intel_range_t dot, vco, n, m, m1, m2, p, p1;
intel_p2_t p2;
bool (* find_pll)(const intel_limit_t *, struct drm_crtc *,
- int, int, intel_clock_t *);
+ int, int, intel_clock_t *, intel_clock_t *);
};
/* FDI */
static bool
intel_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
- int target, int refclk, intel_clock_t *best_clock);
+ int target, int refclk, intel_clock_t *match_clock,
+ intel_clock_t *best_clock);
static bool
intel_g4x_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
- int target, int refclk, intel_clock_t *best_clock);
+ int target, int refclk, intel_clock_t *match_clock,
+ intel_clock_t *best_clock);
static bool
intel_find_pll_g4x_dp(const intel_limit_t *, struct drm_crtc *crtc,
- int target, int refclk, intel_clock_t *best_clock);
+ int target, int refclk, intel_clock_t *match_clock,
+ intel_clock_t *best_clock);
static bool
intel_find_pll_ironlake_dp(const intel_limit_t *, struct drm_crtc *crtc,
- int target, int refclk, intel_clock_t *best_clock);
+ int target, int refclk, intel_clock_t *match_clock,
+ intel_clock_t *best_clock);
static inline u32 /* units of 100MHz */
intel_fdi_link_freq(struct drm_device *dev)
.find_pll = intel_find_pll_ironlake_dp,
};
+u32 intel_dpio_read(struct drm_i915_private *dev_priv, int reg)
+{
+ unsigned long flags;
+ u32 val = 0;
+
+ spin_lock_irqsave(&dev_priv->dpio_lock, flags);
+ if (wait_for_atomic_us((I915_READ(DPIO_PKT) & DPIO_BUSY) == 0, 100)) {
+ DRM_ERROR("DPIO idle wait timed out\n");
+ goto out_unlock;
+ }
+
+ I915_WRITE(DPIO_REG, reg);
+ I915_WRITE(DPIO_PKT, DPIO_RID | DPIO_OP_READ | DPIO_PORTID |
+ DPIO_BYTE);
+ if (wait_for_atomic_us((I915_READ(DPIO_PKT) & DPIO_BUSY) == 0, 100)) {
+ DRM_ERROR("DPIO read wait timed out\n");
+ goto out_unlock;
+ }
+ val = I915_READ(DPIO_DATA);
+
+out_unlock:
+ spin_unlock_irqrestore(&dev_priv->dpio_lock, flags);
+ return val;
+}
+
+static void intel_dpio_write(struct drm_i915_private *dev_priv, int reg,
+ u32 val)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&dev_priv->dpio_lock, flags);
+ if (wait_for_atomic_us((I915_READ(DPIO_PKT) & DPIO_BUSY) == 0, 100)) {
+ DRM_ERROR("DPIO idle wait timed out\n");
+ goto out_unlock;
+ }
+
+ I915_WRITE(DPIO_DATA, val);
+ I915_WRITE(DPIO_REG, reg);
+ I915_WRITE(DPIO_PKT, DPIO_RID | DPIO_OP_WRITE | DPIO_PORTID |
+ DPIO_BYTE);
+ if (wait_for_atomic_us((I915_READ(DPIO_PKT) & DPIO_BUSY) == 0, 100))
+ DRM_ERROR("DPIO write wait timed out\n");
+
+out_unlock:
+ spin_unlock_irqrestore(&dev_priv->dpio_lock, flags);
+}
+
+static void vlv_init_dpio(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+
+ /* Reset the DPIO config */
+ I915_WRITE(DPIO_CTL, 0);
+ POSTING_READ(DPIO_CTL);
+ I915_WRITE(DPIO_CTL, 1);
+ POSTING_READ(DPIO_CTL);
+}
+
+static bool is_dual_link_lvds(struct drm_i915_private *dev_priv,
+ unsigned int reg)
+{
+ unsigned int val;
+
+ /* use the module option value if specified */
+ if (i915_lvds_channel_mode > 0)
+ return i915_lvds_channel_mode == 2;
+
+ if (dev_priv->lvds_val)
+ val = dev_priv->lvds_val;
+ else {
+ /* BIOS should set the proper LVDS register value at boot, but
+ * in reality, it doesn't set the value when the lid is closed;
+ * we need to check "the value to be set" in VBT when LVDS
+ * register is uninitialized.
+ */
+ val = I915_READ(reg);
+ if (!(val & ~LVDS_DETECTED))
+ val = dev_priv->bios_lvds_val;
+ dev_priv->lvds_val = val;
+ }
+ return (val & LVDS_CLKB_POWER_MASK) == LVDS_CLKB_POWER_UP;
+}
+
static const intel_limit_t *intel_ironlake_limit(struct drm_crtc *crtc,
int refclk)
{
const intel_limit_t *limit;
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
- if ((I915_READ(PCH_LVDS) & LVDS_CLKB_POWER_MASK) ==
- LVDS_CLKB_POWER_UP) {
+ if (is_dual_link_lvds(dev_priv, PCH_LVDS)) {
/* LVDS dual channel */
if (refclk == 100000)
limit = &intel_limits_ironlake_dual_lvds_100m;
const intel_limit_t *limit;
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
- if ((I915_READ(LVDS) & LVDS_CLKB_POWER_MASK) ==
- LVDS_CLKB_POWER_UP)
+ if (is_dual_link_lvds(dev_priv, LVDS))
/* LVDS with dual channel */
limit = &intel_limits_g4x_dual_channel_lvds;
else
static bool
intel_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
- int target, int refclk, intel_clock_t *best_clock)
+ int target, int refclk, intel_clock_t *match_clock,
+ intel_clock_t *best_clock)
{
struct drm_device *dev = crtc->dev;
* reliably set up different single/dual channel state, if we
* even can.
*/
- if ((I915_READ(LVDS) & LVDS_CLKB_POWER_MASK) ==
- LVDS_CLKB_POWER_UP)
+ if (is_dual_link_lvds(dev_priv, LVDS))
clock.p2 = limit->p2.p2_fast;
else
clock.p2 = limit->p2.p2_slow;
if (!intel_PLL_is_valid(dev, limit,
&clock))
continue;
+ if (match_clock &&
+ clock.p != match_clock->p)
+ continue;
this_err = abs(clock.dot - target);
if (this_err < err) {
static bool
intel_g4x_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
- int target, int refclk, intel_clock_t *best_clock)
+ int target, int refclk, intel_clock_t *match_clock,
+ intel_clock_t *best_clock)
{
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
if (!intel_PLL_is_valid(dev, limit,
&clock))
continue;
+ if (match_clock &&
+ clock.p != match_clock->p)
+ continue;
this_err = abs(clock.dot - target);
if (this_err < err_most) {
static bool
intel_find_pll_ironlake_dp(const intel_limit_t *limit, struct drm_crtc *crtc,
- int target, int refclk, intel_clock_t *best_clock)
+ int target, int refclk, intel_clock_t *match_clock,
+ intel_clock_t *best_clock)
{
struct drm_device *dev = crtc->dev;
intel_clock_t clock;
/* DisplayPort has only two frequencies, 162MHz and 270MHz */
static bool
intel_find_pll_g4x_dp(const intel_limit_t *limit, struct drm_crtc *crtc,
- int target, int refclk, intel_clock_t *best_clock)
+ int target, int refclk, intel_clock_t *match_clock,
+ intel_clock_t *best_clock)
{
intel_clock_t clock;
if (target < 200000) {
u32 val;
bool cur_state;
+ /* if we need the pipe A quirk it must be always on */
+ if (pipe == PIPE_A && dev_priv->quirks & QUIRK_PIPEA_FORCE)
+ state = true;
+
reg = PIPECONF(pipe);
val = I915_READ(reg);
cur_state = !!(val & PIPECONF_ENABLE);
pipe_name(pipe), state_string(state), state_string(cur_state));
}
-static void assert_plane_enabled(struct drm_i915_private *dev_priv,
- enum plane plane)
+static void assert_plane(struct drm_i915_private *dev_priv,
+ enum plane plane, bool state)
{
int reg;
u32 val;
+ bool cur_state;
reg = DSPCNTR(plane);
val = I915_READ(reg);
- WARN(!(val & DISPLAY_PLANE_ENABLE),
- "plane %c assertion failure, should be active but is disabled\n",
- plane_name(plane));
+ cur_state = !!(val & DISPLAY_PLANE_ENABLE);
+ WARN(cur_state != state,
+ "plane %c assertion failure (expected %s, current %s)\n",
+ plane_name(plane), state_string(state), state_string(cur_state));
}
+#define assert_plane_enabled(d, p) assert_plane(d, p, true)
+#define assert_plane_disabled(d, p) assert_plane(d, p, false)
+
static void assert_planes_disabled(struct drm_i915_private *dev_priv,
enum pipe pipe)
{
int cur_pipe;
/* Planes are fixed to pipes on ILK+ */
- if (HAS_PCH_SPLIT(dev_priv->dev))
+ if (HAS_PCH_SPLIT(dev_priv->dev)) {
+ reg = DSPCNTR(pipe);
+ val = I915_READ(reg);
+ WARN((val & DISPLAY_PLANE_ENABLE),
+ "plane %c assertion failure, should be disabled but not\n",
+ plane_name(pipe));
return;
+ }
/* Need to check both planes against the pipe */
for (i = 0; i < 2; i++) {
{
u32 val = I915_READ(reg);
WARN(hdmi_pipe_enabled(dev_priv, val, pipe),
- "PCH DP (0x%08x) enabled on transcoder %c, should be disabled\n",
+ "PCH HDMI (0x%08x) enabled on transcoder %c, should be disabled\n",
reg, pipe_name(pipe));
}
enum pipe pipe)
{
int reg;
- u32 val;
+ u32 val, pipeconf_val;
+ struct drm_crtc *crtc = dev_priv->pipe_to_crtc_mapping[pipe];
/* PCH only available on ILK+ */
BUG_ON(dev_priv->info->gen < 5);
reg = TRANSCONF(pipe);
val = I915_READ(reg);
+ pipeconf_val = I915_READ(PIPECONF(pipe));
if (HAS_PCH_IBX(dev_priv->dev)) {
/*
* that in pipeconf reg.
*/
val &= ~PIPE_BPC_MASK;
- val |= I915_READ(PIPECONF(pipe)) & PIPE_BPC_MASK;
+ val |= pipeconf_val & PIPE_BPC_MASK;
}
+
+ val &= ~TRANS_INTERLACE_MASK;
+ if ((pipeconf_val & PIPECONF_INTERLACE_MASK) == PIPECONF_INTERLACED_ILK)
+ if (HAS_PCH_IBX(dev_priv->dev) &&
+ intel_pipe_has_type(crtc, INTEL_OUTPUT_SDVO))
+ val |= TRANS_LEGACY_INTERLACED_ILK;
+ else
+ val |= TRANS_INTERLACED;
+ else
+ val |= TRANS_PROGRESSIVE;
+
I915_WRITE(reg, val | TRANS_ENABLE);
if (wait_for(I915_READ(reg) & TRANS_STATE_ENABLE, 100))
DRM_ERROR("failed to enable transcoder %d\n", pipe);
ret = i915_gem_object_get_fence(obj, pipelined);
if (ret)
goto err_unpin;
+
+ i915_gem_object_pin_fence(obj);
}
dev_priv->mm.interruptible = true;
return ret;
}
+void intel_unpin_fb_obj(struct drm_i915_gem_object *obj)
+{
+ i915_gem_object_unpin_fence(obj);
+ i915_gem_object_unpin(obj);
+}
+
static int i9xx_update_plane(struct drm_crtc *crtc, struct drm_framebuffer *fb,
int x, int y)
{
ret = intel_pipe_set_base_atomic(crtc, crtc->fb, x, y,
LEAVE_ATOMIC_MODE_SET);
if (ret) {
- i915_gem_object_unpin(to_intel_framebuffer(crtc->fb)->obj);
+ intel_unpin_fb_obj(to_intel_framebuffer(crtc->fb)->obj);
mutex_unlock(&dev->struct_mutex);
DRM_ERROR("failed to update base address\n");
return ret;
if (old_fb) {
intel_wait_for_vblank(dev, intel_crtc->pipe);
- i915_gem_object_unpin(to_intel_framebuffer(old_fb)->obj);
+ intel_unpin_fb_obj(to_intel_framebuffer(old_fb)->obj);
}
mutex_unlock(&dev->struct_mutex);
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
- u32 reg, temp, i;
+ u32 reg, temp, i, retry;
/* Train 1: umask FDI RX Interrupt symbol_lock and bit_lock bit
for train result */
POSTING_READ(reg);
udelay(500);
- reg = FDI_RX_IIR(pipe);
- temp = I915_READ(reg);
- DRM_DEBUG_KMS("FDI_RX_IIR 0x%x\n", temp);
-
- if (temp & FDI_RX_BIT_LOCK) {
- I915_WRITE(reg, temp | FDI_RX_BIT_LOCK);
- DRM_DEBUG_KMS("FDI train 1 done.\n");
- break;
+ for (retry = 0; retry < 5; retry++) {
+ reg = FDI_RX_IIR(pipe);
+ temp = I915_READ(reg);
+ DRM_DEBUG_KMS("FDI_RX_IIR 0x%x\n", temp);
+ if (temp & FDI_RX_BIT_LOCK) {
+ I915_WRITE(reg, temp | FDI_RX_BIT_LOCK);
+ DRM_DEBUG_KMS("FDI train 1 done.\n");
+ break;
+ }
+ udelay(50);
}
+ if (retry < 5)
+ break;
}
if (i == 4)
DRM_ERROR("FDI train 1 fail!\n");
POSTING_READ(reg);
udelay(500);
- reg = FDI_RX_IIR(pipe);
- temp = I915_READ(reg);
- DRM_DEBUG_KMS("FDI_RX_IIR 0x%x\n", temp);
-
- if (temp & FDI_RX_SYMBOL_LOCK) {
- I915_WRITE(reg, temp | FDI_RX_SYMBOL_LOCK);
- DRM_DEBUG_KMS("FDI train 2 done.\n");
- break;
+ for (retry = 0; retry < 5; retry++) {
+ reg = FDI_RX_IIR(pipe);
+ temp = I915_READ(reg);
+ DRM_DEBUG_KMS("FDI_RX_IIR 0x%x\n", temp);
+ if (temp & FDI_RX_SYMBOL_LOCK) {
+ I915_WRITE(reg, temp | FDI_RX_SYMBOL_LOCK);
+ DRM_DEBUG_KMS("FDI train 2 done.\n");
+ break;
+ }
+ udelay(50);
}
+ if (retry < 5)
+ break;
}
if (i == 4)
DRM_ERROR("FDI train 2 fail!\n");
I915_WRITE(TRANS_VTOTAL(pipe), I915_READ(VTOTAL(pipe)));
I915_WRITE(TRANS_VBLANK(pipe), I915_READ(VBLANK(pipe)));
I915_WRITE(TRANS_VSYNC(pipe), I915_READ(VSYNC(pipe)));
+ I915_WRITE(TRANS_VSYNCSHIFT(pipe), I915_READ(VSYNCSHIFT(pipe)));
intel_fdi_normal_train(crtc);
struct drm_device *dev = crtc->dev;
crtc_funcs->dpms(crtc, DRM_MODE_DPMS_OFF);
+ assert_plane_disabled(dev->dev_private, to_intel_crtc(crtc)->plane);
+ assert_pipe_disabled(dev->dev_private, to_intel_crtc(crtc)->pipe);
if (crtc->fb) {
mutex_lock(&dev->struct_mutex);
- i915_gem_object_unpin(to_intel_framebuffer(crtc->fb)->obj);
+ intel_unpin_fb_obj(to_intel_framebuffer(crtc->fb)->obj);
mutex_unlock(&dev->struct_mutex);
}
}
return false;
}
- /* XXX some encoders set the crtcinfo, others don't.
- * Obviously we need some form of conflict resolution here...
- */
- if (adjusted_mode->crtc_htotal == 0)
- drm_mode_set_crtcinfo(adjusted_mode, 0);
+ /* All interlaced capable intel hw wants timings in frames. */
+ drm_mode_set_crtcinfo(adjusted_mode, 0);
return true;
}
+static int valleyview_get_display_clock_speed(struct drm_device *dev)
+{
+ return 400000; /* FIXME */
+}
+
static int i945_get_display_clock_speed(struct drm_device *dev)
{
return 400000;
2,
G4X_FIFO_LINE_SIZE,
};
+static const struct intel_watermark_params valleyview_wm_info = {
+ VALLEYVIEW_FIFO_SIZE,
+ VALLEYVIEW_MAX_WM,
+ VALLEYVIEW_MAX_WM,
+ 2,
+ G4X_FIFO_LINE_SIZE,
+};
+static const struct intel_watermark_params valleyview_cursor_wm_info = {
+ I965_CURSOR_FIFO,
+ VALLEYVIEW_CURSOR_MAX_WM,
+ I965_CURSOR_DFT_WM,
+ 2,
+ G4X_FIFO_LINE_SIZE,
+};
static const struct intel_watermark_params i965_cursor_wm_info = {
I965_CURSOR_FIFO,
I965_CURSOR_MAX_WM,
display, cursor);
}
+static bool vlv_compute_drain_latency(struct drm_device *dev,
+ int plane,
+ int *plane_prec_mult,
+ int *plane_dl,
+ int *cursor_prec_mult,
+ int *cursor_dl)
+{
+ struct drm_crtc *crtc;
+ int clock, pixel_size;
+ int entries;
+
+ crtc = intel_get_crtc_for_plane(dev, plane);
+ if (crtc->fb == NULL || !crtc->enabled)
+ return false;
+
+ clock = crtc->mode.clock; /* VESA DOT Clock */
+ pixel_size = crtc->fb->bits_per_pixel / 8; /* BPP */
+
+ entries = (clock / 1000) * pixel_size;
+ *plane_prec_mult = (entries > 256) ?
+ DRAIN_LATENCY_PRECISION_32 : DRAIN_LATENCY_PRECISION_16;
+ *plane_dl = (64 * (*plane_prec_mult) * 4) / ((clock / 1000) *
+ pixel_size);
+
+ entries = (clock / 1000) * 4; /* BPP is always 4 for cursor */
+ *cursor_prec_mult = (entries > 256) ?
+ DRAIN_LATENCY_PRECISION_32 : DRAIN_LATENCY_PRECISION_16;
+ *cursor_dl = (64 * (*cursor_prec_mult) * 4) / ((clock / 1000) * 4);
+
+ return true;
+}
+
+/*
+ * Update drain latency registers of memory arbiter
+ *
+ * Valleyview SoC has a new memory arbiter and needs drain latency registers
+ * to be programmed. Each plane has a drain latency multiplier and a drain
+ * latency value.
+ */
+
+static void vlv_update_drain_latency(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ int planea_prec, planea_dl, planeb_prec, planeb_dl;
+ int cursora_prec, cursora_dl, cursorb_prec, cursorb_dl;
+ int plane_prec_mult, cursor_prec_mult; /* Precision multiplier is
+ either 16 or 32 */
+
+ /* For plane A, Cursor A */
+ if (vlv_compute_drain_latency(dev, 0, &plane_prec_mult, &planea_dl,
+ &cursor_prec_mult, &cursora_dl)) {
+ cursora_prec = (cursor_prec_mult == DRAIN_LATENCY_PRECISION_32) ?
+ DDL_CURSORA_PRECISION_32 : DDL_CURSORA_PRECISION_16;
+ planea_prec = (plane_prec_mult == DRAIN_LATENCY_PRECISION_32) ?
+ DDL_PLANEA_PRECISION_32 : DDL_PLANEA_PRECISION_16;
+
+ I915_WRITE(VLV_DDL1, cursora_prec |
+ (cursora_dl << DDL_CURSORA_SHIFT) |
+ planea_prec | planea_dl);
+ }
+
+ /* For plane B, Cursor B */
+ if (vlv_compute_drain_latency(dev, 1, &plane_prec_mult, &planeb_dl,
+ &cursor_prec_mult, &cursorb_dl)) {
+ cursorb_prec = (cursor_prec_mult == DRAIN_LATENCY_PRECISION_32) ?
+ DDL_CURSORB_PRECISION_32 : DDL_CURSORB_PRECISION_16;
+ planeb_prec = (plane_prec_mult == DRAIN_LATENCY_PRECISION_32) ?
+ DDL_PLANEB_PRECISION_32 : DDL_PLANEB_PRECISION_16;
+
+ I915_WRITE(VLV_DDL2, cursorb_prec |
+ (cursorb_dl << DDL_CURSORB_SHIFT) |
+ planeb_prec | planeb_dl);
+ }
+}
+
#define single_plane_enabled(mask) is_power_of_2(mask)
+static void valleyview_update_wm(struct drm_device *dev)
+{
+ static const int sr_latency_ns = 12000;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ int planea_wm, planeb_wm, cursora_wm, cursorb_wm;
+ int plane_sr, cursor_sr;
+ unsigned int enabled = 0;
+
+ vlv_update_drain_latency(dev);
+
+ if (g4x_compute_wm0(dev, 0,
+ &valleyview_wm_info, latency_ns,
+ &valleyview_cursor_wm_info, latency_ns,
+ &planea_wm, &cursora_wm))
+ enabled |= 1;
+
+ if (g4x_compute_wm0(dev, 1,
+ &valleyview_wm_info, latency_ns,
+ &valleyview_cursor_wm_info, latency_ns,
+ &planeb_wm, &cursorb_wm))
+ enabled |= 2;
+
+ plane_sr = cursor_sr = 0;
+ if (single_plane_enabled(enabled) &&
+ g4x_compute_srwm(dev, ffs(enabled) - 1,
+ sr_latency_ns,
+ &valleyview_wm_info,
+ &valleyview_cursor_wm_info,
+ &plane_sr, &cursor_sr))
+ I915_WRITE(FW_BLC_SELF_VLV, FW_CSPWRDWNEN);
+ else
+ I915_WRITE(FW_BLC_SELF_VLV,
+ I915_READ(FW_BLC_SELF_VLV) & ~FW_CSPWRDWNEN);
+
+ DRM_DEBUG_KMS("Setting FIFO watermarks - A: plane=%d, cursor=%d, B: plane=%d, cursor=%d, SR: plane=%d, cursor=%d\n",
+ planea_wm, cursora_wm,
+ planeb_wm, cursorb_wm,
+ plane_sr, cursor_sr);
+
+ I915_WRITE(DSPFW1,
+ (plane_sr << DSPFW_SR_SHIFT) |
+ (cursorb_wm << DSPFW_CURSORB_SHIFT) |
+ (planeb_wm << DSPFW_PLANEB_SHIFT) |
+ planea_wm);
+ I915_WRITE(DSPFW2,
+ (I915_READ(DSPFW2) & DSPFW_CURSORA_MASK) |
+ (cursora_wm << DSPFW_CURSORA_SHIFT));
+ I915_WRITE(DSPFW3,
+ (I915_READ(DSPFW3) | (cursor_sr << DSPFW_CURSOR_SR_SHIFT)));
+}
+
static void g4x_update_wm(struct drm_device *dev)
{
static const int sr_latency_ns = 12000;
{
struct drm_i915_private *dev_priv = dev->dev_private;
int latency = SNB_READ_WM0_LATENCY() * 100; /* In unit 0.1us */
+ u32 val;
int fbc_wm, plane_wm, cursor_wm;
unsigned int enabled;
&sandybridge_display_wm_info, latency,
&sandybridge_cursor_wm_info, latency,
&plane_wm, &cursor_wm)) {
- I915_WRITE(WM0_PIPEA_ILK,
- (plane_wm << WM0_PIPE_PLANE_SHIFT) | cursor_wm);
+ val = I915_READ(WM0_PIPEA_ILK);
+ val &= ~(WM0_PIPE_PLANE_MASK | WM0_PIPE_CURSOR_MASK);
+ I915_WRITE(WM0_PIPEA_ILK, val |
+ ((plane_wm << WM0_PIPE_PLANE_SHIFT) | cursor_wm));
DRM_DEBUG_KMS("FIFO watermarks For pipe A -"
" plane %d, " "cursor: %d\n",
plane_wm, cursor_wm);
&sandybridge_display_wm_info, latency,
&sandybridge_cursor_wm_info, latency,
&plane_wm, &cursor_wm)) {
- I915_WRITE(WM0_PIPEB_ILK,
- (plane_wm << WM0_PIPE_PLANE_SHIFT) | cursor_wm);
+ val = I915_READ(WM0_PIPEB_ILK);
+ val &= ~(WM0_PIPE_PLANE_MASK | WM0_PIPE_CURSOR_MASK);
+ I915_WRITE(WM0_PIPEB_ILK, val |
+ ((plane_wm << WM0_PIPE_PLANE_SHIFT) | cursor_wm));
DRM_DEBUG_KMS("FIFO watermarks For pipe B -"
" plane %d, cursor: %d\n",
plane_wm, cursor_wm);
&sandybridge_display_wm_info, latency,
&sandybridge_cursor_wm_info, latency,
&plane_wm, &cursor_wm)) {
- I915_WRITE(WM0_PIPEC_IVB,
- (plane_wm << WM0_PIPE_PLANE_SHIFT) | cursor_wm);
+ val = I915_READ(WM0_PIPEC_IVB);
+ val &= ~(WM0_PIPE_PLANE_MASK | WM0_PIPE_CURSOR_MASK);
+ I915_WRITE(WM0_PIPEC_IVB, val |
+ ((plane_wm << WM0_PIPE_PLANE_SHIFT) | cursor_wm));
DRM_DEBUG_KMS("FIFO watermarks For pipe C -"
" plane %d, cursor: %d\n",
plane_wm, cursor_wm);
{
struct drm_i915_private *dev_priv = dev->dev_private;
int latency = SNB_READ_WM0_LATENCY() * 100; /* In unit 0.1us */
+ u32 val;
int sprite_wm, reg;
int ret;
return;
}
- I915_WRITE(reg, I915_READ(reg) | (sprite_wm << WM0_PIPE_SPRITE_SHIFT));
+ val = I915_READ(reg);
+ val &= ~WM0_PIPE_SPRITE_MASK;
+ I915_WRITE(reg, val | (sprite_wm << WM0_PIPE_SPRITE_SHIFT));
DRM_DEBUG_KMS("sprite watermarks For pipe %d - %d\n", pipe, sprite_wm);
return display_bpc != bpc;
}
-static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
- struct drm_display_mode *mode,
- struct drm_display_mode *adjusted_mode,
- int x, int y,
- struct drm_framebuffer *old_fb)
+static int i9xx_get_refclk(struct drm_crtc *crtc, int num_connectors)
{
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
- int pipe = intel_crtc->pipe;
- int plane = intel_crtc->plane;
- int refclk, num_connectors = 0;
- intel_clock_t clock, reduced_clock;
- u32 dpll, fp = 0, fp2 = 0, dspcntr, pipeconf;
- bool ok, has_reduced_clock = false, is_sdvo = false, is_dvo = false;
- bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false;
- struct drm_mode_config *mode_config = &dev->mode_config;
- struct intel_encoder *encoder;
- const intel_limit_t *limit;
- int ret;
- u32 temp;
- u32 lvds_sync = 0;
-
- list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
- if (encoder->base.crtc != crtc)
- continue;
-
- switch (encoder->type) {
- case INTEL_OUTPUT_LVDS:
- is_lvds = true;
- break;
- case INTEL_OUTPUT_SDVO:
- case INTEL_OUTPUT_HDMI:
- is_sdvo = true;
- if (encoder->needs_tv_clock)
- is_tv = true;
- break;
- case INTEL_OUTPUT_DVO:
- is_dvo = true;
- break;
- case INTEL_OUTPUT_TVOUT:
- is_tv = true;
- break;
- case INTEL_OUTPUT_ANALOG:
- is_crt = true;
- break;
- case INTEL_OUTPUT_DISPLAYPORT:
- is_dp = true;
- break;
- }
-
- num_connectors++;
- }
+ int refclk;
- if (is_lvds && intel_panel_use_ssc(dev_priv) && num_connectors < 2) {
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) &&
+ intel_panel_use_ssc(dev_priv) && num_connectors < 2) {
refclk = dev_priv->lvds_ssc_freq * 1000;
DRM_DEBUG_KMS("using SSC reference clock of %d MHz\n",
refclk / 1000);
refclk = 48000;
}
- /*
- * Returns a set of divisors for the desired target clock with the given
- * refclk, or FALSE. The returned values represent the clock equation:
- * reflck * (5 * (m1 + 2) + (m2 + 2)) / (n + 2) / p1 / p2.
- */
- limit = intel_limit(crtc, refclk);
- ok = limit->find_pll(limit, crtc, adjusted_mode->clock, refclk, &clock);
- if (!ok) {
- DRM_ERROR("Couldn't find PLL settings for mode!\n");
- return -EINVAL;
- }
-
- /* Ensure that the cursor is valid for the new mode before changing... */
- intel_crtc_update_cursor(crtc, true);
+ return refclk;
+}
- if (is_lvds && dev_priv->lvds_downclock_avail) {
- has_reduced_clock = limit->find_pll(limit, crtc,
- dev_priv->lvds_downclock,
- refclk,
- &reduced_clock);
- if (has_reduced_clock && (clock.p != reduced_clock.p)) {
- /*
- * If the different P is found, it means that we can't
- * switch the display clock by using the FP0/FP1.
- * In such case we will disable the LVDS downclock
- * feature.
- */
- DRM_DEBUG_KMS("Different P is found for "
- "LVDS clock/downclock\n");
- has_reduced_clock = 0;
- }
- }
+static void i9xx_adjust_sdvo_tv_clock(struct drm_display_mode *adjusted_mode,
+ intel_clock_t *clock)
+{
/* SDVO TV has fixed PLL values depend on its clock range,
this mirrors vbios setting. */
- if (is_sdvo && is_tv) {
- if (adjusted_mode->clock >= 100000
- && adjusted_mode->clock < 140500) {
- clock.p1 = 2;
- clock.p2 = 10;
- clock.n = 3;
- clock.m1 = 16;
- clock.m2 = 8;
- } else if (adjusted_mode->clock >= 140500
- && adjusted_mode->clock <= 200000) {
- clock.p1 = 1;
- clock.p2 = 10;
- clock.n = 6;
- clock.m1 = 12;
- clock.m2 = 8;
- }
- }
+ if (adjusted_mode->clock >= 100000
+ && adjusted_mode->clock < 140500) {
+ clock->p1 = 2;
+ clock->p2 = 10;
+ clock->n = 3;
+ clock->m1 = 16;
+ clock->m2 = 8;
+ } else if (adjusted_mode->clock >= 140500
+ && adjusted_mode->clock <= 200000) {
+ clock->p1 = 1;
+ clock->p2 = 10;
+ clock->n = 6;
+ clock->m1 = 12;
+ clock->m2 = 8;
+ }
+}
+
+static void i9xx_update_pll_dividers(struct drm_crtc *crtc,
+ intel_clock_t *clock,
+ intel_clock_t *reduced_clock)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ u32 fp, fp2 = 0;
if (IS_PINEVIEW(dev)) {
- fp = (1 << clock.n) << 16 | clock.m1 << 8 | clock.m2;
- if (has_reduced_clock)
- fp2 = (1 << reduced_clock.n) << 16 |
- reduced_clock.m1 << 8 | reduced_clock.m2;
+ fp = (1 << clock->n) << 16 | clock->m1 << 8 | clock->m2;
+ if (reduced_clock)
+ fp2 = (1 << reduced_clock->n) << 16 |
+ reduced_clock->m1 << 8 | reduced_clock->m2;
} else {
- fp = clock.n << 16 | clock.m1 << 8 | clock.m2;
- if (has_reduced_clock)
- fp2 = reduced_clock.n << 16 | reduced_clock.m1 << 8 |
- reduced_clock.m2;
+ fp = clock->n << 16 | clock->m1 << 8 | clock->m2;
+ if (reduced_clock)
+ fp2 = reduced_clock->n << 16 | reduced_clock->m1 << 8 |
+ reduced_clock->m2;
}
- dpll = DPLL_VGA_MODE_DIS;
+ I915_WRITE(FP0(pipe), fp);
- if (!IS_GEN2(dev)) {
- if (is_lvds)
- dpll |= DPLLB_MODE_LVDS;
+ intel_crtc->lowfreq_avail = false;
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) &&
+ reduced_clock && i915_powersave) {
+ I915_WRITE(FP1(pipe), fp2);
+ intel_crtc->lowfreq_avail = true;
+ } else {
+ I915_WRITE(FP1(pipe), fp);
+ }
+}
+
+static void intel_update_lvds(struct drm_crtc *crtc, intel_clock_t *clock,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ u32 temp, lvds_sync = 0;
+
+ temp = I915_READ(LVDS);
+ temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
+ if (pipe == 1) {
+ temp |= LVDS_PIPEB_SELECT;
+ } else {
+ temp &= ~LVDS_PIPEB_SELECT;
+ }
+ /* set the corresponsding LVDS_BORDER bit */
+ temp |= dev_priv->lvds_border_bits;
+ /* Set the B0-B3 data pairs corresponding to whether we're going to
+ * set the DPLLs for dual-channel mode or not.
+ */
+ if (clock->p2 == 7)
+ temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
+ else
+ temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
+
+ /* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
+ * appropriately here, but we need to look more thoroughly into how
+ * panels behave in the two modes.
+ */
+ /* set the dithering flag on LVDS as needed */
+ if (INTEL_INFO(dev)->gen >= 4) {
+ if (dev_priv->lvds_dither)
+ temp |= LVDS_ENABLE_DITHER;
else
- dpll |= DPLLB_MODE_DAC_SERIAL;
- if (is_sdvo) {
- int pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
- if (pixel_multiplier > 1) {
- if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
- dpll |= (pixel_multiplier - 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
- }
- dpll |= DPLL_DVO_HIGH_SPEED;
- }
- if (is_dp)
- dpll |= DPLL_DVO_HIGH_SPEED;
+ temp &= ~LVDS_ENABLE_DITHER;
+ }
+ if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
+ lvds_sync |= LVDS_HSYNC_POLARITY;
+ if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
+ lvds_sync |= LVDS_VSYNC_POLARITY;
+ if ((temp & (LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY))
+ != lvds_sync) {
+ char flags[2] = "-+";
+ DRM_INFO("Changing LVDS panel from "
+ "(%chsync, %cvsync) to (%chsync, %cvsync)\n",
+ flags[!(temp & LVDS_HSYNC_POLARITY)],
+ flags[!(temp & LVDS_VSYNC_POLARITY)],
+ flags[!(lvds_sync & LVDS_HSYNC_POLARITY)],
+ flags[!(lvds_sync & LVDS_VSYNC_POLARITY)]);
+ temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
+ temp |= lvds_sync;
+ }
+ I915_WRITE(LVDS, temp);
+}
+
+static void i9xx_update_pll(struct drm_crtc *crtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode,
+ intel_clock_t *clock, intel_clock_t *reduced_clock,
+ int num_connectors)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ u32 dpll;
+ bool is_sdvo;
- /* compute bitmask from p1 value */
- if (IS_PINEVIEW(dev))
- dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT_PINEVIEW;
- else {
- dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
- if (IS_G4X(dev) && has_reduced_clock)
- dpll |= (1 << (reduced_clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
- }
- switch (clock.p2) {
- case 5:
- dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_5;
- break;
- case 7:
- dpll |= DPLLB_LVDS_P2_CLOCK_DIV_7;
- break;
- case 10:
- dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_10;
- break;
- case 14:
- dpll |= DPLLB_LVDS_P2_CLOCK_DIV_14;
- break;
+ is_sdvo = intel_pipe_has_type(crtc, INTEL_OUTPUT_SDVO) ||
+ intel_pipe_has_type(crtc, INTEL_OUTPUT_HDMI);
+
+ dpll = DPLL_VGA_MODE_DIS;
+
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
+ dpll |= DPLLB_MODE_LVDS;
+ else
+ dpll |= DPLLB_MODE_DAC_SERIAL;
+ if (is_sdvo) {
+ int pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
+ if (pixel_multiplier > 1) {
+ if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
+ dpll |= (pixel_multiplier - 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
}
- if (INTEL_INFO(dev)->gen >= 4)
- dpll |= (6 << PLL_LOAD_PULSE_PHASE_SHIFT);
- } else {
- if (is_lvds) {
- dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
- } else {
- if (clock.p1 == 2)
- dpll |= PLL_P1_DIVIDE_BY_TWO;
+ dpll |= DPLL_DVO_HIGH_SPEED;
+ }
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT))
+ dpll |= DPLL_DVO_HIGH_SPEED;
+
+ /* compute bitmask from p1 value */
+ if (IS_PINEVIEW(dev))
+ dpll |= (1 << (clock->p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT_PINEVIEW;
+ else {
+ dpll |= (1 << (clock->p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
+ if (IS_G4X(dev) && reduced_clock)
+ dpll |= (1 << (reduced_clock->p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
+ }
+ switch (clock->p2) {
+ case 5:
+ dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_5;
+ break;
+ case 7:
+ dpll |= DPLLB_LVDS_P2_CLOCK_DIV_7;
+ break;
+ case 10:
+ dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_10;
+ break;
+ case 14:
+ dpll |= DPLLB_LVDS_P2_CLOCK_DIV_14;
+ break;
+ }
+ if (INTEL_INFO(dev)->gen >= 4)
+ dpll |= (6 << PLL_LOAD_PULSE_PHASE_SHIFT);
+
+ if (is_sdvo && intel_pipe_has_type(crtc, INTEL_OUTPUT_TVOUT))
+ dpll |= PLL_REF_INPUT_TVCLKINBC;
+ else if (intel_pipe_has_type(crtc, INTEL_OUTPUT_TVOUT))
+ /* XXX: just matching BIOS for now */
+ /* dpll |= PLL_REF_INPUT_TVCLKINBC; */
+ dpll |= 3;
+ else if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) &&
+ intel_panel_use_ssc(dev_priv) && num_connectors < 2)
+ dpll |= PLLB_REF_INPUT_SPREADSPECTRUMIN;
+ else
+ dpll |= PLL_REF_INPUT_DREFCLK;
+
+ dpll |= DPLL_VCO_ENABLE;
+ I915_WRITE(DPLL(pipe), dpll & ~DPLL_VCO_ENABLE);
+ POSTING_READ(DPLL(pipe));
+ udelay(150);
+
+ /* The LVDS pin pair needs to be on before the DPLLs are enabled.
+ * This is an exception to the general rule that mode_set doesn't turn
+ * things on.
+ */
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
+ intel_update_lvds(crtc, clock, adjusted_mode);
+
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT))
+ intel_dp_set_m_n(crtc, mode, adjusted_mode);
+
+ I915_WRITE(DPLL(pipe), dpll);
+
+ /* Wait for the clocks to stabilize. */
+ POSTING_READ(DPLL(pipe));
+ udelay(150);
+
+ if (INTEL_INFO(dev)->gen >= 4) {
+ u32 temp = 0;
+ if (is_sdvo) {
+ temp = intel_mode_get_pixel_multiplier(adjusted_mode);
+ if (temp > 1)
+ temp = (temp - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT;
else
- dpll |= (clock.p1 - 2) << DPLL_FPA01_P1_POST_DIV_SHIFT;
- if (clock.p2 == 4)
- dpll |= PLL_P2_DIVIDE_BY_4;
+ temp = 0;
}
+ I915_WRITE(DPLL_MD(pipe), temp);
+ } else {
+ /* The pixel multiplier can only be updated once the
+ * DPLL is enabled and the clocks are stable.
+ *
+ * So write it again.
+ */
+ I915_WRITE(DPLL(pipe), dpll);
}
+}
- if (is_sdvo && is_tv)
- dpll |= PLL_REF_INPUT_TVCLKINBC;
- else if (is_tv)
+static void i8xx_update_pll(struct drm_crtc *crtc,
+ struct drm_display_mode *adjusted_mode,
+ intel_clock_t *clock,
+ int num_connectors)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ u32 dpll;
+
+ dpll = DPLL_VGA_MODE_DIS;
+
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
+ dpll |= (1 << (clock->p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
+ } else {
+ if (clock->p1 == 2)
+ dpll |= PLL_P1_DIVIDE_BY_TWO;
+ else
+ dpll |= (clock->p1 - 2) << DPLL_FPA01_P1_POST_DIV_SHIFT;
+ if (clock->p2 == 4)
+ dpll |= PLL_P2_DIVIDE_BY_4;
+ }
+
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_TVOUT))
/* XXX: just matching BIOS for now */
/* dpll |= PLL_REF_INPUT_TVCLKINBC; */
dpll |= 3;
- else if (is_lvds && intel_panel_use_ssc(dev_priv) && num_connectors < 2)
+ else if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) &&
+ intel_panel_use_ssc(dev_priv) && num_connectors < 2)
dpll |= PLLB_REF_INPUT_SPREADSPECTRUMIN;
else
dpll |= PLL_REF_INPUT_DREFCLK;
+ dpll |= DPLL_VCO_ENABLE;
+ I915_WRITE(DPLL(pipe), dpll & ~DPLL_VCO_ENABLE);
+ POSTING_READ(DPLL(pipe));
+ udelay(150);
+
+ I915_WRITE(DPLL(pipe), dpll);
+
+ /* Wait for the clocks to stabilize. */
+ POSTING_READ(DPLL(pipe));
+ udelay(150);
+
+ /* The LVDS pin pair needs to be on before the DPLLs are enabled.
+ * This is an exception to the general rule that mode_set doesn't turn
+ * things on.
+ */
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
+ intel_update_lvds(crtc, clock, adjusted_mode);
+
+ /* The pixel multiplier can only be updated once the
+ * DPLL is enabled and the clocks are stable.
+ *
+ * So write it again.
+ */
+ I915_WRITE(DPLL(pipe), dpll);
+}
+
+static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode,
+ int x, int y,
+ struct drm_framebuffer *old_fb)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
+ int refclk, num_connectors = 0;
+ intel_clock_t clock, reduced_clock;
+ u32 dspcntr, pipeconf, vsyncshift;
+ bool ok, has_reduced_clock = false, is_sdvo = false;
+ bool is_lvds = false, is_tv = false, is_dp = false;
+ struct drm_mode_config *mode_config = &dev->mode_config;
+ struct intel_encoder *encoder;
+ const intel_limit_t *limit;
+ int ret;
+
+ list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
+ if (encoder->base.crtc != crtc)
+ continue;
+
+ switch (encoder->type) {
+ case INTEL_OUTPUT_LVDS:
+ is_lvds = true;
+ break;
+ case INTEL_OUTPUT_SDVO:
+ case INTEL_OUTPUT_HDMI:
+ is_sdvo = true;
+ if (encoder->needs_tv_clock)
+ is_tv = true;
+ break;
+ case INTEL_OUTPUT_TVOUT:
+ is_tv = true;
+ break;
+ case INTEL_OUTPUT_DISPLAYPORT:
+ is_dp = true;
+ break;
+ }
+
+ num_connectors++;
+ }
+
+ refclk = i9xx_get_refclk(crtc, num_connectors);
+
+ /*
+ * Returns a set of divisors for the desired target clock with the given
+ * refclk, or FALSE. The returned values represent the clock equation:
+ * reflck * (5 * (m1 + 2) + (m2 + 2)) / (n + 2) / p1 / p2.
+ */
+ limit = intel_limit(crtc, refclk);
+ ok = limit->find_pll(limit, crtc, adjusted_mode->clock, refclk, NULL,
+ &clock);
+ if (!ok) {
+ DRM_ERROR("Couldn't find PLL settings for mode!\n");
+ return -EINVAL;
+ }
+
+ /* Ensure that the cursor is valid for the new mode before changing... */
+ intel_crtc_update_cursor(crtc, true);
+
+ if (is_lvds && dev_priv->lvds_downclock_avail) {
+ /*
+ * Ensure we match the reduced clock's P to the target clock.
+ * If the clocks don't match, we can't switch the display clock
+ * by using the FP0/FP1. In such case we will disable the LVDS
+ * downclock feature.
+ */
+ has_reduced_clock = limit->find_pll(limit, crtc,
+ dev_priv->lvds_downclock,
+ refclk,
+ &clock,
+ &reduced_clock);
+ }
+
+ if (is_sdvo && is_tv)
+ i9xx_adjust_sdvo_tv_clock(adjusted_mode, &clock);
+
+ i9xx_update_pll_dividers(crtc, &clock, has_reduced_clock ?
+ &reduced_clock : NULL);
+
+ if (IS_GEN2(dev))
+ i8xx_update_pll(crtc, adjusted_mode, &clock, num_connectors);
+ else
+ i9xx_update_pll(crtc, mode, adjusted_mode, &clock,
+ has_reduced_clock ? &reduced_clock : NULL,
+ num_connectors);
+
/* setup pipeconf */
pipeconf = I915_READ(PIPECONF(pipe));
/* Set up the display plane register */
dspcntr = DISPPLANE_GAMMA_ENABLE;
- /* Ironlake's plane is forced to pipe, bit 24 is to
- enable color space conversion */
if (pipe == 0)
dspcntr &= ~DISPPLANE_SEL_PIPE_MASK;
else
}
}
- dpll |= DPLL_VCO_ENABLE;
-
DRM_DEBUG_KMS("Mode for pipe %c:\n", pipe == 0 ? 'A' : 'B');
drm_mode_debug_printmodeline(mode);
- I915_WRITE(FP0(pipe), fp);
- I915_WRITE(DPLL(pipe), dpll & ~DPLL_VCO_ENABLE);
-
- POSTING_READ(DPLL(pipe));
- udelay(150);
-
- /* The LVDS pin pair needs to be on before the DPLLs are enabled.
- * This is an exception to the general rule that mode_set doesn't turn
- * things on.
- */
- if (is_lvds) {
- temp = I915_READ(LVDS);
- temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
- if (pipe == 1) {
- temp |= LVDS_PIPEB_SELECT;
- } else {
- temp &= ~LVDS_PIPEB_SELECT;
- }
- /* set the corresponsding LVDS_BORDER bit */
- temp |= dev_priv->lvds_border_bits;
- /* Set the B0-B3 data pairs corresponding to whether we're going to
- * set the DPLLs for dual-channel mode or not.
- */
- if (clock.p2 == 7)
- temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
- else
- temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
-
- /* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
- * appropriately here, but we need to look more thoroughly into how
- * panels behave in the two modes.
- */
- /* set the dithering flag on LVDS as needed */
- if (INTEL_INFO(dev)->gen >= 4) {
- if (dev_priv->lvds_dither)
- temp |= LVDS_ENABLE_DITHER;
- else
- temp &= ~LVDS_ENABLE_DITHER;
- }
- if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
- lvds_sync |= LVDS_HSYNC_POLARITY;
- if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
- lvds_sync |= LVDS_VSYNC_POLARITY;
- if ((temp & (LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY))
- != lvds_sync) {
- char flags[2] = "-+";
- DRM_INFO("Changing LVDS panel from "
- "(%chsync, %cvsync) to (%chsync, %cvsync)\n",
- flags[!(temp & LVDS_HSYNC_POLARITY)],
- flags[!(temp & LVDS_VSYNC_POLARITY)],
- flags[!(lvds_sync & LVDS_HSYNC_POLARITY)],
- flags[!(lvds_sync & LVDS_VSYNC_POLARITY)]);
- temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
- temp |= lvds_sync;
- }
- I915_WRITE(LVDS, temp);
- }
-
- if (is_dp) {
- intel_dp_set_m_n(crtc, mode, adjusted_mode);
- }
-
- I915_WRITE(DPLL(pipe), dpll);
-
- /* Wait for the clocks to stabilize. */
- POSTING_READ(DPLL(pipe));
- udelay(150);
-
- if (INTEL_INFO(dev)->gen >= 4) {
- temp = 0;
- if (is_sdvo) {
- temp = intel_mode_get_pixel_multiplier(adjusted_mode);
- if (temp > 1)
- temp = (temp - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT;
- else
- temp = 0;
- }
- I915_WRITE(DPLL_MD(pipe), temp);
- } else {
- /* The pixel multiplier can only be updated once the
- * DPLL is enabled and the clocks are stable.
- *
- * So write it again.
- */
- I915_WRITE(DPLL(pipe), dpll);
- }
-
- intel_crtc->lowfreq_avail = false;
- if (is_lvds && has_reduced_clock && i915_powersave) {
- I915_WRITE(FP1(pipe), fp2);
- intel_crtc->lowfreq_avail = true;
- if (HAS_PIPE_CXSR(dev)) {
+ if (HAS_PIPE_CXSR(dev)) {
+ if (intel_crtc->lowfreq_avail) {
DRM_DEBUG_KMS("enabling CxSR downclocking\n");
pipeconf |= PIPECONF_CXSR_DOWNCLOCK;
- }
- } else {
- I915_WRITE(FP1(pipe), fp);
- if (HAS_PIPE_CXSR(dev)) {
+ } else {
DRM_DEBUG_KMS("disabling CxSR downclocking\n");
pipeconf &= ~PIPECONF_CXSR_DOWNCLOCK;
}
}
pipeconf &= ~PIPECONF_INTERLACE_MASK;
- if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE) {
+ if (!IS_GEN2(dev) &&
+ adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE) {
pipeconf |= PIPECONF_INTERLACE_W_FIELD_INDICATION;
/* the chip adds 2 halflines automatically */
- adjusted_mode->crtc_vdisplay -= 1;
adjusted_mode->crtc_vtotal -= 1;
- adjusted_mode->crtc_vblank_start -= 1;
adjusted_mode->crtc_vblank_end -= 1;
- adjusted_mode->crtc_vsync_end -= 1;
- adjusted_mode->crtc_vsync_start -= 1;
- } else
+ vsyncshift = adjusted_mode->crtc_hsync_start
+ - adjusted_mode->crtc_htotal/2;
+ } else {
pipeconf |= PIPECONF_PROGRESSIVE;
+ vsyncshift = 0;
+ }
+
+ if (!IS_GEN3(dev))
+ I915_WRITE(VSYNCSHIFT(pipe), vsyncshift);
I915_WRITE(HTOTAL(pipe),
(adjusted_mode->crtc_hdisplay - 1) |
* reflck * (5 * (m1 + 2) + (m2 + 2)) / (n + 2) / p1 / p2.
*/
limit = intel_limit(crtc, refclk);
- ok = limit->find_pll(limit, crtc, adjusted_mode->clock, refclk, &clock);
+ ok = limit->find_pll(limit, crtc, adjusted_mode->clock, refclk, NULL,
+ &clock);
if (!ok) {
DRM_ERROR("Couldn't find PLL settings for mode!\n");
return -EINVAL;
intel_crtc_update_cursor(crtc, true);
if (is_lvds && dev_priv->lvds_downclock_avail) {
+ /*
+ * Ensure we match the reduced clock's P to the target clock.
+ * If the clocks don't match, we can't switch the display clock
+ * by using the FP0/FP1. In such case we will disable the LVDS
+ * downclock feature.
+ */
has_reduced_clock = limit->find_pll(limit, crtc,
dev_priv->lvds_downclock,
refclk,
+ &clock,
&reduced_clock);
- if (has_reduced_clock && (clock.p != reduced_clock.p)) {
- /*
- * If the different P is found, it means that we can't
- * switch the display clock by using the FP0/FP1.
- * In such case we will disable the LVDS downclock
- * feature.
- */
- DRM_DEBUG_KMS("Different P is found for "
- "LVDS clock/downclock\n");
- has_reduced_clock = 0;
- }
}
/* SDVO TV has fixed PLL values depend on its clock range,
this mirrors vbios setting. */
pipeconf &= ~PIPECONF_INTERLACE_MASK;
if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE) {
- pipeconf |= PIPECONF_INTERLACE_W_FIELD_INDICATION;
+ pipeconf |= PIPECONF_INTERLACED_ILK;
/* the chip adds 2 halflines automatically */
- adjusted_mode->crtc_vdisplay -= 1;
adjusted_mode->crtc_vtotal -= 1;
- adjusted_mode->crtc_vblank_start -= 1;
adjusted_mode->crtc_vblank_end -= 1;
- adjusted_mode->crtc_vsync_end -= 1;
- adjusted_mode->crtc_vsync_start -= 1;
- } else
+ I915_WRITE(VSYNCSHIFT(pipe),
+ adjusted_mode->crtc_hsync_start
+ - adjusted_mode->crtc_htotal/2);
+ } else {
pipeconf |= PIPECONF_PROGRESSIVE;
+ I915_WRITE(VSYNCSHIFT(pipe), 0);
+ }
I915_WRITE(HTOTAL(pipe),
(adjusted_mode->crtc_hdisplay - 1) |
intel_wait_for_vblank(dev, pipe);
- if (IS_GEN5(dev)) {
- /* enable address swizzle for tiling buffer */
- temp = I915_READ(DISP_ARB_CTL);
- I915_WRITE(DISP_ARB_CTL, temp | DISP_TILE_SURFACE_SWIZZLING);
- }
-
I915_WRITE(DSPCNTR(plane), dspcntr);
POSTING_READ(DSPCNTR(plane));
uint32_t i;
int len;
int hdmiw_hdmiedid;
+ int aud_config;
int aud_cntl_st;
int aud_cntrl_st2;
if (HAS_PCH_IBX(connector->dev)) {
hdmiw_hdmiedid = IBX_HDMIW_HDMIEDID_A;
+ aud_config = IBX_AUD_CONFIG_A;
aud_cntl_st = IBX_AUD_CNTL_ST_A;
aud_cntrl_st2 = IBX_AUD_CNTL_ST2;
} else {
hdmiw_hdmiedid = CPT_HDMIW_HDMIEDID_A;
+ aud_config = CPT_AUD_CONFIG_A;
aud_cntl_st = CPT_AUD_CNTL_ST_A;
aud_cntrl_st2 = CPT_AUD_CNTRL_ST2;
}
i = to_intel_crtc(crtc)->pipe;
hdmiw_hdmiedid += i * 0x100;
aud_cntl_st += i * 0x100;
+ aud_config += i * 0x100;
DRM_DEBUG_DRIVER("ELD on pipe %c\n", pipe_name(i));
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT)) {
DRM_DEBUG_DRIVER("ELD: DisplayPort detected\n");
eld[5] |= (1 << 2); /* Conn_Type, 0x1 = DisplayPort */
- }
+ I915_WRITE(aud_config, AUD_CONFIG_N_VALUE_INDEX); /* 0x1 = DP */
+ } else
+ I915_WRITE(aud_config, 0);
if (intel_eld_uptodate(connector,
aud_cntrl_st2, eldv,
if (!HAS_PIPE_CXSR(dev) && (dpll & DISPLAY_RATE_SELECT_FPA1)) {
DRM_DEBUG_DRIVER("upclocking LVDS\n");
- /* Unlock panel regs */
- I915_WRITE(PP_CONTROL,
- I915_READ(PP_CONTROL) | PANEL_UNLOCK_REGS);
+ assert_panel_unlocked(dev_priv, pipe);
dpll &= ~DISPLAY_RATE_SELECT_FPA1;
I915_WRITE(dpll_reg, dpll);
dpll = I915_READ(dpll_reg);
if (dpll & DISPLAY_RATE_SELECT_FPA1)
DRM_DEBUG_DRIVER("failed to upclock LVDS!\n");
-
- /* ...and lock them again */
- I915_WRITE(PP_CONTROL, I915_READ(PP_CONTROL) & 0x3);
}
/* Schedule downclock */
if (!HAS_PIPE_CXSR(dev) && intel_crtc->lowfreq_avail) {
DRM_DEBUG_DRIVER("downclocking LVDS\n");
- /* Unlock panel regs */
- I915_WRITE(PP_CONTROL, I915_READ(PP_CONTROL) |
- PANEL_UNLOCK_REGS);
+ assert_panel_unlocked(dev_priv, pipe);
dpll |= DISPLAY_RATE_SELECT_FPA1;
I915_WRITE(dpll_reg, dpll);
dpll = I915_READ(dpll_reg);
if (!(dpll & DISPLAY_RATE_SELECT_FPA1))
DRM_DEBUG_DRIVER("failed to downclock LVDS!\n");
-
- /* ...and lock them again */
- I915_WRITE(PP_CONTROL, I915_READ(PP_CONTROL) & 0x3);
}
}
container_of(__work, struct intel_unpin_work, work);
mutex_lock(&work->dev->struct_mutex);
- i915_gem_object_unpin(work->old_fb_obj);
+ intel_unpin_fb_obj(work->old_fb_obj);
drm_gem_object_unreference(&work->pending_flip_obj->base);
drm_gem_object_unreference(&work->old_fb_obj->base);
MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
OUT_RING(fb->pitches[0]);
OUT_RING(obj->gtt_offset + offset);
- OUT_RING(MI_NOOP);
+ OUT_RING(0); /* aux display base address, unused */
ADVANCE_LP_RING();
out:
return ret;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_encoder *encoder;
bool dpd_is_edp = false;
- bool has_lvds = false;
+ bool has_lvds;
- if (IS_MOBILE(dev) && !IS_I830(dev))
- has_lvds = intel_lvds_init(dev);
+ has_lvds = intel_lvds_init(dev);
if (!has_lvds && !HAS_PCH_SPLIT(dev)) {
/* disable the panel fitter on everything but LVDS */
I915_WRITE(PFIT_CONTROL, 0);
if (I915_READ(HDMIB) & PORT_DETECTED) {
/* PCH SDVOB multiplex with HDMIB */
- found = intel_sdvo_init(dev, PCH_SDVOB);
+ found = intel_sdvo_init(dev, PCH_SDVOB, true);
if (!found)
intel_hdmi_init(dev, HDMIB);
if (!found && (I915_READ(PCH_DP_B) & DP_DETECTED))
if (I915_READ(SDVOB) & SDVO_DETECTED) {
DRM_DEBUG_KMS("probing SDVOB\n");
- found = intel_sdvo_init(dev, SDVOB);
+ found = intel_sdvo_init(dev, SDVOB, true);
if (!found && SUPPORTS_INTEGRATED_HDMI(dev)) {
DRM_DEBUG_KMS("probing HDMI on SDVOB\n");
intel_hdmi_init(dev, SDVOB);
if (I915_READ(SDVOB) & SDVO_DETECTED) {
DRM_DEBUG_KMS("probing SDVOC\n");
- found = intel_sdvo_init(dev, SDVOC);
+ found = intel_sdvo_init(dev, SDVOC, false);
}
if (!found && (I915_READ(SDVOC) & SDVO_DETECTED)) {
case DRM_FORMAT_VYUY:
break;
default:
- DRM_ERROR("unsupported pixel format\n");
+ DRM_DEBUG_KMS("unsupported pixel format %u\n",
+ mode_cmd->pixel_format);
return -EINVAL;
}
u32 rp_state_cap = I915_READ(GEN6_RP_STATE_CAP);
u32 gt_perf_status = I915_READ(GEN6_GT_PERF_STATUS);
u32 pcu_mbox, rc6_mask = 0;
+ u32 gtfifodbg;
int cur_freq, min_freq, max_freq;
int i;
*/
I915_WRITE(GEN6_RC_STATE, 0);
mutex_lock(&dev_priv->dev->struct_mutex);
+
+ /* Clear the DBG now so we don't confuse earlier errors */
+ if ((gtfifodbg = I915_READ(GTFIFODBG))) {
+ DRM_ERROR("GT fifo had a previous error %x\n", gtfifodbg);
+ I915_WRITE(GTFIFODBG, gtfifodbg);
+ }
+
gen6_gt_force_wake_get(dev_priv);
/* disable the counters and set deterministic thresholds */
}
}
+static void valleyview_init_clock_gating(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ int pipe;
+ uint32_t dspclk_gate = VRHUNIT_CLOCK_GATE_DISABLE;
+
+ I915_WRITE(PCH_DSPCLK_GATE_D, dspclk_gate);
+
+ I915_WRITE(WM3_LP_ILK, 0);
+ I915_WRITE(WM2_LP_ILK, 0);
+ I915_WRITE(WM1_LP_ILK, 0);
+
+ /* According to the spec, bit 13 (RCZUNIT) must be set on IVB.
+ * This implements the WaDisableRCZUnitClockGating workaround.
+ */
+ I915_WRITE(GEN6_UCGCTL2, GEN6_RCZUNIT_CLOCK_GATE_DISABLE);
+
+ I915_WRITE(ILK_DSPCLK_GATE, IVB_VRHUNIT_CLK_GATE);
+
+ I915_WRITE(IVB_CHICKEN3,
+ CHICKEN3_DGMG_REQ_OUT_FIX_DISABLE |
+ CHICKEN3_DGMG_DONE_FIX_DISABLE);
+
+ /* Apply the WaDisableRHWOOptimizationForRenderHang workaround. */
+ I915_WRITE(GEN7_COMMON_SLICE_CHICKEN1,
+ GEN7_CSC1_RHWO_OPT_DISABLE_IN_RCC);
+
+ /* WaApplyL3ControlAndL3ChickenMode requires those two on Ivy Bridge */
+ I915_WRITE(GEN7_L3CNTLREG1, GEN7_WA_FOR_GEN7_L3_CONTROL);
+ I915_WRITE(GEN7_L3_CHICKEN_MODE_REGISTER, GEN7_WA_L3_CHICKEN_MODE);
+
+ /* This is required by WaCatErrorRejectionIssue */
+ I915_WRITE(GEN7_SQ_CHICKEN_MBCUNIT_CONFIG,
+ I915_READ(GEN7_SQ_CHICKEN_MBCUNIT_CONFIG) |
+ GEN7_SQ_CHICKEN_MBCUNIT_SQINTMOB);
+
+ for_each_pipe(pipe) {
+ I915_WRITE(DSPCNTR(pipe),
+ I915_READ(DSPCNTR(pipe)) |
+ DISPPLANE_TRICKLE_FEED_DISABLE);
+ intel_flush_display_plane(dev_priv, pipe);
+ }
+
+ I915_WRITE(CACHE_MODE_1, I915_READ(CACHE_MODE_1) |
+ (PIXEL_SUBSPAN_COLLECT_OPT_DISABLE << 16) |
+ PIXEL_SUBSPAN_COLLECT_OPT_DISABLE);
+}
+
static void g4x_init_clock_gating(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
}
/* Returns the core display clock speed */
- if (IS_I945G(dev) || (IS_G33(dev) && !IS_PINEVIEW_M(dev)))
+ if (IS_VALLEYVIEW(dev))
+ dev_priv->display.get_display_clock_speed =
+ valleyview_get_display_clock_speed;
+ else if (IS_I945G(dev) || (IS_G33(dev) && !IS_PINEVIEW_M(dev)))
dev_priv->display.get_display_clock_speed =
i945_get_display_clock_speed;
else if (IS_I915G(dev))
dev_priv->display.write_eld = ironlake_write_eld;
} else
dev_priv->display.update_wm = NULL;
+ } else if (IS_VALLEYVIEW(dev)) {
+ dev_priv->display.update_wm = valleyview_update_wm;
+ dev_priv->display.init_clock_gating =
+ valleyview_init_clock_gating;
} else if (IS_PINEVIEW(dev)) {
if (!intel_get_cxsr_latency(IS_PINEVIEW_G(dev),
dev_priv->is_ddr3,
dev_priv->quirks |= QUIRK_LVDS_SSC_DISABLE;
}
+/*
+ * A machine (e.g. Acer Aspire 5734Z) may need to invert the panel backlight
+ * brightness value
+ */
+static void quirk_invert_brightness(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ dev_priv->quirks |= QUIRK_INVERT_BRIGHTNESS;
+}
+
struct intel_quirk {
int device;
int subsystem_vendor;
};
struct intel_quirk intel_quirks[] = {
- /* HP Compaq 2730p needs pipe A force quirk (LP: #291555) */
- { 0x2a42, 0x103c, 0x30eb, quirk_pipea_force },
/* HP Mini needs pipe A force quirk (LP: #322104) */
{ 0x27ae, 0x103c, 0x361a, quirk_pipea_force },
/* Sony Vaio Y cannot use SSC on LVDS */
{ 0x0046, 0x104d, 0x9076, quirk_ssc_force_disable },
+
+ /* Acer Aspire 5734Z must invert backlight brightness */
+ { 0x2a42, 0x1025, 0x0459, quirk_invert_brightness },
};
static void intel_init_quirks(struct drm_device *dev)
dev->mode_config.min_width = 0;
dev->mode_config.min_height = 0;
+ dev->mode_config.preferred_depth = 24;
+ dev->mode_config.prefer_shadow = 1;
+
dev->mode_config.funcs = (void *)&intel_mode_funcs;
intel_init_quirks(dev);
if (IS_IRONLAKE_M(dev))
ironlake_disable_rc6(dev);
+ if (IS_VALLEYVIEW(dev))
+ vlv_init_dpio(dev);
+
mutex_unlock(&dev->struct_mutex);
/* Disable the irq before mode object teardown, for the irq might
projects / firefly-linux-kernel-4.4.55.git / blobdiff