2 * mac80211 <-> driver interface
4 * Copyright 2002-2005, Devicescape Software, Inc.
5 * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
6 * Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net>
7 * Copyright 2013-2014 Intel Mobile Communications GmbH
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License version 2 as
11 * published by the Free Software Foundation.
17 #include <linux/bug.h>
18 #include <linux/kernel.h>
19 #include <linux/if_ether.h>
20 #include <linux/skbuff.h>
21 #include <linux/ieee80211.h>
22 #include <net/cfg80211.h>
23 #include <asm/unaligned.h>
28 * mac80211 is the Linux stack for 802.11 hardware that implements
29 * only partial functionality in hard- or firmware. This document
30 * defines the interface between mac80211 and low-level hardware
35 * DOC: Calling mac80211 from interrupts
37 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
38 * called in hardware interrupt context. The low-level driver must not call any
39 * other functions in hardware interrupt context. If there is a need for such
40 * call, the low-level driver should first ACK the interrupt and perform the
41 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
44 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
45 * use the non-IRQ-safe functions!
51 * If you're reading this document and not the header file itself, it will
52 * be incomplete because not all documentation has been converted yet.
58 * As a general rule, when frames are passed between mac80211 and the driver,
59 * they start with the IEEE 802.11 header and include the same octets that are
60 * sent over the air except for the FCS which should be calculated by the
63 * There are, however, various exceptions to this rule for advanced features:
65 * The first exception is for hardware encryption and decryption offload
66 * where the IV/ICV may or may not be generated in hardware.
68 * Secondly, when the hardware handles fragmentation, the frame handed to
69 * the driver from mac80211 is the MSDU, not the MPDU.
73 * DOC: mac80211 workqueue
75 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
76 * The workqueue is a single threaded workqueue and can only be accessed by
77 * helpers for sanity checking. Drivers must ensure all work added onto the
78 * mac80211 workqueue should be cancelled on the driver stop() callback.
80 * mac80211 will flushed the workqueue upon interface removal and during
83 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
88 * DOC: mac80211 software tx queueing
90 * mac80211 provides an optional intermediate queueing implementation designed
91 * to allow the driver to keep hardware queues short and provide some fairness
92 * between different stations/interfaces.
93 * In this model, the driver pulls data frames from the mac80211 queue instead
94 * of letting mac80211 push them via drv_tx().
95 * Other frames (e.g. control or management) are still pushed using drv_tx().
97 * Drivers indicate that they use this model by implementing the .wake_tx_queue
100 * Intermediate queues (struct ieee80211_txq) are kept per-sta per-tid, with a
101 * single per-vif queue for multicast data frames.
103 * The driver is expected to initialize its private per-queue data for stations
104 * and interfaces in the .add_interface and .sta_add ops.
106 * The driver can't access the queue directly. To dequeue a frame, it calls
107 * ieee80211_tx_dequeue(). Whenever mac80211 adds a new frame to a queue, it
108 * calls the .wake_tx_queue driver op.
110 * For AP powersave TIM handling, the driver only needs to indicate if it has
111 * buffered packets in the driver specific data structures by calling
112 * ieee80211_sta_set_buffered(). For frames buffered in the ieee80211_txq
113 * struct, mac80211 sets the appropriate TIM PVB bits and calls
114 * .release_buffered_frames().
115 * In that callback the driver is therefore expected to release its own
116 * buffered frames and afterwards also frames from the ieee80211_txq (obtained
117 * via the usual ieee80211_tx_dequeue).
123 * enum ieee80211_max_queues - maximum number of queues
125 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
126 * @IEEE80211_MAX_QUEUE_MAP: bitmap with maximum queues set
128 enum ieee80211_max_queues {
129 IEEE80211_MAX_QUEUES = 16,
130 IEEE80211_MAX_QUEUE_MAP = BIT(IEEE80211_MAX_QUEUES) - 1,
133 #define IEEE80211_INVAL_HW_QUEUE 0xff
136 * enum ieee80211_ac_numbers - AC numbers as used in mac80211
137 * @IEEE80211_AC_VO: voice
138 * @IEEE80211_AC_VI: video
139 * @IEEE80211_AC_BE: best effort
140 * @IEEE80211_AC_BK: background
142 enum ieee80211_ac_numbers {
148 #define IEEE80211_NUM_ACS 4
151 * struct ieee80211_tx_queue_params - transmit queue configuration
153 * The information provided in this structure is required for QoS
154 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
156 * @aifs: arbitration interframe space [0..255]
157 * @cw_min: minimum contention window [a value of the form
158 * 2^n-1 in the range 1..32767]
159 * @cw_max: maximum contention window [like @cw_min]
160 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
161 * @acm: is mandatory admission control required for the access category
162 * @uapsd: is U-APSD mode enabled for the queue
164 struct ieee80211_tx_queue_params {
173 struct ieee80211_low_level_stats {
174 unsigned int dot11ACKFailureCount;
175 unsigned int dot11RTSFailureCount;
176 unsigned int dot11FCSErrorCount;
177 unsigned int dot11RTSSuccessCount;
181 * enum ieee80211_chanctx_change - change flag for channel context
182 * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed
183 * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed
184 * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed
185 * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel,
186 * this is used only with channel switching with CSA
187 * @IEEE80211_CHANCTX_CHANGE_MIN_WIDTH: The min required channel width changed
189 enum ieee80211_chanctx_change {
190 IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0),
191 IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1),
192 IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2),
193 IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3),
194 IEEE80211_CHANCTX_CHANGE_MIN_WIDTH = BIT(4),
198 * struct ieee80211_chanctx_conf - channel context that vifs may be tuned to
200 * This is the driver-visible part. The ieee80211_chanctx
201 * that contains it is visible in mac80211 only.
203 * @def: the channel definition
204 * @min_def: the minimum channel definition currently required.
205 * @rx_chains_static: The number of RX chains that must always be
206 * active on the channel to receive MIMO transmissions
207 * @rx_chains_dynamic: The number of RX chains that must be enabled
208 * after RTS/CTS handshake to receive SMPS MIMO transmissions;
209 * this will always be >= @rx_chains_static.
210 * @radar_enabled: whether radar detection is enabled on this channel.
211 * @drv_priv: data area for driver use, will always be aligned to
212 * sizeof(void *), size is determined in hw information.
214 struct ieee80211_chanctx_conf {
215 struct cfg80211_chan_def def;
216 struct cfg80211_chan_def min_def;
218 u8 rx_chains_static, rx_chains_dynamic;
222 u8 drv_priv[0] __aligned(sizeof(void *));
226 * enum ieee80211_chanctx_switch_mode - channel context switch mode
227 * @CHANCTX_SWMODE_REASSIGN_VIF: Both old and new contexts already
228 * exist (and will continue to exist), but the virtual interface
229 * needs to be switched from one to the other.
230 * @CHANCTX_SWMODE_SWAP_CONTEXTS: The old context exists but will stop
231 * to exist with this call, the new context doesn't exist but
232 * will be active after this call, the virtual interface switches
233 * from the old to the new (note that the driver may of course
234 * implement this as an on-the-fly chandef switch of the existing
235 * hardware context, but the mac80211 pointer for the old context
236 * will cease to exist and only the new one will later be used
237 * for changes/removal.)
239 enum ieee80211_chanctx_switch_mode {
240 CHANCTX_SWMODE_REASSIGN_VIF,
241 CHANCTX_SWMODE_SWAP_CONTEXTS,
245 * struct ieee80211_vif_chanctx_switch - vif chanctx switch information
247 * This is structure is used to pass information about a vif that
248 * needs to switch from one chanctx to another. The
249 * &ieee80211_chanctx_switch_mode defines how the switch should be
252 * @vif: the vif that should be switched from old_ctx to new_ctx
253 * @old_ctx: the old context to which the vif was assigned
254 * @new_ctx: the new context to which the vif must be assigned
256 struct ieee80211_vif_chanctx_switch {
257 struct ieee80211_vif *vif;
258 struct ieee80211_chanctx_conf *old_ctx;
259 struct ieee80211_chanctx_conf *new_ctx;
263 * enum ieee80211_bss_change - BSS change notification flags
265 * These flags are used with the bss_info_changed() callback
266 * to indicate which BSS parameter changed.
268 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
269 * also implies a change in the AID.
270 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
271 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
272 * @BSS_CHANGED_ERP_SLOT: slot timing changed
273 * @BSS_CHANGED_HT: 802.11n parameters changed
274 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
275 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
276 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
277 * reason (IBSS and managed mode)
278 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
279 * new beacon (beaconing modes)
280 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
281 * enabled/disabled (beaconing modes)
282 * @BSS_CHANGED_CQM: Connection quality monitor config changed
283 * @BSS_CHANGED_IBSS: IBSS join status changed
284 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
285 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
286 * that it is only ever disabled for station mode.
287 * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
288 * @BSS_CHANGED_SSID: SSID changed for this BSS (AP and IBSS mode)
289 * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode)
290 * @BSS_CHANGED_PS: PS changed for this BSS (STA mode)
291 * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface
292 * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS)
293 * changed (currently only in P2P client mode, GO mode will be later)
294 * @BSS_CHANGED_BEACON_INFO: Data from the AP's beacon became available:
295 * currently dtim_period only is under consideration.
296 * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed,
297 * note that this is only called when it changes after the channel
298 * context had been assigned.
299 * @BSS_CHANGED_OCB: OCB join status changed
301 enum ieee80211_bss_change {
302 BSS_CHANGED_ASSOC = 1<<0,
303 BSS_CHANGED_ERP_CTS_PROT = 1<<1,
304 BSS_CHANGED_ERP_PREAMBLE = 1<<2,
305 BSS_CHANGED_ERP_SLOT = 1<<3,
306 BSS_CHANGED_HT = 1<<4,
307 BSS_CHANGED_BASIC_RATES = 1<<5,
308 BSS_CHANGED_BEACON_INT = 1<<6,
309 BSS_CHANGED_BSSID = 1<<7,
310 BSS_CHANGED_BEACON = 1<<8,
311 BSS_CHANGED_BEACON_ENABLED = 1<<9,
312 BSS_CHANGED_CQM = 1<<10,
313 BSS_CHANGED_IBSS = 1<<11,
314 BSS_CHANGED_ARP_FILTER = 1<<12,
315 BSS_CHANGED_QOS = 1<<13,
316 BSS_CHANGED_IDLE = 1<<14,
317 BSS_CHANGED_SSID = 1<<15,
318 BSS_CHANGED_AP_PROBE_RESP = 1<<16,
319 BSS_CHANGED_PS = 1<<17,
320 BSS_CHANGED_TXPOWER = 1<<18,
321 BSS_CHANGED_P2P_PS = 1<<19,
322 BSS_CHANGED_BEACON_INFO = 1<<20,
323 BSS_CHANGED_BANDWIDTH = 1<<21,
324 BSS_CHANGED_OCB = 1<<22,
326 /* when adding here, make sure to change ieee80211_reconfig */
330 * The maximum number of IPv4 addresses listed for ARP filtering. If the number
331 * of addresses for an interface increase beyond this value, hardware ARP
332 * filtering will be disabled.
334 #define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4
337 * enum ieee80211_event_type - event to be notified to the low level driver
338 * @RSSI_EVENT: AP's rssi crossed the a threshold set by the driver.
339 * @MLME_EVENT: event related to MLME
340 * @BAR_RX_EVENT: a BAR was received
341 * @BA_FRAME_TIMEOUT: Frames were released from the reordering buffer because
342 * they timed out. This won't be called for each frame released, but only
343 * once each time the timeout triggers.
345 enum ieee80211_event_type {
353 * enum ieee80211_rssi_event_data - relevant when event type is %RSSI_EVENT
354 * @RSSI_EVENT_HIGH: AP's rssi went below the threshold set by the driver.
355 * @RSSI_EVENT_LOW: AP's rssi went above the threshold set by the driver.
357 enum ieee80211_rssi_event_data {
363 * struct ieee80211_rssi_event - data attached to an %RSSI_EVENT
364 * @data: See &enum ieee80211_rssi_event_data
366 struct ieee80211_rssi_event {
367 enum ieee80211_rssi_event_data data;
371 * enum ieee80211_mlme_event_data - relevant when event type is %MLME_EVENT
372 * @AUTH_EVENT: the MLME operation is authentication
373 * @ASSOC_EVENT: the MLME operation is association
374 * @DEAUTH_RX_EVENT: deauth received..
375 * @DEAUTH_TX_EVENT: deauth sent.
377 enum ieee80211_mlme_event_data {
385 * enum ieee80211_mlme_event_status - relevant when event type is %MLME_EVENT
386 * @MLME_SUCCESS: the MLME operation completed successfully.
387 * @MLME_DENIED: the MLME operation was denied by the peer.
388 * @MLME_TIMEOUT: the MLME operation timed out.
390 enum ieee80211_mlme_event_status {
397 * struct ieee80211_mlme_event - data attached to an %MLME_EVENT
398 * @data: See &enum ieee80211_mlme_event_data
399 * @status: See &enum ieee80211_mlme_event_status
400 * @reason: the reason code if applicable
402 struct ieee80211_mlme_event {
403 enum ieee80211_mlme_event_data data;
404 enum ieee80211_mlme_event_status status;
409 * struct ieee80211_ba_event - data attached for BlockAck related events
410 * @sta: pointer to the &ieee80211_sta to which this event relates
412 * @ssn: the starting sequence number (for %BAR_RX_EVENT)
414 struct ieee80211_ba_event {
415 struct ieee80211_sta *sta;
421 * struct ieee80211_event - event to be sent to the driver
422 * @type: The event itself. See &enum ieee80211_event_type.
423 * @rssi: relevant if &type is %RSSI_EVENT
424 * @mlme: relevant if &type is %AUTH_EVENT
425 * @ba: relevant if &type is %BAR_RX_EVENT or %BA_FRAME_TIMEOUT
426 * @u:union holding the fields above
428 struct ieee80211_event {
429 enum ieee80211_event_type type;
431 struct ieee80211_rssi_event rssi;
432 struct ieee80211_mlme_event mlme;
433 struct ieee80211_ba_event ba;
438 * struct ieee80211_bss_conf - holds the BSS's changing parameters
440 * This structure keeps information about a BSS (and an association
441 * to that BSS) that can change during the lifetime of the BSS.
443 * @assoc: association status
444 * @ibss_joined: indicates whether this station is part of an IBSS
446 * @ibss_creator: indicates if a new IBSS network is being created
447 * @aid: association ID number, valid only when @assoc is true
448 * @use_cts_prot: use CTS protection
449 * @use_short_preamble: use 802.11b short preamble;
450 * if the hardware cannot handle this it must set the
451 * IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
452 * @use_short_slot: use short slot time (only relevant for ERP);
453 * if the hardware cannot handle this it must set the
454 * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
455 * @dtim_period: num of beacons before the next DTIM, for beaconing,
456 * valid in station mode only if after the driver was notified
457 * with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then.
458 * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old
459 * as it may have been received during scanning long ago). If the
460 * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can
461 * only come from a beacon, but might not become valid until after
462 * association when a beacon is received (which is notified with the
463 * %BSS_CHANGED_DTIM flag.). See also sync_dtim_count important notice.
464 * @sync_device_ts: the device timestamp corresponding to the sync_tsf,
465 * the driver/device can use this to calculate synchronisation
466 * (see @sync_tsf). See also sync_dtim_count important notice.
467 * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY
468 * is requested, see @sync_tsf/@sync_device_ts.
469 * IMPORTANT: These three sync_* parameters would possibly be out of sync
470 * by the time the driver will use them. The synchronized view is currently
471 * guaranteed only in certain callbacks.
472 * @beacon_int: beacon interval
473 * @assoc_capability: capabilities taken from assoc resp
474 * @basic_rates: bitmap of basic rates, each bit stands for an
475 * index into the rate table configured by the driver in
477 * @beacon_rate: associated AP's beacon TX rate
478 * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
479 * @bssid: The BSSID for this BSS
480 * @enable_beacon: whether beaconing should be enabled or not
481 * @chandef: Channel definition for this BSS -- the hardware might be
482 * configured a higher bandwidth than this BSS uses, for example.
483 * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation.
484 * This field is only valid when the channel type is one of the HT types.
485 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
487 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
488 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
489 * may filter ARP queries targeted for other addresses than listed here.
490 * The driver must allow ARP queries targeted for all address listed here
491 * to pass through. An empty list implies no ARP queries need to pass.
492 * @arp_addr_cnt: Number of addresses currently on the list. Note that this
493 * may be larger than %IEEE80211_BSS_ARP_ADDR_LIST_LEN (the arp_addr_list
494 * array size), it's up to the driver what to do in that case.
495 * @qos: This is a QoS-enabled BSS.
496 * @idle: This interface is idle. There's also a global idle flag in the
497 * hardware config which may be more appropriate depending on what
498 * your driver/device needs to do.
499 * @ps: power-save mode (STA only). This flag is NOT affected by
500 * offchannel/dynamic_ps operations.
501 * @ssid: The SSID of the current vif. Valid in AP and IBSS mode.
502 * @ssid_len: Length of SSID given in @ssid.
503 * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode.
504 * @txpower: TX power in dBm
505 * @txpower_type: TX power adjustment used to control per packet Transmit
506 * Power Control (TPC) in lower driver for the current vif. In particular
507 * TPC is enabled if value passed in %txpower_type is
508 * NL80211_TX_POWER_LIMITED (allow using less than specified from
509 * userspace), whereas TPC is disabled if %txpower_type is set to
510 * NL80211_TX_POWER_FIXED (use value configured from userspace)
511 * @p2p_noa_attr: P2P NoA attribute for P2P powersave
513 struct ieee80211_bss_conf {
515 /* association related data */
516 bool assoc, ibss_joined;
519 /* erp related data */
521 bool use_short_preamble;
526 u16 assoc_capability;
531 struct ieee80211_rate *beacon_rate;
532 int mcast_rate[IEEE80211_NUM_BANDS];
533 u16 ht_operation_mode;
536 struct cfg80211_chan_def chandef;
537 __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
542 u8 ssid[IEEE80211_MAX_SSID_LEN];
546 enum nl80211_tx_power_setting txpower_type;
547 struct ieee80211_p2p_noa_attr p2p_noa_attr;
551 * enum mac80211_tx_info_flags - flags to describe transmission information/status
553 * These flags are used with the @flags member of &ieee80211_tx_info.
555 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
556 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
557 * number to this frame, taking care of not overwriting the fragment
558 * number and increasing the sequence number only when the
559 * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
560 * assign sequence numbers to QoS-data frames but cannot do so correctly
561 * for non-QoS-data and management frames because beacons need them from
562 * that counter as well and mac80211 cannot guarantee proper sequencing.
563 * If this flag is set, the driver should instruct the hardware to
564 * assign a sequence number to the frame or assign one itself. Cf. IEEE
565 * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
566 * beacons and always be clear for frames without a sequence number field.
567 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
568 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
570 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
571 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
572 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
573 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
574 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
575 * because the destination STA was in powersave mode. Note that to
576 * avoid race conditions, the filter must be set by the hardware or
577 * firmware upon receiving a frame that indicates that the station
578 * went to sleep (must be done on device to filter frames already on
579 * the queue) and may only be unset after mac80211 gives the OK for
580 * that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
581 * since only then is it guaranteed that no more frames are in the
583 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
584 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
585 * is for the whole aggregation.
586 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
587 * so consider using block ack request (BAR).
588 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
589 * set by rate control algorithms to indicate probe rate, will
590 * be cleared for fragmented frames (except on the last fragment)
591 * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate
592 * that a frame can be transmitted while the queues are stopped for
593 * off-channel operation.
594 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
595 * used to indicate that a pending frame requires TX processing before
596 * it can be sent out.
597 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
598 * used to indicate that a frame was already retried due to PS
599 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
600 * used to indicate frame should not be encrypted
601 * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll
602 * frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must
603 * be sent although the station is in powersave mode.
604 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
605 * transmit function after the current frame, this can be used
606 * by drivers to kick the DMA queue only if unset or when the
608 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
609 * after TX status because the destination was asleep, it must not
610 * be modified again (no seqno assignment, crypto, etc.)
611 * @IEEE80211_TX_INTFL_MLME_CONN_TX: This frame was transmitted by the MLME
612 * code for connection establishment, this indicates that its status
613 * should kick the MLME state machine.
614 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
615 * MLME command (internal to mac80211 to figure out whether to send TX
616 * status to user space)
617 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
618 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
619 * frame and selects the maximum number of streams that it can use.
620 * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on
621 * the off-channel channel when a remain-on-channel offload is done
622 * in hardware -- normal packets still flow and are expected to be
623 * handled properly by the device.
624 * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP
625 * testing. It will be sent out with incorrect Michael MIC key to allow
626 * TKIP countermeasures to be tested.
627 * @IEEE80211_TX_CTL_NO_CCK_RATE: This frame will be sent at non CCK rate.
628 * This flag is actually used for management frame especially for P2P
629 * frames not being sent at CCK rate in 2GHz band.
630 * @IEEE80211_TX_STATUS_EOSP: This packet marks the end of service period,
631 * when its status is reported the service period ends. For frames in
632 * an SP that mac80211 transmits, it is already set; for driver frames
633 * the driver may set this flag. It is also used to do the same for
635 * @IEEE80211_TX_CTL_USE_MINRATE: This frame will be sent at lowest rate.
636 * This flag is used to send nullfunc frame at minimum rate when
637 * the nullfunc is used for connection monitoring purpose.
638 * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it
639 * would be fragmented by size (this is optional, only used for
640 * monitor injection).
641 * @IEEE80211_TX_STAT_NOACK_TRANSMITTED: A frame that was marked with
642 * IEEE80211_TX_CTL_NO_ACK has been successfully transmitted without
643 * any errors (like issues specific to the driver/HW).
644 * This flag must not be set for frames that don't request no-ack
645 * behaviour with IEEE80211_TX_CTL_NO_ACK.
647 * Note: If you have to add new flags to the enumeration, then don't
648 * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
650 enum mac80211_tx_info_flags {
651 IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
652 IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1),
653 IEEE80211_TX_CTL_NO_ACK = BIT(2),
654 IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3),
655 IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4),
656 IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5),
657 IEEE80211_TX_CTL_AMPDU = BIT(6),
658 IEEE80211_TX_CTL_INJECTED = BIT(7),
659 IEEE80211_TX_STAT_TX_FILTERED = BIT(8),
660 IEEE80211_TX_STAT_ACK = BIT(9),
661 IEEE80211_TX_STAT_AMPDU = BIT(10),
662 IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11),
663 IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12),
664 IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13),
665 IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14),
666 IEEE80211_TX_INTFL_RETRIED = BIT(15),
667 IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16),
668 IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17),
669 IEEE80211_TX_CTL_MORE_FRAMES = BIT(18),
670 IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19),
671 IEEE80211_TX_INTFL_MLME_CONN_TX = BIT(20),
672 IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21),
673 IEEE80211_TX_CTL_LDPC = BIT(22),
674 IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24),
675 IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25),
676 IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26),
677 IEEE80211_TX_CTL_NO_CCK_RATE = BIT(27),
678 IEEE80211_TX_STATUS_EOSP = BIT(28),
679 IEEE80211_TX_CTL_USE_MINRATE = BIT(29),
680 IEEE80211_TX_CTL_DONTFRAG = BIT(30),
681 IEEE80211_TX_STAT_NOACK_TRANSMITTED = BIT(31),
684 #define IEEE80211_TX_CTL_STBC_SHIFT 23
687 * enum mac80211_tx_control_flags - flags to describe transmit control
689 * @IEEE80211_TX_CTRL_PORT_CTRL_PROTO: this frame is a port control
690 * protocol frame (e.g. EAP)
691 * @IEEE80211_TX_CTRL_PS_RESPONSE: This frame is a response to a poll
692 * frame (PS-Poll or uAPSD).
694 * These flags are used in tx_info->control.flags.
696 enum mac80211_tx_control_flags {
697 IEEE80211_TX_CTRL_PORT_CTRL_PROTO = BIT(0),
698 IEEE80211_TX_CTRL_PS_RESPONSE = BIT(1),
702 * This definition is used as a mask to clear all temporary flags, which are
703 * set by the tx handlers for each transmission attempt by the mac80211 stack.
705 #define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \
706 IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \
707 IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \
708 IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \
709 IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \
710 IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER | \
711 IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \
712 IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP)
715 * enum mac80211_rate_control_flags - per-rate flags set by the
716 * Rate Control algorithm.
718 * These flags are set by the Rate control algorithm for each rate during tx,
719 * in the @flags member of struct ieee80211_tx_rate.
721 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
722 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
723 * This is set if the current BSS requires ERP protection.
724 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
725 * @IEEE80211_TX_RC_MCS: HT rate.
726 * @IEEE80211_TX_RC_VHT_MCS: VHT MCS rate, in this case the idx field is split
727 * into a higher 4 bits (Nss) and lower 4 bits (MCS number)
728 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
730 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
731 * @IEEE80211_TX_RC_80_MHZ_WIDTH: Indicates 80 MHz transmission
732 * @IEEE80211_TX_RC_160_MHZ_WIDTH: Indicates 160 MHz transmission
733 * (80+80 isn't supported yet)
734 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
735 * adjacent 20 MHz channels, if the current channel type is
736 * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
737 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
739 enum mac80211_rate_control_flags {
740 IEEE80211_TX_RC_USE_RTS_CTS = BIT(0),
741 IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1),
742 IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2),
744 /* rate index is an HT/VHT MCS instead of an index */
745 IEEE80211_TX_RC_MCS = BIT(3),
746 IEEE80211_TX_RC_GREEN_FIELD = BIT(4),
747 IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5),
748 IEEE80211_TX_RC_DUP_DATA = BIT(6),
749 IEEE80211_TX_RC_SHORT_GI = BIT(7),
750 IEEE80211_TX_RC_VHT_MCS = BIT(8),
751 IEEE80211_TX_RC_80_MHZ_WIDTH = BIT(9),
752 IEEE80211_TX_RC_160_MHZ_WIDTH = BIT(10),
756 /* there are 40 bytes if you don't need the rateset to be kept */
757 #define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
759 /* if you do need the rateset, then you have less space */
760 #define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
762 /* maximum number of rate stages */
763 #define IEEE80211_TX_MAX_RATES 4
765 /* maximum number of rate table entries */
766 #define IEEE80211_TX_RATE_TABLE_SIZE 4
769 * struct ieee80211_tx_rate - rate selection/status
771 * @idx: rate index to attempt to send with
772 * @flags: rate control flags (&enum mac80211_rate_control_flags)
773 * @count: number of tries in this rate before going to the next rate
775 * A value of -1 for @idx indicates an invalid rate and, if used
776 * in an array of retry rates, that no more rates should be tried.
778 * When used for transmit status reporting, the driver should
779 * always report the rate along with the flags it used.
781 * &struct ieee80211_tx_info contains an array of these structs
782 * in the control information, and it will be filled by the rate
783 * control algorithm according to what should be sent. For example,
784 * if this array contains, in the format { <idx>, <count> } the
786 * { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
787 * then this means that the frame should be transmitted
788 * up to twice at rate 3, up to twice at rate 2, and up to four
789 * times at rate 1 if it doesn't get acknowledged. Say it gets
790 * acknowledged by the peer after the fifth attempt, the status
791 * information should then contain
792 * { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
793 * since it was transmitted twice at rate 3, twice at rate 2
794 * and once at rate 1 after which we received an acknowledgement.
796 struct ieee80211_tx_rate {
802 #define IEEE80211_MAX_TX_RETRY 31
804 static inline void ieee80211_rate_set_vht(struct ieee80211_tx_rate *rate,
808 WARN_ON((nss - 1) & ~0x7);
809 rate->idx = ((nss - 1) << 4) | mcs;
813 ieee80211_rate_get_vht_mcs(const struct ieee80211_tx_rate *rate)
815 return rate->idx & 0xF;
819 ieee80211_rate_get_vht_nss(const struct ieee80211_tx_rate *rate)
821 return (rate->idx >> 4) + 1;
825 * struct ieee80211_tx_info - skb transmit information
827 * This structure is placed in skb->cb for three uses:
828 * (1) mac80211 TX control - mac80211 tells the driver what to do
829 * (2) driver internal use (if applicable)
830 * (3) TX status information - driver tells mac80211 what happened
832 * @flags: transmit info flags, defined above
833 * @band: the band to transmit on (use for checking for races)
834 * @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC
835 * @ack_frame_id: internal frame ID for TX status, used internally
836 * @control: union for control data
837 * @status: union for status data
838 * @driver_data: array of driver_data pointers
839 * @ampdu_ack_len: number of acked aggregated frames.
840 * relevant only if IEEE80211_TX_STAT_AMPDU was set.
841 * @ampdu_len: number of aggregated frames.
842 * relevant only if IEEE80211_TX_STAT_AMPDU was set.
843 * @ack_signal: signal strength of the ACK frame
845 struct ieee80211_tx_info {
846 /* common information */
859 struct ieee80211_tx_rate rates[
860 IEEE80211_TX_MAX_RATES];
868 /* only needed before rate control */
869 unsigned long jiffies;
871 /* NB: vif can be NULL for injected frames */
872 struct ieee80211_vif *vif;
873 struct ieee80211_key_conf *hw_key;
878 struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
884 void *status_driver_data[19 / sizeof(void *)];
887 struct ieee80211_tx_rate driver_rates[
888 IEEE80211_TX_MAX_RATES];
891 void *rate_driver_data[
892 IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
895 IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
900 * struct ieee80211_scan_ies - descriptors for different blocks of IEs
902 * This structure is used to point to different blocks of IEs in HW scan
903 * and scheduled scan. These blocks contain the IEs passed by userspace
904 * and the ones generated by mac80211.
906 * @ies: pointers to band specific IEs.
907 * @len: lengths of band_specific IEs.
908 * @common_ies: IEs for all bands (especially vendor specific ones)
909 * @common_ie_len: length of the common_ies
911 struct ieee80211_scan_ies {
912 const u8 *ies[IEEE80211_NUM_BANDS];
913 size_t len[IEEE80211_NUM_BANDS];
914 const u8 *common_ies;
915 size_t common_ie_len;
919 static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
921 return (struct ieee80211_tx_info *)skb->cb;
924 static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
926 return (struct ieee80211_rx_status *)skb->cb;
930 * ieee80211_tx_info_clear_status - clear TX status
932 * @info: The &struct ieee80211_tx_info to be cleared.
934 * When the driver passes an skb back to mac80211, it must report
935 * a number of things in TX status. This function clears everything
936 * in the TX status but the rate control information (it does clear
937 * the count since you need to fill that in anyway).
939 * NOTE: You can only use this function if you do NOT use
940 * info->driver_data! Use info->rate_driver_data
941 * instead if you need only the less space that allows.
944 ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
948 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
949 offsetof(struct ieee80211_tx_info, control.rates));
950 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
951 offsetof(struct ieee80211_tx_info, driver_rates));
952 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
953 /* clear the rate counts */
954 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
955 info->status.rates[i].count = 0;
958 offsetof(struct ieee80211_tx_info, status.ack_signal) != 20);
959 memset(&info->status.ampdu_ack_len, 0,
960 sizeof(struct ieee80211_tx_info) -
961 offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
966 * enum mac80211_rx_flags - receive flags
968 * These flags are used with the @flag member of &struct ieee80211_rx_status.
969 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
970 * Use together with %RX_FLAG_MMIC_STRIPPED.
971 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
972 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
973 * verification has been done by the hardware.
974 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
975 * If this flag is set, the stack cannot do any replay detection
976 * hence the driver or hardware will have to do that.
977 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
979 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
981 * @RX_FLAG_MACTIME_START: The timestamp passed in the RX status (@mactime
982 * field) is valid and contains the time the first symbol of the MPDU
983 * was received. This is useful in monitor mode and for proper IBSS
985 * @RX_FLAG_MACTIME_END: The timestamp passed in the RX status (@mactime
986 * field) is valid and contains the time the last symbol of the MPDU
987 * (including FCS) was received.
988 * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
989 * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
990 * @RX_FLAG_VHT: VHT MCS was used and rate_index is MCS index
991 * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
992 * @RX_FLAG_SHORT_GI: Short guard interval was used
993 * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present.
994 * Valid only for data frames (mainly A-MPDU)
995 * @RX_FLAG_HT_GF: This frame was received in a HT-greenfield transmission, if
996 * the driver fills this value it should add %IEEE80211_RADIOTAP_MCS_HAVE_FMT
997 * to hw.radiotap_mcs_details to advertise that fact
998 * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference
999 * number (@ampdu_reference) must be populated and be a distinct number for
1001 * @RX_FLAG_AMPDU_REPORT_ZEROLEN: driver reports 0-length subframes
1002 * @RX_FLAG_AMPDU_IS_ZEROLEN: This is a zero-length subframe, for
1003 * monitoring purposes only
1004 * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all
1005 * subframes of a single A-MPDU
1006 * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU
1007 * @RX_FLAG_AMPDU_DELIM_CRC_ERROR: A delimiter CRC error has been detected
1009 * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC
1010 * is stored in the @ampdu_delimiter_crc field)
1011 * @RX_FLAG_LDPC: LDPC was used
1012 * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
1013 * @RX_FLAG_10MHZ: 10 MHz (half channel) was used
1014 * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used
1015 * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU
1016 * subframes instead of a one huge frame for performance reasons.
1017 * All, but the last MSDU from an A-MSDU should have this flag set. E.g.
1018 * if an A-MSDU has 3 frames, the first 2 must have the flag set, while
1019 * the 3rd (last) one must not have this flag set. The flag is used to
1020 * deal with retransmission/duplication recovery properly since A-MSDU
1021 * subframes share the same sequence number. Reported subframes can be
1022 * either regular MSDU or singly A-MSDUs. Subframes must not be
1023 * interleaved with other frames.
1024 * @RX_FLAG_RADIOTAP_VENDOR_DATA: This frame contains vendor-specific
1025 * radiotap data in the skb->data (before the frame) as described by
1026 * the &struct ieee80211_vendor_radiotap.
1028 enum mac80211_rx_flags {
1029 RX_FLAG_MMIC_ERROR = BIT(0),
1030 RX_FLAG_DECRYPTED = BIT(1),
1031 RX_FLAG_MMIC_STRIPPED = BIT(3),
1032 RX_FLAG_IV_STRIPPED = BIT(4),
1033 RX_FLAG_FAILED_FCS_CRC = BIT(5),
1034 RX_FLAG_FAILED_PLCP_CRC = BIT(6),
1035 RX_FLAG_MACTIME_START = BIT(7),
1036 RX_FLAG_SHORTPRE = BIT(8),
1037 RX_FLAG_HT = BIT(9),
1038 RX_FLAG_40MHZ = BIT(10),
1039 RX_FLAG_SHORT_GI = BIT(11),
1040 RX_FLAG_NO_SIGNAL_VAL = BIT(12),
1041 RX_FLAG_HT_GF = BIT(13),
1042 RX_FLAG_AMPDU_DETAILS = BIT(14),
1043 RX_FLAG_AMPDU_REPORT_ZEROLEN = BIT(15),
1044 RX_FLAG_AMPDU_IS_ZEROLEN = BIT(16),
1045 RX_FLAG_AMPDU_LAST_KNOWN = BIT(17),
1046 RX_FLAG_AMPDU_IS_LAST = BIT(18),
1047 RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(19),
1048 RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(20),
1049 RX_FLAG_MACTIME_END = BIT(21),
1050 RX_FLAG_VHT = BIT(22),
1051 RX_FLAG_LDPC = BIT(23),
1052 RX_FLAG_STBC_MASK = BIT(26) | BIT(27),
1053 RX_FLAG_10MHZ = BIT(28),
1054 RX_FLAG_5MHZ = BIT(29),
1055 RX_FLAG_AMSDU_MORE = BIT(30),
1056 RX_FLAG_RADIOTAP_VENDOR_DATA = BIT(31),
1059 #define RX_FLAG_STBC_SHIFT 26
1062 * enum mac80211_rx_vht_flags - receive VHT flags
1064 * These flags are used with the @vht_flag member of
1065 * &struct ieee80211_rx_status.
1066 * @RX_VHT_FLAG_80MHZ: 80 MHz was used
1067 * @RX_VHT_FLAG_160MHZ: 160 MHz was used
1068 * @RX_VHT_FLAG_BF: packet was beamformed
1070 enum mac80211_rx_vht_flags {
1071 RX_VHT_FLAG_80MHZ = BIT(0),
1072 RX_VHT_FLAG_160MHZ = BIT(1),
1073 RX_VHT_FLAG_BF = BIT(2),
1077 * struct ieee80211_rx_status - receive status
1079 * The low-level driver should provide this information (the subset
1080 * supported by hardware) to the 802.11 code with each received
1081 * frame, in the skb's control buffer (cb).
1083 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
1084 * (TSF) timer when the first data symbol (MPDU) arrived at the hardware.
1085 * @device_timestamp: arbitrary timestamp for the device, mac80211 doesn't use
1086 * it but can store it and pass it back to the driver for synchronisation
1087 * @band: the active band when this frame was received
1088 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
1089 * @signal: signal strength when receiving this frame, either in dBm, in dB or
1090 * unspecified depending on the hardware capabilities flags
1091 * @IEEE80211_HW_SIGNAL_*
1092 * @chains: bitmask of receive chains for which separate signal strength
1093 * values were filled.
1094 * @chain_signal: per-chain signal strength, in dBm (unlike @signal, doesn't
1095 * support dB or unspecified units)
1096 * @antenna: antenna used
1097 * @rate_idx: index of data rate into band's supported rates or MCS index if
1098 * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT)
1099 * @vht_nss: number of streams (VHT only)
1101 * @vht_flag: %RX_VHT_FLAG_*
1102 * @rx_flags: internal RX flags for mac80211
1103 * @ampdu_reference: A-MPDU reference number, must be a different value for
1104 * each A-MPDU but the same for each subframe within one A-MPDU
1105 * @ampdu_delimiter_crc: A-MPDU delimiter CRC
1107 struct ieee80211_rx_status {
1109 u32 device_timestamp;
1110 u32 ampdu_reference;
1121 s8 chain_signal[IEEE80211_MAX_CHAINS];
1122 u8 ampdu_delimiter_crc;
1126 * struct ieee80211_vendor_radiotap - vendor radiotap data information
1127 * @present: presence bitmap for this vendor namespace
1128 * (this could be extended in the future if any vendor needs more
1129 * bits, the radiotap spec does allow for that)
1130 * @align: radiotap vendor namespace alignment. This defines the needed
1131 * alignment for the @data field below, not for the vendor namespace
1132 * description itself (which has a fixed 2-byte alignment)
1133 * Must be a power of two, and be set to at least 1!
1134 * @oui: radiotap vendor namespace OUI
1135 * @subns: radiotap vendor sub namespace
1136 * @len: radiotap vendor sub namespace skip length, if alignment is done
1137 * then that's added to this, i.e. this is only the length of the
1139 * @pad: number of bytes of padding after the @data, this exists so that
1140 * the skb data alignment can be preserved even if the data has odd
1142 * @data: the actual vendor namespace data
1144 * This struct, including the vendor data, goes into the skb->data before
1145 * the 802.11 header. It's split up in mac80211 using the align/oui/subns
1148 struct ieee80211_vendor_radiotap {
1159 * enum ieee80211_conf_flags - configuration flags
1161 * Flags to define PHY configuration options
1163 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
1164 * to determine for example whether to calculate timestamps for packets
1165 * or not, do not use instead of filter flags!
1166 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
1167 * This is the power save mode defined by IEEE 802.11-2007 section 11.2,
1168 * meaning that the hardware still wakes up for beacons, is able to
1169 * transmit frames and receive the possible acknowledgment frames.
1170 * Not to be confused with hardware specific wakeup/sleep states,
1171 * driver is responsible for that. See the section "Powersave support"
1173 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
1174 * the driver should be prepared to handle configuration requests but
1175 * may turn the device off as much as possible. Typically, this flag will
1176 * be set when an interface is set UP but not associated or scanning, but
1177 * it can also be unset in that case when monitor interfaces are active.
1178 * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main
1179 * operating channel.
1181 enum ieee80211_conf_flags {
1182 IEEE80211_CONF_MONITOR = (1<<0),
1183 IEEE80211_CONF_PS = (1<<1),
1184 IEEE80211_CONF_IDLE = (1<<2),
1185 IEEE80211_CONF_OFFCHANNEL = (1<<3),
1190 * enum ieee80211_conf_changed - denotes which configuration changed
1192 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
1193 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
1194 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
1195 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
1196 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
1197 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
1198 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
1199 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
1200 * Note that this is only valid if channel contexts are not used,
1201 * otherwise each channel context has the number of chains listed.
1203 enum ieee80211_conf_changed {
1204 IEEE80211_CONF_CHANGE_SMPS = BIT(1),
1205 IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2),
1206 IEEE80211_CONF_CHANGE_MONITOR = BIT(3),
1207 IEEE80211_CONF_CHANGE_PS = BIT(4),
1208 IEEE80211_CONF_CHANGE_POWER = BIT(5),
1209 IEEE80211_CONF_CHANGE_CHANNEL = BIT(6),
1210 IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7),
1211 IEEE80211_CONF_CHANGE_IDLE = BIT(8),
1215 * enum ieee80211_smps_mode - spatial multiplexing power save mode
1217 * @IEEE80211_SMPS_AUTOMATIC: automatic
1218 * @IEEE80211_SMPS_OFF: off
1219 * @IEEE80211_SMPS_STATIC: static
1220 * @IEEE80211_SMPS_DYNAMIC: dynamic
1221 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
1223 enum ieee80211_smps_mode {
1224 IEEE80211_SMPS_AUTOMATIC,
1226 IEEE80211_SMPS_STATIC,
1227 IEEE80211_SMPS_DYNAMIC,
1230 IEEE80211_SMPS_NUM_MODES,
1234 * struct ieee80211_conf - configuration of the device
1236 * This struct indicates how the driver shall configure the hardware.
1238 * @flags: configuration flags defined above
1240 * @listen_interval: listen interval in units of beacon interval
1241 * @max_sleep_period: the maximum number of beacon intervals to sleep for
1242 * before checking the beacon for a TIM bit (managed mode only); this
1243 * value will be only achievable between DTIM frames, the hardware
1244 * needs to check for the multicast traffic bit in DTIM beacons.
1245 * This variable is valid only when the CONF_PS flag is set.
1246 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
1247 * in power saving. Power saving will not be enabled until a beacon
1248 * has been received and the DTIM period is known.
1249 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
1250 * powersave documentation below. This variable is valid only when
1251 * the CONF_PS flag is set.
1253 * @power_level: requested transmit power (in dBm), backward compatibility
1254 * value only that is set to the minimum of all interfaces
1256 * @chandef: the channel definition to tune to
1257 * @radar_enabled: whether radar detection is enabled
1259 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
1260 * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
1261 * but actually means the number of transmissions not the number of retries
1262 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
1263 * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
1264 * number of transmissions not the number of retries
1266 * @smps_mode: spatial multiplexing powersave mode; note that
1267 * %IEEE80211_SMPS_STATIC is used when the device is not
1268 * configured for an HT channel.
1269 * Note that this is only valid if channel contexts are not used,
1270 * otherwise each channel context has the number of chains listed.
1272 struct ieee80211_conf {
1274 int power_level, dynamic_ps_timeout;
1275 int max_sleep_period;
1277 u16 listen_interval;
1280 u8 long_frame_max_tx_count, short_frame_max_tx_count;
1282 struct cfg80211_chan_def chandef;
1284 enum ieee80211_smps_mode smps_mode;
1288 * struct ieee80211_channel_switch - holds the channel switch data
1290 * The information provided in this structure is required for channel switch
1293 * @timestamp: value in microseconds of the 64-bit Time Synchronization
1294 * Function (TSF) timer when the frame containing the channel switch
1295 * announcement was received. This is simply the rx.mactime parameter
1296 * the driver passed into mac80211.
1297 * @device_timestamp: arbitrary timestamp for the device, this is the
1298 * rx.device_timestamp parameter the driver passed to mac80211.
1299 * @block_tx: Indicates whether transmission must be blocked before the
1300 * scheduled channel switch, as indicated by the AP.
1301 * @chandef: the new channel to switch to
1302 * @count: the number of TBTT's until the channel switch event
1304 struct ieee80211_channel_switch {
1306 u32 device_timestamp;
1308 struct cfg80211_chan_def chandef;
1313 * enum ieee80211_vif_flags - virtual interface flags
1315 * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering
1316 * on this virtual interface to avoid unnecessary CPU wakeups
1317 * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality
1318 * monitoring on this virtual interface -- i.e. it can monitor
1319 * connection quality related parameters, such as the RSSI level and
1320 * provide notifications if configured trigger levels are reached.
1321 * @IEEE80211_VIF_SUPPORTS_UAPSD: The device can do U-APSD for this
1322 * interface. This flag should be set during interface addition,
1323 * but may be set/cleared as late as authentication to an AP. It is
1324 * only valid for managed/station mode interfaces.
1326 enum ieee80211_vif_flags {
1327 IEEE80211_VIF_BEACON_FILTER = BIT(0),
1328 IEEE80211_VIF_SUPPORTS_CQM_RSSI = BIT(1),
1329 IEEE80211_VIF_SUPPORTS_UAPSD = BIT(2),
1333 * struct ieee80211_vif - per-interface data
1335 * Data in this structure is continually present for driver
1336 * use during the life of a virtual interface.
1338 * @type: type of this virtual interface
1339 * @bss_conf: BSS configuration for this interface, either our own
1340 * or the BSS we're associated to
1341 * @addr: address of this interface
1342 * @p2p: indicates whether this AP or STA interface is a p2p
1343 * interface, i.e. a GO or p2p-sta respectively
1344 * @csa_active: marks whether a channel switch is going on. Internally it is
1345 * write-protected by sdata_lock and local->mtx so holding either is fine
1347 * @driver_flags: flags/capabilities the driver has for this interface,
1348 * these need to be set (or cleared) when the interface is added
1349 * or, if supported by the driver, the interface type is changed
1350 * at runtime, mac80211 will never touch this field
1351 * @hw_queue: hardware queue for each AC
1352 * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only
1353 * @chanctx_conf: The channel context this interface is assigned to, or %NULL
1354 * when it is not assigned. This pointer is RCU-protected due to the TX
1355 * path needing to access it; even though the netdev carrier will always
1356 * be off when it is %NULL there can still be races and packets could be
1357 * processed after it switches back to %NULL.
1358 * @debugfs_dir: debugfs dentry, can be used by drivers to create own per
1359 * interface debug files. Note that it will be NULL for the virtual
1360 * monitor interface (if that is requested.)
1361 * @drv_priv: data area for driver use, will always be aligned to
1363 * @txq: the multicast data TX queue (if driver uses the TXQ abstraction)
1365 struct ieee80211_vif {
1366 enum nl80211_iftype type;
1367 struct ieee80211_bss_conf bss_conf;
1373 u8 hw_queue[IEEE80211_NUM_ACS];
1375 struct ieee80211_txq *txq;
1377 struct ieee80211_chanctx_conf __rcu *chanctx_conf;
1381 #ifdef CONFIG_MAC80211_DEBUGFS
1382 struct dentry *debugfs_dir;
1386 u8 drv_priv[0] __aligned(sizeof(void *));
1389 static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
1391 #ifdef CONFIG_MAC80211_MESH
1392 return vif->type == NL80211_IFTYPE_MESH_POINT;
1398 * wdev_to_ieee80211_vif - return a vif struct from a wdev
1399 * @wdev: the wdev to get the vif for
1401 * This can be used by mac80211 drivers with direct cfg80211 APIs
1402 * (like the vendor commands) that get a wdev.
1404 * Note that this function may return %NULL if the given wdev isn't
1405 * associated with a vif that the driver knows about (e.g. monitor
1406 * or AP_VLAN interfaces.)
1408 struct ieee80211_vif *wdev_to_ieee80211_vif(struct wireless_dev *wdev);
1411 * ieee80211_vif_to_wdev - return a wdev struct from a vif
1412 * @vif: the vif to get the wdev for
1414 * This can be used by mac80211 drivers with direct cfg80211 APIs
1415 * (like the vendor commands) that needs to get the wdev for a vif.
1417 * Note that this function may return %NULL if the given wdev isn't
1418 * associated with a vif that the driver knows about (e.g. monitor
1419 * or AP_VLAN interfaces.)
1421 struct wireless_dev *ieee80211_vif_to_wdev(struct ieee80211_vif *vif);
1424 * enum ieee80211_key_flags - key flags
1426 * These flags are used for communication about keys between the driver
1427 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
1429 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
1430 * driver to indicate that it requires IV generation for this
1431 * particular key. Setting this flag does not necessarily mean that SKBs
1432 * will have sufficient tailroom for ICV or MIC.
1433 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
1434 * the driver for a TKIP key if it requires Michael MIC
1435 * generation in software.
1436 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
1437 * that the key is pairwise rather then a shared key.
1438 * @IEEE80211_KEY_FLAG_SW_MGMT_TX: This flag should be set by the driver for a
1439 * CCMP/GCMP key if it requires CCMP/GCMP encryption of management frames
1440 * (MFP) to be done in software.
1441 * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver
1442 * if space should be prepared for the IV, but the IV
1443 * itself should not be generated. Do not set together with
1444 * @IEEE80211_KEY_FLAG_GENERATE_IV on the same key. Setting this flag does
1445 * not necessarily mean that SKBs will have sufficient tailroom for ICV or
1447 * @IEEE80211_KEY_FLAG_RX_MGMT: This key will be used to decrypt received
1448 * management frames. The flag can help drivers that have a hardware
1449 * crypto implementation that doesn't deal with management frames
1450 * properly by allowing them to not upload the keys to hardware and
1451 * fall back to software crypto. Note that this flag deals only with
1452 * RX, if your crypto engine can't deal with TX you can also set the
1453 * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW.
1454 * @IEEE80211_KEY_FLAG_GENERATE_IV_MGMT: This flag should be set by the
1455 * driver for a CCMP/GCMP key to indicate that is requires IV generation
1456 * only for managment frames (MFP).
1457 * @IEEE80211_KEY_FLAG_RESERVE_TAILROOM: This flag should be set by the
1458 * driver for a key to indicate that sufficient tailroom must always
1459 * be reserved for ICV or MIC, even when HW encryption is enabled.
1461 enum ieee80211_key_flags {
1462 IEEE80211_KEY_FLAG_GENERATE_IV_MGMT = BIT(0),
1463 IEEE80211_KEY_FLAG_GENERATE_IV = BIT(1),
1464 IEEE80211_KEY_FLAG_GENERATE_MMIC = BIT(2),
1465 IEEE80211_KEY_FLAG_PAIRWISE = BIT(3),
1466 IEEE80211_KEY_FLAG_SW_MGMT_TX = BIT(4),
1467 IEEE80211_KEY_FLAG_PUT_IV_SPACE = BIT(5),
1468 IEEE80211_KEY_FLAG_RX_MGMT = BIT(6),
1469 IEEE80211_KEY_FLAG_RESERVE_TAILROOM = BIT(7),
1473 * struct ieee80211_key_conf - key information
1475 * This key information is given by mac80211 to the driver by
1476 * the set_key() callback in &struct ieee80211_ops.
1478 * @hw_key_idx: To be set by the driver, this is the key index the driver
1479 * wants to be given when a frame is transmitted and needs to be
1480 * encrypted in hardware.
1481 * @cipher: The key's cipher suite selector.
1482 * @flags: key flags, see &enum ieee80211_key_flags.
1483 * @keyidx: the key index (0-3)
1484 * @keylen: key material length
1485 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
1487 * - Temporal Encryption Key (128 bits)
1488 * - Temporal Authenticator Tx MIC Key (64 bits)
1489 * - Temporal Authenticator Rx MIC Key (64 bits)
1490 * @icv_len: The ICV length for this key type
1491 * @iv_len: The IV length for this key type
1493 struct ieee80211_key_conf {
1504 #define IEEE80211_MAX_PN_LEN 16
1507 * struct ieee80211_key_seq - key sequence counter
1509 * @tkip: TKIP data, containing IV32 and IV16 in host byte order
1510 * @ccmp: PN data, most significant byte first (big endian,
1511 * reverse order than in packet)
1512 * @aes_cmac: PN data, most significant byte first (big endian,
1513 * reverse order than in packet)
1514 * @aes_gmac: PN data, most significant byte first (big endian,
1515 * reverse order than in packet)
1516 * @gcmp: PN data, most significant byte first (big endian,
1517 * reverse order than in packet)
1518 * @hw: data for HW-only (e.g. cipher scheme) keys
1520 struct ieee80211_key_seq {
1539 u8 seq[IEEE80211_MAX_PN_LEN];
1546 * struct ieee80211_cipher_scheme - cipher scheme
1548 * This structure contains a cipher scheme information defining
1549 * the secure packet crypto handling.
1551 * @cipher: a cipher suite selector
1552 * @iftype: a cipher iftype bit mask indicating an allowed cipher usage
1553 * @hdr_len: a length of a security header used the cipher
1554 * @pn_len: a length of a packet number in the security header
1555 * @pn_off: an offset of pn from the beginning of the security header
1556 * @key_idx_off: an offset of key index byte in the security header
1557 * @key_idx_mask: a bit mask of key_idx bits
1558 * @key_idx_shift: a bit shift needed to get key_idx
1559 * key_idx value calculation:
1560 * (sec_header_base[key_idx_off] & key_idx_mask) >> key_idx_shift
1561 * @mic_len: a mic length in bytes
1563 struct ieee80211_cipher_scheme {
1576 * enum set_key_cmd - key command
1578 * Used with the set_key() callback in &struct ieee80211_ops, this
1579 * indicates whether a key is being removed or added.
1581 * @SET_KEY: a key is set
1582 * @DISABLE_KEY: a key must be disabled
1585 SET_KEY, DISABLE_KEY,
1589 * enum ieee80211_sta_state - station state
1591 * @IEEE80211_STA_NOTEXIST: station doesn't exist at all,
1592 * this is a special state for add/remove transitions
1593 * @IEEE80211_STA_NONE: station exists without special state
1594 * @IEEE80211_STA_AUTH: station is authenticated
1595 * @IEEE80211_STA_ASSOC: station is associated
1596 * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X)
1598 enum ieee80211_sta_state {
1599 /* NOTE: These need to be ordered correctly! */
1600 IEEE80211_STA_NOTEXIST,
1603 IEEE80211_STA_ASSOC,
1604 IEEE80211_STA_AUTHORIZED,
1608 * enum ieee80211_sta_rx_bandwidth - station RX bandwidth
1609 * @IEEE80211_STA_RX_BW_20: station can only receive 20 MHz
1610 * @IEEE80211_STA_RX_BW_40: station can receive up to 40 MHz
1611 * @IEEE80211_STA_RX_BW_80: station can receive up to 80 MHz
1612 * @IEEE80211_STA_RX_BW_160: station can receive up to 160 MHz
1613 * (including 80+80 MHz)
1615 * Implementation note: 20 must be zero to be initialized
1616 * correctly, the values must be sorted.
1618 enum ieee80211_sta_rx_bandwidth {
1619 IEEE80211_STA_RX_BW_20 = 0,
1620 IEEE80211_STA_RX_BW_40,
1621 IEEE80211_STA_RX_BW_80,
1622 IEEE80211_STA_RX_BW_160,
1626 * struct ieee80211_sta_rates - station rate selection table
1628 * @rcu_head: RCU head used for freeing the table on update
1629 * @rate: transmit rates/flags to be used by default.
1630 * Overriding entries per-packet is possible by using cb tx control.
1632 struct ieee80211_sta_rates {
1633 struct rcu_head rcu_head;
1640 } rate[IEEE80211_TX_RATE_TABLE_SIZE];
1644 * struct ieee80211_sta - station table entry
1646 * A station table entry represents a station we are possibly
1647 * communicating with. Since stations are RCU-managed in
1648 * mac80211, any ieee80211_sta pointer you get access to must
1649 * either be protected by rcu_read_lock() explicitly or implicitly,
1650 * or you must take good care to not use such a pointer after a
1651 * call to your sta_remove callback that removed it.
1653 * @addr: MAC address
1654 * @aid: AID we assigned to the station if we're an AP
1655 * @supp_rates: Bitmap of supported rates (per band)
1656 * @ht_cap: HT capabilities of this STA; restricted to our own capabilities
1657 * @vht_cap: VHT capabilities of this STA; restricted to our own capabilities
1658 * @wme: indicates whether the STA supports QoS/WME (if local devices does,
1659 * otherwise always false)
1660 * @drv_priv: data area for driver use, will always be aligned to
1661 * sizeof(void *), size is determined in hw information.
1662 * @uapsd_queues: bitmap of queues configured for uapsd. Only valid
1663 * if wme is supported.
1664 * @max_sp: max Service Period. Only valid if wme is supported.
1665 * @bandwidth: current bandwidth the station can receive with
1666 * @rx_nss: in HT/VHT, the maximum number of spatial streams the
1667 * station can receive at the moment, changed by operating mode
1668 * notifications and capabilities. The value is only valid after
1669 * the station moves to associated state.
1670 * @smps_mode: current SMPS mode (off, static or dynamic)
1671 * @rates: rate control selection table
1672 * @tdls: indicates whether the STA is a TDLS peer
1673 * @tdls_initiator: indicates the STA is an initiator of the TDLS link. Only
1674 * valid if the STA is a TDLS peer in the first place.
1675 * @mfp: indicates whether the STA uses management frame protection or not.
1676 * @txq: per-TID data TX queues (if driver uses the TXQ abstraction)
1678 struct ieee80211_sta {
1679 u32 supp_rates[IEEE80211_NUM_BANDS];
1682 struct ieee80211_sta_ht_cap ht_cap;
1683 struct ieee80211_sta_vht_cap vht_cap;
1688 enum ieee80211_sta_rx_bandwidth bandwidth;
1689 enum ieee80211_smps_mode smps_mode;
1690 struct ieee80211_sta_rates __rcu *rates;
1692 bool tdls_initiator;
1695 struct ieee80211_txq *txq[IEEE80211_NUM_TIDS];
1698 u8 drv_priv[0] __aligned(sizeof(void *));
1702 * enum sta_notify_cmd - sta notify command
1704 * Used with the sta_notify() callback in &struct ieee80211_ops, this
1705 * indicates if an associated station made a power state transition.
1707 * @STA_NOTIFY_SLEEP: a station is now sleeping
1708 * @STA_NOTIFY_AWAKE: a sleeping station woke up
1710 enum sta_notify_cmd {
1711 STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
1715 * struct ieee80211_tx_control - TX control data
1717 * @sta: station table entry, this sta pointer may be NULL and
1718 * it is not allowed to copy the pointer, due to RCU.
1720 struct ieee80211_tx_control {
1721 struct ieee80211_sta *sta;
1725 * struct ieee80211_txq - Software intermediate tx queue
1727 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
1728 * @sta: station table entry, %NULL for per-vif queue
1729 * @tid: the TID for this queue (unused for per-vif queue)
1730 * @ac: the AC for this queue
1731 * @drv_priv: data area for driver use, will always be aligned to
1734 * The driver can obtain packets from this queue by calling
1735 * ieee80211_tx_dequeue().
1737 struct ieee80211_txq {
1738 struct ieee80211_vif *vif;
1739 struct ieee80211_sta *sta;
1744 u8 drv_priv[0] __aligned(sizeof(void *));
1748 * enum ieee80211_hw_flags - hardware flags
1750 * These flags are used to indicate hardware capabilities to
1751 * the stack. Generally, flags here should have their meaning
1752 * done in a way that the simplest hardware doesn't need setting
1753 * any particular flags. There are some exceptions to this rule,
1754 * however, so you are advised to review these flags carefully.
1756 * @IEEE80211_HW_HAS_RATE_CONTROL:
1757 * The hardware or firmware includes rate control, and cannot be
1758 * controlled by the stack. As such, no rate control algorithm
1759 * should be instantiated, and the TX rate reported to userspace
1760 * will be taken from the TX status instead of the rate control
1762 * Note that this requires that the driver implement a number of
1763 * callbacks so it has the correct information, it needs to have
1764 * the @set_rts_threshold callback and must look at the BSS config
1765 * @use_cts_prot for G/N protection, @use_short_slot for slot
1766 * timing in 2.4 GHz and @use_short_preamble for preambles for
1769 * @IEEE80211_HW_RX_INCLUDES_FCS:
1770 * Indicates that received frames passed to the stack include
1771 * the FCS at the end.
1773 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
1774 * Some wireless LAN chipsets buffer broadcast/multicast frames
1775 * for power saving stations in the hardware/firmware and others
1776 * rely on the host system for such buffering. This option is used
1777 * to configure the IEEE 802.11 upper layer to buffer broadcast and
1778 * multicast frames when there are power saving stations so that
1779 * the driver can fetch them with ieee80211_get_buffered_bc().
1781 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
1782 * Hardware is not capable of short slot operation on the 2.4 GHz band.
1784 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
1785 * Hardware is not capable of receiving frames with short preamble on
1788 * @IEEE80211_HW_SIGNAL_UNSPEC:
1789 * Hardware can provide signal values but we don't know its units. We
1790 * expect values between 0 and @max_signal.
1791 * If possible please provide dB or dBm instead.
1793 * @IEEE80211_HW_SIGNAL_DBM:
1794 * Hardware gives signal values in dBm, decibel difference from
1795 * one milliwatt. This is the preferred method since it is standardized
1796 * between different devices. @max_signal does not need to be set.
1798 * @IEEE80211_HW_SPECTRUM_MGMT:
1799 * Hardware supports spectrum management defined in 802.11h
1800 * Measurement, Channel Switch, Quieting, TPC
1802 * @IEEE80211_HW_AMPDU_AGGREGATION:
1803 * Hardware supports 11n A-MPDU aggregation.
1805 * @IEEE80211_HW_SUPPORTS_PS:
1806 * Hardware has power save support (i.e. can go to sleep).
1808 * @IEEE80211_HW_PS_NULLFUNC_STACK:
1809 * Hardware requires nullfunc frame handling in stack, implies
1810 * stack support for dynamic PS.
1812 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
1813 * Hardware has support for dynamic PS.
1815 * @IEEE80211_HW_MFP_CAPABLE:
1816 * Hardware supports management frame protection (MFP, IEEE 802.11w).
1818 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
1819 * Hardware can provide ack status reports of Tx frames to
1822 * @IEEE80211_HW_CONNECTION_MONITOR:
1823 * The hardware performs its own connection monitoring, including
1824 * periodic keep-alives to the AP and probing the AP on beacon loss.
1826 * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
1827 * This device needs to get data from beacon before association (i.e.
1830 * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports
1831 * per-station GTKs as used by IBSS RSN or during fast transition. If
1832 * the device doesn't support per-station GTKs, but can be asked not
1833 * to decrypt group addressed frames, then IBSS RSN support is still
1834 * possible but software crypto will be used. Advertise the wiphy flag
1835 * only in that case.
1837 * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device
1838 * autonomously manages the PS status of connected stations. When
1839 * this flag is set mac80211 will not trigger PS mode for connected
1840 * stations based on the PM bit of incoming frames.
1841 * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure
1842 * the PS mode of connected stations.
1844 * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session
1845 * setup strictly in HW. mac80211 should not attempt to do this in
1848 * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of
1849 * a virtual monitor interface when monitor interfaces are the only
1850 * active interfaces.
1852 * @IEEE80211_HW_NO_AUTO_VIF: The driver would like for no wlanX to
1853 * be created. It is expected user-space will create vifs as
1854 * desired (and thus have them named as desired).
1856 * @IEEE80211_HW_SW_CRYPTO_CONTROL: The driver wants to control which of the
1857 * crypto algorithms can be done in software - so don't automatically
1858 * try to fall back to it if hardware crypto fails, but do so only if
1859 * the driver returns 1. This also forces the driver to advertise its
1860 * supported cipher suites.
1862 * @IEEE80211_HW_SUPPORT_FAST_XMIT: The driver/hardware supports fast-xmit,
1863 * this currently requires only the ability to calculate the duration
1866 * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface
1867 * queue mapping in order to use different queues (not just one per AC)
1868 * for different virtual interfaces. See the doc section on HW queue
1869 * control for more details.
1871 * @IEEE80211_HW_SUPPORTS_RC_TABLE: The driver supports using a rate
1872 * selection table provided by the rate control algorithm.
1874 * @IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF: Use the P2P Device address for any
1875 * P2P Interface. This will be honoured even if more than one interface
1878 * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames
1879 * only, to allow getting TBTT of a DTIM beacon.
1881 * @IEEE80211_HW_SUPPORTS_HT_CCK_RATES: Hardware supports mixing HT/CCK rates
1882 * and can cope with CCK rates in an aggregation session (e.g. by not
1883 * using aggregation for such frames.)
1885 * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA)
1886 * for a single active channel while using channel contexts. When support
1887 * is not enabled the default action is to disconnect when getting the
1890 * @IEEE80211_HW_SUPPORTS_CLONED_SKBS: The driver will never modify the payload
1891 * or tailroom of TX skbs without copying them first.
1893 * @IEEE80211_SINGLE_HW_SCAN_ON_ALL_BANDS: The HW supports scanning on all bands
1894 * in one command, mac80211 doesn't have to run separate scans per band.
1896 enum ieee80211_hw_flags {
1897 IEEE80211_HW_HAS_RATE_CONTROL = 1<<0,
1898 IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
1899 IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
1900 IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
1901 IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
1902 IEEE80211_HW_SIGNAL_UNSPEC = 1<<5,
1903 IEEE80211_HW_SIGNAL_DBM = 1<<6,
1904 IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC = 1<<7,
1905 IEEE80211_HW_SPECTRUM_MGMT = 1<<8,
1906 IEEE80211_HW_AMPDU_AGGREGATION = 1<<9,
1907 IEEE80211_HW_SUPPORTS_PS = 1<<10,
1908 IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11,
1909 IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12,
1910 IEEE80211_HW_MFP_CAPABLE = 1<<13,
1911 IEEE80211_HW_WANT_MONITOR_VIF = 1<<14,
1912 IEEE80211_HW_NO_AUTO_VIF = 1<<15,
1913 IEEE80211_HW_SW_CRYPTO_CONTROL = 1<<16,
1914 IEEE80211_HW_SUPPORT_FAST_XMIT = 1<<17,
1915 IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18,
1916 IEEE80211_HW_CONNECTION_MONITOR = 1<<19,
1917 IEEE80211_HW_QUEUE_CONTROL = 1<<20,
1918 IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21,
1919 IEEE80211_HW_AP_LINK_PS = 1<<22,
1920 IEEE80211_HW_TX_AMPDU_SETUP_IN_HW = 1<<23,
1921 IEEE80211_HW_SUPPORTS_RC_TABLE = 1<<24,
1922 IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25,
1923 IEEE80211_HW_TIMING_BEACON_ONLY = 1<<26,
1924 IEEE80211_HW_SUPPORTS_HT_CCK_RATES = 1<<27,
1925 IEEE80211_HW_CHANCTX_STA_CSA = 1<<28,
1926 IEEE80211_HW_SUPPORTS_CLONED_SKBS = 1<<29,
1927 IEEE80211_SINGLE_HW_SCAN_ON_ALL_BANDS = 1<<30,
1931 * struct ieee80211_hw - hardware information and state
1933 * This structure contains the configuration and hardware
1934 * information for an 802.11 PHY.
1936 * @wiphy: This points to the &struct wiphy allocated for this
1937 * 802.11 PHY. You must fill in the @perm_addr and @dev
1938 * members of this structure using SET_IEEE80211_DEV()
1939 * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
1940 * bands (with channels, bitrates) are registered here.
1942 * @conf: &struct ieee80211_conf, device configuration, don't use.
1944 * @priv: pointer to private area that was allocated for driver use
1945 * along with this structure.
1947 * @flags: hardware flags, see &enum ieee80211_hw_flags.
1949 * @extra_tx_headroom: headroom to reserve in each transmit skb
1950 * for use by the driver (e.g. for transmit headers.)
1952 * @extra_beacon_tailroom: tailroom to reserve in each beacon tx skb.
1953 * Can be used by drivers to add extra IEs.
1955 * @max_signal: Maximum value for signal (rssi) in RX information, used
1956 * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
1958 * @max_listen_interval: max listen interval in units of beacon interval
1961 * @queues: number of available hardware transmit queues for
1962 * data packets. WMM/QoS requires at least four, these
1963 * queues need to have configurable access parameters.
1965 * @rate_control_algorithm: rate control algorithm for this hardware.
1966 * If unset (NULL), the default algorithm will be used. Must be
1967 * set before calling ieee80211_register_hw().
1969 * @vif_data_size: size (in bytes) of the drv_priv data area
1970 * within &struct ieee80211_vif.
1971 * @sta_data_size: size (in bytes) of the drv_priv data area
1972 * within &struct ieee80211_sta.
1973 * @chanctx_data_size: size (in bytes) of the drv_priv data area
1974 * within &struct ieee80211_chanctx_conf.
1975 * @txq_data_size: size (in bytes) of the drv_priv data area
1976 * within @struct ieee80211_txq.
1978 * @max_rates: maximum number of alternate rate retry stages the hw
1980 * @max_report_rates: maximum number of alternate rate retry stages
1981 * the hw can report back.
1982 * @max_rate_tries: maximum number of tries for each stage
1984 * @max_rx_aggregation_subframes: maximum buffer size (number of
1985 * sub-frames) to be used for A-MPDU block ack receiver
1987 * This is only relevant if the device has restrictions on the
1988 * number of subframes, if it relies on mac80211 to do reordering
1989 * it shouldn't be set.
1991 * @max_tx_aggregation_subframes: maximum number of subframes in an
1992 * aggregate an HT driver will transmit, used by the peer as a
1993 * hint to size its reorder buffer.
1995 * @offchannel_tx_hw_queue: HW queue ID to use for offchannel TX
1996 * (if %IEEE80211_HW_QUEUE_CONTROL is set)
1998 * @radiotap_mcs_details: lists which MCS information can the HW
1999 * reports, by default it is set to _MCS, _GI and _BW but doesn't
2000 * include _FMT. Use %IEEE80211_RADIOTAP_MCS_HAVE_* values, only
2001 * adding _BW is supported today.
2003 * @radiotap_vht_details: lists which VHT MCS information the HW reports,
2004 * the default is _GI | _BANDWIDTH.
2005 * Use the %IEEE80211_RADIOTAP_VHT_KNOWN_* values.
2007 * @netdev_features: netdev features to be set in each netdev created
2008 * from this HW. Note that not all features are usable with mac80211,
2009 * other features will be rejected during HW registration.
2011 * @uapsd_queues: This bitmap is included in (re)association frame to indicate
2012 * for each access category if it is uAPSD trigger-enabled and delivery-
2013 * enabled. Use IEEE80211_WMM_IE_STA_QOSINFO_AC_* to set this bitmap.
2014 * Each bit corresponds to different AC. Value '1' in specific bit means
2015 * that corresponding AC is both trigger- and delivery-enabled. '0' means
2018 * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may
2019 * deliver to a WMM STA during any Service Period triggered by the WMM STA.
2020 * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values.
2022 * @n_cipher_schemes: a size of an array of cipher schemes definitions.
2023 * @cipher_schemes: a pointer to an array of cipher scheme definitions
2026 * @txq_ac_max_pending: maximum number of frames per AC pending in all txq
2027 * entries for a vif.
2029 struct ieee80211_hw {
2030 struct ieee80211_conf conf;
2031 struct wiphy *wiphy;
2032 const char *rate_control_algorithm;
2035 unsigned int extra_tx_headroom;
2036 unsigned int extra_beacon_tailroom;
2039 int chanctx_data_size;
2042 u16 max_listen_interval;
2045 u8 max_report_rates;
2047 u8 max_rx_aggregation_subframes;
2048 u8 max_tx_aggregation_subframes;
2049 u8 offchannel_tx_hw_queue;
2050 u8 radiotap_mcs_details;
2051 u16 radiotap_vht_details;
2052 netdev_features_t netdev_features;
2054 u8 uapsd_max_sp_len;
2055 u8 n_cipher_schemes;
2056 const struct ieee80211_cipher_scheme *cipher_schemes;
2057 int txq_ac_max_pending;
2061 * struct ieee80211_scan_request - hw scan request
2063 * @ies: pointers different parts of IEs (in req.ie)
2064 * @req: cfg80211 request.
2066 struct ieee80211_scan_request {
2067 struct ieee80211_scan_ies ies;
2070 struct cfg80211_scan_request req;
2074 * struct ieee80211_tdls_ch_sw_params - TDLS channel switch parameters
2076 * @sta: peer this TDLS channel-switch request/response came from
2077 * @chandef: channel referenced in a TDLS channel-switch request
2078 * @action_code: see &enum ieee80211_tdls_actioncode
2079 * @status: channel-switch response status
2080 * @timestamp: time at which the frame was received
2081 * @switch_time: switch-timing parameter received in the frame
2082 * @switch_timeout: switch-timing parameter received in the frame
2083 * @tmpl_skb: TDLS switch-channel response template
2084 * @ch_sw_tm_ie: offset of the channel-switch timing IE inside @tmpl_skb
2086 struct ieee80211_tdls_ch_sw_params {
2087 struct ieee80211_sta *sta;
2088 struct cfg80211_chan_def *chandef;
2094 struct sk_buff *tmpl_skb;
2099 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
2101 * @wiphy: the &struct wiphy which we want to query
2103 * mac80211 drivers can use this to get to their respective
2104 * &struct ieee80211_hw. Drivers wishing to get to their own private
2105 * structure can then access it via hw->priv. Note that mac802111 drivers should
2106 * not use wiphy_priv() to try to get their private driver structure as this
2107 * is already used internally by mac80211.
2109 * Return: The mac80211 driver hw struct of @wiphy.
2111 struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);
2114 * SET_IEEE80211_DEV - set device for 802.11 hardware
2116 * @hw: the &struct ieee80211_hw to set the device for
2117 * @dev: the &struct device of this 802.11 device
2119 static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
2121 set_wiphy_dev(hw->wiphy, dev);
2125 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
2127 * @hw: the &struct ieee80211_hw to set the MAC address for
2128 * @addr: the address to set
2130 static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
2132 memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
2135 static inline struct ieee80211_rate *
2136 ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
2137 const struct ieee80211_tx_info *c)
2139 if (WARN_ON_ONCE(c->control.rates[0].idx < 0))
2141 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
2144 static inline struct ieee80211_rate *
2145 ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
2146 const struct ieee80211_tx_info *c)
2148 if (c->control.rts_cts_rate_idx < 0)
2150 return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
2153 static inline struct ieee80211_rate *
2154 ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
2155 const struct ieee80211_tx_info *c, int idx)
2157 if (c->control.rates[idx + 1].idx < 0)
2159 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
2163 * ieee80211_free_txskb - free TX skb
2167 * Free a transmit skb. Use this funtion when some failure
2168 * to transmit happened and thus status cannot be reported.
2170 void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb);
2173 * DOC: Hardware crypto acceleration
2175 * mac80211 is capable of taking advantage of many hardware
2176 * acceleration designs for encryption and decryption operations.
2178 * The set_key() callback in the &struct ieee80211_ops for a given
2179 * device is called to enable hardware acceleration of encryption and
2180 * decryption. The callback takes a @sta parameter that will be NULL
2181 * for default keys or keys used for transmission only, or point to
2182 * the station information for the peer for individual keys.
2183 * Multiple transmission keys with the same key index may be used when
2184 * VLANs are configured for an access point.
2186 * When transmitting, the TX control data will use the @hw_key_idx
2187 * selected by the driver by modifying the &struct ieee80211_key_conf
2188 * pointed to by the @key parameter to the set_key() function.
2190 * The set_key() call for the %SET_KEY command should return 0 if
2191 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
2192 * added; if you return 0 then hw_key_idx must be assigned to the
2193 * hardware key index, you are free to use the full u8 range.
2195 * Note that in the case that the @IEEE80211_HW_SW_CRYPTO_CONTROL flag is
2196 * set, mac80211 will not automatically fall back to software crypto if
2197 * enabling hardware crypto failed. The set_key() call may also return the
2198 * value 1 to permit this specific key/algorithm to be done in software.
2200 * When the cmd is %DISABLE_KEY then it must succeed.
2202 * Note that it is permissible to not decrypt a frame even if a key
2203 * for it has been uploaded to hardware, the stack will not make any
2204 * decision based on whether a key has been uploaded or not but rather
2205 * based on the receive flags.
2207 * The &struct ieee80211_key_conf structure pointed to by the @key
2208 * parameter is guaranteed to be valid until another call to set_key()
2209 * removes it, but it can only be used as a cookie to differentiate
2212 * In TKIP some HW need to be provided a phase 1 key, for RX decryption
2213 * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
2215 * The update_tkip_key() call updates the driver with the new phase 1 key.
2216 * This happens every time the iv16 wraps around (every 65536 packets). The
2217 * set_key() call will happen only once for each key (unless the AP did
2218 * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is
2219 * provided by update_tkip_key only. The trigger that makes mac80211 call this
2220 * handler is software decryption with wrap around of iv16.
2222 * The set_default_unicast_key() call updates the default WEP key index
2223 * configured to the hardware for WEP encryption type. This is required
2224 * for devices that support offload of data packets (e.g. ARP responses).
2228 * DOC: Powersave support
2230 * mac80211 has support for various powersave implementations.
2232 * First, it can support hardware that handles all powersaving by itself,
2233 * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware
2234 * flag. In that case, it will be told about the desired powersave mode
2235 * with the %IEEE80211_CONF_PS flag depending on the association status.
2236 * The hardware must take care of sending nullfunc frames when necessary,
2237 * i.e. when entering and leaving powersave mode. The hardware is required
2238 * to look at the AID in beacons and signal to the AP that it woke up when
2239 * it finds traffic directed to it.
2241 * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in
2242 * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
2243 * with hardware wakeup and sleep states. Driver is responsible for waking
2244 * up the hardware before issuing commands to the hardware and putting it
2245 * back to sleep at appropriate times.
2247 * When PS is enabled, hardware needs to wakeup for beacons and receive the
2248 * buffered multicast/broadcast frames after the beacon. Also it must be
2249 * possible to send frames and receive the acknowledment frame.
2251 * Other hardware designs cannot send nullfunc frames by themselves and also
2252 * need software support for parsing the TIM bitmap. This is also supported
2253 * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
2254 * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
2255 * required to pass up beacons. The hardware is still required to handle
2256 * waking up for multicast traffic; if it cannot the driver must handle that
2257 * as best as it can, mac80211 is too slow to do that.
2259 * Dynamic powersave is an extension to normal powersave in which the
2260 * hardware stays awake for a user-specified period of time after sending a
2261 * frame so that reply frames need not be buffered and therefore delayed to
2262 * the next wakeup. It's compromise of getting good enough latency when
2263 * there's data traffic and still saving significantly power in idle
2266 * Dynamic powersave is simply supported by mac80211 enabling and disabling
2267 * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS
2268 * flag and mac80211 will handle everything automatically. Additionally,
2269 * hardware having support for the dynamic PS feature may set the
2270 * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support
2271 * dynamic PS mode itself. The driver needs to look at the
2272 * @dynamic_ps_timeout hardware configuration value and use it that value
2273 * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable
2274 * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS
2275 * enabled whenever user has enabled powersave.
2277 * Driver informs U-APSD client support by enabling
2278 * %IEEE80211_VIF_SUPPORTS_UAPSD flag. The mode is configured through the
2279 * uapsd parameter in conf_tx() operation. Hardware needs to send the QoS
2280 * Nullfunc frames and stay awake until the service period has ended. To
2281 * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames
2282 * from that AC are transmitted with powersave enabled.
2284 * Note: U-APSD client mode is not yet supported with
2285 * %IEEE80211_HW_PS_NULLFUNC_STACK.
2289 * DOC: Beacon filter support
2291 * Some hardware have beacon filter support to reduce host cpu wakeups
2292 * which will reduce system power consumption. It usually works so that
2293 * the firmware creates a checksum of the beacon but omits all constantly
2294 * changing elements (TSF, TIM etc). Whenever the checksum changes the
2295 * beacon is forwarded to the host, otherwise it will be just dropped. That
2296 * way the host will only receive beacons where some relevant information
2297 * (for example ERP protection or WMM settings) have changed.
2299 * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER
2300 * interface capability. The driver needs to enable beacon filter support
2301 * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When
2302 * power save is enabled, the stack will not check for beacon loss and the
2303 * driver needs to notify about loss of beacons with ieee80211_beacon_loss().
2305 * The time (or number of beacons missed) until the firmware notifies the
2306 * driver of a beacon loss event (which in turn causes the driver to call
2307 * ieee80211_beacon_loss()) should be configurable and will be controlled
2308 * by mac80211 and the roaming algorithm in the future.
2310 * Since there may be constantly changing information elements that nothing
2311 * in the software stack cares about, we will, in the future, have mac80211
2312 * tell the driver which information elements are interesting in the sense
2313 * that we want to see changes in them. This will include
2314 * - a list of information element IDs
2315 * - a list of OUIs for the vendor information element
2317 * Ideally, the hardware would filter out any beacons without changes in the
2318 * requested elements, but if it cannot support that it may, at the expense
2319 * of some efficiency, filter out only a subset. For example, if the device
2320 * doesn't support checking for OUIs it should pass up all changes in all
2321 * vendor information elements.
2323 * Note that change, for the sake of simplification, also includes information
2324 * elements appearing or disappearing from the beacon.
2326 * Some hardware supports an "ignore list" instead, just make sure nothing
2327 * that was requested is on the ignore list, and include commonly changing
2328 * information element IDs in the ignore list, for example 11 (BSS load) and
2329 * the various vendor-assigned IEs with unknown contents (128, 129, 133-136,
2330 * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility
2331 * it could also include some currently unused IDs.
2334 * In addition to these capabilities, hardware should support notifying the
2335 * host of changes in the beacon RSSI. This is relevant to implement roaming
2336 * when no traffic is flowing (when traffic is flowing we see the RSSI of
2337 * the received data packets). This can consist in notifying the host when
2338 * the RSSI changes significantly or when it drops below or rises above
2339 * configurable thresholds. In the future these thresholds will also be
2340 * configured by mac80211 (which gets them from userspace) to implement
2341 * them as the roaming algorithm requires.
2343 * If the hardware cannot implement this, the driver should ask it to
2344 * periodically pass beacon frames to the host so that software can do the
2345 * signal strength threshold checking.
2349 * DOC: Spatial multiplexing power save
2351 * SMPS (Spatial multiplexing power save) is a mechanism to conserve
2352 * power in an 802.11n implementation. For details on the mechanism
2353 * and rationale, please refer to 802.11 (as amended by 802.11n-2009)
2354 * "11.2.3 SM power save".
2356 * The mac80211 implementation is capable of sending action frames
2357 * to update the AP about the station's SMPS mode, and will instruct
2358 * the driver to enter the specific mode. It will also announce the
2359 * requested SMPS mode during the association handshake. Hardware
2360 * support for this feature is required, and can be indicated by
2363 * The default mode will be "automatic", which nl80211/cfg80211
2364 * defines to be dynamic SMPS in (regular) powersave, and SMPS
2365 * turned off otherwise.
2367 * To support this feature, the driver must set the appropriate
2368 * hardware support flags, and handle the SMPS flag to the config()
2369 * operation. It will then with this mechanism be instructed to
2370 * enter the requested SMPS mode while associated to an HT AP.
2374 * DOC: Frame filtering
2376 * mac80211 requires to see many management frames for proper
2377 * operation, and users may want to see many more frames when
2378 * in monitor mode. However, for best CPU usage and power consumption,
2379 * having as few frames as possible percolate through the stack is
2380 * desirable. Hence, the hardware should filter as much as possible.
2382 * To achieve this, mac80211 uses filter flags (see below) to tell
2383 * the driver's configure_filter() function which frames should be
2384 * passed to mac80211 and which should be filtered out.
2386 * Before configure_filter() is invoked, the prepare_multicast()
2387 * callback is invoked with the parameters @mc_count and @mc_list
2388 * for the combined multicast address list of all virtual interfaces.
2389 * It's use is optional, and it returns a u64 that is passed to
2390 * configure_filter(). Additionally, configure_filter() has the
2391 * arguments @changed_flags telling which flags were changed and
2392 * @total_flags with the new flag states.
2394 * If your device has no multicast address filters your driver will
2395 * need to check both the %FIF_ALLMULTI flag and the @mc_count
2396 * parameter to see whether multicast frames should be accepted
2399 * All unsupported flags in @total_flags must be cleared.
2400 * Hardware does not support a flag if it is incapable of _passing_
2401 * the frame to the stack. Otherwise the driver must ignore
2402 * the flag, but not clear it.
2403 * You must _only_ clear the flag (announce no support for the
2404 * flag to mac80211) if you are not able to pass the packet type
2405 * to the stack (so the hardware always filters it).
2406 * So for example, you should clear @FIF_CONTROL, if your hardware
2407 * always filters control frames. If your hardware always passes
2408 * control frames to the kernel and is incapable of filtering them,
2409 * you do _not_ clear the @FIF_CONTROL flag.
2410 * This rule applies to all other FIF flags as well.
2414 * DOC: AP support for powersaving clients
2416 * In order to implement AP and P2P GO modes, mac80211 has support for
2417 * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD.
2418 * There currently is no support for sAPSD.
2420 * There is one assumption that mac80211 makes, namely that a client
2421 * will not poll with PS-Poll and trigger with uAPSD at the same time.
2422 * Both are supported, and both can be used by the same client, but
2423 * they can't be used concurrently by the same client. This simplifies
2426 * The first thing to keep in mind is that there is a flag for complete
2427 * driver implementation: %IEEE80211_HW_AP_LINK_PS. If this flag is set,
2428 * mac80211 expects the driver to handle most of the state machine for
2429 * powersaving clients and will ignore the PM bit in incoming frames.
2430 * Drivers then use ieee80211_sta_ps_transition() to inform mac80211 of
2431 * stations' powersave transitions. In this mode, mac80211 also doesn't
2432 * handle PS-Poll/uAPSD.
2434 * In the mode without %IEEE80211_HW_AP_LINK_PS, mac80211 will check the
2435 * PM bit in incoming frames for client powersave transitions. When a
2436 * station goes to sleep, we will stop transmitting to it. There is,
2437 * however, a race condition: a station might go to sleep while there is
2438 * data buffered on hardware queues. If the device has support for this
2439 * it will reject frames, and the driver should give the frames back to
2440 * mac80211 with the %IEEE80211_TX_STAT_TX_FILTERED flag set which will
2441 * cause mac80211 to retry the frame when the station wakes up. The
2442 * driver is also notified of powersave transitions by calling its
2443 * @sta_notify callback.
2445 * When the station is asleep, it has three choices: it can wake up,
2446 * it can PS-Poll, or it can possibly start a uAPSD service period.
2447 * Waking up is implemented by simply transmitting all buffered (and
2448 * filtered) frames to the station. This is the easiest case. When
2449 * the station sends a PS-Poll or a uAPSD trigger frame, mac80211
2450 * will inform the driver of this with the @allow_buffered_frames
2451 * callback; this callback is optional. mac80211 will then transmit
2452 * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER
2453 * on each frame. The last frame in the service period (or the only
2454 * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to
2455 * indicate that it ends the service period; as this frame must have
2456 * TX status report it also sets %IEEE80211_TX_CTL_REQ_TX_STATUS.
2457 * When TX status is reported for this frame, the service period is
2458 * marked has having ended and a new one can be started by the peer.
2460 * Additionally, non-bufferable MMPDUs can also be transmitted by
2461 * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them.
2463 * Another race condition can happen on some devices like iwlwifi
2464 * when there are frames queued for the station and it wakes up
2465 * or polls; the frames that are already queued could end up being
2466 * transmitted first instead, causing reordering and/or wrong
2467 * processing of the EOSP. The cause is that allowing frames to be
2468 * transmitted to a certain station is out-of-band communication to
2469 * the device. To allow this problem to be solved, the driver can
2470 * call ieee80211_sta_block_awake() if frames are buffered when it
2471 * is notified that the station went to sleep. When all these frames
2472 * have been filtered (see above), it must call the function again
2473 * to indicate that the station is no longer blocked.
2475 * If the driver buffers frames in the driver for aggregation in any
2476 * way, it must use the ieee80211_sta_set_buffered() call when it is
2477 * notified of the station going to sleep to inform mac80211 of any
2478 * TIDs that have frames buffered. Note that when a station wakes up
2479 * this information is reset (hence the requirement to call it when
2480 * informed of the station going to sleep). Then, when a service
2481 * period starts for any reason, @release_buffered_frames is called
2482 * with the number of frames to be released and which TIDs they are
2483 * to come from. In this case, the driver is responsible for setting
2484 * the EOSP (for uAPSD) and MORE_DATA bits in the released frames,
2485 * to help the @more_data parameter is passed to tell the driver if
2486 * there is more data on other TIDs -- the TIDs to release frames
2487 * from are ignored since mac80211 doesn't know how many frames the
2488 * buffers for those TIDs contain.
2490 * If the driver also implement GO mode, where absence periods may
2491 * shorten service periods (or abort PS-Poll responses), it must
2492 * filter those response frames except in the case of frames that
2493 * are buffered in the driver -- those must remain buffered to avoid
2494 * reordering. Because it is possible that no frames are released
2495 * in this case, the driver must call ieee80211_sta_eosp()
2496 * to indicate to mac80211 that the service period ended anyway.
2498 * Finally, if frames from multiple TIDs are released from mac80211
2499 * but the driver might reorder them, it must clear & set the flags
2500 * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP)
2501 * and also take care of the EOSP and MORE_DATA bits in the frame.
2502 * The driver may also use ieee80211_sta_eosp() in this case.
2504 * Note that if the driver ever buffers frames other than QoS-data
2505 * frames, it must take care to never send a non-QoS-data frame as
2506 * the last frame in a service period, adding a QoS-nulldata frame
2507 * after a non-QoS-data frame if needed.
2511 * DOC: HW queue control
2513 * Before HW queue control was introduced, mac80211 only had a single static
2514 * assignment of per-interface AC software queues to hardware queues. This
2515 * was problematic for a few reasons:
2516 * 1) off-channel transmissions might get stuck behind other frames
2517 * 2) multiple virtual interfaces couldn't be handled correctly
2518 * 3) after-DTIM frames could get stuck behind other frames
2520 * To solve this, hardware typically uses multiple different queues for all
2521 * the different usages, and this needs to be propagated into mac80211 so it
2522 * won't have the same problem with the software queues.
2524 * Therefore, mac80211 now offers the %IEEE80211_HW_QUEUE_CONTROL capability
2525 * flag that tells it that the driver implements its own queue control. To do
2526 * so, the driver will set up the various queues in each &struct ieee80211_vif
2527 * and the offchannel queue in &struct ieee80211_hw. In response, mac80211 will
2528 * use those queue IDs in the hw_queue field of &struct ieee80211_tx_info and
2529 * if necessary will queue the frame on the right software queue that mirrors
2530 * the hardware queue.
2531 * Additionally, the driver has to then use these HW queue IDs for the queue
2532 * management functions (ieee80211_stop_queue() et al.)
2534 * The driver is free to set up the queue mappings as needed, multiple virtual
2535 * interfaces may map to the same hardware queues if needed. The setup has to
2536 * happen during add_interface or change_interface callbacks. For example, a
2537 * driver supporting station+station and station+AP modes might decide to have
2538 * 10 hardware queues to handle different scenarios:
2540 * 4 AC HW queues for 1st vif: 0, 1, 2, 3
2541 * 4 AC HW queues for 2nd vif: 4, 5, 6, 7
2542 * after-DTIM queue for AP: 8
2543 * off-channel queue: 9
2545 * It would then set up the hardware like this:
2546 * hw.offchannel_tx_hw_queue = 9
2548 * and the first virtual interface that is added as follows:
2549 * vif.hw_queue[IEEE80211_AC_VO] = 0
2550 * vif.hw_queue[IEEE80211_AC_VI] = 1
2551 * vif.hw_queue[IEEE80211_AC_BE] = 2
2552 * vif.hw_queue[IEEE80211_AC_BK] = 3
2553 * vif.cab_queue = 8 // if AP mode, otherwise %IEEE80211_INVAL_HW_QUEUE
2554 * and the second virtual interface with 4-7.
2556 * If queue 6 gets full, for example, mac80211 would only stop the second
2557 * virtual interface's BE queue since virtual interface queues are per AC.
2559 * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE
2560 * whenever the queue is not used (i.e. the interface is not in AP mode) if the
2561 * queue could potentially be shared since mac80211 will look at cab_queue when
2562 * a queue is stopped/woken even if the interface is not in AP mode.
2566 * enum ieee80211_filter_flags - hardware filter flags
2568 * These flags determine what the filter in hardware should be
2569 * programmed to let through and what should not be passed to the
2570 * stack. It is always safe to pass more frames than requested,
2571 * but this has negative impact on power consumption.
2573 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested
2574 * by the user or if the hardware is not capable of filtering by
2575 * multicast address.
2577 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
2578 * %RX_FLAG_FAILED_FCS_CRC for them)
2580 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
2581 * the %RX_FLAG_FAILED_PLCP_CRC for them
2583 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
2584 * to the hardware that it should not filter beacons or probe responses
2585 * by BSSID. Filtering them can greatly reduce the amount of processing
2586 * mac80211 needs to do and the amount of CPU wakeups, so you should
2587 * honour this flag if possible.
2589 * @FIF_CONTROL: pass control frames (except for PS Poll) addressed to this
2592 * @FIF_OTHER_BSS: pass frames destined to other BSSes
2594 * @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only
2595 * those addressed to this station.
2597 * @FIF_PROBE_REQ: pass probe request frames
2599 enum ieee80211_filter_flags {
2600 FIF_ALLMULTI = 1<<1,
2602 FIF_PLCPFAIL = 1<<3,
2603 FIF_BCN_PRBRESP_PROMISC = 1<<4,
2605 FIF_OTHER_BSS = 1<<6,
2607 FIF_PROBE_REQ = 1<<8,
2611 * enum ieee80211_ampdu_mlme_action - A-MPDU actions
2613 * These flags are used with the ampdu_action() callback in
2614 * &struct ieee80211_ops to indicate which action is needed.
2616 * Note that drivers MUST be able to deal with a TX aggregation
2617 * session being stopped even before they OK'ed starting it by
2618 * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer
2619 * might receive the addBA frame and send a delBA right away!
2621 * @IEEE80211_AMPDU_RX_START: start RX aggregation
2622 * @IEEE80211_AMPDU_RX_STOP: stop RX aggregation
2623 * @IEEE80211_AMPDU_TX_START: start TX aggregation
2624 * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
2625 * @IEEE80211_AMPDU_TX_STOP_CONT: stop TX aggregation but continue transmitting
2626 * queued packets, now unaggregated. After all packets are transmitted the
2627 * driver has to call ieee80211_stop_tx_ba_cb_irqsafe().
2628 * @IEEE80211_AMPDU_TX_STOP_FLUSH: stop TX aggregation and flush all packets,
2629 * called when the station is removed. There's no need or reason to call
2630 * ieee80211_stop_tx_ba_cb_irqsafe() in this case as mac80211 assumes the
2631 * session is gone and removes the station.
2632 * @IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: called when TX aggregation is stopped
2633 * but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe() yet and
2634 * now the connection is dropped and the station will be removed. Drivers
2635 * should clean up and drop remaining packets when this is called.
2637 enum ieee80211_ampdu_mlme_action {
2638 IEEE80211_AMPDU_RX_START,
2639 IEEE80211_AMPDU_RX_STOP,
2640 IEEE80211_AMPDU_TX_START,
2641 IEEE80211_AMPDU_TX_STOP_CONT,
2642 IEEE80211_AMPDU_TX_STOP_FLUSH,
2643 IEEE80211_AMPDU_TX_STOP_FLUSH_CONT,
2644 IEEE80211_AMPDU_TX_OPERATIONAL,
2648 * enum ieee80211_frame_release_type - frame release reason
2649 * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll
2650 * @IEEE80211_FRAME_RELEASE_UAPSD: frame(s) released due to
2651 * frame received on trigger-enabled AC
2653 enum ieee80211_frame_release_type {
2654 IEEE80211_FRAME_RELEASE_PSPOLL,
2655 IEEE80211_FRAME_RELEASE_UAPSD,
2659 * enum ieee80211_rate_control_changed - flags to indicate what changed
2661 * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit
2662 * to this station changed. The actual bandwidth is in the station
2663 * information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40
2664 * flag changes, for HT and VHT the bandwidth field changes.
2665 * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed.
2666 * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer
2667 * changed (in IBSS mode) due to discovering more information about
2669 * @IEEE80211_RC_NSS_CHANGED: N_SS (number of spatial streams) was changed
2672 enum ieee80211_rate_control_changed {
2673 IEEE80211_RC_BW_CHANGED = BIT(0),
2674 IEEE80211_RC_SMPS_CHANGED = BIT(1),
2675 IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2),
2676 IEEE80211_RC_NSS_CHANGED = BIT(3),
2680 * enum ieee80211_roc_type - remain on channel type
2682 * With the support for multi channel contexts and multi channel operations,
2683 * remain on channel operations might be limited/deferred/aborted by other
2684 * flows/operations which have higher priority (and vise versa).
2685 * Specifying the ROC type can be used by devices to prioritize the ROC
2686 * operations compared to other operations/flows.
2688 * @IEEE80211_ROC_TYPE_NORMAL: There are no special requirements for this ROC.
2689 * @IEEE80211_ROC_TYPE_MGMT_TX: The remain on channel request is required
2690 * for sending managment frames offchannel.
2692 enum ieee80211_roc_type {
2693 IEEE80211_ROC_TYPE_NORMAL = 0,
2694 IEEE80211_ROC_TYPE_MGMT_TX,
2698 * enum ieee80211_reconfig_complete_type - reconfig type
2700 * This enum is used by the reconfig_complete() callback to indicate what
2701 * reconfiguration type was completed.
2703 * @IEEE80211_RECONFIG_TYPE_RESTART: hw restart type
2704 * (also due to resume() callback returning 1)
2705 * @IEEE80211_RECONFIG_TYPE_SUSPEND: suspend type (regardless
2706 * of wowlan configuration)
2708 enum ieee80211_reconfig_type {
2709 IEEE80211_RECONFIG_TYPE_RESTART,
2710 IEEE80211_RECONFIG_TYPE_SUSPEND,
2714 * struct ieee80211_ops - callbacks from mac80211 to the driver
2716 * This structure contains various callbacks that the driver may
2717 * handle or, in some cases, must handle, for example to configure
2718 * the hardware to a new channel or to transmit a frame.
2720 * @tx: Handler that 802.11 module calls for each transmitted frame.
2721 * skb contains the buffer starting from the IEEE 802.11 header.
2722 * The low-level driver should send the frame out based on
2723 * configuration in the TX control data. This handler should,
2724 * preferably, never fail and stop queues appropriately.
2727 * @start: Called before the first netdevice attached to the hardware
2728 * is enabled. This should turn on the hardware and must turn on
2729 * frame reception (for possibly enabled monitor interfaces.)
2730 * Returns negative error codes, these may be seen in userspace,
2732 * When the device is started it should not have a MAC address
2733 * to avoid acknowledging frames before a non-monitor device
2735 * Must be implemented and can sleep.
2737 * @stop: Called after last netdevice attached to the hardware
2738 * is disabled. This should turn off the hardware (at least
2739 * it must turn off frame reception.)
2740 * May be called right after add_interface if that rejects
2741 * an interface. If you added any work onto the mac80211 workqueue
2742 * you should ensure to cancel it on this callback.
2743 * Must be implemented and can sleep.
2745 * @suspend: Suspend the device; mac80211 itself will quiesce before and
2746 * stop transmitting and doing any other configuration, and then
2747 * ask the device to suspend. This is only invoked when WoWLAN is
2748 * configured, otherwise the device is deconfigured completely and
2749 * reconfigured at resume time.
2750 * The driver may also impose special conditions under which it
2751 * wants to use the "normal" suspend (deconfigure), say if it only
2752 * supports WoWLAN when the device is associated. In this case, it
2753 * must return 1 from this function.
2755 * @resume: If WoWLAN was configured, this indicates that mac80211 is
2756 * now resuming its operation, after this the device must be fully
2757 * functional again. If this returns an error, the only way out is
2758 * to also unregister the device. If it returns 1, then mac80211
2759 * will also go through the regular complete restart on resume.
2761 * @set_wakeup: Enable or disable wakeup when WoWLAN configuration is
2762 * modified. The reason is that device_set_wakeup_enable() is
2763 * supposed to be called when the configuration changes, not only
2766 * @add_interface: Called when a netdevice attached to the hardware is
2767 * enabled. Because it is not called for monitor mode devices, @start
2768 * and @stop must be implemented.
2769 * The driver should perform any initialization it needs before
2770 * the device can be enabled. The initial configuration for the
2771 * interface is given in the conf parameter.
2772 * The callback may refuse to add an interface by returning a
2773 * negative error code (which will be seen in userspace.)
2774 * Must be implemented and can sleep.
2776 * @change_interface: Called when a netdevice changes type. This callback
2777 * is optional, but only if it is supported can interface types be
2778 * switched while the interface is UP. The callback may sleep.
2779 * Note that while an interface is being switched, it will not be
2780 * found by the interface iteration callbacks.
2782 * @remove_interface: Notifies a driver that an interface is going down.
2783 * The @stop callback is called after this if it is the last interface
2784 * and no monitor interfaces are present.
2785 * When all interfaces are removed, the MAC address in the hardware
2786 * must be cleared so the device no longer acknowledges packets,
2787 * the mac_addr member of the conf structure is, however, set to the
2788 * MAC address of the device going away.
2789 * Hence, this callback must be implemented. It can sleep.
2791 * @config: Handler for configuration requests. IEEE 802.11 code calls this
2792 * function to change hardware configuration, e.g., channel.
2793 * This function should never fail but returns a negative error code
2794 * if it does. The callback can sleep.
2796 * @bss_info_changed: Handler for configuration requests related to BSS
2797 * parameters that may vary during BSS's lifespan, and may affect low
2798 * level driver (e.g. assoc/disassoc status, erp parameters).
2799 * This function should not be used if no BSS has been set, unless
2800 * for association indication. The @changed parameter indicates which
2801 * of the bss parameters has changed when a call is made. The callback
2804 * @prepare_multicast: Prepare for multicast filter configuration.
2805 * This callback is optional, and its return value is passed
2806 * to configure_filter(). This callback must be atomic.
2808 * @configure_filter: Configure the device's RX filter.
2809 * See the section "Frame filtering" for more information.
2810 * This callback must be implemented and can sleep.
2812 * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
2813 * must be set or cleared for a given STA. Must be atomic.
2815 * @set_key: See the section "Hardware crypto acceleration"
2816 * This callback is only called between add_interface and
2817 * remove_interface calls, i.e. while the given virtual interface
2819 * Returns a negative error code if the key can't be added.
2820 * The callback can sleep.
2822 * @update_tkip_key: See the section "Hardware crypto acceleration"
2823 * This callback will be called in the context of Rx. Called for drivers
2824 * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY.
2825 * The callback must be atomic.
2827 * @set_rekey_data: If the device supports GTK rekeying, for example while the
2828 * host is suspended, it can assign this callback to retrieve the data
2829 * necessary to do GTK rekeying, this is the KEK, KCK and replay counter.
2830 * After rekeying was done it should (for example during resume) notify
2831 * userspace of the new replay counter using ieee80211_gtk_rekey_notify().
2833 * @set_default_unicast_key: Set the default (unicast) key index, useful for
2834 * WEP when the device sends data packets autonomously, e.g. for ARP
2835 * offloading. The index can be 0-3, or -1 for unsetting it.
2837 * @hw_scan: Ask the hardware to service the scan request, no need to start
2838 * the scan state machine in stack. The scan must honour the channel
2839 * configuration done by the regulatory agent in the wiphy's
2840 * registered bands. The hardware (or the driver) needs to make sure
2841 * that power save is disabled.
2842 * The @req ie/ie_len members are rewritten by mac80211 to contain the
2843 * entire IEs after the SSID, so that drivers need not look at these
2844 * at all but just send them after the SSID -- mac80211 includes the
2845 * (extended) supported rates and HT information (where applicable).
2846 * When the scan finishes, ieee80211_scan_completed() must be called;
2847 * note that it also must be called when the scan cannot finish due to
2848 * any error unless this callback returned a negative error code.
2849 * The callback can sleep.
2851 * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan.
2852 * The driver should ask the hardware to cancel the scan (if possible),
2853 * but the scan will be completed only after the driver will call
2854 * ieee80211_scan_completed().
2855 * This callback is needed for wowlan, to prevent enqueueing a new
2856 * scan_work after the low-level driver was already suspended.
2857 * The callback can sleep.
2859 * @sched_scan_start: Ask the hardware to start scanning repeatedly at
2860 * specific intervals. The driver must call the
2861 * ieee80211_sched_scan_results() function whenever it finds results.
2862 * This process will continue until sched_scan_stop is called.
2864 * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan.
2865 * In this case, ieee80211_sched_scan_stopped() must not be called.
2867 * @sw_scan_start: Notifier function that is called just before a software scan
2868 * is started. Can be NULL, if the driver doesn't need this notification.
2869 * The mac_addr parameter allows supporting NL80211_SCAN_FLAG_RANDOM_ADDR,
2870 * the driver may set the NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR flag if it
2871 * can use this parameter. The callback can sleep.
2873 * @sw_scan_complete: Notifier function that is called just after a
2874 * software scan finished. Can be NULL, if the driver doesn't need
2875 * this notification.
2876 * The callback can sleep.
2878 * @get_stats: Return low-level statistics.
2879 * Returns zero if statistics are available.
2880 * The callback can sleep.
2882 * @get_key_seq: If your device implements encryption in hardware and does
2883 * IV/PN assignment then this callback should be provided to read the
2884 * IV/PN for the given key from hardware.
2885 * The callback must be atomic.
2887 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this
2888 * if the device does fragmentation by itself; if this callback is
2889 * implemented then the stack will not do fragmentation.
2890 * The callback can sleep.
2892 * @set_rts_threshold: Configuration of RTS threshold (if device needs it)
2893 * The callback can sleep.
2895 * @sta_add: Notifies low level driver about addition of an associated station,
2896 * AP, IBSS/WDS/mesh peer etc. This callback can sleep.
2898 * @sta_remove: Notifies low level driver about removal of an associated
2899 * station, AP, IBSS/WDS/mesh peer etc. Note that after the callback
2900 * returns it isn't safe to use the pointer, not even RCU protected;
2901 * no RCU grace period is guaranteed between returning here and freeing
2902 * the station. See @sta_pre_rcu_remove if needed.
2903 * This callback can sleep.
2905 * @sta_add_debugfs: Drivers can use this callback to add debugfs files
2906 * when a station is added to mac80211's station list. This callback
2907 * and @sta_remove_debugfs should be within a CONFIG_MAC80211_DEBUGFS
2908 * conditional. This callback can sleep.
2910 * @sta_remove_debugfs: Remove the debugfs files which were added using
2911 * @sta_add_debugfs. This callback can sleep.
2913 * @sta_notify: Notifies low level driver about power state transition of an
2914 * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating
2915 * in AP mode, this callback will not be called when the flag
2916 * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic.
2918 * @sta_state: Notifies low level driver about state transition of a
2919 * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.)
2920 * This callback is mutually exclusive with @sta_add/@sta_remove.
2921 * It must not fail for down transitions but may fail for transitions
2922 * up the list of states. Also note that after the callback returns it
2923 * isn't safe to use the pointer, not even RCU protected - no RCU grace
2924 * period is guaranteed between returning here and freeing the station.
2925 * See @sta_pre_rcu_remove if needed.
2926 * The callback can sleep.
2928 * @sta_pre_rcu_remove: Notify driver about station removal before RCU
2929 * synchronisation. This is useful if a driver needs to have station
2930 * pointers protected using RCU, it can then use this call to clear
2931 * the pointers instead of waiting for an RCU grace period to elapse
2933 * The callback can sleep.
2935 * @sta_rc_update: Notifies the driver of changes to the bitrates that can be
2936 * used to transmit to the station. The changes are advertised with bits
2937 * from &enum ieee80211_rate_control_changed and the values are reflected
2938 * in the station data. This callback should only be used when the driver
2939 * uses hardware rate control (%IEEE80211_HW_HAS_RATE_CONTROL) since
2940 * otherwise the rate control algorithm is notified directly.
2942 * @sta_rate_tbl_update: Notifies the driver that the rate table changed. This
2943 * is only used if the configured rate control algorithm actually uses
2944 * the new rate table API, and is therefore optional. Must be atomic.
2946 * @sta_statistics: Get statistics for this station. For example with beacon
2947 * filtering, the statistics kept by mac80211 might not be accurate, so
2948 * let the driver pre-fill the statistics. The driver can fill most of
2949 * the values (indicating which by setting the filled bitmap), but not
2950 * all of them make sense - see the source for which ones are possible.
2951 * Statistics that the driver doesn't fill will be filled by mac80211.
2952 * The callback can sleep.
2954 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
2955 * bursting) for a hardware TX queue.
2956 * Returns a negative error code on failure.
2957 * The callback can sleep.
2959 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
2960 * this is only used for IBSS mode BSSID merging and debugging. Is not a
2961 * required function.
2962 * The callback can sleep.
2964 * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
2965 * Currently, this is only used for IBSS mode debugging. Is not a
2966 * required function.
2967 * The callback can sleep.
2969 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
2970 * with other STAs in the IBSS. This is only used in IBSS mode. This
2971 * function is optional if the firmware/hardware takes full care of
2972 * TSF synchronization.
2973 * The callback can sleep.
2975 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
2976 * This is needed only for IBSS mode and the result of this function is
2977 * used to determine whether to reply to Probe Requests.
2978 * Returns non-zero if this device sent the last beacon.
2979 * The callback can sleep.
2981 * @ampdu_action: Perform a certain A-MPDU action
2982 * The RA/TID combination determines the destination and TID we want
2983 * the ampdu action to be performed for. The action is defined through
2984 * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
2985 * is the first frame we expect to perform the action on. Notice
2986 * that TX/RX_STOP can pass NULL for this parameter.
2987 * The @buf_size parameter is only valid when the action is set to
2988 * %IEEE80211_AMPDU_TX_OPERATIONAL and indicates the peer's reorder
2989 * buffer size (number of subframes) for this session -- the driver
2990 * may neither send aggregates containing more subframes than this
2991 * nor send aggregates in a way that lost frames would exceed the
2992 * buffer size. If just limiting the aggregate size, this would be
2993 * possible with a buf_size of 8:
2995 * - RX: 2....7 (lost frame #1)
2997 * which is invalid since #1 was now re-transmitted well past the
2998 * buffer size of 8. Correct ways to retransmit #1 would be:
2999 * - TX: 1 or 18 or 81
3000 * Even "189" would be wrong since 1 could be lost again.
3002 * Returns a negative error code on failure.
3003 * The callback can sleep.
3005 * @get_survey: Return per-channel survey information
3007 * @rfkill_poll: Poll rfkill hardware state. If you need this, you also
3008 * need to set wiphy->rfkill_poll to %true before registration,
3009 * and need to call wiphy_rfkill_set_hw_state() in the callback.
3010 * The callback can sleep.
3012 * @set_coverage_class: Set slot time for given coverage class as specified
3013 * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
3014 * accordingly; coverage class equals to -1 to enable ACK timeout
3015 * estimation algorithm (dynack). To disable dynack set valid value for
3016 * coverage class. This callback is not required and may sleep.
3018 * @testmode_cmd: Implement a cfg80211 test mode command. The passed @vif may
3019 * be %NULL. The callback can sleep.
3020 * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep.
3022 * @flush: Flush all pending frames from the hardware queue, making sure
3023 * that the hardware queues are empty. The @queues parameter is a bitmap
3024 * of queues to flush, which is useful if different virtual interfaces
3025 * use different hardware queues; it may also indicate all queues.
3026 * If the parameter @drop is set to %true, pending frames may be dropped.
3027 * Note that vif can be NULL.
3028 * The callback can sleep.
3030 * @channel_switch: Drivers that need (or want) to offload the channel
3031 * switch operation for CSAs received from the AP may implement this
3032 * callback. They must then call ieee80211_chswitch_done() to indicate
3033 * completion of the channel switch.
3035 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
3036 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
3037 * reject TX/RX mask combinations they cannot support by returning -EINVAL
3038 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
3040 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
3042 * @remain_on_channel: Starts an off-channel period on the given channel, must
3043 * call back to ieee80211_ready_on_channel() when on that channel. Note
3044 * that normal channel traffic is not stopped as this is intended for hw
3045 * offload. Frames to transmit on the off-channel channel are transmitted
3046 * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the
3047 * duration (which will always be non-zero) expires, the driver must call
3048 * ieee80211_remain_on_channel_expired().
3049 * Note that this callback may be called while the device is in IDLE and
3050 * must be accepted in this case.
3051 * This callback may sleep.
3052 * @cancel_remain_on_channel: Requests that an ongoing off-channel period is
3053 * aborted before it expires. This callback may sleep.
3055 * @set_ringparam: Set tx and rx ring sizes.
3057 * @get_ringparam: Get tx and rx ring current and maximum sizes.
3059 * @tx_frames_pending: Check if there is any pending frame in the hardware
3060 * queues before entering power save.
3062 * @set_bitrate_mask: Set a mask of rates to be used for rate control selection
3063 * when transmitting a frame. Currently only legacy rates are handled.
3064 * The callback can sleep.
3065 * @event_callback: Notify driver about any event in mac80211. See
3066 * &enum ieee80211_event_type for the different types.
3067 * The callback must be atomic.
3069 * @release_buffered_frames: Release buffered frames according to the given
3070 * parameters. In the case where the driver buffers some frames for
3071 * sleeping stations mac80211 will use this callback to tell the driver
3072 * to release some frames, either for PS-poll or uAPSD.
3073 * Note that if the @more_data parameter is %false the driver must check
3074 * if there are more frames on the given TIDs, and if there are more than
3075 * the frames being released then it must still set the more-data bit in
3076 * the frame. If the @more_data parameter is %true, then of course the
3077 * more-data bit must always be set.
3078 * The @tids parameter tells the driver which TIDs to release frames
3079 * from, for PS-poll it will always have only a single bit set.
3080 * In the case this is used for a PS-poll initiated release, the
3081 * @num_frames parameter will always be 1 so code can be shared. In
3082 * this case the driver must also set %IEEE80211_TX_STATUS_EOSP flag
3083 * on the TX status (and must report TX status) so that the PS-poll
3084 * period is properly ended. This is used to avoid sending multiple
3085 * responses for a retried PS-poll frame.
3086 * In the case this is used for uAPSD, the @num_frames parameter may be
3087 * bigger than one, but the driver may send fewer frames (it must send
3088 * at least one, however). In this case it is also responsible for
3089 * setting the EOSP flag in the QoS header of the frames. Also, when the
3090 * service period ends, the driver must set %IEEE80211_TX_STATUS_EOSP
3091 * on the last frame in the SP. Alternatively, it may call the function
3092 * ieee80211_sta_eosp() to inform mac80211 of the end of the SP.
3093 * This callback must be atomic.
3094 * @allow_buffered_frames: Prepare device to allow the given number of frames
3095 * to go out to the given station. The frames will be sent by mac80211
3096 * via the usual TX path after this call. The TX information for frames
3097 * released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set
3098 * and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case
3099 * frames from multiple TIDs are released and the driver might reorder
3100 * them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag
3101 * on the last frame and clear it on all others and also handle the EOSP
3102 * bit in the QoS header correctly. Alternatively, it can also call the
3103 * ieee80211_sta_eosp() function.
3104 * The @tids parameter is a bitmap and tells the driver which TIDs the
3105 * frames will be on; it will at most have two bits set.
3106 * This callback must be atomic.
3108 * @get_et_sset_count: Ethtool API to get string-set count.
3110 * @get_et_stats: Ethtool API to get a set of u64 stats.
3112 * @get_et_strings: Ethtool API to get a set of strings to describe stats
3113 * and perhaps other supported types of ethtool data-sets.
3115 * @mgd_prepare_tx: Prepare for transmitting a management frame for association
3116 * before associated. In multi-channel scenarios, a virtual interface is
3117 * bound to a channel before it is associated, but as it isn't associated
3118 * yet it need not necessarily be given airtime, in particular since any
3119 * transmission to a P2P GO needs to be synchronized against the GO's
3120 * powersave state. mac80211 will call this function before transmitting a
3121 * management frame prior to having successfully associated to allow the
3122 * driver to give it channel time for the transmission, to get a response
3123 * and to be able to synchronize with the GO.
3124 * The callback will be called before each transmission and upon return
3125 * mac80211 will transmit the frame right away.
3126 * The callback is optional and can (should!) sleep.
3128 * @mgd_protect_tdls_discover: Protect a TDLS discovery session. After sending
3129 * a TDLS discovery-request, we expect a reply to arrive on the AP's
3130 * channel. We must stay on the channel (no PSM, scan, etc.), since a TDLS
3131 * setup-response is a direct packet not buffered by the AP.
3132 * mac80211 will call this function just before the transmission of a TDLS
3133 * discovery-request. The recommended period of protection is at least
3134 * 2 * (DTIM period).
3135 * The callback is optional and can sleep.
3137 * @add_chanctx: Notifies device driver about new channel context creation.
3138 * @remove_chanctx: Notifies device driver about channel context destruction.
3139 * @change_chanctx: Notifies device driver about channel context changes that
3140 * may happen when combining different virtual interfaces on the same
3141 * channel context with different settings
3142 * @assign_vif_chanctx: Notifies device driver about channel context being bound
3143 * to vif. Possible use is for hw queue remapping.
3144 * @unassign_vif_chanctx: Notifies device driver about channel context being
3146 * @switch_vif_chanctx: switch a number of vifs from one chanctx to
3147 * another, as specified in the list of
3148 * @ieee80211_vif_chanctx_switch passed to the driver, according
3149 * to the mode defined in &ieee80211_chanctx_switch_mode.
3151 * @start_ap: Start operation on the AP interface, this is called after all the
3152 * information in bss_conf is set and beacon can be retrieved. A channel
3153 * context is bound before this is called. Note that if the driver uses
3154 * software scan or ROC, this (and @stop_ap) isn't called when the AP is
3155 * just "paused" for scanning/ROC, which is indicated by the beacon being
3156 * disabled/enabled via @bss_info_changed.
3157 * @stop_ap: Stop operation on the AP interface.
3159 * @reconfig_complete: Called after a call to ieee80211_restart_hw() and
3160 * during resume, when the reconfiguration has completed.
3161 * This can help the driver implement the reconfiguration step (and
3162 * indicate mac80211 is ready to receive frames).
3163 * This callback may sleep.
3165 * @ipv6_addr_change: IPv6 address assignment on the given interface changed.
3166 * Currently, this is only called for managed or P2P client interfaces.
3167 * This callback is optional; it must not sleep.
3169 * @channel_switch_beacon: Starts a channel switch to a new channel.
3170 * Beacons are modified to include CSA or ECSA IEs before calling this
3171 * function. The corresponding count fields in these IEs must be
3172 * decremented, and when they reach 1 the driver must call
3173 * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get()
3174 * get the csa counter decremented by mac80211, but must check if it is
3175 * 1 using ieee80211_csa_is_complete() after the beacon has been
3176 * transmitted and then call ieee80211_csa_finish().
3177 * If the CSA count starts as zero or 1, this function will not be called,
3178 * since there won't be any time to beacon before the switch anyway.
3179 * @pre_channel_switch: This is an optional callback that is called
3180 * before a channel switch procedure is started (ie. when a STA
3181 * gets a CSA or an userspace initiated channel-switch), allowing
3182 * the driver to prepare for the channel switch.
3183 * @post_channel_switch: This is an optional callback that is called
3184 * after a channel switch procedure is completed, allowing the
3185 * driver to go back to a normal configuration.
3187 * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all
3188 * information in bss_conf is set up and the beacon can be retrieved. A
3189 * channel context is bound before this is called.
3190 * @leave_ibss: Leave the IBSS again.
3192 * @get_expected_throughput: extract the expected throughput towards the
3193 * specified station. The returned value is expressed in Kbps. It returns 0
3194 * if the RC algorithm does not have proper data to provide.
3196 * @get_txpower: get current maximum tx power (in dBm) based on configuration
3197 * and hardware limits.
3199 * @tdls_channel_switch: Start channel-switching with a TDLS peer. The driver
3200 * is responsible for continually initiating channel-switching operations
3201 * and returning to the base channel for communication with the AP. The
3202 * driver receives a channel-switch request template and the location of
3203 * the switch-timing IE within the template as part of the invocation.
3204 * The template is valid only within the call, and the driver can
3205 * optionally copy the skb for further re-use.
3206 * @tdls_cancel_channel_switch: Stop channel-switching with a TDLS peer. Both
3207 * peers must be on the base channel when the call completes.
3208 * @tdls_recv_channel_switch: a TDLS channel-switch related frame (request or
3209 * response) has been received from a remote peer. The driver gets
3210 * parameters parsed from the incoming frame and may use them to continue
3211 * an ongoing channel-switch operation. In addition, a channel-switch
3212 * response template is provided, together with the location of the
3213 * switch-timing IE within the template. The skb can only be used within
3214 * the function call.
3216 * @wake_tx_queue: Called when new packets have been added to the queue.
3218 struct ieee80211_ops {
3219 void (*tx)(struct ieee80211_hw *hw,
3220 struct ieee80211_tx_control *control,
3221 struct sk_buff *skb);
3222 int (*start)(struct ieee80211_hw *hw);
3223 void (*stop)(struct ieee80211_hw *hw);
3225 int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan);
3226 int (*resume)(struct ieee80211_hw *hw);
3227 void (*set_wakeup)(struct ieee80211_hw *hw, bool enabled);
3229 int (*add_interface)(struct ieee80211_hw *hw,
3230 struct ieee80211_vif *vif);
3231 int (*change_interface)(struct ieee80211_hw *hw,
3232 struct ieee80211_vif *vif,
3233 enum nl80211_iftype new_type, bool p2p);
3234 void (*remove_interface)(struct ieee80211_hw *hw,
3235 struct ieee80211_vif *vif);
3236 int (*config)(struct ieee80211_hw *hw, u32 changed);
3237 void (*bss_info_changed)(struct ieee80211_hw *hw,
3238 struct ieee80211_vif *vif,
3239 struct ieee80211_bss_conf *info,
3242 int (*start_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3243 void (*stop_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3245 u64 (*prepare_multicast)(struct ieee80211_hw *hw,
3246 struct netdev_hw_addr_list *mc_list);
3247 void (*configure_filter)(struct ieee80211_hw *hw,
3248 unsigned int changed_flags,
3249 unsigned int *total_flags,
3251 int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
3253 int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
3254 struct ieee80211_vif *vif, struct ieee80211_sta *sta,
3255 struct ieee80211_key_conf *key);
3256 void (*update_tkip_key)(struct ieee80211_hw *hw,
3257 struct ieee80211_vif *vif,
3258 struct ieee80211_key_conf *conf,
3259 struct ieee80211_sta *sta,
3260 u32 iv32, u16 *phase1key);
3261 void (*set_rekey_data)(struct ieee80211_hw *hw,
3262 struct ieee80211_vif *vif,
3263 struct cfg80211_gtk_rekey_data *data);
3264 void (*set_default_unicast_key)(struct ieee80211_hw *hw,
3265 struct ieee80211_vif *vif, int idx);
3266 int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3267 struct ieee80211_scan_request *req);
3268 void (*cancel_hw_scan)(struct ieee80211_hw *hw,
3269 struct ieee80211_vif *vif);
3270 int (*sched_scan_start)(struct ieee80211_hw *hw,
3271 struct ieee80211_vif *vif,
3272 struct cfg80211_sched_scan_request *req,
3273 struct ieee80211_scan_ies *ies);
3274 int (*sched_scan_stop)(struct ieee80211_hw *hw,
3275 struct ieee80211_vif *vif);
3276 void (*sw_scan_start)(struct ieee80211_hw *hw,
3277 struct ieee80211_vif *vif,
3278 const u8 *mac_addr);
3279 void (*sw_scan_complete)(struct ieee80211_hw *hw,
3280 struct ieee80211_vif *vif);
3281 int (*get_stats)(struct ieee80211_hw *hw,
3282 struct ieee80211_low_level_stats *stats);
3283 void (*get_key_seq)(struct ieee80211_hw *hw,
3284 struct ieee80211_key_conf *key,
3285 struct ieee80211_key_seq *seq);
3286 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
3287 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
3288 int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3289 struct ieee80211_sta *sta);
3290 int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3291 struct ieee80211_sta *sta);
3292 #ifdef CONFIG_MAC80211_DEBUGFS
3293 void (*sta_add_debugfs)(struct ieee80211_hw *hw,
3294 struct ieee80211_vif *vif,
3295 struct ieee80211_sta *sta,
3296 struct dentry *dir);
3297 void (*sta_remove_debugfs)(struct ieee80211_hw *hw,
3298 struct ieee80211_vif *vif,
3299 struct ieee80211_sta *sta,
3300 struct dentry *dir);
3302 void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3303 enum sta_notify_cmd, struct ieee80211_sta *sta);
3304 int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3305 struct ieee80211_sta *sta,
3306 enum ieee80211_sta_state old_state,
3307 enum ieee80211_sta_state new_state);
3308 void (*sta_pre_rcu_remove)(struct ieee80211_hw *hw,
3309 struct ieee80211_vif *vif,
3310 struct ieee80211_sta *sta);
3311 void (*sta_rc_update)(struct ieee80211_hw *hw,
3312 struct ieee80211_vif *vif,
3313 struct ieee80211_sta *sta,
3315 void (*sta_rate_tbl_update)(struct ieee80211_hw *hw,
3316 struct ieee80211_vif *vif,
3317 struct ieee80211_sta *sta);
3318 void (*sta_statistics)(struct ieee80211_hw *hw,
3319 struct ieee80211_vif *vif,
3320 struct ieee80211_sta *sta,
3321 struct station_info *sinfo);
3322 int (*conf_tx)(struct ieee80211_hw *hw,
3323 struct ieee80211_vif *vif, u16 ac,
3324 const struct ieee80211_tx_queue_params *params);
3325 u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3326 void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3328 void (*reset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3329 int (*tx_last_beacon)(struct ieee80211_hw *hw);
3330 int (*ampdu_action)(struct ieee80211_hw *hw,
3331 struct ieee80211_vif *vif,
3332 enum ieee80211_ampdu_mlme_action action,
3333 struct ieee80211_sta *sta, u16 tid, u16 *ssn,
3335 int (*get_survey)(struct ieee80211_hw *hw, int idx,
3336 struct survey_info *survey);
3337 void (*rfkill_poll)(struct ieee80211_hw *hw);
3338 void (*set_coverage_class)(struct ieee80211_hw *hw, s16 coverage_class);
3339 #ifdef CONFIG_NL80211_TESTMODE
3340 int (*testmode_cmd)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3341 void *data, int len);
3342 int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb,
3343 struct netlink_callback *cb,
3344 void *data, int len);
3346 void (*flush)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3347 u32 queues, bool drop);
3348 void (*channel_switch)(struct ieee80211_hw *hw,
3349 struct ieee80211_vif *vif,
3350 struct ieee80211_channel_switch *ch_switch);
3351 int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant);
3352 int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant);
3354 int (*remain_on_channel)(struct ieee80211_hw *hw,
3355 struct ieee80211_vif *vif,
3356 struct ieee80211_channel *chan,
3358 enum ieee80211_roc_type type);
3359 int (*cancel_remain_on_channel)(struct ieee80211_hw *hw);
3360 int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx);
3361 void (*get_ringparam)(struct ieee80211_hw *hw,
3362 u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max);
3363 bool (*tx_frames_pending)(struct ieee80211_hw *hw);
3364 int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3365 const struct cfg80211_bitrate_mask *mask);
3366 void (*event_callback)(struct ieee80211_hw *hw,
3367 struct ieee80211_vif *vif,
3368 const struct ieee80211_event *event);
3370 void (*allow_buffered_frames)(struct ieee80211_hw *hw,
3371 struct ieee80211_sta *sta,
3372 u16 tids, int num_frames,
3373 enum ieee80211_frame_release_type reason,
3375 void (*release_buffered_frames)(struct ieee80211_hw *hw,
3376 struct ieee80211_sta *sta,
3377 u16 tids, int num_frames,
3378 enum ieee80211_frame_release_type reason,
3381 int (*get_et_sset_count)(struct ieee80211_hw *hw,
3382 struct ieee80211_vif *vif, int sset);
3383 void (*get_et_stats)(struct ieee80211_hw *hw,
3384 struct ieee80211_vif *vif,
3385 struct ethtool_stats *stats, u64 *data);
3386 void (*get_et_strings)(struct ieee80211_hw *hw,
3387 struct ieee80211_vif *vif,
3388 u32 sset, u8 *data);
3390 void (*mgd_prepare_tx)(struct ieee80211_hw *hw,
3391 struct ieee80211_vif *vif);
3393 void (*mgd_protect_tdls_discover)(struct ieee80211_hw *hw,
3394 struct ieee80211_vif *vif);
3396 int (*add_chanctx)(struct ieee80211_hw *hw,
3397 struct ieee80211_chanctx_conf *ctx);
3398 void (*remove_chanctx)(struct ieee80211_hw *hw,
3399 struct ieee80211_chanctx_conf *ctx);
3400 void (*change_chanctx)(struct ieee80211_hw *hw,
3401 struct ieee80211_chanctx_conf *ctx,
3403 int (*assign_vif_chanctx)(struct ieee80211_hw *hw,
3404 struct ieee80211_vif *vif,
3405 struct ieee80211_chanctx_conf *ctx);
3406 void (*unassign_vif_chanctx)(struct ieee80211_hw *hw,
3407 struct ieee80211_vif *vif,
3408 struct ieee80211_chanctx_conf *ctx);
3409 int (*switch_vif_chanctx)(struct ieee80211_hw *hw,
3410 struct ieee80211_vif_chanctx_switch *vifs,
3412 enum ieee80211_chanctx_switch_mode mode);
3414 void (*reconfig_complete)(struct ieee80211_hw *hw,
3415 enum ieee80211_reconfig_type reconfig_type);
3417 #if IS_ENABLED(CONFIG_IPV6)
3418 void (*ipv6_addr_change)(struct ieee80211_hw *hw,
3419 struct ieee80211_vif *vif,
3420 struct inet6_dev *idev);
3422 void (*channel_switch_beacon)(struct ieee80211_hw *hw,
3423 struct ieee80211_vif *vif,
3424 struct cfg80211_chan_def *chandef);
3425 int (*pre_channel_switch)(struct ieee80211_hw *hw,
3426 struct ieee80211_vif *vif,
3427 struct ieee80211_channel_switch *ch_switch);
3429 int (*post_channel_switch)(struct ieee80211_hw *hw,
3430 struct ieee80211_vif *vif);
3432 int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3433 void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3434 u32 (*get_expected_throughput)(struct ieee80211_sta *sta);
3435 int (*get_txpower)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3438 int (*tdls_channel_switch)(struct ieee80211_hw *hw,
3439 struct ieee80211_vif *vif,
3440 struct ieee80211_sta *sta, u8 oper_class,
3441 struct cfg80211_chan_def *chandef,
3442 struct sk_buff *tmpl_skb, u32 ch_sw_tm_ie);
3443 void (*tdls_cancel_channel_switch)(struct ieee80211_hw *hw,
3444 struct ieee80211_vif *vif,
3445 struct ieee80211_sta *sta);
3446 void (*tdls_recv_channel_switch)(struct ieee80211_hw *hw,
3447 struct ieee80211_vif *vif,
3448 struct ieee80211_tdls_ch_sw_params *params);
3450 void (*wake_tx_queue)(struct ieee80211_hw *hw,
3451 struct ieee80211_txq *txq);
3455 * ieee80211_alloc_hw_nm - Allocate a new hardware device
3457 * This must be called once for each hardware device. The returned pointer
3458 * must be used to refer to this device when calling other functions.
3459 * mac80211 allocates a private data area for the driver pointed to by
3460 * @priv in &struct ieee80211_hw, the size of this area is given as
3463 * @priv_data_len: length of private data
3464 * @ops: callbacks for this device
3465 * @requested_name: Requested name for this device.
3466 * NULL is valid value, and means use the default naming (phy%d)
3468 * Return: A pointer to the new hardware device, or %NULL on error.
3470 struct ieee80211_hw *ieee80211_alloc_hw_nm(size_t priv_data_len,
3471 const struct ieee80211_ops *ops,
3472 const char *requested_name);
3475 * ieee80211_alloc_hw - Allocate a new hardware device
3477 * This must be called once for each hardware device. The returned pointer
3478 * must be used to refer to this device when calling other functions.
3479 * mac80211 allocates a private data area for the driver pointed to by
3480 * @priv in &struct ieee80211_hw, the size of this area is given as
3483 * @priv_data_len: length of private data
3484 * @ops: callbacks for this device
3486 * Return: A pointer to the new hardware device, or %NULL on error.
3489 struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
3490 const struct ieee80211_ops *ops)
3492 return ieee80211_alloc_hw_nm(priv_data_len, ops, NULL);
3496 * ieee80211_register_hw - Register hardware device
3498 * You must call this function before any other functions in
3499 * mac80211. Note that before a hardware can be registered, you
3500 * need to fill the contained wiphy's information.
3502 * @hw: the device to register as returned by ieee80211_alloc_hw()
3504 * Return: 0 on success. An error code otherwise.
3506 int ieee80211_register_hw(struct ieee80211_hw *hw);
3509 * struct ieee80211_tpt_blink - throughput blink description
3510 * @throughput: throughput in Kbit/sec
3511 * @blink_time: blink time in milliseconds
3512 * (full cycle, ie. one off + one on period)
3514 struct ieee80211_tpt_blink {
3520 * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags
3521 * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio
3522 * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working
3523 * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one
3524 * interface is connected in some way, including being an AP
3526 enum ieee80211_tpt_led_trigger_flags {
3527 IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0),
3528 IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1),
3529 IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2),
3532 #ifdef CONFIG_MAC80211_LEDS
3533 const char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
3534 const char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
3535 const char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
3536 const char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
3538 __ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw,
3540 const struct ieee80211_tpt_blink *blink_table,
3541 unsigned int blink_table_len);
3544 * ieee80211_get_tx_led_name - get name of TX LED
3546 * mac80211 creates a transmit LED trigger for each wireless hardware
3547 * that can be used to drive LEDs if your driver registers a LED device.
3548 * This function returns the name (or %NULL if not configured for LEDs)
3549 * of the trigger so you can automatically link the LED device.
3551 * @hw: the hardware to get the LED trigger name for
3553 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
3555 static inline const char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
3557 #ifdef CONFIG_MAC80211_LEDS
3558 return __ieee80211_get_tx_led_name(hw);
3565 * ieee80211_get_rx_led_name - get name of RX LED
3567 * mac80211 creates a receive LED trigger for each wireless hardware
3568 * that can be used to drive LEDs if your driver registers a LED device.
3569 * This function returns the name (or %NULL if not configured for LEDs)
3570 * of the trigger so you can automatically link the LED device.
3572 * @hw: the hardware to get the LED trigger name for
3574 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
3576 static inline const char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
3578 #ifdef CONFIG_MAC80211_LEDS
3579 return __ieee80211_get_rx_led_name(hw);
3586 * ieee80211_get_assoc_led_name - get name of association LED
3588 * mac80211 creates a association LED trigger for each wireless hardware
3589 * that can be used to drive LEDs if your driver registers a LED device.
3590 * This function returns the name (or %NULL if not configured for LEDs)
3591 * of the trigger so you can automatically link the LED device.
3593 * @hw: the hardware to get the LED trigger name for
3595 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
3597 static inline const char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
3599 #ifdef CONFIG_MAC80211_LEDS
3600 return __ieee80211_get_assoc_led_name(hw);
3607 * ieee80211_get_radio_led_name - get name of radio LED
3609 * mac80211 creates a radio change LED trigger for each wireless hardware
3610 * that can be used to drive LEDs if your driver registers a LED device.
3611 * This function returns the name (or %NULL if not configured for LEDs)
3612 * of the trigger so you can automatically link the LED device.
3614 * @hw: the hardware to get the LED trigger name for
3616 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
3618 static inline const char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
3620 #ifdef CONFIG_MAC80211_LEDS
3621 return __ieee80211_get_radio_led_name(hw);
3628 * ieee80211_create_tpt_led_trigger - create throughput LED trigger
3629 * @hw: the hardware to create the trigger for
3630 * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags
3631 * @blink_table: the blink table -- needs to be ordered by throughput
3632 * @blink_table_len: size of the blink table
3634 * Return: %NULL (in case of error, or if no LED triggers are
3635 * configured) or the name of the new trigger.
3637 * Note: This function must be called before ieee80211_register_hw().
3639 static inline const char *
3640 ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags,
3641 const struct ieee80211_tpt_blink *blink_table,
3642 unsigned int blink_table_len)
3644 #ifdef CONFIG_MAC80211_LEDS
3645 return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table,
3653 * ieee80211_unregister_hw - Unregister a hardware device
3655 * This function instructs mac80211 to free allocated resources
3656 * and unregister netdevices from the networking subsystem.
3658 * @hw: the hardware to unregister
3660 void ieee80211_unregister_hw(struct ieee80211_hw *hw);
3663 * ieee80211_free_hw - free hardware descriptor
3665 * This function frees everything that was allocated, including the
3666 * private data for the driver. You must call ieee80211_unregister_hw()
3667 * before calling this function.
3669 * @hw: the hardware to free
3671 void ieee80211_free_hw(struct ieee80211_hw *hw);
3674 * ieee80211_restart_hw - restart hardware completely
3676 * Call this function when the hardware was restarted for some reason
3677 * (hardware error, ...) and the driver is unable to restore its state
3678 * by itself. mac80211 assumes that at this point the driver/hardware
3679 * is completely uninitialised and stopped, it starts the process by
3680 * calling the ->start() operation. The driver will need to reset all
3681 * internal state that it has prior to calling this function.
3683 * @hw: the hardware to restart
3685 void ieee80211_restart_hw(struct ieee80211_hw *hw);
3688 * ieee80211_napi_add - initialize mac80211 NAPI context
3689 * @hw: the hardware to initialize the NAPI context on
3690 * @napi: the NAPI context to initialize
3691 * @napi_dev: dummy NAPI netdevice, here to not waste the space if the
3692 * driver doesn't use NAPI
3693 * @poll: poll function
3694 * @weight: default weight
3696 * See also netif_napi_add().
3698 void ieee80211_napi_add(struct ieee80211_hw *hw, struct napi_struct *napi,
3699 struct net_device *napi_dev,
3700 int (*poll)(struct napi_struct *, int),
3704 * ieee80211_rx - receive frame
3706 * Use this function to hand received frames to mac80211. The receive
3707 * buffer in @skb must start with an IEEE 802.11 header. In case of a
3708 * paged @skb is used, the driver is recommended to put the ieee80211
3709 * header of the frame on the linear part of the @skb to avoid memory
3710 * allocation and/or memcpy by the stack.
3712 * This function may not be called in IRQ context. Calls to this function
3713 * for a single hardware must be synchronized against each other. Calls to
3714 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
3715 * mixed for a single hardware. Must not run concurrently with
3716 * ieee80211_tx_status() or ieee80211_tx_status_ni().
3718 * In process context use instead ieee80211_rx_ni().
3720 * @hw: the hardware this frame came in on
3721 * @skb: the buffer to receive, owned by mac80211 after this call
3723 void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb);
3726 * ieee80211_rx_irqsafe - receive frame
3728 * Like ieee80211_rx() but can be called in IRQ context
3729 * (internally defers to a tasklet.)
3731 * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
3732 * be mixed for a single hardware.Must not run concurrently with
3733 * ieee80211_tx_status() or ieee80211_tx_status_ni().
3735 * @hw: the hardware this frame came in on
3736 * @skb: the buffer to receive, owned by mac80211 after this call
3738 void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb);
3741 * ieee80211_rx_ni - receive frame (in process context)
3743 * Like ieee80211_rx() but can be called in process context
3744 * (internally disables bottom halves).
3746 * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
3747 * not be mixed for a single hardware. Must not run concurrently with
3748 * ieee80211_tx_status() or ieee80211_tx_status_ni().
3750 * @hw: the hardware this frame came in on
3751 * @skb: the buffer to receive, owned by mac80211 after this call
3753 static inline void ieee80211_rx_ni(struct ieee80211_hw *hw,
3754 struct sk_buff *skb)
3757 ieee80211_rx(hw, skb);
3762 * ieee80211_sta_ps_transition - PS transition for connected sta
3764 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS
3765 * flag set, use this function to inform mac80211 about a connected station
3766 * entering/leaving PS mode.
3768 * This function may not be called in IRQ context or with softirqs enabled.
3770 * Calls to this function for a single hardware must be synchronized against
3773 * @sta: currently connected sta
3774 * @start: start or stop PS
3776 * Return: 0 on success. -EINVAL when the requested PS mode is already set.
3778 int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start);
3781 * ieee80211_sta_ps_transition_ni - PS transition for connected sta
3782 * (in process context)
3784 * Like ieee80211_sta_ps_transition() but can be called in process context
3785 * (internally disables bottom halves). Concurrent call restriction still
3788 * @sta: currently connected sta
3789 * @start: start or stop PS
3791 * Return: Like ieee80211_sta_ps_transition().
3793 static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta,
3799 ret = ieee80211_sta_ps_transition(sta, start);
3806 * The TX headroom reserved by mac80211 for its own tx_status functions.
3807 * This is enough for the radiotap header.
3809 #define IEEE80211_TX_STATUS_HEADROOM 14
3812 * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames
3813 * @sta: &struct ieee80211_sta pointer for the sleeping station
3814 * @tid: the TID that has buffered frames
3815 * @buffered: indicates whether or not frames are buffered for this TID
3817 * If a driver buffers frames for a powersave station instead of passing
3818 * them back to mac80211 for retransmission, the station may still need
3819 * to be told that there are buffered frames via the TIM bit.
3821 * This function informs mac80211 whether or not there are frames that are
3822 * buffered in the driver for a given TID; mac80211 can then use this data
3823 * to set the TIM bit (NOTE: This may call back into the driver's set_tim
3824 * call! Beware of the locking!)
3826 * If all frames are released to the station (due to PS-poll or uAPSD)
3827 * then the driver needs to inform mac80211 that there no longer are
3828 * frames buffered. However, when the station wakes up mac80211 assumes
3829 * that all buffered frames will be transmitted and clears this data,
3830 * drivers need to make sure they inform mac80211 about all buffered
3831 * frames on the sleep transition (sta_notify() with %STA_NOTIFY_SLEEP).
3833 * Note that technically mac80211 only needs to know this per AC, not per
3834 * TID, but since driver buffering will inevitably happen per TID (since
3835 * it is related to aggregation) it is easier to make mac80211 map the
3836 * TID to the AC as required instead of keeping track in all drivers that
3839 void ieee80211_sta_set_buffered(struct ieee80211_sta *sta,
3840 u8 tid, bool buffered);
3843 * ieee80211_get_tx_rates - get the selected transmit rates for a packet
3845 * Call this function in a driver with per-packet rate selection support
3846 * to combine the rate info in the packet tx info with the most recent
3847 * rate selection table for the station entry.
3849 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3850 * @sta: the receiver station to which this packet is sent.
3851 * @skb: the frame to be transmitted.
3852 * @dest: buffer for extracted rate/retry information
3853 * @max_rates: maximum number of rates to fetch
3855 void ieee80211_get_tx_rates(struct ieee80211_vif *vif,
3856 struct ieee80211_sta *sta,
3857 struct sk_buff *skb,
3858 struct ieee80211_tx_rate *dest,
3862 * ieee80211_tx_status - transmit status callback
3864 * Call this function for all transmitted frames after they have been
3865 * transmitted. It is permissible to not call this function for
3866 * multicast frames but this can affect statistics.
3868 * This function may not be called in IRQ context. Calls to this function
3869 * for a single hardware must be synchronized against each other. Calls
3870 * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe()
3871 * may not be mixed for a single hardware. Must not run concurrently with
3872 * ieee80211_rx() or ieee80211_rx_ni().
3874 * @hw: the hardware the frame was transmitted by
3875 * @skb: the frame that was transmitted, owned by mac80211 after this call
3877 void ieee80211_tx_status(struct ieee80211_hw *hw,
3878 struct sk_buff *skb);
3881 * ieee80211_tx_status_noskb - transmit status callback without skb
3883 * This function can be used as a replacement for ieee80211_tx_status
3884 * in drivers that cannot reliably map tx status information back to
3887 * Calls to this function for a single hardware must be synchronized
3888 * against each other. Calls to this function, ieee80211_tx_status_ni()
3889 * and ieee80211_tx_status_irqsafe() may not be mixed for a single hardware.
3891 * @hw: the hardware the frame was transmitted by
3892 * @sta: the receiver station to which this packet is sent
3893 * (NULL for multicast packets)
3894 * @info: tx status information
3896 void ieee80211_tx_status_noskb(struct ieee80211_hw *hw,
3897 struct ieee80211_sta *sta,
3898 struct ieee80211_tx_info *info);
3901 * ieee80211_tx_status_ni - transmit status callback (in process context)
3903 * Like ieee80211_tx_status() but can be called in process context.
3905 * Calls to this function, ieee80211_tx_status() and
3906 * ieee80211_tx_status_irqsafe() may not be mixed
3907 * for a single hardware.
3909 * @hw: the hardware the frame was transmitted by
3910 * @skb: the frame that was transmitted, owned by mac80211 after this call
3912 static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw,
3913 struct sk_buff *skb)
3916 ieee80211_tx_status(hw, skb);
3921 * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
3923 * Like ieee80211_tx_status() but can be called in IRQ context
3924 * (internally defers to a tasklet.)
3926 * Calls to this function, ieee80211_tx_status() and
3927 * ieee80211_tx_status_ni() may not be mixed for a single hardware.
3929 * @hw: the hardware the frame was transmitted by
3930 * @skb: the frame that was transmitted, owned by mac80211 after this call
3932 void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
3933 struct sk_buff *skb);
3936 * ieee80211_report_low_ack - report non-responding station
3938 * When operating in AP-mode, call this function to report a non-responding
3941 * @sta: the non-responding connected sta
3942 * @num_packets: number of packets sent to @sta without a response
3944 void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets);
3946 #define IEEE80211_MAX_CSA_COUNTERS_NUM 2
3949 * struct ieee80211_mutable_offsets - mutable beacon offsets
3950 * @tim_offset: position of TIM element
3951 * @tim_length: size of TIM element
3952 * @csa_counter_offs: array of IEEE80211_MAX_CSA_COUNTERS_NUM offsets
3953 * to CSA counters. This array can contain zero values which
3954 * should be ignored.
3956 struct ieee80211_mutable_offsets {
3960 u16 csa_counter_offs[IEEE80211_MAX_CSA_COUNTERS_NUM];
3964 * ieee80211_beacon_get_template - beacon template generation function
3965 * @hw: pointer obtained from ieee80211_alloc_hw().
3966 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3967 * @offs: &struct ieee80211_mutable_offsets pointer to struct that will
3968 * receive the offsets that may be updated by the driver.
3970 * If the driver implements beaconing modes, it must use this function to
3971 * obtain the beacon template.
3973 * This function should be used if the beacon frames are generated by the
3974 * device, and then the driver must use the returned beacon as the template
3975 * The driver or the device are responsible to update the DTIM and, when
3976 * applicable, the CSA count.
3978 * The driver is responsible for freeing the returned skb.
3980 * Return: The beacon template. %NULL on error.
3983 ieee80211_beacon_get_template(struct ieee80211_hw *hw,
3984 struct ieee80211_vif *vif,
3985 struct ieee80211_mutable_offsets *offs);
3988 * ieee80211_beacon_get_tim - beacon generation function
3989 * @hw: pointer obtained from ieee80211_alloc_hw().
3990 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3991 * @tim_offset: pointer to variable that will receive the TIM IE offset.
3992 * Set to 0 if invalid (in non-AP modes).
3993 * @tim_length: pointer to variable that will receive the TIM IE length,
3994 * (including the ID and length bytes!).
3995 * Set to 0 if invalid (in non-AP modes).
3997 * If the driver implements beaconing modes, it must use this function to
3998 * obtain the beacon frame.
4000 * If the beacon frames are generated by the host system (i.e., not in
4001 * hardware/firmware), the driver uses this function to get each beacon
4002 * frame from mac80211 -- it is responsible for calling this function exactly
4003 * once before the beacon is needed (e.g. based on hardware interrupt).
4005 * The driver is responsible for freeing the returned skb.
4007 * Return: The beacon template. %NULL on error.
4009 struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw,
4010 struct ieee80211_vif *vif,
4011 u16 *tim_offset, u16 *tim_length);
4014 * ieee80211_beacon_get - beacon generation function
4015 * @hw: pointer obtained from ieee80211_alloc_hw().
4016 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4018 * See ieee80211_beacon_get_tim().
4020 * Return: See ieee80211_beacon_get_tim().
4022 static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
4023 struct ieee80211_vif *vif)
4025 return ieee80211_beacon_get_tim(hw, vif, NULL, NULL);
4029 * ieee80211_csa_update_counter - request mac80211 to decrement the csa counter
4030 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4032 * The csa counter should be updated after each beacon transmission.
4033 * This function is called implicitly when
4034 * ieee80211_beacon_get/ieee80211_beacon_get_tim are called, however if the
4035 * beacon frames are generated by the device, the driver should call this
4036 * function after each beacon transmission to sync mac80211's csa counters.
4038 * Return: new csa counter value
4040 u8 ieee80211_csa_update_counter(struct ieee80211_vif *vif);
4043 * ieee80211_csa_finish - notify mac80211 about channel switch
4044 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4046 * After a channel switch announcement was scheduled and the counter in this
4047 * announcement hits 1, this function must be called by the driver to
4048 * notify mac80211 that the channel can be changed.
4050 void ieee80211_csa_finish(struct ieee80211_vif *vif);
4053 * ieee80211_csa_is_complete - find out if counters reached 1
4054 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4056 * This function returns whether the channel switch counters reached zero.
4058 bool ieee80211_csa_is_complete(struct ieee80211_vif *vif);
4062 * ieee80211_proberesp_get - retrieve a Probe Response template
4063 * @hw: pointer obtained from ieee80211_alloc_hw().
4064 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4066 * Creates a Probe Response template which can, for example, be uploaded to
4067 * hardware. The destination address should be set by the caller.
4069 * Can only be called in AP mode.
4071 * Return: The Probe Response template. %NULL on error.
4073 struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw,
4074 struct ieee80211_vif *vif);
4077 * ieee80211_pspoll_get - retrieve a PS Poll template
4078 * @hw: pointer obtained from ieee80211_alloc_hw().
4079 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4081 * Creates a PS Poll a template which can, for example, uploaded to
4082 * hardware. The template must be updated after association so that correct
4083 * AID, BSSID and MAC address is used.
4085 * Note: Caller (or hardware) is responsible for setting the
4086 * &IEEE80211_FCTL_PM bit.
4088 * Return: The PS Poll template. %NULL on error.
4090 struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw,
4091 struct ieee80211_vif *vif);
4094 * ieee80211_nullfunc_get - retrieve a nullfunc template
4095 * @hw: pointer obtained from ieee80211_alloc_hw().
4096 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4098 * Creates a Nullfunc template which can, for example, uploaded to
4099 * hardware. The template must be updated after association so that correct
4100 * BSSID and address is used.
4102 * Note: Caller (or hardware) is responsible for setting the
4103 * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields.
4105 * Return: The nullfunc template. %NULL on error.
4107 struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw,
4108 struct ieee80211_vif *vif);
4111 * ieee80211_probereq_get - retrieve a Probe Request template
4112 * @hw: pointer obtained from ieee80211_alloc_hw().
4113 * @src_addr: source MAC address
4114 * @ssid: SSID buffer
4115 * @ssid_len: length of SSID
4116 * @tailroom: tailroom to reserve at end of SKB for IEs
4118 * Creates a Probe Request template which can, for example, be uploaded to
4121 * Return: The Probe Request template. %NULL on error.
4123 struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw,
4125 const u8 *ssid, size_t ssid_len,
4129 * ieee80211_rts_get - RTS frame generation function
4130 * @hw: pointer obtained from ieee80211_alloc_hw().
4131 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4132 * @frame: pointer to the frame that is going to be protected by the RTS.
4133 * @frame_len: the frame length (in octets).
4134 * @frame_txctl: &struct ieee80211_tx_info of the frame.
4135 * @rts: The buffer where to store the RTS frame.
4137 * If the RTS frames are generated by the host system (i.e., not in
4138 * hardware/firmware), the low-level driver uses this function to receive
4139 * the next RTS frame from the 802.11 code. The low-level is responsible
4140 * for calling this function before and RTS frame is needed.
4142 void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4143 const void *frame, size_t frame_len,
4144 const struct ieee80211_tx_info *frame_txctl,
4145 struct ieee80211_rts *rts);
4148 * ieee80211_rts_duration - Get the duration field for an RTS frame
4149 * @hw: pointer obtained from ieee80211_alloc_hw().
4150 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4151 * @frame_len: the length of the frame that is going to be protected by the RTS.
4152 * @frame_txctl: &struct ieee80211_tx_info of the frame.
4154 * If the RTS is generated in firmware, but the host system must provide
4155 * the duration field, the low-level driver uses this function to receive
4156 * the duration field value in little-endian byteorder.
4158 * Return: The duration.
4160 __le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
4161 struct ieee80211_vif *vif, size_t frame_len,
4162 const struct ieee80211_tx_info *frame_txctl);
4165 * ieee80211_ctstoself_get - CTS-to-self frame generation function
4166 * @hw: pointer obtained from ieee80211_alloc_hw().
4167 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4168 * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
4169 * @frame_len: the frame length (in octets).
4170 * @frame_txctl: &struct ieee80211_tx_info of the frame.
4171 * @cts: The buffer where to store the CTS-to-self frame.
4173 * If the CTS-to-self frames are generated by the host system (i.e., not in
4174 * hardware/firmware), the low-level driver uses this function to receive
4175 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
4176 * for calling this function before and CTS-to-self frame is needed.
4178 void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
4179 struct ieee80211_vif *vif,
4180 const void *frame, size_t frame_len,
4181 const struct ieee80211_tx_info *frame_txctl,
4182 struct ieee80211_cts *cts);
4185 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
4186 * @hw: pointer obtained from ieee80211_alloc_hw().
4187 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4188 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
4189 * @frame_txctl: &struct ieee80211_tx_info of the frame.
4191 * If the CTS-to-self is generated in firmware, but the host system must provide
4192 * the duration field, the low-level driver uses this function to receive
4193 * the duration field value in little-endian byteorder.
4195 * Return: The duration.
4197 __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
4198 struct ieee80211_vif *vif,
4200 const struct ieee80211_tx_info *frame_txctl);
4203 * ieee80211_generic_frame_duration - Calculate the duration field for a frame
4204 * @hw: pointer obtained from ieee80211_alloc_hw().
4205 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4206 * @band: the band to calculate the frame duration on
4207 * @frame_len: the length of the frame.
4208 * @rate: the rate at which the frame is going to be transmitted.
4210 * Calculate the duration field of some generic frame, given its
4211 * length and transmission rate (in 100kbps).
4213 * Return: The duration.
4215 __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
4216 struct ieee80211_vif *vif,
4217 enum ieee80211_band band,
4219 struct ieee80211_rate *rate);
4222 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
4223 * @hw: pointer as obtained from ieee80211_alloc_hw().
4224 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4226 * Function for accessing buffered broadcast and multicast frames. If
4227 * hardware/firmware does not implement buffering of broadcast/multicast
4228 * frames when power saving is used, 802.11 code buffers them in the host
4229 * memory. The low-level driver uses this function to fetch next buffered
4230 * frame. In most cases, this is used when generating beacon frame.
4232 * Return: A pointer to the next buffered skb or NULL if no more buffered
4233 * frames are available.
4235 * Note: buffered frames are returned only after DTIM beacon frame was
4236 * generated with ieee80211_beacon_get() and the low-level driver must thus
4237 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
4238 * NULL if the previous generated beacon was not DTIM, so the low-level driver
4239 * does not need to check for DTIM beacons separately and should be able to
4240 * use common code for all beacons.
4243 ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4246 * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32
4248 * This function returns the TKIP phase 1 key for the given IV32.
4250 * @keyconf: the parameter passed with the set key
4251 * @iv32: IV32 to get the P1K for
4252 * @p1k: a buffer to which the key will be written, as 5 u16 values
4254 void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf,
4255 u32 iv32, u16 *p1k);
4258 * ieee80211_get_tkip_p1k - get a TKIP phase 1 key
4260 * This function returns the TKIP phase 1 key for the IV32 taken
4261 * from the given packet.
4263 * @keyconf: the parameter passed with the set key
4264 * @skb: the packet to take the IV32 value from that will be encrypted
4266 * @p1k: a buffer to which the key will be written, as 5 u16 values
4268 static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf,
4269 struct sk_buff *skb, u16 *p1k)
4271 struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
4272 const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control);
4273 u32 iv32 = get_unaligned_le32(&data[4]);
4275 ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k);
4279 * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX
4281 * This function returns the TKIP phase 1 key for the given IV32
4282 * and transmitter address.
4284 * @keyconf: the parameter passed with the set key
4285 * @ta: TA that will be used with the key
4286 * @iv32: IV32 to get the P1K for
4287 * @p1k: a buffer to which the key will be written, as 5 u16 values
4289 void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf,
4290 const u8 *ta, u32 iv32, u16 *p1k);
4293 * ieee80211_get_tkip_p2k - get a TKIP phase 2 key
4295 * This function computes the TKIP RC4 key for the IV values
4298 * @keyconf: the parameter passed with the set key
4299 * @skb: the packet to take the IV32/IV16 values from that will be
4300 * encrypted with this key
4301 * @p2k: a buffer to which the key will be written, 16 bytes
4303 void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf,
4304 struct sk_buff *skb, u8 *p2k);
4307 * ieee80211_aes_cmac_calculate_k1_k2 - calculate the AES-CMAC sub keys
4309 * This function computes the two AES-CMAC sub-keys, based on the
4310 * previously installed master key.
4312 * @keyconf: the parameter passed with the set key
4313 * @k1: a buffer to be filled with the 1st sub-key
4314 * @k2: a buffer to be filled with the 2nd sub-key
4316 void ieee80211_aes_cmac_calculate_k1_k2(struct ieee80211_key_conf *keyconf,
4320 * ieee80211_get_key_tx_seq - get key TX sequence counter
4322 * @keyconf: the parameter passed with the set key
4323 * @seq: buffer to receive the sequence data
4325 * This function allows a driver to retrieve the current TX IV/PN
4326 * for the given key. It must not be called if IV generation is
4327 * offloaded to the device.
4329 * Note that this function may only be called when no TX processing
4330 * can be done concurrently, for example when queues are stopped
4331 * and the stop has been synchronized.
4333 void ieee80211_get_key_tx_seq(struct ieee80211_key_conf *keyconf,
4334 struct ieee80211_key_seq *seq);
4337 * ieee80211_get_key_rx_seq - get key RX sequence counter
4339 * @keyconf: the parameter passed with the set key
4340 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
4341 * the value on TID 0 is also used for non-QoS frames. For
4342 * CMAC, only TID 0 is valid.
4343 * @seq: buffer to receive the sequence data
4345 * This function allows a driver to retrieve the current RX IV/PNs
4346 * for the given key. It must not be called if IV checking is done
4347 * by the device and not by mac80211.
4349 * Note that this function may only be called when no RX processing
4350 * can be done concurrently.
4352 void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf,
4353 int tid, struct ieee80211_key_seq *seq);
4356 * ieee80211_set_key_tx_seq - set key TX sequence counter
4358 * @keyconf: the parameter passed with the set key
4359 * @seq: new sequence data
4361 * This function allows a driver to set the current TX IV/PNs for the
4362 * given key. This is useful when resuming from WoWLAN sleep and the
4363 * device may have transmitted frames using the PTK, e.g. replies to
4366 * Note that this function may only be called when no TX processing
4367 * can be done concurrently.
4369 void ieee80211_set_key_tx_seq(struct ieee80211_key_conf *keyconf,
4370 struct ieee80211_key_seq *seq);
4373 * ieee80211_set_key_rx_seq - set key RX sequence counter
4375 * @keyconf: the parameter passed with the set key
4376 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
4377 * the value on TID 0 is also used for non-QoS frames. For
4378 * CMAC, only TID 0 is valid.
4379 * @seq: new sequence data
4381 * This function allows a driver to set the current RX IV/PNs for the
4382 * given key. This is useful when resuming from WoWLAN sleep and GTK
4383 * rekey may have been done while suspended. It should not be called
4384 * if IV checking is done by the device and not by mac80211.
4386 * Note that this function may only be called when no RX processing
4387 * can be done concurrently.
4389 void ieee80211_set_key_rx_seq(struct ieee80211_key_conf *keyconf,
4390 int tid, struct ieee80211_key_seq *seq);
4393 * ieee80211_remove_key - remove the given key
4394 * @keyconf: the parameter passed with the set key
4396 * Remove the given key. If the key was uploaded to the hardware at the
4397 * time this function is called, it is not deleted in the hardware but
4398 * instead assumed to have been removed already.
4400 * Note that due to locking considerations this function can (currently)
4401 * only be called during key iteration (ieee80211_iter_keys().)
4403 void ieee80211_remove_key(struct ieee80211_key_conf *keyconf);
4406 * ieee80211_gtk_rekey_add - add a GTK key from rekeying during WoWLAN
4407 * @vif: the virtual interface to add the key on
4408 * @keyconf: new key data
4410 * When GTK rekeying was done while the system was suspended, (a) new
4411 * key(s) will be available. These will be needed by mac80211 for proper
4412 * RX processing, so this function allows setting them.
4414 * The function returns the newly allocated key structure, which will
4415 * have similar contents to the passed key configuration but point to
4416 * mac80211-owned memory. In case of errors, the function returns an
4417 * ERR_PTR(), use IS_ERR() etc.
4419 * Note that this function assumes the key isn't added to hardware
4420 * acceleration, so no TX will be done with the key. Since it's a GTK
4421 * on managed (station) networks, this is true anyway. If the driver
4422 * calls this function from the resume callback and subsequently uses
4423 * the return code 1 to reconfigure the device, this key will be part
4424 * of the reconfiguration.
4426 * Note that the driver should also call ieee80211_set_key_rx_seq()
4427 * for the new key for each TID to set up sequence counters properly.
4429 * IMPORTANT: If this replaces a key that is present in the hardware,
4430 * then it will attempt to remove it during this call. In many cases
4431 * this isn't what you want, so call ieee80211_remove_key() first for
4432 * the key that's being replaced.
4434 struct ieee80211_key_conf *
4435 ieee80211_gtk_rekey_add(struct ieee80211_vif *vif,
4436 struct ieee80211_key_conf *keyconf);
4439 * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying
4440 * @vif: virtual interface the rekeying was done on
4441 * @bssid: The BSSID of the AP, for checking association
4442 * @replay_ctr: the new replay counter after GTK rekeying
4443 * @gfp: allocation flags
4445 void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid,
4446 const u8 *replay_ctr, gfp_t gfp);
4449 * ieee80211_wake_queue - wake specific queue
4450 * @hw: pointer as obtained from ieee80211_alloc_hw().
4451 * @queue: queue number (counted from zero).
4453 * Drivers should use this function instead of netif_wake_queue.
4455 void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);
4458 * ieee80211_stop_queue - stop specific queue
4459 * @hw: pointer as obtained from ieee80211_alloc_hw().
4460 * @queue: queue number (counted from zero).
4462 * Drivers should use this function instead of netif_stop_queue.
4464 void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
4467 * ieee80211_queue_stopped - test status of the queue
4468 * @hw: pointer as obtained from ieee80211_alloc_hw().
4469 * @queue: queue number (counted from zero).
4471 * Drivers should use this function instead of netif_stop_queue.
4473 * Return: %true if the queue is stopped. %false otherwise.
4476 int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue);
4479 * ieee80211_stop_queues - stop all queues
4480 * @hw: pointer as obtained from ieee80211_alloc_hw().
4482 * Drivers should use this function instead of netif_stop_queue.
4484 void ieee80211_stop_queues(struct ieee80211_hw *hw);
4487 * ieee80211_wake_queues - wake all queues
4488 * @hw: pointer as obtained from ieee80211_alloc_hw().
4490 * Drivers should use this function instead of netif_wake_queue.
4492 void ieee80211_wake_queues(struct ieee80211_hw *hw);
4495 * ieee80211_scan_completed - completed hardware scan
4497 * When hardware scan offload is used (i.e. the hw_scan() callback is
4498 * assigned) this function needs to be called by the driver to notify
4499 * mac80211 that the scan finished. This function can be called from
4500 * any context, including hardirq context.
4502 * @hw: the hardware that finished the scan
4503 * @aborted: set to true if scan was aborted
4505 void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted);
4508 * ieee80211_sched_scan_results - got results from scheduled scan
4510 * When a scheduled scan is running, this function needs to be called by the
4511 * driver whenever there are new scan results available.
4513 * @hw: the hardware that is performing scheduled scans
4515 void ieee80211_sched_scan_results(struct ieee80211_hw *hw);
4518 * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped
4520 * When a scheduled scan is running, this function can be called by
4521 * the driver if it needs to stop the scan to perform another task.
4522 * Usual scenarios are drivers that cannot continue the scheduled scan
4523 * while associating, for instance.
4525 * @hw: the hardware that is performing scheduled scans
4527 void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw);
4530 * enum ieee80211_interface_iteration_flags - interface iteration flags
4531 * @IEEE80211_IFACE_ITER_NORMAL: Iterate over all interfaces that have
4532 * been added to the driver; However, note that during hardware
4533 * reconfiguration (after restart_hw) it will iterate over a new
4534 * interface and over all the existing interfaces even if they
4535 * haven't been re-added to the driver yet.
4536 * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all
4537 * interfaces, even if they haven't been re-added to the driver yet.
4538 * @IEEE80211_IFACE_ITER_ACTIVE: Iterate only active interfaces (netdev is up).
4540 enum ieee80211_interface_iteration_flags {
4541 IEEE80211_IFACE_ITER_NORMAL = 0,
4542 IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0),
4543 IEEE80211_IFACE_ITER_ACTIVE = BIT(1),
4547 * ieee80211_iterate_interfaces - iterate interfaces
4549 * This function iterates over the interfaces associated with a given
4550 * hardware and calls the callback for them. This includes active as well as
4551 * inactive interfaces. This function allows the iterator function to sleep.
4552 * Will iterate over a new interface during add_interface().
4554 * @hw: the hardware struct of which the interfaces should be iterated over
4555 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
4556 * @iterator: the iterator function to call
4557 * @data: first argument of the iterator function
4559 void ieee80211_iterate_interfaces(struct ieee80211_hw *hw, u32 iter_flags,
4560 void (*iterator)(void *data, u8 *mac,
4561 struct ieee80211_vif *vif),
4565 * ieee80211_iterate_active_interfaces - iterate active interfaces
4567 * This function iterates over the interfaces associated with a given
4568 * hardware that are currently active and calls the callback for them.
4569 * This function allows the iterator function to sleep, when the iterator
4570 * function is atomic @ieee80211_iterate_active_interfaces_atomic can
4572 * Does not iterate over a new interface during add_interface().
4574 * @hw: the hardware struct of which the interfaces should be iterated over
4575 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
4576 * @iterator: the iterator function to call
4577 * @data: first argument of the iterator function
4580 ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, u32 iter_flags,
4581 void (*iterator)(void *data, u8 *mac,
4582 struct ieee80211_vif *vif),
4585 ieee80211_iterate_interfaces(hw,
4586 iter_flags | IEEE80211_IFACE_ITER_ACTIVE,
4591 * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
4593 * This function iterates over the interfaces associated with a given
4594 * hardware that are currently active and calls the callback for them.
4595 * This function requires the iterator callback function to be atomic,
4596 * if that is not desired, use @ieee80211_iterate_active_interfaces instead.
4597 * Does not iterate over a new interface during add_interface().
4599 * @hw: the hardware struct of which the interfaces should be iterated over
4600 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
4601 * @iterator: the iterator function to call, cannot sleep
4602 * @data: first argument of the iterator function
4604 void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
4606 void (*iterator)(void *data,
4608 struct ieee80211_vif *vif),
4612 * ieee80211_iterate_active_interfaces_rtnl - iterate active interfaces
4614 * This function iterates over the interfaces associated with a given
4615 * hardware that are currently active and calls the callback for them.
4616 * This version can only be used while holding the RTNL.
4618 * @hw: the hardware struct of which the interfaces should be iterated over
4619 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
4620 * @iterator: the iterator function to call, cannot sleep
4621 * @data: first argument of the iterator function
4623 void ieee80211_iterate_active_interfaces_rtnl(struct ieee80211_hw *hw,
4625 void (*iterator)(void *data,
4627 struct ieee80211_vif *vif),
4631 * ieee80211_iterate_stations_atomic - iterate stations
4633 * This function iterates over all stations associated with a given
4634 * hardware that are currently uploaded to the driver and calls the callback
4635 * function for them.
4636 * This function requires the iterator callback function to be atomic,
4638 * @hw: the hardware struct of which the interfaces should be iterated over
4639 * @iterator: the iterator function to call, cannot sleep
4640 * @data: first argument of the iterator function
4642 void ieee80211_iterate_stations_atomic(struct ieee80211_hw *hw,
4643 void (*iterator)(void *data,
4644 struct ieee80211_sta *sta),
4647 * ieee80211_queue_work - add work onto the mac80211 workqueue
4649 * Drivers and mac80211 use this to add work onto the mac80211 workqueue.
4650 * This helper ensures drivers are not queueing work when they should not be.
4652 * @hw: the hardware struct for the interface we are adding work for
4653 * @work: the work we want to add onto the mac80211 workqueue
4655 void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work);
4658 * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue
4660 * Drivers and mac80211 use this to queue delayed work onto the mac80211
4663 * @hw: the hardware struct for the interface we are adding work for
4664 * @dwork: delayable work to queue onto the mac80211 workqueue
4665 * @delay: number of jiffies to wait before queueing
4667 void ieee80211_queue_delayed_work(struct ieee80211_hw *hw,
4668 struct delayed_work *dwork,
4669 unsigned long delay);
4672 * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
4673 * @sta: the station for which to start a BA session
4674 * @tid: the TID to BA on.
4675 * @timeout: session timeout value (in TUs)
4677 * Return: success if addBA request was sent, failure otherwise
4679 * Although mac80211/low level driver/user space application can estimate
4680 * the need to start aggregation on a certain RA/TID, the session level
4681 * will be managed by the mac80211.
4683 int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid,
4687 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
4688 * @vif: &struct ieee80211_vif pointer from the add_interface callback
4689 * @ra: receiver address of the BA session recipient.
4690 * @tid: the TID to BA on.
4692 * This function must be called by low level driver once it has
4693 * finished with preparations for the BA session. It can be called
4696 void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
4700 * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
4701 * @sta: the station whose BA session to stop
4702 * @tid: the TID to stop BA.
4704 * Return: negative error if the TID is invalid, or no aggregation active
4706 * Although mac80211/low level driver/user space application can estimate
4707 * the need to stop aggregation on a certain RA/TID, the session level
4708 * will be managed by the mac80211.
4710 int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid);
4713 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
4714 * @vif: &struct ieee80211_vif pointer from the add_interface callback
4715 * @ra: receiver address of the BA session recipient.
4716 * @tid: the desired TID to BA on.
4718 * This function must be called by low level driver once it has
4719 * finished with preparations for the BA session tear down. It
4720 * can be called from any context.
4722 void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
4726 * ieee80211_find_sta - find a station
4728 * @vif: virtual interface to look for station on
4729 * @addr: station's address
4731 * Return: The station, if found. %NULL otherwise.
4733 * Note: This function must be called under RCU lock and the
4734 * resulting pointer is only valid under RCU lock as well.
4736 struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif,
4740 * ieee80211_find_sta_by_ifaddr - find a station on hardware
4742 * @hw: pointer as obtained from ieee80211_alloc_hw()
4743 * @addr: remote station's address
4744 * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'.
4746 * Return: The station, if found. %NULL otherwise.
4748 * Note: This function must be called under RCU lock and the
4749 * resulting pointer is only valid under RCU lock as well.
4751 * NOTE: You may pass NULL for localaddr, but then you will just get
4752 * the first STA that matches the remote address 'addr'.
4753 * We can have multiple STA associated with multiple
4754 * logical stations (e.g. consider a station connecting to another
4755 * BSSID on the same AP hardware without disconnecting first).
4756 * In this case, the result of this method with localaddr NULL
4759 * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible.
4761 struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw,
4763 const u8 *localaddr);
4766 * ieee80211_sta_block_awake - block station from waking up
4768 * @pubsta: the station
4769 * @block: whether to block or unblock
4771 * Some devices require that all frames that are on the queues
4772 * for a specific station that went to sleep are flushed before
4773 * a poll response or frames after the station woke up can be
4774 * delivered to that it. Note that such frames must be rejected
4775 * by the driver as filtered, with the appropriate status flag.
4777 * This function allows implementing this mode in a race-free
4780 * To do this, a driver must keep track of the number of frames
4781 * still enqueued for a specific station. If this number is not
4782 * zero when the station goes to sleep, the driver must call
4783 * this function to force mac80211 to consider the station to
4784 * be asleep regardless of the station's actual state. Once the
4785 * number of outstanding frames reaches zero, the driver must
4786 * call this function again to unblock the station. That will
4787 * cause mac80211 to be able to send ps-poll responses, and if
4788 * the station queried in the meantime then frames will also
4789 * be sent out as a result of this. Additionally, the driver
4790 * will be notified that the station woke up some time after
4791 * it is unblocked, regardless of whether the station actually
4792 * woke up while blocked or not.
4794 void ieee80211_sta_block_awake(struct ieee80211_hw *hw,
4795 struct ieee80211_sta *pubsta, bool block);
4798 * ieee80211_sta_eosp - notify mac80211 about end of SP
4799 * @pubsta: the station
4801 * When a device transmits frames in a way that it can't tell
4802 * mac80211 in the TX status about the EOSP, it must clear the
4803 * %IEEE80211_TX_STATUS_EOSP bit and call this function instead.
4804 * This applies for PS-Poll as well as uAPSD.
4806 * Note that just like with _tx_status() and _rx() drivers must
4807 * not mix calls to irqsafe/non-irqsafe versions, this function
4808 * must not be mixed with those either. Use the all irqsafe, or
4809 * all non-irqsafe, don't mix!
4811 * NB: the _irqsafe version of this function doesn't exist, no
4812 * driver needs it right now. Don't call this function if
4813 * you'd need the _irqsafe version, look at the git history
4814 * and restore the _irqsafe version!
4816 void ieee80211_sta_eosp(struct ieee80211_sta *pubsta);
4819 * ieee80211_iter_keys - iterate keys programmed into the device
4820 * @hw: pointer obtained from ieee80211_alloc_hw()
4821 * @vif: virtual interface to iterate, may be %NULL for all
4822 * @iter: iterator function that will be called for each key
4823 * @iter_data: custom data to pass to the iterator function
4825 * This function can be used to iterate all the keys known to
4826 * mac80211, even those that weren't previously programmed into
4827 * the device. This is intended for use in WoWLAN if the device
4828 * needs reprogramming of the keys during suspend. Note that due
4829 * to locking reasons, it is also only safe to call this at few
4830 * spots since it must hold the RTNL and be able to sleep.
4832 * The order in which the keys are iterated matches the order
4833 * in which they were originally installed and handed to the
4836 void ieee80211_iter_keys(struct ieee80211_hw *hw,
4837 struct ieee80211_vif *vif,
4838 void (*iter)(struct ieee80211_hw *hw,
4839 struct ieee80211_vif *vif,
4840 struct ieee80211_sta *sta,
4841 struct ieee80211_key_conf *key,
4846 * ieee80211_iter_chan_contexts_atomic - iterate channel contexts
4847 * @hw: pointre obtained from ieee80211_alloc_hw().
4848 * @iter: iterator function
4849 * @iter_data: data passed to iterator function
4851 * Iterate all active channel contexts. This function is atomic and
4852 * doesn't acquire any locks internally that might be held in other
4853 * places while calling into the driver.
4855 * The iterator will not find a context that's being added (during
4856 * the driver callback to add it) but will find it while it's being
4859 * Note that during hardware restart, all contexts that existed
4860 * before the restart are considered already present so will be
4861 * found while iterating, whether they've been re-added already
4864 void ieee80211_iter_chan_contexts_atomic(
4865 struct ieee80211_hw *hw,
4866 void (*iter)(struct ieee80211_hw *hw,
4867 struct ieee80211_chanctx_conf *chanctx_conf,
4872 * ieee80211_ap_probereq_get - retrieve a Probe Request template
4873 * @hw: pointer obtained from ieee80211_alloc_hw().
4874 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4876 * Creates a Probe Request template which can, for example, be uploaded to
4877 * hardware. The template is filled with bssid, ssid and supported rate
4878 * information. This function must only be called from within the
4879 * .bss_info_changed callback function and only in managed mode. The function
4880 * is only useful when the interface is associated, otherwise it will return
4883 * Return: The Probe Request template. %NULL on error.
4885 struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw,
4886 struct ieee80211_vif *vif);
4889 * ieee80211_beacon_loss - inform hardware does not receive beacons
4891 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4893 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and
4894 * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the
4895 * hardware is not receiving beacons with this function.
4897 void ieee80211_beacon_loss(struct ieee80211_vif *vif);
4900 * ieee80211_connection_loss - inform hardware has lost connection to the AP
4902 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4904 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and
4905 * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver
4906 * needs to inform if the connection to the AP has been lost.
4907 * The function may also be called if the connection needs to be terminated
4908 * for some other reason, even if %IEEE80211_HW_CONNECTION_MONITOR isn't set.
4910 * This function will cause immediate change to disassociated state,
4911 * without connection recovery attempts.
4913 void ieee80211_connection_loss(struct ieee80211_vif *vif);
4916 * ieee80211_resume_disconnect - disconnect from AP after resume
4918 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4920 * Instructs mac80211 to disconnect from the AP after resume.
4921 * Drivers can use this after WoWLAN if they know that the
4922 * connection cannot be kept up, for example because keys were
4923 * used while the device was asleep but the replay counters or
4924 * similar cannot be retrieved from the device during resume.
4926 * Note that due to implementation issues, if the driver uses
4927 * the reconfiguration functionality during resume the interface
4928 * will still be added as associated first during resume and then
4929 * disconnect normally later.
4931 * This function can only be called from the resume callback and
4932 * the driver must not be holding any of its own locks while it
4933 * calls this function, or at least not any locks it needs in the
4934 * key configuration paths (if it supports HW crypto).
4936 void ieee80211_resume_disconnect(struct ieee80211_vif *vif);
4939 * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
4940 * rssi threshold triggered
4942 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4943 * @rssi_event: the RSSI trigger event type
4944 * @gfp: context flags
4946 * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality
4947 * monitoring is configured with an rssi threshold, the driver will inform
4948 * whenever the rssi level reaches the threshold.
4950 void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif,
4951 enum nl80211_cqm_rssi_threshold_event rssi_event,
4955 * ieee80211_cqm_beacon_loss_notify - inform CQM of beacon loss
4957 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4958 * @gfp: context flags
4960 void ieee80211_cqm_beacon_loss_notify(struct ieee80211_vif *vif, gfp_t gfp);
4963 * ieee80211_radar_detected - inform that a radar was detected
4965 * @hw: pointer as obtained from ieee80211_alloc_hw()
4967 void ieee80211_radar_detected(struct ieee80211_hw *hw);
4970 * ieee80211_chswitch_done - Complete channel switch process
4971 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4972 * @success: make the channel switch successful or not
4974 * Complete the channel switch post-process: set the new operational channel
4975 * and wake up the suspended queues.
4977 void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success);
4980 * ieee80211_request_smps - request SM PS transition
4981 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4982 * @smps_mode: new SM PS mode
4984 * This allows the driver to request an SM PS transition in managed
4985 * mode. This is useful when the driver has more information than
4986 * the stack about possible interference, for example by bluetooth.
4988 void ieee80211_request_smps(struct ieee80211_vif *vif,
4989 enum ieee80211_smps_mode smps_mode);
4992 * ieee80211_ready_on_channel - notification of remain-on-channel start
4993 * @hw: pointer as obtained from ieee80211_alloc_hw()
4995 void ieee80211_ready_on_channel(struct ieee80211_hw *hw);
4998 * ieee80211_remain_on_channel_expired - remain_on_channel duration expired
4999 * @hw: pointer as obtained from ieee80211_alloc_hw()
5001 void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw);
5004 * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions
5006 * in order not to harm the system performance and user experience, the device
5007 * may request not to allow any rx ba session and tear down existing rx ba
5008 * sessions based on system constraints such as periodic BT activity that needs
5009 * to limit wlan activity (eg.sco or a2dp)."
5010 * in such cases, the intention is to limit the duration of the rx ppdu and
5011 * therefore prevent the peer device to use a-mpdu aggregation.
5013 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5014 * @ba_rx_bitmap: Bit map of open rx ba per tid
5015 * @addr: & to bssid mac address
5017 void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap,
5021 * ieee80211_send_bar - send a BlockAckReq frame
5023 * can be used to flush pending frames from the peer's aggregation reorder
5026 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5027 * @ra: the peer's destination address
5028 * @tid: the TID of the aggregation session
5029 * @ssn: the new starting sequence number for the receiver
5031 void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn);
5034 * ieee80211_start_rx_ba_session_offl - start a Rx BA session
5036 * Some device drivers may offload part of the Rx aggregation flow including
5037 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx
5040 * Create structures responsible for reordering so device drivers may call here
5041 * when they complete AddBa negotiation.
5043 * @vif: &struct ieee80211_vif pointer from the add_interface callback
5044 * @addr: station mac address
5047 void ieee80211_start_rx_ba_session_offl(struct ieee80211_vif *vif,
5048 const u8 *addr, u16 tid);
5051 * ieee80211_stop_rx_ba_session_offl - stop a Rx BA session
5053 * Some device drivers may offload part of the Rx aggregation flow including
5054 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx
5057 * Destroy structures responsible for reordering so device drivers may call here
5058 * when they complete DelBa negotiation.
5060 * @vif: &struct ieee80211_vif pointer from the add_interface callback
5061 * @addr: station mac address
5064 void ieee80211_stop_rx_ba_session_offl(struct ieee80211_vif *vif,
5065 const u8 *addr, u16 tid);
5067 /* Rate control API */
5070 * struct ieee80211_tx_rate_control - rate control information for/from RC algo
5072 * @hw: The hardware the algorithm is invoked for.
5073 * @sband: The band this frame is being transmitted on.
5074 * @bss_conf: the current BSS configuration
5075 * @skb: the skb that will be transmitted, the control information in it needs
5077 * @reported_rate: The rate control algorithm can fill this in to indicate
5078 * which rate should be reported to userspace as the current rate and
5079 * used for rate calculations in the mesh network.
5080 * @rts: whether RTS will be used for this frame because it is longer than the
5082 * @short_preamble: whether mac80211 will request short-preamble transmission
5083 * if the selected rate supports it
5084 * @max_rate_idx: user-requested maximum (legacy) rate
5085 * (deprecated; this will be removed once drivers get updated to use
5087 * @rate_idx_mask: user-requested (legacy) rate mask
5088 * @rate_idx_mcs_mask: user-requested MCS rate mask (NULL if not in use)
5089 * @bss: whether this frame is sent out in AP or IBSS mode
5091 struct ieee80211_tx_rate_control {
5092 struct ieee80211_hw *hw;
5093 struct ieee80211_supported_band *sband;
5094 struct ieee80211_bss_conf *bss_conf;
5095 struct sk_buff *skb;
5096 struct ieee80211_tx_rate reported_rate;
5097 bool rts, short_preamble;
5100 u8 *rate_idx_mcs_mask;
5104 struct rate_control_ops {
5106 void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir);
5107 void (*free)(void *priv);
5109 void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
5110 void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
5111 struct cfg80211_chan_def *chandef,
5112 struct ieee80211_sta *sta, void *priv_sta);
5113 void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
5114 struct cfg80211_chan_def *chandef,
5115 struct ieee80211_sta *sta, void *priv_sta,
5117 void (*free_sta)(void *priv, struct ieee80211_sta *sta,
5120 void (*tx_status_noskb)(void *priv,
5121 struct ieee80211_supported_band *sband,
5122 struct ieee80211_sta *sta, void *priv_sta,
5123 struct ieee80211_tx_info *info);
5124 void (*tx_status)(void *priv, struct ieee80211_supported_band *sband,
5125 struct ieee80211_sta *sta, void *priv_sta,
5126 struct sk_buff *skb);
5127 void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta,
5128 struct ieee80211_tx_rate_control *txrc);
5130 void (*add_sta_debugfs)(void *priv, void *priv_sta,
5131 struct dentry *dir);
5132 void (*remove_sta_debugfs)(void *priv, void *priv_sta);
5134 u32 (*get_expected_throughput)(void *priv_sta);
5137 static inline int rate_supported(struct ieee80211_sta *sta,
5138 enum ieee80211_band band,
5141 return (sta == NULL || sta->supp_rates[band] & BIT(index));
5145 * rate_control_send_low - helper for drivers for management/no-ack frames
5147 * Rate control algorithms that agree to use the lowest rate to
5148 * send management frames and NO_ACK data with the respective hw
5149 * retries should use this in the beginning of their mac80211 get_rate
5150 * callback. If true is returned the rate control can simply return.
5151 * If false is returned we guarantee that sta and sta and priv_sta is
5154 * Rate control algorithms wishing to do more intelligent selection of
5155 * rate for multicast/broadcast frames may choose to not use this.
5157 * @sta: &struct ieee80211_sta pointer to the target destination. Note
5158 * that this may be null.
5159 * @priv_sta: private rate control structure. This may be null.
5160 * @txrc: rate control information we sholud populate for mac80211.
5162 bool rate_control_send_low(struct ieee80211_sta *sta,
5164 struct ieee80211_tx_rate_control *txrc);
5168 rate_lowest_index(struct ieee80211_supported_band *sband,
5169 struct ieee80211_sta *sta)
5173 for (i = 0; i < sband->n_bitrates; i++)
5174 if (rate_supported(sta, sband->band, i))
5177 /* warn when we cannot find a rate. */
5180 /* and return 0 (the lowest index) */
5185 bool rate_usable_index_exists(struct ieee80211_supported_band *sband,
5186 struct ieee80211_sta *sta)
5190 for (i = 0; i < sband->n_bitrates; i++)
5191 if (rate_supported(sta, sband->band, i))
5197 * rate_control_set_rates - pass the sta rate selection to mac80211/driver
5199 * When not doing a rate control probe to test rates, rate control should pass
5200 * its rate selection to mac80211. If the driver supports receiving a station
5201 * rate table, it will use it to ensure that frames are always sent based on
5202 * the most recent rate control module decision.
5204 * @hw: pointer as obtained from ieee80211_alloc_hw()
5205 * @pubsta: &struct ieee80211_sta pointer to the target destination.
5206 * @rates: new tx rate set to be used for this station.
5208 int rate_control_set_rates(struct ieee80211_hw *hw,
5209 struct ieee80211_sta *pubsta,
5210 struct ieee80211_sta_rates *rates);
5212 int ieee80211_rate_control_register(const struct rate_control_ops *ops);
5213 void ieee80211_rate_control_unregister(const struct rate_control_ops *ops);
5216 conf_is_ht20(struct ieee80211_conf *conf)
5218 return conf->chandef.width == NL80211_CHAN_WIDTH_20;
5222 conf_is_ht40_minus(struct ieee80211_conf *conf)
5224 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
5225 conf->chandef.center_freq1 < conf->chandef.chan->center_freq;
5229 conf_is_ht40_plus(struct ieee80211_conf *conf)
5231 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
5232 conf->chandef.center_freq1 > conf->chandef.chan->center_freq;
5236 conf_is_ht40(struct ieee80211_conf *conf)
5238 return conf->chandef.width == NL80211_CHAN_WIDTH_40;
5242 conf_is_ht(struct ieee80211_conf *conf)
5244 return (conf->chandef.width != NL80211_CHAN_WIDTH_5) &&
5245 (conf->chandef.width != NL80211_CHAN_WIDTH_10) &&
5246 (conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT);
5249 static inline enum nl80211_iftype
5250 ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p)
5254 case NL80211_IFTYPE_STATION:
5255 return NL80211_IFTYPE_P2P_CLIENT;
5256 case NL80211_IFTYPE_AP:
5257 return NL80211_IFTYPE_P2P_GO;
5265 static inline enum nl80211_iftype
5266 ieee80211_vif_type_p2p(struct ieee80211_vif *vif)
5268 return ieee80211_iftype_p2p(vif->type, vif->p2p);
5271 void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif,
5273 int rssi_max_thold);
5275 void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif);
5278 * ieee80211_ave_rssi - report the average RSSI for the specified interface
5280 * @vif: the specified virtual interface
5282 * Note: This function assumes that the given vif is valid.
5284 * Return: The average RSSI value for the requested interface, or 0 if not
5287 int ieee80211_ave_rssi(struct ieee80211_vif *vif);
5290 * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup
5291 * @vif: virtual interface
5292 * @wakeup: wakeup reason(s)
5293 * @gfp: allocation flags
5295 * See cfg80211_report_wowlan_wakeup().
5297 void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif,
5298 struct cfg80211_wowlan_wakeup *wakeup,
5302 * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission
5303 * @hw: pointer as obtained from ieee80211_alloc_hw()
5304 * @vif: virtual interface
5305 * @skb: frame to be sent from within the driver
5306 * @band: the band to transmit on
5307 * @sta: optional pointer to get the station to send the frame to
5309 * Note: must be called under RCU lock
5311 bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw,
5312 struct ieee80211_vif *vif, struct sk_buff *skb,
5313 int band, struct ieee80211_sta **sta);
5316 * struct ieee80211_noa_data - holds temporary data for tracking P2P NoA state
5318 * @next_tsf: TSF timestamp of the next absent state change
5319 * @has_next_tsf: next absent state change event pending
5321 * @absent: descriptor bitmask, set if GO is currently absent
5325 * @count: count fields from the NoA descriptors
5326 * @desc: adjusted data from the NoA
5328 struct ieee80211_noa_data {
5334 u8 count[IEEE80211_P2P_NOA_DESC_MAX];
5339 } desc[IEEE80211_P2P_NOA_DESC_MAX];
5343 * ieee80211_parse_p2p_noa - initialize NoA tracking data from P2P IE
5346 * @data: NoA tracking data
5347 * @tsf: current TSF timestamp
5349 * Return: number of successfully parsed descriptors
5351 int ieee80211_parse_p2p_noa(const struct ieee80211_p2p_noa_attr *attr,
5352 struct ieee80211_noa_data *data, u32 tsf);
5355 * ieee80211_update_p2p_noa - get next pending P2P GO absent state change
5357 * @data: NoA tracking data
5358 * @tsf: current TSF timestamp
5360 void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf);
5363 * ieee80211_tdls_oper - request userspace to perform a TDLS operation
5364 * @vif: virtual interface
5365 * @peer: the peer's destination address
5366 * @oper: the requested TDLS operation
5367 * @reason_code: reason code for the operation, valid for TDLS teardown
5368 * @gfp: allocation flags
5370 * See cfg80211_tdls_oper_request().
5372 void ieee80211_tdls_oper_request(struct ieee80211_vif *vif, const u8 *peer,
5373 enum nl80211_tdls_operation oper,
5374 u16 reason_code, gfp_t gfp);
5377 * ieee80211_reserve_tid - request to reserve a specific TID
5379 * There is sometimes a need (such as in TDLS) for blocking the driver from
5380 * using a specific TID so that the FW can use it for certain operations such
5381 * as sending PTI requests. To make sure that the driver doesn't use that TID,
5382 * this function must be called as it flushes out packets on this TID and marks
5383 * it as blocked, so that any transmit for the station on this TID will be
5384 * redirected to the alternative TID in the same AC.
5386 * Note that this function blocks and may call back into the driver, so it
5387 * should be called without driver locks held. Also note this function should
5388 * only be called from the driver's @sta_state callback.
5390 * @sta: the station to reserve the TID for
5391 * @tid: the TID to reserve
5393 * Returns: 0 on success, else on failure
5395 int ieee80211_reserve_tid(struct ieee80211_sta *sta, u8 tid);
5398 * ieee80211_unreserve_tid - request to unreserve a specific TID
5400 * Once there is no longer any need for reserving a certain TID, this function
5401 * should be called, and no longer will packets have their TID modified for
5402 * preventing use of this TID in the driver.
5404 * Note that this function blocks and acquires a lock, so it should be called
5405 * without driver locks held. Also note this function should only be called
5406 * from the driver's @sta_state callback.
5409 * @tid: the TID to unreserve
5411 void ieee80211_unreserve_tid(struct ieee80211_sta *sta, u8 tid);
5414 * ieee80211_tx_dequeue - dequeue a packet from a software tx queue
5416 * @hw: pointer as obtained from ieee80211_alloc_hw()
5417 * @txq: pointer obtained from station or virtual interface
5419 * Returns the skb if successful, %NULL if no frame was available.
5421 struct sk_buff *ieee80211_tx_dequeue(struct ieee80211_hw *hw,
5422 struct ieee80211_txq *txq);
5423 #endif /* MAC80211_H */