drivers/net/wireless/rockchip_wlan/rtl8188eu/include/Hal8723BPwrSeq.h

   1 #ifndef REALTEK_POWER_SEQUENCE_8723B\r
   2 #define REALTEK_POWER_SEQUENCE_8723B\r
   3 \r
   4 #include "HalPwrSeqCmd.h"\r
   5 \r
   6 /* \r
   7         Check document WM-20130815-JackieLau-RTL8723B_Power_Architecture v08.vsd\r
   8         There are 6 HW Power States:\r
   9         0: POFF--Power Off\r
  10         1: PDN--Power Down\r
  11         2: CARDEMU--Card Emulation\r
  12         3: ACT--Active Mode\r
  13         4: LPS--Low Power State\r
  14         5: SUS--Suspend\r
  15 \r
  16         The transision from different states are defined below\r
  17         TRANS_CARDEMU_TO_ACT\r
  18         TRANS_ACT_TO_CARDEMU\r
  19         TRANS_CARDEMU_TO_SUS\r
  20         TRANS_SUS_TO_CARDEMU\r
  21         TRANS_CARDEMU_TO_PDN\r
  22         TRANS_ACT_TO_LPS\r
  23         TRANS_LPS_TO_ACT        \r
  24 \r
  25         TRANS_END\r
  26 */\r
  27 #define RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS     26\r
  28 #define RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS     15\r
  29 #define RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS     15\r
  30 #define RTL8723B_TRANS_SUS_TO_CARDEMU_STEPS     15\r
  31 #define RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS     15\r
  32 #define RTL8723B_TRANS_PDN_TO_CARDEMU_STEPS     15\r
  33 #define RTL8723B_TRANS_ACT_TO_LPS_STEPS         15\r
  34 #define RTL8723B_TRANS_LPS_TO_ACT_STEPS         15      \r
  35 #define RTL8723B_TRANS_ACT_TO_SWLPS_STEPS               22\r
  36 #define RTL8723B_TRANS_SWLPS_TO_ACT_STEPS               15\r
  37 #define RTL8723B_TRANS_END_STEPS                1\r
  38 \r
  39 \r
  40 #define RTL8723B_TRANS_CARDEMU_TO_ACT                                                                                                           \\r
  41         /* format */                                                                                                                            \\r
  42         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  43         {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/   \\r
  44         {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/      \\r
  45         {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/   \\r
  46         {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/   \\r
  47         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT4|BIT3|BIT2), 0},/* disable SW LPS 0x04[10]=0 and WLSUS_EN 0x04[11]=0*/ \\r
  48         {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0 , BIT0},/* Disable USB suspend */      \\r
  49         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1    power ready*/    \\r
  50         {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0 , 0},/* Enable USB suspend */  \\r
  51         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset  0x04[16]=1*/     \\r
  52         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]=0*/      \\r
  53         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT4|BIT3), 0},/* disable WL suspend*/     \\r
  54         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/     \\r
  55         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/**/     \\r
  56         {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/* Enable WL control XTAL setting*/     \\r
  57         {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/*Enable falling edge triggering interrupt*/\\r
  58         {0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/*Enable GPIO9 interrupt mode*/\\r
  59         {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Enable GPIO9 input mode*/\\r
  60         {0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Enable HSISR GPIO[C:0] interrupt*/\\r
  61         {0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/*Enable HSISR GPIO9 interrupt*/\\r
  62         {0x0068, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, BIT3},/*For GPIO9 internal pull high setting by test chip*/\\r
  63         {0x0069, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/*For GPIO9 internal pull high setting*/\\r
  64 \r
  65 \r
  66 #define RTL8723B_TRANS_ACT_TO_CARDEMU                                                                                                   \\r
  67         /* format */                                                                                                                            \\r
  68         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  69         {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/      \\r
  70         {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Enable rising edge triggering interrupt*/ \\r
  71         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset  0x04[16]=1*/     \\r
  72         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/       \\r
  73         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/     \\r
  74         {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, 0},/* Enable BT control XTAL setting*/\\r
  75         {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5}, /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/   \\r
  76         {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/\\r
  77 \r
  78 \r
  79 #define RTL8723B_TRANS_CARDEMU_TO_SUS                                                                                                   \\r
  80         /* format */                                                                                                                            \\r
  81         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  82         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \\r
  83         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/       \\r
  84         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \\r
  85         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/   \\r
  86         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/   \\r
  87         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/  \\r
  88         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/\r
  89 \r
  90 #define RTL8723B_TRANS_SUS_TO_CARDEMU                                                                                                   \\r
  91         /* format */                                                                                                                            \\r
  92         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
  93         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/     \\r
  94         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/     \\r
  95         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\\r
  96         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \\r
  97         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\r
  98 \r
  99 #define RTL8723B_TRANS_CARDEMU_TO_CARDDIS                                                                                                       \\r
 100         /* format */                                                                                                                            \\r
 101         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 102         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07=0x20 , SOP option to disable BG/MB*/   \\r
 103         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/       \\r
 104         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2}, /*0x04[10] = 1, enable SW LPS*/        \\r
 105         {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/   \\r
 106         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \\r
 107         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/  \\r
 108         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/\r
 109 \r
 110 #define RTL8723B_TRANS_CARDDIS_TO_CARDEMU                                                                                                       \\r
 111         /* format */                                                                                                                            \\r
 112         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 113         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/     \\r
 114         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/     \\r
 115         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\\r
 116         {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/   \\r
 117         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\\r
 118         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \\r
 119         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/\r
 120 \r
 121 \r
 122 #define RTL8723B_TRANS_CARDEMU_TO_PDN                                                                                           \\r
 123         /* format */                                                                                                                            \\r
 124         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 125         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \\r
 126         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/   \\r
 127         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\\r
 128         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/\r
 129 \r
 130 #define RTL8723B_TRANS_PDN_TO_CARDEMU                                                                                           \\r
 131         /* format */                                                                                                                            \\r
 132         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 133         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/\r
 134 \r
 135 #define RTL8723B_TRANS_ACT_TO_LPS                                                                                                               \\r
 136         /* format */                                                                                                                            \\r
 137         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 138         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/       \\r
 139         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/    \\r
 140         {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 141         {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 142         {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 143         {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/  \\r
 144         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/  \\r
 145         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/   \\r
 146         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/      \\r
 147         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/       \\r
 148         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \\r
 149         {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/  \\r
 150         {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/   \\r
 151 \r
 152 \r
 153 #define RTL8723B_TRANS_LPS_TO_ACT                                                                                                                       \\r
 154         /* format */                                                                                                                            \\r
 155         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 156         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\\r
 157         {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\\r
 158         {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\\r
 159         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\\r
 160         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*.       0x08[4] = 0              switch TSF to 40M*/\\r
 161         {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0  TSF in 40M*/\\r
 162         {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6|BIT7, 0}, /*.  0x29[7:6] = 2b'00        enable BB clock*/\\r
 163         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*.    0x101[1] = 1*/\\r
 164         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*.    0x100[7:0] = 0xFF        enable WMAC TRX*/\\r
 165         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*.  0x02[1:0] = 2b'11        enable BB macro*/\\r
 166         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*.       0x522 = 0*/\r
 167  \r
 168  \r
 169  #define RTL8723B_TRANS_ACT_TO_SWLPS                                                                                                            \\r
 170         /* format */                                                                                                                            \\r
 171         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 172         {0x0194, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*enable 32 K source*/ \\r
 173         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/ \\r
 174         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/       \\r
 175         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/ \\r
 176         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/       \\r
 177         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/ \\r
 178         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/      \\r
 179         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*disable security engine*/       \\r
 180         {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x40},/*When driver enter Sus/ Disable, enable LOP for BT*/  \\r
 181         {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*reset dual TSF*/     \\r
 182         {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/*Reset CPU*/     \\r
 183         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*Reset MCUFWDL register*/        \\r
 184         {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/  \\r
 185         {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},/*Reset CPU IO Wrapper*/  \\r
 186         {0x0287, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*polling RXFF packet number = 0 */     \\r
 187         {0x0286, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/*polling RXDMA idle */      \\r
 188         {0x013D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Clear FW RPWM interrupt */\\r
 189         {0x0139, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Set FW RPWM interrupt source*/\\r
 190         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4},/*switch TSF to 32K*/\\r
 191         {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/*polling TSF stable*/\\r
 192         {0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Set FW LPS*/ \\r
 193         {0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/*polling FW LPS ready */       \r
 194 \r
 195 \r
 196 #define RTL8723B_TRANS_SWLPS_TO_ACT                                                                                                                     \\r
 197         /* format */                                                                                                                            \\r
 198         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 199         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0},/*switch TSF to 32K*/\\r
 200         {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/*polling TSF stable*/\\r
 201         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*.   0x101[1] = 1, enable security engine*/\\r
 202         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*.   0x100[7:0] = 0xFF        enable WMAC TRX*/\\r
 203         {0x06B7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x09}, /*.   reset MAC rx state machine*/\\r
 204         {0x06B4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x86}, /*.   reset MAC rx state machine*/\\r
 205         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/* set CPU RAM code ready*/    \\r
 206         {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/  \\r
 207         {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/* Enable CPU*/   \\r
 208         {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*enable CPU IO Wrapper*/      \\r
 209         {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2},/* Enable CPU*/        \\r
 210         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, BIT7},/*polling FW init ready */   \\r
 211         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT6, BIT6},/*polling FW init ready */   \\r
 212         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /*.   0x02[1:0] = 2b'11        enable BB macro*/\\r
 213         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*.      0x522 = 0*/\r
 214         \r
 215 #define RTL8723B_TRANS_END                                                                                                                      \\r
 216         /* format */                                                                                                                            \\r
 217         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/                                                         \\r
 218         {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0,PWR_CMD_END, 0, 0}, //\r
 219 \r
 220 \r
 221 extern WLAN_PWR_CFG rtl8723B_power_on_flow[RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS+RTL8723B_TRANS_END_STEPS];\r
 222 extern WLAN_PWR_CFG rtl8723B_radio_off_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_END_STEPS];\r
 223 extern WLAN_PWR_CFG rtl8723B_card_disable_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723B_TRANS_END_STEPS];\r
 224 extern WLAN_PWR_CFG rtl8723B_card_enable_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723B_TRANS_END_STEPS];\r
 225 extern WLAN_PWR_CFG rtl8723B_suspend_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723B_TRANS_END_STEPS];\r
 226 extern WLAN_PWR_CFG rtl8723B_resume_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723B_TRANS_END_STEPS];\r
 227 extern WLAN_PWR_CFG rtl8723B_hwpdn_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723B_TRANS_END_STEPS];\r
 228 extern WLAN_PWR_CFG rtl8723B_enter_lps_flow[RTL8723B_TRANS_ACT_TO_LPS_STEPS+RTL8723B_TRANS_END_STEPS];\r
 229 extern WLAN_PWR_CFG rtl8723B_leave_lps_flow[RTL8723B_TRANS_LPS_TO_ACT_STEPS+RTL8723B_TRANS_END_STEPS];\r
 230 extern WLAN_PWR_CFG rtl8723B_enter_swlps_flow[RTL8723B_TRANS_ACT_TO_SWLPS_STEPS+RTL8723B_TRANS_END_STEPS];\r
 231 extern WLAN_PWR_CFG rtl8723B_leave_swlps_flow[RTL8723B_TRANS_SWLPS_TO_ACT_STEPS+RTL8723B_TRANS_END_STEPS];\r
 232 #endif\r
 233 \r