drivers/net/wireless/rockchip_wlan/rtl8188eu/include/Hal8723PwrSeq.h

   1 #ifndef __HAL8723PWRSEQ_H__\r
   2 #define __HAL8723PWRSEQ_H__\r
   3 /*\r
   4         Check document WM-20110607-Paul-RTL8723A_Power_Architecture-R02.vsd\r
   5         There are 6 HW Power States:\r
   6         0: POFF--Power Off\r
   7         1: PDN--Power Down\r
   8         2: CARDEMU--Card Emulation\r
   9         3: ACT--Active Mode\r
  10         4: LPS--Low Power State\r
  11         5: SUS--Suspend\r
  12 \r
  13         The transision from different states are defined below\r
  14         TRANS_CARDEMU_TO_ACT\r
  15         TRANS_ACT_TO_CARDEMU\r
  16         TRANS_CARDEMU_TO_SUS\r
  17         TRANS_SUS_TO_CARDEMU\r
  18         TRANS_CARDEMU_TO_PDN\r
  19         TRANS_ACT_TO_LPS\r
  20         TRANS_LPS_TO_ACT\r
  21 \r
  22         TRANS_END\r
  23 */\r
  24 #include "HalPwrSeqCmd.h"\r
  25 \r
  26 #define RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS     15\r
  27 #define RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS     15\r
  28 #define RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS     15\r
  29 #define RTL8723A_TRANS_SUS_TO_CARDEMU_STEPS     15\r
  30 #define RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS     15\r
  31 #define RTL8723A_TRANS_PDN_TO_CARDEMU_STEPS     15\r
  32 #define RTL8723A_TRANS_ACT_TO_LPS_STEPS 15\r
  33 #define RTL8723A_TRANS_LPS_TO_ACT_STEPS 15\r
  34 #define RTL8723A_TRANS_END_STEPS        1\r
  35 \r
  36 \r
  37 #define RTL8723A_TRANS_CARDEMU_TO_ACT                                                                                                           \\r
  38         /* format */                                                                                                                            \\r
  39         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  40         {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/   \\r
  41         {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/      \\r
  42         {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/   \\r
  43         {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/   \\r
  44         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/* disable SW LPS 0x04[10]=0*/     \\r
  45         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1    power ready*/    \\r
  46         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset  0x04[16]=1*/     \\r
  47         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]=0*/      \\r
  48         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT4|BIT3), 0},/* disable WL suspend*/     \\r
  49         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/     \\r
  50         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/**/     \\r
  51         {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 1},/*0x4C[23] = 0x4E[7] = 1, switch DPDT_SEL_P output from WL BB */\\r
  52 \r
  53 #define RTL8723A_TRANS_ACT_TO_CARDEMU                                                                                                   \\r
  54         /* format */                                                                                                                            \\r
  55         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  56         {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/      \\r
  57         {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/*0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */\\r
  58         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/       \\r
  59         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/     \\r
  60         {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5}, /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/   \\r
  61         {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/   \\r
  62 \r
  63 \r
  64 #define RTL8723A_TRANS_CARDEMU_TO_SUS                                                                                                   \\r
  65         /* format */                                                                                                                            \\r
  66         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  67         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \\r
  68         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/       \\r
  69         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \\r
  70         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/   \\r
  71         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/   \\r
  72         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/  \\r
  73         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/\r
  74 \r
  75 #define RTL8723A_TRANS_SUS_TO_CARDEMU                                                                                                   \\r
  76         /* format */                                                                                                                            \\r
  77         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  78         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/     \\r
  79         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/     \\r
  80         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\\r
  81         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \\r
  82         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\r
  83 \r
  84 #define RTL8723A_TRANS_CARDEMU_TO_CARDDIS                                                                                                       \\r
  85         /* format */                                                                                                                            \\r
  86         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  87         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07=0x20 , SOP option to disable BG/MB*/   \\r
  88         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/       \\r
  89         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2}, /*0x04[10] = 1, enable SW LPS*/        \\r
  90         {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/   \\r
  91         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \\r
  92         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/  \\r
  93         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/\r
  94 \r
  95 #define RTL8723A_TRANS_CARDDIS_TO_CARDEMU                                                                                                       \\r
  96         /* format */                                                                                                                            \\r
  97         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  98         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/     \\r
  99         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/     \\r
 100         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\\r
 101         {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/   \\r
 102         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\\r
 103         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \\r
 104         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/\r
 105 \r
 106 \r
 107 #define RTL8723A_TRANS_CARDEMU_TO_PDN                                                                                           \\r
 108         /* format */                                                                                                                            \\r
 109         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 110         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \\r
 111         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/   \\r
 112         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\\r
 113         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/\r
 114 \r
 115 #define RTL8723A_TRANS_PDN_TO_CARDEMU                                                                                           \\r
 116         /* format */                                                                                                                            \\r
 117         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 118         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/\r
 119 \r
 120 #define RTL8723A_TRANS_ACT_TO_LPS                                                                                                               \\r
 121         /* format */                                                                                                                            \\r
 122         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 123         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/       \\r
 124         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/    \\r
 125         {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 126         {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 127         {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 128         {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 129         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/  \\r
 130         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/   \\r
 131         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/      \\r
 132         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/       \\r
 133         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \\r
 134         {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/  \\r
 135         {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/   \\r
 136 \r
 137 \r
 138 #define RTL8723A_TRANS_LPS_TO_ACT                                                                                                                       \\r
 139         /* format */                                                                                                                            \\r
 140         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 141         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\\r
 142         {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\\r
 143         {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\\r
 144         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\\r
 145         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*.       0x08[4] = 0              switch TSF to 40M*/\\r
 146         {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0  TSF in 40M*/\\r
 147         {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6|BIT7, 0}, /*.  0x29[7:6] = 2b'00        enable BB clock*/\\r
 148         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*.    0x101[1] = 1*/\\r
 149         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*.    0x100[7:0] = 0xFF        enable WMAC TRX*/\\r
 150         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*.  0x02[1:0] = 2b'11        enable BB macro*/\\r
 151         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*.       0x522 = 0*/\r
 152 \r
 153 #define RTL8723A_TRANS_END                                                                                                                      \\r
 154         /* format */                                                                                                                            \\r
 155         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 156         {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0,PWR_CMD_END, 0, 0}, //\r
 157 \r
 158 \r
 159 extern WLAN_PWR_CFG rtl8723A_power_on_flow[RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS+RTL8723A_TRANS_END_STEPS];\r
 160 extern WLAN_PWR_CFG rtl8723A_radio_off_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_END_STEPS];\r
 161 extern WLAN_PWR_CFG rtl8723A_card_disable_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS];\r
 162 extern WLAN_PWR_CFG rtl8723A_card_enable_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS];\r
 163 extern WLAN_PWR_CFG rtl8723A_suspend_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723A_TRANS_END_STEPS];\r
 164 extern WLAN_PWR_CFG rtl8723A_resume_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723A_TRANS_END_STEPS];\r
 165 extern WLAN_PWR_CFG rtl8723A_hwpdn_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS];\r
 166 extern WLAN_PWR_CFG rtl8723A_enter_lps_flow[RTL8723A_TRANS_ACT_TO_LPS_STEPS+RTL8723A_TRANS_END_STEPS];\r
 167 extern WLAN_PWR_CFG rtl8723A_leave_lps_flow[RTL8723A_TRANS_LPS_TO_ACT_STEPS+RTL8723A_TRANS_END_STEPS];\r
 168 \r
 169 #endif\r
 170 \r