{
const struct dw_mci_drv_data *drv_data = host->drv_data;
else
host->data_offset = DATA_240A_OFFSET;
- //hclk enable
- host->hclk_mmc= devm_clk_get(host->dev, "hclk_mmc");
- if (IS_ERR(host->hclk_mmc)) {
- dev_err(host->dev, "failed to get hclk_mmc\n");
- ret = PTR_ERR(host->hclk_mmc);
- goto err_hclk_mmc;
- }
- clk_prepare_enable(host->hclk_mmc);
-
- //mmc clk enable
- host->clk_mmc = devm_clk_get(host->dev, "clk_mmc");
- if (IS_ERR(host->clk_mmc)) {
- dev_err(host->dev, "failed to get clk mmc_per\n");
- ret = PTR_ERR(host->clk_mmc);
- goto err_clk_mmc;
- }
+ //hclk enable
+ host->hclk_mmc= devm_clk_get(host->dev, "hclk_mmc");
+ if (IS_ERR(host->hclk_mmc)) {
+ dev_err(host->dev, "failed to get hclk_mmc\n");
+ ret = PTR_ERR(host->hclk_mmc);
+ goto err_hclk_mmc;
+ }
+
+ clk_prepare_enable(host->hclk_mmc);
+
+ //mmc clk enable
+ host->clk_mmc = devm_clk_get(host->dev, "clk_mmc");
+ if (IS_ERR(host->clk_mmc)) {
+ dev_err(host->dev, "failed to get clk mmc_per\n");
+ ret = PTR_ERR(host->clk_mmc);
+ goto err_clk_mmc;
+ }
- if (host->verid < DW_MMC_240A)
- host->bus_hz = host->pdata->bus_hz;
- else
- host->bus_hz = host->pdata->bus_hz*2;// *2 due to fix divider 2 in controller.
- if (!host->bus_hz) {
- dev_err(host->dev,"Platform data must supply bus speed\n");
- ret = -ENODEV;
- goto err_clk_mmc;
- }
+ host->bus_hz = host->pdata->bus_hz;
+ if (!host->bus_hz) {
+ dev_err(host->dev,"Platform data must supply bus speed\n");
+ ret = -ENODEV;
+ goto err_clk_mmc;
+ }
- ret = clk_set_rate(host->clk_mmc, host->bus_hz);
+ if (host->verid < DW_MMC_240A)
+ ret = clk_set_rate(host->clk_mmc, host->bus_hz);
+ else
+ //rockchip: fix divider 2 in clksum before controlller
+ ret = clk_set_rate(host->clk_mmc, host->bus_hz * 2);
+
if(ret < 0) {
dev_err(host->dev, "failed to set clk mmc\n");
goto err_clk_mmc;
}
- clk_prepare_enable(host->clk_mmc);
+ clk_prepare_enable(host->clk_mmc);
if (drv_data && drv_data->setup_clock) {
ret = drv_data->setup_clock(host);
}
}
- host->quirks = host->pdata->quirks;
- host->irq_state = true;
- host->set_speed = 0;
- host->set_div = 0;
+ host->quirks = host->pdata->quirks;
+ host->irq_state = true;
+ host->set_speed = 0;
+ host->set_div = 0;
+ host->svi_flags = 0;
spin_lock_init(&host->lock);
INIT_LIST_HEAD(&host->queue);
else
host->num_slots = ((mci_readl(host, HCON) >> 1) & 0x1F) + 1;
+ setup_timer(&host->dto_timer, dw_mci_dto_timeout, (unsigned long)host);
/* We need at least one slot to succeed */
for (i = 0; i < host->num_slots; i++) {
ret = dw_mci_init_slot(host, i);
void dw_mci_remove(struct dw_mci *host)
{
+ struct mmc_host *mmc = host->mmc;
+ struct dw_mci_slot *slot = mmc_priv(mmc);
int i;
- mci_writel(host, RINTSTS, 0xFFFFFFFF);
- mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
+ del_timer_sync(&host->dto_timer);
- for (i = 0; i < host->num_slots; i++) {
- dev_dbg(host->dev, "remove slot %d\n", i);
- if (host->slot[i])
- dw_mci_cleanup_slot(host->slot[i], i);
- }
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+ mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
- /* disable clock to CIU */
- mci_writel(host, CLKENA, 0);
- mci_writel(host, CLKSRC, 0);
+ for(i = 0; i < host->num_slots; i++){
+ dev_dbg(host->dev, "remove slot %d\n", i);
+ if(host->slot[i])
+ dw_mci_cleanup_slot(host->slot[i], i);
+ }
- destroy_workqueue(host->card_workqueue);
+ /* disable clock to CIU */
+ mci_writel(host, CLKENA, 0);
+ mci_writel(host, CLKSRC, 0);
- if (host->use_dma && host->dma_ops->exit)
- host->dma_ops->exit(host);
+ destroy_workqueue(host->card_workqueue);
- if (host->vmmc){
- regulator_disable(host->vmmc);
- regulator_put(host->vmmc);
- }
-
- if (!IS_ERR(host->clk_mmc))
- clk_disable_unprepare(host->clk_mmc);
+ if(host->use_dma && host->dma_ops->exit)
+ host->dma_ops->exit(host);
- if (!IS_ERR(host->hclk_mmc))
- clk_disable_unprepare(host->hclk_mmc);
+ if (gpio_is_valid(slot->cd_gpio))
+ dw_mci_of_free_cd_gpio_irq(host->dev, slot->cd_gpio, host->mmc);
+
+ if(host->vmmc){
+ regulator_disable(host->vmmc);
+ regulator_put(host->vmmc);
+ }
+ if(!IS_ERR(host->clk_mmc))
+ clk_disable_unprepare(host->clk_mmc);
+
+ if(!IS_ERR(host->hclk_mmc))
+ clk_disable_unprepare(host->hclk_mmc);
}
EXPORT_SYMBOL(dw_mci_remove);
*/
int dw_mci_suspend(struct dw_mci *host)
{
-
- if (host->vmmc)
- regulator_disable(host->vmmc);
-
- /*only for sdmmc controller*/
- if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD) {
- disable_irq(host->irq);
-
- if(pinctrl_select_state(host->pinctrl, host->pins_idle) < 0)
- printk("%s: Warning : Idle pinctrl setting failed!\n", mmc_hostname(host->mmc));
- dw_mci_of_get_cd_gpio(host->dev,0,host->mmc);
-
- enable_irq_wake(host->mmc->slot.cd_irq);
- }
- return 0;
+ if(host->vmmc)
+ regulator_disable(host->vmmc);
+
+ if(host->use_dma && host->dma_ops->exit)
+ host->dma_ops->exit(host);
+
+ /*only for sdmmc controller*/
+ if (host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD) {
+ host->mmc->rescan_disable = 1;
+ if (cancel_delayed_work_sync(&host->mmc->detect))
+ wake_unlock(&host->mmc->detect_wake_lock);
+
+ disable_irq(host->irq);
+ if (pinctrl_select_state(host->pinctrl, host->pins_idle) < 0)
+ MMC_DBG_ERR_FUNC(host->mmc, "Idle pinctrl setting failed! [%s]",
+ mmc_hostname(host->mmc));
+
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+ mci_writel(host, INTMASK, 0x00);
+ mci_writel(host, CTRL, 0x00);
+
+ /* Soc rk3126 already in gpio_cd mode */
+ if (!(cpu_is_rk312x() && soc_is_rk3126())) {
+ dw_mci_of_get_cd_gpio(host->dev, 0, host->mmc);
+ enable_irq_wake(host->mmc->slot.cd_irq);
+ }
+ }
+ return 0;
}
EXPORT_SYMBOL(dw_mci_suspend);
int dw_mci_resume(struct dw_mci *host)
{
- int i, ret;
+ int i, ret, retry_cnt = 0;
u32 regs;
+ struct dw_mci_slot *slot;
+
+ if (host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SDIO){
+ slot = mmc_priv(host->mmc);
- if (host->vmmc) {
+ if(!test_bit(DW_MMC_CARD_PRESENT, &slot->flags))
+ return 0;
+ }
+ /*only for sdmmc controller*/
+ if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD) {
+ /* Soc rk3126 already in gpio_cd mode */
+ if (!(cpu_is_rk312x() && soc_is_rk3126())) {
+ disable_irq_wake(host->mmc->slot.cd_irq);
+ mmc_gpio_free_cd(host->mmc);
+ }
+ if(pinctrl_select_state(host->pinctrl, host->pins_default) < 0)
+ MMC_DBG_ERR_FUNC(host->mmc, "Default pinctrl setting failed! [%s]",
+ mmc_hostname(host->mmc));
+ host->mmc->rescan_disable = 0;
+ /* Disable jtag*/
+ if(cpu_is_rk3288())
+ grf_writel(((1 << 12) << 16) | (0 << 12), RK3288_GRF_SOC_CON0);
+ else if(cpu_is_rk3036())
+ grf_writel(((1 << 11) << 16) | (0 << 11), RK3036_GRF_SOC_CON0);
+ else if(cpu_is_rk312x())
+ /* RK3036_GRF_SOC_CON0 is compatible with rk312x, tmp setting */
+ grf_writel(((1 << 8) << 16) | (0 << 8), RK3036_GRF_SOC_CON0);
+ }
+ if(host->vmmc){
ret = regulator_enable(host->vmmc);
- if (ret) {
+ if (ret){
dev_err(host->dev,
"failed to enable regulator: %d\n", ret);
return ret;
}
}
-
- if (!dw_mci_ctrl_all_reset(host)) {
+
+ if(!dw_mci_ctrl_all_reset(host)){
ret = -ENODEV;
return ret;
}
- if (host->use_dma && host->dma_ops->init)
+ if(host->use_dma && host->dma_ops->init)
host->dma_ops->init(host);
/*
regs |= SDMMC_INT_CD;
mci_writel(host, INTMASK, regs);
mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
+ /*only for sdmmc controller*/
+ if((host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD)&& (!retry_cnt)){
+ enable_irq(host->irq);
+ }
- for (i = 0; i < host->num_slots; i++) {
+ for(i = 0; i < host->num_slots; i++){
struct dw_mci_slot *slot = host->slot[i];
- if (!slot)
+ if(!slot)
continue;
- if (slot->mmc->pm_flags & MMC_PM_KEEP_POWER) {
+ if(slot->mmc->pm_flags & MMC_PM_KEEP_POWER){
dw_mci_set_ios(slot->mmc, &slot->mmc->ios);
dw_mci_setup_bus(slot, true);
}
}
-
- /*only for sdmmc controller*/
- if(host->mmc->restrict_caps & RESTRICT_CARD_TYPE_SD) {
- disable_irq_wake(host->mmc->slot.cd_irq);
- mmc_gpio_free_cd(host->mmc);
- if(pinctrl_select_state(host->pinctrl, host->pins_default) < 0)
- printk("%s: Warning : Default pinctrl setting failed!\n", mmc_hostname(host->mmc));
-
- enable_irq(host->irq);
-
- }
-
return 0;
}
EXPORT_SYMBOL(dw_mci_resume);
module_init(dw_mci_init);
module_exit(dw_mci_exit);
-MODULE_DESCRIPTION("DW Multimedia Card Interface driver");
-
+MODULE_DESCRIPTION("Rockchip specific DW Multimedia Card Interface driver");
MODULE_AUTHOR("NXP Semiconductor VietNam");
MODULE_AUTHOR("Imagination Technologies Ltd");
+MODULE_AUTHOR("Shawn Lin <lintao@rock-chips.com>");
MODULE_AUTHOR("Rockchip Electronics£¬Bangwang Xie < xbw@rock-chips.com> ");
-
MODULE_LICENSE("GPL v2");