2 * Copyright (c) 2009, Intel Corporation.
4 * This program is free software; you can redistribute it and/or modify it
5 * under the terms and conditions of the GNU General Public License,
6 * version 2, as published by the Free Software Foundation.
8 * This program is distributed in the hope it will be useful, but WITHOUT
9 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
10 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
13 * You should have received a copy of the GNU General Public License along with
14 * this program; if not, write to the Free Software Foundation, Inc.,
15 * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
17 #ifndef __PSB_INTEL_REG_H__
18 #define __PSB_INTEL_REG_H__
31 # define GPIO_CLOCK_DIR_MASK (1 << 0)
32 # define GPIO_CLOCK_DIR_IN (0 << 1)
33 # define GPIO_CLOCK_DIR_OUT (1 << 1)
34 # define GPIO_CLOCK_VAL_MASK (1 << 2)
35 # define GPIO_CLOCK_VAL_OUT (1 << 3)
36 # define GPIO_CLOCK_VAL_IN (1 << 4)
37 # define GPIO_CLOCK_PULLUP_DISABLE (1 << 5)
38 # define GPIO_DATA_DIR_MASK (1 << 8)
39 # define GPIO_DATA_DIR_IN (0 << 9)
40 # define GPIO_DATA_DIR_OUT (1 << 9)
41 # define GPIO_DATA_VAL_MASK (1 << 10)
42 # define GPIO_DATA_VAL_OUT (1 << 11)
43 # define GPIO_DATA_VAL_IN (1 << 12)
44 # define GPIO_DATA_PULLUP_DISABLE (1 << 13)
46 #define GMBUS0 0x5100 /* clock/port select */
47 #define GMBUS_RATE_100KHZ (0<<8)
48 #define GMBUS_RATE_50KHZ (1<<8)
49 #define GMBUS_RATE_400KHZ (2<<8) /* reserved on Pineview */
50 #define GMBUS_RATE_1MHZ (3<<8) /* reserved on Pineview */
51 #define GMBUS_HOLD_EXT (1<<7) /* 300ns hold time, rsvd on Pineview */
52 #define GMBUS_PORT_DISABLED 0
53 #define GMBUS_PORT_SSC 1
54 #define GMBUS_PORT_VGADDC 2
55 #define GMBUS_PORT_PANEL 3
56 #define GMBUS_PORT_DPC 4 /* HDMIC */
57 #define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */
59 #define GMBUS_PORT_DPD 7 /* HDMID */
60 #define GMBUS_NUM_PORTS 8
61 #define GMBUS1 0x5104 /* command/status */
62 #define GMBUS_SW_CLR_INT (1<<31)
63 #define GMBUS_SW_RDY (1<<30)
64 #define GMBUS_ENT (1<<29) /* enable timeout */
65 #define GMBUS_CYCLE_NONE (0<<25)
66 #define GMBUS_CYCLE_WAIT (1<<25)
67 #define GMBUS_CYCLE_INDEX (2<<25)
68 #define GMBUS_CYCLE_STOP (4<<25)
69 #define GMBUS_BYTE_COUNT_SHIFT 16
70 #define GMBUS_SLAVE_INDEX_SHIFT 8
71 #define GMBUS_SLAVE_ADDR_SHIFT 1
72 #define GMBUS_SLAVE_READ (1<<0)
73 #define GMBUS_SLAVE_WRITE (0<<0)
74 #define GMBUS2 0x5108 /* status */
75 #define GMBUS_INUSE (1<<15)
76 #define GMBUS_HW_WAIT_PHASE (1<<14)
77 #define GMBUS_STALL_TIMEOUT (1<<13)
78 #define GMBUS_INT (1<<12)
79 #define GMBUS_HW_RDY (1<<11)
80 #define GMBUS_SATOER (1<<10)
81 #define GMBUS_ACTIVE (1<<9)
82 #define GMBUS3 0x510c /* data buffer bytes 3-0 */
83 #define GMBUS4 0x5110 /* interrupt mask (Pineview+) */
84 #define GMBUS_SLAVE_TIMEOUT_EN (1<<4)
85 #define GMBUS_NAK_EN (1<<3)
86 #define GMBUS_IDLE_EN (1<<2)
87 #define GMBUS_HW_WAIT_EN (1<<1)
88 #define GMBUS_HW_RDY_EN (1<<0)
89 #define GMBUS5 0x5120 /* byte index */
90 #define GMBUS_2BYTE_INDEX_EN (1<<31)
92 #define BLC_PWM_CTL 0x61254
93 #define BLC_PWM_CTL2 0x61250
94 #define PWM_ENABLE (1 << 31)
95 #define PWM_LEGACY_MODE (1 << 30)
96 #define PWM_PIPE_B (1 << 29)
97 #define BLC_PWM_CTL_C 0x62254
98 #define BLC_PWM_CTL2_C 0x62250
99 #define BACKLIGHT_MODULATION_FREQ_SHIFT (17)
101 * This is the most significant 15 bits of the number of backlight cycles in a
102 * complete cycle of the modulated backlight control.
104 * The actual value is this field multiplied by two.
106 #define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17)
107 #define BLM_LEGACY_MODE (1 << 16)
109 * This is the number of cycles out of the backlight modulation cycle for which
110 * the backlight is on.
112 * This field must be no greater than the number of cycles in the complete
113 * backlight modulation cycle.
115 #define BACKLIGHT_DUTY_CYCLE_SHIFT (0)
116 #define BACKLIGHT_DUTY_CYCLE_MASK (0xffff)
118 #define I915_GCFGC 0xf0
119 #define I915_LOW_FREQUENCY_ENABLE (1 << 7)
120 #define I915_DISPLAY_CLOCK_190_200_MHZ (0 << 4)
121 #define I915_DISPLAY_CLOCK_333_MHZ (4 << 4)
122 #define I915_DISPLAY_CLOCK_MASK (7 << 4)
124 #define I855_HPLLCC 0xc0
125 #define I855_CLOCK_CONTROL_MASK (3 << 0)
126 #define I855_CLOCK_133_200 (0 << 0)
127 #define I855_CLOCK_100_200 (1 << 0)
128 #define I855_CLOCK_100_133 (2 << 0)
129 #define I855_CLOCK_166_250 (3 << 0)
131 /* I830 CRTC registers */
132 #define HTOTAL_A 0x60000
133 #define HBLANK_A 0x60004
134 #define HSYNC_A 0x60008
135 #define VTOTAL_A 0x6000c
136 #define VBLANK_A 0x60010
137 #define VSYNC_A 0x60014
138 #define PIPEASRC 0x6001c
139 #define BCLRPAT_A 0x60020
140 #define VSYNCSHIFT_A 0x60028
142 #define HTOTAL_B 0x61000
143 #define HBLANK_B 0x61004
144 #define HSYNC_B 0x61008
145 #define VTOTAL_B 0x6100c
146 #define VBLANK_B 0x61010
147 #define VSYNC_B 0x61014
148 #define PIPEBSRC 0x6101c
149 #define BCLRPAT_B 0x61020
150 #define VSYNCSHIFT_B 0x61028
152 #define HTOTAL_C 0x62000
153 #define HBLANK_C 0x62004
154 #define HSYNC_C 0x62008
155 #define VTOTAL_C 0x6200c
156 #define VBLANK_C 0x62010
157 #define VSYNC_C 0x62014
158 #define PIPECSRC 0x6201c
159 #define BCLRPAT_C 0x62020
160 #define VSYNCSHIFT_C 0x62028
162 #define PP_STATUS 0x61200
163 # define PP_ON (1 << 31)
165 * Indicates that all dependencies of the panel are on:
169 * - LVDS/DVOB/DVOC on
171 #define PP_READY (1 << 30)
172 #define PP_SEQUENCE_NONE (0 << 28)
173 #define PP_SEQUENCE_ON (1 << 28)
174 #define PP_SEQUENCE_OFF (2 << 28)
175 #define PP_SEQUENCE_MASK 0x30000000
176 #define PP_CONTROL 0x61204
177 #define POWER_TARGET_ON (1 << 0)
179 #define LVDSPP_ON 0x61208
180 #define LVDSPP_OFF 0x6120c
181 #define PP_CYCLE 0x61210
183 #define PP_ON_DELAYS 0x61208 /* Cedartrail */
184 #define PP_OFF_DELAYS 0x6120c /* Cedartrail */
186 #define PFIT_CONTROL 0x61230
187 #define PFIT_ENABLE (1 << 31)
188 #define PFIT_PIPE_MASK (3 << 29)
189 #define PFIT_PIPE_SHIFT 29
190 #define PFIT_SCALING_MODE_PILLARBOX (1 << 27)
191 #define PFIT_SCALING_MODE_LETTERBOX (3 << 26)
192 #define VERT_INTERP_DISABLE (0 << 10)
193 #define VERT_INTERP_BILINEAR (1 << 10)
194 #define VERT_INTERP_MASK (3 << 10)
195 #define VERT_AUTO_SCALE (1 << 9)
196 #define HORIZ_INTERP_DISABLE (0 << 6)
197 #define HORIZ_INTERP_BILINEAR (1 << 6)
198 #define HORIZ_INTERP_MASK (3 << 6)
199 #define HORIZ_AUTO_SCALE (1 << 5)
200 #define PANEL_8TO6_DITHER_ENABLE (1 << 3)
202 #define PFIT_PGM_RATIOS 0x61234
203 #define PFIT_VERT_SCALE_MASK 0xfff00000
204 #define PFIT_HORIZ_SCALE_MASK 0x0000fff0
206 #define PFIT_AUTO_RATIOS 0x61238
208 #define DPLL_A 0x06014
209 #define DPLL_B 0x06018
210 #define DPLL_VCO_ENABLE (1 << 31)
211 #define DPLL_DVO_HIGH_SPEED (1 << 30)
212 #define DPLL_SYNCLOCK_ENABLE (1 << 29)
213 #define DPLL_VGA_MODE_DIS (1 << 28)
214 #define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */
215 #define DPLLB_MODE_LVDS (2 << 26) /* i915 */
216 #define DPLL_MODE_MASK (3 << 26)
217 #define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */
218 #define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */
219 #define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */
220 #define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */
221 #define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */
222 #define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */
223 #define DPLL_LOCK (1 << 15) /* CDV */
226 * The i830 generation, in DAC/serial mode, defines p1 as two plus this
227 * bitfield, or just 2 if PLL_P1_DIVIDE_BY_TWO is set.
229 # define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000
231 * The i830 generation, in LVDS mode, defines P1 as the bit number set within
232 * this field (only one bit may be set).
234 #define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000
235 #define DPLL_FPA01_P1_POST_DIV_SHIFT 16
236 #define PLL_P2_DIVIDE_BY_4 (1 << 23) /* i830, required
238 # define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */
239 #define PLL_REF_INPUT_DREFCLK (0 << 13)
240 #define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */
241 #define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO
243 #define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13)
244 #define PLL_REF_INPUT_MASK (3 << 13)
245 #define PLL_LOAD_PULSE_PHASE_SHIFT 9
247 * Parallel to Serial Load Pulse phase selection.
248 * Selects the phase for the 10X DPLL clock for the PCIe
249 * digital display port. The range is 4 to 13; 10 or more
250 * is just a flip delay. The default is 6
252 #define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT)
253 #define DISPLAY_RATE_SELECT_FPA1 (1 << 8)
256 * SDVO multiplier for 945G/GM. Not used on 965.
258 * DPLL_MD_UDI_MULTIPLIER_MASK
260 #define SDVO_MULTIPLIER_MASK 0x000000ff
261 #define SDVO_MULTIPLIER_SHIFT_HIRES 4
262 #define SDVO_MULTIPLIER_SHIFT_VGA 0
267 /* Pipe A SDVO/UDI clock multiplier/divider register for G965. */
268 #define DPLL_A_MD 0x0601c
269 /* Pipe B SDVO/UDI clock multiplier/divider register for G965. */
270 #define DPLL_B_MD 0x06020
272 * UDI pixel divider, controlling how many pixels are stuffed into a packet.
274 * Value is pixels minus 1. Must be set to 1 pixel for SDVO.
276 #define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000
277 #define DPLL_MD_UDI_DIVIDER_SHIFT 24
278 /* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */
279 #define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000
280 #define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16
282 * SDVO/UDI pixel multiplier.
284 * SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus
285 * clock rate is 10 times the DPLL clock. At low resolution/refresh rate
286 * modes, the bus rate would be below the limits, so SDVO allows for stuffing
287 * dummy bytes in the datastream at an increased clock rate, with both sides of
288 * the link knowing how many bytes are fill.
290 * So, for a mode with a dotclock of 65Mhz, we would want to double the clock
291 * rate to 130Mhz to get a bus rate of 1.30Ghz. The DPLL clock rate would be
292 * set to 130Mhz, and the SDVO multiplier set to 2x in this register and
293 * through an SDVO command.
295 * This register field has values of multiplication factor minus 1, with
296 * a maximum multiplier of 5 for SDVO.
298 #define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00
299 #define DPLL_MD_UDI_MULTIPLIER_SHIFT 8
301 * SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK.
302 * This best be set to the default value (3) or the CRT won't work. No,
303 * I don't entirely understand what this does...
305 #define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f
306 #define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0
308 #define DPLL_TEST 0x606c
309 #define DPLLB_TEST_SDVO_DIV_1 (0 << 22)
310 #define DPLLB_TEST_SDVO_DIV_2 (1 << 22)
311 #define DPLLB_TEST_SDVO_DIV_4 (2 << 22)
312 #define DPLLB_TEST_SDVO_DIV_MASK (3 << 22)
313 #define DPLLB_TEST_N_BYPASS (1 << 19)
314 #define DPLLB_TEST_M_BYPASS (1 << 18)
315 #define DPLLB_INPUT_BUFFER_ENABLE (1 << 16)
316 #define DPLLA_TEST_N_BYPASS (1 << 3)
317 #define DPLLA_TEST_M_BYPASS (1 << 2)
318 #define DPLLA_INPUT_BUFFER_ENABLE (1 << 0)
321 #define ADPA_DAC_ENABLE (1 << 31)
322 #define ADPA_DAC_DISABLE 0
323 #define ADPA_PIPE_SELECT_MASK (1 << 30)
324 #define ADPA_PIPE_A_SELECT 0
325 #define ADPA_PIPE_B_SELECT (1 << 30)
326 #define ADPA_USE_VGA_HVPOLARITY (1 << 15)
327 #define ADPA_SETS_HVPOLARITY 0
328 #define ADPA_VSYNC_CNTL_DISABLE (1 << 11)
329 #define ADPA_VSYNC_CNTL_ENABLE 0
330 #define ADPA_HSYNC_CNTL_DISABLE (1 << 10)
331 #define ADPA_HSYNC_CNTL_ENABLE 0
332 #define ADPA_VSYNC_ACTIVE_HIGH (1 << 4)
333 #define ADPA_VSYNC_ACTIVE_LOW 0
334 #define ADPA_HSYNC_ACTIVE_HIGH (1 << 3)
335 #define ADPA_HSYNC_ACTIVE_LOW 0
341 #define FP_N_DIV_MASK 0x003f0000
342 #define FP_N_DIV_SHIFT 16
343 #define FP_M1_DIV_MASK 0x00003f00
344 #define FP_M1_DIV_SHIFT 8
345 #define FP_M2_DIV_MASK 0x0000003f
346 #define FP_M2_DIV_SHIFT 0
348 #define PORT_HOTPLUG_EN 0x61110
349 #define SDVOB_HOTPLUG_INT_EN (1 << 26)
350 #define SDVOC_HOTPLUG_INT_EN (1 << 25)
351 #define TV_HOTPLUG_INT_EN (1 << 18)
352 #define CRT_HOTPLUG_INT_EN (1 << 9)
353 #define CRT_HOTPLUG_FORCE_DETECT (1 << 3)
355 #define CRT_HOTPLUG_ACTIVATION_PERIOD_64 (1 << 8)
356 #define CRT_HOTPLUG_DAC_ON_TIME_2M (0 << 7)
357 #define CRT_HOTPLUG_DAC_ON_TIME_4M (1 << 7)
358 #define CRT_HOTPLUG_VOLTAGE_COMPARE_40 (0 << 5)
359 #define CRT_HOTPLUG_VOLTAGE_COMPARE_50 (1 << 5)
360 #define CRT_HOTPLUG_VOLTAGE_COMPARE_60 (2 << 5)
361 #define CRT_HOTPLUG_VOLTAGE_COMPARE_70 (3 << 5)
362 #define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK (3 << 5)
363 #define CRT_HOTPLUG_DETECT_DELAY_1G (0 << 4)
364 #define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4)
365 #define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2)
366 #define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2)
367 #define CRT_HOTPLUG_DETECT_MASK 0x000000F8
369 #define PORT_HOTPLUG_STAT 0x61114
370 #define CRT_HOTPLUG_INT_STATUS (1 << 11)
371 #define TV_HOTPLUG_INT_STATUS (1 << 10)
372 #define CRT_HOTPLUG_MONITOR_MASK (3 << 8)
373 #define CRT_HOTPLUG_MONITOR_COLOR (3 << 8)
374 #define CRT_HOTPLUG_MONITOR_MONO (2 << 8)
375 #define CRT_HOTPLUG_MONITOR_NONE (0 << 8)
376 #define SDVOC_HOTPLUG_INT_STATUS (1 << 7)
377 #define SDVOB_HOTPLUG_INT_STATUS (1 << 6)
379 #define SDVOB 0x61140
380 #define SDVOC 0x61160
381 #define SDVO_ENABLE (1 << 31)
382 #define SDVO_PIPE_B_SELECT (1 << 30)
383 #define SDVO_STALL_SELECT (1 << 29)
384 #define SDVO_INTERRUPT_ENABLE (1 << 26)
385 #define SDVO_COLOR_RANGE_16_235 (1 << 8)
386 #define SDVO_AUDIO_ENABLE (1 << 6)
389 * 915G/GM SDVO pixel multiplier.
391 * Programmed value is multiplier - 1, up to 5x.
393 * DPLL_MD_UDI_MULTIPLIER_MASK
395 #define SDVO_PORT_MULTIPLY_MASK (7 << 23)
396 #define SDVO_PORT_MULTIPLY_SHIFT 23
397 #define SDVO_PHASE_SELECT_MASK (15 << 19)
398 #define SDVO_PHASE_SELECT_DEFAULT (6 << 19)
399 #define SDVO_CLOCK_OUTPUT_INVERT (1 << 18)
400 #define SDVOC_GANG_MODE (1 << 16)
401 #define SDVO_BORDER_ENABLE (1 << 7)
402 #define SDVOB_PCIE_CONCURRENCY (1 << 3)
403 #define SDVO_DETECTED (1 << 2)
404 /* Bits to be preserved when writing */
405 #define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14))
406 #define SDVOC_PRESERVE_MASK (1 << 17)
409 * This register controls the LVDS output enable, pipe selection, and data
412 * All of the clock/data pairs are force powered down by power sequencing.
416 * Enables the LVDS port. This bit must be set before DPLLs are enabled, as
417 * the DPLL semantics change when the LVDS is assigned to that pipe.
419 #define LVDS_PORT_EN (1 << 31)
420 /* Selects pipe B for LVDS data. Must be set on pre-965. */
421 #define LVDS_PIPEB_SELECT (1 << 30)
423 /* Turns on border drawing to allow centered display. */
424 #define LVDS_BORDER_EN (1 << 15)
427 * Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per
430 #define LVDS_A0A2_CLKA_POWER_MASK (3 << 8)
431 #define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8)
432 #define LVDS_A0A2_CLKA_POWER_UP (3 << 8)
434 * Controls the A3 data pair, which contains the additional LSBs for 24 bit
435 * mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be
438 #define LVDS_A3_POWER_MASK (3 << 6)
439 #define LVDS_A3_POWER_DOWN (0 << 6)
440 #define LVDS_A3_POWER_UP (3 << 6)
442 * Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP
445 #define LVDS_CLKB_POWER_MASK (3 << 4)
446 #define LVDS_CLKB_POWER_DOWN (0 << 4)
447 #define LVDS_CLKB_POWER_UP (3 << 4)
449 * Controls the B0-B3 data pairs. This must be set to match the DPLL p2
450 * setting for whether we are in dual-channel mode. The B3 pair will
451 * additionally only be powered up when LVDS_A3_POWER_UP is set.
453 #define LVDS_B0B3_POWER_MASK (3 << 2)
454 #define LVDS_B0B3_POWER_DOWN (0 << 2)
455 #define LVDS_B0B3_POWER_UP (3 << 2)
457 #define PIPEACONF 0x70008
458 #define PIPEACONF_ENABLE (1 << 31)
459 #define PIPEACONF_DISABLE 0
460 #define PIPEACONF_DOUBLE_WIDE (1 << 30)
461 #define PIPECONF_ACTIVE (1 << 30)
462 #define I965_PIPECONF_ACTIVE (1 << 30)
463 #define PIPECONF_DSIPLL_LOCK (1 << 29)
464 #define PIPEACONF_SINGLE_WIDE 0
465 #define PIPEACONF_PIPE_UNLOCKED 0
466 #define PIPEACONF_DSR (1 << 26)
467 #define PIPEACONF_PIPE_LOCKED (1 << 25)
468 #define PIPEACONF_PALETTE 0
469 #define PIPECONF_FORCE_BORDER (1 << 25)
470 #define PIPEACONF_GAMMA (1 << 24)
471 #define PIPECONF_PROGRESSIVE (0 << 21)
472 #define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21)
473 #define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21)
474 #define PIPECONF_PLANE_OFF (1 << 19)
475 #define PIPECONF_CURSOR_OFF (1 << 18)
477 #define PIPEBCONF 0x71008
478 #define PIPEBCONF_ENABLE (1 << 31)
479 #define PIPEBCONF_DISABLE 0
480 #define PIPEBCONF_DOUBLE_WIDE (1 << 30)
481 #define PIPEBCONF_DISABLE 0
482 #define PIPEBCONF_GAMMA (1 << 24)
483 #define PIPEBCONF_PALETTE 0
485 #define PIPECCONF 0x72008
487 #define PIPEBGCMAXRED 0x71010
488 #define PIPEBGCMAXGREEN 0x71014
489 #define PIPEBGCMAXBLUE 0x71018
491 #define PIPEASTAT 0x70024
492 #define PIPEBSTAT 0x71024
493 #define PIPECSTAT 0x72024
494 #define PIPE_VBLANK_INTERRUPT_STATUS (1UL << 1)
495 #define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL << 2)
496 #define PIPE_VBLANK_CLEAR (1 << 1)
497 #define PIPE_VBLANK_STATUS (1 << 1)
498 #define PIPE_TE_STATUS (1UL << 6)
499 #define PIPE_DPST_EVENT_STATUS (1UL << 7)
500 #define PIPE_VSYNC_CLEAR (1UL << 9)
501 #define PIPE_VSYNC_STATUS (1UL << 9)
502 #define PIPE_HDMI_AUDIO_UNDERRUN_STATUS (1UL << 10)
503 #define PIPE_HDMI_AUDIO_BUFFER_DONE_STATUS (1UL << 11)
504 #define PIPE_VBLANK_INTERRUPT_ENABLE (1UL << 17)
505 #define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL << 18)
506 #define PIPE_TE_ENABLE (1UL << 22)
507 #define PIPE_DPST_EVENT_ENABLE (1UL << 23)
508 #define PIPE_VSYNC_ENABL (1UL << 25)
509 #define PIPE_HDMI_AUDIO_UNDERRUN (1UL << 26)
510 #define PIPE_HDMI_AUDIO_BUFFER_DONE (1UL << 27)
511 #define PIPE_FIFO_UNDERRUN (1UL << 31)
512 #define PIPE_HDMI_AUDIO_INT_MASK (PIPE_HDMI_AUDIO_UNDERRUN | \
513 PIPE_HDMI_AUDIO_BUFFER_DONE)
514 #define PIPE_EVENT_MASK ((1 << 29)|(1 << 28)|(1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)|(1 << 22)|(1 << 21)|(1 << 20)|(1 << 16))
515 #define PIPE_VBLANK_MASK ((1 << 25)|(1 << 24)|(1 << 18)|(1 << 17))
516 #define HISTOGRAM_INT_CONTROL 0x61268
517 #define HISTOGRAM_BIN_DATA 0X61264
518 #define HISTOGRAM_LOGIC_CONTROL 0x61260
519 #define PWM_CONTROL_LOGIC 0x61250
520 #define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL << 10)
521 #define HISTOGRAM_INTERRUPT_ENABLE (1UL << 31)
522 #define HISTOGRAM_LOGIC_ENABLE (1UL << 31)
523 #define PWM_LOGIC_ENABLE (1UL << 31)
524 #define PWM_PHASEIN_ENABLE (1UL << 25)
525 #define PWM_PHASEIN_INT_ENABLE (1UL << 24)
526 #define PWM_PHASEIN_VB_COUNT 0x00001f00
527 #define PWM_PHASEIN_INC 0x0000001f
528 #define HISTOGRAM_INT_CTRL_CLEAR (1UL << 30)
529 #define DPST_YUV_LUMA_MODE 0
531 struct dpst_ie_histogram_control {
535 uint32_t bin_reg_index:7;
537 uint32_t bin_reg_func_select:1;
538 uint32_t sync_to_phase_in:1;
539 uint32_t alt_enhancement_mode:2;
540 uint32_t reserved1:1;
541 uint32_t sync_to_phase_in_count:8;
542 uint32_t histogram_mode_select:1;
543 uint32_t reserved2:4;
544 uint32_t ie_pipe_assignment:1;
545 uint32_t ie_mode_table_enabled:1;
546 uint32_t ie_histogram_enable:1;
551 struct dpst_guardband {
555 uint32_t guardband:22;
556 uint32_t guardband_interrupt_delay:8;
557 uint32_t interrupt_status:1;
558 uint32_t interrupt_enable:1;
563 #define PIPEAFRAMEHIGH 0x70040
564 #define PIPEAFRAMEPIXEL 0x70044
565 #define PIPEBFRAMEHIGH 0x71040
566 #define PIPEBFRAMEPIXEL 0x71044
567 #define PIPECFRAMEHIGH 0x72040
568 #define PIPECFRAMEPIXEL 0x72044
569 #define PIPE_FRAME_HIGH_MASK 0x0000ffff
570 #define PIPE_FRAME_HIGH_SHIFT 0
571 #define PIPE_FRAME_LOW_MASK 0xff000000
572 #define PIPE_FRAME_LOW_SHIFT 24
573 #define PIPE_PIXEL_MASK 0x00ffffff
574 #define PIPE_PIXEL_SHIFT 0
576 #define FW_BLC_SELF 0x20e0
577 #define FW_BLC_SELF_EN (1<<15)
579 #define DSPARB 0x70030
580 #define DSPFW1 0x70034
581 #define DSP_FIFO_SR_WM_MASK 0xFF800000
582 #define DSP_FIFO_SR_WM_SHIFT 23
583 #define CURSOR_B_FIFO_WM_MASK 0x003F0000
584 #define CURSOR_B_FIFO_WM_SHIFT 16
585 #define DSPFW2 0x70038
586 #define CURSOR_A_FIFO_WM_MASK 0x3F00
587 #define CURSOR_A_FIFO_WM_SHIFT 8
588 #define DSP_PLANE_C_FIFO_WM_MASK 0x7F
589 #define DSP_PLANE_C_FIFO_WM_SHIFT 0
590 #define DSPFW3 0x7003c
591 #define DSPFW4 0x70050
592 #define DSPFW5 0x70054
593 #define DSP_PLANE_B_FIFO_WM1_SHIFT 24
594 #define DSP_PLANE_A_FIFO_WM1_SHIFT 16
595 #define CURSOR_B_FIFO_WM1_SHIFT 8
596 #define CURSOR_FIFO_SR_WM1_SHIFT 0
597 #define DSPFW6 0x70058
598 #define DSPCHICKENBIT 0x70400
599 #define DSPACNTR 0x70180
600 #define DSPBCNTR 0x71180
601 #define DSPCCNTR 0x72180
602 #define DISPLAY_PLANE_ENABLE (1 << 31)
603 #define DISPLAY_PLANE_DISABLE 0
604 #define DISPPLANE_GAMMA_ENABLE (1 << 30)
605 #define DISPPLANE_GAMMA_DISABLE 0
606 #define DISPPLANE_PIXFORMAT_MASK (0xf << 26)
607 #define DISPPLANE_8BPP (0x2 << 26)
608 #define DISPPLANE_15_16BPP (0x4 << 26)
609 #define DISPPLANE_16BPP (0x5 << 26)
610 #define DISPPLANE_32BPP_NO_ALPHA (0x6 << 26)
611 #define DISPPLANE_32BPP (0x7 << 26)
612 #define DISPPLANE_STEREO_ENABLE (1 << 25)
613 #define DISPPLANE_STEREO_DISABLE 0
614 #define DISPPLANE_SEL_PIPE_MASK (1 << 24)
615 #define DISPPLANE_SEL_PIPE_POS 24
616 #define DISPPLANE_SEL_PIPE_A 0
617 #define DISPPLANE_SEL_PIPE_B (1 << 24)
618 #define DISPPLANE_SRC_KEY_ENABLE (1 << 22)
619 #define DISPPLANE_SRC_KEY_DISABLE 0
620 #define DISPPLANE_LINE_DOUBLE (1 << 20)
621 #define DISPPLANE_NO_LINE_DOUBLE 0
622 #define DISPPLANE_STEREO_POLARITY_FIRST 0
623 #define DISPPLANE_STEREO_POLARITY_SECOND (1 << 18)
625 #define DISPPLANE_ALPHA_TRANS_ENABLE (1 << 15)
626 #define DISPPLANE_ALPHA_TRANS_DISABLE 0
627 #define DISPPLANE_SPRITE_ABOVE_DISPLAYA 0
628 #define DISPPLANE_SPRITE_ABOVE_OVERLAY (1)
629 #define DISPPLANE_BOTTOM (4)
631 #define DSPABASE 0x70184
632 #define DSPALINOFF 0x70184
633 #define DSPASTRIDE 0x70188
635 #define DSPBBASE 0x71184
636 #define DSPBLINOFF 0X71184
637 #define DSPBADDR DSPBBASE
638 #define DSPBSTRIDE 0x71188
640 #define DSPCBASE 0x72184
641 #define DSPCLINOFF 0x72184
642 #define DSPCSTRIDE 0x72188
644 #define DSPAKEYVAL 0x70194
645 #define DSPAKEYMASK 0x70198
647 #define DSPAPOS 0x7018C /* reserved */
648 #define DSPASIZE 0x70190
649 #define DSPBPOS 0x7118C
650 #define DSPBSIZE 0x71190
651 #define DSPCPOS 0x7218C
652 #define DSPCSIZE 0x72190
654 #define DSPASURF 0x7019C
655 #define DSPATILEOFF 0x701A4
657 #define DSPBSURF 0x7119C
658 #define DSPBTILEOFF 0x711A4
660 #define DSPCSURF 0x7219C
661 #define DSPCTILEOFF 0x721A4
662 #define DSPCKEYMAXVAL 0x721A0
663 #define DSPCKEYMINVAL 0x72194
664 #define DSPCKEYMSK 0x72198
666 #define VGACNTRL 0x71400
667 #define VGA_DISP_DISABLE (1 << 31)
668 #define VGA_2X_MODE (1 << 30)
669 #define VGA_PIPE_B_SELECT (1 << 29)
674 #define OV_C_OFFSET 0x08000
675 #define OV_OVADD 0x30000
676 #define OV_DOVASTA 0x30008
677 # define OV_PIPE_SELECT ((1 << 6)|(1 << 7))
678 # define OV_PIPE_SELECT_POS 6
681 #define OV_OGAMC5 0x30010
682 #define OV_OGAMC4 0x30014
683 #define OV_OGAMC3 0x30018
684 #define OV_OGAMC2 0x3001C
685 #define OV_OGAMC1 0x30020
686 #define OV_OGAMC0 0x30024
687 #define OVC_OVADD 0x38000
688 #define OVC_DOVCSTA 0x38008
689 #define OVC_OGAMC5 0x38010
690 #define OVC_OGAMC4 0x38014
691 #define OVC_OGAMC3 0x38018
692 #define OVC_OGAMC2 0x3801C
693 #define OVC_OGAMC1 0x38020
694 #define OVC_OGAMC0 0x38024
697 * Some BIOS scratch area registers. The 845 (and 830?) store the amount
698 * of video memory available to the BIOS in SWF1.
709 * 855 scratch registers.
711 #define SWF00 0x70410
712 #define SWF01 0x70414
713 #define SWF02 0x70418
714 #define SWF03 0x7041c
715 #define SWF04 0x70420
716 #define SWF05 0x70424
717 #define SWF06 0x70428
727 #define SWF30 0x72414
728 #define SWF31 0x72418
729 #define SWF32 0x7241c
735 #define PALETTE_A 0x0a000
736 #define PALETTE_B 0x0a800
737 #define PALETTE_C 0x0ac00
739 /* Cursor A & B regs */
740 #define CURACNTR 0x70080
741 #define CURSOR_MODE_DISABLE 0x00
742 #define CURSOR_MODE_64_32B_AX 0x07
743 #define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX)
744 #define MCURSOR_GAMMA_ENABLE (1 << 26)
745 #define CURABASE 0x70084
746 #define CURAPOS 0x70088
747 #define CURSOR_POS_MASK 0x007FF
748 #define CURSOR_POS_SIGN 0x8000
749 #define CURSOR_X_SHIFT 0
750 #define CURSOR_Y_SHIFT 16
751 #define CURBCNTR 0x700c0
752 #define CURBBASE 0x700c4
753 #define CURBPOS 0x700c8
754 #define CURCCNTR 0x700e0
755 #define CURCBASE 0x700e4
756 #define CURCPOS 0x700e8
759 * Interrupt Registers
767 * MOORESTOWN delta registers
769 #define MRST_DPLL_A 0x0f014
770 #define MDFLD_DPLL_B 0x0f018
771 #define MDFLD_INPUT_REF_SEL (1 << 14)
772 #define MDFLD_VCO_SEL (1 << 16)
773 #define DPLLA_MODE_LVDS (2 << 26) /* mrst */
774 #define MDFLD_PLL_LATCHEN (1 << 28)
775 #define MDFLD_PWR_GATE_EN (1 << 30)
776 #define MDFLD_P1_MASK (0x1FF << 17)
777 #define MRST_FPA0 0x0f040
778 #define MRST_FPA1 0x0f044
779 #define MDFLD_DPLL_DIV0 0x0f048
780 #define MDFLD_DPLL_DIV1 0x0f04c
781 #define MRST_PERF_MODE 0x020f4
784 * MEDFIELD HDMI registers
786 #define HDMIPHYMISCCTL 0x61134
787 #define HDMI_PHY_POWER_DOWN 0x7f
788 #define HDMIB_CONTROL 0x61140
789 #define HDMIB_PORT_EN (1 << 31)
790 #define HDMIB_PIPE_B_SELECT (1 << 30)
791 #define HDMIB_NULL_PACKET (1 << 9)
792 #define HDMIB_HDCP_PORT (1 << 5)
794 /* #define LVDS 0x61180 */
795 #define MRST_PANEL_8TO6_DITHER_ENABLE (1 << 25)
796 #define MRST_PANEL_24_DOT_1_FORMAT (1 << 24)
797 #define LVDS_A3_POWER_UP_0_OUTPUT (1 << 6)
800 #define MIPI_C 0x62190
801 #define MIPI_PORT_EN (1 << 31)
802 /* Turns on border drawing to allow centered display. */
803 #define SEL_FLOPPED_HSTX (1 << 23)
804 #define PASS_FROM_SPHY_TO_AFE (1 << 16)
805 #define MIPI_BORDER_EN (1 << 15)
806 #define MIPIA_3LANE_MIPIC_1LANE 0x1
807 #define MIPIA_2LANE_MIPIC_2LANE 0x2
808 #define TE_TRIGGER_DSI_PROTOCOL (1 << 2)
809 #define TE_TRIGGER_GPIO_PIN (1 << 3)
810 #define MIPI_TE_COUNT 0x61194
812 /* #define PP_CONTROL 0x61204 */
813 #define POWER_DOWN_ON_RESET (1 << 1)
815 /* #define PFIT_CONTROL 0x61230 */
816 #define PFIT_PIPE_SELECT (3 << 29)
817 #define PFIT_PIPE_SELECT_SHIFT (29)
819 /* #define BLC_PWM_CTL 0x61254 */
820 #define MRST_BACKLIGHT_MODULATION_FREQ_SHIFT (16)
821 #define MRST_BACKLIGHT_MODULATION_FREQ_MASK (0xffff << 16)
823 /* #define PIPEACONF 0x70008 */
824 #define PIPEACONF_PIPE_STATE (1 << 30)
825 /* #define DSPACNTR 0x70180 */
827 #define MRST_DSPABASE 0x7019c
828 #define MRST_DSPBBASE 0x7119c
829 #define MDFLD_DSPCBASE 0x7219c
832 * Moorestown registers.
838 #define MIPIC_REG_OFFSET 0x800
840 #define DEVICE_READY_REG 0xb000
841 #define LP_OUTPUT_HOLD (1 << 16)
842 #define EXIT_ULPS_DEV_READY 0x3
843 #define LP_OUTPUT_HOLD_RELEASE 0x810000
844 # define ENTERING_ULPS (2 << 1)
845 # define EXITING_ULPS (1 << 1)
846 # define ULPS_MASK (3 << 1)
847 # define BUS_POSSESSION (1 << 3)
848 #define INTR_STAT_REG 0xb004
849 #define RX_SOT_ERROR (1 << 0)
850 #define RX_SOT_SYNC_ERROR (1 << 1)
851 #define RX_ESCAPE_MODE_ENTRY_ERROR (1 << 3)
852 #define RX_LP_TX_SYNC_ERROR (1 << 4)
853 #define RX_HS_RECEIVE_TIMEOUT_ERROR (1 << 5)
854 #define RX_FALSE_CONTROL_ERROR (1 << 6)
855 #define RX_ECC_SINGLE_BIT_ERROR (1 << 7)
856 #define RX_ECC_MULTI_BIT_ERROR (1 << 8)
857 #define RX_CHECKSUM_ERROR (1 << 9)
858 #define RX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 10)
859 #define RX_DSI_VC_ID_INVALID (1 << 11)
860 #define TX_FALSE_CONTROL_ERROR (1 << 12)
861 #define TX_ECC_SINGLE_BIT_ERROR (1 << 13)
862 #define TX_ECC_MULTI_BIT_ERROR (1 << 14)
863 #define TX_CHECKSUM_ERROR (1 << 15)
864 #define TX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 16)
865 #define TX_DSI_VC_ID_INVALID (1 << 17)
866 #define HIGH_CONTENTION (1 << 18)
867 #define LOW_CONTENTION (1 << 19)
868 #define DPI_FIFO_UNDER_RUN (1 << 20)
869 #define HS_TX_TIMEOUT (1 << 21)
870 #define LP_RX_TIMEOUT (1 << 22)
871 #define TURN_AROUND_ACK_TIMEOUT (1 << 23)
872 #define ACK_WITH_NO_ERROR (1 << 24)
873 #define HS_GENERIC_WR_FIFO_FULL (1 << 27)
874 #define LP_GENERIC_WR_FIFO_FULL (1 << 28)
875 #define SPL_PKT_SENT (1 << 30)
876 #define INTR_EN_REG 0xb008
877 #define DSI_FUNC_PRG_REG 0xb00c
878 #define DPI_CHANNEL_NUMBER_POS 0x03
879 #define DBI_CHANNEL_NUMBER_POS 0x05
880 #define FMT_DPI_POS 0x07
881 #define FMT_DBI_POS 0x0A
882 #define DBI_DATA_WIDTH_POS 0x0D
884 /* DPI PIXEL FORMATS */
885 #define RGB_565_FMT 0x01 /* RGB 565 FORMAT */
886 #define RGB_666_FMT 0x02 /* RGB 666 FORMAT */
887 #define LRGB_666_FMT 0x03 /* RGB LOOSELY PACKED
890 #define RGB_888_FMT 0x04 /* RGB 888 FORMAT */
891 #define VIRTUAL_CHANNEL_NUMBER_0 0x00 /* Virtual channel 0 */
892 #define VIRTUAL_CHANNEL_NUMBER_1 0x01 /* Virtual channel 1 */
893 #define VIRTUAL_CHANNEL_NUMBER_2 0x02 /* Virtual channel 2 */
894 #define VIRTUAL_CHANNEL_NUMBER_3 0x03 /* Virtual channel 3 */
896 #define DBI_NOT_SUPPORTED 0x00 /* command mode
899 #define DBI_DATA_WIDTH_16BIT 0x01 /* 16 bit data */
900 #define DBI_DATA_WIDTH_9BIT 0x02 /* 9 bit data */
901 #define DBI_DATA_WIDTH_8BIT 0x03 /* 8 bit data */
902 #define DBI_DATA_WIDTH_OPT1 0x04 /* option 1 */
903 #define DBI_DATA_WIDTH_OPT2 0x05 /* option 2 */
905 #define HS_TX_TIMEOUT_REG 0xb010
906 #define LP_RX_TIMEOUT_REG 0xb014
907 #define TURN_AROUND_TIMEOUT_REG 0xb018
908 #define DEVICE_RESET_REG 0xb01C
909 #define DPI_RESOLUTION_REG 0xb020
910 #define RES_V_POS 0x10
911 #define DBI_RESOLUTION_REG 0xb024 /* Reserved for MDFLD */
912 #define HORIZ_SYNC_PAD_COUNT_REG 0xb028
913 #define HORIZ_BACK_PORCH_COUNT_REG 0xb02C
914 #define HORIZ_FRONT_PORCH_COUNT_REG 0xb030
915 #define HORIZ_ACTIVE_AREA_COUNT_REG 0xb034
916 #define VERT_SYNC_PAD_COUNT_REG 0xb038
917 #define VERT_BACK_PORCH_COUNT_REG 0xb03c
918 #define VERT_FRONT_PORCH_COUNT_REG 0xb040
919 #define HIGH_LOW_SWITCH_COUNT_REG 0xb044
920 #define DPI_CONTROL_REG 0xb048
921 #define DPI_SHUT_DOWN (1 << 0)
922 #define DPI_TURN_ON (1 << 1)
923 #define DPI_COLOR_MODE_ON (1 << 2)
924 #define DPI_COLOR_MODE_OFF (1 << 3)
925 #define DPI_BACK_LIGHT_ON (1 << 4)
926 #define DPI_BACK_LIGHT_OFF (1 << 5)
927 #define DPI_LP (1 << 6)
928 #define DPI_DATA_REG 0xb04c
929 #define DPI_BACK_LIGHT_ON_DATA 0x07
930 #define DPI_BACK_LIGHT_OFF_DATA 0x17
931 #define INIT_COUNT_REG 0xb050
932 #define MAX_RET_PAK_REG 0xb054
933 #define VIDEO_FMT_REG 0xb058
934 #define COMPLETE_LAST_PCKT (1 << 2)
935 #define EOT_DISABLE_REG 0xb05c
936 #define ENABLE_CLOCK_STOPPING (1 << 1)
937 #define LP_BYTECLK_REG 0xb060
938 #define LP_GEN_DATA_REG 0xb064
939 #define HS_GEN_DATA_REG 0xb068
940 #define LP_GEN_CTRL_REG 0xb06C
941 #define HS_GEN_CTRL_REG 0xb070
942 #define DCS_CHANNEL_NUMBER_POS 0x6
943 #define MCS_COMMANDS_POS 0x8
944 #define WORD_COUNTS_POS 0x8
945 #define MCS_PARAMETER_POS 0x10
946 #define GEN_FIFO_STAT_REG 0xb074
947 #define HS_DATA_FIFO_FULL (1 << 0)
948 #define HS_DATA_FIFO_HALF_EMPTY (1 << 1)
949 #define HS_DATA_FIFO_EMPTY (1 << 2)
950 #define LP_DATA_FIFO_FULL (1 << 8)
951 #define LP_DATA_FIFO_HALF_EMPTY (1 << 9)
952 #define LP_DATA_FIFO_EMPTY (1 << 10)
953 #define HS_CTRL_FIFO_FULL (1 << 16)
954 #define HS_CTRL_FIFO_HALF_EMPTY (1 << 17)
955 #define HS_CTRL_FIFO_EMPTY (1 << 18)
956 #define LP_CTRL_FIFO_FULL (1 << 24)
957 #define LP_CTRL_FIFO_HALF_EMPTY (1 << 25)
958 #define LP_CTRL_FIFO_EMPTY (1 << 26)
959 #define DBI_FIFO_EMPTY (1 << 27)
960 #define DPI_FIFO_EMPTY (1 << 28)
961 #define HS_LS_DBI_ENABLE_REG 0xb078
962 #define TXCLKESC_REG 0xb07c
963 #define DPHY_PARAM_REG 0xb080
964 #define DBI_BW_CTRL_REG 0xb084
965 #define CLK_LANE_SWT_REG 0xb088
968 * MIPI Adapter registers
970 #define MIPI_CONTROL_REG 0xb104
971 #define MIPI_2X_CLOCK_BITS ((1 << 0) | (1 << 1))
972 #define MIPI_DATA_ADDRESS_REG 0xb108
973 #define MIPI_DATA_LENGTH_REG 0xb10C
974 #define MIPI_COMMAND_ADDRESS_REG 0xb110
975 #define MIPI_COMMAND_LENGTH_REG 0xb114
976 #define MIPI_READ_DATA_RETURN_REG0 0xb118
977 #define MIPI_READ_DATA_RETURN_REG1 0xb11C
978 #define MIPI_READ_DATA_RETURN_REG2 0xb120
979 #define MIPI_READ_DATA_RETURN_REG3 0xb124
980 #define MIPI_READ_DATA_RETURN_REG4 0xb128
981 #define MIPI_READ_DATA_RETURN_REG5 0xb12C
982 #define MIPI_READ_DATA_RETURN_REG6 0xb130
983 #define MIPI_READ_DATA_RETURN_REG7 0xb134
984 #define MIPI_READ_DATA_VALID_REG 0xb138
987 #define soft_reset 0x01
989 * The display module performs a software reset.
990 * Registers are written with their SW Reset default values.
992 #define get_power_mode 0x0a
994 * The display module returns the current power mode
996 #define get_address_mode 0x0b
998 * The display module returns the current status.
1000 #define get_pixel_format 0x0c
1002 * This command gets the pixel format for the RGB image data
1003 * used by the interface.
1005 #define get_display_mode 0x0d
1007 * The display module returns the Display Image Mode status.
1009 #define get_signal_mode 0x0e
1011 * The display module returns the Display Signal Mode.
1013 #define get_diagnostic_result 0x0f
1015 * The display module returns the self-diagnostic results following
1016 * a Sleep Out command.
1018 #define enter_sleep_mode 0x10
1020 * This command causes the display module to enter the Sleep mode.
1021 * In this mode, all unnecessary blocks inside the display module are
1022 * disabled except interface communication. This is the lowest power
1023 * mode the display module supports.
1025 #define exit_sleep_mode 0x11
1027 * This command causes the display module to exit Sleep mode.
1028 * All blocks inside the display module are enabled.
1030 #define enter_partial_mode 0x12
1032 * This command causes the display module to enter the Partial Display
1033 * Mode. The Partial Display Mode window is described by the
1034 * set_partial_area command.
1036 #define enter_normal_mode 0x13
1038 * This command causes the display module to enter the Normal mode.
1039 * Normal Mode is defined as Partial Display mode and Scroll mode are off
1041 #define exit_invert_mode 0x20
1043 * This command causes the display module to stop inverting the image
1044 * data on the display device. The frame memory contents remain unchanged.
1045 * No status bits are changed.
1047 #define enter_invert_mode 0x21
1049 * This command causes the display module to invert the image data only on
1050 * the display device. The frame memory contents remain unchanged.
1051 * No status bits are changed.
1053 #define set_gamma_curve 0x26
1055 * This command selects the desired gamma curve for the display device.
1056 * Four fixed gamma curves are defined in section DCS spec.
1058 #define set_display_off 0x28
1059 /* ************************************************************************* *\
1060 This command causes the display module to stop displaying the image data
1061 on the display device. The frame memory contents remain unchanged.
1062 No status bits are changed.
1063 \* ************************************************************************* */
1064 #define set_display_on 0x29
1065 /* ************************************************************************* *\
1066 This command causes the display module to start displaying the image data
1067 on the display device. The frame memory contents remain unchanged.
1068 No status bits are changed.
1069 \* ************************************************************************* */
1070 #define set_column_address 0x2a
1072 * This command defines the column extent of the frame memory accessed by
1073 * the hostprocessor with the read_memory_continue and
1074 * write_memory_continue commands.
1075 * No status bits are changed.
1077 #define set_page_addr 0x2b
1079 * This command defines the page extent of the frame memory accessed by
1080 * the host processor with the write_memory_continue and
1081 * read_memory_continue command.
1082 * No status bits are changed.
1084 #define write_mem_start 0x2c
1086 * This command transfers image data from the host processor to the
1087 * display modules frame memory starting at the pixel location specified
1088 * by preceding set_column_address and set_page_address commands.
1090 #define set_partial_area 0x30
1092 * This command defines the Partial Display mode s display area.
1093 * There are two parameters associated with this command, the first
1094 * defines the Start Row (SR) and the second the End Row (ER). SR and ER
1095 * refer to the Frame Memory Line Pointer.
1097 #define set_scroll_area 0x33
1099 * This command defines the display modules Vertical Scrolling Area.
1101 #define set_tear_off 0x34
1103 * This command turns off the display modules Tearing Effect output
1104 * signal on the TE signal line.
1106 #define set_tear_on 0x35
1108 * This command turns on the display modules Tearing Effect output signal
1109 * on the TE signal line.
1111 #define set_address_mode 0x36
1113 * This command sets the data order for transfers from the host processor
1114 * to display modules frame memory,bits B[7:5] and B3, and from the
1115 * display modules frame memory to the display device, bits B[2:0] and B4.
1117 #define set_scroll_start 0x37
1119 * This command sets the start of the vertical scrolling area in the frame
1120 * memory. The vertical scrolling area is fully defined when this command
1121 * is used with the set_scroll_area command The set_scroll_start command
1122 * has one parameter, the Vertical Scroll Pointer. The VSP defines the
1123 * line in the frame memory that is written to the display device as the
1124 * first line of the vertical scroll area.
1126 #define exit_idle_mode 0x38
1128 * This command causes the display module to exit Idle mode.
1130 #define enter_idle_mode 0x39
1132 * This command causes the display module to enter Idle Mode.
1133 * In Idle Mode, color expression is reduced. Colors are shown on the
1134 * display device using the MSB of each of the R, G and B color
1135 * components in the frame memory
1137 #define set_pixel_format 0x3a
1139 * This command sets the pixel format for the RGB image data used by the
1141 * Bits D[6:4] DPI Pixel Format Definition
1142 * Bits D[2:0] DBI Pixel Format Definition
1143 * Bits D7 and D3 are not used.
1145 #define DCS_PIXEL_FORMAT_3bpp 0x1
1146 #define DCS_PIXEL_FORMAT_8bpp 0x2
1147 #define DCS_PIXEL_FORMAT_12bpp 0x3
1148 #define DCS_PIXEL_FORMAT_16bpp 0x5
1149 #define DCS_PIXEL_FORMAT_18bpp 0x6
1150 #define DCS_PIXEL_FORMAT_24bpp 0x7
1152 #define write_mem_cont 0x3c
1155 * This command transfers image data from the host processor to the
1156 * display module's frame memory continuing from the pixel location
1157 * following the previous write_memory_continue or write_memory_start
1160 #define set_tear_scanline 0x44
1162 * This command turns on the display modules Tearing Effect output signal
1163 * on the TE signal line when the display module reaches line N.
1165 #define get_scanline 0x45
1167 * The display module returns the current scanline, N, used to update the
1168 * display device. The total number of scanlines on a display device is
1169 * defined as VSYNC + VBP + VACT + VFP.The first scanline is defined as
1170 * the first line of V Sync and is denoted as Line 0.
1171 * When in Sleep Mode, the value returned by get_scanline is undefined.
1174 /* MCS or Generic COMMANDS */
1175 /* MCS/generic data type */
1176 #define GEN_SHORT_WRITE_0 0x03 /* generic short write, no parameters */
1177 #define GEN_SHORT_WRITE_1 0x13 /* generic short write, 1 parameters */
1178 #define GEN_SHORT_WRITE_2 0x23 /* generic short write, 2 parameters */
1179 #define GEN_READ_0 0x04 /* generic read, no parameters */
1180 #define GEN_READ_1 0x14 /* generic read, 1 parameters */
1181 #define GEN_READ_2 0x24 /* generic read, 2 parameters */
1182 #define GEN_LONG_WRITE 0x29 /* generic long write */
1183 #define MCS_SHORT_WRITE_0 0x05 /* MCS short write, no parameters */
1184 #define MCS_SHORT_WRITE_1 0x15 /* MCS short write, 1 parameters */
1185 #define MCS_READ 0x06 /* MCS read, no parameters */
1186 #define MCS_LONG_WRITE 0x39 /* MCS long write */
1187 /* MCS/generic commands */
1189 #define write_display_profile 0x50
1190 #define write_display_brightness 0x51
1191 #define write_ctrl_display 0x53
1192 #define write_ctrl_cabc 0x55
1193 #define UI_IMAGE 0x01
1194 #define STILL_IMAGE 0x02
1195 #define MOVING_IMAGE 0x03
1196 #define write_hysteresis 0x57
1197 #define write_gamma_setting 0x58
1198 #define write_cabc_min_bright 0x5e
1199 #define write_kbbc_profile 0x60
1201 #define tmd_write_display_brightness 0x8c
1204 * This command is used to control ambient light, panel backlight
1205 * brightness and gamma settings.
1207 #define BRIGHT_CNTL_BLOCK_ON (1 << 5)
1208 #define AMBIENT_LIGHT_SENSE_ON (1 << 4)
1209 #define DISPLAY_DIMMING_ON (1 << 3)
1210 #define BACKLIGHT_ON (1 << 2)
1211 #define DISPLAY_BRIGHTNESS_AUTO (1 << 1)
1212 #define GAMMA_AUTO (1 << 0)
1214 /* DCS Interface Pixel Formats */
1215 #define DCS_PIXEL_FORMAT_3BPP 0x1
1216 #define DCS_PIXEL_FORMAT_8BPP 0x2
1217 #define DCS_PIXEL_FORMAT_12BPP 0x3
1218 #define DCS_PIXEL_FORMAT_16BPP 0x5
1219 #define DCS_PIXEL_FORMAT_18BPP 0x6
1220 #define DCS_PIXEL_FORMAT_24BPP 0x7
1221 /* ONE PARAMETER READ DATA */
1222 #define addr_mode_data 0xfc
1223 #define diag_res_data 0x00
1224 #define disp_mode_data 0x23
1225 #define pxl_fmt_data 0x77
1226 #define pwr_mode_data 0x74
1227 #define sig_mode_data 0x00
1228 /* TWO PARAMETERS READ DATA */
1229 #define scanline_data1 0xff
1230 #define scanline_data2 0xff
1231 #define NON_BURST_MODE_SYNC_PULSE 0x01 /* Non Burst Mode
1234 #define NON_BURST_MODE_SYNC_EVENTS 0x02 /* Non Burst Mode
1237 #define BURST_MODE 0x03 /* Burst Mode */
1238 #define DBI_COMMAND_BUFFER_SIZE 0x240 /* 0x32 */ /* 0x120 */
1239 /* Allocate at least
1240 * 0x100 Byte with 32
1243 #define DBI_DATA_BUFFER_SIZE 0x120 /* Allocate at least
1244 * 0x100 Byte with 32
1247 #define DBI_CB_TIME_OUT 0xFFFF
1249 #define GEN_FB_TIME_OUT 2000
1252 #define SKU_100 0x02
1253 #define SKU_100L 0x04
1254 #define SKU_BYPASS 0x08
1256 /* Some handy macros for playing with bitfields. */
1257 #define PSB_MASK(high, low) (((1<<((high)-(low)+1))-1)<<(low))
1258 #define SET_FIELD(value, field) (((value) << field ## _SHIFT) & field ## _MASK)
1259 #define GET_FIELD(word, field) (((word) & field ## _MASK) >> field ## _SHIFT)
1261 #define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a)))
1263 /* PCI config space */
1265 #define SB_PCKT 0x02100 /* cedarview */
1266 # define SB_OPCODE_MASK PSB_MASK(31, 16)
1267 # define SB_OPCODE_SHIFT 16
1268 # define SB_OPCODE_READ 0
1269 # define SB_OPCODE_WRITE 1
1270 # define SB_DEST_MASK PSB_MASK(15, 8)
1271 # define SB_DEST_SHIFT 8
1272 # define SB_DEST_DPLL 0x88
1273 # define SB_BYTE_ENABLE_MASK PSB_MASK(7, 4)
1274 # define SB_BYTE_ENABLE_SHIFT 4
1275 # define SB_BUSY (1 << 0)
1277 #define DSPCLK_GATE_D 0x6200
1278 # define VRHUNIT_CLOCK_GATE_DISABLE (1 << 28) /* Fixed value on CDV */
1279 # define DPOUNIT_CLOCK_GATE_DISABLE (1 << 11)
1280 # define DPIOUNIT_CLOCK_GATE_DISABLE (1 << 6)
1282 #define RAMCLK_GATE_D 0x6210
1284 /* 32-bit value read/written from the DPIO reg. */
1285 #define SB_DATA 0x02104 /* cedarview */
1286 /* 32-bit address of the DPIO reg to be read/written. */
1287 #define SB_ADDR 0x02108 /* cedarview */
1288 #define DPIO_CFG 0x02110 /* cedarview */
1289 # define DPIO_MODE_SELECT_1 (1 << 3)
1290 # define DPIO_MODE_SELECT_0 (1 << 2)
1291 # define DPIO_SFR_BYPASS (1 << 1)
1292 /* reset is active low */
1293 # define DPIO_CMN_RESET_N (1 << 0)
1295 /* Cedarview sideband registers */
1296 #define _SB_M_A 0x8008
1297 #define _SB_M_B 0x8028
1298 #define SB_M(pipe) _PIPE(pipe, _SB_M_A, _SB_M_B)
1299 # define SB_M_DIVIDER_MASK (0xFF << 24)
1300 # define SB_M_DIVIDER_SHIFT 24
1302 #define _SB_N_VCO_A 0x8014
1303 #define _SB_N_VCO_B 0x8034
1304 #define SB_N_VCO(pipe) _PIPE(pipe, _SB_N_VCO_A, _SB_N_VCO_B)
1305 #define SB_N_VCO_SEL_MASK PSB_MASK(31, 30)
1306 #define SB_N_VCO_SEL_SHIFT 30
1307 #define SB_N_DIVIDER_MASK PSB_MASK(29, 26)
1308 #define SB_N_DIVIDER_SHIFT 26
1309 #define SB_N_CB_TUNE_MASK PSB_MASK(25, 24)
1310 #define SB_N_CB_TUNE_SHIFT 24
1312 /* the bit 14:13 is used to select between the different reference clock for Pipe A/B */
1313 #define SB_REF_DPLLA 0x8010
1314 #define SB_REF_DPLLB 0x8030
1315 #define REF_CLK_MASK (0x3 << 13)
1316 #define REF_CLK_CORE (0 << 13)
1317 #define REF_CLK_DPLL (1 << 13)
1318 #define REF_CLK_DPLLA (2 << 13)
1319 /* For the DPLL B, it will use the reference clk from DPLL A when using (2 << 13) */
1321 #define _SB_REF_A 0x8018
1322 #define _SB_REF_B 0x8038
1323 #define SB_REF_SFR(pipe) _PIPE(pipe, _SB_REF_A, _SB_REF_B)
1325 #define _SB_P_A 0x801c
1326 #define _SB_P_B 0x803c
1327 #define SB_P(pipe) _PIPE(pipe, _SB_P_A, _SB_P_B)
1328 #define SB_P2_DIVIDER_MASK PSB_MASK(31, 30)
1329 #define SB_P2_DIVIDER_SHIFT 30
1330 #define SB_P2_10 0 /* HDMI, DP, DAC */
1331 #define SB_P2_5 1 /* DAC */
1332 #define SB_P2_14 2 /* LVDS single */
1333 #define SB_P2_7 3 /* LVDS double */
1334 #define SB_P1_DIVIDER_MASK PSB_MASK(15, 12)
1335 #define SB_P1_DIVIDER_SHIFT 12
1337 #define PSB_LANE0 0x120
1338 #define PSB_LANE1 0x220
1339 #define PSB_LANE2 0x2320
1340 #define PSB_LANE3 0x2420
1342 #define LANE_PLL_MASK (0x7 << 20)
1343 #define LANE_PLL_ENABLE (0x3 << 20)
1344 #define LANE_PLL_PIPE(p) (((p) == 0) ? (1 << 21) : (0 << 21))