2 * linux/arch/arm/mach-nomadik/board-8815nhk.c
4 * Copyright (C) STMicroelectronics
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License version 2, as
8 * published by the Free Software Foundation.
10 * NHK15 board specifc driver definition
12 #include <linux/types.h>
13 #include <linux/kernel.h>
14 #include <linux/init.h>
15 #include <linux/platform_device.h>
16 #include <linux/amba/bus.h>
17 #include <linux/amba/mmci.h>
18 #include <linux/interrupt.h>
19 #include <linux/gpio.h>
20 #include <linux/mtd/mtd.h>
21 #include <linux/mtd/nand.h>
22 #include <linux/mtd/onenand.h>
23 #include <linux/mtd/partitions.h>
24 #include <linux/i2c.h>
26 #include <linux/pinctrl/machine.h>
27 #include <linux/platform_data/pinctrl-nomadik.h>
28 #include <asm/hardware/vic.h>
29 #include <asm/sizes.h>
30 #include <asm/mach-types.h>
31 #include <asm/mach/arch.h>
32 #include <asm/mach/irq.h>
33 #include <asm/mach/flash.h>
34 #include <asm/mach/time.h>
38 #include <linux/platform_data/mtd-nomadik-nand.h>
39 #include <mach/fsmc.h>
43 /* Initial value for SRC control register: all timers use MXTAL/8 source */
44 #define SRC_CR_INIT_MASK 0x00007fff
45 #define SRC_CR_INIT_VAL 0x2aaa8000
47 /* These addresses span 16MB, so use three individual pages */
48 static struct resource nhk8815_nand_resources[] = {
51 .start = NAND_IO_ADDR,
52 .end = NAND_IO_ADDR + 0xfff,
53 .flags = IORESOURCE_MEM,
57 .end = NAND_IO_CMD + 0xfff,
58 .flags = IORESOURCE_MEM,
61 .start = NAND_IO_DATA,
62 .end = NAND_IO_DATA + 0xfff,
63 .flags = IORESOURCE_MEM,
67 static int nhk8815_nand_init(void)
69 /* FSMC setup for nand chip select (8-bit nand in 8815NHK) */
70 writel(0x0000000E, FSMC_PCR(0));
71 writel(0x000D0A00, FSMC_PMEM(0));
72 writel(0x00100A00, FSMC_PATT(0));
74 /* enable access to the chip select area */
75 writel(readl(FSMC_PCR(0)) | 0x04, FSMC_PCR(0));
81 * These partitions are the same as those used in the 2.6.20 release
82 * shipped by the vendor; the first two partitions are mandated
83 * by the boot ROM, and the bootloader area is somehow oversized...
85 static struct mtd_partition nhk8815_partitions[] = {
87 .name = "X-Loader(NAND)",
91 .name = "MemInit(NAND)",
92 .offset = MTDPART_OFS_APPEND,
95 .name = "BootLoader(NAND)",
96 .offset = MTDPART_OFS_APPEND,
99 .name = "Kernel zImage(NAND)",
100 .offset = MTDPART_OFS_APPEND,
103 .name = "Root Filesystem(NAND)",
104 .offset = MTDPART_OFS_APPEND,
107 .name = "User Filesystem(NAND)",
108 .offset = MTDPART_OFS_APPEND,
109 .size = MTDPART_SIZ_FULL,
113 static struct nomadik_nand_platform_data nhk8815_nand_data = {
114 .parts = nhk8815_partitions,
115 .nparts = ARRAY_SIZE(nhk8815_partitions),
116 .options = NAND_COPYBACK | NAND_CACHEPRG | NAND_NO_PADDING,
117 .init = nhk8815_nand_init,
120 static struct platform_device nhk8815_nand_device = {
121 .name = "nomadik_nand",
123 .platform_data = &nhk8815_nand_data,
125 .resource = nhk8815_nand_resources,
126 .num_resources = ARRAY_SIZE(nhk8815_nand_resources),
129 /* These are the partitions for the OneNand device, different from above */
130 static struct mtd_partition nhk8815_onenand_partitions[] = {
132 .name = "X-Loader(OneNAND)",
136 .name = "MemInit(OneNAND)",
137 .offset = MTDPART_OFS_APPEND,
140 .name = "BootLoader(OneNAND)",
141 .offset = MTDPART_OFS_APPEND,
142 .size = SZ_2M-SZ_256K,
144 .name = "SysImage(OneNAND)",
145 .offset = MTDPART_OFS_APPEND,
148 .name = "Root Filesystem(OneNAND)",
149 .offset = MTDPART_OFS_APPEND,
152 .name = "User Filesystem(OneNAND)",
153 .offset = MTDPART_OFS_APPEND,
154 .size = MTDPART_SIZ_FULL,
158 static struct onenand_platform_data nhk8815_onenand_data = {
159 .parts = nhk8815_onenand_partitions,
160 .nr_parts = ARRAY_SIZE(nhk8815_onenand_partitions),
163 static struct resource nhk8815_onenand_resource[] = {
166 .end = 0x30000000 + SZ_128K - 1,
167 .flags = IORESOURCE_MEM,
171 static struct platform_device nhk8815_onenand_device = {
172 .name = "onenand-flash",
175 .platform_data = &nhk8815_onenand_data,
177 .resource = nhk8815_onenand_resource,
178 .num_resources = ARRAY_SIZE(nhk8815_onenand_resource),
181 static void __init nhk8815_onenand_init(void)
183 #ifdef CONFIG_MTD_ONENAND
184 /* Set up SMCS0 for OneNand */
185 writel(0x000030db, FSMC_BCR(0));
186 writel(0x02100551, FSMC_BTR(0));
190 static struct mmci_platform_data mmcsd_plat_data = {
191 .ocr_mask = MMC_VDD_29_30,
196 .capabilities = MMC_CAP_MMC_HIGHSPEED |
197 MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA,
200 static int __init nhk8815_mmcsd_init(void)
204 ret = gpio_request(112, "card detect bias");
207 gpio_direction_output(112, 0);
208 amba_apb_device_add(NULL, "mmci", NOMADIK_SDI_BASE, SZ_4K, IRQ_SDMMC, 0, &mmcsd_plat_data, 0x10180180);
211 module_init(nhk8815_mmcsd_init);
213 static struct resource nhk8815_eth_resources[] = {
215 .name = "smc91x-regs",
216 .start = 0x34000000 + 0x300,
217 .end = 0x34000000 + SZ_64K - 1,
218 .flags = IORESOURCE_MEM,
220 .start = NOMADIK_GPIO_TO_IRQ(115),
221 .end = NOMADIK_GPIO_TO_IRQ(115),
222 .flags = IORESOURCE_IRQ | IRQF_TRIGGER_RISING,
226 static struct platform_device nhk8815_eth_device = {
228 .resource = nhk8815_eth_resources,
229 .num_resources = ARRAY_SIZE(nhk8815_eth_resources),
232 static int __init nhk8815_eth_init(void)
234 int gpio_nr = 115; /* hardwired in the board */
237 err = gpio_request(gpio_nr, "eth_irq");
238 if (!err) err = nmk_gpio_set_mode(gpio_nr, NMK_GPIO_ALT_GPIO);
239 if (!err) err = gpio_direction_input(gpio_nr);
241 pr_err("Error %i in %s\n", err, __func__);
244 device_initcall(nhk8815_eth_init);
246 static struct platform_device *nhk8815_platform_devices[] __initdata = {
247 &nhk8815_nand_device,
248 &nhk8815_onenand_device,
250 /* will add more devices */
253 static void __init nomadik_timer_init(void)
257 /* Configure timer sources in "system reset controller" ctrl reg */
258 src_cr = readl(io_p2v(NOMADIK_SRC_BASE));
259 src_cr &= SRC_CR_INIT_MASK;
260 src_cr |= SRC_CR_INIT_VAL;
261 writel(src_cr, io_p2v(NOMADIK_SRC_BASE));
263 nmdk_timer_init(io_p2v(NOMADIK_MTU0_BASE));
266 static struct sys_timer nomadik_timer = {
267 .init = nomadik_timer_init,
270 static struct i2c_board_info __initdata nhk8815_i2c0_devices[] = {
272 I2C_BOARD_INFO("stw4811", 0x2d),
276 static struct i2c_board_info __initdata nhk8815_i2c1_devices[] = {
278 I2C_BOARD_INFO("camera", 0x10),
281 I2C_BOARD_INFO("stw5095", 0x1a),
284 I2C_BOARD_INFO("lis3lv02dl", 0x1d),
288 static struct i2c_board_info __initdata nhk8815_i2c2_devices[] = {
290 I2C_BOARD_INFO("stw4811-usb", 0x2d),
294 static unsigned long out_low[] = { PIN_OUTPUT_LOW };
295 static unsigned long out_high[] = { PIN_OUTPUT_HIGH };
296 static unsigned long in_nopull[] = { PIN_INPUT_NOPULL };
297 static unsigned long in_pullup[] = { PIN_INPUT_PULLUP };
299 static struct pinctrl_map __initdata nhk8815_pinmap[] = {
300 PIN_MAP_MUX_GROUP_DEFAULT("uart0", "pinctrl-stn8815", "u0_a_1", "u0"),
301 PIN_MAP_MUX_GROUP_DEFAULT("uart1", "pinctrl-stn8815", "u1_a_1", "u1"),
302 /* Hog in MMC/SD card mux */
303 PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-stn8815", "mmcsd_a_1", "mmcsd"),
305 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO8_B10", out_low),
307 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO9_A10", in_pullup),
309 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO10_C11", out_high),
311 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO11_B11", in_pullup),
312 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO12_A11", in_pullup),
313 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO13_C12", in_pullup),
314 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO14_B12", in_pullup),
316 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO15_A12", out_high),
318 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO16_C13", out_high),
320 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO24_C15", in_pullup),
322 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO111_H21", in_nopull),
324 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO112_J21", out_low),
327 static void __init nhk8815_platform_init(void)
329 pinctrl_register_mappings(nhk8815_pinmap, ARRAY_SIZE(nhk8815_pinmap));
330 cpu8815_platform_init();
331 nhk8815_onenand_init();
332 platform_add_devices(nhk8815_platform_devices,
333 ARRAY_SIZE(nhk8815_platform_devices));
335 amba_apb_device_add(NULL, "uart0", NOMADIK_UART0_BASE, SZ_4K, IRQ_UART0, 0, NULL, 0);
336 amba_apb_device_add(NULL, "uart1", NOMADIK_UART1_BASE, SZ_4K, IRQ_UART1, 0, NULL, 0);
338 i2c_register_board_info(0, nhk8815_i2c0_devices,
339 ARRAY_SIZE(nhk8815_i2c0_devices));
340 i2c_register_board_info(1, nhk8815_i2c1_devices,
341 ARRAY_SIZE(nhk8815_i2c1_devices));
342 i2c_register_board_info(2, nhk8815_i2c2_devices,
343 ARRAY_SIZE(nhk8815_i2c2_devices));
346 MACHINE_START(NOMADIK, "NHK8815")
347 /* Maintainer: ST MicroElectronics */
348 .atag_offset = 0x100,
349 .map_io = cpu8815_map_io,
350 .init_irq = cpu8815_init_irq,
351 .handle_irq = vic_handle_irq,
352 .timer = &nomadik_timer,
353 .init_machine = nhk8815_platform_init,
354 .restart = cpu8815_restart,