3 #include <dt-bindings/interrupt-controller/arm-gic.h>
4 #include <dt-bindings/rkfb/rk_fb.h>
6 #include "../../../arm/boot/dts/lcd-ld089wu1-mipi.dtsi"
9 bootargs = "earlyprintk=uart8250-32bit,0xff690000";
13 compatible = "wlan-platdata";
15 rockchip,grf = <&grf>;
17 /* wifi_chip_type - wifi chip define
18 * ap6210, ap6330, ap6335
19 * rtl8188eu, rtl8723bs, rtl8723bu
22 wifi_chip_type = "ap6210";
24 sdio_vref = <1800>; //1800mv or 3300mv
25 power_pmu_regulator = "rk818_ldo8_reg";
26 power_pmu_enable_level = <1>; //1->HIGH, 0->LOW
27 vref_pmu_regulator = "rk818_ldo8_reg";
28 vref_pmu_enable_level = <1>; //1->HIGH, 0->LOW
30 WIFI,poweren_gpio = <&gpio3 GPIO_A4 GPIO_ACTIVE_HIGH>;
31 WIFI,host_wake_irq = <&gpio3 GPIO_A6 GPIO_ACTIVE_HIGH>;
37 compatible = "bluetooth-platdata";
38 uart_rts_gpios = <&gpio2 GPIO_D3 GPIO_ACTIVE_LOW>;
39 pinctrl-names = "default","rts_gpio";
40 pinctrl-0 = <&uart0_rts>;
41 pinctrl-1 = <&uart0_rts_gpio>;
43 BT,power_gpio = <&gpio3 GPIO_A3 GPIO_ACTIVE_HIGH>;
44 BT,reset_gpio = <&gpio3 GPIO_A5 GPIO_ACTIVE_HIGH>;
45 BT,wake_gpio = <&gpio3 GPIO_A2 GPIO_ACTIVE_HIGH>;
46 BT,wake_host_irq = <&gpio3 GPIO_A7 GPIO_ACTIVE_HIGH>;
52 compatible = "hall_och165t";
53 type = <SENSOR_TYPE_HALL>;
54 irq-gpio = <&gpio0 GPIO_C0 IRQ_TYPE_EDGE_BOTH>;
57 backlight: backlight {
58 compatible = "pwm-backlight";
59 pwms = <&pwm0 0 25000>;
60 brightness-levels = <0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
61 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
62 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
63 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87
64 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109
65 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
66 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147
67 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166
68 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185
69 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204
70 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
71 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242
72 243 244 245 246 247 248 249 250 251 252 253 254 255>;
73 default-brightness-level = <128>;
74 enable-gpios = <&gpio0 GPIO_C4 GPIO_ACTIVE_HIGH>;
78 compatible = "rockchip_pwm_regulator";
79 pwms = <&pwm1 0 2000>;
81 rockchip,pwm_voltage_map= <925000 950000 975000 1000000 1025000 1050000 1075000 1100000 1125000 1150000 1175000 1200000 1225000 1250000 1275000 1300000 1325000 1350000 1375000 1400000>;
82 rockchip,pwm_voltage= <1000000>;
83 rockchip,pwm_min_voltage= <925000>;
84 rockchip,pwm_max_voltage= <1400000>;
85 rockchip,pwm_suspend_voltage= <950000>;
86 rockchip,pwm_coefficient= <475>;
90 pwm_reg0: regulator@0 {
91 regulator-compatible = "pwm_dcdc1";
92 regulator-name= "vdd_logic";
93 regulator-min-microvolt = <925000>;
94 regulator-max-microvolt = <1400000>;
101 codec_hdmi_i2s: codec-hdmi-i2s {
102 compatible = "hdmi-i2s";
105 codec_hdmi_spdif: codec-hdmi-spdif {
106 compatible = "hdmi-spdif";
110 compatible = "rockchip-hdmi-i2s";
113 audio-codec = <&codec_hdmi_i2s>;
114 i2s-controller = <&i2s0>;
120 rockchip-hdmi-spdif {
121 compatible = "rockchip-hdmi-spdif";
124 audio-codec = <&codec_hdmi_spdif>;
125 i2s-controller = <&spdif>;
131 compatible = "rockchip-es8316";
134 audio-codec = <&es8316>;
135 i2s-controller = <&i2s0>;
142 compatible = "rockchip,rk3368-io-voltage-domain";
143 rockchip,grf = <&grf>;
144 rockchip,pmugrf = <&pmugrf>;
147 gpio30-supply = <&rk818_dcdc4_reg>; /*APIO1_VDD*/
148 wifi-supply = <&rk818_ldo8_reg>; /*APIO2_VDD*/
149 audio-supply = <&rk818_dcdc4_reg>; /*APIO3_VDD*/
150 gpio1830-supply = <&rk818_dcdc4_reg>; /*ADIO4_VDD*/
151 sdcard-supply = <&rk818_ldo9_reg>; /*SDMMC_VDD*/
154 pmu-supply = <&rk818_ldo5_reg>; /*PMUIO_VDD*/
155 vop-supply = <&rk818_ldo5_reg>; /*LCDC_VDD*/
160 tsadc-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
161 //tsadc-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
166 //used for init some gpio
167 init-gpios = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH>;
171 rockchip,pins = <0 GPIO_C7 RK_FUNC_GPIO &pcfg_pull_down>;
174 rockchip,pins = <0 GPIO_A3 RK_FUNC_3 &pcfg_pull_none>;
177 rockchip,pins = <0 GPIO_C2 RK_FUNC_GPIO &pcfg_pull_down>;
180 rockchip,pins = <0 GPIO_C3 RK_FUNC_GPIO &pcfg_pull_down>;
184 rockchip,pins = <0 GPIO_C1 RK_FUNC_GPIO &pcfg_pull_up>;
192 status = "disabled"; // used nand set "disabled" ,used emmc set "okay"
196 status = "okay"; // used nand set "disabled" ,used emmc set "okay"
200 clock-frequency = <150000000>;
201 clock-freq-min-max = <400000 150000000>;
208 supports-DDR_MODE; //you should set the two value in your project. only close in RK3288-SDK board.
212 keep-power-in-suspend;
219 clock-frequency = <50000000>;
220 clock-freq-min-max = <400000 50000000>;
224 card-detect-delay = <200>;
227 keep-power-in-suspend;
229 vmmc-supply = <&rk818_ldo1_reg>;
234 clock-frequency = <50000000>;
235 clock-freq-min-max = <200000 50000000>;
239 keep-power-in-suspend;
270 dma-names = "!tx", "!rx";
271 pinctrl-0 = <&uart0_xfer &uart0_cts>;
277 compatible = "silergy,syr82x";
281 #address-cells = <1>;
283 syr827_dc1: regulator@0 {
285 regulator-compatible = "syr82x_dcdc1";
286 regulator-name = "vdd_arm";
287 regulator-min-microvolt = <712500>;
288 regulator-max-microvolt = <1500000>;
291 regulator-initial-mode = <0x2>;
292 regulator-initial-state = <3>;
293 regulator-state-mem {
294 regulator-state-mode = <0x2>;
295 regulator-state-disabled;
296 regulator-state-uv = <900000>;
302 compatible = "silergy,syr82x";
306 #address-cells = <1>;
308 syr828_dc1: regulator@0 {
310 regulator-compatible = "syr82x_dcdc1";
311 regulator-name = "vdd_gpu";
312 regulator-min-microvolt = <712500>;
313 regulator-max-microvolt = <1500000>;
316 regulator-initial-mode = <0x2>;
317 regulator-initial-state = <3>;
318 regulator-state-mem {
319 regulator-state-mode = <0x2>;
320 regulator-state-enabled;
321 regulator-state-uv = <900000>;
330 compatible = "rockchip,rk818";
332 ocv_table = <3400 3650 3693 3707 3731 3749 3760
333 3770 3782 3796 3812 3829 3852 3882
334 3915 3951 3981 4047 4086 4132 4182>;
335 design_capacity = <8650>;
336 design_qmax = <8800>;
337 max_overcharge = <100>;
339 max_charge_ilimitmA = <2000>;
340 max_charge_currentmA = <1800>;
341 max_charge_voltagemV = <4200>;
342 max_bat_voltagemV = <4200>;
343 sleep_enter_current = <600>;
344 sleep_exit_current = <600>;
345 support_uboot_chrg = <0>;
346 support_usb_adp = <1>;
347 support_dc_adp = <1>;
348 dc_det_gpio = <&gpio0 GPIO_C1 GPIO_ACTIVE_LOW>;
349 dc_det_pullup_inside = <1>;
351 test_charge_currentmA = <1800>;
352 test_charge_ilimitmA = <2000>;
361 compatible = "es8316";
363 spk-con-gpio = <&gpio0 GPIO_C3 GPIO_ACTIVE_HIGH>;
364 hp-det-gpio = <&gpio0 GPIO_C7 GPIO_ACTIVE_HIGH>;
372 compatible = "goodix,gt9xx";
374 touch-gpio = <&gpio0 GPIO_B4 IRQ_TYPE_LEVEL_LOW>;
375 reset-gpio = <&gpio0 GPIO_B3 GPIO_ACTIVE_HIGH>;
388 mpu6500_acc:mpu_acc@68{
389 compatible = "mpu6500_acc";
392 poll_delay_ms = <30>;
393 type = <SENSOR_TYPE_ACCEL>;
404 rockchip,disp-mode = <NO_DUAL>;
405 rockchip,uboot-logo-on = <0>;
410 display-timings = <&disp_timings>;
415 backlight = <&backlight>;
416 rockchip,mirror = <NO_MIRROR>;
417 rockchip,cabc_mode = <0>;
418 rockchip,fb-win-map = <FB_DEFAULT_ORDER>;
419 power_ctr: power_ctr {
420 rockchip,debug = <0>;
422 rockchip,power_type = <GPIO>;
423 gpios = <&gpio0 GPIO_C6 GPIO_ACTIVE_HIGH>;
424 rockchip,delay = <120>;
428 rockchip,power_type = <GPIO>;
429 gpios = <&gpio0 GPIO_C5 GPIO_ACTIVE_HIGH>;
430 rockchip,delay = <10>;
434 rockchip,power_type = <GPIO>;
435 gpios = <&gpio3 GPIO_D6 GPIO_ACTIVE_HIGH>;
436 rockchip,delay = <5>;
450 compatible = "rockchip_headset";
451 headset_gpio = <&gpio0 GPIO_C7 GPIO_ACTIVE_LOW>;
452 pinctrl-names = "default";
453 pinctrl-0 = <&gpio0_c7>;//gpio0_c7
454 io-channels = <&adc 2>;
457 hook_down_type = ; //interrupt hook key down status
462 compatible = "rockchip,key";
463 io-channels = <&adc 1>;
468 rockchip,adc_value = <1>;
473 label = "volume down";
474 rockchip,adc_value = <170>;
478 gpios = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
494 &clk_core_b_dvfs_table {
510 &clk_core_l_dvfs_table {
524 &clk_gpu_dvfs_table {
534 &clk_ddr_dvfs_table {
549 SYS_STATUS_NORMAL 528000
550 SYS_STATUS_SUSPEND 96000
551 SYS_STATUS_VIDEO_1080P 300000
552 SYS_STATUS_VIDEO_4K 600000
553 SYS_STATUS_PERFORMANCE 792000
554 SYS_STATUS_DUALVIEW 600000
555 SYS_STATUS_BOOST 400000
556 SYS_STATUS_ISP 533000
569 host_drv_gpio = <&gpio0 GPIO_A4 GPIO_ACTIVE_LOW>;
570 otg_drv_gpio = <&gpio0 GPIO_D1 GPIO_ACTIVE_LOW>;
571 rockchip,remote_wakeup;
572 rockchip,usb_irq_wakeup;
575 /include/ "../../../arm/boot/dts/rk818.dtsi"
577 gpios =<&gpio0 GPIO_A1 GPIO_ACTIVE_HIGH>,<&gpio0 GPIO_A0 GPIO_ACTIVE_LOW>;
578 rk818,system-power-controller;
579 pinctrl-names = "default";
580 pinctrl-0 = <&gpio0_c1>;
583 rk818_dcdc1_reg: regulator@0{
584 regulator-name= "vdd_arm";/*vcc arm*/
585 regulator-min-microvolt = <700000>;/*<725000>;*/
586 regulator-max-microvolt = <1500000>;
587 regulator-initial-mode = <0x2>;
588 regulator-initial-state = <3>;
589 regulator-state-mem {
590 regulator-state-mode = <0x2>;
591 regulator-state-disabled;
592 regulator-state-uv =<900000>;
596 rk818_dcdc2_reg: regulator@1 {
597 regulator-name= "vdd_logic";/*vcc gpu*/
598 regulator-min-microvolt = <700000>;
599 regulator-max-microvolt = <1200000>;
600 regulator-initial-mode = <0x2>;
601 regulator-initial-state = <3>;
602 regulator-state-mem {
603 regulator-state-mode = <0x2>;
604 regulator-state-enabled;
605 regulator-state-uv = <1200000>;
609 rk818_dcdc3_reg: regulator@2 {
610 regulator-name= "vcc_ddr";
611 regulator-min-microvolt = <1200000>;
612 regulator-max-microvolt = <1200000>;
613 regulator-initial-mode = <0x2>;
614 regulator-initial-state = <3>;
615 regulator-state-mem {
616 regulator-state-mode = <0x2>;
617 regulator-state-enabled;
618 regulator-state-uv = <1200000>;
622 rk818_dcdc4_reg: regulator@3 {
623 regulator-name= "vccio";
624 regulator-min-microvolt = <3300000>;
625 regulator-max-microvolt = <3300000>;
626 regulator-initial-mode = <0x2>;
627 regulator-initial-state = <3>;
628 regulator-state-mem {
629 regulator-state-mode = <0x2>;
630 regulator-state-enabled;
631 regulator-state-uv = <3000000>;
635 rk818_ldo1_reg: regulator@4 {
636 regulator-name= "vcc_codec";
637 regulator-min-microvolt = <3300000>;
638 regulator-max-microvolt = <3300000>;
639 regulator-initial-state = <3>;
640 regulator-state-mem {
641 regulator-state-enabled;
642 regulator-state-uv = <3300000>;
646 rk818_ldo2_reg: regulator@5 {
647 regulator-name= "vcc_tp";
648 regulator-min-microvolt = <3300000>;
649 regulator-max-microvolt = <3300000>;
650 regulator-initial-state = <3>;
651 regulator-state-mem {
652 regulator-state-enabled;
653 regulator-state-uv = <3300000>;
657 rk818_ldo3_reg: regulator@6 {
658 regulator-name= "vdd_10";
659 regulator-min-microvolt = <1000000>;
660 regulator-max-microvolt = <1000000>;
661 regulator-initial-state = <3>;
662 regulator-state-mem {
663 regulator-state-enabled;
664 regulator-state-uv = <1000000>;
668 rk818_ldo4_reg:regulator@7 {
669 regulator-name= "vcc18_lcd";
670 regulator-min-microvolt = <1800000>;
671 regulator-max-microvolt = <1800000>;
672 regulator-initial-state = <3>;
673 regulator-state-mem {
674 regulator-state-disabled;
675 regulator-state-uv = <1800000>;
679 rk818_ldo5_reg: regulator@8 {
680 regulator-name= "vccio_pmu";
681 regulator-min-microvolt = <1800000>;
682 regulator-max-microvolt = <1800000>;
683 regulator-initial-state = <3>;
684 regulator-state-mem {
685 regulator-state-enabled;
686 regulator-state-uv = <1800000>;
690 rk818_ldo6_reg: regulator@9 {
691 regulator-name= "vdd10_lcd";
692 regulator-min-microvolt = <1000000>;
693 regulator-max-microvolt = <1000000>;
694 regulator-initial-state = <3>;
695 regulator-state-mem {
696 regulator-state-disabled;
697 regulator-state-uv = <1000000>;
701 rk818_ldo7_reg: regulator@10 {
702 regulator-name= "vcc_18";
703 regulator-min-microvolt = <1800000>;
704 regulator-max-microvolt = <1800000>;
705 regulator-initial-state = <3>;
706 regulator-state-mem {
707 regulator-state-enabled;
708 regulator-state-uv = <1800000>;
712 rk818_ldo8_reg: regulator@11 {
713 regulator-name= "vccio_wl";
714 regulator-min-microvolt = <1800000>;
715 regulator-max-microvolt = <1800000>;
716 regulator-initial-state = <3>;
717 regulator-state-mem {
718 regulator-state-enabled;
719 regulator-state-uv = <1800000>;
723 rk818_ldo9_reg: regulator@12 {
724 regulator-name= "vcc_sd";
725 regulator-min-microvolt = <1800000>;
726 regulator-max-microvolt = <3300000>;
727 regulator-initial-state = <3>;
728 regulator-state-mem {
729 regulator-state-enabled;
730 regulator-state-uv = <3300000>;
734 rk818_ldo10_reg: regulator@13 {
735 regulator-name= "rk818_ldo10";
736 regulator-state-mem {
737 regulator-state-disabled;
744 reg = <0x00000000 0x00000000>; /* 0MB */