2 * linux/drivers/mmc/host/mmci.c - ARM PrimeCell MMCI PL180/1 driver
4 * Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved.
5 * Copyright (C) 2010 ST-Ericsson SA
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License version 2 as
9 * published by the Free Software Foundation.
11 #include <linux/module.h>
12 #include <linux/moduleparam.h>
13 #include <linux/init.h>
14 #include <linux/ioport.h>
15 #include <linux/device.h>
17 #include <linux/interrupt.h>
18 #include <linux/kernel.h>
19 #include <linux/slab.h>
20 #include <linux/delay.h>
21 #include <linux/err.h>
22 #include <linux/highmem.h>
23 #include <linux/log2.h>
24 #include <linux/mmc/pm.h>
25 #include <linux/mmc/host.h>
26 #include <linux/mmc/card.h>
27 #include <linux/mmc/slot-gpio.h>
28 #include <linux/amba/bus.h>
29 #include <linux/clk.h>
30 #include <linux/scatterlist.h>
31 #include <linux/gpio.h>
32 #include <linux/of_gpio.h>
33 #include <linux/regulator/consumer.h>
34 #include <linux/dmaengine.h>
35 #include <linux/dma-mapping.h>
36 #include <linux/amba/mmci.h>
37 #include <linux/pm_runtime.h>
38 #include <linux/types.h>
39 #include <linux/pinctrl/consumer.h>
41 #include <asm/div64.h>
43 #include <asm/sizes.h>
47 #define DRIVER_NAME "mmci-pl18x"
49 static unsigned int fmax = 515633;
52 * struct variant_data - MMCI variant-specific quirks
53 * @clkreg: default value for MCICLOCK register
54 * @clkreg_enable: enable value for MMCICLOCK register
55 * @datalength_bits: number of bits in the MMCIDATALENGTH register
56 * @fifosize: number of bytes that can be written when MMCI_TXFIFOEMPTY
57 * is asserted (likewise for RX)
58 * @fifohalfsize: number of bytes that can be written when MCI_TXFIFOHALFEMPTY
59 * is asserted (likewise for RX)
60 * @sdio: variant supports SDIO
61 * @st_clkdiv: true if using a ST-specific clock divider algorithm
62 * @blksz_datactrl16: true if Block size is at b16..b30 position in datactrl register
63 * @pwrreg_powerup: power up value for MMCIPOWER register
64 * @signal_direction: input/out direction of bus signals can be indicated
65 * @pwrreg_clkgate: MMCIPOWER register must be used to gate the clock
66 * @busy_detect: true if busy detection on dat0 is supported
67 * @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply
71 unsigned int clkreg_enable;
72 unsigned int datalength_bits;
73 unsigned int fifosize;
74 unsigned int fifohalfsize;
77 bool blksz_datactrl16;
79 bool signal_direction;
85 static struct variant_data variant_arm = {
87 .fifohalfsize = 8 * 4,
88 .datalength_bits = 16,
89 .pwrreg_powerup = MCI_PWR_UP,
92 static struct variant_data variant_arm_extended_fifo = {
94 .fifohalfsize = 64 * 4,
95 .datalength_bits = 16,
96 .pwrreg_powerup = MCI_PWR_UP,
99 static struct variant_data variant_arm_extended_fifo_hwfc = {
101 .fifohalfsize = 64 * 4,
102 .clkreg_enable = MCI_ARM_HWFCEN,
103 .datalength_bits = 16,
104 .pwrreg_powerup = MCI_PWR_UP,
107 static struct variant_data variant_u300 = {
109 .fifohalfsize = 8 * 4,
110 .clkreg_enable = MCI_ST_U300_HWFCEN,
111 .datalength_bits = 16,
113 .pwrreg_powerup = MCI_PWR_ON,
114 .signal_direction = true,
115 .pwrreg_clkgate = true,
116 .pwrreg_nopower = true,
119 static struct variant_data variant_nomadik = {
121 .fifohalfsize = 8 * 4,
122 .clkreg = MCI_CLK_ENABLE,
123 .datalength_bits = 24,
126 .pwrreg_powerup = MCI_PWR_ON,
127 .signal_direction = true,
128 .pwrreg_clkgate = true,
129 .pwrreg_nopower = true,
132 static struct variant_data variant_ux500 = {
134 .fifohalfsize = 8 * 4,
135 .clkreg = MCI_CLK_ENABLE,
136 .clkreg_enable = MCI_ST_UX500_HWFCEN,
137 .datalength_bits = 24,
140 .pwrreg_powerup = MCI_PWR_ON,
141 .signal_direction = true,
142 .pwrreg_clkgate = true,
144 .pwrreg_nopower = true,
147 static struct variant_data variant_ux500v2 = {
149 .fifohalfsize = 8 * 4,
150 .clkreg = MCI_CLK_ENABLE,
151 .clkreg_enable = MCI_ST_UX500_HWFCEN,
152 .datalength_bits = 24,
155 .blksz_datactrl16 = true,
156 .pwrreg_powerup = MCI_PWR_ON,
157 .signal_direction = true,
158 .pwrreg_clkgate = true,
160 .pwrreg_nopower = true,
163 static int mmci_card_busy(struct mmc_host *mmc)
165 struct mmci_host *host = mmc_priv(mmc);
169 pm_runtime_get_sync(mmc_dev(mmc));
171 spin_lock_irqsave(&host->lock, flags);
172 if (readl(host->base + MMCISTATUS) & MCI_ST_CARDBUSY)
174 spin_unlock_irqrestore(&host->lock, flags);
176 pm_runtime_mark_last_busy(mmc_dev(mmc));
177 pm_runtime_put_autosuspend(mmc_dev(mmc));
183 * Validate mmc prerequisites
185 static int mmci_validate_data(struct mmci_host *host,
186 struct mmc_data *data)
191 if (!is_power_of_2(data->blksz)) {
192 dev_err(mmc_dev(host->mmc),
193 "unsupported block size (%d bytes)\n", data->blksz);
200 static void mmci_reg_delay(struct mmci_host *host)
203 * According to the spec, at least three feedback clock cycles
204 * of max 52 MHz must pass between two writes to the MMCICLOCK reg.
205 * Three MCLK clock cycles must pass between two MMCIPOWER reg writes.
206 * Worst delay time during card init is at 100 kHz => 30 us.
207 * Worst delay time when up and running is at 25 MHz => 120 ns.
209 if (host->cclk < 25000000)
216 * This must be called with host->lock held
218 static void mmci_write_clkreg(struct mmci_host *host, u32 clk)
220 if (host->clk_reg != clk) {
222 writel(clk, host->base + MMCICLOCK);
227 * This must be called with host->lock held
229 static void mmci_write_pwrreg(struct mmci_host *host, u32 pwr)
231 if (host->pwr_reg != pwr) {
233 writel(pwr, host->base + MMCIPOWER);
238 * This must be called with host->lock held
240 static void mmci_write_datactrlreg(struct mmci_host *host, u32 datactrl)
242 /* Keep ST Micro busy mode if enabled */
243 datactrl |= host->datactrl_reg & MCI_ST_DPSM_BUSYMODE;
245 if (host->datactrl_reg != datactrl) {
246 host->datactrl_reg = datactrl;
247 writel(datactrl, host->base + MMCIDATACTRL);
252 * This must be called with host->lock held
254 static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
256 struct variant_data *variant = host->variant;
257 u32 clk = variant->clkreg;
259 /* Make sure cclk reflects the current calculated clock */
263 if (desired >= host->mclk) {
264 clk = MCI_CLK_BYPASS;
265 if (variant->st_clkdiv)
266 clk |= MCI_ST_UX500_NEG_EDGE;
267 host->cclk = host->mclk;
268 } else if (variant->st_clkdiv) {
270 * DB8500 TRM says f = mclk / (clkdiv + 2)
271 * => clkdiv = (mclk / f) - 2
272 * Round the divider up so we don't exceed the max
275 clk = DIV_ROUND_UP(host->mclk, desired) - 2;
278 host->cclk = host->mclk / (clk + 2);
281 * PL180 TRM says f = mclk / (2 * (clkdiv + 1))
282 * => clkdiv = mclk / (2 * f) - 1
284 clk = host->mclk / (2 * desired) - 1;
287 host->cclk = host->mclk / (2 * (clk + 1));
290 clk |= variant->clkreg_enable;
291 clk |= MCI_CLK_ENABLE;
292 /* This hasn't proven to be worthwhile */
293 /* clk |= MCI_CLK_PWRSAVE; */
296 /* Set actual clock for debug */
297 host->mmc->actual_clock = host->cclk;
299 if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4)
301 if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8)
302 clk |= MCI_ST_8BIT_BUS;
304 if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50 ||
305 host->mmc->ios.timing == MMC_TIMING_MMC_DDR52)
306 clk |= MCI_ST_UX500_NEG_EDGE;
308 mmci_write_clkreg(host, clk);
312 mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
314 writel(0, host->base + MMCICOMMAND);
321 mmc_request_done(host->mmc, mrq);
323 pm_runtime_mark_last_busy(mmc_dev(host->mmc));
324 pm_runtime_put_autosuspend(mmc_dev(host->mmc));
327 static void mmci_set_mask1(struct mmci_host *host, unsigned int mask)
329 void __iomem *base = host->base;
331 if (host->singleirq) {
332 unsigned int mask0 = readl(base + MMCIMASK0);
334 mask0 &= ~MCI_IRQ1MASK;
337 writel(mask0, base + MMCIMASK0);
340 writel(mask, base + MMCIMASK1);
343 static void mmci_stop_data(struct mmci_host *host)
345 mmci_write_datactrlreg(host, 0);
346 mmci_set_mask1(host, 0);
350 static void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
352 unsigned int flags = SG_MITER_ATOMIC;
354 if (data->flags & MMC_DATA_READ)
355 flags |= SG_MITER_TO_SG;
357 flags |= SG_MITER_FROM_SG;
359 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
363 * All the DMA operation mode stuff goes inside this ifdef.
364 * This assumes that you have a generic DMA device interface,
365 * no custom DMA interfaces are supported.
367 #ifdef CONFIG_DMA_ENGINE
368 static void mmci_dma_setup(struct mmci_host *host)
370 const char *rxname, *txname;
373 host->dma_rx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "rx");
374 host->dma_tx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "tx");
376 /* initialize pre request cookie */
377 host->next_data.cookie = 1;
379 /* Try to acquire a generic DMA engine slave channel */
381 dma_cap_set(DMA_SLAVE, mask);
384 * If only an RX channel is specified, the driver will
385 * attempt to use it bidirectionally, however if it is
386 * is specified but cannot be located, DMA will be disabled.
388 if (host->dma_rx_channel && !host->dma_tx_channel)
389 host->dma_tx_channel = host->dma_rx_channel;
391 if (host->dma_rx_channel)
392 rxname = dma_chan_name(host->dma_rx_channel);
396 if (host->dma_tx_channel)
397 txname = dma_chan_name(host->dma_tx_channel);
401 dev_info(mmc_dev(host->mmc), "DMA channels RX %s, TX %s\n",
405 * Limit the maximum segment size in any SG entry according to
406 * the parameters of the DMA engine device.
408 if (host->dma_tx_channel) {
409 struct device *dev = host->dma_tx_channel->device->dev;
410 unsigned int max_seg_size = dma_get_max_seg_size(dev);
412 if (max_seg_size < host->mmc->max_seg_size)
413 host->mmc->max_seg_size = max_seg_size;
415 if (host->dma_rx_channel) {
416 struct device *dev = host->dma_rx_channel->device->dev;
417 unsigned int max_seg_size = dma_get_max_seg_size(dev);
419 if (max_seg_size < host->mmc->max_seg_size)
420 host->mmc->max_seg_size = max_seg_size;
425 * This is used in or so inline it
426 * so it can be discarded.
428 static inline void mmci_dma_release(struct mmci_host *host)
430 if (host->dma_rx_channel)
431 dma_release_channel(host->dma_rx_channel);
432 if (host->dma_tx_channel)
433 dma_release_channel(host->dma_tx_channel);
434 host->dma_rx_channel = host->dma_tx_channel = NULL;
437 static void mmci_dma_data_error(struct mmci_host *host)
439 dev_err(mmc_dev(host->mmc), "error during DMA transfer!\n");
440 dmaengine_terminate_all(host->dma_current);
441 host->dma_current = NULL;
442 host->dma_desc_current = NULL;
443 host->data->host_cookie = 0;
446 static void mmci_dma_unmap(struct mmci_host *host, struct mmc_data *data)
448 struct dma_chan *chan;
449 enum dma_data_direction dir;
451 if (data->flags & MMC_DATA_READ) {
452 dir = DMA_FROM_DEVICE;
453 chan = host->dma_rx_channel;
456 chan = host->dma_tx_channel;
459 dma_unmap_sg(chan->device->dev, data->sg, data->sg_len, dir);
462 static void mmci_dma_finalize(struct mmci_host *host, struct mmc_data *data)
467 /* Wait up to 1ms for the DMA to complete */
469 status = readl(host->base + MMCISTATUS);
470 if (!(status & MCI_RXDATAAVLBLMASK) || i >= 100)
476 * Check to see whether we still have some data left in the FIFO -
477 * this catches DMA controllers which are unable to monitor the
478 * DMALBREQ and DMALSREQ signals while allowing us to DMA to non-
479 * contiguous buffers. On TX, we'll get a FIFO underrun error.
481 if (status & MCI_RXDATAAVLBLMASK) {
482 mmci_dma_data_error(host);
487 if (!data->host_cookie)
488 mmci_dma_unmap(host, data);
491 * Use of DMA with scatter-gather is impossible.
492 * Give up with DMA and switch back to PIO mode.
494 if (status & MCI_RXDATAAVLBLMASK) {
495 dev_err(mmc_dev(host->mmc), "buggy DMA detected. Taking evasive action.\n");
496 mmci_dma_release(host);
499 host->dma_current = NULL;
500 host->dma_desc_current = NULL;
503 /* prepares DMA channel and DMA descriptor, returns non-zero on failure */
504 static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
505 struct dma_chan **dma_chan,
506 struct dma_async_tx_descriptor **dma_desc)
508 struct variant_data *variant = host->variant;
509 struct dma_slave_config conf = {
510 .src_addr = host->phybase + MMCIFIFO,
511 .dst_addr = host->phybase + MMCIFIFO,
512 .src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES,
513 .dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES,
514 .src_maxburst = variant->fifohalfsize >> 2, /* # of words */
515 .dst_maxburst = variant->fifohalfsize >> 2, /* # of words */
518 struct dma_chan *chan;
519 struct dma_device *device;
520 struct dma_async_tx_descriptor *desc;
521 enum dma_data_direction buffer_dirn;
524 if (data->flags & MMC_DATA_READ) {
525 conf.direction = DMA_DEV_TO_MEM;
526 buffer_dirn = DMA_FROM_DEVICE;
527 chan = host->dma_rx_channel;
529 conf.direction = DMA_MEM_TO_DEV;
530 buffer_dirn = DMA_TO_DEVICE;
531 chan = host->dma_tx_channel;
534 /* If there's no DMA channel, fall back to PIO */
538 /* If less than or equal to the fifo size, don't bother with DMA */
539 if (data->blksz * data->blocks <= variant->fifosize)
542 device = chan->device;
543 nr_sg = dma_map_sg(device->dev, data->sg, data->sg_len, buffer_dirn);
547 dmaengine_slave_config(chan, &conf);
548 desc = dmaengine_prep_slave_sg(chan, data->sg, nr_sg,
549 conf.direction, DMA_CTRL_ACK);
559 dma_unmap_sg(device->dev, data->sg, data->sg_len, buffer_dirn);
563 static inline int mmci_dma_prep_data(struct mmci_host *host,
564 struct mmc_data *data)
566 /* Check if next job is already prepared. */
567 if (host->dma_current && host->dma_desc_current)
570 /* No job were prepared thus do it now. */
571 return __mmci_dma_prep_data(host, data, &host->dma_current,
572 &host->dma_desc_current);
575 static inline int mmci_dma_prep_next(struct mmci_host *host,
576 struct mmc_data *data)
578 struct mmci_host_next *nd = &host->next_data;
579 return __mmci_dma_prep_data(host, data, &nd->dma_chan, &nd->dma_desc);
582 static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
585 struct mmc_data *data = host->data;
587 ret = mmci_dma_prep_data(host, host->data);
591 /* Okay, go for it. */
592 dev_vdbg(mmc_dev(host->mmc),
593 "Submit MMCI DMA job, sglen %d blksz %04x blks %04x flags %08x\n",
594 data->sg_len, data->blksz, data->blocks, data->flags);
595 dmaengine_submit(host->dma_desc_current);
596 dma_async_issue_pending(host->dma_current);
598 datactrl |= MCI_DPSM_DMAENABLE;
600 /* Trigger the DMA transfer */
601 mmci_write_datactrlreg(host, datactrl);
604 * Let the MMCI say when the data is ended and it's time
605 * to fire next DMA request. When that happens, MMCI will
606 * call mmci_data_end()
608 writel(readl(host->base + MMCIMASK0) | MCI_DATAENDMASK,
609 host->base + MMCIMASK0);
613 static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
615 struct mmci_host_next *next = &host->next_data;
617 WARN_ON(data->host_cookie && data->host_cookie != next->cookie);
618 WARN_ON(!data->host_cookie && (next->dma_desc || next->dma_chan));
620 host->dma_desc_current = next->dma_desc;
621 host->dma_current = next->dma_chan;
622 next->dma_desc = NULL;
623 next->dma_chan = NULL;
626 static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq,
629 struct mmci_host *host = mmc_priv(mmc);
630 struct mmc_data *data = mrq->data;
631 struct mmci_host_next *nd = &host->next_data;
636 BUG_ON(data->host_cookie);
638 if (mmci_validate_data(host, data))
641 if (!mmci_dma_prep_next(host, data))
642 data->host_cookie = ++nd->cookie < 0 ? 1 : nd->cookie;
645 static void mmci_post_request(struct mmc_host *mmc, struct mmc_request *mrq,
648 struct mmci_host *host = mmc_priv(mmc);
649 struct mmc_data *data = mrq->data;
651 if (!data || !data->host_cookie)
654 mmci_dma_unmap(host, data);
657 struct mmci_host_next *next = &host->next_data;
658 struct dma_chan *chan;
659 if (data->flags & MMC_DATA_READ)
660 chan = host->dma_rx_channel;
662 chan = host->dma_tx_channel;
663 dmaengine_terminate_all(chan);
665 next->dma_desc = NULL;
666 next->dma_chan = NULL;
671 /* Blank functions if the DMA engine is not available */
672 static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
675 static inline void mmci_dma_setup(struct mmci_host *host)
679 static inline void mmci_dma_release(struct mmci_host *host)
683 static inline void mmci_dma_unmap(struct mmci_host *host, struct mmc_data *data)
687 static inline void mmci_dma_finalize(struct mmci_host *host,
688 struct mmc_data *data)
692 static inline void mmci_dma_data_error(struct mmci_host *host)
696 static inline int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
701 #define mmci_pre_request NULL
702 #define mmci_post_request NULL
706 static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
708 struct variant_data *variant = host->variant;
709 unsigned int datactrl, timeout, irqmask;
710 unsigned long long clks;
714 dev_dbg(mmc_dev(host->mmc), "blksz %04x blks %04x flags %08x\n",
715 data->blksz, data->blocks, data->flags);
718 host->size = data->blksz * data->blocks;
719 data->bytes_xfered = 0;
721 clks = (unsigned long long)data->timeout_ns * host->cclk;
722 do_div(clks, 1000000000UL);
724 timeout = data->timeout_clks + (unsigned int)clks;
727 writel(timeout, base + MMCIDATATIMER);
728 writel(host->size, base + MMCIDATALENGTH);
730 blksz_bits = ffs(data->blksz) - 1;
731 BUG_ON(1 << blksz_bits != data->blksz);
733 if (variant->blksz_datactrl16)
734 datactrl = MCI_DPSM_ENABLE | (data->blksz << 16);
736 datactrl = MCI_DPSM_ENABLE | blksz_bits << 4;
738 if (data->flags & MMC_DATA_READ)
739 datactrl |= MCI_DPSM_DIRECTION;
741 /* The ST Micro variants has a special bit to enable SDIO */
742 if (variant->sdio && host->mmc->card)
743 if (mmc_card_sdio(host->mmc->card)) {
745 * The ST Micro variants has a special bit
750 datactrl |= MCI_ST_DPSM_SDIOEN;
753 * The ST Micro variant for SDIO small write transfers
754 * needs to have clock H/W flow control disabled,
755 * otherwise the transfer will not start. The threshold
756 * depends on the rate of MCLK.
758 if (data->flags & MMC_DATA_WRITE &&
760 (host->size <= 8 && host->mclk > 50000000)))
761 clk = host->clk_reg & ~variant->clkreg_enable;
763 clk = host->clk_reg | variant->clkreg_enable;
765 mmci_write_clkreg(host, clk);
768 if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50 ||
769 host->mmc->ios.timing == MMC_TIMING_MMC_DDR52)
770 datactrl |= MCI_ST_DPSM_DDRMODE;
773 * Attempt to use DMA operation mode, if this
774 * should fail, fall back to PIO mode
776 if (!mmci_dma_start_data(host, datactrl))
779 /* IRQ mode, map the SG list for CPU reading/writing */
780 mmci_init_sg(host, data);
782 if (data->flags & MMC_DATA_READ) {
783 irqmask = MCI_RXFIFOHALFFULLMASK;
786 * If we have less than the fifo 'half-full' threshold to
787 * transfer, trigger a PIO interrupt as soon as any data
790 if (host->size < variant->fifohalfsize)
791 irqmask |= MCI_RXDATAAVLBLMASK;
794 * We don't actually need to include "FIFO empty" here
795 * since its implicit in "FIFO half empty".
797 irqmask = MCI_TXFIFOHALFEMPTYMASK;
800 mmci_write_datactrlreg(host, datactrl);
801 writel(readl(base + MMCIMASK0) & ~MCI_DATAENDMASK, base + MMCIMASK0);
802 mmci_set_mask1(host, irqmask);
806 mmci_start_command(struct mmci_host *host, struct mmc_command *cmd, u32 c)
808 void __iomem *base = host->base;
810 dev_dbg(mmc_dev(host->mmc), "op %02x arg %08x flags %08x\n",
811 cmd->opcode, cmd->arg, cmd->flags);
813 if (readl(base + MMCICOMMAND) & MCI_CPSM_ENABLE) {
814 writel(0, base + MMCICOMMAND);
818 c |= cmd->opcode | MCI_CPSM_ENABLE;
819 if (cmd->flags & MMC_RSP_PRESENT) {
820 if (cmd->flags & MMC_RSP_136)
821 c |= MCI_CPSM_LONGRSP;
822 c |= MCI_CPSM_RESPONSE;
825 c |= MCI_CPSM_INTERRUPT;
829 writel(cmd->arg, base + MMCIARGUMENT);
830 writel(c, base + MMCICOMMAND);
834 mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
837 /* First check for errors */
838 if (status & (MCI_DATACRCFAIL|MCI_DATATIMEOUT|MCI_STARTBITERR|
839 MCI_TXUNDERRUN|MCI_RXOVERRUN)) {
842 /* Terminate the DMA transfer */
843 if (dma_inprogress(host)) {
844 mmci_dma_data_error(host);
845 mmci_dma_unmap(host, data);
849 * Calculate how far we are into the transfer. Note that
850 * the data counter gives the number of bytes transferred
851 * on the MMC bus, not on the host side. On reads, this
852 * can be as much as a FIFO-worth of data ahead. This
853 * matters for FIFO overruns only.
855 remain = readl(host->base + MMCIDATACNT);
856 success = data->blksz * data->blocks - remain;
858 dev_dbg(mmc_dev(host->mmc), "MCI ERROR IRQ, status 0x%08x at 0x%08x\n",
860 if (status & MCI_DATACRCFAIL) {
861 /* Last block was not successful */
863 data->error = -EILSEQ;
864 } else if (status & MCI_DATATIMEOUT) {
865 data->error = -ETIMEDOUT;
866 } else if (status & MCI_STARTBITERR) {
867 data->error = -ECOMM;
868 } else if (status & MCI_TXUNDERRUN) {
870 } else if (status & MCI_RXOVERRUN) {
871 if (success > host->variant->fifosize)
872 success -= host->variant->fifosize;
877 data->bytes_xfered = round_down(success, data->blksz);
880 if (status & MCI_DATABLOCKEND)
881 dev_err(mmc_dev(host->mmc), "stray MCI_DATABLOCKEND interrupt\n");
883 if (status & MCI_DATAEND || data->error) {
884 if (dma_inprogress(host))
885 mmci_dma_finalize(host, data);
886 mmci_stop_data(host);
889 /* The error clause is handled above, success! */
890 data->bytes_xfered = data->blksz * data->blocks;
892 if (!data->stop || host->mrq->sbc) {
893 mmci_request_end(host, data->mrq);
895 mmci_start_command(host, data->stop, 0);
901 mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd,
904 void __iomem *base = host->base;
905 bool sbc = (cmd == host->mrq->sbc);
906 bool busy_resp = host->variant->busy_detect &&
907 (cmd->flags & MMC_RSP_BUSY);
909 /* Check if we need to wait for busy completion. */
910 if (host->busy_status && (status & MCI_ST_CARDBUSY))
913 /* Enable busy completion if needed and supported. */
914 if (!host->busy_status && busy_resp &&
915 !(status & (MCI_CMDCRCFAIL|MCI_CMDTIMEOUT)) &&
916 (readl(base + MMCISTATUS) & MCI_ST_CARDBUSY)) {
917 writel(readl(base + MMCIMASK0) | MCI_ST_BUSYEND,
919 host->busy_status = status & (MCI_CMDSENT|MCI_CMDRESPEND);
923 /* At busy completion, mask the IRQ and complete the request. */
924 if (host->busy_status) {
925 writel(readl(base + MMCIMASK0) & ~MCI_ST_BUSYEND,
927 host->busy_status = 0;
932 if (status & MCI_CMDTIMEOUT) {
933 cmd->error = -ETIMEDOUT;
934 } else if (status & MCI_CMDCRCFAIL && cmd->flags & MMC_RSP_CRC) {
935 cmd->error = -EILSEQ;
937 cmd->resp[0] = readl(base + MMCIRESPONSE0);
938 cmd->resp[1] = readl(base + MMCIRESPONSE1);
939 cmd->resp[2] = readl(base + MMCIRESPONSE2);
940 cmd->resp[3] = readl(base + MMCIRESPONSE3);
943 if ((!sbc && !cmd->data) || cmd->error) {
945 /* Terminate the DMA transfer */
946 if (dma_inprogress(host)) {
947 mmci_dma_data_error(host);
948 mmci_dma_unmap(host, host->data);
950 mmci_stop_data(host);
952 mmci_request_end(host, host->mrq);
954 mmci_start_command(host, host->mrq->cmd, 0);
955 } else if (!(cmd->data->flags & MMC_DATA_READ)) {
956 mmci_start_data(host, cmd->data);
960 static int mmci_pio_read(struct mmci_host *host, char *buffer, unsigned int remain)
962 void __iomem *base = host->base;
965 int host_remain = host->size;
968 int count = host_remain - (readl(base + MMCIFIFOCNT) << 2);
977 * SDIO especially may want to send something that is
978 * not divisible by 4 (as opposed to card sectors
979 * etc). Therefore make sure to always read the last bytes
980 * while only doing full 32-bit reads towards the FIFO.
982 if (unlikely(count & 0x3)) {
984 unsigned char buf[4];
985 ioread32_rep(base + MMCIFIFO, buf, 1);
986 memcpy(ptr, buf, count);
988 ioread32_rep(base + MMCIFIFO, ptr, count >> 2);
992 ioread32_rep(base + MMCIFIFO, ptr, count >> 2);
997 host_remain -= count;
1002 status = readl(base + MMCISTATUS);
1003 } while (status & MCI_RXDATAAVLBL);
1005 return ptr - buffer;
1008 static int mmci_pio_write(struct mmci_host *host, char *buffer, unsigned int remain, u32 status)
1010 struct variant_data *variant = host->variant;
1011 void __iomem *base = host->base;
1015 unsigned int count, maxcnt;
1017 maxcnt = status & MCI_TXFIFOEMPTY ?
1018 variant->fifosize : variant->fifohalfsize;
1019 count = min(remain, maxcnt);
1022 * SDIO especially may want to send something that is
1023 * not divisible by 4 (as opposed to card sectors
1024 * etc), and the FIFO only accept full 32-bit writes.
1025 * So compensate by adding +3 on the count, a single
1026 * byte become a 32bit write, 7 bytes will be two
1029 iowrite32_rep(base + MMCIFIFO, ptr, (count + 3) >> 2);
1037 status = readl(base + MMCISTATUS);
1038 } while (status & MCI_TXFIFOHALFEMPTY);
1040 return ptr - buffer;
1044 * PIO data transfer IRQ handler.
1046 static irqreturn_t mmci_pio_irq(int irq, void *dev_id)
1048 struct mmci_host *host = dev_id;
1049 struct sg_mapping_iter *sg_miter = &host->sg_miter;
1050 struct variant_data *variant = host->variant;
1051 void __iomem *base = host->base;
1052 unsigned long flags;
1055 status = readl(base + MMCISTATUS);
1057 dev_dbg(mmc_dev(host->mmc), "irq1 (pio) %08x\n", status);
1059 local_irq_save(flags);
1062 unsigned int remain, len;
1066 * For write, we only need to test the half-empty flag
1067 * here - if the FIFO is completely empty, then by
1068 * definition it is more than half empty.
1070 * For read, check for data available.
1072 if (!(status & (MCI_TXFIFOHALFEMPTY|MCI_RXDATAAVLBL)))
1075 if (!sg_miter_next(sg_miter))
1078 buffer = sg_miter->addr;
1079 remain = sg_miter->length;
1082 if (status & MCI_RXACTIVE)
1083 len = mmci_pio_read(host, buffer, remain);
1084 if (status & MCI_TXACTIVE)
1085 len = mmci_pio_write(host, buffer, remain, status);
1087 sg_miter->consumed = len;
1095 status = readl(base + MMCISTATUS);
1098 sg_miter_stop(sg_miter);
1100 local_irq_restore(flags);
1103 * If we have less than the fifo 'half-full' threshold to transfer,
1104 * trigger a PIO interrupt as soon as any data is available.
1106 if (status & MCI_RXACTIVE && host->size < variant->fifohalfsize)
1107 mmci_set_mask1(host, MCI_RXDATAAVLBLMASK);
1110 * If we run out of data, disable the data IRQs; this
1111 * prevents a race where the FIFO becomes empty before
1112 * the chip itself has disabled the data path, and
1113 * stops us racing with our data end IRQ.
1115 if (host->size == 0) {
1116 mmci_set_mask1(host, 0);
1117 writel(readl(base + MMCIMASK0) | MCI_DATAENDMASK, base + MMCIMASK0);
1124 * Handle completion of command and data transfers.
1126 static irqreturn_t mmci_irq(int irq, void *dev_id)
1128 struct mmci_host *host = dev_id;
1132 spin_lock(&host->lock);
1135 struct mmc_command *cmd;
1136 struct mmc_data *data;
1138 status = readl(host->base + MMCISTATUS);
1140 if (host->singleirq) {
1141 if (status & readl(host->base + MMCIMASK1))
1142 mmci_pio_irq(irq, dev_id);
1144 status &= ~MCI_IRQ1MASK;
1148 * We intentionally clear the MCI_ST_CARDBUSY IRQ here (if it's
1149 * enabled) since the HW seems to be triggering the IRQ on both
1150 * edges while monitoring DAT0 for busy completion.
1152 status &= readl(host->base + MMCIMASK0);
1153 writel(status, host->base + MMCICLEAR);
1155 dev_dbg(mmc_dev(host->mmc), "irq0 (data+cmd) %08x\n", status);
1158 if ((status|host->busy_status) & (MCI_CMDCRCFAIL|MCI_CMDTIMEOUT|
1159 MCI_CMDSENT|MCI_CMDRESPEND) && cmd)
1160 mmci_cmd_irq(host, cmd, status);
1163 if (status & (MCI_DATACRCFAIL|MCI_DATATIMEOUT|MCI_STARTBITERR|
1164 MCI_TXUNDERRUN|MCI_RXOVERRUN|MCI_DATAEND|
1165 MCI_DATABLOCKEND) && data)
1166 mmci_data_irq(host, data, status);
1168 /* Don't poll for busy completion in irq context. */
1169 if (host->busy_status)
1170 status &= ~MCI_ST_CARDBUSY;
1175 spin_unlock(&host->lock);
1177 return IRQ_RETVAL(ret);
1180 static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1182 struct mmci_host *host = mmc_priv(mmc);
1183 unsigned long flags;
1185 WARN_ON(host->mrq != NULL);
1187 mrq->cmd->error = mmci_validate_data(host, mrq->data);
1188 if (mrq->cmd->error) {
1189 mmc_request_done(mmc, mrq);
1193 pm_runtime_get_sync(mmc_dev(mmc));
1195 spin_lock_irqsave(&host->lock, flags);
1200 mmci_get_next_data(host, mrq->data);
1202 if (mrq->data && mrq->data->flags & MMC_DATA_READ)
1203 mmci_start_data(host, mrq->data);
1206 mmci_start_command(host, mrq->sbc, 0);
1208 mmci_start_command(host, mrq->cmd, 0);
1210 spin_unlock_irqrestore(&host->lock, flags);
1213 static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1215 struct mmci_host *host = mmc_priv(mmc);
1216 struct variant_data *variant = host->variant;
1218 unsigned long flags;
1221 pm_runtime_get_sync(mmc_dev(mmc));
1223 if (host->plat->ios_handler &&
1224 host->plat->ios_handler(mmc_dev(mmc), ios))
1225 dev_err(mmc_dev(mmc), "platform ios_handler failed\n");
1227 switch (ios->power_mode) {
1229 if (!IS_ERR(mmc->supply.vmmc))
1230 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1232 if (!IS_ERR(mmc->supply.vqmmc) && host->vqmmc_enabled) {
1233 regulator_disable(mmc->supply.vqmmc);
1234 host->vqmmc_enabled = false;
1239 if (!IS_ERR(mmc->supply.vmmc))
1240 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
1243 * The ST Micro variant doesn't have the PL180s MCI_PWR_UP
1244 * and instead uses MCI_PWR_ON so apply whatever value is
1245 * configured in the variant data.
1247 pwr |= variant->pwrreg_powerup;
1251 if (!IS_ERR(mmc->supply.vqmmc) && !host->vqmmc_enabled) {
1252 ret = regulator_enable(mmc->supply.vqmmc);
1254 dev_err(mmc_dev(mmc),
1255 "failed to enable vqmmc regulator\n");
1257 host->vqmmc_enabled = true;
1264 if (variant->signal_direction && ios->power_mode != MMC_POWER_OFF) {
1266 * The ST Micro variant has some additional bits
1267 * indicating signal direction for the signals in
1268 * the SD/MMC bus and feedback-clock usage.
1270 pwr |= host->pwr_reg_add;
1272 if (ios->bus_width == MMC_BUS_WIDTH_4)
1273 pwr &= ~MCI_ST_DATA74DIREN;
1274 else if (ios->bus_width == MMC_BUS_WIDTH_1)
1275 pwr &= (~MCI_ST_DATA74DIREN &
1276 ~MCI_ST_DATA31DIREN &
1277 ~MCI_ST_DATA2DIREN);
1280 if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
1281 if (host->hw_designer != AMBA_VENDOR_ST)
1285 * The ST Micro variant use the ROD bit for something
1286 * else and only has OD (Open Drain).
1293 * If clock = 0 and the variant requires the MMCIPOWER to be used for
1294 * gating the clock, the MCI_PWR_ON bit is cleared.
1296 if (!ios->clock && variant->pwrreg_clkgate)
1299 spin_lock_irqsave(&host->lock, flags);
1301 mmci_set_clkreg(host, ios->clock);
1302 mmci_write_pwrreg(host, pwr);
1303 mmci_reg_delay(host);
1305 spin_unlock_irqrestore(&host->lock, flags);
1307 pm_runtime_mark_last_busy(mmc_dev(mmc));
1308 pm_runtime_put_autosuspend(mmc_dev(mmc));
1311 static int mmci_get_cd(struct mmc_host *mmc)
1313 struct mmci_host *host = mmc_priv(mmc);
1314 struct mmci_platform_data *plat = host->plat;
1315 unsigned int status = mmc_gpio_get_cd(mmc);
1317 if (status == -ENOSYS) {
1319 return 1; /* Assume always present */
1321 status = plat->status(mmc_dev(host->mmc));
1326 static int mmci_sig_volt_switch(struct mmc_host *mmc, struct mmc_ios *ios)
1330 if (!IS_ERR(mmc->supply.vqmmc)) {
1332 pm_runtime_get_sync(mmc_dev(mmc));
1334 switch (ios->signal_voltage) {
1335 case MMC_SIGNAL_VOLTAGE_330:
1336 ret = regulator_set_voltage(mmc->supply.vqmmc,
1339 case MMC_SIGNAL_VOLTAGE_180:
1340 ret = regulator_set_voltage(mmc->supply.vqmmc,
1343 case MMC_SIGNAL_VOLTAGE_120:
1344 ret = regulator_set_voltage(mmc->supply.vqmmc,
1350 dev_warn(mmc_dev(mmc), "Voltage switch failed\n");
1352 pm_runtime_mark_last_busy(mmc_dev(mmc));
1353 pm_runtime_put_autosuspend(mmc_dev(mmc));
1359 static struct mmc_host_ops mmci_ops = {
1360 .request = mmci_request,
1361 .pre_req = mmci_pre_request,
1362 .post_req = mmci_post_request,
1363 .set_ios = mmci_set_ios,
1364 .get_ro = mmc_gpio_get_ro,
1365 .get_cd = mmci_get_cd,
1366 .start_signal_voltage_switch = mmci_sig_volt_switch,
1369 static int mmci_of_parse(struct device_node *np, struct mmc_host *mmc)
1371 struct mmci_host *host = mmc_priv(mmc);
1372 int ret = mmc_of_parse(mmc);
1377 if (of_get_property(np, "st,sig-dir-dat0", NULL))
1378 host->pwr_reg_add |= MCI_ST_DATA0DIREN;
1379 if (of_get_property(np, "st,sig-dir-dat2", NULL))
1380 host->pwr_reg_add |= MCI_ST_DATA2DIREN;
1381 if (of_get_property(np, "st,sig-dir-dat31", NULL))
1382 host->pwr_reg_add |= MCI_ST_DATA31DIREN;
1383 if (of_get_property(np, "st,sig-dir-dat74", NULL))
1384 host->pwr_reg_add |= MCI_ST_DATA74DIREN;
1385 if (of_get_property(np, "st,sig-dir-cmd", NULL))
1386 host->pwr_reg_add |= MCI_ST_CMDDIREN;
1387 if (of_get_property(np, "st,sig-pin-fbclk", NULL))
1388 host->pwr_reg_add |= MCI_ST_FBCLKEN;
1390 if (of_get_property(np, "mmc-cap-mmc-highspeed", NULL))
1391 mmc->caps |= MMC_CAP_MMC_HIGHSPEED;
1392 if (of_get_property(np, "mmc-cap-sd-highspeed", NULL))
1393 mmc->caps |= MMC_CAP_SD_HIGHSPEED;
1398 static int mmci_probe(struct amba_device *dev,
1399 const struct amba_id *id)
1401 struct mmci_platform_data *plat = dev->dev.platform_data;
1402 struct device_node *np = dev->dev.of_node;
1403 struct variant_data *variant = id->data;
1404 struct mmci_host *host;
1405 struct mmc_host *mmc;
1408 /* Must have platform data or Device Tree. */
1410 dev_err(&dev->dev, "No plat data or DT found\n");
1415 plat = devm_kzalloc(&dev->dev, sizeof(*plat), GFP_KERNEL);
1420 mmc = mmc_alloc_host(sizeof(struct mmci_host), &dev->dev);
1424 ret = mmci_of_parse(np, mmc);
1428 host = mmc_priv(mmc);
1431 host->hw_designer = amba_manf(dev);
1432 host->hw_revision = amba_rev(dev);
1433 dev_dbg(mmc_dev(mmc), "designer ID = 0x%02x\n", host->hw_designer);
1434 dev_dbg(mmc_dev(mmc), "revision = 0x%01x\n", host->hw_revision);
1436 host->clk = devm_clk_get(&dev->dev, NULL);
1437 if (IS_ERR(host->clk)) {
1438 ret = PTR_ERR(host->clk);
1442 ret = clk_prepare_enable(host->clk);
1447 host->variant = variant;
1448 host->mclk = clk_get_rate(host->clk);
1450 * According to the spec, mclk is max 100 MHz,
1451 * so we try to adjust the clock down to this,
1454 if (host->mclk > 100000000) {
1455 ret = clk_set_rate(host->clk, 100000000);
1458 host->mclk = clk_get_rate(host->clk);
1459 dev_dbg(mmc_dev(mmc), "eventual mclk rate: %u Hz\n",
1463 host->phybase = dev->res.start;
1464 host->base = devm_ioremap_resource(&dev->dev, &dev->res);
1465 if (IS_ERR(host->base)) {
1466 ret = PTR_ERR(host->base);
1471 * The ARM and ST versions of the block have slightly different
1472 * clock divider equations which means that the minimum divider
1475 if (variant->st_clkdiv)
1476 mmc->f_min = DIV_ROUND_UP(host->mclk, 257);
1478 mmc->f_min = DIV_ROUND_UP(host->mclk, 512);
1480 * If no maximum operating frequency is supplied, fall back to use
1481 * the module parameter, which has a (low) default value in case it
1482 * is not specified. Either value must not exceed the clock rate into
1483 * the block, of course.
1486 mmc->f_max = min(host->mclk, mmc->f_max);
1488 mmc->f_max = min(host->mclk, fmax);
1489 dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max);
1491 /* Get regulators and the supported OCR mask */
1492 mmc_regulator_get_supply(mmc);
1493 if (!mmc->ocr_avail)
1494 mmc->ocr_avail = plat->ocr_mask;
1495 else if (plat->ocr_mask)
1496 dev_warn(mmc_dev(mmc), "Platform OCR mask is ignored\n");
1498 /* DT takes precedence over platform data. */
1500 if (!plat->cd_invert)
1501 mmc->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
1502 mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
1505 /* We support these capabilities. */
1506 mmc->caps |= MMC_CAP_CMD23;
1508 if (variant->busy_detect) {
1509 mmci_ops.card_busy = mmci_card_busy;
1510 mmci_write_datactrlreg(host, MCI_ST_DPSM_BUSYMODE);
1511 mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY;
1512 mmc->max_busy_timeout = 0;
1515 mmc->ops = &mmci_ops;
1517 /* We support these PM capabilities. */
1518 mmc->pm_caps |= MMC_PM_KEEP_POWER;
1523 mmc->max_segs = NR_SG;
1526 * Since only a certain number of bits are valid in the data length
1527 * register, we must ensure that we don't exceed 2^num-1 bytes in a
1530 mmc->max_req_size = (1 << variant->datalength_bits) - 1;
1533 * Set the maximum segment size. Since we aren't doing DMA
1534 * (yet) we are only limited by the data length register.
1536 mmc->max_seg_size = mmc->max_req_size;
1539 * Block size can be up to 2048 bytes, but must be a power of two.
1541 mmc->max_blk_size = 1 << 11;
1544 * Limit the number of blocks transferred so that we don't overflow
1545 * the maximum request size.
1547 mmc->max_blk_count = mmc->max_req_size >> 11;
1549 spin_lock_init(&host->lock);
1551 writel(0, host->base + MMCIMASK0);
1552 writel(0, host->base + MMCIMASK1);
1553 writel(0xfff, host->base + MMCICLEAR);
1555 /* If DT, cd/wp gpios must be supplied through it. */
1556 if (!np && gpio_is_valid(plat->gpio_cd)) {
1557 ret = mmc_gpio_request_cd(mmc, plat->gpio_cd, 0);
1561 if (!np && gpio_is_valid(plat->gpio_wp)) {
1562 ret = mmc_gpio_request_ro(mmc, plat->gpio_wp);
1567 ret = devm_request_irq(&dev->dev, dev->irq[0], mmci_irq, IRQF_SHARED,
1568 DRIVER_NAME " (cmd)", host);
1573 host->singleirq = true;
1575 ret = devm_request_irq(&dev->dev, dev->irq[1], mmci_pio_irq,
1576 IRQF_SHARED, DRIVER_NAME " (pio)", host);
1581 writel(MCI_IRQENABLE, host->base + MMCIMASK0);
1583 amba_set_drvdata(dev, mmc);
1585 dev_info(&dev->dev, "%s: PL%03x manf %x rev%u at 0x%08llx irq %d,%d (pio)\n",
1586 mmc_hostname(mmc), amba_part(dev), amba_manf(dev),
1587 amba_rev(dev), (unsigned long long)dev->res.start,
1588 dev->irq[0], dev->irq[1]);
1590 mmci_dma_setup(host);
1592 pm_runtime_set_autosuspend_delay(&dev->dev, 50);
1593 pm_runtime_use_autosuspend(&dev->dev);
1594 pm_runtime_put(&dev->dev);
1601 clk_disable_unprepare(host->clk);
1607 static int mmci_remove(struct amba_device *dev)
1609 struct mmc_host *mmc = amba_get_drvdata(dev);
1612 struct mmci_host *host = mmc_priv(mmc);
1615 * Undo pm_runtime_put() in probe. We use the _sync
1616 * version here so that we can access the primecell.
1618 pm_runtime_get_sync(&dev->dev);
1620 mmc_remove_host(mmc);
1622 writel(0, host->base + MMCIMASK0);
1623 writel(0, host->base + MMCIMASK1);
1625 writel(0, host->base + MMCICOMMAND);
1626 writel(0, host->base + MMCIDATACTRL);
1628 mmci_dma_release(host);
1629 clk_disable_unprepare(host->clk);
1637 static void mmci_save(struct mmci_host *host)
1639 unsigned long flags;
1641 spin_lock_irqsave(&host->lock, flags);
1643 writel(0, host->base + MMCIMASK0);
1644 if (host->variant->pwrreg_nopower) {
1645 writel(0, host->base + MMCIDATACTRL);
1646 writel(0, host->base + MMCIPOWER);
1647 writel(0, host->base + MMCICLOCK);
1649 mmci_reg_delay(host);
1651 spin_unlock_irqrestore(&host->lock, flags);
1654 static void mmci_restore(struct mmci_host *host)
1656 unsigned long flags;
1658 spin_lock_irqsave(&host->lock, flags);
1660 if (host->variant->pwrreg_nopower) {
1661 writel(host->clk_reg, host->base + MMCICLOCK);
1662 writel(host->datactrl_reg, host->base + MMCIDATACTRL);
1663 writel(host->pwr_reg, host->base + MMCIPOWER);
1665 writel(MCI_IRQENABLE, host->base + MMCIMASK0);
1666 mmci_reg_delay(host);
1668 spin_unlock_irqrestore(&host->lock, flags);
1671 static int mmci_runtime_suspend(struct device *dev)
1673 struct amba_device *adev = to_amba_device(dev);
1674 struct mmc_host *mmc = amba_get_drvdata(adev);
1677 struct mmci_host *host = mmc_priv(mmc);
1678 pinctrl_pm_select_sleep_state(dev);
1680 clk_disable_unprepare(host->clk);
1686 static int mmci_runtime_resume(struct device *dev)
1688 struct amba_device *adev = to_amba_device(dev);
1689 struct mmc_host *mmc = amba_get_drvdata(adev);
1692 struct mmci_host *host = mmc_priv(mmc);
1693 clk_prepare_enable(host->clk);
1695 pinctrl_pm_select_default_state(dev);
1702 static const struct dev_pm_ops mmci_dev_pm_ops = {
1703 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
1704 pm_runtime_force_resume)
1705 SET_PM_RUNTIME_PM_OPS(mmci_runtime_suspend, mmci_runtime_resume, NULL)
1708 static struct amba_id mmci_ids[] = {
1712 .data = &variant_arm,
1717 .data = &variant_arm_extended_fifo,
1722 .data = &variant_arm_extended_fifo_hwfc,
1727 .data = &variant_arm,
1729 /* ST Micro variants */
1733 .data = &variant_u300,
1738 .data = &variant_nomadik,
1743 .data = &variant_u300,
1748 .data = &variant_ux500,
1753 .data = &variant_ux500v2,
1758 MODULE_DEVICE_TABLE(amba, mmci_ids);
1760 static struct amba_driver mmci_driver = {
1762 .name = DRIVER_NAME,
1763 .pm = &mmci_dev_pm_ops,
1765 .probe = mmci_probe,
1766 .remove = mmci_remove,
1767 .id_table = mmci_ids,
1770 module_amba_driver(mmci_driver);
1772 module_param(fmax, uint, 0444);
1774 MODULE_DESCRIPTION("ARM PrimeCell PL180/181 Multimedia Card Interface driver");
1775 MODULE_LICENSE("GPL");