2 * linux/arch/arm/mach-nomadik/board-8815nhk.c
4 * Copyright (C) STMicroelectronics
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License version 2, as
8 * published by the Free Software Foundation.
10 * NHK15 board specifc driver definition
12 #include <linux/types.h>
13 #include <linux/kernel.h>
14 #include <linux/init.h>
15 #include <linux/platform_device.h>
16 #include <linux/amba/bus.h>
17 #include <linux/amba/mmci.h>
18 #include <linux/interrupt.h>
19 #include <linux/gpio.h>
20 #include <linux/mtd/mtd.h>
21 #include <linux/mtd/nand.h>
22 #include <linux/mtd/onenand.h>
23 #include <linux/mtd/partitions.h>
24 #include <linux/i2c.h>
26 #include <linux/pinctrl/machine.h>
27 #include <asm/hardware/vic.h>
28 #include <asm/sizes.h>
29 #include <asm/mach-types.h>
30 #include <asm/mach/arch.h>
31 #include <asm/mach/irq.h>
32 #include <asm/mach/flash.h>
33 #include <asm/mach/time.h>
35 #include <plat/gpio-nomadik.h>
37 #include <plat/pincfg.h>
39 #include <mach/nand.h>
40 #include <mach/fsmc.h>
44 /* Initial value for SRC control register: all timers use MXTAL/8 source */
45 #define SRC_CR_INIT_MASK 0x00007fff
46 #define SRC_CR_INIT_VAL 0x2aaa8000
48 /* These addresses span 16MB, so use three individual pages */
49 static struct resource nhk8815_nand_resources[] = {
52 .start = NAND_IO_ADDR,
53 .end = NAND_IO_ADDR + 0xfff,
54 .flags = IORESOURCE_MEM,
58 .end = NAND_IO_CMD + 0xfff,
59 .flags = IORESOURCE_MEM,
62 .start = NAND_IO_DATA,
63 .end = NAND_IO_DATA + 0xfff,
64 .flags = IORESOURCE_MEM,
68 static int nhk8815_nand_init(void)
70 /* FSMC setup for nand chip select (8-bit nand in 8815NHK) */
71 writel(0x0000000E, FSMC_PCR(0));
72 writel(0x000D0A00, FSMC_PMEM(0));
73 writel(0x00100A00, FSMC_PATT(0));
75 /* enable access to the chip select area */
76 writel(readl(FSMC_PCR(0)) | 0x04, FSMC_PCR(0));
82 * These partitions are the same as those used in the 2.6.20 release
83 * shipped by the vendor; the first two partitions are mandated
84 * by the boot ROM, and the bootloader area is somehow oversized...
86 static struct mtd_partition nhk8815_partitions[] = {
88 .name = "X-Loader(NAND)",
92 .name = "MemInit(NAND)",
93 .offset = MTDPART_OFS_APPEND,
96 .name = "BootLoader(NAND)",
97 .offset = MTDPART_OFS_APPEND,
100 .name = "Kernel zImage(NAND)",
101 .offset = MTDPART_OFS_APPEND,
104 .name = "Root Filesystem(NAND)",
105 .offset = MTDPART_OFS_APPEND,
108 .name = "User Filesystem(NAND)",
109 .offset = MTDPART_OFS_APPEND,
110 .size = MTDPART_SIZ_FULL,
114 static struct nomadik_nand_platform_data nhk8815_nand_data = {
115 .parts = nhk8815_partitions,
116 .nparts = ARRAY_SIZE(nhk8815_partitions),
117 .options = NAND_COPYBACK | NAND_CACHEPRG | NAND_NO_PADDING \
119 .init = nhk8815_nand_init,
122 static struct platform_device nhk8815_nand_device = {
123 .name = "nomadik_nand",
125 .platform_data = &nhk8815_nand_data,
127 .resource = nhk8815_nand_resources,
128 .num_resources = ARRAY_SIZE(nhk8815_nand_resources),
131 /* These are the partitions for the OneNand device, different from above */
132 static struct mtd_partition nhk8815_onenand_partitions[] = {
134 .name = "X-Loader(OneNAND)",
138 .name = "MemInit(OneNAND)",
139 .offset = MTDPART_OFS_APPEND,
142 .name = "BootLoader(OneNAND)",
143 .offset = MTDPART_OFS_APPEND,
144 .size = SZ_2M-SZ_256K,
146 .name = "SysImage(OneNAND)",
147 .offset = MTDPART_OFS_APPEND,
150 .name = "Root Filesystem(OneNAND)",
151 .offset = MTDPART_OFS_APPEND,
154 .name = "User Filesystem(OneNAND)",
155 .offset = MTDPART_OFS_APPEND,
156 .size = MTDPART_SIZ_FULL,
160 static struct onenand_platform_data nhk8815_onenand_data = {
161 .parts = nhk8815_onenand_partitions,
162 .nr_parts = ARRAY_SIZE(nhk8815_onenand_partitions),
165 static struct resource nhk8815_onenand_resource[] = {
168 .end = 0x30000000 + SZ_128K - 1,
169 .flags = IORESOURCE_MEM,
173 static struct platform_device nhk8815_onenand_device = {
174 .name = "onenand-flash",
177 .platform_data = &nhk8815_onenand_data,
179 .resource = nhk8815_onenand_resource,
180 .num_resources = ARRAY_SIZE(nhk8815_onenand_resource),
183 static void __init nhk8815_onenand_init(void)
185 #ifdef CONFIG_MTD_ONENAND
186 /* Set up SMCS0 for OneNand */
187 writel(0x000030db, FSMC_BCR(0));
188 writel(0x02100551, FSMC_BTR(0));
192 static struct mmci_platform_data mmcsd_plat_data = {
193 .ocr_mask = MMC_VDD_29_30,
198 .capabilities = MMC_CAP_MMC_HIGHSPEED |
199 MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA,
202 static int __init nhk8815_mmcsd_init(void)
206 ret = gpio_request(112, "card detect bias");
209 gpio_direction_output(112, 0);
210 amba_apb_device_add(NULL, "mmci", NOMADIK_SDI_BASE, SZ_4K, IRQ_SDMMC, 0, &mmcsd_plat_data, 0x10180180);
213 module_init(nhk8815_mmcsd_init);
215 static struct resource nhk8815_eth_resources[] = {
217 .name = "smc91x-regs",
218 .start = 0x34000000 + 0x300,
219 .end = 0x34000000 + SZ_64K - 1,
220 .flags = IORESOURCE_MEM,
222 .start = NOMADIK_GPIO_TO_IRQ(115),
223 .end = NOMADIK_GPIO_TO_IRQ(115),
224 .flags = IORESOURCE_IRQ | IRQF_TRIGGER_RISING,
228 static struct platform_device nhk8815_eth_device = {
230 .resource = nhk8815_eth_resources,
231 .num_resources = ARRAY_SIZE(nhk8815_eth_resources),
234 static int __init nhk8815_eth_init(void)
236 int gpio_nr = 115; /* hardwired in the board */
239 err = gpio_request(gpio_nr, "eth_irq");
240 if (!err) err = nmk_gpio_set_mode(gpio_nr, NMK_GPIO_ALT_GPIO);
241 if (!err) err = gpio_direction_input(gpio_nr);
243 pr_err("Error %i in %s\n", err, __func__);
246 device_initcall(nhk8815_eth_init);
248 static struct platform_device *nhk8815_platform_devices[] __initdata = {
249 &nhk8815_nand_device,
250 &nhk8815_onenand_device,
252 /* will add more devices */
255 static void __init nomadik_timer_init(void)
259 /* Configure timer sources in "system reset controller" ctrl reg */
260 src_cr = readl(io_p2v(NOMADIK_SRC_BASE));
261 src_cr &= SRC_CR_INIT_MASK;
262 src_cr |= SRC_CR_INIT_VAL;
263 writel(src_cr, io_p2v(NOMADIK_SRC_BASE));
265 nmdk_timer_init(io_p2v(NOMADIK_MTU0_BASE));
268 static struct sys_timer nomadik_timer = {
269 .init = nomadik_timer_init,
272 static struct i2c_board_info __initdata nhk8815_i2c0_devices[] = {
274 I2C_BOARD_INFO("stw4811", 0x2d),
278 static struct i2c_board_info __initdata nhk8815_i2c1_devices[] = {
280 I2C_BOARD_INFO("camera", 0x10),
283 I2C_BOARD_INFO("stw5095", 0x1a),
286 I2C_BOARD_INFO("lis3lv02dl", 0x1d),
290 static struct i2c_board_info __initdata nhk8815_i2c2_devices[] = {
292 I2C_BOARD_INFO("stw4811-usb", 0x2d),
296 static unsigned long out_low[] = { PIN_OUTPUT_LOW };
297 static unsigned long out_high[] = { PIN_OUTPUT_HIGH };
298 static unsigned long in_nopull[] = { PIN_INPUT_NOPULL };
299 static unsigned long in_pullup[] = { PIN_INPUT_PULLUP };
301 static struct pinctrl_map __initdata nhk8815_pinmap[] = {
302 PIN_MAP_MUX_GROUP_DEFAULT("uart0", "pinctrl-stn8815", "u0_a_1", "u0"),
303 PIN_MAP_MUX_GROUP_DEFAULT("uart1", "pinctrl-stn8815", "u1_a_1", "u1"),
304 /* Hog in MMC/SD card mux */
305 PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-stn8815", "mmcsd_a_1", "mmcsd"),
307 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO8_B10", out_low),
309 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO9_A10", in_pullup),
311 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO10_C11", out_high),
313 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO11_B11", in_pullup),
314 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO12_A11", in_pullup),
315 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO13_C12", in_pullup),
316 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO14_B12", in_pullup),
318 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO15_A12", out_high),
320 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO16_C13", out_high),
322 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO24_C15", in_pullup),
324 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO111_H21", in_nopull),
326 PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO112_J21", out_low),
329 static void __init nhk8815_platform_init(void)
331 pinctrl_register_mappings(nhk8815_pinmap, ARRAY_SIZE(nhk8815_pinmap));
332 cpu8815_platform_init();
333 nhk8815_onenand_init();
334 platform_add_devices(nhk8815_platform_devices,
335 ARRAY_SIZE(nhk8815_platform_devices));
337 amba_apb_device_add(NULL, "uart0", NOMADIK_UART0_BASE, SZ_4K, IRQ_UART0, 0, NULL, 0);
338 amba_apb_device_add(NULL, "uart1", NOMADIK_UART1_BASE, SZ_4K, IRQ_UART1, 0, NULL, 0);
340 i2c_register_board_info(0, nhk8815_i2c0_devices,
341 ARRAY_SIZE(nhk8815_i2c0_devices));
342 i2c_register_board_info(1, nhk8815_i2c1_devices,
343 ARRAY_SIZE(nhk8815_i2c1_devices));
344 i2c_register_board_info(2, nhk8815_i2c2_devices,
345 ARRAY_SIZE(nhk8815_i2c2_devices));
348 MACHINE_START(NOMADIK, "NHK8815")
349 /* Maintainer: ST MicroElectronics */
350 .atag_offset = 0x100,
351 .map_io = cpu8815_map_io,
352 .init_irq = cpu8815_init_irq,
353 .handle_irq = vic_handle_irq,
354 .timer = &nomadik_timer,
355 .init_machine = nhk8815_platform_init,
356 .restart = cpu8815_restart,