model = "ST-Ericsson HREF (v60+) platform with Device Tree";
compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
- gpio_keys {
- button@1 {
- gpios = <&gpio5 25 0x4>;
- };
- };
-
soc {
// External Micro SD slot
sdi0_per1@80126000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <4>;
- mmc-cap-sd-highspeed;
- mmc-cap-mmc-highspeed;
- vmmc-supply = <&ab8500_ldo_aux3_reg>;
-
cd-gpios = <&gpio2 31 0x4>; // 95
-
- status = "okay";
};
- // WLAN SDIO channel
- sdi1_per2@80118000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <4>;
-
- status = "okay";
- };
-
- // PoP:ed eMMC
- sdi2_per3@80005000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <8>;
- mmc-cap-mmc-highspeed;
-
- status = "okay";
+ vmmci: regulator-gpio {
+ gpios = <&gpio0 5 0x4>;
+ enable-gpio = <&gpio5 9 0x4>;
};
- // On-board eMMC
- sdi4_per2@80114000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <8>;
- mmc-cap-mmc-highspeed;
- vmmc-supply = <&ab8500_ldo_aux2_reg>;
+ pinctrl {
+ /*
+ * Set this up using hogs, as time goes by and as seems fit, these
+ * can be moved over to being controlled by respective device.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ipgpio_hrefv60_mode>,
+ <&accel_hrefv60_mode>,
+ <&magneto_hrefv60_mode>,
+ <&etm_hrefv60_mode>,
+ <&nahj_hrefv60_mode>,
+ <&nfc_hrefv60_mode>,
+ <&force_hrefv60_mode>,
+ <&dipro_hrefv60_mode>,
+ <&vaudio_hf_hrefv60_mode>,
+ <&gbf_hrefv60_mode>,
+ <&hdtv_hrefv60_mode>,
+ <&touch_hrefv60_mode>;
- status = "okay";
+ sdi0 {
+ /* SD card detect GPIO pin, extend default state */
+ sdi0_default_mode: sdi0_default {
+ default_hrefv60_cfg1 {
+ ste,pins = "GPIO95_E8";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ ipgpio {
+ /*
+ * XENON Flashgun on image processor GPIO (controlled from image
+ * processor firmware), mux in these image processor GPIO lines 0
+ * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+ * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+ * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+ */
+ ipgpio_hrefv60_mode: ipgpio_hrefv60 {
+ hrefv60_mux {
+ ste,function = "ipgpio";
+ ste,pins = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
+ };
+ hrefv60_cfg1 {
+ ste,pins = "GPIO6_AF6", "GPIO7_AG5";
+ ste,config = <&in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO21_AB3";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg3 {
+ ste,pins = "GPIO64_F3";
+ ste,config = <&out_lo>;
+ };
+ };
+ };
+ accelerometer {
+ accel_hrefv60_mode: accel_hrefv60 {
+ /* Accelerometer interrupt lines 1 & 2 */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO82_C1", "GPIO83_D3";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ magnetometer {
+ magneto_hrefv60_mode: magneto_hrefv60 {
+ /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO31_V3";
+ ste,config = <&gpio_in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO32_V2";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ etm {
+ /*
+ * Drive D19-D23 for the ETM PTM trace interface low,
+ * (presumably pins are unconnected therefore grounded here,
+ * the "other alt C1" setting enables these pins)
+ */
+ etm_hrefv60_mode: etm_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins =
+ "GPIO70_G5",
+ "GPIO71_G4",
+ "GPIO72_H4",
+ "GPIO73_H3",
+ "GPIO74_J3";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ nahj {
+ nahj_hrefv60_mode: nahj_hrefv60 {
+ /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO76_J2";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO216_AG12";
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ nfc {
+ nfc_hrefv60_mode: nfc_hrefv60 {
+ /* NFC ENA and RESET to low, pulldown IRQ line */
+ hrefv60_cfg1 {
+ ste,pins =
+ "GPIO77_H1", /* NFC_ENA */
+ "GPIO142_C11"; /* NFC_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO144_B13"; /* NFC_IRQ */
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ force {
+ force_hrefv60_mode: force_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins = "GPIO91_B6"; /* FORCE_SENSING_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins =
+ "GPIO92_D6", /* FORCE_SENSING_RST */
+ "GPIO97_D9"; /* FORCE_SENSING_WU */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ dipro {
+ dipro_hrefv60_mode: dipro_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins = "GPIO139_C9"; /* DIPRO_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ vaudio_hf {
+ vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 {
+ /* Audio Amplifier HF enable GPIO */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ gbf {
+ gbf_hrefv60_mode: gbf_hrefv60 {
+ /*
+ * GBF (GPS, Bluetooth, FM-radio) interface,
+ * pull low to reset state
+ */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ hdtv {
+ hdtv_hrefv60_mode: hdtv_hrefv60 {
+ /* MSP : HDTV INTERFACE GPIO line */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO192_AJ27";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ touch {
+ touch_hrefv60_mode: touch_hrefv60 {
+ /*
+ * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
+ * GPIO 67 for interrupts. Pull-up the IRQ line and drive both
+ * reset signals low.
+ */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO143_D12", "GPIO146_D13";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO67_G2";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ mcde {
+ lcd_hrefv60_mode: lcd_hrefv60 {
+ /*
+ * Display Interface 1 uses GPIO 65 for RST (reset).
+ * Display Interface 2 uses GPIO 66 for RST (reset).
+ * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
+ */
+ hrefv60_cfg1 {
+ ste,pins ="GPIO65_F1";
+ ste,config = <&gpio_out_hi>;
+ };
+ hrefv60_cfg2 {
+ ste,pins ="GPIO66_G3";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
};
};
};
projects / firefly-linux-kernel-4.4.55.git / blobdiff