4 //#include "lcd-b101ew05.dtsi"
5 #include "lcd-F402.dtsi"
6 #include "vtl_ts_sdk8846.dtsi"
7 #include "rk3288-cif-sensor.dtsi"
14 compatible = "wlan-platdata";
16 /* wifi_chip_type - wifi chip define
17 * bcmwifi ==> like ap6xxx, rk90x;
18 * rtkwifi ==> like rtl8188xx, rtl8723xx;
19 * esp8089 ==> esp8089;
20 * other ==> for other wifi;
22 wifi_chip_type = "bcmwifi";
24 sdio_vref = <1800>; //1800mv or 3300mv
29 power_pmu_regulator = "act_ldo3";
30 power_pmu_enable_level = <1>; //1->HIGH, 0->LOW
33 //vref_ctrl_gpio = <&gpio0 GPIO_A2 GPIO_ACTIVE_HIGH>;
34 vref_pmu_regulator = "act_ldo3";
35 vref_pmu_enable_level = <1>; //1->HIGH, 0->LOW
37 WIFI,poweren_gpio = <&gpio4 GPIO_D4 GPIO_ACTIVE_HIGH>;
38 WIFI,host_wake_irq = <&gpio4 GPIO_D6 GPIO_ACTIVE_HIGH>;
39 //WIFI,reset_gpio = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
45 compatible = "bluetooth-platdata";
47 //wifi-bt-power-toggle;
49 uart_rts_gpios = <&gpio4 GPIO_C3 GPIO_ACTIVE_LOW>;
50 pinctrl-names = "default","rts_gpio";
51 pinctrl-0 = <&uart0_rts>;
52 pinctrl-1 = <&uart0_rts_gpio>;
54 BT,power_gpio = <&gpio4 GPIO_D3 GPIO_ACTIVE_HIGH>;
55 BT,reset_gpio = <&gpio4 GPIO_D5 GPIO_ACTIVE_HIGH>;
56 BT,wake_gpio = <&gpio4 GPIO_D2 GPIO_ACTIVE_HIGH>;
57 BT,wake_host_irq = <&gpio4 GPIO_D7 GPIO_ACTIVE_HIGH>;
63 compatible = "hall_och165t";
64 type = <SENSOR_TYPE_HALL>;
65 irq-gpio = <&gpio0 GPIO_A6 IRQ_TYPE_EDGE_BOTH>;
69 compatible = "pwm-backlight";
70 pwms = <&pwm0 0 25000>;
71 brightness-levels = <255 254 253 252 251 250 249 248 247 246 245 244 243 242 241 240
72 239 238 237 236 235 234 233 232 231 230 229 228 227 226 225 224 223 222 221 220
73 219 218 217 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200
74 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180
75 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160
76 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140
77 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120
78 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100
79 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70
80 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40
81 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
83 default-brightness-level = <200>;
84 enable-gpios = <&gpio7 GPIO_A2 GPIO_ACTIVE_HIGH>;
88 compatible = "rockchip_pwm_regulator";
89 pwms = <&pwm1 0 2000>;
91 rockchip,pwm_voltage_map= <925000 950000 975000 1000000 1025000 1050000 1075000 1100000 1125000 1150000 1175000 1200000 1225000 1250000 1275000 1300000 1325000 1350000 1375000 1400000>;
92 rockchip,pwm_voltage= <1000000>;
93 rockchip,pwm_min_voltage= <925000>;
94 rockchip,pwm_max_voltage= <1400000>;
95 rockchip,pwm_suspend_voltage= <950000>;
96 rockchip,pwm_coefficient= <475>;
100 pwm_reg0: regulator@0 {
101 regulator-compatible = "pwm_dcdc1";
102 regulator-name= "vdd_logic";
103 regulator-min-microvolt = <925000>;
104 regulator-max-microvolt = <1400000>;
111 codec_hdmi_i2s: codec-hdmi-i2s {
112 compatible = "hdmi-i2s";
115 codec_hdmi_spdif: codec-hdmi-spdif {
116 compatible = "hdmi-spdif";
120 compatible = "rockchip-hdmi-i2s";
123 audio-codec = <&codec_hdmi_i2s>;
124 i2s-controller = <&i2s>;
127 //bitclock-inversion;
135 rockchip-hdmi-spdif {
136 compatible = "rockchip-hdmi-spdif";
139 audio-codec = <&codec_hdmi_spdif>;
140 i2s-controller = <&spdif>;
146 compatible = "rockchip-rt5631";
149 audio-codec = <&rt5631>;
150 i2s-controller = <&i2s>;
153 //bitclock-inversion;
162 compatible = "rockchip-rt3261";
165 audio-codec = <&rt3261>;
166 i2s-controller = <&i2s>;
169 //bitclock-inversion;
175 audio-codec = <&rt3261>;
176 i2s-controller = <&i2s>;
188 compatible = "rockchip,rk3288-usb-control";
190 host_drv_gpio = <&gpio0 GPIO_B6 GPIO_ACTIVE_LOW>;
191 otg_drv_gpio = <&gpio0 GPIO_B4 GPIO_ACTIVE_LOW>;
193 rockchip,remote_wakeup;
194 rockchip,usb_irq_wakeup;
197 bootargs = "vmalloc=512M";
202 // power_ctl_by = "gpio"; //"gpio" "pmu"
203 power-gpio = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH>;
204 // power-pmu = "act_ldo"
205 // reset-gpio = <&gpio4 GPIO_A7 GPIO_ACTIVE_LOW>;
207 clock_in_out = "input";
210 status = "disabled"; //if want to use gmac, please set "okay"
214 //used for init some gpio
215 init-gpios = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH
216 /*&gpio0 GPIO_C2 GPIO_ACTIVE_HIGH */
217 /*&gpio7 GPIO_B7 GPIO_ACTIVE_LOW */>;
221 rockchip,pins = <GPIO0_C2>;
222 rockchip,pull = <VALUE_PULL_DOWN>;
230 rockchip,pins = <GPIO7_A7>;
231 rockchip,pull = <VALUE_PULL_DOWN>;
237 //could add other pinctrl definition such as gpio
239 // gmac drive strength
242 rockchip,drive = <VALUE_DRV_12MA>;
245 mac_txpins: mac-txpins {
246 rockchip,drive = <VALUE_DRV_12MA>;
249 mac_rxpins: mac-rxpins {
250 rockchip,drive = <VALUE_DRV_12MA>;
254 rockchip,drive = <VALUE_DRV_12MA>;
257 mac_mdpins: mac-mdpins {
258 rockchip,drive = <VALUE_DRV_12MA>;
264 status = "disabled"; // used nand set "disabled" ,used emmc set "okay"
267 status = "disabled"; // used nand set "disabled" ,used emmc set "okay"
271 status = "okay"; // used nand set "disabled" ,used emmc set "okay"
275 clock-frequency = <100000000>;
276 clock-freq-min-max = <400000 100000000>;
283 //supports-DDR_MODE; //you should set the two value in your project. only close in RK3288-SDK board.
287 keep-power-in-suspend;
294 clock-frequency = <50000000>;
295 clock-freq-min-max = <400000 50000000>;
299 card-detect-delay = <200>;
302 keep-power-in-suspend;
304 vmmc-supply = <&ldo1_reg>;
309 clock-frequency = <50000000>;
310 clock-freq-min-max = <200000 50000000>;
314 keep-power-in-suspend;
321 max-freq = <48000000>;
324 compatible = "rockchip,spi_test_bus0_cs0";
326 spi-max-frequency = <24000000>;
336 compatible = "rockchip,spi_test_bus0_cs1";
338 spi-max-frequency = <24000000>;
350 max-freq = <48000000>;
353 compatible = "rockchip,spi_test_bus1_cs0";
355 spi-max-frequency = <24000000>;
368 max-freq = <48000000>;
371 compatible = "rockchip,spi_test_bus2_cs0";
373 spi-max-frequency = <24000000>;
382 compatible = "rockchip,spi_test_bus2_cs1";
384 spi-max-frequency = <24000000>;
396 dma-names = "!tx", "!rx";
397 pinctrl-0 = <&uart0_xfer &uart0_cts>;
411 compatible = "silergy,syr82x";
415 #address-cells = <1>;
417 syr827_dc1: regulator@0 {
419 regulator-compatible = "syr82x_dcdc1";
420 regulator-name = "vdd_arm";
421 regulator-min-microvolt = <712500>;
422 regulator-max-microvolt = <1500000>;
425 regulator-initial-mode = <0x2>;
426 regulator-initial-state = <3>;
427 regulator-state-mem {
428 regulator-state-mode = <0x2>;
429 regulator-state-disabled;
430 regulator-state-uv = <900000>;
436 compatible = "silergy,syr82x";
440 #address-cells = <1>;
442 syr828_dc1: regulator@0 {
444 regulator-compatible = "syr82x_dcdc1";
445 regulator-name = "vdd_gpu";
446 regulator-min-microvolt = <712500>;
447 regulator-max-microvolt = <1500000>;
450 regulator-initial-mode = <0x2>;
451 regulator-initial-state = <3>;
452 regulator-state-mem {
453 regulator-state-mode = <0x2>;
454 regulator-state-enabled;
455 regulator-state-uv = <900000>;
460 act8846: act8846@5a {
465 ricoh619: ricoh619@32 {
469 bq24296: bq24296@6b {
470 compatible = "ti,bq24296";
472 gpios = <&gpio0 GPIO_A7 GPIO_ACTIVE_HIGH>,<&gpio0 GPIO_B0 GPIO_ACTIVE_HIGH>;
473 bq24296,chg_current = <1000 2000 3000>;
477 bq27320: bq27320@55 {
478 compatible = "ti,bq27320";
480 /* gpios = <&gpio0 GPIO_A7 GPIO_ACTIVE_HIGH>; */
485 compatible = "cw201x";
487 dc_det_gpio = <&gpio0 GPIO_B0 GPIO_ACTIVE_LOW>;
488 bat_low_gpio = <&gpio0 GPIO_A7 GPIO_ACTIVE_LOW>;
489 chg_ok_gpio = <&gpio0 GPIO_B1 GPIO_ACTIVE_HIGH>;
490 bat_config_info = <0x15 0x42 0x60 0x59 0x52 0x58 0x4D 0x48 0x48 0x44 0x44 0x46 0x49 0x48 0x32
491 0x24 0x20 0x17 0x13 0x0F 0x19 0x3E 0x51 0x45 0x08 0x76 0x0B 0x85 0x0E 0x1C 0x2E 0x3E 0x4D 0x52 0x52
492 0x57 0x3D 0x1B 0x6A 0x2D 0x25 0x43 0x52 0x87 0x8F 0x91 0x94 0x52 0x82 0x8C 0x92 0x96 0xFF 0x7B 0xBB
493 0xCB 0x2F 0x7D 0x72 0xA5 0xB5 0xC1 0x46 0xAE>;
499 compatible = "rtc,hym8563";
501 irq_gpio = <&gpio0 GPIO_A4 IRQ_TYPE_EDGE_FALLING>;
510 compatible = "mpu6050";
512 mpu-int_config = <0x10>;
513 mpu-level_shifter = <0>;
514 mpu-orientation = <0 1 0 1 0 0 0 0 1>;
518 irq-gpio = <&gpio8 GPIO_A0 IRQ_TYPE_LEVEL_LOW>;
524 compatible = "mpu_ak8963";
527 compass-adapt_num = <0>;
528 compass-orientation = <1 0 0 0 1 0 0 0 1>;
541 compatible = "rt5631";
545 compatible = "es8323";
549 compatible = "rt3261";
551 // codec-en-gpio = <0>;//sdk default high level
553 modem-input-mode = <1>;
554 lout-to-modem_mode = <1>;
556 playback-if1-data_control = <0>;
557 playback-if2-data_control = <0>;
560 compatible = "rt5616";
573 compatible = "ct,vtl_ts";
575 screen_max_x = <1536>;
576 screen_max_y = <2048>;
583 irq_gpio_number = <&gpio7 GPIO_A6 IRQ_TYPE_LEVEL_LOW>;
584 rst_gpio_number = <&gpio7 GPIO_A5 GPIO_ACTIVE_HIGH>;
593 rockchip,disp-mode = <DUAL>;
594 rockchip,uboot-logo-on = <1>;
598 display-timings = <&disp_timings>;
601 /*lcdc0 as PRMRY(LCD),lcdc1 as EXTEND(HDMI)*/
604 rockchip,mirror = <NO_MIRROR>;
605 rockchip,cabc_mode = <0>;
606 power_ctr: power_ctr {
607 rockchip,debug = <0>;
609 rockchip,power_type = <REGULATOR>;
610 rockchip,regulator_name = "vcc_18";
611 rockchip,regulator_voltage = <1800000>;
612 rockchip,delay = <5>;
616 rockchip,power_type = <GPIO>;
617 gpios = <&gpio7 GPIO_A3 GPIO_ACTIVE_HIGH>;
618 rockchip,delay = <10>;
622 rockchip,power_type = <GPIO>;
623 gpios = <&gpio7 GPIO_A4 GPIO_ACTIVE_HIGH>;
624 rockchip,delay = <10>;
628 rockchip,power_type = <GPIO>;
629 gpios = <&gpio3 GPIO_D6 GPIO_ACTIVE_HIGH>;
630 rockchip,delay = <5>;
638 rockchip,mirror = <ROTATE_270>;
644 rockchips,hdmi_audio_source = <0>;
651 compatible = "rockchip_headset";
652 headset_gpio = <&gpio7 GPIO_A7 GPIO_ACTIVE_LOW>;
653 pinctrl-names = "default";
654 pinctrl-0 = <&gpio7_a7>;
655 io-channels = <&adc 2>;
658 hook_down_type = ; //interrupt hook key down status
663 compatible = "rockchip,key";
664 io-channels = <&adc 1>;
669 rockchip,adc_value = <1>;
674 label = "volume down";
675 rockchip,adc_value = <170>;
679 gpios = <&gpio0 GPIO_A5 GPIO_ACTIVE_LOW>;
688 rockchip,adc_value = <355>;
694 rockchip,adc_value = <746>;
700 rockchip,adc_value = <560>;
706 rockchip,adc_value = <450>;
720 &clk_core_dvfs_table {
739 pvtm-operating-points = <
740 /* KHz uV margin(uV)*/
748 1008000 1050000 25000
749 1200000 1100000 25000
750 1416000 1200000 25000
751 1512000 1300000 25000
752 1608000 1350000 25000
757 &clk_gpu_dvfs_table {
769 &clk_ddr_dvfs_table {
780 SYS_STATUS_NORMAL 400000
781 SYS_STATUS_SUSPEND 200000
782 SYS_STATUS_VIDEO_1080P 240000
783 SYS_STATUS_VIDEO_4K 400000
784 SYS_STATUS_PERFORMANCE 528000
785 SYS_STATUS_DUALVIEW 400000
786 SYS_STATUS_BOOST 324000
787 SYS_STATUS_ISP 400000
798 /include/ "act8846.dtsi"
800 gpios =<&gpio7 GPIO_A1 GPIO_ACTIVE_LOW>,<&gpio0 GPIO_B2 GPIO_ACTIVE_HIGH>;
801 act8846,system-power-controller;
805 dcdc1_reg: regulator@0{
806 regulator-name= "act_dcdc1";
807 regulator-min-microvolt = <1200000>;
808 regulator-max-microvolt = <1200000>;
813 dcdc2_reg: regulator@1 {
814 regulator-name= "vccio";
815 regulator-min-microvolt = <3300000>;
816 regulator-max-microvolt = <3300000>;
817 regulator-initial-state = <3>;
818 regulator-state-mem {
819 regulator-state-enabled;
820 regulator-state-uv = <3300000>;
824 dcdc3_reg: regulator@2 {
825 regulator-name= "vdd_logic";
826 regulator-min-microvolt = <700000>;
827 regulator-max-microvolt = <1500000>;
828 regulator-initial-state = <3>;
829 regulator-state-mem {
830 regulator-state-enabled;
831 regulator-state-uv = <1000000>;
836 dcdc4_reg: regulator@3 {
837 regulator-name= "act_dcdc4";
838 regulator-min-microvolt = <2000000>;
839 regulator-max-microvolt = <2000000>;
840 regulator-initial-state = <3>;
841 regulator-state-mem {
842 regulator-state-enabled;
843 regulator-state-uv = <2000000>;
847 ldo1_reg: regulator@4 {
848 regulator-name= "vccio_sd";
849 regulator-min-microvolt = <1800000>;
850 regulator-max-microvolt = <3300000>;
854 ldo2_reg: regulator@5 {
855 regulator-name= "act_ldo2";
856 regulator-min-microvolt = <1000000>;
857 regulator-max-microvolt = <1000000>;
861 ldo3_reg: regulator@6 {
862 regulator-name= "act_ldo3";
863 regulator-min-microvolt = <3300000>;
864 regulator-max-microvolt = <3300000>;
868 ldo4_reg:regulator@7 {
869 regulator-name= "act_ldo4";
870 regulator-min-microvolt = <3300000>;
871 regulator-max-microvolt = <3300000>;
875 ldo5_reg: regulator@8 {
876 regulator-name= "act_ldo5";
877 regulator-min-microvolt = <3300000>;
878 regulator-max-microvolt = <3300000>;
882 ldo6_reg: regulator@9 {
883 regulator-name= "act_ldo6";
884 regulator-min-microvolt = <1000000>;
885 regulator-max-microvolt = <1000000>;
886 regulator-initial-state = <3>;
887 regulator-state-mem {
888 regulator-state-enabled;
893 ldo7_reg: regulator@10 {
894 regulator-name= "vcc_18";
895 regulator-min-microvolt = <1800000>;
896 regulator-max-microvolt = <1800000>;
897 regulator-initial-state = <3>;
898 regulator-state-mem {
899 regulator-state-enabled;
904 ldo8_reg: regulator@11 {
905 regulator-name= "act_ldo8";
906 regulator-min-microvolt = <1800000>;
907 regulator-max-microvolt = <1800000>;
914 /include/ "rk808.dtsi"
916 gpios =<&gpio0 GPIO_A4 GPIO_ACTIVE_HIGH>,<&gpio0 GPIO_B3 GPIO_ACTIVE_LOW>;
917 rk808,system-power-controller;
921 rk808_dcdc1_reg: regulator@0{
922 regulator-name= "vdd_arm";
927 rk808_dcdc2_reg: regulator@1 {
928 regulator-name= "vdd_gpu";
933 rk808_dcdc3_reg: regulator@2 {
934 regulator-name= "rk_dcdc3";
935 regulator-min-microvolt = <1200000>;
936 regulator-max-microvolt = <1200000>;
941 rk808_dcdc4_reg: regulator@3 {
942 regulator-name= "vccio";
943 regulator-min-microvolt = <1800000>;
944 regulator-max-microvolt = <3300000>;
949 rk808_ldo1_reg: regulator@4 {
950 regulator-name= "rk_ldo1";
951 regulator-min-microvolt = <3300000>;
952 regulator-max-microvolt = <3300000>;
957 rk808_ldo2_reg: regulator@5 {
958 regulator-name= "rk_ldo2";
959 regulator-min-microvolt = <3300000>;
960 regulator-max-microvolt = <3300000>;
965 rk808_ldo3_reg: regulator@6 {
966 regulator-name= "rk_ldo3";
967 regulator-min-microvolt = <1000000>;
968 regulator-max-microvolt = <1000000>;
973 rk808_ldo4_reg:regulator@7 {
974 regulator-name= "rk_ldo4";
975 regulator-min-microvolt = <1800000>;
976 regulator-max-microvolt = <1800000>;
981 rk808_ldo5_reg: regulator@8 {
982 regulator-name= "vcc_sd";
983 regulator-min-microvolt = <1800000>;
984 regulator-max-microvolt = <3300000>;
989 rk808_ldo6_reg: regulator@9 {
990 regulator-name= "rk_ldo6";
991 regulator-min-microvolt = <1000000>;
992 regulator-max-microvolt = <1000000>;
997 rk808_ldo7_reg: regulator@10 {
998 regulator-name= "rk_ldo7";
999 regulator-min-microvolt = <1800000>;
1000 regulator-max-microvolt = <1800000>;
1001 regulator-always-on;
1005 rk808_ldo8_reg: regulator@11 {
1006 regulator-name= "rk_ldo8";
1007 regulator-min-microvolt = <3300000>;
1008 regulator-max-microvolt = <3300000>;
1009 regulator-always-on;
1013 rk808_ldo9_reg: regulator@12 {
1014 regulator-name= "rk_ldo9";
1015 regulator-always-on;
1019 rk808_ldo10_reg: regulator@13 {
1020 regulator-name= "rk_ldo10";
1021 regulator-always-on;
1028 regulator-name = "vcc30_lcd";
1031 regulator-name = "vcc18_cif";
1034 regulator-name = "vcc_flash";
1037 regulator-name = "vcc_flash";
1040 regulator-name = "vccio_wl";
1043 regulator-name = "vccio";
1046 regulator-name = "vccio";
1049 regulator-name = "vccio";
1052 regulator-name = "vccio";
1055 regulator-name = "vcc_sd";
1060 status = "disabled";