2 * mxser.c -- MOXA Smartio/Industio family multiport serial driver.
4 * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com).
5 * Copyright (C) 2006-2008 Jiri Slaby <jirislaby@gmail.com>
7 * This code is loosely based on the 1.8 moxa driver which is based on
8 * Linux serial driver, written by Linus Torvalds, Theodore T'so and
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License, or
14 * (at your option) any later version.
16 * Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox
17 * <alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on
19 * - Fixed x86_64 cleanness
22 #include <linux/module.h>
23 #include <linux/errno.h>
24 #include <linux/signal.h>
25 #include <linux/sched.h>
26 #include <linux/timer.h>
27 #include <linux/interrupt.h>
28 #include <linux/tty.h>
29 #include <linux/tty_flip.h>
30 #include <linux/serial.h>
31 #include <linux/serial_reg.h>
32 #include <linux/major.h>
33 #include <linux/string.h>
34 #include <linux/fcntl.h>
35 #include <linux/ptrace.h>
36 #include <linux/ioport.h>
38 #include <linux/delay.h>
39 #include <linux/pci.h>
40 #include <linux/bitops.h>
41 #include <linux/slab.h>
42 #include <linux/ratelimit.h>
46 #include <asm/uaccess.h>
50 #define MXSER_VERSION "2.0.5" /* 1.14 */
51 #define MXSERMAJOR 174
53 #define MXSER_BOARDS 4 /* Max. boards */
54 #define MXSER_PORTS_PER_BOARD 8 /* Max. ports per board */
55 #define MXSER_PORTS (MXSER_BOARDS * MXSER_PORTS_PER_BOARD)
56 #define MXSER_ISR_PASS_LIMIT 100
58 /*CheckIsMoxaMust return value*/
59 #define MOXA_OTHER_UART 0x00
60 #define MOXA_MUST_MU150_HWID 0x01
61 #define MOXA_MUST_MU860_HWID 0x02
63 #define WAKEUP_CHARS 256
65 #define UART_MCR_AFE 0x20
66 #define UART_LSR_SPECIAL 0x1E
68 #define PCI_DEVICE_ID_POS104UL 0x1044
69 #define PCI_DEVICE_ID_CB108 0x1080
70 #define PCI_DEVICE_ID_CP102UF 0x1023
71 #define PCI_DEVICE_ID_CP112UL 0x1120
72 #define PCI_DEVICE_ID_CB114 0x1142
73 #define PCI_DEVICE_ID_CP114UL 0x1143
74 #define PCI_DEVICE_ID_CB134I 0x1341
75 #define PCI_DEVICE_ID_CP138U 0x1380
78 #define C168_ASIC_ID 1
79 #define C104_ASIC_ID 2
80 #define C102_ASIC_ID 0xB
81 #define CI132_ASIC_ID 4
82 #define CI134_ASIC_ID 3
83 #define CI104J_ASIC_ID 5
85 #define MXSER_HIGHBAUD 1
88 /* This is only for PCI */
98 } Gpci_uart_info[] = {
99 {MOXA_OTHER_UART, 16, 16, 16, 14, 14, 1, 921600L},
100 {MOXA_MUST_MU150_HWID, 64, 64, 64, 48, 48, 16, 230400L},
101 {MOXA_MUST_MU860_HWID, 128, 128, 128, 96, 96, 32, 921600L}
103 #define UART_INFO_NUM ARRAY_SIZE(Gpci_uart_info)
105 struct mxser_cardinfo {
111 static const struct mxser_cardinfo mxser_cards[] = {
112 /* 0*/ { "C168 series", 8, },
113 { "C104 series", 4, },
114 { "CI-104J series", 4, },
115 { "C168H/PCI series", 8, },
116 { "C104H/PCI series", 4, },
117 /* 5*/ { "C102 series", 4, MXSER_HAS2 }, /* C102-ISA */
118 { "CI-132 series", 4, MXSER_HAS2 },
119 { "CI-134 series", 4, },
120 { "CP-132 series", 2, },
121 { "CP-114 series", 4, },
122 /*10*/ { "CT-114 series", 4, },
123 { "CP-102 series", 2, MXSER_HIGHBAUD },
124 { "CP-104U series", 4, },
125 { "CP-168U series", 8, },
126 { "CP-132U series", 2, },
127 /*15*/ { "CP-134U series", 4, },
128 { "CP-104JU series", 4, },
129 { "Moxa UC7000 Serial", 8, }, /* RC7000 */
130 { "CP-118U series", 8, },
131 { "CP-102UL series", 2, },
132 /*20*/ { "CP-102U series", 2, },
133 { "CP-118EL series", 8, },
134 { "CP-168EL series", 8, },
135 { "CP-104EL series", 4, },
136 { "CB-108 series", 8, },
137 /*25*/ { "CB-114 series", 4, },
138 { "CB-134I series", 4, },
139 { "CP-138U series", 8, },
140 { "POS-104UL series", 4, },
141 { "CP-114UL series", 4, },
142 /*30*/ { "CP-102UF series", 2, },
143 { "CP-112UL series", 2, },
146 /* driver_data correspond to the lines in the structure above
147 see also ISA probe function before you change something */
148 static struct pci_device_id mxser_pcibrds[] = {
149 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C168), .driver_data = 3 },
150 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C104), .driver_data = 4 },
151 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132), .driver_data = 8 },
152 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP114), .driver_data = 9 },
153 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CT114), .driver_data = 10 },
154 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102), .driver_data = 11 },
155 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104U), .driver_data = 12 },
156 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168U), .driver_data = 13 },
157 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132U), .driver_data = 14 },
158 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP134U), .driver_data = 15 },
159 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104JU),.driver_data = 16 },
160 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_RC7000), .driver_data = 17 },
161 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118U), .driver_data = 18 },
162 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102UL),.driver_data = 19 },
163 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102U), .driver_data = 20 },
164 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118EL),.driver_data = 21 },
165 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168EL),.driver_data = 22 },
166 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104EL),.driver_data = 23 },
167 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB108), .driver_data = 24 },
168 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB114), .driver_data = 25 },
169 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB134I), .driver_data = 26 },
170 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138U), .driver_data = 27 },
171 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL), .driver_data = 28 },
172 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP114UL), .driver_data = 29 },
173 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP102UF), .driver_data = 30 },
174 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP112UL), .driver_data = 31 },
177 MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
179 static unsigned long ioaddr[MXSER_BOARDS];
180 static int ttymajor = MXSERMAJOR;
182 /* Variables for insmod */
184 MODULE_AUTHOR("Casper Yang");
185 MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver");
186 module_param_array(ioaddr, ulong, NULL, 0);
187 MODULE_PARM_DESC(ioaddr, "ISA io addresses to look for a moxa board");
188 module_param(ttymajor, int, 0);
189 MODULE_LICENSE("GPL");
193 unsigned long rxcnt[MXSER_PORTS];
194 unsigned long txcnt[MXSER_PORTS];
200 unsigned long up_rxcnt;
201 unsigned long up_txcnt;
203 unsigned char hold_reason;
206 struct mxser_mon_ext {
207 unsigned long rx_cnt[32];
208 unsigned long tx_cnt[32];
209 unsigned long up_rxcnt[32];
210 unsigned long up_txcnt[32];
211 int modem_status[32];
225 struct tty_port port;
226 struct mxser_board *board;
228 unsigned long ioaddr;
229 unsigned long opmode_ioaddr;
233 int rx_trigger; /* Rx fifo trigger level */
235 int baud_base; /* max. speed */
236 int type; /* UART type */
238 int x_char; /* xon/xoff character */
239 int IER; /* Interrupt Enable Register */
240 int MCR; /* Modem control register */
242 unsigned char stop_rx;
243 unsigned char ldisc_stop_rx;
246 unsigned char err_shadow;
248 struct async_icount icount; /* kernel counters for 4 input interrupts */
251 int read_status_mask;
252 int ignore_status_mask;
258 struct ktermios normal_termios;
260 struct mxser_mon mon_data;
268 const struct mxser_cardinfo *info;
269 unsigned long vector;
270 unsigned long vector_mask;
275 struct mxser_port ports[MXSER_PORTS_PER_BOARD];
278 struct mxser_mstatus {
286 static struct mxser_board mxser_boards[MXSER_BOARDS];
287 static struct tty_driver *mxvar_sdriver;
288 static struct mxser_log mxvar_log;
289 static int mxser_set_baud_method[MXSER_PORTS + 1];
291 static void mxser_enable_must_enchance_mode(unsigned long baseio)
296 oldlcr = inb(baseio + UART_LCR);
297 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
299 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
300 efr |= MOXA_MUST_EFR_EFRB_ENABLE;
302 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
303 outb(oldlcr, baseio + UART_LCR);
307 static void mxser_disable_must_enchance_mode(unsigned long baseio)
312 oldlcr = inb(baseio + UART_LCR);
313 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
315 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
316 efr &= ~MOXA_MUST_EFR_EFRB_ENABLE;
318 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
319 outb(oldlcr, baseio + UART_LCR);
323 static void mxser_set_must_xon1_value(unsigned long baseio, u8 value)
328 oldlcr = inb(baseio + UART_LCR);
329 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
331 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
332 efr &= ~MOXA_MUST_EFR_BANK_MASK;
333 efr |= MOXA_MUST_EFR_BANK0;
335 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
336 outb(value, baseio + MOXA_MUST_XON1_REGISTER);
337 outb(oldlcr, baseio + UART_LCR);
340 static void mxser_set_must_xoff1_value(unsigned long baseio, u8 value)
345 oldlcr = inb(baseio + UART_LCR);
346 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
348 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
349 efr &= ~MOXA_MUST_EFR_BANK_MASK;
350 efr |= MOXA_MUST_EFR_BANK0;
352 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
353 outb(value, baseio + MOXA_MUST_XOFF1_REGISTER);
354 outb(oldlcr, baseio + UART_LCR);
357 static void mxser_set_must_fifo_value(struct mxser_port *info)
362 oldlcr = inb(info->ioaddr + UART_LCR);
363 outb(MOXA_MUST_ENTER_ENCHANCE, info->ioaddr + UART_LCR);
365 efr = inb(info->ioaddr + MOXA_MUST_EFR_REGISTER);
366 efr &= ~MOXA_MUST_EFR_BANK_MASK;
367 efr |= MOXA_MUST_EFR_BANK1;
369 outb(efr, info->ioaddr + MOXA_MUST_EFR_REGISTER);
370 outb((u8)info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTH_REGISTER);
371 outb((u8)info->rx_trigger, info->ioaddr + MOXA_MUST_RBRTI_REGISTER);
372 outb((u8)info->rx_low_water, info->ioaddr + MOXA_MUST_RBRTL_REGISTER);
373 outb(oldlcr, info->ioaddr + UART_LCR);
376 static void mxser_set_must_enum_value(unsigned long baseio, u8 value)
381 oldlcr = inb(baseio + UART_LCR);
382 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
384 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
385 efr &= ~MOXA_MUST_EFR_BANK_MASK;
386 efr |= MOXA_MUST_EFR_BANK2;
388 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
389 outb(value, baseio + MOXA_MUST_ENUM_REGISTER);
390 outb(oldlcr, baseio + UART_LCR);
394 static void mxser_get_must_hardware_id(unsigned long baseio, u8 *pId)
399 oldlcr = inb(baseio + UART_LCR);
400 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
402 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
403 efr &= ~MOXA_MUST_EFR_BANK_MASK;
404 efr |= MOXA_MUST_EFR_BANK2;
406 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
407 *pId = inb(baseio + MOXA_MUST_HWID_REGISTER);
408 outb(oldlcr, baseio + UART_LCR);
412 static void SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(unsigned long baseio)
417 oldlcr = inb(baseio + UART_LCR);
418 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
420 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
421 efr &= ~MOXA_MUST_EFR_SF_MASK;
423 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
424 outb(oldlcr, baseio + UART_LCR);
427 static void mxser_enable_must_tx_software_flow_control(unsigned long baseio)
432 oldlcr = inb(baseio + UART_LCR);
433 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
435 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
436 efr &= ~MOXA_MUST_EFR_SF_TX_MASK;
437 efr |= MOXA_MUST_EFR_SF_TX1;
439 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
440 outb(oldlcr, baseio + UART_LCR);
443 static void mxser_disable_must_tx_software_flow_control(unsigned long baseio)
448 oldlcr = inb(baseio + UART_LCR);
449 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
451 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
452 efr &= ~MOXA_MUST_EFR_SF_TX_MASK;
454 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
455 outb(oldlcr, baseio + UART_LCR);
458 static void mxser_enable_must_rx_software_flow_control(unsigned long baseio)
463 oldlcr = inb(baseio + UART_LCR);
464 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
466 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
467 efr &= ~MOXA_MUST_EFR_SF_RX_MASK;
468 efr |= MOXA_MUST_EFR_SF_RX1;
470 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
471 outb(oldlcr, baseio + UART_LCR);
474 static void mxser_disable_must_rx_software_flow_control(unsigned long baseio)
479 oldlcr = inb(baseio + UART_LCR);
480 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
482 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
483 efr &= ~MOXA_MUST_EFR_SF_RX_MASK;
485 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
486 outb(oldlcr, baseio + UART_LCR);
490 static int CheckIsMoxaMust(unsigned long io)
495 outb(0, io + UART_LCR);
496 mxser_disable_must_enchance_mode(io);
497 oldmcr = inb(io + UART_MCR);
498 outb(0, io + UART_MCR);
499 mxser_set_must_xon1_value(io, 0x11);
500 if ((hwid = inb(io + UART_MCR)) != 0) {
501 outb(oldmcr, io + UART_MCR);
502 return MOXA_OTHER_UART;
505 mxser_get_must_hardware_id(io, &hwid);
506 for (i = 1; i < UART_INFO_NUM; i++) { /* 0 = OTHER_UART */
507 if (hwid == Gpci_uart_info[i].type)
510 return MOXA_OTHER_UART;
514 static void process_txrx_fifo(struct mxser_port *info)
518 if ((info->type == PORT_16450) || (info->type == PORT_8250)) {
519 info->rx_trigger = 1;
520 info->rx_high_water = 1;
521 info->rx_low_water = 1;
522 info->xmit_fifo_size = 1;
524 for (i = 0; i < UART_INFO_NUM; i++)
525 if (info->board->chip_flag == Gpci_uart_info[i].type) {
526 info->rx_trigger = Gpci_uart_info[i].rx_trigger;
527 info->rx_low_water = Gpci_uart_info[i].rx_low_water;
528 info->rx_high_water = Gpci_uart_info[i].rx_high_water;
529 info->xmit_fifo_size = Gpci_uart_info[i].xmit_fifo_size;
534 static unsigned char mxser_get_msr(int baseaddr, int mode, int port)
536 static unsigned char mxser_msr[MXSER_PORTS + 1];
537 unsigned char status = 0;
539 status = inb(baseaddr + UART_MSR);
541 mxser_msr[port] &= 0x0F;
542 mxser_msr[port] |= status;
543 status = mxser_msr[port];
550 static int mxser_carrier_raised(struct tty_port *port)
552 struct mxser_port *mp = container_of(port, struct mxser_port, port);
553 return (inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD)?1:0;
556 static void mxser_dtr_rts(struct tty_port *port, int on)
558 struct mxser_port *mp = container_of(port, struct mxser_port, port);
561 spin_lock_irqsave(&mp->slock, flags);
563 outb(inb(mp->ioaddr + UART_MCR) |
564 UART_MCR_DTR | UART_MCR_RTS, mp->ioaddr + UART_MCR);
566 outb(inb(mp->ioaddr + UART_MCR)&~(UART_MCR_DTR | UART_MCR_RTS),
567 mp->ioaddr + UART_MCR);
568 spin_unlock_irqrestore(&mp->slock, flags);
571 static int mxser_set_baud(struct tty_struct *tty, long newspd)
573 struct mxser_port *info = tty->driver_data;
580 if (newspd > info->max_baud)
584 quot = 2 * info->baud_base / 269;
585 tty_encode_baud_rate(tty, 134, 134);
587 quot = info->baud_base / newspd;
590 baud = info->baud_base/quot;
591 tty_encode_baud_rate(tty, baud, baud);
596 info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base);
597 info->timeout += HZ / 50; /* Add .02 seconds of slop */
600 info->MCR |= UART_MCR_DTR;
601 outb(info->MCR, info->ioaddr + UART_MCR);
603 info->MCR &= ~UART_MCR_DTR;
604 outb(info->MCR, info->ioaddr + UART_MCR);
608 cval = inb(info->ioaddr + UART_LCR);
610 outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */
612 outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */
613 outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */
614 outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */
617 if (C_BAUD(tty) == BOTHER) {
618 quot = info->baud_base % newspd;
620 if (quot % newspd > newspd / 2) {
626 mxser_set_must_enum_value(info->ioaddr, quot);
629 mxser_set_must_enum_value(info->ioaddr, 0);
635 * This routine is called to set the UART divisor registers to match
636 * the specified baud rate for a serial port.
638 static int mxser_change_speed(struct tty_struct *tty,
639 struct ktermios *old_termios)
641 struct mxser_port *info = tty->driver_data;
642 unsigned cflag, cval, fcr;
644 unsigned char status;
646 cflag = tty->termios.c_cflag;
650 if (mxser_set_baud_method[tty->index] == 0)
651 mxser_set_baud(tty, tty_get_baud_rate(tty));
653 /* byte size and parity */
654 switch (cflag & CSIZE) {
669 break; /* too keep GCC shut... */
674 cval |= UART_LCR_PARITY;
675 if (!(cflag & PARODD))
676 cval |= UART_LCR_EPAR;
678 cval |= UART_LCR_SPAR;
680 if ((info->type == PORT_8250) || (info->type == PORT_16450)) {
681 if (info->board->chip_flag) {
682 fcr = UART_FCR_ENABLE_FIFO;
683 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
684 mxser_set_must_fifo_value(info);
688 fcr = UART_FCR_ENABLE_FIFO;
689 if (info->board->chip_flag) {
690 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
691 mxser_set_must_fifo_value(info);
693 switch (info->rx_trigger) {
695 fcr |= UART_FCR_TRIGGER_1;
698 fcr |= UART_FCR_TRIGGER_4;
701 fcr |= UART_FCR_TRIGGER_8;
704 fcr |= UART_FCR_TRIGGER_14;
710 /* CTS flow control flag and modem status interrupts */
711 info->IER &= ~UART_IER_MSI;
712 info->MCR &= ~UART_MCR_AFE;
713 if (cflag & CRTSCTS) {
714 info->port.flags |= ASYNC_CTS_FLOW;
715 info->IER |= UART_IER_MSI;
716 if ((info->type == PORT_16550A) || (info->board->chip_flag)) {
717 info->MCR |= UART_MCR_AFE;
719 status = inb(info->ioaddr + UART_MSR);
720 if (tty->hw_stopped) {
721 if (status & UART_MSR_CTS) {
723 if (info->type != PORT_16550A &&
724 !info->board->chip_flag) {
725 outb(info->IER & ~UART_IER_THRI,
728 info->IER |= UART_IER_THRI;
729 outb(info->IER, info->ioaddr +
735 if (!(status & UART_MSR_CTS)) {
737 if ((info->type != PORT_16550A) &&
738 (!info->board->chip_flag)) {
739 info->IER &= ~UART_IER_THRI;
740 outb(info->IER, info->ioaddr +
747 info->port.flags &= ~ASYNC_CTS_FLOW;
749 outb(info->MCR, info->ioaddr + UART_MCR);
750 if (cflag & CLOCAL) {
751 info->port.flags &= ~ASYNC_CHECK_CD;
753 info->port.flags |= ASYNC_CHECK_CD;
754 info->IER |= UART_IER_MSI;
756 outb(info->IER, info->ioaddr + UART_IER);
759 * Set up parity check flag
761 info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
763 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
764 if (I_BRKINT(tty) || I_PARMRK(tty))
765 info->read_status_mask |= UART_LSR_BI;
767 info->ignore_status_mask = 0;
770 info->ignore_status_mask |= UART_LSR_BI;
771 info->read_status_mask |= UART_LSR_BI;
773 * If we're ignore parity and break indicators, ignore
774 * overruns too. (For real raw support).
777 info->ignore_status_mask |=
781 info->read_status_mask |=
787 if (info->board->chip_flag) {
788 mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty));
789 mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty));
791 mxser_enable_must_rx_software_flow_control(
794 mxser_disable_must_rx_software_flow_control(
798 mxser_enable_must_tx_software_flow_control(
801 mxser_disable_must_tx_software_flow_control(
807 outb(fcr, info->ioaddr + UART_FCR); /* set fcr */
808 outb(cval, info->ioaddr + UART_LCR);
813 static void mxser_check_modem_status(struct tty_struct *tty,
814 struct mxser_port *port, int status)
816 /* update input line counters */
817 if (status & UART_MSR_TERI)
819 if (status & UART_MSR_DDSR)
821 if (status & UART_MSR_DDCD)
823 if (status & UART_MSR_DCTS)
825 port->mon_data.modem_status = status;
826 wake_up_interruptible(&port->port.delta_msr_wait);
828 if ((port->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
829 if (status & UART_MSR_DCD)
830 wake_up_interruptible(&port->port.open_wait);
833 if (tty_port_cts_enabled(&port->port)) {
834 if (tty->hw_stopped) {
835 if (status & UART_MSR_CTS) {
838 if ((port->type != PORT_16550A) &&
839 (!port->board->chip_flag)) {
840 outb(port->IER & ~UART_IER_THRI,
841 port->ioaddr + UART_IER);
842 port->IER |= UART_IER_THRI;
843 outb(port->IER, port->ioaddr +
849 if (!(status & UART_MSR_CTS)) {
851 if (port->type != PORT_16550A &&
852 !port->board->chip_flag) {
853 port->IER &= ~UART_IER_THRI;
854 outb(port->IER, port->ioaddr +
862 static int mxser_activate(struct tty_port *port, struct tty_struct *tty)
864 struct mxser_port *info = container_of(port, struct mxser_port, port);
868 page = __get_free_page(GFP_KERNEL);
872 spin_lock_irqsave(&info->slock, flags);
874 if (!info->ioaddr || !info->type) {
875 set_bit(TTY_IO_ERROR, &tty->flags);
877 spin_unlock_irqrestore(&info->slock, flags);
880 info->port.xmit_buf = (unsigned char *) page;
883 * Clear the FIFO buffers and disable them
884 * (they will be reenabled in mxser_change_speed())
886 if (info->board->chip_flag)
887 outb((UART_FCR_CLEAR_RCVR |
888 UART_FCR_CLEAR_XMIT |
889 MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR);
891 outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
892 info->ioaddr + UART_FCR);
895 * At this point there's no way the LSR could still be 0xFF;
896 * if it is, then bail out, because there's likely no UART
899 if (inb(info->ioaddr + UART_LSR) == 0xff) {
900 spin_unlock_irqrestore(&info->slock, flags);
901 if (capable(CAP_SYS_ADMIN)) {
902 set_bit(TTY_IO_ERROR, &tty->flags);
909 * Clear the interrupt registers.
911 (void) inb(info->ioaddr + UART_LSR);
912 (void) inb(info->ioaddr + UART_RX);
913 (void) inb(info->ioaddr + UART_IIR);
914 (void) inb(info->ioaddr + UART_MSR);
917 * Now, initialize the UART
919 outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */
920 info->MCR = UART_MCR_DTR | UART_MCR_RTS;
921 outb(info->MCR, info->ioaddr + UART_MCR);
924 * Finally, enable interrupts
926 info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
928 if (info->board->chip_flag)
929 info->IER |= MOXA_MUST_IER_EGDAI;
930 outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */
933 * And clear the interrupt registers again for luck.
935 (void) inb(info->ioaddr + UART_LSR);
936 (void) inb(info->ioaddr + UART_RX);
937 (void) inb(info->ioaddr + UART_IIR);
938 (void) inb(info->ioaddr + UART_MSR);
940 clear_bit(TTY_IO_ERROR, &tty->flags);
941 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
944 * and set the speed of the serial port
946 mxser_change_speed(tty, NULL);
947 spin_unlock_irqrestore(&info->slock, flags);
953 * This routine will shutdown a serial port
955 static void mxser_shutdown_port(struct tty_port *port)
957 struct mxser_port *info = container_of(port, struct mxser_port, port);
960 spin_lock_irqsave(&info->slock, flags);
963 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
964 * here so the queue might never be waken up
966 wake_up_interruptible(&info->port.delta_msr_wait);
969 * Free the xmit buffer, if necessary
971 if (info->port.xmit_buf) {
972 free_page((unsigned long) info->port.xmit_buf);
973 info->port.xmit_buf = NULL;
977 outb(0x00, info->ioaddr + UART_IER);
979 /* clear Rx/Tx FIFO's */
980 if (info->board->chip_flag)
981 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT |
982 MOXA_MUST_FCR_GDA_MODE_ENABLE,
983 info->ioaddr + UART_FCR);
985 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
986 info->ioaddr + UART_FCR);
988 /* read data port to reset things */
989 (void) inb(info->ioaddr + UART_RX);
992 if (info->board->chip_flag)
993 SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr);
995 spin_unlock_irqrestore(&info->slock, flags);
999 * This routine is called whenever a serial port is opened. It
1000 * enables interrupts for a serial port, linking in its async structure into
1001 * the IRQ chain. It also performs the serial-specific
1002 * initialization for the tty structure.
1004 static int mxser_open(struct tty_struct *tty, struct file *filp)
1006 struct mxser_port *info;
1010 if (line == MXSER_PORTS)
1012 info = &mxser_boards[line / MXSER_PORTS_PER_BOARD].ports[line % MXSER_PORTS_PER_BOARD];
1016 tty->driver_data = info;
1017 return tty_port_open(&info->port, tty, filp);
1020 static void mxser_flush_buffer(struct tty_struct *tty)
1022 struct mxser_port *info = tty->driver_data;
1024 unsigned long flags;
1027 spin_lock_irqsave(&info->slock, flags);
1028 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1030 fcr = inb(info->ioaddr + UART_FCR);
1031 outb((fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
1032 info->ioaddr + UART_FCR);
1033 outb(fcr, info->ioaddr + UART_FCR);
1035 spin_unlock_irqrestore(&info->slock, flags);
1041 static void mxser_close_port(struct tty_port *port)
1043 struct mxser_port *info = container_of(port, struct mxser_port, port);
1044 unsigned long timeout;
1046 * At this point we stop accepting input. To do this, we
1047 * disable the receive line status interrupts, and tell the
1048 * interrupt driver to stop checking the data ready bit in the
1049 * line status register.
1051 info->IER &= ~UART_IER_RLSI;
1052 if (info->board->chip_flag)
1053 info->IER &= ~MOXA_MUST_RECV_ISR;
1055 outb(info->IER, info->ioaddr + UART_IER);
1057 * Before we drop DTR, make sure the UART transmitter
1058 * has completely drained; this is especially
1059 * important if there is a transmit FIFO!
1061 timeout = jiffies + HZ;
1062 while (!(inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT)) {
1063 schedule_timeout_interruptible(5);
1064 if (time_after(jiffies, timeout))
1070 * This routine is called when the serial port gets closed. First, we
1071 * wait for the last remaining data to be sent. Then, we unlink its
1072 * async structure from the interrupt chain if necessary, and we free
1073 * that IRQ if nothing is left in the chain.
1075 static void mxser_close(struct tty_struct *tty, struct file *filp)
1077 struct mxser_port *info = tty->driver_data;
1078 struct tty_port *port = &info->port;
1080 if (tty->index == MXSER_PORTS || info == NULL)
1082 if (tty_port_close_start(port, tty, filp) == 0)
1084 mutex_lock(&port->mutex);
1085 mxser_close_port(port);
1086 mxser_flush_buffer(tty);
1087 if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
1089 tty_port_lower_dtr_rts(port);
1091 mxser_shutdown_port(port);
1092 clear_bit(ASYNCB_INITIALIZED, &port->flags);
1093 mutex_unlock(&port->mutex);
1094 /* Right now the tty_port set is done outside of the close_end helper
1095 as we don't yet have everyone using refcounts */
1096 tty_port_close_end(port, tty);
1097 tty_port_tty_set(port, NULL);
1100 static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count)
1103 struct mxser_port *info = tty->driver_data;
1104 unsigned long flags;
1106 if (!info->port.xmit_buf)
1110 c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
1111 SERIAL_XMIT_SIZE - info->xmit_head));
1115 memcpy(info->port.xmit_buf + info->xmit_head, buf, c);
1116 spin_lock_irqsave(&info->slock, flags);
1117 info->xmit_head = (info->xmit_head + c) &
1118 (SERIAL_XMIT_SIZE - 1);
1119 info->xmit_cnt += c;
1120 spin_unlock_irqrestore(&info->slock, flags);
1127 if (info->xmit_cnt && !tty->stopped) {
1128 if (!tty->hw_stopped ||
1129 (info->type == PORT_16550A) ||
1130 (info->board->chip_flag)) {
1131 spin_lock_irqsave(&info->slock, flags);
1132 outb(info->IER & ~UART_IER_THRI, info->ioaddr +
1134 info->IER |= UART_IER_THRI;
1135 outb(info->IER, info->ioaddr + UART_IER);
1136 spin_unlock_irqrestore(&info->slock, flags);
1142 static int mxser_put_char(struct tty_struct *tty, unsigned char ch)
1144 struct mxser_port *info = tty->driver_data;
1145 unsigned long flags;
1147 if (!info->port.xmit_buf)
1150 if (info->xmit_cnt >= SERIAL_XMIT_SIZE - 1)
1153 spin_lock_irqsave(&info->slock, flags);
1154 info->port.xmit_buf[info->xmit_head++] = ch;
1155 info->xmit_head &= SERIAL_XMIT_SIZE - 1;
1157 spin_unlock_irqrestore(&info->slock, flags);
1158 if (!tty->stopped) {
1159 if (!tty->hw_stopped ||
1160 (info->type == PORT_16550A) ||
1161 info->board->chip_flag) {
1162 spin_lock_irqsave(&info->slock, flags);
1163 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1164 info->IER |= UART_IER_THRI;
1165 outb(info->IER, info->ioaddr + UART_IER);
1166 spin_unlock_irqrestore(&info->slock, flags);
1173 static void mxser_flush_chars(struct tty_struct *tty)
1175 struct mxser_port *info = tty->driver_data;
1176 unsigned long flags;
1178 if (info->xmit_cnt <= 0 || tty->stopped || !info->port.xmit_buf ||
1179 (tty->hw_stopped && info->type != PORT_16550A &&
1180 !info->board->chip_flag))
1183 spin_lock_irqsave(&info->slock, flags);
1185 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1186 info->IER |= UART_IER_THRI;
1187 outb(info->IER, info->ioaddr + UART_IER);
1189 spin_unlock_irqrestore(&info->slock, flags);
1192 static int mxser_write_room(struct tty_struct *tty)
1194 struct mxser_port *info = tty->driver_data;
1197 ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
1198 return ret < 0 ? 0 : ret;
1201 static int mxser_chars_in_buffer(struct tty_struct *tty)
1203 struct mxser_port *info = tty->driver_data;
1204 return info->xmit_cnt;
1208 * ------------------------------------------------------------
1209 * friends of mxser_ioctl()
1210 * ------------------------------------------------------------
1212 static int mxser_get_serial_info(struct tty_struct *tty,
1213 struct serial_struct __user *retinfo)
1215 struct mxser_port *info = tty->driver_data;
1216 struct serial_struct tmp = {
1219 .port = info->ioaddr,
1220 .irq = info->board->irq,
1221 .flags = info->port.flags,
1222 .baud_base = info->baud_base,
1223 .close_delay = info->port.close_delay,
1224 .closing_wait = info->port.closing_wait,
1225 .custom_divisor = info->custom_divisor,
1228 if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
1233 static int mxser_set_serial_info(struct tty_struct *tty,
1234 struct serial_struct __user *new_info)
1236 struct mxser_port *info = tty->driver_data;
1237 struct tty_port *port = &info->port;
1238 struct serial_struct new_serial;
1240 unsigned long sl_flags;
1244 if (!new_info || !info->ioaddr)
1246 if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
1249 if (new_serial.irq != info->board->irq ||
1250 new_serial.port != info->ioaddr)
1253 flags = port->flags & ASYNC_SPD_MASK;
1255 if (!capable(CAP_SYS_ADMIN)) {
1256 if ((new_serial.baud_base != info->baud_base) ||
1257 (new_serial.close_delay != info->port.close_delay) ||
1258 ((new_serial.flags & ~ASYNC_USR_MASK) != (info->port.flags & ~ASYNC_USR_MASK)))
1260 info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) |
1261 (new_serial.flags & ASYNC_USR_MASK));
1264 * OK, past this point, all the error checking has been done.
1265 * At this point, we start making changes.....
1267 port->flags = ((port->flags & ~ASYNC_FLAGS) |
1268 (new_serial.flags & ASYNC_FLAGS));
1269 port->close_delay = new_serial.close_delay * HZ / 100;
1270 port->closing_wait = new_serial.closing_wait * HZ / 100;
1271 port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
1272 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST &&
1273 (new_serial.baud_base != info->baud_base ||
1274 new_serial.custom_divisor !=
1275 info->custom_divisor)) {
1276 if (new_serial.custom_divisor == 0)
1278 baud = new_serial.baud_base / new_serial.custom_divisor;
1279 tty_encode_baud_rate(tty, baud, baud);
1283 info->type = new_serial.type;
1285 process_txrx_fifo(info);
1287 if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
1288 if (flags != (port->flags & ASYNC_SPD_MASK)) {
1289 spin_lock_irqsave(&info->slock, sl_flags);
1290 mxser_change_speed(tty, NULL);
1291 spin_unlock_irqrestore(&info->slock, sl_flags);
1294 retval = mxser_activate(port, tty);
1296 set_bit(ASYNCB_INITIALIZED, &port->flags);
1302 * mxser_get_lsr_info - get line status register info
1304 * Purpose: Let user call ioctl() to get info when the UART physically
1305 * is emptied. On bus types like RS485, the transmitter must
1306 * release the bus after transmitting. This must be done when
1307 * the transmit shift register is empty, not be done when the
1308 * transmit holding register is empty. This functionality
1309 * allows an RS485 driver to be written in user space.
1311 static int mxser_get_lsr_info(struct mxser_port *info,
1312 unsigned int __user *value)
1314 unsigned char status;
1315 unsigned int result;
1316 unsigned long flags;
1318 spin_lock_irqsave(&info->slock, flags);
1319 status = inb(info->ioaddr + UART_LSR);
1320 spin_unlock_irqrestore(&info->slock, flags);
1321 result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
1322 return put_user(result, value);
1325 static int mxser_tiocmget(struct tty_struct *tty)
1327 struct mxser_port *info = tty->driver_data;
1328 unsigned char control, status;
1329 unsigned long flags;
1332 if (tty->index == MXSER_PORTS)
1333 return -ENOIOCTLCMD;
1334 if (test_bit(TTY_IO_ERROR, &tty->flags))
1337 control = info->MCR;
1339 spin_lock_irqsave(&info->slock, flags);
1340 status = inb(info->ioaddr + UART_MSR);
1341 if (status & UART_MSR_ANY_DELTA)
1342 mxser_check_modem_status(tty, info, status);
1343 spin_unlock_irqrestore(&info->slock, flags);
1344 return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
1345 ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
1346 ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) |
1347 ((status & UART_MSR_RI) ? TIOCM_RNG : 0) |
1348 ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) |
1349 ((status & UART_MSR_CTS) ? TIOCM_CTS : 0);
1352 static int mxser_tiocmset(struct tty_struct *tty,
1353 unsigned int set, unsigned int clear)
1355 struct mxser_port *info = tty->driver_data;
1356 unsigned long flags;
1359 if (tty->index == MXSER_PORTS)
1360 return -ENOIOCTLCMD;
1361 if (test_bit(TTY_IO_ERROR, &tty->flags))
1364 spin_lock_irqsave(&info->slock, flags);
1366 if (set & TIOCM_RTS)
1367 info->MCR |= UART_MCR_RTS;
1368 if (set & TIOCM_DTR)
1369 info->MCR |= UART_MCR_DTR;
1371 if (clear & TIOCM_RTS)
1372 info->MCR &= ~UART_MCR_RTS;
1373 if (clear & TIOCM_DTR)
1374 info->MCR &= ~UART_MCR_DTR;
1376 outb(info->MCR, info->ioaddr + UART_MCR);
1377 spin_unlock_irqrestore(&info->slock, flags);
1381 static int __init mxser_program_mode(int port)
1393 id = inb(port + 1) & 0x1F;
1394 if ((id != C168_ASIC_ID) &&
1395 (id != C104_ASIC_ID) &&
1396 (id != C102_ASIC_ID) &&
1397 (id != CI132_ASIC_ID) &&
1398 (id != CI134_ASIC_ID) &&
1399 (id != CI104J_ASIC_ID))
1401 for (i = 0, j = 0; i < 4; i++) {
1405 } else if ((j == 1) && (n == 1)) {
1416 static void __init mxser_normal_mode(int port)
1420 outb(0xA5, port + 1);
1421 outb(0x80, port + 3);
1422 outb(12, port + 0); /* 9600 bps */
1424 outb(0x03, port + 3); /* 8 data bits */
1425 outb(0x13, port + 4); /* loop back mode */
1426 for (i = 0; i < 16; i++) {
1428 if ((n & 0x61) == 0x60)
1433 outb(0x00, port + 4);
1436 #define CHIP_SK 0x01 /* Serial Data Clock in Eprom */
1437 #define CHIP_DO 0x02 /* Serial Data Output in Eprom */
1438 #define CHIP_CS 0x04 /* Serial Chip Select in Eprom */
1439 #define CHIP_DI 0x08 /* Serial Data Input in Eprom */
1440 #define EN_CCMD 0x000 /* Chip's command register */
1441 #define EN0_RSARLO 0x008 /* Remote start address reg 0 */
1442 #define EN0_RSARHI 0x009 /* Remote start address reg 1 */
1443 #define EN0_RCNTLO 0x00A /* Remote byte count reg WR */
1444 #define EN0_RCNTHI 0x00B /* Remote byte count reg WR */
1445 #define EN0_DCFG 0x00E /* Data configuration reg WR */
1446 #define EN0_PORT 0x010 /* Rcv missed frame error counter RD */
1447 #define ENC_PAGE0 0x000 /* Select page 0 of chip registers */
1448 #define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */
1449 static int __init mxser_read_register(int port, unsigned short *regs)
1451 int i, k, value, id;
1454 id = mxser_program_mode(port);
1457 for (i = 0; i < 14; i++) {
1458 k = (i & 0x3F) | 0x180;
1459 for (j = 0x100; j > 0; j >>= 1) {
1460 outb(CHIP_CS, port);
1462 outb(CHIP_CS | CHIP_DO, port);
1463 outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */
1465 outb(CHIP_CS, port);
1466 outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */
1471 for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) {
1472 outb(CHIP_CS, port);
1473 outb(CHIP_CS | CHIP_SK, port);
1474 if (inb(port) & CHIP_DI)
1480 mxser_normal_mode(port);
1484 static int mxser_ioctl_special(unsigned int cmd, void __user *argp)
1486 struct mxser_port *ip;
1487 struct tty_port *port;
1488 struct tty_struct *tty;
1494 case MOXA_GET_MAJOR:
1495 printk_ratelimited(KERN_WARNING "mxser: '%s' uses deprecated ioctl "
1496 "%x (GET_MAJOR), fix your userspace\n",
1497 current->comm, cmd);
1498 return put_user(ttymajor, (int __user *)argp);
1500 case MOXA_CHKPORTENABLE:
1502 for (i = 0; i < MXSER_BOARDS; i++)
1503 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++)
1504 if (mxser_boards[i].ports[j].ioaddr)
1506 return put_user(result, (unsigned long __user *)argp);
1507 case MOXA_GETDATACOUNT:
1508 /* The receive side is locked by port->slock but it isn't
1509 clear that an exact snapshot is worth copying here */
1510 if (copy_to_user(argp, &mxvar_log, sizeof(mxvar_log)))
1513 case MOXA_GETMSTATUS: {
1514 struct mxser_mstatus ms, __user *msu = argp;
1515 for (i = 0; i < MXSER_BOARDS; i++)
1516 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) {
1517 ip = &mxser_boards[i].ports[j];
1519 memset(&ms, 0, sizeof(ms));
1521 mutex_lock(&port->mutex);
1525 tty = tty_port_tty_get(port);
1528 ms.cflag = ip->normal_termios.c_cflag;
1530 ms.cflag = tty->termios.c_cflag;
1532 spin_lock_irq(&ip->slock);
1533 status = inb(ip->ioaddr + UART_MSR);
1534 spin_unlock_irq(&ip->slock);
1535 if (status & UART_MSR_DCD)
1537 if (status & UART_MSR_DSR)
1539 if (status & UART_MSR_CTS)
1542 mutex_unlock(&port->mutex);
1543 if (copy_to_user(msu, &ms, sizeof(ms)))
1549 case MOXA_ASPP_MON_EXT: {
1550 struct mxser_mon_ext *me; /* it's 2k, stack unfriendly */
1551 unsigned int cflag, iflag, p;
1554 me = kzalloc(sizeof(*me), GFP_KERNEL);
1558 for (i = 0, p = 0; i < MXSER_BOARDS; i++) {
1559 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++, p++) {
1560 if (p >= ARRAY_SIZE(me->rx_cnt)) {
1564 ip = &mxser_boards[i].ports[j];
1567 mutex_lock(&port->mutex);
1569 mutex_unlock(&port->mutex);
1573 spin_lock_irq(&ip->slock);
1574 status = mxser_get_msr(ip->ioaddr, 0, p);
1576 if (status & UART_MSR_TERI)
1578 if (status & UART_MSR_DDSR)
1580 if (status & UART_MSR_DDCD)
1582 if (status & UART_MSR_DCTS)
1585 ip->mon_data.modem_status = status;
1586 me->rx_cnt[p] = ip->mon_data.rxcnt;
1587 me->tx_cnt[p] = ip->mon_data.txcnt;
1588 me->up_rxcnt[p] = ip->mon_data.up_rxcnt;
1589 me->up_txcnt[p] = ip->mon_data.up_txcnt;
1590 me->modem_status[p] =
1591 ip->mon_data.modem_status;
1592 spin_unlock_irq(&ip->slock);
1594 tty = tty_port_tty_get(&ip->port);
1597 cflag = ip->normal_termios.c_cflag;
1598 iflag = ip->normal_termios.c_iflag;
1599 me->baudrate[p] = tty_termios_baud_rate(&ip->normal_termios);
1601 cflag = tty->termios.c_cflag;
1602 iflag = tty->termios.c_iflag;
1603 me->baudrate[p] = tty_get_baud_rate(tty);
1607 me->databits[p] = cflag & CSIZE;
1608 me->stopbits[p] = cflag & CSTOPB;
1609 me->parity[p] = cflag & (PARENB | PARODD |
1612 if (cflag & CRTSCTS)
1613 me->flowctrl[p] |= 0x03;
1615 if (iflag & (IXON | IXOFF))
1616 me->flowctrl[p] |= 0x0C;
1618 if (ip->type == PORT_16550A)
1621 if (ip->board->chip_flag == MOXA_MUST_MU860_HWID) {
1622 opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2);
1623 opmode &= OP_MODE_MASK;
1625 opmode = RS232_MODE;
1627 me->iftype[p] = opmode;
1628 mutex_unlock(&port->mutex);
1631 if (copy_to_user(argp, me, sizeof(*me)))
1637 return -ENOIOCTLCMD;
1642 static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg,
1643 struct async_icount *cprev)
1645 struct async_icount cnow;
1646 unsigned long flags;
1649 spin_lock_irqsave(&info->slock, flags);
1650 cnow = info->icount; /* atomic copy */
1651 spin_unlock_irqrestore(&info->slock, flags);
1653 ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
1654 ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
1655 ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) ||
1656 ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
1663 static int mxser_ioctl(struct tty_struct *tty,
1664 unsigned int cmd, unsigned long arg)
1666 struct mxser_port *info = tty->driver_data;
1667 struct tty_port *port = &info->port;
1668 struct async_icount cnow;
1669 unsigned long flags;
1670 void __user *argp = (void __user *)arg;
1673 if (tty->index == MXSER_PORTS)
1674 return mxser_ioctl_special(cmd, argp);
1676 if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) {
1678 unsigned long opmode;
1679 static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f };
1681 unsigned char val, mask;
1683 if (info->board->chip_flag != MOXA_MUST_MU860_HWID)
1687 if (cmd == MOXA_SET_OP_MODE) {
1688 if (get_user(opmode, (int __user *) argp))
1690 if (opmode != RS232_MODE &&
1691 opmode != RS485_2WIRE_MODE &&
1692 opmode != RS422_MODE &&
1693 opmode != RS485_4WIRE_MODE)
1697 spin_lock_irq(&info->slock);
1698 val = inb(info->opmode_ioaddr);
1700 val |= (opmode << shiftbit);
1701 outb(val, info->opmode_ioaddr);
1702 spin_unlock_irq(&info->slock);
1705 spin_lock_irq(&info->slock);
1706 opmode = inb(info->opmode_ioaddr) >> shiftbit;
1707 spin_unlock_irq(&info->slock);
1708 opmode &= OP_MODE_MASK;
1709 if (put_user(opmode, (int __user *)argp))
1715 if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT &&
1716 test_bit(TTY_IO_ERROR, &tty->flags))
1721 mutex_lock(&port->mutex);
1722 retval = mxser_get_serial_info(tty, argp);
1723 mutex_unlock(&port->mutex);
1726 mutex_lock(&port->mutex);
1727 retval = mxser_set_serial_info(tty, argp);
1728 mutex_unlock(&port->mutex);
1730 case TIOCSERGETLSR: /* Get line status register */
1731 return mxser_get_lsr_info(info, argp);
1733 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
1734 * - mask passed in arg for lines of interest
1735 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
1736 * Caller should use TIOCGICOUNT to see which one it was
1739 spin_lock_irqsave(&info->slock, flags);
1740 cnow = info->icount; /* note the counters on entry */
1741 spin_unlock_irqrestore(&info->slock, flags);
1743 return wait_event_interruptible(info->port.delta_msr_wait,
1744 mxser_cflags_changed(info, arg, &cnow));
1745 case MOXA_HighSpeedOn:
1746 return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp);
1747 case MOXA_SDS_RSTICOUNTER:
1748 spin_lock_irq(&info->slock);
1749 info->mon_data.rxcnt = 0;
1750 info->mon_data.txcnt = 0;
1751 spin_unlock_irq(&info->slock);
1754 case MOXA_ASPP_OQUEUE:{
1757 len = mxser_chars_in_buffer(tty);
1758 spin_lock_irq(&info->slock);
1759 lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_THRE;
1760 spin_unlock_irq(&info->slock);
1761 len += (lsr ? 0 : 1);
1763 return put_user(len, (int __user *)argp);
1765 case MOXA_ASPP_MON: {
1768 spin_lock_irq(&info->slock);
1769 status = mxser_get_msr(info->ioaddr, 1, tty->index);
1770 mxser_check_modem_status(tty, info, status);
1772 mcr = inb(info->ioaddr + UART_MCR);
1773 spin_unlock_irq(&info->slock);
1775 if (mcr & MOXA_MUST_MCR_XON_FLAG)
1776 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD;
1778 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD;
1780 if (mcr & MOXA_MUST_MCR_TX_XON)
1781 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT;
1783 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT;
1785 if (tty->hw_stopped)
1786 info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD;
1788 info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD;
1790 if (copy_to_user(argp, &info->mon_data,
1791 sizeof(struct mxser_mon)))
1796 case MOXA_ASPP_LSTATUS: {
1797 if (put_user(info->err_shadow, (unsigned char __user *)argp))
1800 info->err_shadow = 0;
1803 case MOXA_SET_BAUD_METHOD: {
1806 if (get_user(method, (int __user *)argp))
1808 mxser_set_baud_method[tty->index] = method;
1809 return put_user(method, (int __user *)argp);
1812 return -ENOIOCTLCMD;
1818 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
1819 * Return: write counters to the user passed counter struct
1820 * NB: both 1->0 and 0->1 transitions are counted except for
1821 * RI where only 0->1 is counted.
1824 static int mxser_get_icount(struct tty_struct *tty,
1825 struct serial_icounter_struct *icount)
1828 struct mxser_port *info = tty->driver_data;
1829 struct async_icount cnow;
1830 unsigned long flags;
1832 spin_lock_irqsave(&info->slock, flags);
1833 cnow = info->icount;
1834 spin_unlock_irqrestore(&info->slock, flags);
1836 icount->frame = cnow.frame;
1837 icount->brk = cnow.brk;
1838 icount->overrun = cnow.overrun;
1839 icount->buf_overrun = cnow.buf_overrun;
1840 icount->parity = cnow.parity;
1841 icount->rx = cnow.rx;
1842 icount->tx = cnow.tx;
1843 icount->cts = cnow.cts;
1844 icount->dsr = cnow.dsr;
1845 icount->rng = cnow.rng;
1846 icount->dcd = cnow.dcd;
1850 static void mxser_stoprx(struct tty_struct *tty)
1852 struct mxser_port *info = tty->driver_data;
1854 info->ldisc_stop_rx = 1;
1856 if (info->board->chip_flag) {
1857 info->IER &= ~MOXA_MUST_RECV_ISR;
1858 outb(info->IER, info->ioaddr + UART_IER);
1860 info->x_char = STOP_CHAR(tty);
1861 outb(0, info->ioaddr + UART_IER);
1862 info->IER |= UART_IER_THRI;
1863 outb(info->IER, info->ioaddr + UART_IER);
1867 if (tty->termios.c_cflag & CRTSCTS) {
1868 info->MCR &= ~UART_MCR_RTS;
1869 outb(info->MCR, info->ioaddr + UART_MCR);
1874 * This routine is called by the upper-layer tty layer to signal that
1875 * incoming characters should be throttled.
1877 static void mxser_throttle(struct tty_struct *tty)
1882 static void mxser_unthrottle(struct tty_struct *tty)
1884 struct mxser_port *info = tty->driver_data;
1887 info->ldisc_stop_rx = 0;
1892 if (info->board->chip_flag) {
1893 info->IER |= MOXA_MUST_RECV_ISR;
1894 outb(info->IER, info->ioaddr + UART_IER);
1896 info->x_char = START_CHAR(tty);
1897 outb(0, info->ioaddr + UART_IER);
1898 info->IER |= UART_IER_THRI;
1899 outb(info->IER, info->ioaddr + UART_IER);
1904 if (tty->termios.c_cflag & CRTSCTS) {
1905 info->MCR |= UART_MCR_RTS;
1906 outb(info->MCR, info->ioaddr + UART_MCR);
1911 * mxser_stop() and mxser_start()
1913 * This routines are called before setting or resetting tty->stopped.
1914 * They enable or disable transmitter interrupts, as necessary.
1916 static void mxser_stop(struct tty_struct *tty)
1918 struct mxser_port *info = tty->driver_data;
1919 unsigned long flags;
1921 spin_lock_irqsave(&info->slock, flags);
1922 if (info->IER & UART_IER_THRI) {
1923 info->IER &= ~UART_IER_THRI;
1924 outb(info->IER, info->ioaddr + UART_IER);
1926 spin_unlock_irqrestore(&info->slock, flags);
1929 static void mxser_start(struct tty_struct *tty)
1931 struct mxser_port *info = tty->driver_data;
1932 unsigned long flags;
1934 spin_lock_irqsave(&info->slock, flags);
1935 if (info->xmit_cnt && info->port.xmit_buf) {
1936 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1937 info->IER |= UART_IER_THRI;
1938 outb(info->IER, info->ioaddr + UART_IER);
1940 spin_unlock_irqrestore(&info->slock, flags);
1943 static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
1945 struct mxser_port *info = tty->driver_data;
1946 unsigned long flags;
1948 spin_lock_irqsave(&info->slock, flags);
1949 mxser_change_speed(tty, old_termios);
1950 spin_unlock_irqrestore(&info->slock, flags);
1952 if ((old_termios->c_cflag & CRTSCTS) &&
1953 !(tty->termios.c_cflag & CRTSCTS)) {
1954 tty->hw_stopped = 0;
1958 /* Handle sw stopped */
1959 if ((old_termios->c_iflag & IXON) &&
1960 !(tty->termios.c_iflag & IXON)) {
1963 if (info->board->chip_flag) {
1964 spin_lock_irqsave(&info->slock, flags);
1965 mxser_disable_must_rx_software_flow_control(
1967 spin_unlock_irqrestore(&info->slock, flags);
1975 * mxser_wait_until_sent() --- wait until the transmitter is empty
1977 static void mxser_wait_until_sent(struct tty_struct *tty, int timeout)
1979 struct mxser_port *info = tty->driver_data;
1980 unsigned long orig_jiffies, char_time;
1981 unsigned long flags;
1984 if (info->type == PORT_UNKNOWN)
1987 if (info->xmit_fifo_size == 0)
1988 return; /* Just in case.... */
1990 orig_jiffies = jiffies;
1992 * Set the check interval to be 1/5 of the estimated time to
1993 * send a single character, and make it at least 1. The check
1994 * interval should also be less than the timeout.
1996 * Note: we have to use pretty tight timings here to satisfy
1999 char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size;
2000 char_time = char_time / 5;
2003 if (timeout && timeout < char_time)
2004 char_time = timeout;
2006 * If the transmitter hasn't cleared in twice the approximate
2007 * amount of time to send the entire FIFO, it probably won't
2008 * ever clear. This assumes the UART isn't doing flow
2009 * control, which is currently the case. Hence, if it ever
2010 * takes longer than info->timeout, this is probably due to a
2011 * UART bug of some kind. So, we clamp the timeout parameter at
2014 if (!timeout || timeout > 2 * info->timeout)
2015 timeout = 2 * info->timeout;
2017 spin_lock_irqsave(&info->slock, flags);
2018 while (!((lsr = inb(info->ioaddr + UART_LSR)) & UART_LSR_TEMT)) {
2019 spin_unlock_irqrestore(&info->slock, flags);
2020 schedule_timeout_interruptible(char_time);
2021 spin_lock_irqsave(&info->slock, flags);
2022 if (signal_pending(current))
2024 if (timeout && time_after(jiffies, orig_jiffies + timeout))
2027 spin_unlock_irqrestore(&info->slock, flags);
2028 set_current_state(TASK_RUNNING);
2032 * This routine is called by tty_hangup() when a hangup is signaled.
2034 static void mxser_hangup(struct tty_struct *tty)
2036 struct mxser_port *info = tty->driver_data;
2038 mxser_flush_buffer(tty);
2039 tty_port_hangup(&info->port);
2043 * mxser_rs_break() --- routine which turns the break handling on or off
2045 static int mxser_rs_break(struct tty_struct *tty, int break_state)
2047 struct mxser_port *info = tty->driver_data;
2048 unsigned long flags;
2050 spin_lock_irqsave(&info->slock, flags);
2051 if (break_state == -1)
2052 outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC,
2053 info->ioaddr + UART_LCR);
2055 outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC,
2056 info->ioaddr + UART_LCR);
2057 spin_unlock_irqrestore(&info->slock, flags);
2061 static void mxser_receive_chars(struct tty_struct *tty,
2062 struct mxser_port *port, int *status)
2064 unsigned char ch, gdl;
2070 recv_room = tty->receive_room;
2071 if (recv_room == 0 && !port->ldisc_stop_rx)
2073 if (port->board->chip_flag != MOXA_OTHER_UART) {
2075 if (*status & UART_LSR_SPECIAL)
2077 if (port->board->chip_flag == MOXA_MUST_MU860_HWID &&
2078 (*status & MOXA_MUST_LSR_RERR))
2080 if (*status & MOXA_MUST_LSR_RERR)
2083 gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER);
2085 if (port->board->chip_flag == MOXA_MUST_MU150_HWID)
2086 gdl &= MOXA_MUST_GDL_MASK;
2087 if (gdl >= recv_room) {
2088 if (!port->ldisc_stop_rx)
2092 ch = inb(port->ioaddr + UART_RX);
2093 tty_insert_flip_char(&port->port, ch, 0);
2104 ch = inb(port->ioaddr + UART_RX);
2105 if (port->board->chip_flag && (*status & UART_LSR_OE))
2106 outb(0x23, port->ioaddr + UART_FCR);
2107 *status &= port->read_status_mask;
2108 if (*status & port->ignore_status_mask) {
2109 if (++ignored > 100)
2113 if (*status & UART_LSR_SPECIAL) {
2114 if (*status & UART_LSR_BI) {
2118 if (port->port.flags & ASYNC_SAK)
2120 } else if (*status & UART_LSR_PE) {
2122 port->icount.parity++;
2123 } else if (*status & UART_LSR_FE) {
2125 port->icount.frame++;
2126 } else if (*status & UART_LSR_OE) {
2128 port->icount.overrun++;
2132 tty_insert_flip_char(&port->port, ch, flag);
2134 if (cnt >= recv_room) {
2135 if (!port->ldisc_stop_rx)
2142 if (port->board->chip_flag)
2145 *status = inb(port->ioaddr + UART_LSR);
2146 } while (*status & UART_LSR_DR);
2149 mxvar_log.rxcnt[tty->index] += cnt;
2150 port->mon_data.rxcnt += cnt;
2151 port->mon_data.up_rxcnt += cnt;
2154 * We are called from an interrupt context with &port->slock
2155 * being held. Drop it temporarily in order to prevent
2156 * recursive locking.
2158 spin_unlock(&port->slock);
2159 tty_flip_buffer_push(&port->port);
2160 spin_lock(&port->slock);
2163 static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port)
2168 outb(port->x_char, port->ioaddr + UART_TX);
2170 mxvar_log.txcnt[tty->index]++;
2171 port->mon_data.txcnt++;
2172 port->mon_data.up_txcnt++;
2177 if (port->port.xmit_buf == NULL)
2180 if (port->xmit_cnt <= 0 || tty->stopped ||
2182 (port->type != PORT_16550A) &&
2183 (!port->board->chip_flag))) {
2184 port->IER &= ~UART_IER_THRI;
2185 outb(port->IER, port->ioaddr + UART_IER);
2189 cnt = port->xmit_cnt;
2190 count = port->xmit_fifo_size;
2192 outb(port->port.xmit_buf[port->xmit_tail++],
2193 port->ioaddr + UART_TX);
2194 port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE - 1);
2195 if (--port->xmit_cnt <= 0)
2197 } while (--count > 0);
2198 mxvar_log.txcnt[tty->index] += (cnt - port->xmit_cnt);
2200 port->mon_data.txcnt += (cnt - port->xmit_cnt);
2201 port->mon_data.up_txcnt += (cnt - port->xmit_cnt);
2202 port->icount.tx += (cnt - port->xmit_cnt);
2204 if (port->xmit_cnt < WAKEUP_CHARS)
2207 if (port->xmit_cnt <= 0) {
2208 port->IER &= ~UART_IER_THRI;
2209 outb(port->IER, port->ioaddr + UART_IER);
2214 * This is the serial driver's generic interrupt routine
2216 static irqreturn_t mxser_interrupt(int irq, void *dev_id)
2219 struct mxser_board *brd = NULL;
2220 struct mxser_port *port;
2221 int max, irqbits, bits, msr;
2222 unsigned int int_cnt, pass_counter = 0;
2223 int handled = IRQ_NONE;
2224 struct tty_struct *tty;
2226 for (i = 0; i < MXSER_BOARDS; i++)
2227 if (dev_id == &mxser_boards[i]) {
2232 if (i == MXSER_BOARDS)
2236 max = brd->info->nports;
2237 while (pass_counter++ < MXSER_ISR_PASS_LIMIT) {
2238 irqbits = inb(brd->vector) & brd->vector_mask;
2239 if (irqbits == brd->vector_mask)
2242 handled = IRQ_HANDLED;
2243 for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) {
2244 if (irqbits == brd->vector_mask)
2248 port = &brd->ports[i];
2251 spin_lock(&port->slock);
2253 iir = inb(port->ioaddr + UART_IIR);
2254 if (iir & UART_IIR_NO_INT)
2256 iir &= MOXA_MUST_IIR_MASK;
2257 tty = tty_port_tty_get(&port->port);
2259 (port->port.flags & ASYNC_CLOSING) ||
2260 !(port->port.flags &
2261 ASYNC_INITIALIZED)) {
2262 status = inb(port->ioaddr + UART_LSR);
2263 outb(0x27, port->ioaddr + UART_FCR);
2264 inb(port->ioaddr + UART_MSR);
2269 status = inb(port->ioaddr + UART_LSR);
2271 if (status & UART_LSR_PE)
2272 port->err_shadow |= NPPI_NOTIFY_PARITY;
2273 if (status & UART_LSR_FE)
2274 port->err_shadow |= NPPI_NOTIFY_FRAMING;
2275 if (status & UART_LSR_OE)
2277 NPPI_NOTIFY_HW_OVERRUN;
2278 if (status & UART_LSR_BI)
2279 port->err_shadow |= NPPI_NOTIFY_BREAK;
2281 if (port->board->chip_flag) {
2282 if (iir == MOXA_MUST_IIR_GDA ||
2283 iir == MOXA_MUST_IIR_RDA ||
2284 iir == MOXA_MUST_IIR_RTO ||
2285 iir == MOXA_MUST_IIR_LSR)
2286 mxser_receive_chars(tty, port,
2290 status &= port->read_status_mask;
2291 if (status & UART_LSR_DR)
2292 mxser_receive_chars(tty, port,
2295 msr = inb(port->ioaddr + UART_MSR);
2296 if (msr & UART_MSR_ANY_DELTA)
2297 mxser_check_modem_status(tty, port, msr);
2299 if (port->board->chip_flag) {
2300 if (iir == 0x02 && (status &
2302 mxser_transmit_chars(tty, port);
2304 if (status & UART_LSR_THRE)
2305 mxser_transmit_chars(tty, port);
2308 } while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
2309 spin_unlock(&port->slock);
2317 static const struct tty_operations mxser_ops = {
2319 .close = mxser_close,
2320 .write = mxser_write,
2321 .put_char = mxser_put_char,
2322 .flush_chars = mxser_flush_chars,
2323 .write_room = mxser_write_room,
2324 .chars_in_buffer = mxser_chars_in_buffer,
2325 .flush_buffer = mxser_flush_buffer,
2326 .ioctl = mxser_ioctl,
2327 .throttle = mxser_throttle,
2328 .unthrottle = mxser_unthrottle,
2329 .set_termios = mxser_set_termios,
2331 .start = mxser_start,
2332 .hangup = mxser_hangup,
2333 .break_ctl = mxser_rs_break,
2334 .wait_until_sent = mxser_wait_until_sent,
2335 .tiocmget = mxser_tiocmget,
2336 .tiocmset = mxser_tiocmset,
2337 .get_icount = mxser_get_icount,
2340 static struct tty_port_operations mxser_port_ops = {
2341 .carrier_raised = mxser_carrier_raised,
2342 .dtr_rts = mxser_dtr_rts,
2343 .activate = mxser_activate,
2344 .shutdown = mxser_shutdown_port,
2348 * The MOXA Smartio/Industio serial driver boot-time initialization code!
2351 static bool allow_overlapping_vector;
2352 module_param(allow_overlapping_vector, bool, S_IRUGO);
2353 MODULE_PARM_DESC(allow_overlapping_vector, "whether we allow ISA cards to be configured such that vector overlabs IO ports (default=no)");
2355 static bool mxser_overlapping_vector(struct mxser_board *brd)
2357 return allow_overlapping_vector &&
2358 brd->vector >= brd->ports[0].ioaddr &&
2359 brd->vector < brd->ports[0].ioaddr + 8 * brd->info->nports;
2362 static int mxser_request_vector(struct mxser_board *brd)
2364 if (mxser_overlapping_vector(brd))
2366 return request_region(brd->vector, 1, "mxser(vector)") ? 0 : -EIO;
2369 static void mxser_release_vector(struct mxser_board *brd)
2371 if (mxser_overlapping_vector(brd))
2373 release_region(brd->vector, 1);
2376 static void mxser_release_ISA_res(struct mxser_board *brd)
2378 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
2379 mxser_release_vector(brd);
2382 static int mxser_initbrd(struct mxser_board *brd,
2383 struct pci_dev *pdev)
2385 struct mxser_port *info;
2389 printk(KERN_INFO "mxser: max. baud rate = %d bps\n",
2390 brd->ports[0].max_baud);
2392 for (i = 0; i < brd->info->nports; i++) {
2393 info = &brd->ports[i];
2394 tty_port_init(&info->port);
2395 info->port.ops = &mxser_port_ops;
2398 info->ldisc_stop_rx = 0;
2400 /* Enhance mode enabled here */
2401 if (brd->chip_flag != MOXA_OTHER_UART)
2402 mxser_enable_must_enchance_mode(info->ioaddr);
2404 info->port.flags = ASYNC_SHARE_IRQ;
2405 info->type = brd->uart_type;
2407 process_txrx_fifo(info);
2409 info->custom_divisor = info->baud_base * 16;
2410 info->port.close_delay = 5 * HZ / 10;
2411 info->port.closing_wait = 30 * HZ;
2412 info->normal_termios = mxvar_sdriver->init_termios;
2413 memset(&info->mon_data, 0, sizeof(struct mxser_mon));
2414 info->err_shadow = 0;
2415 spin_lock_init(&info->slock);
2417 /* before set INT ISR, disable all int */
2418 outb(inb(info->ioaddr + UART_IER) & 0xf0,
2419 info->ioaddr + UART_IER);
2422 retval = request_irq(brd->irq, mxser_interrupt, IRQF_SHARED, "mxser",
2425 for (i = 0; i < brd->info->nports; i++)
2426 tty_port_destroy(&brd->ports[i].port);
2427 printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may "
2428 "conflict with another device.\n",
2429 brd->info->name, brd->irq);
2435 static void mxser_board_remove(struct mxser_board *brd)
2439 for (i = 0; i < brd->info->nports; i++) {
2440 tty_unregister_device(mxvar_sdriver, brd->idx + i);
2441 tty_port_destroy(&brd->ports[i].port);
2443 free_irq(brd->irq, brd);
2446 static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd)
2448 int id, i, bits, ret;
2449 unsigned short regs[16], irq;
2450 unsigned char scratch, scratch2;
2452 brd->chip_flag = MOXA_OTHER_UART;
2454 id = mxser_read_register(cap, regs);
2457 brd->info = &mxser_cards[0];
2460 brd->info = &mxser_cards[1];
2462 case CI104J_ASIC_ID:
2463 brd->info = &mxser_cards[2];
2466 brd->info = &mxser_cards[5];
2469 brd->info = &mxser_cards[6];
2472 brd->info = &mxser_cards[7];
2479 /* some ISA cards have 2 ports, but we want to see them as 4-port (why?)
2480 Flag-hack checks if configuration should be read as 2-port here. */
2481 if (brd->info->nports == 2 || (brd->info->flags & MXSER_HAS2)) {
2482 irq = regs[9] & 0xF000;
2483 irq = irq | (irq >> 4);
2484 if (irq != (regs[9] & 0xFF00))
2485 goto err_irqconflict;
2486 } else if (brd->info->nports == 4) {
2487 irq = regs[9] & 0xF000;
2488 irq = irq | (irq >> 4);
2489 irq = irq | (irq >> 8);
2491 goto err_irqconflict;
2492 } else if (brd->info->nports == 8) {
2493 irq = regs[9] & 0xF000;
2494 irq = irq | (irq >> 4);
2495 irq = irq | (irq >> 8);
2496 if ((irq != regs[9]) || (irq != regs[10]))
2497 goto err_irqconflict;
2501 printk(KERN_ERR "mxser: interrupt number unset\n");
2504 brd->irq = ((int)(irq & 0xF000) >> 12);
2505 for (i = 0; i < 8; i++)
2506 brd->ports[i].ioaddr = (int) regs[i + 1] & 0xFFF8;
2507 if ((regs[12] & 0x80) == 0) {
2508 printk(KERN_ERR "mxser: invalid interrupt vector\n");
2511 brd->vector = (int)regs[11]; /* interrupt vector */
2513 brd->vector_mask = 0x00FF;
2515 brd->vector_mask = 0x000F;
2516 for (i = 7, bits = 0x0100; i >= 0; i--, bits <<= 1) {
2517 if (regs[12] & bits) {
2518 brd->ports[i].baud_base = 921600;
2519 brd->ports[i].max_baud = 921600;
2521 brd->ports[i].baud_base = 115200;
2522 brd->ports[i].max_baud = 115200;
2525 scratch2 = inb(cap + UART_LCR) & (~UART_LCR_DLAB);
2526 outb(scratch2 | UART_LCR_DLAB, cap + UART_LCR);
2527 outb(0, cap + UART_EFR); /* EFR is the same as FCR */
2528 outb(scratch2, cap + UART_LCR);
2529 outb(UART_FCR_ENABLE_FIFO, cap + UART_FCR);
2530 scratch = inb(cap + UART_IIR);
2533 brd->uart_type = PORT_16550A;
2535 brd->uart_type = PORT_16450;
2536 if (!request_region(brd->ports[0].ioaddr, 8 * brd->info->nports,
2538 printk(KERN_ERR "mxser: can't request ports I/O region: "
2539 "0x%.8lx-0x%.8lx\n",
2540 brd->ports[0].ioaddr, brd->ports[0].ioaddr +
2541 8 * brd->info->nports - 1);
2545 ret = mxser_request_vector(brd);
2547 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
2548 printk(KERN_ERR "mxser: can't request interrupt vector region: "
2549 "0x%.8lx-0x%.8lx\n",
2550 brd->ports[0].ioaddr, brd->ports[0].ioaddr +
2551 8 * brd->info->nports - 1);
2554 return brd->info->nports;
2557 printk(KERN_ERR "mxser: invalid interrupt number\n");
2561 static int mxser_probe(struct pci_dev *pdev,
2562 const struct pci_device_id *ent)
2565 struct mxser_board *brd;
2567 unsigned long ioaddress;
2568 struct device *tty_dev;
2569 int retval = -EINVAL;
2571 for (i = 0; i < MXSER_BOARDS; i++)
2572 if (mxser_boards[i].info == NULL)
2575 if (i >= MXSER_BOARDS) {
2576 dev_err(&pdev->dev, "too many boards found (maximum %d), board "
2577 "not configured\n", MXSER_BOARDS);
2581 brd = &mxser_boards[i];
2582 brd->idx = i * MXSER_PORTS_PER_BOARD;
2583 dev_info(&pdev->dev, "found MOXA %s board (BusNo=%d, DevNo=%d)\n",
2584 mxser_cards[ent->driver_data].name,
2585 pdev->bus->number, PCI_SLOT(pdev->devfn));
2587 retval = pci_enable_device(pdev);
2589 dev_err(&pdev->dev, "PCI enable failed\n");
2594 ioaddress = pci_resource_start(pdev, 2);
2595 retval = pci_request_region(pdev, 2, "mxser(IO)");
2599 brd->info = &mxser_cards[ent->driver_data];
2600 for (i = 0; i < brd->info->nports; i++)
2601 brd->ports[i].ioaddr = ioaddress + 8 * i;
2604 ioaddress = pci_resource_start(pdev, 3);
2605 retval = pci_request_region(pdev, 3, "mxser(vector)");
2608 brd->vector = ioaddress;
2611 brd->irq = pdev->irq;
2613 brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr);
2614 brd->uart_type = PORT_16550A;
2615 brd->vector_mask = 0;
2617 for (i = 0; i < brd->info->nports; i++) {
2618 for (j = 0; j < UART_INFO_NUM; j++) {
2619 if (Gpci_uart_info[j].type == brd->chip_flag) {
2620 brd->ports[i].max_baud =
2621 Gpci_uart_info[j].max_baud;
2623 /* exception....CP-102 */
2624 if (brd->info->flags & MXSER_HIGHBAUD)
2625 brd->ports[i].max_baud = 921600;
2631 if (brd->chip_flag == MOXA_MUST_MU860_HWID) {
2632 for (i = 0; i < brd->info->nports; i++) {
2634 brd->ports[i].opmode_ioaddr = ioaddress + 4;
2636 brd->ports[i].opmode_ioaddr = ioaddress + 0x0c;
2638 outb(0, ioaddress + 4); /* default set to RS232 mode */
2639 outb(0, ioaddress + 0x0c); /* default set to RS232 mode */
2642 for (i = 0; i < brd->info->nports; i++) {
2643 brd->vector_mask |= (1 << i);
2644 brd->ports[i].baud_base = 921600;
2647 /* mxser_initbrd will hook ISR. */
2648 retval = mxser_initbrd(brd, pdev);
2652 for (i = 0; i < brd->info->nports; i++) {
2653 tty_dev = tty_port_register_device(&brd->ports[i].port,
2654 mxvar_sdriver, brd->idx + i, &pdev->dev);
2655 if (IS_ERR(tty_dev)) {
2656 retval = PTR_ERR(tty_dev);
2658 tty_unregister_device(mxvar_sdriver,
2664 pci_set_drvdata(pdev, brd);
2668 for (i = 0; i < brd->info->nports; i++)
2669 tty_port_destroy(&brd->ports[i].port);
2670 free_irq(brd->irq, brd);
2672 pci_release_region(pdev, 3);
2675 pci_release_region(pdev, 2);
2677 pci_disable_device(pdev);
2685 static void mxser_remove(struct pci_dev *pdev)
2688 struct mxser_board *brd = pci_get_drvdata(pdev);
2690 mxser_board_remove(brd);
2692 pci_release_region(pdev, 2);
2693 pci_release_region(pdev, 3);
2694 pci_disable_device(pdev);
2699 static struct pci_driver mxser_driver = {
2701 .id_table = mxser_pcibrds,
2702 .probe = mxser_probe,
2703 .remove = mxser_remove
2706 static int __init mxser_module_init(void)
2708 struct mxser_board *brd;
2709 struct device *tty_dev;
2710 unsigned int b, i, m;
2713 mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1);
2717 printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n",
2720 /* Initialize the tty_driver structure */
2721 mxvar_sdriver->name = "ttyMI";
2722 mxvar_sdriver->major = ttymajor;
2723 mxvar_sdriver->minor_start = 0;
2724 mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL;
2725 mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL;
2726 mxvar_sdriver->init_termios = tty_std_termios;
2727 mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL;
2728 mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW|TTY_DRIVER_DYNAMIC_DEV;
2729 tty_set_operations(mxvar_sdriver, &mxser_ops);
2731 retval = tty_register_driver(mxvar_sdriver);
2733 printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family "
2738 /* Start finding ISA boards here */
2739 for (m = 0, b = 0; b < MXSER_BOARDS; b++) {
2743 brd = &mxser_boards[m];
2744 retval = mxser_get_ISA_conf(ioaddr[b], brd);
2750 printk(KERN_INFO "mxser: found MOXA %s board (CAP=0x%lx)\n",
2751 brd->info->name, ioaddr[b]);
2753 /* mxser_initbrd will hook ISR. */
2754 if (mxser_initbrd(brd, NULL) < 0) {
2755 mxser_release_ISA_res(brd);
2760 brd->idx = m * MXSER_PORTS_PER_BOARD;
2761 for (i = 0; i < brd->info->nports; i++) {
2762 tty_dev = tty_port_register_device(&brd->ports[i].port,
2763 mxvar_sdriver, brd->idx + i, NULL);
2764 if (IS_ERR(tty_dev)) {
2766 tty_unregister_device(mxvar_sdriver,
2768 for (i = 0; i < brd->info->nports; i++)
2769 tty_port_destroy(&brd->ports[i].port);
2770 free_irq(brd->irq, brd);
2771 mxser_release_ISA_res(brd);
2776 if (brd->info == NULL)
2782 retval = pci_register_driver(&mxser_driver);
2784 printk(KERN_ERR "mxser: can't register pci driver\n");
2788 } /* else: we have some ISA cards under control */
2793 tty_unregister_driver(mxvar_sdriver);
2795 put_tty_driver(mxvar_sdriver);
2799 static void __exit mxser_module_exit(void)
2803 pci_unregister_driver(&mxser_driver);
2805 for (i = 0; i < MXSER_BOARDS; i++) /* ISA remains */
2806 if (mxser_boards[i].info != NULL)
2807 mxser_board_remove(&mxser_boards[i]);
2808 tty_unregister_driver(mxvar_sdriver);
2809 put_tty_driver(mxvar_sdriver);
2811 for (i = 0; i < MXSER_BOARDS; i++)
2812 if (mxser_boards[i].info != NULL)
2813 mxser_release_ISA_res(&mxser_boards[i]);
2816 module_init(mxser_module_init);
2817 module_exit(mxser_module_exit);