2 # Touchscreen driver configuration
4 menuconfig INPUT_TOUCHSCREEN
7 Say Y here, and a list of supported touchscreens will be displayed.
8 This option doesn't affect the kernel.
14 config TOUCHSCREEN_88PM860X
15 tristate "Marvell 88PM860x touchscreen"
16 depends on MFD_88PM860X
18 Say Y here if you have a 88PM860x PMIC and want to enable
19 support for the built-in touchscreen.
23 To compile this driver as a module, choose M here: the
24 module will be called 88pm860x-ts.
26 config TOUCHSCREEN_ADS7846
27 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
29 depends on HWMON = n || HWMON
31 Say Y here if you have a touchscreen interface using the
32 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
33 and your board-specific setup code includes that in its
36 If HWMON is selected, and the driver is told the reference voltage
37 on your board, you will also get hwmon interfaces for the voltage
38 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
40 If unsure, say N (but it's safe to say "Y").
42 To compile this driver as a module, choose M here: the
43 module will be called ads7846.
45 config TOUCHSCREEN_AD7877
46 tristate "AD7877 based touchscreens"
49 Say Y here if you have a touchscreen interface using the
50 AD7877 controller, and your board-specific initialization
51 code includes that in its table of SPI devices.
53 If unsure, say N (but it's safe to say "Y").
55 To compile this driver as a module, choose M here: the
56 module will be called ad7877.
58 config TOUCHSCREEN_AD7879
59 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
61 Say Y here if you want to support a touchscreen interface using
62 the AD7879-1/AD7889-1 controller.
64 You should select a bus connection too.
66 To compile this driver as a module, choose M here: the
67 module will be called ad7879.
69 config TOUCHSCREEN_AD7879_I2C
70 tristate "support I2C bus connection"
71 depends on TOUCHSCREEN_AD7879 && I2C
73 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
75 To compile this driver as a module, choose M here: the
76 module will be called ad7879-i2c.
78 config TOUCHSCREEN_AD7879_SPI
79 tristate "support SPI bus connection"
80 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
82 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
84 If unsure, say N (but it's safe to say "Y").
86 To compile this driver as a module, choose M here: the
87 module will be called ad7879-spi.
89 config TOUCHSCREEN_BITSY
90 tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
91 depends on SA1100_BITSY
94 Say Y here if you have the h3600 (Bitsy) touchscreen.
98 To compile this driver as a module, choose M here: the
99 module will be called h3600_ts_input.
101 config TOUCHSCREEN_CY8CTMG110
102 tristate "cy8ctmg110 touchscreen"
107 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
112 To compile this driver as a module, choose M here: the
113 module will be called cy8ctmg110_ts.
115 config TOUCHSCREEN_DA9034
116 tristate "Touchscreen support for Dialog Semiconductor DA9034"
117 depends on PMIC_DA903X
120 Say Y here to enable the support for the touchscreen found
121 on Dialog Semiconductor DA9034 PMIC.
123 config TOUCHSCREEN_DYNAPRO
124 tristate "Dynapro serial touchscreen"
127 Say Y here if you have a Dynapro serial touchscreen connected to
132 To compile this driver as a module, choose M here: the
133 module will be called dynapro.
135 config TOUCHSCREEN_HAMPSHIRE
136 tristate "Hampshire serial touchscreen"
139 Say Y here if you have a Hampshire serial touchscreen connected to
144 To compile this driver as a module, choose M here: the
145 module will be called hampshire.
147 config TOUCHSCREEN_EETI
148 tristate "EETI touchscreen panel support"
151 Say Y here to enable support for I2C connected EETI touch panels.
153 To compile this driver as a module, choose M here: the
154 module will be called eeti_ts.
156 config TOUCHSCREEN_FUJITSU
157 tristate "Fujitsu serial touchscreen"
160 Say Y here if you have the Fujitsu touchscreen (such as one
161 installed in Lifebook P series laptop) connected to your
166 To compile this driver as a module, choose M here: the
167 module will be called fujitsu-ts.
169 config TOUCHSCREEN_S3C2410
170 tristate "Samsung S3C2410/generic touchscreen input driver"
171 depends on ARCH_S3C2410 || SAMSUNG_DEV_TS
174 Say Y here if you have the s3c2410 touchscreen.
178 To compile this driver as a module, choose M here: the
179 module will be called s3c2410_ts.
181 config TOUCHSCREEN_GUNZE
182 tristate "Gunze AHL-51S touchscreen"
185 Say Y here if you have the Gunze AHL-51 touchscreen connected to
190 To compile this driver as a module, choose M here: the
191 module will be called gunze.
193 config TOUCHSCREEN_ELO
194 tristate "Elo serial touchscreens"
197 Say Y here if you have an Elo serial touchscreen connected to
202 To compile this driver as a module, choose M here: the
203 module will be called elo.
205 config TOUCHSCREEN_WACOM_W8001
206 tristate "Wacom W8001 penabled serial touchscreen"
209 Say Y here if you have an Wacom W8001 penabled serial touchscreen
210 connected to your system.
214 To compile this driver as a module, choose M here: the
215 module will be called wacom_w8001.
217 config TOUCHSCREEN_MCS5000
218 tristate "MELFAS MCS-5000 touchscreen"
221 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
226 To compile this driver as a module, choose M here: the
227 module will be called mcs5000_ts.
229 config TOUCHSCREEN_MTOUCH
230 tristate "MicroTouch serial touchscreens"
233 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
238 To compile this driver as a module, choose M here: the
239 module will be called mtouch.
241 config TOUCHSCREEN_INEXIO
242 tristate "iNexio serial touchscreens"
245 Say Y here if you have an iNexio serial touchscreen connected to
250 To compile this driver as a module, choose M here: the
251 module will be called inexio.
253 config TOUCHSCREEN_MK712
254 tristate "ICS MicroClock MK712 touchscreen"
256 Say Y here if you have the ICS MicroClock MK712 touchscreen
257 controller chip in your system.
261 To compile this driver as a module, choose M here: the
262 module will be called mk712.
264 config TOUCHSCREEN_HP600
265 tristate "HP Jornada 6xx touchscreen"
266 depends on SH_HP6XX && SH_ADC
268 Say Y here if you have a HP Jornada 620/660/680/690 and want to
269 support the built-in touchscreen.
271 To compile this driver as a module, choose M here: the
272 module will be called hp680_ts_input.
274 config TOUCHSCREEN_HP7XX
275 tristate "HP Jornada 7xx touchscreen"
276 depends on SA1100_JORNADA720_SSP
278 Say Y here if you have a HP Jornada 710/720/728 and want
279 to support the built-in touchscreen.
281 To compile this driver as a module, choose M here: the
282 module will be called jornada720_ts.
284 config TOUCHSCREEN_HTCPEN
285 tristate "HTC Shift X9500 touchscreen"
288 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
289 Clio / Shangrila and want to support the built-in touchscreen.
293 To compile this driver as a module, choose M here: the
294 module will be called htcpen.
296 config TOUCHSCREEN_PENMOUNT
297 tristate "Penmount serial touchscreen"
300 Say Y here if you have a Penmount serial touchscreen connected to
305 To compile this driver as a module, choose M here: the
306 module will be called penmount.
308 config TOUCHSCREEN_QT602240
309 tristate "QT602240 I2C Touchscreen"
312 Say Y here if you have the AT42QT602240/ATMXT224 I2C touchscreen
313 connected to your system.
317 To compile this driver as a module, choose M here: the
318 module will be called qt602240_ts.
320 config TOUCHSCREEN_MIGOR
321 tristate "Renesas MIGO-R touchscreen"
322 depends on SH_MIGOR && I2C
324 Say Y here to enable MIGO-R touchscreen support.
328 To compile this driver as a module, choose M here: the
329 module will be called migor_ts.
331 config TOUCHSCREEN_PANJIT_I2C
332 tristate "PANJIT I2C touchscreen driver"
336 Say Y here to enable PANJIT I2C capacitive touchscreen support,
337 covering devices such as the MGG1010AI06 and EGG1010AI06
341 To compile this driver as a module, choose M here: the module will
342 be called panjit_i2c.
344 config TOUCHSCREEN_SYNAPTICS_I2C_RMI
345 tristate "Synaptics i2c touchscreen"
348 This enables support for Synaptics RMI over I2C based touchscreens.
350 config TOUCHSCREEN_TOUCHRIGHT
351 tristate "Touchright serial touchscreen"
354 Say Y here if you have a Touchright serial touchscreen connected to
359 To compile this driver as a module, choose M here: the
360 module will be called touchright.
362 config TOUCHSCREEN_TOUCHWIN
363 tristate "Touchwin serial touchscreen"
366 Say Y here if you have a Touchwin serial touchscreen connected to
371 To compile this driver as a module, choose M here: the
372 module will be called touchwin.
374 config TOUCHSCREEN_ATMEL_TSADCC
375 tristate "Atmel Touchscreen Interface"
376 depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
378 Say Y here if you have a 4-wire touchscreen connected to the
379 ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
383 To compile this driver as a module, choose M here: the
384 module will be called atmel_tsadcc.
386 config TOUCHSCREEN_UCB1400
387 tristate "Philips UCB1400 touchscreen"
389 depends on UCB1400_CORE
391 This enables support for the Philips UCB1400 touchscreen interface.
392 The UCB1400 is an AC97 audio codec. The touchscreen interface
393 will be initialized only after the ALSA subsystem has been
394 brought up and the UCB1400 detected. You therefore have to
395 configure ALSA support as well (either built-in or modular,
396 independently of whether this driver is itself built-in or
397 modular) for this driver to work.
399 To compile this driver as a module, choose M here: the
400 module will be called ucb1400_ts.
402 config TOUCHSCREEN_WM97XX
403 tristate "Support for WM97xx AC97 touchscreen controllers"
406 Say Y here if you have a Wolfson Microelectronics WM97xx
407 touchscreen connected to your system. Note that this option
408 only enables core driver, you will also need to select
409 support for appropriate chip below.
413 To compile this driver as a module, choose M here: the
414 module will be called wm97xx-ts.
416 config TOUCHSCREEN_WM9705
417 bool "WM9705 Touchscreen interface support"
418 depends on TOUCHSCREEN_WM97XX
421 Say Y here to enable support for the Wolfson Microelectronics
422 WM9705 touchscreen controller.
424 config TOUCHSCREEN_WM9712
425 bool "WM9712 Touchscreen interface support"
426 depends on TOUCHSCREEN_WM97XX
429 Say Y here to enable support for the Wolfson Microelectronics
430 WM9712 touchscreen controller.
432 config TOUCHSCREEN_WM9713
433 bool "WM9713 Touchscreen interface support"
434 depends on TOUCHSCREEN_WM97XX
437 Say Y here to enable support for the Wolfson Microelectronics
438 WM9713 touchscreen controller.
440 config TOUCHSCREEN_WM97XX_ATMEL
441 tristate "WM97xx Atmel accelerated touch"
442 depends on TOUCHSCREEN_WM97XX && (AVR32 || ARCH_AT91)
444 Say Y here for support for streaming mode with WM97xx touchscreens
445 on Atmel AT91 or AVR32 systems with an AC97C module.
447 Be aware that this will use channel B in the controller for
448 streaming data, this must not conflict with other AC97C drivers.
452 To compile this driver as a module, choose M here: the module will
453 be called atmel-wm97xx.
455 config TOUCHSCREEN_WM97XX_MAINSTONE
456 tristate "WM97xx Mainstone/Palm accelerated touch"
457 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
459 Say Y here for support for streaming mode with WM97xx touchscreens
460 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
464 To compile this driver as a module, choose M here: the
465 module will be called mainstone-wm97xx.
467 config TOUCHSCREEN_WM97XX_ZYLONITE
468 tristate "Zylonite accelerated touch"
469 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
470 select TOUCHSCREEN_WM9713
472 Say Y here for support for streaming mode with the touchscreen
477 To compile this driver as a module, choose M here: the
478 module will be called zylonite-wm97xx.
480 config TOUCHSCREEN_USB_COMPOSITE
481 tristate "USB Touchscreen Driver"
482 depends on USB_ARCH_HAS_HCD
485 USB Touchscreen driver for:
486 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
487 - PanJit TouchSet USB
488 - 3M MicroTouch USB (EX II series)
490 - some other eTurboTouch
493 - IRTOUCHSYSTEMS/UNITOP
495 - GoTop Super_Q2/GogoPen/PenPower tablets
496 - JASTEC USB Touch Controller/DigiTech DTR-02U
497 - Zytronic controllers
499 Have a look at <http://linux.chapter7.ch/touchkit/> for
500 a usage description and the required user-space stuff.
502 To compile this driver as a module, choose M here: the
503 module will be called usbtouchscreen.
505 config TOUCHSCREEN_MC13783
506 tristate "Freescale MC13783 touchscreen input driver"
507 depends on MFD_MC13783
509 Say Y here if you have an Freescale MC13783 PMIC on your
510 board and want to use its touchscreen
514 To compile this driver as a module, choose M here: the
515 module will be called mc13783_ts.
517 config TOUCHSCREEN_USB_EGALAX
519 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
520 depends on TOUCHSCREEN_USB_COMPOSITE
522 config TOUCHSCREEN_USB_PANJIT
524 bool "PanJit device support" if EMBEDDED
525 depends on TOUCHSCREEN_USB_COMPOSITE
527 config TOUCHSCREEN_USB_3M
529 bool "3M/Microtouch EX II series device support" if EMBEDDED
530 depends on TOUCHSCREEN_USB_COMPOSITE
532 config TOUCHSCREEN_USB_ITM
534 bool "ITM device support" if EMBEDDED
535 depends on TOUCHSCREEN_USB_COMPOSITE
537 config TOUCHSCREEN_USB_ETURBO
539 bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
540 depends on TOUCHSCREEN_USB_COMPOSITE
542 config TOUCHSCREEN_USB_GUNZE
544 bool "Gunze AHL61 device support" if EMBEDDED
545 depends on TOUCHSCREEN_USB_COMPOSITE
547 config TOUCHSCREEN_USB_DMC_TSC10
549 bool "DMC TSC-10/25 device support" if EMBEDDED
550 depends on TOUCHSCREEN_USB_COMPOSITE
552 config TOUCHSCREEN_USB_IRTOUCH
554 bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
555 depends on TOUCHSCREEN_USB_COMPOSITE
557 config TOUCHSCREEN_USB_IDEALTEK
559 bool "IdealTEK URTC1000 device support" if EMBEDDED
560 depends on TOUCHSCREEN_USB_COMPOSITE
562 config TOUCHSCREEN_USB_GENERAL_TOUCH
564 bool "GeneralTouch Touchscreen device support" if EMBEDDED
565 depends on TOUCHSCREEN_USB_COMPOSITE
567 config TOUCHSCREEN_USB_GOTOP
569 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
570 depends on TOUCHSCREEN_USB_COMPOSITE
572 config TOUCHSCREEN_USB_JASTEC
574 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EMBEDDED
575 depends on TOUCHSCREEN_USB_COMPOSITE
577 config TOUCHSCREEN_USB_E2I
579 bool "e2i Touchscreen controller (e.g. from Mimo 740)"
580 depends on TOUCHSCREEN_USB_COMPOSITE
582 config TOUCHSCREEN_USB_ZYTRONIC
584 bool "Zytronic controller" if EMBEDDED
585 depends on TOUCHSCREEN_USB_COMPOSITE
587 config TOUCHSCREEN_USB_ETT_TC45USB
589 bool "ET&T USB series TC4UM/TC5UH touchscreen controler support" if EMBEDDED
590 depends on TOUCHSCREEN_USB_COMPOSITE
592 config TOUCHSCREEN_USB_NEXIO
594 bool "NEXIO/iNexio device support" if EMBEDDED
595 depends on TOUCHSCREEN_USB_COMPOSITE
597 config TOUCHSCREEN_TOUCHIT213
598 tristate "Sahara TouchIT-213 touchscreen"
601 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
605 To compile this driver as a module, choose M here: the
606 module will be called touchit213.
608 config TOUCHSCREEN_TSC2007
609 tristate "TSC2007 based touchscreens"
612 Say Y here if you have a TSC2007 based touchscreen.
616 To compile this driver as a module, choose M here: the
617 module will be called tsc2007.
619 config TOUCHSCREEN_W90X900
620 tristate "W90P910 touchscreen driver"
623 Say Y here if you have a W90P910 based touchscreen.
625 To compile this driver as a module, choose M here: the
626 module will be called w90p910_ts.
628 config TOUCHSCREEN_PCAP
629 tristate "Motorola PCAP touchscreen"
632 Say Y here if you have a Motorola EZX telephone and
633 want to enable support for the built-in touchscreen.
635 To compile this driver as a module, choose M here: the
636 module will be called pcap_ts.
638 config TOUCHSCREEN_TPS6507X
639 tristate "TPS6507x based touchscreens"
642 Say Y here if you have a TPS6507x based touchscreen
647 To compile this driver as a module, choose M here: the
648 module will be called tps6507x_ts.
650 config TOUCHSCREEN_STMPE
651 tristate "STMicroelectronics STMPE touchscreens"
654 Say Y here if you want support for STMicroelectronics
655 STMPE touchscreen controllers.
657 To compile this driver as a module, choose M here: the
658 module will be called stmpe-ts.