3 #include <dt-bindings/interrupt-controller/arm-gic.h>
4 #include <dt-bindings/rkfb/rk_fb.h>
6 #include "../../../arm/boot/dts/lcd-ld089wu1-mipi.dtsi"
9 bootargs = "earlyprintk=uart8250-32bit,0xff690000 clk_ignore_unused";
13 compatible = "wlan-platdata";
15 rockchip,grf = <&grf>;
17 /* wifi_chip_type - wifi chip define
18 * ap6210, ap6330, ap6335
19 * rtl8188eu, rtl8723bs, rtl8723bu
22 wifi_chip_type = "ap6210";
24 sdio_vref = <1800>; //1800mv or 3300mv
25 power_pmu_regulator = "rk818_ldo8_reg";
26 power_pmu_enable_level = <1>; //1->HIGH, 0->LOW
27 vref_pmu_regulator = "rk818_ldo8_reg";
28 vref_pmu_enable_level = <1>; //1->HIGH, 0->LOW
30 WIFI,poweren_gpio = <&gpio3 GPIO_A4 GPIO_ACTIVE_HIGH>;
31 WIFI,host_wake_irq = <&gpio3 GPIO_A6 GPIO_ACTIVE_HIGH>;
37 compatible = "bluetooth-platdata";
38 uart_rts_gpios = <&gpio2 GPIO_D3 GPIO_ACTIVE_LOW>;
39 pinctrl-names = "default","rts_gpio";
40 pinctrl-0 = <&uart0_rts>;
41 pinctrl-1 = <&uart0_rts_gpio>;
43 BT,power_gpio = <&gpio3 GPIO_A3 GPIO_ACTIVE_HIGH>;
44 BT,reset_gpio = <&gpio3 GPIO_A5 GPIO_ACTIVE_HIGH>;
45 BT,wake_gpio = <&gpio3 GPIO_A2 GPIO_ACTIVE_HIGH>;
46 BT,wake_host_irq = <&gpio3 GPIO_A7 GPIO_ACTIVE_HIGH>;
52 compatible = "hall_och165t";
53 type = <SENSOR_TYPE_HALL>;
54 irq-gpio = <&gpio0 GPIO_C0 IRQ_TYPE_EDGE_BOTH>;
58 compatible = "pwm-backlight";
59 pwms = <&pwm0 0 25000>;
60 brightness-levels = <255 254 253 252 251 250 249 248 247 246 245 244 243 242 241 240
61 239 238 237 236 235 234 233 232 231 230 229 228 227 226 225 224 223 222 221 220
62 219 218 217 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200
63 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180
64 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160
65 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140
66 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120
67 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100
68 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70
69 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40
70 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
72 default-brightness-level = <200>;
73 enable-gpios = <&gpio0 GPIO_C4 GPIO_ACTIVE_HIGH>;
77 compatible = "rockchip_pwm_regulator";
78 pwms = <&pwm1 0 2000>;
80 rockchip,pwm_voltage_map= <925000 950000 975000 1000000 1025000 1050000 1075000 1100000 1125000 1150000 1175000 1200000 1225000 1250000 1275000 1300000 1325000 1350000 1375000 1400000>;
81 rockchip,pwm_voltage= <1000000>;
82 rockchip,pwm_min_voltage= <925000>;
83 rockchip,pwm_max_voltage= <1400000>;
84 rockchip,pwm_suspend_voltage= <950000>;
85 rockchip,pwm_coefficient= <475>;
89 pwm_reg0: regulator@0 {
90 regulator-compatible = "pwm_dcdc1";
91 regulator-name= "vdd_logic";
92 regulator-min-microvolt = <925000>;
93 regulator-max-microvolt = <1400000>;
100 codec_hdmi_i2s: codec-hdmi-i2s {
101 compatible = "hdmi-i2s";
104 codec_hdmi_spdif: codec-hdmi-spdif {
105 compatible = "hdmi-spdif";
109 compatible = "rockchip-hdmi-i2s";
112 audio-codec = <&codec_hdmi_i2s>;
113 i2s-controller = <&i2s0>;
119 rockchip-hdmi-spdif {
120 compatible = "rockchip-hdmi-spdif";
123 audio-codec = <&codec_hdmi_spdif>;
124 i2s-controller = <&spdif>;
130 compatible = "rockchip-es8316";
133 audio-codec = <&es8316>;
134 i2s-controller = <&i2s0>;
141 compatible = "rockchip,rk3368-io-voltage-domain";
142 rockchip,grf = <&grf>;
143 rockchip,pmugrf = <&pmugrf>;
146 gpio30-supply = <&rk818_dcdc4_reg>; /*APIO1_VDD*/
147 wifi-supply = <&rk818_ldo8_reg>; /*APIO2_VDD*/
148 audio-supply = <&rk818_dcdc4_reg>; /*APIO3_VDD*/
149 gpio1830-supply = <&rk818_dcdc4_reg>; /*ADIO4_VDD*/
150 sdcard-supply = <&rk818_ldo9_reg>; /*SDMMC_VDD*/
153 pmu-supply = <&rk818_ldo5_reg>; /*PMUIO_VDD*/
154 vop-supply = <&rk818_ldo5_reg>; /*LCDC_VDD*/
159 //used for init some gpio
160 init-gpios = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH>;
164 rockchip,pins = <0 GPIO_C7 RK_FUNC_GPIO &pcfg_pull_down>;
167 rockchip,pins = <0 GPIO_A3 RK_FUNC_3 &pcfg_pull_none>;
170 rockchip,pins = <0 GPIO_C2 RK_FUNC_GPIO &pcfg_pull_down>;
179 status = "disabled"; // used nand set "disabled" ,used emmc set "okay"
183 status = "okay"; // used nand set "disabled" ,used emmc set "okay"
187 clock-frequency = <150000000>;
188 clock-freq-min-max = <400000 150000000>;
195 supports-DDR_MODE; //you should set the two value in your project. only close in RK3288-SDK board.
199 keep-power-in-suspend;
206 clock-frequency = <50000000>;
207 clock-freq-min-max = <400000 50000000>;
211 card-detect-delay = <200>;
214 keep-power-in-suspend;
216 vmmc-supply = <&rk818_ldo1_reg>;
221 clock-frequency = <50000000>;
222 clock-freq-min-max = <200000 50000000>;
226 keep-power-in-suspend;
249 dma-names = "!tx", "!rx";
250 pinctrl-0 = <&uart0_xfer &uart0_cts>;
256 compatible = "silergy,syr82x";
260 #address-cells = <1>;
262 syr827_dc1: regulator@0 {
264 regulator-compatible = "syr82x_dcdc1";
265 regulator-name = "vdd_arm";
266 regulator-min-microvolt = <712500>;
267 regulator-max-microvolt = <1500000>;
270 regulator-initial-mode = <0x2>;
271 regulator-initial-state = <3>;
272 regulator-state-mem {
273 regulator-state-mode = <0x2>;
274 regulator-state-disabled;
275 regulator-state-uv = <900000>;
281 compatible = "silergy,syr82x";
285 #address-cells = <1>;
287 syr828_dc1: regulator@0 {
289 regulator-compatible = "syr82x_dcdc1";
290 regulator-name = "vdd_gpu";
291 regulator-min-microvolt = <712500>;
292 regulator-max-microvolt = <1500000>;
295 regulator-initial-mode = <0x2>;
296 regulator-initial-state = <3>;
297 regulator-state-mem {
298 regulator-state-mode = <0x2>;
299 regulator-state-enabled;
300 regulator-state-uv = <900000>;
309 compatible = "rockchip,rk818";
311 ocv_table = <3300 3599 3671 3701 3728 3746 3762
312 3772 3781 3792 3816 3836 3866 3910
313 3942 3971 4002 4050 4088 4132 4183>;
314 design_capacity = <3914>;
315 design_qmax = <4000>;
316 max_overcharge = <100>;
317 max_charge_currentmA = <1500>;
318 max_charge_voltagemV = <4260>;
319 max_bat_voltagemV = <4200>;
320 sleep_enter_current = <150>;
321 sleep_exit_current = <180>;
329 compatible = "es8316";
338 compatible = "goodix,gt9xx";
340 touch-gpio = <&gpio0 GPIO_B4 IRQ_TYPE_LEVEL_LOW>;
341 reset-gpio = <&gpio0 GPIO_B3 GPIO_ACTIVE_HIGH>;
356 compatible = "mpu6050";
358 mpu-int_config = <0x10>;
359 mpu-level_shifter = <0>;
360 mpu-orientation = <0 1 0 1 0 0 0 0 1>;
364 irq-gpio = <&gpio3 GPIO_B6 IRQ_TYPE_LEVEL_LOW>;
370 compatible = "mpu_ak8963";
373 compass-adapt_num = <0>;
374 compass-orientation = <1 0 0 0 1 0 0 0 1>;
390 rockchip,disp-mode = <NO_DUAL>;
391 rockchip,uboot-logo-on = <0>;
396 display-timings = <&disp_timings>;
401 rockchip,mirror = <NO_MIRROR>;
402 rockchip,cabc_mode = <0>;
403 rockchip,fb-win-map = <FB_DEFAULT_ORDER>;
404 power_ctr: power_ctr {
405 rockchip,debug = <0>;
407 rockchip,power_type = <GPIO>;
408 gpios = <&gpio0 GPIO_C6 GPIO_ACTIVE_HIGH>;
409 rockchip,delay = <120>;
413 rockchip,power_type = <GPIO>;
414 gpios = <&gpio0 GPIO_C5 GPIO_ACTIVE_HIGH>;
415 rockchip,delay = <10>;
419 rockchip,power_type = <GPIO>;
420 gpios = <&gpio3 GPIO_D6 GPIO_ACTIVE_HIGH>;
421 rockchip,delay = <5>;
429 rockchips,hdmi_audio_source = <0>;
436 compatible = "rockchip_headset";
437 headset_gpio = <&gpio0 GPIO_C7 GPIO_ACTIVE_LOW>;
438 pinctrl-names = "default";
439 pinctrl-0 = <&gpio0_c7>;//gpio0_c7
440 io-channels = <&adc 2>;
443 hook_down_type = ; //interrupt hook key down status
448 compatible = "rockchip,key";
449 io-channels = <&adc 1>;
454 rockchip,adc_value = <1>;
459 label = "volume down";
460 rockchip,adc_value = <170>;
464 gpios = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
480 &clk_ddr_dvfs_table {
491 SYS_STATUS_NORMAL 400000
492 SYS_STATUS_SUSPEND 200000
493 SYS_STATUS_VIDEO_1080P 240000
494 SYS_STATUS_VIDEO_4K 400000
495 SYS_STATUS_PERFORMANCE 528000
496 SYS_STATUS_DUALVIEW 400000
497 SYS_STATUS_BOOST 324000
498 SYS_STATUS_ISP 400000
511 host_drv_gpio = <&gpio0 GPIO_A4 GPIO_ACTIVE_LOW>;
512 otg_drv_gpio = <&gpio0 GPIO_D1 GPIO_ACTIVE_LOW>;
513 rockchip,remote_wakeup;
514 rockchip,usb_irq_wakeup;
517 /include/ "../../../arm/boot/dts/rk818.dtsi"
519 gpios =<&gpio0 GPIO_A1 GPIO_ACTIVE_HIGH>,<&gpio0 GPIO_A0 GPIO_ACTIVE_LOW>;
520 rk818,system-power-controller;
524 rk818_dcdc1_reg: regulator@0{
525 regulator-name= "vdd_arm";/*vcc arm*/
526 regulator-min-microvolt = <700000>;/*<725000>;*/
527 regulator-max-microvolt = <1500000>;
528 regulator-initial-mode = <0x2>;
529 regulator-initial-state = <3>;
530 regulator-state-mem {
531 regulator-state-mode = <0x2>;
532 regulator-state-enabled;
533 regulator-state-uv =<900000>;
537 rk818_dcdc2_reg: regulator@1 {
538 regulator-name= "vdd_gpu";/*vcc gpu*/
539 regulator-min-microvolt = <700000>;
540 regulator-max-microvolt = <1200000>;
541 regulator-initial-mode = <0x2>;
542 regulator-initial-state = <3>;
543 regulator-state-mem {
544 regulator-state-mode = <0x2>;
545 regulator-state-enabled;
546 regulator-state-uv = <1200000>;
550 rk818_dcdc3_reg: regulator@2 {
551 regulator-name= "vcc_ddr";
552 regulator-min-microvolt = <1200000>;
553 regulator-max-microvolt = <1200000>;
554 regulator-initial-mode = <0x2>;
555 regulator-initial-state = <3>;
556 regulator-state-mem {
557 regulator-state-mode = <0x2>;
558 regulator-state-enabled;
559 regulator-state-uv = <1200000>;
563 rk818_dcdc4_reg: regulator@3 {
564 regulator-name= "vccio";
565 regulator-min-microvolt = <3000000>;
566 regulator-max-microvolt = <3000000>;
567 regulator-initial-mode = <0x2>;
568 regulator-initial-state = <3>;
569 regulator-state-mem {
570 regulator-state-mode = <0x2>;
571 regulator-state-enabled;
572 regulator-state-uv = <3000000>;
576 rk818_ldo1_reg: regulator@4 {
577 regulator-name= "vcc_codec";
578 regulator-min-microvolt = <3300000>;
579 regulator-max-microvolt = <3300000>;
580 regulator-initial-state = <3>;
581 regulator-state-mem {
582 regulator-state-enabled;
583 regulator-state-uv = <3300000>;
587 rk818_ldo2_reg: regulator@5 {
588 regulator-name= "vcc_tp";
589 regulator-min-microvolt = <3300000>;
590 regulator-max-microvolt = <3300000>;
591 regulator-initial-state = <3>;
592 regulator-state-mem {
593 regulator-state-enabled;
594 regulator-state-uv = <3300000>;
598 rk818_ldo3_reg: regulator@6 {
599 regulator-name= "vdd_10";
600 regulator-min-microvolt = <1000000>;
601 regulator-max-microvolt = <1000000>;
602 regulator-initial-state = <3>;
603 regulator-state-mem {
604 regulator-state-enabled;
605 regulator-state-uv = <1000000>;
609 rk818_ldo4_reg:regulator@7 {
610 regulator-name= "vcc18_lcd";
611 regulator-min-microvolt = <1800000>;
612 regulator-max-microvolt = <1800000>;
613 regulator-initial-state = <3>;
614 regulator-state-mem {
615 regulator-state-disabled;
616 regulator-state-uv = <1800000>;
620 rk818_ldo5_reg: regulator@8 {
621 regulator-name= "vccio_pmu";
622 regulator-min-microvolt = <1800000>;
623 regulator-max-microvolt = <1800000>;
624 regulator-initial-state = <3>;
625 regulator-state-mem {
626 regulator-state-enabled;
627 regulator-state-uv = <1800000>;
631 rk818_ldo6_reg: regulator@9 {
632 regulator-name= "vdd10_lcd";
633 regulator-min-microvolt = <1000000>;
634 regulator-max-microvolt = <1000000>;
635 regulator-initial-state = <3>;
636 regulator-state-mem {
637 regulator-state-disabled;
638 regulator-state-uv = <1000000>;
642 rk818_ldo7_reg: regulator@10 {
643 regulator-name= "vcc_18";
644 regulator-min-microvolt = <1800000>;
645 regulator-max-microvolt = <1800000>;
646 regulator-initial-state = <3>;
647 regulator-state-mem {
648 regulator-state-enabled;
649 regulator-state-uv = <1800000>;
653 rk818_ldo8_reg: regulator@11 {
654 regulator-name= "vccio_wl";
655 regulator-min-microvolt = <1800000>;
656 regulator-max-microvolt = <1800000>;
657 regulator-initial-state = <3>;
658 regulator-state-mem {
659 regulator-state-enabled;
660 regulator-state-uv = <1800000>;
664 rk818_ldo9_reg: regulator@12 {
665 regulator-name= "vcc_sd";
666 regulator-min-microvolt = <1800000>;
667 regulator-max-microvolt = <3300000>;
668 regulator-initial-state = <3>;
669 regulator-state-mem {
670 regulator-state-enabled;
671 regulator-state-uv = <3300000>;
675 rk818_ldo10_reg: regulator@13 {
676 regulator-name= "rk818_ldo10";
677 regulator-state-mem {
678 regulator-state-disabled;
685 reg = <0x00000000 0x28000000>; /* 640MB */