drivers/net/wireless/rockchip_wlan/rtl8188eu/include/Hal8812PwrSeq.h

   1 \r
   2 /******************************************************************************\r
   3  *\r
   4  * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.\r
   5  *\r
   6  * This program is free software; you can redistribute it and/or modify it\r
   7  * under the terms of version 2 of the GNU General Public License as\r
   8  * published by the Free Software Foundation.\r
   9  *\r
  10  * This program is distributed in the hope that it will be useful, but WITHOUT\r
  11  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or\r
  12  * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for\r
  13  * more details.\r
  14  *\r
  15  * You should have received a copy of the GNU General Public License along with\r
  16  * this program; if not, write to the Free Software Foundation, Inc.,\r
  17  * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA\r
  18  *\r
  19  *\r
  20  ******************************************************************************/\r
  21 \r
  22 #ifndef __HAL8812PWRSEQ_H__\r
  23 #define __HAL8812PWRSEQ_H__\r
  24 \r
  25 #include "HalPwrSeqCmd.h"\r
  26 \r
  27 /* \r
  28         Check document WB-110628-DZ-RTL8195 (Jaguar) Power Architecture-R04.pdf\r
  29         There are 6 HW Power States:\r
  30         0: POFF--Power Off\r
  31         1: PDN--Power Down\r
  32         2: CARDEMU--Card Emulation\r
  33         3: ACT--Active Mode\r
  34         4: LPS--Low Power State\r
  35         5: SUS--Suspend\r
  36 \r
  37         The transision from different states are defined below\r
  38         TRANS_CARDEMU_TO_ACT\r
  39         TRANS_ACT_TO_CARDEMU\r
  40         TRANS_CARDEMU_TO_SUS\r
  41         TRANS_SUS_TO_CARDEMU\r
  42         TRANS_CARDEMU_TO_PDN\r
  43         TRANS_ACT_TO_LPS\r
  44         TRANS_LPS_TO_ACT        \r
  45 \r
  46         TRANS_END\r
  47 */\r
  48 #define RTL8812_TRANS_CARDEMU_TO_ACT_STEPS      15\r
  49 #define RTL8812_TRANS_ACT_TO_CARDEMU_STEPS      15\r
  50 #define RTL8812_TRANS_CARDEMU_TO_SUS_STEPS      15\r
  51 #define RTL8812_TRANS_SUS_TO_CARDEMU_STEPS      15\r
  52 #define RTL8812_TRANS_CARDEMU_TO_PDN_STEPS      15\r
  53 #define RTL8812_TRANS_PDN_TO_CARDEMU_STEPS      15\r
  54 #define RTL8812_TRANS_ACT_TO_LPS_STEPS  15\r
  55 #define RTL8812_TRANS_LPS_TO_ACT_STEPS  15      \r
  56 #define RTL8812_TRANS_END_STEPS 1\r
  57 \r
  58 \r
  59 #define RTL8812_TRANS_CARDEMU_TO_ACT                                                                                                            \\r
  60         /* format */                                                                                                                            \\r
  61         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  62         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/* disable SW LPS 0x04[10]=0*/     \\r
  63         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1    power ready*/    \\r
  64         /*{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0}, disable HWPDN 0x04[15]=0*/ \\r
  65         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, 0},/* disable WL suspend*/    \\r
  66         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/     \\r
  67         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/**/\r
  68 \r
  69 #define RTL8812_TRANS_ACT_TO_CARDEMU                                                                                                    \\r
  70         /* format */                                                                                                                            \\r
  71         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  72         {0x0c00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xc00[7:0] = 4      turn off 3-wire */      \\r
  73         {0x0e00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xe00[7:0] = 4      turn off 3-wire */      \\r
  74         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /* 0x2[0] = 0      RESET BB, CLOSE RF */  \\r
  75         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/   \\r
  76         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},  /* Whole BB is reset*/                   \\r
  77         /*{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},//0x1F[7:0] = 0 turn off RF*/    \\r
  78         /*{0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},//0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */      \\r
  79         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x2A}, /* 0x07[7:0] = 0x28 sps pwm mode 0x2a for BT coex*/    \\r
  80         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x02, 0},/*0x8[1] = 0 ANA clk =500k */      \\r
  81         /*{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0|BIT1, 0}, //  0x02[1:0] = 0  reset BB */     \\r
  82         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/       \\r
  83         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/     \r
  84 \r
  85 #define RTL8812_TRANS_CARDEMU_TO_SUS                                                                                                    \\r
  86         /* format */                                                            \\r
  87         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  88         {0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xF0, 0xcc},\\r
  89         {0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xF0, 0xEC},\\r
  90         {0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x07},/* gpio11 input mode, gpio10~8 output mode */   \\r
  91         {0x0045, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio 0~7 output same value as input ?? */    \\r
  92         {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xff},/* gpio0~7 output mode */       \\r
  93         {0x0047, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/* 0x47[7:0] = 00 gpio mode */     \\r
  94         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/* suspend option all off */       \\r
  95         {0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x80, BIT7},/*0x14[7] = 1 turn on ZCD */    \\r
  96         {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x01, BIT0},/* 0x15[0] =1 trun on ZCD */    \\r
  97         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x10, BIT4},/*0x23[4] = 1 hpon LDO sleep mode */    \\r
  98         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x02, 0},/*0x8[1] = 0 ANA clk =500k */      \\r
  99         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, BIT3}, /*0x04[11] = 2b'11 enable WL suspend for PCIe*/        \r
 100 \r
 101 #define RTL8812_TRANS_SUS_TO_CARDEMU                                                                                                    \\r
 102         /* format */                                                            \\r
 103         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 104         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, 0}, /*0x04[11] = 2b'01enable WL suspend*/   \\r
 105         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x10, 0},/*0x23[4] = 0 hpon LDO sleep mode leave */ \\r
 106         {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x01, 0},/* 0x15[0] =0 trun off ZCD */      \\r
 107         {0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x80, 0},/*0x14[7] = 0 turn off ZCD */      \\r
 108         {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio0~7 input mode */        \\r
 109         {0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio11 input mode, gpio10~8 input mode */\r
 110 \r
 111 #define RTL8812_TRANS_CARDEMU_TO_CARDDIS                                                                                                        \\r
 112         /* format */                                                                                                                            \\r
 113         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 114         /**{0x0194, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, //0x194[0]=0 , disable 32K clock*/     \\r
 115         /**{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x94}, //0x93=0x94 , 90[30] =0 enable 500k ANA clock .switch clock from 12M to 500K , 90 [26] =0 disable EEprom loader clock*/     \\r
 116         {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0}, /*0x03[2] = 0, reset 8051*/       \\r
 117         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x05}, /*0x80=05h if reload fw, fill the default value of host_CPU handshake field*/  \\r
 118         {0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xF0, 0xcc},\\r
 119         {0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xF0, 0xEC},\\r
 120         {0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x07},/* gpio11 input mode, gpio10~8 output mode */   \\r
 121         {0x0045, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio 0~7 output same value as input ?? */    \\r
 122         {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xff},/* gpio0~7 output mode */       \\r
 123         {0x0047, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/* 0x47[7:0] = 00 gpio mode */     \\r
 124         {0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x80, BIT7},/*0x14[7] = 1 turn on ZCD */    \\r
 125         {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x01, BIT0},/* 0x15[0] =1 trun on ZCD */    \\r
 126         {0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x01, 0},/*0x12[0] = 0 force PFM mode */    \\r
 127         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x10, BIT4},/*0x23[4] = 1 hpon LDO sleep mode */    \\r
 128         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x02, 0},/*0x8[1] = 0 ANA clk =500k */      \\r
 129         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07=0x20 , SOP option to disable BG/MB*/    \\r
 130         {0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /*0x01f[1]=0 , disable RFC_0  control  REG_RF_CTRL_8812 */        \\r
 131         {0x0076, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /*0x076[1]=0 , disable RFC_1  control REG_OPT_CTRL_8812 +2 */     \\r
 132         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, BIT3}, /*0x04[11] = 2b'01 enable WL suspend*/ \r
 133 \r
 134 #define RTL8812_TRANS_CARDDIS_TO_CARDEMU                                                                                                        \\r
 135         /* format */                                                                                                                            \\r
 136         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                       \\r
 137         {0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*0x12[0] = 1 force PWM mode */ \\r
 138         {0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x80, 0},/*0x14[7] = 0 turn off ZCD */      \\r
 139         {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x01, 0},/* 0x15[0] =0 trun off ZCD */      \\r
 140         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x10, 0},/*0x23[4] = 0 hpon LDO leave sleep mode */ \\r
 141         {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio0~7 input mode */        \\r
 142         {0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio11 input mode, gpio10~8 input mode */ \\r
 143         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0}, /*0x04[10] = 0, enable SW LPS PCIE only*/ \\r
 144         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, 0}, /*0x04[11] = 2b'01enable WL suspend*/     \\r
 145         {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2}, /*0x03[2] = 1, enable 8051*/   \\r
 146         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/\r
 147 \r
 148 \r
 149 #define RTL8812_TRANS_CARDEMU_TO_PDN                                                                                            \\r
 150         /* format */                                                                                                                            \\r
 151         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \\r
 152         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/\r
 153 \r
 154 #define RTL8812_TRANS_PDN_TO_CARDEMU                                                                                            \\r
 155         /* format */                                                                                                                            \\r
 156         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \\r
 157         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/\r
 158 \r
 159 #define RTL8812_TRANS_ACT_TO_LPS                                                                                                                \\r
 160         /* format */                                                                                                                            \\r
 161         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 162         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/       \\r
 163         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/            \\r
 164         {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 165         {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 166         {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 167         {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 168         {0x0c00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xc00[7:0] = 4      turn off 3-wire */      \\r
 169         {0x0e00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xe00[7:0] = 4      turn off 3-wire */      \\r
 170         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated,and RF closed*/    \\r
 171         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/   \\r
 172         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},  /* Whole BB is reset*/                   \\r
 173         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/                       \\r
 174         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/         \\r
 175         {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/   \r
 176 \r
 177 \r
 178 #define RTL8812_TRANS_LPS_TO_ACT                                                                                                                        \\r
 179         /* format */                                                                                                                            \\r
 180         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \\r
 181         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/        \\r
 182         {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/   \\r
 183         {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/  \\r
 184         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/      \\r
 185         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*.       0x08[4] = 0              switch TSF to 40M*/    \\r
 186         {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0  TSF in 40M*/                      \\r
 187         {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6|BIT7, 0}, /*.  0x29[7:6] = 2b'00        enable BB clock*/      \\r
 188         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*.    0x101[1] = 1*/                                  \\r
 189         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*.    0x100[7:0] = 0xFF        enable WMAC TRX*/      \\r
 190         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*.  0x02[1:0] = 2b'11        enable BB macro*/      \\r
 191         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*.       0x522 = 0*/\r
 192  \r
 193 #define RTL8812_TRANS_END                                                                                                                               \\r
 194         /* format */                                                                                                                            \\r
 195         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/         \\r
 196         {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0,PWR_CMD_END, 0, 0}, //\r
 197 \r
 198 \r
 199 extern WLAN_PWR_CFG rtl8812_power_on_flow[RTL8812_TRANS_CARDEMU_TO_ACT_STEPS+RTL8812_TRANS_END_STEPS];\r
 200 extern WLAN_PWR_CFG rtl8812_radio_off_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS+RTL8812_TRANS_END_STEPS];\r
 201 extern WLAN_PWR_CFG rtl8812_card_disable_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS+RTL8812_TRANS_CARDEMU_TO_PDN_STEPS+RTL8812_TRANS_END_STEPS];\r
 202 extern WLAN_PWR_CFG rtl8812_card_enable_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS+RTL8812_TRANS_CARDEMU_TO_PDN_STEPS+RTL8812_TRANS_END_STEPS];\r
 203 extern WLAN_PWR_CFG rtl8812_suspend_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS+RTL8812_TRANS_CARDEMU_TO_SUS_STEPS+RTL8812_TRANS_END_STEPS];\r
 204 extern WLAN_PWR_CFG rtl8812_resume_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS+RTL8812_TRANS_CARDEMU_TO_SUS_STEPS+RTL8812_TRANS_END_STEPS];\r
 205 extern WLAN_PWR_CFG rtl8812_hwpdn_flow[RTL8812_TRANS_ACT_TO_CARDEMU_STEPS+RTL8812_TRANS_CARDEMU_TO_PDN_STEPS+RTL8812_TRANS_END_STEPS];\r
 206 extern WLAN_PWR_CFG rtl8812_enter_lps_flow[RTL8812_TRANS_ACT_TO_LPS_STEPS+RTL8812_TRANS_END_STEPS];\r
 207 extern WLAN_PWR_CFG rtl8812_leave_lps_flow[RTL8812_TRANS_LPS_TO_ACT_STEPS+RTL8812_TRANS_END_STEPS];\r
 208 \r
 209 #endif //__HAL8812PWRSEQ_H__\r
 210 \r