2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
11 #include <dt-bindings/interrupt-controller/irq.h>
12 #include <dt-bindings/interrupt-controller/arm-gic.h>
15 model = "TI OMAP5 uEVM board";
16 compatible = "ti,omap5-uevm", "ti,omap5";
19 device_type = "memory";
20 reg = <0x80000000 0x7F000000>; /* 2032 MB */
23 vmmcsd_fixed: fixedregulator-mmcsd {
24 compatible = "regulator-fixed";
25 regulator-name = "vmmcsd_fixed";
26 regulator-min-microvolt = <3000000>;
27 regulator-max-microvolt = <3000000>;
30 /* HS USB Host PHY on PORT 2 */
31 hsusb2_phy: hsusb2_phy {
32 compatible = "usb-nop-xceiv";
33 reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
34 clocks = <&auxclk1_ck>;
35 clock-names = "main_clk";
36 clock-frequency = <19200000>;
39 /* HS USB Host PHY on PORT 3 */
40 hsusb3_phy: hsusb3_phy {
41 compatible = "usb-nop-xceiv";
42 reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
46 compatible = "gpio-leds";
48 label = "omap5:blue:usr1";
49 gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
50 linux,default-trigger = "heartbeat";
51 default-state = "off";
57 pinctrl-names = "default";
67 twl6040_pins: pinmux_twl6040_pins {
68 pinctrl-single,pins = <
69 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
73 mcpdm_pins: pinmux_mcpdm_pins {
74 pinctrl-single,pins = <
75 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
76 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */
77 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */
78 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */
79 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */
83 mcbsp1_pins: pinmux_mcbsp1_pins {
84 pinctrl-single,pins = <
85 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
86 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */
87 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */
88 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */
92 mcbsp2_pins: pinmux_mcbsp2_pins {
93 pinctrl-single,pins = <
94 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */
95 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */
96 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */
97 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */
101 i2c1_pins: pinmux_i2c1_pins {
102 pinctrl-single,pins = <
103 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
104 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
108 i2c5_pins: pinmux_i2c5_pins {
109 pinctrl-single,pins = <
110 0x184 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */
111 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */
115 mcspi2_pins: pinmux_mcspi2_pins {
116 pinctrl-single,pins = <
117 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
118 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
119 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
120 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */
124 mcspi3_pins: pinmux_mcspi3_pins {
125 pinctrl-single,pins = <
126 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */
127 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */
128 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */
129 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */
133 mcspi4_pins: pinmux_mcspi4_pins {
134 pinctrl-single,pins = <
135 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi4_clk */
136 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi4_simo */
137 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi4_somi */
138 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi4_cs0 */
142 usbhost_pins: pinmux_usbhost_pins {
143 pinctrl-single,pins = <
144 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
145 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
147 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
148 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
150 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
151 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
155 led_gpio_pins: pinmux_led_gpio_pins {
156 pinctrl-single,pins = <
157 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
161 uart1_pins: pinmux_uart1_pins {
162 pinctrl-single,pins = <
163 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
164 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
165 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
166 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
170 uart3_pins: pinmux_uart3_pins {
171 pinctrl-single,pins = <
172 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
173 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
177 uart5_pins: pinmux_uart5_pins {
178 pinctrl-single,pins = <
179 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
180 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
181 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
182 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
189 pinctrl-names = "default";
194 usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
195 pinctrl-single,pins = <
196 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
202 vmmc-supply = <&ldo9_reg>;
207 vmmc-supply = <&vmmcsd_fixed>;
226 pinctrl-names = "default";
227 pinctrl-0 = <&i2c1_pins>;
229 clock-frequency = <400000>;
232 compatible = "ti,palmas";
233 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
234 interrupt-parent = <&gic>;
236 interrupt-controller;
237 #interrupt-cells = <2>;
238 ti,system-power-controller;
240 extcon_usb3: palmas_usb {
241 compatible = "ti,palmas-usb-vid";
242 ti,enable-vbus-detection;
243 ti,enable-id-detection;
248 compatible = "ti,palmas-pmic";
249 interrupt-parent = <&palmas>;
250 interrupts = <14 IRQ_TYPE_NONE>;
251 interrupt-name = "short-irq";
256 smps123_reg: smps123 {
258 regulator-name = "smps123";
259 regulator-min-microvolt = < 600000>;
260 regulator-max-microvolt = <1500000>;
267 regulator-name = "smps45";
268 regulator-min-microvolt = < 600000>;
269 regulator-max-microvolt = <1310000>;
275 /* VDD_DDR3 - over VDD_SMPS6 */
276 regulator-name = "smps6";
277 regulator-min-microvolt = <1200000>;
278 regulator-max-microvolt = <1200000>;
284 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
285 regulator-name = "smps7";
286 regulator-min-microvolt = <1800000>;
287 regulator-max-microvolt = <1800000>;
294 regulator-name = "smps8";
295 regulator-min-microvolt = < 600000>;
296 regulator-max-microvolt = <1310000>;
302 /* VDDA_2v1_AUD over VDD_2v1 */
303 regulator-name = "smps9";
304 regulator-min-microvolt = <2100000>;
305 regulator-max-microvolt = <2100000>;
306 ti,smps-range = <0x80>;
309 smps10_out2_reg: smps10_out2 {
311 regulator-name = "smps10_out2";
312 regulator-min-microvolt = <5000000>;
313 regulator-max-microvolt = <5000000>;
318 smps10_out1_reg: smps10_out1 {
320 regulator-name = "smps10_out1";
321 regulator-min-microvolt = <5000000>;
322 regulator-max-microvolt = <5000000>;
326 /* VDDAPHY_CAM: vdda_csiport */
327 regulator-name = "ldo1";
328 regulator-min-microvolt = <1500000>;
329 regulator-max-microvolt = <1800000>;
333 /* VCC_2V8_DISP: Does not go anywhere */
334 regulator-name = "ldo2";
335 regulator-min-microvolt = <2800000>;
336 regulator-max-microvolt = <2800000>;
342 /* VDDAPHY_MDM: vdda_lli */
343 regulator-name = "ldo3";
344 regulator-min-microvolt = <1500000>;
345 regulator-max-microvolt = <1500000>;
347 /* Only if Modem is used */
352 /* VDDAPHY_DISP: vdda_dsiport/hdmi */
353 regulator-name = "ldo4";
354 regulator-min-microvolt = <1500000>;
355 regulator-max-microvolt = <1800000>;
359 /* VDDA_1V8_PHY: usb/sata/hdmi.. */
360 regulator-name = "ldo5";
361 regulator-min-microvolt = <1800000>;
362 regulator-max-microvolt = <1800000>;
368 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
369 regulator-name = "ldo6";
370 regulator-min-microvolt = <1200000>;
371 regulator-max-microvolt = <1200000>;
378 regulator-name = "ldo7";
379 regulator-min-microvolt = <2000000>;
380 regulator-max-microvolt = <2000000>;
381 /* Only for efuse reprograming! */
386 /* VDD_3v0: Does not go anywhere */
387 regulator-name = "ldo8";
388 regulator-min-microvolt = <3000000>;
389 regulator-max-microvolt = <3000000>;
396 /* VCC_DV_SDIO: vdds_sdcard */
397 regulator-name = "ldo9";
398 regulator-min-microvolt = <1800000>;
399 regulator-max-microvolt = <3000000>;
404 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
405 regulator-name = "ldoln";
406 regulator-min-microvolt = <1800000>;
407 regulator-max-microvolt = <1800000>;
413 /* VDDA_3V_USB: VDDA_USBHS33 */
414 regulator-name = "ldousb";
415 regulator-min-microvolt = <3250000>;
416 regulator-max-microvolt = <3250000>;
422 /* REGEN3 controls LDO9 supply to card */
423 regulator-name = "regen3";
433 pinctrl-names = "default";
434 pinctrl-0 = <&i2c5_pins>;
436 clock-frequency = <400000>;
444 port2-mode = "ehci-hsic";
445 port3-mode = "ehci-hsic";
449 phys = <0 &hsusb2_phy &hsusb3_phy>;
453 extcon = <&extcon_usb3>;
454 vbus-supply = <&smps10_out1_reg>;
462 pinctrl-names = "default";
463 pinctrl-0 = <&mcspi2_pins>;
467 pinctrl-names = "default";
468 pinctrl-0 = <&mcspi3_pins>;
472 pinctrl-names = "default";
473 pinctrl-0 = <&mcspi4_pins>;
477 pinctrl-names = "default";
478 pinctrl-0 = <&uart1_pins>;
482 pinctrl-names = "default";
483 pinctrl-0 = <&uart3_pins>;
487 pinctrl-names = "default";
488 pinctrl-0 = <&uart5_pins>;
492 cpu0-supply = <&smps123_reg>;