3 #include <dt-bindings/interrupt-controller/arm-gic.h>
4 #include <dt-bindings/rkfb/rk_fb.h>
6 #include "../../../arm/boot/dts/lcd-ld089wu1-mipi.dtsi"
9 bootargs = "earlyprintk=uart8250-32bit,0xff690000 clk_ignore_unused";
13 compatible = "wlan-platdata";
15 rockchip,grf = <&grf>;
17 /* wifi_chip_type - wifi chip define
18 * bcmwifi ==> like ap6xxx, rk90x;
19 * rtkwifi ==> like rtl8188xx, rtl8723xx;
20 * esp8089 ==> esp8089;
21 * other ==> for other wifi;
23 wifi_chip_type = "bcmwifi";
25 sdio_vref = <1800>; //1800mv or 3300mv
26 power_pmu_regulator = "rk818_ldo8_reg";
27 power_pmu_enable_level = <1>; //1->HIGH, 0->LOW
28 vref_pmu_regulator = "rk818_ldo8_reg";
29 vref_pmu_enable_level = <1>; //1->HIGH, 0->LOW
31 WIFI,poweren_gpio = <&gpio3 GPIO_A4 GPIO_ACTIVE_HIGH>;
32 WIFI,host_wake_irq = <&gpio3 GPIO_A6 GPIO_ACTIVE_HIGH>;
38 compatible = "bluetooth-platdata";
39 uart_rts_gpios = <&gpio2 GPIO_D3 GPIO_ACTIVE_LOW>;
40 pinctrl-names = "default","rts_gpio";
41 pinctrl-0 = <&uart0_rts>;
42 pinctrl-1 = <&uart0_rts_gpio>;
44 BT,power_gpio = <&gpio3 GPIO_A3 GPIO_ACTIVE_HIGH>;
45 BT,reset_gpio = <&gpio3 GPIO_A5 GPIO_ACTIVE_HIGH>;
46 BT,wake_gpio = <&gpio3 GPIO_A2 GPIO_ACTIVE_HIGH>;
47 BT,wake_host_irq = <&gpio3 GPIO_A7 GPIO_ACTIVE_HIGH>;
53 compatible = "hall_och165t";
54 type = <SENSOR_TYPE_HALL>;
55 irq-gpio = <&gpio0 GPIO_C0 IRQ_TYPE_EDGE_BOTH>;
59 compatible = "pwm-backlight";
60 pwms = <&pwm0 0 25000>;
61 brightness-levels = <255 254 253 252 251 250 249 248 247 246 245 244 243 242 241 240
62 239 238 237 236 235 234 233 232 231 230 229 228 227 226 225 224 223 222 221 220
63 219 218 217 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200
64 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180
65 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160
66 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140
67 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120
68 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100
69 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70
70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40
71 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
73 default-brightness-level = <200>;
74 enable-gpios = <&gpio0 GPIO_C4 GPIO_ACTIVE_HIGH>;
78 compatible = "rockchip_pwm_regulator";
79 pwms = <&pwm1 0 2000>;
81 rockchip,pwm_voltage_map= <925000 950000 975000 1000000 1025000 1050000 1075000 1100000 1125000 1150000 1175000 1200000 1225000 1250000 1275000 1300000 1325000 1350000 1375000 1400000>;
82 rockchip,pwm_voltage= <1000000>;
83 rockchip,pwm_min_voltage= <925000>;
84 rockchip,pwm_max_voltage= <1400000>;
85 rockchip,pwm_suspend_voltage= <950000>;
86 rockchip,pwm_coefficient= <475>;
90 pwm_reg0: regulator@0 {
91 regulator-compatible = "pwm_dcdc1";
92 regulator-name= "vdd_logic";
93 regulator-min-microvolt = <925000>;
94 regulator-max-microvolt = <1400000>;
101 codec_hdmi_i2s: codec-hdmi-i2s {
102 compatible = "hdmi-i2s";
105 codec_hdmi_spdif: codec-hdmi-spdif {
106 compatible = "hdmi-spdif";
110 compatible = "rockchip-hdmi-i2s";
113 audio-codec = <&codec_hdmi_i2s>;
114 i2s-controller = <&i2s0>;
120 rockchip-hdmi-spdif {
121 compatible = "rockchip-hdmi-spdif";
124 audio-codec = <&codec_hdmi_spdif>;
125 i2s-controller = <&spdif>;
131 compatible = "rockchip-es8316";
134 audio-codec = <&es8316>;
135 i2s-controller = <&i2s0>;
142 compatible = "rockchip,rk3368-io-voltage-domain";
143 rockchip,grf = <&grf>;
144 rockchip,pmugrf = <&pmugrf>;
147 gpio30-supply = <&rk818_dcdc4_reg>; /*APIO1_VDD*/
148 wifi-supply = <&rk818_ldo8_reg>; /*APIO2_VDD*/
149 audio-supply = <&rk818_dcdc4_reg>; /*APIO3_VDD*/
150 gpio1830-supply = <&rk818_dcdc4_reg>; /*ADIO4_VDD*/
151 sdcard-supply = <&rk818_ldo9_reg>; /*SDMMC_VDD*/
154 pmu-supply = <&rk818_ldo5_reg>; /*PMUIO_VDD*/
155 vop-supply = <&rk818_ldo5_reg>; /*LCDC_VDD*/
160 //used for init some gpio
161 init-gpios = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH>;
165 rockchip,pins = <0 GPIO_C7 RK_FUNC_GPIO &pcfg_pull_down>;
168 rockchip,pins = <0 GPIO_A3 RK_FUNC_3 &pcfg_pull_none>;
171 rockchip,pins = <0 GPIO_C2 RK_FUNC_GPIO &pcfg_pull_down>;
180 status = "disabled"; // used nand set "disabled" ,used emmc set "okay"
184 status = "okay"; // used nand set "disabled" ,used emmc set "okay"
188 clock-frequency = <100000000>;
189 clock-freq-min-max = <400000 100000000>;
196 //supports-DDR_MODE; //you should set the two value in your project. only close in RK3288-SDK board.
200 keep-power-in-suspend;
207 clock-frequency = <50000000>;
208 clock-freq-min-max = <400000 50000000>;
212 card-detect-delay = <200>;
215 keep-power-in-suspend;
217 vmmc-supply = <&rk818_ldo1_reg>;
222 clock-frequency = <50000000>;
223 clock-freq-min-max = <200000 50000000>;
227 keep-power-in-suspend;
250 dma-names = "!tx", "!rx";
251 pinctrl-0 = <&uart0_xfer &uart0_cts>;
257 compatible = "silergy,syr82x";
261 #address-cells = <1>;
263 syr827_dc1: regulator@0 {
265 regulator-compatible = "syr82x_dcdc1";
266 regulator-name = "vdd_arm";
267 regulator-min-microvolt = <712500>;
268 regulator-max-microvolt = <1500000>;
271 regulator-initial-mode = <0x2>;
272 regulator-initial-state = <3>;
273 regulator-state-mem {
274 regulator-state-mode = <0x2>;
275 regulator-state-disabled;
276 regulator-state-uv = <900000>;
282 compatible = "silergy,syr82x";
286 #address-cells = <1>;
288 syr828_dc1: regulator@0 {
290 regulator-compatible = "syr82x_dcdc1";
291 regulator-name = "vdd_gpu";
292 regulator-min-microvolt = <712500>;
293 regulator-max-microvolt = <1500000>;
296 regulator-initial-mode = <0x2>;
297 regulator-initial-state = <3>;
298 regulator-state-mem {
299 regulator-state-mode = <0x2>;
300 regulator-state-enabled;
301 regulator-state-uv = <900000>;
310 compatible = "rockchip,rk818";
312 ocv_table = <3300 3599 3671 3701 3728 3746 3762
313 3772 3781 3792 3816 3836 3866 3910
314 3942 3971 4002 4050 4088 4132 4183>;
315 design_capacity = <3914>;
316 design_qmax = <4000>;
317 max_overcharge = <100>;
318 max_charge_currentmA = <1500>;
319 max_charge_voltagemV = <4260>;
320 max_bat_voltagemV = <4200>;
321 sleep_enter_current = <150>;
322 sleep_exit_current = <180>;
330 compatible = "es8316";
339 compatible = "goodix,gt9xx";
341 touch-gpio = <&gpio0 GPIO_B4 IRQ_TYPE_LEVEL_LOW>;
342 reset-gpio = <&gpio0 GPIO_B3 GPIO_ACTIVE_HIGH>;
357 compatible = "mpu6050";
359 mpu-int_config = <0x10>;
360 mpu-level_shifter = <0>;
361 mpu-orientation = <0 1 0 1 0 0 0 0 1>;
365 irq-gpio = <&gpio3 GPIO_B6 IRQ_TYPE_LEVEL_LOW>;
371 compatible = "mpu_ak8963";
374 compass-adapt_num = <0>;
375 compass-orientation = <1 0 0 0 1 0 0 0 1>;
391 rockchip,disp-mode = <NO_DUAL>;
392 rockchip,uboot-logo-on = <0>;
397 display-timings = <&disp_timings>;
402 rockchip,mirror = <NO_MIRROR>;
403 rockchip,cabc_mode = <0>;
404 rockchip,fb-win-map = <FB_DEFAULT_ORDER>;
405 power_ctr: power_ctr {
406 rockchip,debug = <0>;
408 rockchip,power_type = <GPIO>;
409 gpios = <&gpio0 GPIO_C6 GPIO_ACTIVE_HIGH>;
410 rockchip,delay = <10>;
414 rockchip,power_type = <GPIO>;
415 gpios = <&gpio0 GPIO_C5 GPIO_ACTIVE_HIGH>;
416 rockchip,delay = <10>;
420 rockchip,power_type = <GPIO>;
421 gpios = <&gpio3 GPIO_D6 GPIO_ACTIVE_HIGH>;
422 rockchip,delay = <5>;
430 rockchips,hdmi_audio_source = <0>;
437 compatible = "rockchip_headset";
438 headset_gpio = <&gpio0 GPIO_C7 GPIO_ACTIVE_LOW>;
439 pinctrl-names = "default";
440 pinctrl-0 = <&gpio0_c7>;//gpio0_c7
441 io-channels = <&adc 2>;
444 hook_down_type = ; //interrupt hook key down status
449 compatible = "rockchip,key";
450 io-channels = <&adc 1>;
455 rockchip,adc_value = <1>;
460 label = "volume down";
461 rockchip,adc_value = <170>;
465 gpios = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
481 &clk_ddr_dvfs_table {
492 SYS_STATUS_NORMAL 400000
493 SYS_STATUS_SUSPEND 200000
494 SYS_STATUS_VIDEO_1080P 240000
495 SYS_STATUS_VIDEO_4K 400000
496 SYS_STATUS_PERFORMANCE 528000
497 SYS_STATUS_DUALVIEW 400000
498 SYS_STATUS_BOOST 324000
499 SYS_STATUS_ISP 400000
512 host_drv_gpio = <&gpio0 GPIO_A4 GPIO_ACTIVE_LOW>;
513 otg_drv_gpio = <&gpio0 GPIO_D1 GPIO_ACTIVE_LOW>;
514 rockchip,remote_wakeup;
515 rockchip,usb_irq_wakeup;
518 /include/ "../../../arm/boot/dts/rk818.dtsi"
520 gpios =<&gpio0 GPIO_A1 GPIO_ACTIVE_HIGH>,<&gpio0 GPIO_A0 GPIO_ACTIVE_LOW>;
521 rk818,system-power-controller;
525 rk818_dcdc1_reg: regulator@0{
526 regulator-name= "vdd_arm";/*vcc arm*/
527 regulator-min-microvolt = <700000>;/*<725000>;*/
528 regulator-max-microvolt = <1500000>;
529 regulator-initial-mode = <0x2>;
530 regulator-initial-state = <3>;
531 regulator-state-mem {
532 regulator-state-mode = <0x2>;
533 regulator-state-enabled;
534 regulator-state-uv =<900000>;
538 rk818_dcdc2_reg: regulator@1 {
539 regulator-name= "vdd_gpu";/*vcc gpu*/
540 regulator-min-microvolt = <700000>;
541 regulator-max-microvolt = <1200000>;
542 regulator-initial-mode = <0x2>;
543 regulator-initial-state = <3>;
544 regulator-state-mem {
545 regulator-state-mode = <0x2>;
546 regulator-state-enabled;
547 regulator-state-uv = <1200000>;
551 rk818_dcdc3_reg: regulator@2 {
552 regulator-name= "vcc_ddr";
553 regulator-min-microvolt = <1200000>;
554 regulator-max-microvolt = <1200000>;
555 regulator-initial-mode = <0x2>;
556 regulator-initial-state = <3>;
557 regulator-state-mem {
558 regulator-state-mode = <0x2>;
559 regulator-state-enabled;
560 regulator-state-uv = <1200000>;
564 rk818_dcdc4_reg: regulator@3 {
565 regulator-name= "vccio";
566 regulator-min-microvolt = <3000000>;
567 regulator-max-microvolt = <3000000>;
568 regulator-initial-mode = <0x2>;
569 regulator-initial-state = <3>;
570 regulator-state-mem {
571 regulator-state-mode = <0x2>;
572 regulator-state-enabled;
573 regulator-state-uv = <3000000>;
577 rk818_ldo1_reg: regulator@4 {
578 regulator-name= "vcc_codec";
579 regulator-min-microvolt = <3300000>;
580 regulator-max-microvolt = <3300000>;
581 regulator-initial-state = <3>;
582 regulator-state-mem {
583 regulator-state-enabled;
584 regulator-state-uv = <3300000>;
588 rk818_ldo2_reg: regulator@5 {
589 regulator-name= "vcc_tp";
590 regulator-min-microvolt = <3300000>;
591 regulator-max-microvolt = <3300000>;
592 regulator-initial-state = <3>;
593 regulator-state-mem {
594 regulator-state-enabled;
595 regulator-state-uv = <3300000>;
599 rk818_ldo3_reg: regulator@6 {
600 regulator-name= "vdd_10";
601 regulator-min-microvolt = <1000000>;
602 regulator-max-microvolt = <1000000>;
603 regulator-initial-state = <3>;
604 regulator-state-mem {
605 regulator-state-enabled;
606 regulator-state-uv = <1000000>;
610 rk818_ldo4_reg:regulator@7 {
611 regulator-name= "vcc18_lcd";
612 regulator-min-microvolt = <1800000>;
613 regulator-max-microvolt = <1800000>;
614 regulator-initial-state = <3>;
615 regulator-state-mem {
616 regulator-state-disabled;
617 regulator-state-uv = <1800000>;
621 rk818_ldo5_reg: regulator@8 {
622 regulator-name= "vccio_pmu";
623 regulator-min-microvolt = <1800000>;
624 regulator-max-microvolt = <1800000>;
625 regulator-initial-state = <3>;
626 regulator-state-mem {
627 regulator-state-enabled;
628 regulator-state-uv = <1800000>;
632 rk818_ldo6_reg: regulator@9 {
633 regulator-name= "vdd10_lcd";
634 regulator-min-microvolt = <1000000>;
635 regulator-max-microvolt = <1000000>;
636 regulator-initial-state = <3>;
637 regulator-state-mem {
638 regulator-state-disabled;
639 regulator-state-uv = <1000000>;
643 rk818_ldo7_reg: regulator@10 {
644 regulator-name= "vcc_18";
645 regulator-min-microvolt = <1800000>;
646 regulator-max-microvolt = <1800000>;
647 regulator-initial-state = <3>;
648 regulator-state-mem {
649 regulator-state-enabled;
650 regulator-state-uv = <1800000>;
654 rk818_ldo8_reg: regulator@11 {
655 regulator-name= "vccio_wl";
656 regulator-min-microvolt = <1800000>;
657 regulator-max-microvolt = <1800000>;
658 regulator-initial-state = <3>;
659 regulator-state-mem {
660 regulator-state-enabled;
661 regulator-state-uv = <1800000>;
665 rk818_ldo9_reg: regulator@12 {
666 regulator-name= "vcc_sd";
667 regulator-min-microvolt = <1800000>;
668 regulator-max-microvolt = <3300000>;
669 regulator-initial-state = <3>;
670 regulator-state-mem {
671 regulator-state-enabled;
672 regulator-state-uv = <3300000>;
676 rk818_ldo10_reg: regulator@13 {
677 regulator-name= "rk818_ldo10";
678 regulator-state-mem {
679 regulator-state-disabled;
686 reg = <0x00000000 0x28000000>; /* 640MB */