2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
10 #include "omap34xx.dtsi"
11 #include "omap-gpmc-smsc911x.dtsi"
14 model = "TI OMAP3430 LDP (Zoom1 Labrador)";
15 compatible = "ti,omap3-ldp", "ti,omap3";
18 device_type = "memory";
19 reg = <0x80000000 0x8000000>; /* 128 MB */
29 compatible = "gpio-keys";
30 pinctrl-names = "default";
31 pinctrl-0 = <&gpio_key_pins>;
35 gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* gpio101 */
36 linux,code = <0x0107001c>; /* KEY_ENTER */
42 gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* gpio102 */
43 linux,code = <0x0303003b>; /* KEY_F1 */
49 gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; /* gpio103 */
50 linux,code = <0x0403003c>; /* KEY_F2 */
56 gpios = <&gpio4 8 GPIO_ACTIVE_LOW>; /* gpio104 */
57 linux,code = <0x0503003d>; /* KEY_F3 */
63 gpios = <&gpio4 9 GPIO_ACTIVE_LOW>; /* gpio105 */
64 linux,code = <0x0704003e>; /* KEY_F4 */
70 gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; /* gpio106 */
71 linux,code = <0x04070069>; /* KEY_LEFT */
77 gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; /* gpio107 */
78 linux,code = <0x0507006a>; /* KEY_RIGHT */
84 gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; /* gpio108 */
85 linux,code = <0x06070067>; /* KEY_UP */
91 gpios = <&gpio4 13 GPIO_ACTIVE_LOW>; /* gpio109 */
92 linux,code = <0x0707006c>; /* KEY_DOWN */
99 ranges = <0 0 0x00000000 0x01000000>,
100 <1 0 0x08000000 0x01000000>;
103 linux,mtd-name= "micron,nand";
105 nand-bus-width = <16>;
106 ti,nand-ecc-opt = "bch8";
108 gpmc,sync-clk-ps = <0>;
110 gpmc,cs-rd-off-ns = <44>;
111 gpmc,cs-wr-off-ns = <44>;
112 gpmc,adv-on-ns = <6>;
113 gpmc,adv-rd-off-ns = <34>;
114 gpmc,adv-wr-off-ns = <44>;
115 gpmc,we-off-ns = <40>;
116 gpmc,oe-off-ns = <54>;
117 gpmc,access-ns = <64>;
118 gpmc,rd-cycle-ns = <82>;
119 gpmc,wr-cycle-ns = <82>;
120 gpmc,wr-access-ns = <40>;
121 gpmc,wr-data-mux-bus-ns = <0>;
123 #address-cells = <1>;
132 reg = <0x80000 0x140000>;
135 label = "Environment";
136 reg = <0x1c0000 0x40000>;
140 reg = <0x200000 0x1e00000>;
143 label = "Filesystem";
144 reg = <0x2000000 0xe000000>;
149 interrupt-parent = <&gpio5>;
150 interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
156 clock-frequency = <2600000>;
160 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
161 interrupt-parent = <&intc>;
164 compatible = "ti,twl4030-power-idle";
170 #include "twl4030.dtsi"
171 #include "twl4030_omap3.dtsi"
172 #include "omap3-panel-sharp-ls037v7dw01.dtsi"
175 gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
179 clock-frequency = <400000>;
183 clock-frequency = <400000>;
186 /* tps61130rsa enabled by twl4030 regen */
192 enable-gpios = <&twl_gpio 15 GPIO_ACTIVE_HIGH>; /* lcd INI */
193 reset-gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>; /* gpio55, lcd RESB */
194 mode-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; /* gpio56, lcd MO */
199 interrupt-parent = <&gpio2>;
200 interrupts = <22 0>; /* gpio54 */
201 pendown-gpio = <&gpio2 22 0>;
206 /* See 35xx errata 2.1.1.128 in SPRZ278F */
207 compatible = "ti,omap3-pre-es3-hsmmc";
208 vmmc-supply = <&vmmc1>;
210 pinctrl-names = "default";
211 pinctrl-0 = <&mmc1_pins>;
223 gpio_key_pins: pinmux_gpio_key_pins {
224 pinctrl-single,pins = <
225 0xea (PIN_INPUT | MUX_MODE4) /* cam_d2.gpio_101 */
226 0xec (PIN_INPUT | MUX_MODE4) /* cam_d3.gpio_102 */
227 0xee (PIN_INPUT | MUX_MODE4) /* cam_d4.gpio_103 */
228 0xf0 (PIN_INPUT | MUX_MODE4) /* cam_d5.gpio_104 */
229 0xf2 (PIN_INPUT | MUX_MODE4) /* cam_d6.gpio_105 */
230 0xf4 (PIN_INPUT | MUX_MODE4) /* cam_d7.gpio_106 */
231 0xf6 (PIN_INPUT | MUX_MODE4) /* cam_d8.gpio_107 */
232 0xf8 (PIN_INPUT | MUX_MODE4) /* cam_d9.gpio_108 */
233 0xfa (PIN_INPUT | MUX_MODE4) /* cam_d10.gpio_109 */
237 musb_pins: pinmux_musb_pins {
238 pinctrl-single,pins = <
239 0x172 (PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
240 0x17a (PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
241 0x17c (PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
242 0x17e (PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
243 0x180 (PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
244 0x182 (PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
245 0x184 (PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
246 0x186 (PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
247 0x188 (PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
248 0x176 (PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
249 0x178 (PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
250 0x174 (PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
254 mmc1_pins: pinmux_mmc1_pins {
255 pinctrl-single,pins = <
256 OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.mmc1_clk */
257 OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.mmc1_cmd */
258 OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.mmc1_dat0 */
259 OMAP3_CORE1_IOPAD(0x214A, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.mmc1_dat1 */
260 OMAP3_CORE1_IOPAD(0x214C, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.mmc1_dat2 */
261 OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.mmc1_dat3 */
267 interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
271 pinctrl-names = "default";
272 pinctrl-0 = <&musb_pins>;
273 interface-type = <0>;
274 usb-phy = <&usb2_phy>;
280 /* Needed for ads7846 */
281 regulator-name = "vcc";