1 /***************************************************************************
3 * Copyright (C) 2004-2008 SMSC
4 * Copyright (C) 2005-2008 ARM
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License
8 * as published by the Free Software Foundation; either version 2
9 * of the License, or (at your option) any later version.
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, see <http://www.gnu.org/licenses/>.
19 ***************************************************************************
20 * Rewritten, heavily based on smsc911x simple driver by SMSC.
21 * Partly uses io macros from smc91x.c by Nicolas Pitre
24 * LAN9115, LAN9116, LAN9117, LAN9118
25 * LAN9215, LAN9216, LAN9217, LAN9218
32 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
34 #include <linux/crc32.h>
35 #include <linux/clk.h>
36 #include <linux/delay.h>
37 #include <linux/errno.h>
38 #include <linux/etherdevice.h>
39 #include <linux/ethtool.h>
40 #include <linux/init.h>
41 #include <linux/interrupt.h>
42 #include <linux/ioport.h>
43 #include <linux/kernel.h>
44 #include <linux/module.h>
45 #include <linux/netdevice.h>
46 #include <linux/platform_device.h>
47 #include <linux/regulator/consumer.h>
48 #include <linux/sched.h>
49 #include <linux/timer.h>
50 #include <linux/bug.h>
51 #include <linux/bitops.h>
52 #include <linux/irq.h>
54 #include <linux/swab.h>
55 #include <linux/phy.h>
56 #include <linux/smsc911x.h>
57 #include <linux/device.h>
59 #include <linux/of_device.h>
60 #include <linux/of_gpio.h>
61 #include <linux/of_net.h>
62 #include <linux/acpi.h>
63 #include <linux/pm_runtime.h>
64 #include <linux/property.h>
68 #define SMSC_CHIPNAME "smsc911x"
69 #define SMSC_MDIONAME "smsc911x-mdio"
70 #define SMSC_DRV_VERSION "2008-10-21"
72 MODULE_LICENSE("GPL");
73 MODULE_VERSION(SMSC_DRV_VERSION);
74 MODULE_ALIAS("platform:smsc911x");
77 static int debug = 16;
82 module_param(debug, int, 0);
83 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
88 u32 (*reg_read)(struct smsc911x_data *pdata, u32 reg);
89 void (*reg_write)(struct smsc911x_data *pdata, u32 reg, u32 val);
90 void (*rx_readfifo)(struct smsc911x_data *pdata,
91 unsigned int *buf, unsigned int wordcount);
92 void (*tx_writefifo)(struct smsc911x_data *pdata,
93 unsigned int *buf, unsigned int wordcount);
96 #define SMSC911X_NUM_SUPPLIES 2
98 struct smsc911x_data {
103 /* used to decide which workarounds apply */
104 unsigned int generation;
106 /* device configuration (copied from platform_data during probe) */
107 struct smsc911x_platform_config config;
109 /* This needs to be acquired before calling any of below:
110 * smsc911x_mac_read(), smsc911x_mac_write()
114 /* spinlock to ensure register accesses are serialised */
117 struct phy_device *phy_dev;
118 struct mii_bus *mii_bus;
119 int phy_irq[PHY_MAX_ADDR];
120 unsigned int using_extphy;
125 unsigned int gpio_setting;
126 unsigned int gpio_orig_setting;
127 struct net_device *dev;
128 struct napi_struct napi;
130 unsigned int software_irq_signal;
132 #ifdef USE_PHY_WORK_AROUND
133 #define MIN_PACKET_SIZE (64)
134 char loopback_tx_pkt[MIN_PACKET_SIZE];
135 char loopback_rx_pkt[MIN_PACKET_SIZE];
136 unsigned int resetcount;
139 /* Members for Multicast filter workaround */
140 unsigned int multicast_update_pending;
141 unsigned int set_bits_mask;
142 unsigned int clear_bits_mask;
146 /* register access functions */
147 const struct smsc911x_ops *ops;
150 struct regulator_bulk_data supplies[SMSC911X_NUM_SUPPLIES];
156 /* Easy access to information */
157 #define __smsc_shift(pdata, reg) ((reg) << ((pdata)->config.shift))
159 static inline u32 __smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
161 if (pdata->config.flags & SMSC911X_USE_32BIT)
162 return readl(pdata->ioaddr + reg);
164 if (pdata->config.flags & SMSC911X_USE_16BIT)
165 return ((readw(pdata->ioaddr + reg) & 0xFFFF) |
166 ((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16));
173 __smsc911x_reg_read_shift(struct smsc911x_data *pdata, u32 reg)
175 if (pdata->config.flags & SMSC911X_USE_32BIT)
176 return readl(pdata->ioaddr + __smsc_shift(pdata, reg));
178 if (pdata->config.flags & SMSC911X_USE_16BIT)
179 return (readw(pdata->ioaddr +
180 __smsc_shift(pdata, reg)) & 0xFFFF) |
181 ((readw(pdata->ioaddr +
182 __smsc_shift(pdata, reg + 2)) & 0xFFFF) << 16);
188 static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
193 spin_lock_irqsave(&pdata->dev_lock, flags);
194 data = pdata->ops->reg_read(pdata, reg);
195 spin_unlock_irqrestore(&pdata->dev_lock, flags);
200 static inline void __smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg,
203 if (pdata->config.flags & SMSC911X_USE_32BIT) {
204 writel(val, pdata->ioaddr + reg);
208 if (pdata->config.flags & SMSC911X_USE_16BIT) {
209 writew(val & 0xFFFF, pdata->ioaddr + reg);
210 writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2);
218 __smsc911x_reg_write_shift(struct smsc911x_data *pdata, u32 reg, u32 val)
220 if (pdata->config.flags & SMSC911X_USE_32BIT) {
221 writel(val, pdata->ioaddr + __smsc_shift(pdata, reg));
225 if (pdata->config.flags & SMSC911X_USE_16BIT) {
227 pdata->ioaddr + __smsc_shift(pdata, reg));
228 writew((val >> 16) & 0xFFFF,
229 pdata->ioaddr + __smsc_shift(pdata, reg + 2));
236 static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg,
241 spin_lock_irqsave(&pdata->dev_lock, flags);
242 pdata->ops->reg_write(pdata, reg, val);
243 spin_unlock_irqrestore(&pdata->dev_lock, flags);
246 /* Writes a packet to the TX_DATA_FIFO */
248 smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
249 unsigned int wordcount)
253 spin_lock_irqsave(&pdata->dev_lock, flags);
255 if (pdata->config.flags & SMSC911X_SWAP_FIFO) {
257 __smsc911x_reg_write(pdata, TX_DATA_FIFO,
262 if (pdata->config.flags & SMSC911X_USE_32BIT) {
263 iowrite32_rep(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount);
267 if (pdata->config.flags & SMSC911X_USE_16BIT) {
269 __smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++);
275 spin_unlock_irqrestore(&pdata->dev_lock, flags);
278 /* Writes a packet to the TX_DATA_FIFO - shifted version */
280 smsc911x_tx_writefifo_shift(struct smsc911x_data *pdata, unsigned int *buf,
281 unsigned int wordcount)
285 spin_lock_irqsave(&pdata->dev_lock, flags);
287 if (pdata->config.flags & SMSC911X_SWAP_FIFO) {
289 __smsc911x_reg_write_shift(pdata, TX_DATA_FIFO,
294 if (pdata->config.flags & SMSC911X_USE_32BIT) {
295 iowrite32_rep(pdata->ioaddr + __smsc_shift(pdata,
296 TX_DATA_FIFO), buf, wordcount);
300 if (pdata->config.flags & SMSC911X_USE_16BIT) {
302 __smsc911x_reg_write_shift(pdata,
303 TX_DATA_FIFO, *buf++);
309 spin_unlock_irqrestore(&pdata->dev_lock, flags);
312 /* Reads a packet out of the RX_DATA_FIFO */
314 smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
315 unsigned int wordcount)
319 spin_lock_irqsave(&pdata->dev_lock, flags);
321 if (pdata->config.flags & SMSC911X_SWAP_FIFO) {
323 *buf++ = swab32(__smsc911x_reg_read(pdata,
328 if (pdata->config.flags & SMSC911X_USE_32BIT) {
329 ioread32_rep(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount);
333 if (pdata->config.flags & SMSC911X_USE_16BIT) {
335 *buf++ = __smsc911x_reg_read(pdata, RX_DATA_FIFO);
341 spin_unlock_irqrestore(&pdata->dev_lock, flags);
344 /* Reads a packet out of the RX_DATA_FIFO - shifted version */
346 smsc911x_rx_readfifo_shift(struct smsc911x_data *pdata, unsigned int *buf,
347 unsigned int wordcount)
351 spin_lock_irqsave(&pdata->dev_lock, flags);
353 if (pdata->config.flags & SMSC911X_SWAP_FIFO) {
355 *buf++ = swab32(__smsc911x_reg_read_shift(pdata,
360 if (pdata->config.flags & SMSC911X_USE_32BIT) {
361 ioread32_rep(pdata->ioaddr + __smsc_shift(pdata,
362 RX_DATA_FIFO), buf, wordcount);
366 if (pdata->config.flags & SMSC911X_USE_16BIT) {
368 *buf++ = __smsc911x_reg_read_shift(pdata,
375 spin_unlock_irqrestore(&pdata->dev_lock, flags);
379 * enable regulator and clock resources.
381 static int smsc911x_enable_resources(struct platform_device *pdev)
383 struct net_device *ndev = platform_get_drvdata(pdev);
384 struct smsc911x_data *pdata = netdev_priv(ndev);
387 ret = regulator_bulk_enable(ARRAY_SIZE(pdata->supplies),
390 netdev_err(ndev, "failed to enable regulators %d\n",
393 if (!IS_ERR(pdata->clk)) {
394 ret = clk_prepare_enable(pdata->clk);
396 netdev_err(ndev, "failed to enable clock %d\n", ret);
403 * disable resources, currently just regulators.
405 static int smsc911x_disable_resources(struct platform_device *pdev)
407 struct net_device *ndev = platform_get_drvdata(pdev);
408 struct smsc911x_data *pdata = netdev_priv(ndev);
411 ret = regulator_bulk_disable(ARRAY_SIZE(pdata->supplies),
414 if (!IS_ERR(pdata->clk))
415 clk_disable_unprepare(pdata->clk);
421 * Request resources, currently just regulators.
423 * The SMSC911x has two power pins: vddvario and vdd33a, in designs where
424 * these are not always-on we need to request regulators to be turned on
425 * before we can try to access the device registers.
427 static int smsc911x_request_resources(struct platform_device *pdev)
429 struct net_device *ndev = platform_get_drvdata(pdev);
430 struct smsc911x_data *pdata = netdev_priv(ndev);
433 /* Request regulators */
434 pdata->supplies[0].supply = "vdd33a";
435 pdata->supplies[1].supply = "vddvario";
436 ret = regulator_bulk_get(&pdev->dev,
437 ARRAY_SIZE(pdata->supplies),
440 netdev_err(ndev, "couldn't get regulators %d\n",
444 pdata->clk = clk_get(&pdev->dev, NULL);
445 if (IS_ERR(pdata->clk))
446 dev_dbg(&pdev->dev, "couldn't get clock %li\n",
447 PTR_ERR(pdata->clk));
453 * Free resources, currently just regulators.
456 static void smsc911x_free_resources(struct platform_device *pdev)
458 struct net_device *ndev = platform_get_drvdata(pdev);
459 struct smsc911x_data *pdata = netdev_priv(ndev);
461 /* Free regulators */
462 regulator_bulk_free(ARRAY_SIZE(pdata->supplies),
466 if (!IS_ERR(pdata->clk)) {
472 /* waits for MAC not busy, with timeout. Only called by smsc911x_mac_read
473 * and smsc911x_mac_write, so assumes mac_lock is held */
474 static int smsc911x_mac_complete(struct smsc911x_data *pdata)
479 SMSC_ASSERT_MAC_LOCK(pdata);
481 for (i = 0; i < 40; i++) {
482 val = smsc911x_reg_read(pdata, MAC_CSR_CMD);
483 if (!(val & MAC_CSR_CMD_CSR_BUSY_))
486 SMSC_WARN(pdata, hw, "Timed out waiting for MAC not BUSY. "
487 "MAC_CSR_CMD: 0x%08X", val);
491 /* Fetches a MAC register value. Assumes mac_lock is acquired */
492 static u32 smsc911x_mac_read(struct smsc911x_data *pdata, unsigned int offset)
496 SMSC_ASSERT_MAC_LOCK(pdata);
498 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD);
499 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) {
500 SMSC_WARN(pdata, hw, "MAC busy at entry");
504 /* Send the MAC cmd */
505 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) |
506 MAC_CSR_CMD_CSR_BUSY_ | MAC_CSR_CMD_R_NOT_W_));
508 /* Workaround for hardware read-after-write restriction */
509 temp = smsc911x_reg_read(pdata, BYTE_TEST);
511 /* Wait for the read to complete */
512 if (likely(smsc911x_mac_complete(pdata) == 0))
513 return smsc911x_reg_read(pdata, MAC_CSR_DATA);
515 SMSC_WARN(pdata, hw, "MAC busy after read");
519 /* Set a mac register, mac_lock must be acquired before calling */
520 static void smsc911x_mac_write(struct smsc911x_data *pdata,
521 unsigned int offset, u32 val)
525 SMSC_ASSERT_MAC_LOCK(pdata);
527 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD);
528 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) {
530 "smsc911x_mac_write failed, MAC busy at entry");
534 /* Send data to write */
535 smsc911x_reg_write(pdata, MAC_CSR_DATA, val);
537 /* Write the actual data */
538 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) |
539 MAC_CSR_CMD_CSR_BUSY_));
541 /* Workaround for hardware read-after-write restriction */
542 temp = smsc911x_reg_read(pdata, BYTE_TEST);
544 /* Wait for the write to complete */
545 if (likely(smsc911x_mac_complete(pdata) == 0))
548 SMSC_WARN(pdata, hw, "smsc911x_mac_write failed, MAC busy after write");
551 /* Get a phy register */
552 static int smsc911x_mii_read(struct mii_bus *bus, int phyaddr, int regidx)
554 struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv;
559 spin_lock_irqsave(&pdata->mac_lock, flags);
561 /* Confirm MII not busy */
562 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) {
563 SMSC_WARN(pdata, hw, "MII is busy in smsc911x_mii_read???");
568 /* Set the address, index & direction (read from PHY) */
569 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6);
570 smsc911x_mac_write(pdata, MII_ACC, addr);
572 /* Wait for read to complete w/ timeout */
573 for (i = 0; i < 100; i++)
574 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) {
575 reg = smsc911x_mac_read(pdata, MII_DATA);
579 SMSC_WARN(pdata, hw, "Timed out waiting for MII read to finish");
583 spin_unlock_irqrestore(&pdata->mac_lock, flags);
587 /* Set a phy register */
588 static int smsc911x_mii_write(struct mii_bus *bus, int phyaddr, int regidx,
591 struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv;
596 spin_lock_irqsave(&pdata->mac_lock, flags);
598 /* Confirm MII not busy */
599 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) {
600 SMSC_WARN(pdata, hw, "MII is busy in smsc911x_mii_write???");
605 /* Put the data to write in the MAC */
606 smsc911x_mac_write(pdata, MII_DATA, val);
608 /* Set the address, index & direction (write to PHY) */
609 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6) |
611 smsc911x_mac_write(pdata, MII_ACC, addr);
613 /* Wait for write to complete w/ timeout */
614 for (i = 0; i < 100; i++)
615 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) {
620 SMSC_WARN(pdata, hw, "Timed out waiting for MII write to finish");
624 spin_unlock_irqrestore(&pdata->mac_lock, flags);
628 /* Switch to external phy. Assumes tx and rx are stopped. */
629 static void smsc911x_phy_enable_external(struct smsc911x_data *pdata)
631 unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG);
633 /* Disable phy clocks to the MAC */
634 hwcfg &= (~HW_CFG_PHY_CLK_SEL_);
635 hwcfg |= HW_CFG_PHY_CLK_SEL_CLK_DIS_;
636 smsc911x_reg_write(pdata, HW_CFG, hwcfg);
637 udelay(10); /* Enough time for clocks to stop */
639 /* Switch to external phy */
640 hwcfg |= HW_CFG_EXT_PHY_EN_;
641 smsc911x_reg_write(pdata, HW_CFG, hwcfg);
643 /* Enable phy clocks to the MAC */
644 hwcfg &= (~HW_CFG_PHY_CLK_SEL_);
645 hwcfg |= HW_CFG_PHY_CLK_SEL_EXT_PHY_;
646 smsc911x_reg_write(pdata, HW_CFG, hwcfg);
647 udelay(10); /* Enough time for clocks to restart */
649 hwcfg |= HW_CFG_SMI_SEL_;
650 smsc911x_reg_write(pdata, HW_CFG, hwcfg);
653 /* Autodetects and enables external phy if present on supported chips.
654 * autodetection can be overridden by specifying SMSC911X_FORCE_INTERNAL_PHY
655 * or SMSC911X_FORCE_EXTERNAL_PHY in the platform_data flags. */
656 static void smsc911x_phy_initialise_external(struct smsc911x_data *pdata)
658 unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG);
660 if (pdata->config.flags & SMSC911X_FORCE_INTERNAL_PHY) {
661 SMSC_TRACE(pdata, hw, "Forcing internal PHY");
662 pdata->using_extphy = 0;
663 } else if (pdata->config.flags & SMSC911X_FORCE_EXTERNAL_PHY) {
664 SMSC_TRACE(pdata, hw, "Forcing external PHY");
665 smsc911x_phy_enable_external(pdata);
666 pdata->using_extphy = 1;
667 } else if (hwcfg & HW_CFG_EXT_PHY_DET_) {
668 SMSC_TRACE(pdata, hw,
669 "HW_CFG EXT_PHY_DET set, using external PHY");
670 smsc911x_phy_enable_external(pdata);
671 pdata->using_extphy = 1;
673 SMSC_TRACE(pdata, hw,
674 "HW_CFG EXT_PHY_DET clear, using internal PHY");
675 pdata->using_extphy = 0;
679 /* Fetches a tx status out of the status fifo */
680 static unsigned int smsc911x_tx_get_txstatus(struct smsc911x_data *pdata)
682 unsigned int result =
683 smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TSUSED_;
686 result = smsc911x_reg_read(pdata, TX_STATUS_FIFO);
691 /* Fetches the next rx status */
692 static unsigned int smsc911x_rx_get_rxstatus(struct smsc911x_data *pdata)
694 unsigned int result =
695 smsc911x_reg_read(pdata, RX_FIFO_INF) & RX_FIFO_INF_RXSUSED_;
698 result = smsc911x_reg_read(pdata, RX_STATUS_FIFO);
703 #ifdef USE_PHY_WORK_AROUND
704 static int smsc911x_phy_check_loopbackpkt(struct smsc911x_data *pdata)
711 for (tries = 0; tries < 10; tries++) {
712 unsigned int txcmd_a;
713 unsigned int txcmd_b;
715 unsigned int pktlength;
718 /* Zero-out rx packet memory */
719 memset(pdata->loopback_rx_pkt, 0, MIN_PACKET_SIZE);
721 /* Write tx packet to 118 */
722 txcmd_a = (u32)((ulong)pdata->loopback_tx_pkt & 0x03) << 16;
723 txcmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_;
724 txcmd_a |= MIN_PACKET_SIZE;
726 txcmd_b = MIN_PACKET_SIZE << 16 | MIN_PACKET_SIZE;
728 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_a);
729 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_b);
731 bufp = (ulong)pdata->loopback_tx_pkt & (~0x3);
732 wrsz = MIN_PACKET_SIZE + 3;
733 wrsz += (u32)((ulong)pdata->loopback_tx_pkt & 0x3);
736 pdata->ops->tx_writefifo(pdata, (unsigned int *)bufp, wrsz);
738 /* Wait till transmit is done */
742 status = smsc911x_tx_get_txstatus(pdata);
743 } while ((i--) && (!status));
747 "Failed to transmit during loopback test");
750 if (status & TX_STS_ES_) {
752 "Transmit encountered errors during loopback test");
756 /* Wait till receive is done */
760 status = smsc911x_rx_get_rxstatus(pdata);
761 } while ((i--) && (!status));
765 "Failed to receive during loopback test");
768 if (status & RX_STS_ES_) {
770 "Receive encountered errors during loopback test");
774 pktlength = ((status & 0x3FFF0000UL) >> 16);
775 bufp = (ulong)pdata->loopback_rx_pkt;
776 rdsz = pktlength + 3;
777 rdsz += (u32)((ulong)pdata->loopback_rx_pkt & 0x3);
780 pdata->ops->rx_readfifo(pdata, (unsigned int *)bufp, rdsz);
782 if (pktlength != (MIN_PACKET_SIZE + 4)) {
783 SMSC_WARN(pdata, hw, "Unexpected packet size "
784 "during loop back test, size=%d, will retry",
789 for (j = 0; j < MIN_PACKET_SIZE; j++) {
790 if (pdata->loopback_tx_pkt[j]
791 != pdata->loopback_rx_pkt[j]) {
797 SMSC_TRACE(pdata, hw, "Successfully verified "
801 SMSC_WARN(pdata, hw, "Data mismatch "
802 "during loop back test, will retry");
810 static int smsc911x_phy_reset(struct smsc911x_data *pdata)
812 struct phy_device *phy_dev = pdata->phy_dev;
814 unsigned int i = 100000;
817 BUG_ON(!phy_dev->bus);
819 SMSC_TRACE(pdata, hw, "Performing PHY BCR Reset");
820 smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, BMCR_RESET);
823 temp = smsc911x_mii_read(phy_dev->bus, phy_dev->addr,
825 } while ((i--) && (temp & BMCR_RESET));
827 if (temp & BMCR_RESET) {
828 SMSC_WARN(pdata, hw, "PHY reset failed to complete");
831 /* Extra delay required because the phy may not be completed with
832 * its reset when BMCR_RESET is cleared. Specs say 256 uS is
833 * enough delay but using 1ms here to be safe */
839 static int smsc911x_phy_loopbacktest(struct net_device *dev)
841 struct smsc911x_data *pdata = netdev_priv(dev);
842 struct phy_device *phy_dev = pdata->phy_dev;
847 /* Initialise tx packet using broadcast destination address */
848 eth_broadcast_addr(pdata->loopback_tx_pkt);
850 /* Use incrementing source address */
851 for (i = 6; i < 12; i++)
852 pdata->loopback_tx_pkt[i] = (char)i;
854 /* Set length type field */
855 pdata->loopback_tx_pkt[12] = 0x00;
856 pdata->loopback_tx_pkt[13] = 0x00;
858 for (i = 14; i < MIN_PACKET_SIZE; i++)
859 pdata->loopback_tx_pkt[i] = (char)i;
861 val = smsc911x_reg_read(pdata, HW_CFG);
862 val &= HW_CFG_TX_FIF_SZ_;
864 smsc911x_reg_write(pdata, HW_CFG, val);
866 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_);
867 smsc911x_reg_write(pdata, RX_CFG,
868 (u32)((ulong)pdata->loopback_rx_pkt & 0x03) << 8);
870 for (i = 0; i < 10; i++) {
871 /* Set PHY to 10/FD, no ANEG, and loopback mode */
872 smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR,
873 BMCR_LOOPBACK | BMCR_FULLDPLX);
875 /* Enable MAC tx/rx, FD */
876 spin_lock_irqsave(&pdata->mac_lock, flags);
877 smsc911x_mac_write(pdata, MAC_CR, MAC_CR_FDPX_
878 | MAC_CR_TXEN_ | MAC_CR_RXEN_);
879 spin_unlock_irqrestore(&pdata->mac_lock, flags);
881 if (smsc911x_phy_check_loopbackpkt(pdata) == 0) {
888 spin_lock_irqsave(&pdata->mac_lock, flags);
889 smsc911x_mac_write(pdata, MAC_CR, 0);
890 spin_unlock_irqrestore(&pdata->mac_lock, flags);
892 smsc911x_phy_reset(pdata);
896 spin_lock_irqsave(&pdata->mac_lock, flags);
897 smsc911x_mac_write(pdata, MAC_CR, 0);
898 spin_unlock_irqrestore(&pdata->mac_lock, flags);
900 /* Cancel PHY loopback mode */
901 smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, 0);
903 smsc911x_reg_write(pdata, TX_CFG, 0);
904 smsc911x_reg_write(pdata, RX_CFG, 0);
908 #endif /* USE_PHY_WORK_AROUND */
910 static void smsc911x_phy_update_flowcontrol(struct smsc911x_data *pdata)
912 struct phy_device *phy_dev = pdata->phy_dev;
913 u32 afc = smsc911x_reg_read(pdata, AFC_CFG);
917 if (phy_dev->duplex == DUPLEX_FULL) {
918 u16 lcladv = phy_read(phy_dev, MII_ADVERTISE);
919 u16 rmtadv = phy_read(phy_dev, MII_LPA);
920 u8 cap = mii_resolve_flowctrl_fdx(lcladv, rmtadv);
922 if (cap & FLOW_CTRL_RX)
927 if (cap & FLOW_CTRL_TX)
932 SMSC_TRACE(pdata, hw, "rx pause %s, tx pause %s",
933 (cap & FLOW_CTRL_RX ? "enabled" : "disabled"),
934 (cap & FLOW_CTRL_TX ? "enabled" : "disabled"));
936 SMSC_TRACE(pdata, hw, "half duplex");
941 spin_lock_irqsave(&pdata->mac_lock, flags);
942 smsc911x_mac_write(pdata, FLOW, flow);
943 spin_unlock_irqrestore(&pdata->mac_lock, flags);
945 smsc911x_reg_write(pdata, AFC_CFG, afc);
948 /* Update link mode if anything has changed. Called periodically when the
949 * PHY is in polling mode, even if nothing has changed. */
950 static void smsc911x_phy_adjust_link(struct net_device *dev)
952 struct smsc911x_data *pdata = netdev_priv(dev);
953 struct phy_device *phy_dev = pdata->phy_dev;
957 if (phy_dev->duplex != pdata->last_duplex) {
959 SMSC_TRACE(pdata, hw, "duplex state has changed");
961 spin_lock_irqsave(&pdata->mac_lock, flags);
962 mac_cr = smsc911x_mac_read(pdata, MAC_CR);
963 if (phy_dev->duplex) {
964 SMSC_TRACE(pdata, hw,
965 "configuring for full duplex mode");
966 mac_cr |= MAC_CR_FDPX_;
968 SMSC_TRACE(pdata, hw,
969 "configuring for half duplex mode");
970 mac_cr &= ~MAC_CR_FDPX_;
972 smsc911x_mac_write(pdata, MAC_CR, mac_cr);
973 spin_unlock_irqrestore(&pdata->mac_lock, flags);
975 smsc911x_phy_update_flowcontrol(pdata);
976 pdata->last_duplex = phy_dev->duplex;
979 carrier = netif_carrier_ok(dev);
980 if (carrier != pdata->last_carrier) {
981 SMSC_TRACE(pdata, hw, "carrier state has changed");
983 SMSC_TRACE(pdata, hw, "configuring for carrier OK");
984 if ((pdata->gpio_orig_setting & GPIO_CFG_LED1_EN_) &&
985 (!pdata->using_extphy)) {
986 /* Restore original GPIO configuration */
987 pdata->gpio_setting = pdata->gpio_orig_setting;
988 smsc911x_reg_write(pdata, GPIO_CFG,
989 pdata->gpio_setting);
992 SMSC_TRACE(pdata, hw, "configuring for no carrier");
993 /* Check global setting that LED1
994 * usage is 10/100 indicator */
995 pdata->gpio_setting = smsc911x_reg_read(pdata,
997 if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_) &&
998 (!pdata->using_extphy)) {
999 /* Force 10/100 LED off, after saving
1000 * original GPIO configuration */
1001 pdata->gpio_orig_setting = pdata->gpio_setting;
1003 pdata->gpio_setting &= ~GPIO_CFG_LED1_EN_;
1004 pdata->gpio_setting |= (GPIO_CFG_GPIOBUF0_
1005 | GPIO_CFG_GPIODIR0_
1006 | GPIO_CFG_GPIOD0_);
1007 smsc911x_reg_write(pdata, GPIO_CFG,
1008 pdata->gpio_setting);
1011 pdata->last_carrier = carrier;
1015 static int smsc911x_mii_probe(struct net_device *dev)
1017 struct smsc911x_data *pdata = netdev_priv(dev);
1018 struct phy_device *phydev = NULL;
1021 /* find the first phy */
1022 phydev = phy_find_first(pdata->mii_bus);
1024 netdev_err(dev, "no PHY found\n");
1028 SMSC_TRACE(pdata, probe, "PHY: addr %d, phy_id 0x%08X",
1029 phydev->addr, phydev->phy_id);
1031 ret = phy_connect_direct(dev, phydev, &smsc911x_phy_adjust_link,
1032 pdata->config.phy_interface);
1035 netdev_err(dev, "Could not attach to PHY\n");
1040 "attached PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n",
1041 phydev->drv->name, dev_name(&phydev->dev), phydev->irq);
1043 /* mask with MAC supported features */
1044 phydev->supported &= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
1045 SUPPORTED_Asym_Pause);
1046 phydev->advertising = phydev->supported;
1048 pdata->phy_dev = phydev;
1049 pdata->last_duplex = -1;
1050 pdata->last_carrier = -1;
1052 #ifdef USE_PHY_WORK_AROUND
1053 if (smsc911x_phy_loopbacktest(dev) < 0) {
1054 SMSC_WARN(pdata, hw, "Failed Loop Back Test");
1055 phy_disconnect(phydev);
1058 SMSC_TRACE(pdata, hw, "Passed Loop Back Test");
1059 #endif /* USE_PHY_WORK_AROUND */
1061 SMSC_TRACE(pdata, hw, "phy initialised successfully");
1065 static int smsc911x_mii_init(struct platform_device *pdev,
1066 struct net_device *dev)
1068 struct smsc911x_data *pdata = netdev_priv(dev);
1069 int err = -ENXIO, i;
1071 pdata->mii_bus = mdiobus_alloc();
1072 if (!pdata->mii_bus) {
1077 pdata->mii_bus->name = SMSC_MDIONAME;
1078 snprintf(pdata->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x",
1079 pdev->name, pdev->id);
1080 pdata->mii_bus->priv = pdata;
1081 pdata->mii_bus->read = smsc911x_mii_read;
1082 pdata->mii_bus->write = smsc911x_mii_write;
1083 pdata->mii_bus->irq = pdata->phy_irq;
1084 for (i = 0; i < PHY_MAX_ADDR; ++i)
1085 pdata->mii_bus->irq[i] = PHY_POLL;
1087 pdata->mii_bus->parent = &pdev->dev;
1089 switch (pdata->idrev & 0xFFFF0000) {
1094 /* External PHY supported, try to autodetect */
1095 smsc911x_phy_initialise_external(pdata);
1098 SMSC_TRACE(pdata, hw, "External PHY is not supported, "
1099 "using internal PHY");
1100 pdata->using_extphy = 0;
1104 if (!pdata->using_extphy) {
1105 /* Mask all PHYs except ID 1 (internal) */
1106 pdata->mii_bus->phy_mask = ~(1 << 1);
1109 if (mdiobus_register(pdata->mii_bus)) {
1110 SMSC_WARN(pdata, probe, "Error registering mii bus");
1111 goto err_out_free_bus_2;
1114 if (smsc911x_mii_probe(dev) < 0) {
1115 SMSC_WARN(pdata, probe, "Error registering mii bus");
1116 goto err_out_unregister_bus_3;
1121 err_out_unregister_bus_3:
1122 mdiobus_unregister(pdata->mii_bus);
1124 mdiobus_free(pdata->mii_bus);
1129 /* Gets the number of tx statuses in the fifo */
1130 static unsigned int smsc911x_tx_get_txstatcount(struct smsc911x_data *pdata)
1132 return (smsc911x_reg_read(pdata, TX_FIFO_INF)
1133 & TX_FIFO_INF_TSUSED_) >> 16;
1136 /* Reads tx statuses and increments counters where necessary */
1137 static void smsc911x_tx_update_txcounters(struct net_device *dev)
1139 struct smsc911x_data *pdata = netdev_priv(dev);
1140 unsigned int tx_stat;
1142 while ((tx_stat = smsc911x_tx_get_txstatus(pdata)) != 0) {
1143 if (unlikely(tx_stat & 0x80000000)) {
1144 /* In this driver the packet tag is used as the packet
1145 * length. Since a packet length can never reach the
1146 * size of 0x8000, this bit is reserved. It is worth
1147 * noting that the "reserved bit" in the warning above
1148 * does not reference a hardware defined reserved bit
1149 * but rather a driver defined one.
1151 SMSC_WARN(pdata, hw, "Packet tag reserved bit is high");
1153 if (unlikely(tx_stat & TX_STS_ES_)) {
1154 dev->stats.tx_errors++;
1156 dev->stats.tx_packets++;
1157 dev->stats.tx_bytes += (tx_stat >> 16);
1159 if (unlikely(tx_stat & TX_STS_EXCESS_COL_)) {
1160 dev->stats.collisions += 16;
1161 dev->stats.tx_aborted_errors += 1;
1163 dev->stats.collisions +=
1164 ((tx_stat >> 3) & 0xF);
1166 if (unlikely(tx_stat & TX_STS_LOST_CARRIER_))
1167 dev->stats.tx_carrier_errors += 1;
1168 if (unlikely(tx_stat & TX_STS_LATE_COL_)) {
1169 dev->stats.collisions++;
1170 dev->stats.tx_aborted_errors++;
1176 /* Increments the Rx error counters */
1178 smsc911x_rx_counterrors(struct net_device *dev, unsigned int rxstat)
1182 if (unlikely(rxstat & RX_STS_ES_)) {
1183 dev->stats.rx_errors++;
1184 if (unlikely(rxstat & RX_STS_CRC_ERR_)) {
1185 dev->stats.rx_crc_errors++;
1189 if (likely(!crc_err)) {
1190 if (unlikely((rxstat & RX_STS_FRAME_TYPE_) &&
1191 (rxstat & RX_STS_LENGTH_ERR_)))
1192 dev->stats.rx_length_errors++;
1193 if (rxstat & RX_STS_MCAST_)
1194 dev->stats.multicast++;
1198 /* Quickly dumps bad packets */
1200 smsc911x_rx_fastforward(struct smsc911x_data *pdata, unsigned int pktwords)
1202 if (likely(pktwords >= 4)) {
1203 unsigned int timeout = 500;
1205 smsc911x_reg_write(pdata, RX_DP_CTRL, RX_DP_CTRL_RX_FFWD_);
1208 val = smsc911x_reg_read(pdata, RX_DP_CTRL);
1209 } while ((val & RX_DP_CTRL_RX_FFWD_) && --timeout);
1211 if (unlikely(timeout == 0))
1212 SMSC_WARN(pdata, hw, "Timed out waiting for "
1213 "RX FFWD to finish, RX_DP_CTRL: 0x%08X", val);
1217 temp = smsc911x_reg_read(pdata, RX_DATA_FIFO);
1221 /* NAPI poll function */
1222 static int smsc911x_poll(struct napi_struct *napi, int budget)
1224 struct smsc911x_data *pdata =
1225 container_of(napi, struct smsc911x_data, napi);
1226 struct net_device *dev = pdata->dev;
1229 while (npackets < budget) {
1230 unsigned int pktlength;
1231 unsigned int pktwords;
1232 struct sk_buff *skb;
1233 unsigned int rxstat = smsc911x_rx_get_rxstatus(pdata);
1237 /* We processed all packets available. Tell NAPI it can
1238 * stop polling then re-enable rx interrupts */
1239 smsc911x_reg_write(pdata, INT_STS, INT_STS_RSFL_);
1240 napi_complete(napi);
1241 temp = smsc911x_reg_read(pdata, INT_EN);
1242 temp |= INT_EN_RSFL_EN_;
1243 smsc911x_reg_write(pdata, INT_EN, temp);
1247 /* Count packet for NAPI scheduling, even if it has an error.
1248 * Error packets still require cycles to discard */
1251 pktlength = ((rxstat & 0x3FFF0000) >> 16);
1252 pktwords = (pktlength + NET_IP_ALIGN + 3) >> 2;
1253 smsc911x_rx_counterrors(dev, rxstat);
1255 if (unlikely(rxstat & RX_STS_ES_)) {
1256 SMSC_WARN(pdata, rx_err,
1257 "Discarding packet with error bit set");
1258 /* Packet has an error, discard it and continue with
1260 smsc911x_rx_fastforward(pdata, pktwords);
1261 dev->stats.rx_dropped++;
1265 skb = netdev_alloc_skb(dev, pktwords << 2);
1266 if (unlikely(!skb)) {
1267 SMSC_WARN(pdata, rx_err,
1268 "Unable to allocate skb for rx packet");
1269 /* Drop the packet and stop this polling iteration */
1270 smsc911x_rx_fastforward(pdata, pktwords);
1271 dev->stats.rx_dropped++;
1275 pdata->ops->rx_readfifo(pdata,
1276 (unsigned int *)skb->data, pktwords);
1278 /* Align IP on 16B boundary */
1279 skb_reserve(skb, NET_IP_ALIGN);
1280 skb_put(skb, pktlength - 4);
1281 skb->protocol = eth_type_trans(skb, dev);
1282 skb_checksum_none_assert(skb);
1283 netif_receive_skb(skb);
1285 /* Update counters */
1286 dev->stats.rx_packets++;
1287 dev->stats.rx_bytes += (pktlength - 4);
1290 /* Return total received packets */
1294 /* Returns hash bit number for given MAC address
1296 * 01 00 5E 00 00 01 -> returns bit number 31 */
1297 static unsigned int smsc911x_hash(char addr[ETH_ALEN])
1299 return (ether_crc(ETH_ALEN, addr) >> 26) & 0x3f;
1302 static void smsc911x_rx_multicast_update(struct smsc911x_data *pdata)
1304 /* Performs the multicast & mac_cr update. This is called when
1305 * safe on the current hardware, and with the mac_lock held */
1306 unsigned int mac_cr;
1308 SMSC_ASSERT_MAC_LOCK(pdata);
1310 mac_cr = smsc911x_mac_read(pdata, MAC_CR);
1311 mac_cr |= pdata->set_bits_mask;
1312 mac_cr &= ~(pdata->clear_bits_mask);
1313 smsc911x_mac_write(pdata, MAC_CR, mac_cr);
1314 smsc911x_mac_write(pdata, HASHH, pdata->hashhi);
1315 smsc911x_mac_write(pdata, HASHL, pdata->hashlo);
1316 SMSC_TRACE(pdata, hw, "maccr 0x%08X, HASHH 0x%08X, HASHL 0x%08X",
1317 mac_cr, pdata->hashhi, pdata->hashlo);
1320 static void smsc911x_rx_multicast_update_workaround(struct smsc911x_data *pdata)
1322 unsigned int mac_cr;
1324 /* This function is only called for older LAN911x devices
1325 * (revA or revB), where MAC_CR, HASHH and HASHL should not
1326 * be modified during Rx - newer devices immediately update the
1329 * This is called from interrupt context */
1331 spin_lock(&pdata->mac_lock);
1333 /* Check Rx has stopped */
1334 if (smsc911x_mac_read(pdata, MAC_CR) & MAC_CR_RXEN_)
1335 SMSC_WARN(pdata, drv, "Rx not stopped");
1337 /* Perform the update - safe to do now Rx has stopped */
1338 smsc911x_rx_multicast_update(pdata);
1341 mac_cr = smsc911x_mac_read(pdata, MAC_CR);
1342 mac_cr |= MAC_CR_RXEN_;
1343 smsc911x_mac_write(pdata, MAC_CR, mac_cr);
1345 pdata->multicast_update_pending = 0;
1347 spin_unlock(&pdata->mac_lock);
1350 static int smsc911x_phy_general_power_up(struct smsc911x_data *pdata)
1354 if (!pdata->phy_dev)
1357 /* If the internal PHY is in General Power-Down mode, all, except the
1358 * management interface, is powered-down and stays in that condition as
1359 * long as Phy register bit 0.11 is HIGH.
1361 * In that case, clear the bit 0.11, so the PHY powers up and we can
1362 * access to the phy registers.
1364 rc = phy_read(pdata->phy_dev, MII_BMCR);
1366 SMSC_WARN(pdata, drv, "Failed reading PHY control reg");
1370 /* If the PHY general power-down bit is not set is not necessary to
1371 * disable the general power down-mode.
1373 if (rc & BMCR_PDOWN) {
1374 rc = phy_write(pdata->phy_dev, MII_BMCR, rc & ~BMCR_PDOWN);
1376 SMSC_WARN(pdata, drv, "Failed writing PHY control reg");
1380 usleep_range(1000, 1500);
1386 static int smsc911x_phy_disable_energy_detect(struct smsc911x_data *pdata)
1390 if (!pdata->phy_dev)
1393 rc = phy_read(pdata->phy_dev, MII_LAN83C185_CTRL_STATUS);
1396 SMSC_WARN(pdata, drv, "Failed reading PHY control reg");
1400 /* Only disable if energy detect mode is already enabled */
1401 if (rc & MII_LAN83C185_EDPWRDOWN) {
1402 /* Disable energy detect mode for this SMSC Transceivers */
1403 rc = phy_write(pdata->phy_dev, MII_LAN83C185_CTRL_STATUS,
1404 rc & (~MII_LAN83C185_EDPWRDOWN));
1407 SMSC_WARN(pdata, drv, "Failed writing PHY control reg");
1410 /* Allow PHY to wakeup */
1417 static int smsc911x_phy_enable_energy_detect(struct smsc911x_data *pdata)
1421 if (!pdata->phy_dev)
1424 rc = phy_read(pdata->phy_dev, MII_LAN83C185_CTRL_STATUS);
1427 SMSC_WARN(pdata, drv, "Failed reading PHY control reg");
1431 /* Only enable if energy detect mode is already disabled */
1432 if (!(rc & MII_LAN83C185_EDPWRDOWN)) {
1433 /* Enable energy detect mode for this SMSC Transceivers */
1434 rc = phy_write(pdata->phy_dev, MII_LAN83C185_CTRL_STATUS,
1435 rc | MII_LAN83C185_EDPWRDOWN);
1438 SMSC_WARN(pdata, drv, "Failed writing PHY control reg");
1445 static int smsc911x_soft_reset(struct smsc911x_data *pdata)
1447 unsigned int timeout;
1452 * Make sure to power-up the PHY chip before doing a reset, otherwise
1455 ret = smsc911x_phy_general_power_up(pdata);
1457 SMSC_WARN(pdata, drv, "Failed to power-up the PHY chip");
1462 * LAN9210/LAN9211/LAN9220/LAN9221 chips have an internal PHY that
1463 * are initialized in a Energy Detect Power-Down mode that prevents
1464 * the MAC chip to be software reseted. So we have to wakeup the PHY
1467 if (pdata->generation == 4) {
1468 ret = smsc911x_phy_disable_energy_detect(pdata);
1471 SMSC_WARN(pdata, drv, "Failed to wakeup the PHY chip");
1476 /* Reset the LAN911x */
1477 smsc911x_reg_write(pdata, HW_CFG, HW_CFG_SRST_);
1481 temp = smsc911x_reg_read(pdata, HW_CFG);
1482 } while ((--timeout) && (temp & HW_CFG_SRST_));
1484 if (unlikely(temp & HW_CFG_SRST_)) {
1485 SMSC_WARN(pdata, drv, "Failed to complete reset");
1489 if (pdata->generation == 4) {
1490 ret = smsc911x_phy_enable_energy_detect(pdata);
1493 SMSC_WARN(pdata, drv, "Failed to wakeup the PHY chip");
1501 /* Sets the device MAC address to dev_addr, called with mac_lock held */
1503 smsc911x_set_hw_mac_address(struct smsc911x_data *pdata, u8 dev_addr[6])
1505 u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4];
1506 u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) |
1507 (dev_addr[1] << 8) | dev_addr[0];
1509 SMSC_ASSERT_MAC_LOCK(pdata);
1511 smsc911x_mac_write(pdata, ADDRH, mac_high16);
1512 smsc911x_mac_write(pdata, ADDRL, mac_low32);
1515 static void smsc911x_disable_irq_chip(struct net_device *dev)
1517 struct smsc911x_data *pdata = netdev_priv(dev);
1519 smsc911x_reg_write(pdata, INT_EN, 0);
1520 smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF);
1523 static int smsc911x_open(struct net_device *dev)
1525 struct smsc911x_data *pdata = netdev_priv(dev);
1526 unsigned int timeout;
1528 unsigned int intcfg;
1530 /* if the phy is not yet registered, retry later*/
1531 if (!pdata->phy_dev) {
1532 SMSC_WARN(pdata, hw, "phy_dev is NULL");
1536 /* Reset the LAN911x */
1537 if (smsc911x_soft_reset(pdata)) {
1538 SMSC_WARN(pdata, hw, "soft reset failed");
1542 smsc911x_reg_write(pdata, HW_CFG, 0x00050000);
1543 smsc911x_reg_write(pdata, AFC_CFG, 0x006E3740);
1545 /* Increase the legal frame size of VLAN tagged frames to 1522 bytes */
1546 spin_lock_irq(&pdata->mac_lock);
1547 smsc911x_mac_write(pdata, VLAN1, ETH_P_8021Q);
1548 spin_unlock_irq(&pdata->mac_lock);
1550 /* Make sure EEPROM has finished loading before setting GPIO_CFG */
1552 while ((smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) &&
1557 if (unlikely(timeout == 0))
1558 SMSC_WARN(pdata, ifup,
1559 "Timed out waiting for EEPROM busy bit to clear");
1561 smsc911x_reg_write(pdata, GPIO_CFG, 0x70070000);
1563 /* The soft reset above cleared the device's MAC address,
1564 * restore it from local copy (set in probe) */
1565 spin_lock_irq(&pdata->mac_lock);
1566 smsc911x_set_hw_mac_address(pdata, dev->dev_addr);
1567 spin_unlock_irq(&pdata->mac_lock);
1569 /* Initialise irqs, but leave all sources disabled */
1570 smsc911x_disable_irq_chip(dev);
1572 /* Set interrupt deassertion to 100uS */
1573 intcfg = ((10 << 24) | INT_CFG_IRQ_EN_);
1575 if (pdata->config.irq_polarity) {
1576 SMSC_TRACE(pdata, ifup, "irq polarity: active high");
1577 intcfg |= INT_CFG_IRQ_POL_;
1579 SMSC_TRACE(pdata, ifup, "irq polarity: active low");
1582 if (pdata->config.irq_type) {
1583 SMSC_TRACE(pdata, ifup, "irq type: push-pull");
1584 intcfg |= INT_CFG_IRQ_TYPE_;
1586 SMSC_TRACE(pdata, ifup, "irq type: open drain");
1589 smsc911x_reg_write(pdata, INT_CFG, intcfg);
1591 SMSC_TRACE(pdata, ifup, "Testing irq handler using IRQ %d", dev->irq);
1592 pdata->software_irq_signal = 0;
1595 temp = smsc911x_reg_read(pdata, INT_EN);
1596 temp |= INT_EN_SW_INT_EN_;
1597 smsc911x_reg_write(pdata, INT_EN, temp);
1601 if (pdata->software_irq_signal)
1606 if (!pdata->software_irq_signal) {
1607 netdev_warn(dev, "ISR failed signaling test (IRQ %d)\n",
1611 SMSC_TRACE(pdata, ifup, "IRQ handler passed test using IRQ %d",
1614 netdev_info(dev, "SMSC911x/921x identified at %#08lx, IRQ: %d\n",
1615 (unsigned long)pdata->ioaddr, dev->irq);
1617 /* Reset the last known duplex and carrier */
1618 pdata->last_duplex = -1;
1619 pdata->last_carrier = -1;
1621 /* Bring the PHY up */
1622 phy_start(pdata->phy_dev);
1624 temp = smsc911x_reg_read(pdata, HW_CFG);
1625 /* Preserve TX FIFO size and external PHY configuration */
1626 temp &= (HW_CFG_TX_FIF_SZ_|0x00000FFF);
1628 smsc911x_reg_write(pdata, HW_CFG, temp);
1630 temp = smsc911x_reg_read(pdata, FIFO_INT);
1631 temp |= FIFO_INT_TX_AVAIL_LEVEL_;
1632 temp &= ~(FIFO_INT_RX_STS_LEVEL_);
1633 smsc911x_reg_write(pdata, FIFO_INT, temp);
1635 /* set RX Data offset to 2 bytes for alignment */
1636 smsc911x_reg_write(pdata, RX_CFG, (NET_IP_ALIGN << 8));
1638 /* enable NAPI polling before enabling RX interrupts */
1639 napi_enable(&pdata->napi);
1641 temp = smsc911x_reg_read(pdata, INT_EN);
1642 temp |= (INT_EN_TDFA_EN_ | INT_EN_RSFL_EN_ | INT_EN_RXSTOP_INT_EN_);
1643 smsc911x_reg_write(pdata, INT_EN, temp);
1645 spin_lock_irq(&pdata->mac_lock);
1646 temp = smsc911x_mac_read(pdata, MAC_CR);
1647 temp |= (MAC_CR_TXEN_ | MAC_CR_RXEN_ | MAC_CR_HBDIS_);
1648 smsc911x_mac_write(pdata, MAC_CR, temp);
1649 spin_unlock_irq(&pdata->mac_lock);
1651 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_);
1653 netif_start_queue(dev);
1657 /* Entry point for stopping the interface */
1658 static int smsc911x_stop(struct net_device *dev)
1660 struct smsc911x_data *pdata = netdev_priv(dev);
1663 /* Disable all device interrupts */
1664 temp = smsc911x_reg_read(pdata, INT_CFG);
1665 temp &= ~INT_CFG_IRQ_EN_;
1666 smsc911x_reg_write(pdata, INT_CFG, temp);
1668 /* Stop Tx and Rx polling */
1669 netif_stop_queue(dev);
1670 napi_disable(&pdata->napi);
1672 /* At this point all Rx and Tx activity is stopped */
1673 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP);
1674 smsc911x_tx_update_txcounters(dev);
1676 /* Bring the PHY down */
1678 phy_stop(pdata->phy_dev);
1680 SMSC_TRACE(pdata, ifdown, "Interface stopped");
1684 /* Entry point for transmitting a packet */
1685 static int smsc911x_hard_start_xmit(struct sk_buff *skb, struct net_device *dev)
1687 struct smsc911x_data *pdata = netdev_priv(dev);
1688 unsigned int freespace;
1689 unsigned int tx_cmd_a;
1690 unsigned int tx_cmd_b;
1695 freespace = smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TDFREE_;
1697 if (unlikely(freespace < TX_FIFO_LOW_THRESHOLD))
1698 SMSC_WARN(pdata, tx_err,
1699 "Tx data fifo low, space available: %d", freespace);
1701 /* Word alignment adjustment */
1702 tx_cmd_a = (u32)((ulong)skb->data & 0x03) << 16;
1703 tx_cmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_;
1704 tx_cmd_a |= (unsigned int)skb->len;
1706 tx_cmd_b = ((unsigned int)skb->len) << 16;
1707 tx_cmd_b |= (unsigned int)skb->len;
1709 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_a);
1710 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_b);
1712 bufp = (ulong)skb->data & (~0x3);
1713 wrsz = (u32)skb->len + 3;
1714 wrsz += (u32)((ulong)skb->data & 0x3);
1717 pdata->ops->tx_writefifo(pdata, (unsigned int *)bufp, wrsz);
1718 freespace -= (skb->len + 32);
1719 skb_tx_timestamp(skb);
1720 dev_consume_skb_any(skb);
1722 if (unlikely(smsc911x_tx_get_txstatcount(pdata) >= 30))
1723 smsc911x_tx_update_txcounters(dev);
1725 if (freespace < TX_FIFO_LOW_THRESHOLD) {
1726 netif_stop_queue(dev);
1727 temp = smsc911x_reg_read(pdata, FIFO_INT);
1730 smsc911x_reg_write(pdata, FIFO_INT, temp);
1733 return NETDEV_TX_OK;
1736 /* Entry point for getting status counters */
1737 static struct net_device_stats *smsc911x_get_stats(struct net_device *dev)
1739 struct smsc911x_data *pdata = netdev_priv(dev);
1740 smsc911x_tx_update_txcounters(dev);
1741 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP);
1745 /* Entry point for setting addressing modes */
1746 static void smsc911x_set_multicast_list(struct net_device *dev)
1748 struct smsc911x_data *pdata = netdev_priv(dev);
1749 unsigned long flags;
1751 if (dev->flags & IFF_PROMISC) {
1752 /* Enabling promiscuous mode */
1753 pdata->set_bits_mask = MAC_CR_PRMS_;
1754 pdata->clear_bits_mask = (MAC_CR_MCPAS_ | MAC_CR_HPFILT_);
1757 } else if (dev->flags & IFF_ALLMULTI) {
1758 /* Enabling all multicast mode */
1759 pdata->set_bits_mask = MAC_CR_MCPAS_;
1760 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_HPFILT_);
1763 } else if (!netdev_mc_empty(dev)) {
1764 /* Enabling specific multicast addresses */
1765 unsigned int hash_high = 0;
1766 unsigned int hash_low = 0;
1767 struct netdev_hw_addr *ha;
1769 pdata->set_bits_mask = MAC_CR_HPFILT_;
1770 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_MCPAS_);
1772 netdev_for_each_mc_addr(ha, dev) {
1773 unsigned int bitnum = smsc911x_hash(ha->addr);
1774 unsigned int mask = 0x01 << (bitnum & 0x1F);
1782 pdata->hashhi = hash_high;
1783 pdata->hashlo = hash_low;
1785 /* Enabling local MAC address only */
1786 pdata->set_bits_mask = 0;
1787 pdata->clear_bits_mask =
1788 (MAC_CR_PRMS_ | MAC_CR_MCPAS_ | MAC_CR_HPFILT_);
1793 spin_lock_irqsave(&pdata->mac_lock, flags);
1795 if (pdata->generation <= 1) {
1796 /* Older hardware revision - cannot change these flags while
1798 if (!pdata->multicast_update_pending) {
1800 SMSC_TRACE(pdata, hw, "scheduling mcast update");
1801 pdata->multicast_update_pending = 1;
1803 /* Request the hardware to stop, then perform the
1804 * update when we get an RX_STOP interrupt */
1805 temp = smsc911x_mac_read(pdata, MAC_CR);
1806 temp &= ~(MAC_CR_RXEN_);
1807 smsc911x_mac_write(pdata, MAC_CR, temp);
1809 /* There is another update pending, this should now
1810 * use the newer values */
1813 /* Newer hardware revision - can write immediately */
1814 smsc911x_rx_multicast_update(pdata);
1817 spin_unlock_irqrestore(&pdata->mac_lock, flags);
1820 static irqreturn_t smsc911x_irqhandler(int irq, void *dev_id)
1822 struct net_device *dev = dev_id;
1823 struct smsc911x_data *pdata = netdev_priv(dev);
1824 u32 intsts = smsc911x_reg_read(pdata, INT_STS);
1825 u32 inten = smsc911x_reg_read(pdata, INT_EN);
1826 int serviced = IRQ_NONE;
1829 if (unlikely(intsts & inten & INT_STS_SW_INT_)) {
1830 temp = smsc911x_reg_read(pdata, INT_EN);
1831 temp &= (~INT_EN_SW_INT_EN_);
1832 smsc911x_reg_write(pdata, INT_EN, temp);
1833 smsc911x_reg_write(pdata, INT_STS, INT_STS_SW_INT_);
1834 pdata->software_irq_signal = 1;
1836 serviced = IRQ_HANDLED;
1839 if (unlikely(intsts & inten & INT_STS_RXSTOP_INT_)) {
1840 /* Called when there is a multicast update scheduled and
1841 * it is now safe to complete the update */
1842 SMSC_TRACE(pdata, intr, "RX Stop interrupt");
1843 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_);
1844 if (pdata->multicast_update_pending)
1845 smsc911x_rx_multicast_update_workaround(pdata);
1846 serviced = IRQ_HANDLED;
1849 if (intsts & inten & INT_STS_TDFA_) {
1850 temp = smsc911x_reg_read(pdata, FIFO_INT);
1851 temp |= FIFO_INT_TX_AVAIL_LEVEL_;
1852 smsc911x_reg_write(pdata, FIFO_INT, temp);
1853 smsc911x_reg_write(pdata, INT_STS, INT_STS_TDFA_);
1854 netif_wake_queue(dev);
1855 serviced = IRQ_HANDLED;
1858 if (unlikely(intsts & inten & INT_STS_RXE_)) {
1859 SMSC_TRACE(pdata, intr, "RX Error interrupt");
1860 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXE_);
1861 serviced = IRQ_HANDLED;
1864 if (likely(intsts & inten & INT_STS_RSFL_)) {
1865 if (likely(napi_schedule_prep(&pdata->napi))) {
1866 /* Disable Rx interrupts */
1867 temp = smsc911x_reg_read(pdata, INT_EN);
1868 temp &= (~INT_EN_RSFL_EN_);
1869 smsc911x_reg_write(pdata, INT_EN, temp);
1870 /* Schedule a NAPI poll */
1871 __napi_schedule(&pdata->napi);
1873 SMSC_WARN(pdata, rx_err, "napi_schedule_prep failed");
1875 serviced = IRQ_HANDLED;
1881 #ifdef CONFIG_NET_POLL_CONTROLLER
1882 static void smsc911x_poll_controller(struct net_device *dev)
1884 disable_irq(dev->irq);
1885 smsc911x_irqhandler(0, dev);
1886 enable_irq(dev->irq);
1888 #endif /* CONFIG_NET_POLL_CONTROLLER */
1890 static int smsc911x_set_mac_address(struct net_device *dev, void *p)
1892 struct smsc911x_data *pdata = netdev_priv(dev);
1893 struct sockaddr *addr = p;
1895 /* On older hardware revisions we cannot change the mac address
1896 * registers while receiving data. Newer devices can safely change
1897 * this at any time. */
1898 if (pdata->generation <= 1 && netif_running(dev))
1901 if (!is_valid_ether_addr(addr->sa_data))
1902 return -EADDRNOTAVAIL;
1904 memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
1906 spin_lock_irq(&pdata->mac_lock);
1907 smsc911x_set_hw_mac_address(pdata, dev->dev_addr);
1908 spin_unlock_irq(&pdata->mac_lock);
1910 netdev_info(dev, "MAC Address: %pM\n", dev->dev_addr);
1915 /* Standard ioctls for mii-tool */
1916 static int smsc911x_do_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1918 struct smsc911x_data *pdata = netdev_priv(dev);
1920 if (!netif_running(dev) || !pdata->phy_dev)
1923 return phy_mii_ioctl(pdata->phy_dev, ifr, cmd);
1927 smsc911x_ethtool_getsettings(struct net_device *dev, struct ethtool_cmd *cmd)
1929 struct smsc911x_data *pdata = netdev_priv(dev);
1933 return phy_ethtool_gset(pdata->phy_dev, cmd);
1937 smsc911x_ethtool_setsettings(struct net_device *dev, struct ethtool_cmd *cmd)
1939 struct smsc911x_data *pdata = netdev_priv(dev);
1941 return phy_ethtool_sset(pdata->phy_dev, cmd);
1944 static void smsc911x_ethtool_getdrvinfo(struct net_device *dev,
1945 struct ethtool_drvinfo *info)
1947 strlcpy(info->driver, SMSC_CHIPNAME, sizeof(info->driver));
1948 strlcpy(info->version, SMSC_DRV_VERSION, sizeof(info->version));
1949 strlcpy(info->bus_info, dev_name(dev->dev.parent),
1950 sizeof(info->bus_info));
1953 static int smsc911x_ethtool_nwayreset(struct net_device *dev)
1955 struct smsc911x_data *pdata = netdev_priv(dev);
1957 return phy_start_aneg(pdata->phy_dev);
1960 static u32 smsc911x_ethtool_getmsglevel(struct net_device *dev)
1962 struct smsc911x_data *pdata = netdev_priv(dev);
1963 return pdata->msg_enable;
1966 static void smsc911x_ethtool_setmsglevel(struct net_device *dev, u32 level)
1968 struct smsc911x_data *pdata = netdev_priv(dev);
1969 pdata->msg_enable = level;
1972 static int smsc911x_ethtool_getregslen(struct net_device *dev)
1974 return (((E2P_DATA - ID_REV) / 4 + 1) + (WUCSR - MAC_CR) + 1 + 32) *
1979 smsc911x_ethtool_getregs(struct net_device *dev, struct ethtool_regs *regs,
1982 struct smsc911x_data *pdata = netdev_priv(dev);
1983 struct phy_device *phy_dev = pdata->phy_dev;
1984 unsigned long flags;
1989 regs->version = pdata->idrev;
1990 for (i = ID_REV; i <= E2P_DATA; i += (sizeof(u32)))
1991 data[j++] = smsc911x_reg_read(pdata, i);
1993 for (i = MAC_CR; i <= WUCSR; i++) {
1994 spin_lock_irqsave(&pdata->mac_lock, flags);
1995 data[j++] = smsc911x_mac_read(pdata, i);
1996 spin_unlock_irqrestore(&pdata->mac_lock, flags);
1999 for (i = 0; i <= 31; i++)
2000 data[j++] = smsc911x_mii_read(phy_dev->bus, phy_dev->addr, i);
2003 static void smsc911x_eeprom_enable_access(struct smsc911x_data *pdata)
2005 unsigned int temp = smsc911x_reg_read(pdata, GPIO_CFG);
2006 temp &= ~GPIO_CFG_EEPR_EN_;
2007 smsc911x_reg_write(pdata, GPIO_CFG, temp);
2011 static int smsc911x_eeprom_send_cmd(struct smsc911x_data *pdata, u32 op)
2016 SMSC_TRACE(pdata, drv, "op 0x%08x", op);
2017 if (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) {
2018 SMSC_WARN(pdata, drv, "Busy at start");
2022 e2cmd = op | E2P_CMD_EPC_BUSY_;
2023 smsc911x_reg_write(pdata, E2P_CMD, e2cmd);
2027 e2cmd = smsc911x_reg_read(pdata, E2P_CMD);
2028 } while ((e2cmd & E2P_CMD_EPC_BUSY_) && (--timeout));
2031 SMSC_TRACE(pdata, drv, "TIMED OUT");
2035 if (e2cmd & E2P_CMD_EPC_TIMEOUT_) {
2036 SMSC_TRACE(pdata, drv, "Error occurred during eeprom operation");
2043 static int smsc911x_eeprom_read_location(struct smsc911x_data *pdata,
2044 u8 address, u8 *data)
2046 u32 op = E2P_CMD_EPC_CMD_READ_ | address;
2049 SMSC_TRACE(pdata, drv, "address 0x%x", address);
2050 ret = smsc911x_eeprom_send_cmd(pdata, op);
2053 data[address] = smsc911x_reg_read(pdata, E2P_DATA);
2058 static int smsc911x_eeprom_write_location(struct smsc911x_data *pdata,
2059 u8 address, u8 data)
2061 u32 op = E2P_CMD_EPC_CMD_ERASE_ | address;
2065 SMSC_TRACE(pdata, drv, "address 0x%x, data 0x%x", address, data);
2066 ret = smsc911x_eeprom_send_cmd(pdata, op);
2069 op = E2P_CMD_EPC_CMD_WRITE_ | address;
2070 smsc911x_reg_write(pdata, E2P_DATA, (u32)data);
2072 /* Workaround for hardware read-after-write restriction */
2073 temp = smsc911x_reg_read(pdata, BYTE_TEST);
2075 ret = smsc911x_eeprom_send_cmd(pdata, op);
2081 static int smsc911x_ethtool_get_eeprom_len(struct net_device *dev)
2083 return SMSC911X_EEPROM_SIZE;
2086 static int smsc911x_ethtool_get_eeprom(struct net_device *dev,
2087 struct ethtool_eeprom *eeprom, u8 *data)
2089 struct smsc911x_data *pdata = netdev_priv(dev);
2090 u8 eeprom_data[SMSC911X_EEPROM_SIZE];
2094 smsc911x_eeprom_enable_access(pdata);
2096 len = min(eeprom->len, SMSC911X_EEPROM_SIZE);
2097 for (i = 0; i < len; i++) {
2098 int ret = smsc911x_eeprom_read_location(pdata, i, eeprom_data);
2105 memcpy(data, &eeprom_data[eeprom->offset], len);
2110 static int smsc911x_ethtool_set_eeprom(struct net_device *dev,
2111 struct ethtool_eeprom *eeprom, u8 *data)
2114 struct smsc911x_data *pdata = netdev_priv(dev);
2116 smsc911x_eeprom_enable_access(pdata);
2117 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWEN_);
2118 ret = smsc911x_eeprom_write_location(pdata, eeprom->offset, *data);
2119 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWDS_);
2121 /* Single byte write, according to man page */
2127 static const struct ethtool_ops smsc911x_ethtool_ops = {
2128 .get_settings = smsc911x_ethtool_getsettings,
2129 .set_settings = smsc911x_ethtool_setsettings,
2130 .get_link = ethtool_op_get_link,
2131 .get_drvinfo = smsc911x_ethtool_getdrvinfo,
2132 .nway_reset = smsc911x_ethtool_nwayreset,
2133 .get_msglevel = smsc911x_ethtool_getmsglevel,
2134 .set_msglevel = smsc911x_ethtool_setmsglevel,
2135 .get_regs_len = smsc911x_ethtool_getregslen,
2136 .get_regs = smsc911x_ethtool_getregs,
2137 .get_eeprom_len = smsc911x_ethtool_get_eeprom_len,
2138 .get_eeprom = smsc911x_ethtool_get_eeprom,
2139 .set_eeprom = smsc911x_ethtool_set_eeprom,
2140 .get_ts_info = ethtool_op_get_ts_info,
2143 static const struct net_device_ops smsc911x_netdev_ops = {
2144 .ndo_open = smsc911x_open,
2145 .ndo_stop = smsc911x_stop,
2146 .ndo_start_xmit = smsc911x_hard_start_xmit,
2147 .ndo_get_stats = smsc911x_get_stats,
2148 .ndo_set_rx_mode = smsc911x_set_multicast_list,
2149 .ndo_do_ioctl = smsc911x_do_ioctl,
2150 .ndo_change_mtu = eth_change_mtu,
2151 .ndo_validate_addr = eth_validate_addr,
2152 .ndo_set_mac_address = smsc911x_set_mac_address,
2153 #ifdef CONFIG_NET_POLL_CONTROLLER
2154 .ndo_poll_controller = smsc911x_poll_controller,
2158 /* copies the current mac address from hardware to dev->dev_addr */
2159 static void smsc911x_read_mac_address(struct net_device *dev)
2161 struct smsc911x_data *pdata = netdev_priv(dev);
2162 u32 mac_high16 = smsc911x_mac_read(pdata, ADDRH);
2163 u32 mac_low32 = smsc911x_mac_read(pdata, ADDRL);
2165 dev->dev_addr[0] = (u8)(mac_low32);
2166 dev->dev_addr[1] = (u8)(mac_low32 >> 8);
2167 dev->dev_addr[2] = (u8)(mac_low32 >> 16);
2168 dev->dev_addr[3] = (u8)(mac_low32 >> 24);
2169 dev->dev_addr[4] = (u8)(mac_high16);
2170 dev->dev_addr[5] = (u8)(mac_high16 >> 8);
2173 /* Initializing private device structures, only called from probe */
2174 static int smsc911x_init(struct net_device *dev)
2176 struct smsc911x_data *pdata = netdev_priv(dev);
2177 unsigned int byte_test, mask;
2178 unsigned int to = 100;
2180 SMSC_TRACE(pdata, probe, "Driver Parameters:");
2181 SMSC_TRACE(pdata, probe, "LAN base: 0x%08lX",
2182 (unsigned long)pdata->ioaddr);
2183 SMSC_TRACE(pdata, probe, "IRQ: %d", dev->irq);
2184 SMSC_TRACE(pdata, probe, "PHY will be autodetected.");
2186 spin_lock_init(&pdata->dev_lock);
2187 spin_lock_init(&pdata->mac_lock);
2189 if (pdata->ioaddr == NULL) {
2190 SMSC_WARN(pdata, probe, "pdata->ioaddr: 0x00000000");
2195 * poll the READY bit in PMT_CTRL. Any other access to the device is
2196 * forbidden while this bit isn't set. Try for 100ms
2198 * Note that this test is done before the WORD_SWAP register is
2199 * programmed. So in some configurations the READY bit is at 16 before
2200 * WORD_SWAP is written to. This issue is worked around by waiting
2201 * until either bit 0 or bit 16 gets set in PMT_CTRL.
2203 * SMSC has confirmed that checking bit 16 (marked as reserved in
2204 * the datasheet) is fine since these bits "will either never be set
2205 * or can only go high after READY does (so also indicate the device
2209 mask = PMT_CTRL_READY_ | swahw32(PMT_CTRL_READY_);
2210 while (!(smsc911x_reg_read(pdata, PMT_CTRL) & mask) && --to)
2214 netdev_err(dev, "Device not READY in 100ms aborting\n");
2218 /* Check byte ordering */
2219 byte_test = smsc911x_reg_read(pdata, BYTE_TEST);
2220 SMSC_TRACE(pdata, probe, "BYTE_TEST: 0x%08X", byte_test);
2221 if (byte_test == 0x43218765) {
2222 SMSC_TRACE(pdata, probe, "BYTE_TEST looks swapped, "
2223 "applying WORD_SWAP");
2224 smsc911x_reg_write(pdata, WORD_SWAP, 0xffffffff);
2226 /* 1 dummy read of BYTE_TEST is needed after a write to
2227 * WORD_SWAP before its contents are valid */
2228 byte_test = smsc911x_reg_read(pdata, BYTE_TEST);
2230 byte_test = smsc911x_reg_read(pdata, BYTE_TEST);
2233 if (byte_test != 0x87654321) {
2234 SMSC_WARN(pdata, drv, "BYTE_TEST: 0x%08X", byte_test);
2235 if (((byte_test >> 16) & 0xFFFF) == (byte_test & 0xFFFF)) {
2236 SMSC_WARN(pdata, probe,
2237 "top 16 bits equal to bottom 16 bits");
2238 SMSC_TRACE(pdata, probe,
2239 "This may mean the chip is set "
2240 "for 32 bit while the bus is reading 16 bit");
2245 /* Default generation to zero (all workarounds apply) */
2246 pdata->generation = 0;
2248 pdata->idrev = smsc911x_reg_read(pdata, ID_REV);
2249 switch (pdata->idrev & 0xFFFF0000) {
2255 /* LAN911[5678] family */
2256 pdata->generation = pdata->idrev & 0x0000FFFF;
2263 /* LAN921[5678] family */
2264 pdata->generation = 3;
2271 /* LAN9210/LAN9211/LAN9220/LAN9221 */
2272 pdata->generation = 4;
2276 SMSC_WARN(pdata, probe, "LAN911x not identified, idrev: 0x%08X",
2281 SMSC_TRACE(pdata, probe,
2282 "LAN911x identified, idrev: 0x%08X, generation: %d",
2283 pdata->idrev, pdata->generation);
2285 if (pdata->generation == 0)
2286 SMSC_WARN(pdata, probe,
2287 "This driver is not intended for this chip revision");
2289 /* workaround for platforms without an eeprom, where the mac address
2290 * is stored elsewhere and set by the bootloader. This saves the
2291 * mac address before resetting the device */
2292 if (pdata->config.flags & SMSC911X_SAVE_MAC_ADDRESS) {
2293 spin_lock_irq(&pdata->mac_lock);
2294 smsc911x_read_mac_address(dev);
2295 spin_unlock_irq(&pdata->mac_lock);
2298 /* Reset the LAN911x */
2299 if (smsc911x_soft_reset(pdata))
2302 dev->flags |= IFF_MULTICAST;
2303 netif_napi_add(dev, &pdata->napi, smsc911x_poll, SMSC_NAPI_WEIGHT);
2304 dev->netdev_ops = &smsc911x_netdev_ops;
2305 dev->ethtool_ops = &smsc911x_ethtool_ops;
2310 static int smsc911x_drv_remove(struct platform_device *pdev)
2312 struct net_device *dev;
2313 struct smsc911x_data *pdata;
2314 struct resource *res;
2316 dev = platform_get_drvdata(pdev);
2318 pdata = netdev_priv(dev);
2320 BUG_ON(!pdata->ioaddr);
2321 BUG_ON(!pdata->phy_dev);
2323 SMSC_TRACE(pdata, ifdown, "Stopping driver");
2325 phy_disconnect(pdata->phy_dev);
2326 pdata->phy_dev = NULL;
2327 mdiobus_unregister(pdata->mii_bus);
2328 mdiobus_free(pdata->mii_bus);
2330 unregister_netdev(dev);
2331 free_irq(dev->irq, dev);
2332 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
2335 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2337 release_mem_region(res->start, resource_size(res));
2339 iounmap(pdata->ioaddr);
2341 (void)smsc911x_disable_resources(pdev);
2342 smsc911x_free_resources(pdev);
2346 pm_runtime_put(&pdev->dev);
2347 pm_runtime_disable(&pdev->dev);
2352 /* standard register acces */
2353 static const struct smsc911x_ops standard_smsc911x_ops = {
2354 .reg_read = __smsc911x_reg_read,
2355 .reg_write = __smsc911x_reg_write,
2356 .rx_readfifo = smsc911x_rx_readfifo,
2357 .tx_writefifo = smsc911x_tx_writefifo,
2360 /* shifted register access */
2361 static const struct smsc911x_ops shifted_smsc911x_ops = {
2362 .reg_read = __smsc911x_reg_read_shift,
2363 .reg_write = __smsc911x_reg_write_shift,
2364 .rx_readfifo = smsc911x_rx_readfifo_shift,
2365 .tx_writefifo = smsc911x_tx_writefifo_shift,
2368 static int smsc911x_probe_config(struct smsc911x_platform_config *config,
2375 phy_interface = device_get_phy_mode(dev);
2376 if (phy_interface < 0)
2377 phy_interface = PHY_INTERFACE_MODE_NA;
2378 config->phy_interface = phy_interface;
2380 device_get_mac_address(dev, config->mac, ETH_ALEN);
2382 err = device_property_read_u32(dev, "reg-io-width", &width);
2385 if (!err && width == 4)
2386 config->flags |= SMSC911X_USE_32BIT;
2388 config->flags |= SMSC911X_USE_16BIT;
2390 device_property_read_u32(dev, "reg-shift", &config->shift);
2392 if (device_property_present(dev, "smsc,irq-active-high"))
2393 config->irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH;
2395 if (device_property_present(dev, "smsc,irq-push-pull"))
2396 config->irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL;
2398 if (device_property_present(dev, "smsc,force-internal-phy"))
2399 config->flags |= SMSC911X_FORCE_INTERNAL_PHY;
2401 if (device_property_present(dev, "smsc,force-external-phy"))
2402 config->flags |= SMSC911X_FORCE_EXTERNAL_PHY;
2404 if (device_property_present(dev, "smsc,save-mac-address"))
2405 config->flags |= SMSC911X_SAVE_MAC_ADDRESS;
2410 static int smsc911x_drv_probe(struct platform_device *pdev)
2412 struct net_device *dev;
2413 struct smsc911x_data *pdata;
2414 struct smsc911x_platform_config *config = dev_get_platdata(&pdev->dev);
2415 struct resource *res;
2416 unsigned int intcfg = 0;
2417 int res_size, irq, irq_flags;
2420 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
2423 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2425 pr_warn("Could not allocate resource\n");
2429 res_size = resource_size(res);
2431 irq = platform_get_irq(pdev, 0);
2432 if (irq == -EPROBE_DEFER) {
2433 retval = -EPROBE_DEFER;
2435 } else if (irq <= 0) {
2436 pr_warn("Could not allocate irq resource\n");
2441 if (!request_mem_region(res->start, res_size, SMSC_CHIPNAME)) {
2446 dev = alloc_etherdev(sizeof(struct smsc911x_data));
2449 goto out_release_io_1;
2452 SET_NETDEV_DEV(dev, &pdev->dev);
2454 pdata = netdev_priv(dev);
2456 irq_flags = irq_get_trigger_type(irq);
2457 pdata->ioaddr = ioremap_nocache(res->start, res_size);
2460 pdata->msg_enable = ((1 << debug) - 1);
2462 platform_set_drvdata(pdev, dev);
2464 retval = smsc911x_request_resources(pdev);
2466 goto out_request_resources_fail;
2468 retval = smsc911x_enable_resources(pdev);
2470 goto out_enable_resources_fail;
2472 if (pdata->ioaddr == NULL) {
2473 SMSC_WARN(pdata, probe, "Error smsc911x base address invalid");
2475 goto out_disable_resources;
2478 retval = smsc911x_probe_config(&pdata->config, &pdev->dev);
2479 if (retval && config) {
2480 /* copy config parameters across to pdata */
2481 memcpy(&pdata->config, config, sizeof(pdata->config));
2486 SMSC_WARN(pdata, probe, "Error smsc911x config not found");
2487 goto out_disable_resources;
2490 /* assume standard, non-shifted, access to HW registers */
2491 pdata->ops = &standard_smsc911x_ops;
2492 /* apply the right access if shifting is needed */
2493 if (pdata->config.shift)
2494 pdata->ops = &shifted_smsc911x_ops;
2496 pm_runtime_enable(&pdev->dev);
2497 pm_runtime_get_sync(&pdev->dev);
2499 retval = smsc911x_init(dev);
2501 goto out_disable_resources;
2503 /* configure irq polarity and type before connecting isr */
2504 if (pdata->config.irq_polarity == SMSC911X_IRQ_POLARITY_ACTIVE_HIGH)
2505 intcfg |= INT_CFG_IRQ_POL_;
2507 if (pdata->config.irq_type == SMSC911X_IRQ_TYPE_PUSH_PULL)
2508 intcfg |= INT_CFG_IRQ_TYPE_;
2510 smsc911x_reg_write(pdata, INT_CFG, intcfg);
2512 /* Ensure interrupts are globally disabled before connecting ISR */
2513 smsc911x_disable_irq_chip(dev);
2515 retval = request_irq(dev->irq, smsc911x_irqhandler,
2516 irq_flags | IRQF_SHARED, dev->name, dev);
2518 SMSC_WARN(pdata, probe,
2519 "Unable to claim requested irq: %d", dev->irq);
2520 goto out_disable_resources;
2523 netif_carrier_off(dev);
2525 retval = register_netdev(dev);
2527 SMSC_WARN(pdata, probe, "Error %i registering device", retval);
2530 SMSC_TRACE(pdata, probe,
2531 "Network interface: \"%s\"", dev->name);
2534 retval = smsc911x_mii_init(pdev, dev);
2536 SMSC_WARN(pdata, probe, "Error %i initialising mii", retval);
2537 goto out_unregister_netdev_5;
2540 spin_lock_irq(&pdata->mac_lock);
2542 /* Check if mac address has been specified when bringing interface up */
2543 if (is_valid_ether_addr(dev->dev_addr)) {
2544 smsc911x_set_hw_mac_address(pdata, dev->dev_addr);
2545 SMSC_TRACE(pdata, probe,
2546 "MAC Address is specified by configuration");
2547 } else if (is_valid_ether_addr(pdata->config.mac)) {
2548 memcpy(dev->dev_addr, pdata->config.mac, ETH_ALEN);
2549 SMSC_TRACE(pdata, probe,
2550 "MAC Address specified by platform data");
2552 /* Try reading mac address from device. if EEPROM is present
2553 * it will already have been set */
2556 if (is_valid_ether_addr(dev->dev_addr)) {
2557 /* eeprom values are valid so use them */
2558 SMSC_TRACE(pdata, probe,
2559 "Mac Address is read from LAN911x EEPROM");
2561 /* eeprom values are invalid, generate random MAC */
2562 eth_hw_addr_random(dev);
2563 smsc911x_set_hw_mac_address(pdata, dev->dev_addr);
2564 SMSC_TRACE(pdata, probe,
2565 "MAC Address is set to eth_random_addr");
2569 spin_unlock_irq(&pdata->mac_lock);
2571 netdev_info(dev, "MAC Address: %pM\n", dev->dev_addr);
2575 out_unregister_netdev_5:
2576 unregister_netdev(dev);
2578 free_irq(dev->irq, dev);
2579 out_disable_resources:
2580 pm_runtime_put(&pdev->dev);
2581 pm_runtime_disable(&pdev->dev);
2582 (void)smsc911x_disable_resources(pdev);
2583 out_enable_resources_fail:
2584 smsc911x_free_resources(pdev);
2585 out_request_resources_fail:
2586 iounmap(pdata->ioaddr);
2589 release_mem_region(res->start, resource_size(res));
2595 /* This implementation assumes the devices remains powered on its VDDVARIO
2596 * pins during suspend. */
2598 /* TODO: implement freeze/thaw callbacks for hibernation.*/
2600 static int smsc911x_suspend(struct device *dev)
2602 struct net_device *ndev = dev_get_drvdata(dev);
2603 struct smsc911x_data *pdata = netdev_priv(ndev);
2605 /* enable wake on LAN, energy detection and the external PME
2607 smsc911x_reg_write(pdata, PMT_CTRL,
2608 PMT_CTRL_PM_MODE_D1_ | PMT_CTRL_WOL_EN_ |
2609 PMT_CTRL_ED_EN_ | PMT_CTRL_PME_EN_);
2614 static int smsc911x_resume(struct device *dev)
2616 struct net_device *ndev = dev_get_drvdata(dev);
2617 struct smsc911x_data *pdata = netdev_priv(ndev);
2618 unsigned int to = 100;
2620 /* Note 3.11 from the datasheet:
2621 * "When the LAN9220 is in a power saving state, a write of any
2622 * data to the BYTE_TEST register will wake-up the device."
2624 smsc911x_reg_write(pdata, BYTE_TEST, 0);
2626 /* poll the READY bit in PMT_CTRL. Any other access to the device is
2627 * forbidden while this bit isn't set. Try for 100ms and return -EIO
2629 while (!(smsc911x_reg_read(pdata, PMT_CTRL) & PMT_CTRL_READY_) && --to)
2632 return (to == 0) ? -EIO : 0;
2635 static const struct dev_pm_ops smsc911x_pm_ops = {
2636 .suspend = smsc911x_suspend,
2637 .resume = smsc911x_resume,
2640 #define SMSC911X_PM_OPS (&smsc911x_pm_ops)
2643 #define SMSC911X_PM_OPS NULL
2647 static const struct of_device_id smsc911x_dt_ids[] = {
2648 { .compatible = "smsc,lan9115", },
2651 MODULE_DEVICE_TABLE(of, smsc911x_dt_ids);
2654 static const struct acpi_device_id smsc911x_acpi_match[] = {
2658 MODULE_DEVICE_TABLE(acpi, smsc911x_acpi_match);
2660 static struct platform_driver smsc911x_driver = {
2661 .probe = smsc911x_drv_probe,
2662 .remove = smsc911x_drv_remove,
2664 .name = SMSC_CHIPNAME,
2665 .pm = SMSC911X_PM_OPS,
2666 .of_match_table = of_match_ptr(smsc911x_dt_ids),
2667 .acpi_match_table = ACPI_PTR(smsc911x_acpi_match),
2671 /* Entry point for loading the module */
2672 static int __init smsc911x_init_module(void)
2675 return platform_driver_register(&smsc911x_driver);
2678 /* entry point for unloading the module */
2679 static void __exit smsc911x_cleanup_module(void)
2681 platform_driver_unregister(&smsc911x_driver);
2684 module_init(smsc911x_init_module);
2685 module_exit(smsc911x_cleanup_module);