4 The following is a consolidated list of the kernel parameters as implemented
5 (mostly) by the __setup() macro and sorted into English Dictionary order
6 (defined as ignoring all punctuation and sorting digits before letters in a
7 case insensitive manner), and with descriptions where known.
9 Module parameters for loadable modules are specified only as the
10 parameter name with optional '=' and value as appropriate, such as:
12 modprobe usbcore blinkenlights=1
14 Module parameters for modules that are built into the kernel image
15 are specified on the kernel command line with the module name plus
16 '.' plus parameter name, with '=' and value if appropriate, such as:
18 usbcore.blinkenlights=1
20 Hyphens (dashes) and underscores are equivalent in parameter names, so
21 log_buf_len=1M print-fatal-signals=1
22 can also be entered as
23 log-buf-len=1M print_fatal_signals=1
26 This document may not be entirely up to date and comprehensive. The command
27 "modinfo -p ${modulename}" shows a current list of all parameters of a loadable
28 module. Loadable modules, after being loaded into the running kernel, also
29 reveal their parameters in /sys/module/${modulename}/parameters/. Some of these
30 parameters may be changed at runtime by the command
31 "echo -n ${value} > /sys/module/${modulename}/parameters/${parm}".
33 The parameters listed below are only valid if certain kernel build options were
34 enabled and if respective hardware is present. The text in square brackets at
35 the beginning of each description states the restrictions within which a
36 parameter is applicable:
38 ACPI ACPI support is enabled.
39 AGP AGP (Accelerated Graphics Port) is enabled.
40 ALSA ALSA sound support is enabled.
41 APIC APIC support is enabled.
42 APM Advanced Power Management support is enabled.
43 AVR32 AVR32 architecture is enabled.
44 AX25 Appropriate AX.25 support is enabled.
45 BLACKFIN Blackfin architecture is enabled.
46 DRM Direct Rendering Management support is enabled.
47 EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
48 EFI EFI Partitioning (GPT) is enabled
49 EIDE EIDE/ATAPI support is enabled.
50 FB The frame buffer device is enabled.
51 GCOV GCOV profiling is enabled.
52 HW Appropriate hardware is enabled.
53 IA-64 IA-64 architecture is enabled.
54 IMA Integrity measurement architecture is enabled.
55 IOSCHED More than one I/O scheduler is enabled.
56 IP_PNP IP DHCP, BOOTP, or RARP is enabled.
57 ISAPNP ISA PnP code is enabled.
58 ISDN Appropriate ISDN support is enabled.
59 JOY Appropriate joystick support is enabled.
60 KVM Kernel Virtual Machine support is enabled.
61 LIBATA Libata driver is enabled
62 LP Printer support is enabled.
63 LOOP Loopback device support is enabled.
64 M68k M68k architecture is enabled.
65 These options have more detailed description inside of
66 Documentation/m68k/kernel-options.txt.
67 MCA MCA bus support is enabled.
68 MDA MDA console support is enabled.
69 MOUSE Appropriate mouse support is enabled.
70 MSI Message Signaled Interrupts (PCI).
71 MTD MTD (Memory Technology Device) support is enabled.
72 NET Appropriate network support is enabled.
73 NUMA NUMA support is enabled.
74 GENERIC_TIME The generic timeofday code is enabled.
75 NFS Appropriate NFS support is enabled.
76 OSS OSS sound support is enabled.
77 PV_OPS A paravirtualized kernel is enabled.
78 PARIDE The ParIDE (parallel port IDE) subsystem is enabled.
79 PARISC The PA-RISC architecture is enabled.
80 PCI PCI bus support is enabled.
81 PCIE PCI Express support is enabled.
82 PCMCIA The PCMCIA subsystem is enabled.
83 PNP Plug & Play support is enabled.
84 PPC PowerPC architecture is enabled.
85 PPT Parallel port support is enabled.
86 PS2 Appropriate PS/2 support is enabled.
87 RAM RAM disk support is enabled.
88 ROOTPLUG The example Root Plug LSM is enabled.
89 S390 S390 architecture is enabled.
90 SCSI Appropriate SCSI support is enabled.
91 A lot of drivers has their options described inside of
93 SECURITY Different security models are enabled.
94 SELINUX SELinux support is enabled.
95 SERIAL Serial support is enabled.
96 SH SuperH architecture is enabled.
97 SMP The kernel is an SMP kernel.
98 SPARC Sparc architecture is enabled.
99 SWSUSP Software suspend (hibernation) is enabled.
100 SUSPEND System suspend states are enabled.
101 FTRACE Function tracing enabled.
102 TS Appropriate touchscreen support is enabled.
103 UMS USB Mass Storage support is enabled.
104 USB USB support is enabled.
105 USBHID USB Human Interface Device support is enabled.
106 V4L Video For Linux support is enabled.
107 VGA The VGA console has been enabled.
108 VT Virtual terminal support is enabled.
109 WDT Watchdog support is enabled.
110 XT IBM PC/XT MFM hard disk support is enabled.
111 X86-32 X86-32, aka i386 architecture is enabled.
112 X86-64 X86-64 architecture is enabled.
113 More X86-64 boot options can be found in
114 Documentation/x86/x86_64/boot-options.txt .
115 X86 Either 32bit or 64bit x86 (same as X86-32+X86-64)
117 In addition, the following text indicates that the option:
119 BUGS= Relates to possible processor bugs on the said processor.
120 KNL Is a kernel start-up parameter.
121 BOOT Is a boot loader parameter.
123 Parameters denoted with BOOT are actually interpreted by the boot
124 loader, and have no meaning to the kernel directly.
125 Do not modify the syntax of boot loader parameters without extreme
126 need or coordination with <Documentation/x86/boot.txt>.
128 There are also arch-specific kernel-parameters not documented here.
129 See for example <Documentation/x86/x86_64/boot-options.txt>.
131 Note that ALL kernel parameters listed below are CASE SENSITIVE, and that
132 a trailing = on the name of any parameter states that that parameter will
133 be entered as an environment variable, whereas its absence indicates that
134 it will appear as a kernel argument readable via /proc/cmdline by programs
135 running once the system is up.
137 The number of kernel parameters is not limited, but the length of the
138 complete command line (parameters including spaces etc.) is limited to
139 a fixed number of characters. This limit depends on the architecture
140 and is between 256 and 4096 characters. It is defined in the file
141 ./include/asm/setup.h as COMMAND_LINE_SIZE.
145 Advanced Configuration and Power Interface
146 Format: { force | off | ht | strict | noirq | rsdt }
147 force -- enable ACPI if default was off
148 off -- disable ACPI if default was on
149 noirq -- do not use ACPI for IRQ routing
150 ht -- run only enough ACPI to enable Hyper Threading
151 strict -- Be less tolerant of platforms that are not
152 strictly ACPI specification compliant.
153 rsdt -- prefer RSDT over (default) XSDT
155 See also Documentation/power/pm.txt, pci=noacpi
157 acpi_apic_instance= [ACPI, IOAPIC]
159 2: use 2nd APIC table, if available
160 1,0: use 1st APIC table
163 acpi_backlight= [HW,ACPI]
164 acpi_backlight=vendor
166 If set to vendor, prefer vendor specific driver
167 (e.g. thinkpad_acpi, sony_acpi, etc.) instead
168 of the ACPI video.ko driver.
170 acpi.debug_layer= [HW,ACPI,ACPI_DEBUG]
171 acpi.debug_level= [HW,ACPI,ACPI_DEBUG]
173 CONFIG_ACPI_DEBUG must be enabled to produce any ACPI
174 debug output. Bits in debug_layer correspond to a
175 _COMPONENT in an ACPI source file, e.g.,
176 #define _COMPONENT ACPI_PCI_COMPONENT
177 Bits in debug_level correspond to a level in
178 ACPI_DEBUG_PRINT statements, e.g.,
179 ACPI_DEBUG_PRINT((ACPI_DB_INFO, ...
180 The debug_level mask defaults to "info". See
181 Documentation/acpi/debug.txt for more information about
182 debug layers and levels.
184 Enable processor driver info messages:
185 acpi.debug_layer=0x20000000
186 Enable PCI/PCI interrupt routing info messages:
187 acpi.debug_layer=0x400000
188 Enable AML "Debug" output, i.e., stores to the Debug
189 object while interpreting AML:
190 acpi.debug_layer=0xffffffff acpi.debug_level=0x2
191 Enable all messages related to ACPI hardware:
192 acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
194 Some values produce so much output that the system is
195 unusable. The "log_buf_len" parameter may be useful
196 if you need to capture more output.
198 acpi_display_output= [HW,ACPI]
199 acpi_display_output=vendor
200 acpi_display_output=video
203 acpi_irq_balance [HW,ACPI]
204 ACPI will balance active IRQs
207 acpi_irq_nobalance [HW,ACPI]
208 ACPI will not move active IRQs (default)
211 acpi_irq_isa= [HW,ACPI] If irq_balance, mark listed IRQs used by ISA
212 Format: <irq>,<irq>...
214 acpi_irq_pci= [HW,ACPI] If irq_balance, clear listed IRQs for
216 Format: <irq>,<irq>...
218 acpi_no_auto_ssdt [HW,ACPI] Disable automatic loading of SSDT
220 acpi_os_name= [HW,ACPI] Tell ACPI BIOS the name of the OS
221 Format: To spoof as Windows 98: ="Microsoft Windows"
223 acpi_osi= [HW,ACPI] Modify list of supported OS interface strings
224 acpi_osi="string1" # add string1 -- only one string
225 acpi_osi="!string2" # remove built-in string2
226 acpi_osi= # disable all strings
229 Override the pmtimer bug detection: force the kernel
230 to assume that this machine's pmtimer latches its value
231 and always returns good values.
233 acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
234 Format: { level | edge | high | low }
236 acpi_serialize [HW,ACPI] force serialization of AML methods
238 acpi_skip_timer_override [HW,ACPI]
239 Recognize and ignore IRQ0/pin2 Interrupt Override.
240 For broken nForce2 BIOS resulting in XT-PIC timer.
242 acpi_sleep= [HW,ACPI] Sleep options
243 Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
244 old_ordering, s4_nonvs, sci_force_enable }
245 See Documentation/power/video.txt for information on
247 s3_beep is for debugging; it makes the PC's speaker beep
248 as soon as the kernel's real-mode entry point is called.
249 s4_nohwsig prevents ACPI hardware signature from being
250 used during resume from hibernation.
251 old_ordering causes the ACPI 1.0 ordering of the _PTS
252 control method, with respect to putting devices into
253 low power states, to be enforced (the ACPI 2.0 ordering
254 of _PTS is used by default).
255 s4_nonvs prevents the kernel from saving/restoring the
256 ACPI NVS memory during hibernation.
257 sci_force_enable causes the kernel to set SCI_EN directly
258 on resume from S1/S3 (which is against the ACPI spec,
259 but some broken systems don't work without it).
261 acpi_use_timer_override [HW,ACPI]
262 Use timer override. For some broken Nvidia NF5 boards
263 that require a timer override, but don't have HPET
265 acpi_enforce_resources= [ACPI]
266 { strict | lax | no }
267 Check for resource conflicts between native drivers
268 and ACPI OperationRegions (SystemIO and SystemMemory
269 only). IO ports and memory declared in ACPI might be
270 used by the ACPI subsystem in arbitrary AML code and
271 can interfere with legacy drivers.
272 strict (default): access to resources claimed by ACPI
273 is denied; legacy drivers trying to access reserved
274 resources will fail to bind to device using them.
275 lax: access to resources claimed by ACPI is allowed;
276 legacy drivers trying to access reserved resources
277 will bind successfully but a warning message is logged.
278 no: ACPI OperationRegions are not marked as reserved,
279 no further checks are performed.
282 Format: <io>,<irq>,<dma>,<dma2>,<type>
284 add_efi_memmap [EFI; X86] Include EFI memory map in
285 kernel's map of available physical RAM.
288 See header of drivers/scsi/advansys.c.
290 advwdt= [HW,WDT] Advantech WDT
291 Format: <iostart>,<iostop>
293 aedsp16= [HW,OSS] Audio Excel DSP 16
294 Format: <io>,<irq>,<dma>,<mss_io>,<mpu_io>,<mpu_irq>
295 See also header of sound/oss/aedsp16.c.
298 { off | try_unsupported }
299 off: disable AGP support
300 try_unsupported: try to drive unsupported chipsets
301 (may crash computer or cause data corruption)
304 See Documentation/scsi/aha152x.txt.
307 Format: <portbase>[,<buson>,<busoff>[,<dmaspeed>]]
310 See Documentation/scsi/aic7xxx.txt.
313 See Documentation/scsi/aic79xx.txt.
315 amd_iommu= [HW,X86-84]
316 Pass parameters to the AMD IOMMU driver in the system.
318 isolate - enable device isolation (each device, as far
319 as possible, will get its own protection
321 share - put every device behind one IOMMU into the
322 same protection domain
323 fullflush - enable flushing of IO/TLB entries when
324 they are unmapped. Otherwise they are
325 flushed before they will be reused, which
328 amijoy.map= [HW,JOY] Amiga joystick support
329 Map of devices attached to JOY0DAT and JOY1DAT
331 See also Documentation/kernel/input/joystick.txt
333 analog.map= [HW,JOY] Analog joystick and gamepad support
334 Specifies type or capabilities of an analog joystick
335 connected to one of 16 gameports
336 Format: <type1>,<type2>,..<type16>
339 Power management functions (SPARCstation-4/5 + deriv.)
341 Disable APC CPU standby support. SPARCstation-Fox does
342 not play well with APC CPU idle - disable it if you have
343 APC and your system crashes randomly.
345 apic= [APIC,X86-32] Advanced Programmable Interrupt Controller
346 Change the output verbosity whilst booting
347 Format: { quiet (default) | verbose | debug }
348 Change the amount of debugging information output
349 when initialising the APIC and IO-APIC components.
351 apm= [APM] Advanced Power Management
352 See header of arch/x86/kernel/apm_32.c.
354 arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards
355 Format: <io>,<irq>,<nodeID>
359 atarimouse= [HW,MOUSE] Atari Mouse
361 atascsi= [HW,SCSI] Atari SCSI
363 atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess,
364 EzKey and similar keyboards
366 atkbd.reset= [HW] Reset keyboard during initialization
368 atkbd.set= [HW] Select keyboard code set
369 Format: <int> (2 = AT (default), 3 = PS/2)
371 atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar
374 atkbd.softraw= [HW] Choose between synthetic and real raw mode
375 Format: <bool> (0 = real, 1 = synthetic (default))
377 atkbd.softrepeat= [HW]
378 Use software keyboard repeat
382 baycom_epp= [HW,AX25]
385 baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem
387 See header of drivers/net/hamradio/baycom_par.c.
389 baycom_ser_fdx= [HW,AX25]
390 BayCom Serial Port AX.25 Modem (Full Duplex Mode)
391 Format: <io>,<irq>,<mode>[,<baud>]
392 See header of drivers/net/hamradio/baycom_ser_fdx.c.
394 baycom_ser_hdx= [HW,AX25]
395 BayCom Serial Port AX.25 Modem (Half Duplex Mode)
396 Format: <io>,<irq>,<mode>
397 See header of drivers/net/hamradio/baycom_ser_hdx.c.
399 boot_delay= Milliseconds to delay each printk during boot.
400 Values larger than 10 seconds (10000) are changed to
404 bootmem_debug [KNL] Enable bootmem allocator debug messages.
406 bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
407 bttv.radio= Most important insmod options are available as
409 bttv.pll= See Documentation/video4linux/bttv/Insmod-options
410 bttv.tuner= and Documentation/video4linux/bttv/CARDLIST
413 See drivers/scsi/BusLogic.c, comment before function
414 BusLogic_ParseDriverOptions().
416 c101= [NET] Moxa C101 synchronous serial card
418 cachesize= [BUGS=X86-32] Override level 2 CPU cache size detection.
419 Sometimes CPU hardware bugs make them report the cache
420 size incorrectly. The kernel will attempt work arounds
421 to fix known problems, but for some CPUs it is not
422 possible to determine what the correct size should be.
423 This option provides an override for these situations.
426 [SECURITY] Disable capabilities. This would normally
427 be used only if an alternative security model is to be
428 configured. Potentially dangerous and should only be
429 used if you are entirely sure of the consequences.
431 ccw_timeout_log [S390]
432 See Documentation/s390/CommonIO for details.
434 cgroup_disable= [KNL] Disable a particular controller
435 Format: {name of the controller(s) to disable}
436 {Currently supported controllers - "memory"}
438 checkreqprot [SELINUX] Set initial checkreqprot flag value.
439 Format: { "0" | "1" }
440 See security/selinux/Kconfig help text.
441 0 -- check protection applied by kernel (includes
442 any implied execute protection).
443 1 -- check protection requested by application.
444 Default value is set via a kernel config option.
445 Value can be changed at runtime via
446 /selinux/checkreqprot.
449 See Documentation/s390/CommonIO for details.
451 clock= [BUGS=X86-32, HW] gettimeofday clocksource override.
453 Forces specified clocksource (if available) to be used
454 when calculating gettimeofday(). If specified
455 clocksource is not available, it defaults to PIT.
456 Format: { pit | tsc | cyclone | pmtmr }
458 clocksource= [GENERIC_TIME] Override the default clocksource
460 Override the default clocksource and use the clocksource
461 with the name specified.
462 Some clocksource names to choose from, depending on
464 [all] jiffies (this is the base, fallback clocksource)
466 [ARM] imx_timer1,OSTS,netx_timer,mpu_timer2,
467 pxa_timer,timer3,32k_counter,timer0_1
469 [X86-32] pit,hpet,tsc,vmi-timer;
470 scx200_hrt on Geode; cyclone on IBM x440
478 clearcpuid=BITNUM [X86]
479 Disable CPUID feature X for the kernel. See
480 arch/x86/include/asm/cpufeature.h for the valid bit
481 numbers. Note the Linux specific bits are not necessarily
482 stable over kernel options, but the vendor specific
484 Also note that user programs calling CPUID directly
485 or using the feature without checking anything
486 will still see it. This just prevents it from
487 being used by the kernel or shown in /proc/cpuinfo.
488 Also note the kernel might malfunction if you disable
491 cmo_free_hint= [PPC] Format: { yes | no }
492 Specify whether pages are marked as being inactive
493 when they are freed. This is used in CMO environments
494 to determine OS memory pressure for page stealing by
498 code_bytes [X86] How many bytes of object code to print
503 com20020= [HW,NET] ARCnet - COM20020 chipset
505 <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]]
507 com90io= [HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers)
511 ARCnet - COM90xx chipset (memory-mapped buffers)
512 Format: <io>[,<irq>[,<memstart>]]
514 condev= [HW,S390] console device
517 console= [KNL] Output console device and options.
519 tty<n> Use the virtual console device <n>.
523 Use the specified serial port. The options are of
524 the form "bbbbpnf", where "bbbb" is the baud rate,
525 "p" is parity ("n", "o", or "e"), "n" is number of
526 bits, and "f" is flow control ("r" for RTS or
527 omit it). Default is "9600n8".
529 See Documentation/serial-console.txt for more
531 Documentation/networking/netconsole.txt for an
534 uart[8250],io,<addr>[,options]
535 uart[8250],mmio,<addr>[,options]
536 Start an early, polled-mode console on the 8250/16550
537 UART at the specified I/O port or MMIO address,
538 switching to the matching ttyS device later. The
539 options are the same as for ttyS, above.
541 If the device connected to the port is not a TTY but a braille
542 device, prepend "brl," before the device type, for instance
544 For now, only VisioBraille is supported.
546 consoleblank= [KNL] The console blank (screen saver) timeout in
547 seconds. Defaults to 10*60 = 10mins. A value of 0
548 disables the blank timer.
551 [KNL] Change the default value for
552 /proc/<pid>/coredump_filter.
553 See also Documentation/filesystems/proc.txt.
555 cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
557 <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
559 crashkernel=nn[KMG]@ss[KMG]
560 [KNL] Reserve a chunk of physical memory to
561 hold a kernel to switch to with kexec on panic.
563 crashkernel=range1:size1[,range2:size2,...][@offset]
564 [KNL] Same as above, but depends on the memory
565 in the running system. The syntax of range is
566 start-[end] where start and end are both
567 a memory unit (amount[KMG]). See also
568 Documentation/kdump/kdump.txt for a example.
573 cs89x0_media= [HW,NET]
574 Format: { rj45 | aui | bnc }
577 See header of drivers/s390/block/dasd_devmap.c.
579 db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port
580 (one device per port)
581 Format: <port#>,<type>
582 See also Documentation/input/joystick-parport.txt
584 debug [KNL] Enable kernel debugging (events log level).
587 [KNL] verbose self-tests
589 Print debugging info while doing the locking API
591 We default to 0 (no extra messages), setting it to
592 1 will print _a lot_ more information - normally
593 only useful to kernel developers.
595 debug_objects [KNL] Enable object debugging
598 [KNL] Disable object debugging
600 debugpat [X86] Enable PAT debugging
602 decnet.addr= [HW,NET]
603 Format: <area>[,<node>]
604 See also Documentation/networking/decnet.txt.
607 [same as hugepagesz=] The size of the default
608 HugeTLB page size. This is the size represented by
609 the legacy /proc/ hugepages APIs, used for SHM, and
610 default size when mounting hugetlbfs filesystems.
611 Defaults to the default architecture's huge page size
615 Set number of hash buckets for dentry cache.
618 IO parameters + enable/disable command.
620 digiepca= [HW,SERIAL]
621 See drivers/char/README.epca and
622 Documentation/serial/digiepca.txt.
624 disable_mtrr_cleanup [X86]
625 The kernel tries to adjust MTRR layout from continuous
626 to discrete, to make X server driver able to add WB
627 entry later. This parameter disables that.
629 disable_mtrr_trim [X86, Intel and AMD only]
630 By default the kernel will trim any uncacheable
631 memory out of your available memory pool based on
632 MTRR settings. This parameter disables that behavior,
633 possibly causing your machine to run very slowly.
635 disable_timer_pin_1 [X86]
636 Disable PIN 1 of APIC timer
637 Can be useful to work around chipset bugs.
639 dmasound= [HW,OSS] Sound subsystem buffers
641 dma_debug=off If the kernel is compiled with DMA_API_DEBUG support,
642 this option disables the debugging code at boot.
644 dma_debug_entries=<number>
645 This option allows to tune the number of preallocated
646 entries for DMA-API debugging code. One entry is
647 required per DMA-API allocation. Use this if the
648 DMA-API debugging code disables itself because the
649 architectural default is too low.
651 dma_debug_driver=<driver_name>
652 With this option the DMA-API debugging driver
653 filter feature can be enabled at boot time. Just
654 pass the driver to filter for as the parameter.
655 The filter can be disabled or changed to another
656 driver later using sysfs.
662 dynamic_printk Enables pr_debug()/dev_dbg() calls if
663 CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
664 These can also be switched on/off via
665 <debugfs>/dynamic_printk/modules
667 earlycon= [KNL] Output early console device and options.
668 uart[8250],io,<addr>[,options]
669 uart[8250],mmio,<addr>[,options]
670 Start an early, polled-mode console on the 8250/16550
671 UART at the specified I/O port or MMIO address.
672 The options are the same as for ttyS, above.
674 earlyprintk= [X86,SH,BLACKFIN]
676 earlyprintk=serial[,ttySn[,baudrate]]
677 earlyprintk=ttySn[,baudrate]
678 earlyprintk=dbgp[debugController#]
680 Append ",keep" to not disable it when the real console
683 Only vga or serial or usb debug port at a time.
685 Currently only ttyS0 and ttyS1 are supported.
687 Interaction with the standard serial driver is not
690 The VGA output is eventually overwritten by the real
696 Format: {"off" | "on" | "skip[mbr]"}
698 eisa_irq_edge= [PARISC,HW]
699 See header of drivers/parisc/eisa.c.
702 See comment before function elanfreq_setup() in
703 arch/x86/kernel/cpu/cpufreq/elanfreq.c.
706 Format: {"anticipatory" | "cfq" | "deadline" | "noop"}
707 See Documentation/block/as-iosched.txt and
708 Documentation/block/deadline-iosched.txt for details.
710 elfcorehdr= [IA64,PPC,SH,X86]
711 Specifies physical address of start of kernel core
712 image elf header. Generally kexec loader will
713 pass this option to capture kernel.
714 See Documentation/kdump/kdump.txt for details.
716 enable_mtrr_cleanup [X86]
717 The kernel tries to adjust MTRR layout from continuous
718 to discrete, to make X server driver able to add WB
719 entry later. This parameter enables that.
721 enable_timer_pin_1 [X86]
722 Enable PIN 1 of APIC timer
723 Can be useful to work around chipset bugs
724 (in particular on some ATI chipsets).
725 The kernel tries to set a reasonable default.
727 enforcing [SELINUX] Set initial enforcing status.
729 See security/selinux/Kconfig help text.
730 0 -- permissive (log only, no denials).
731 1 -- enforcing (deny and log).
733 Value can be changed at runtime via /selinux/enforce.
735 ether= [HW,NET] Ethernet cards parameters
736 This option is obsoleted by the "netdev=" option, which
737 has equivalent usage. See its documentation for details.
739 eurwdt= [HW,WDT] Eurotech CPU-1220/1410 onboard watchdog.
744 fail_make_request=[KNL]
745 General fault injection mechanism.
746 Format: <interval>,<probability>,<space>,<times>
747 See also /Documentation/fault-injection/.
750 See header of drivers/scsi/fd_mcs.c.
753 See header of drivers/scsi/fdomain.c.
756 See Documentation/blockdev/floppy.txt.
758 force_pal_cache_flush
759 [IA-64] Avoid check_sal_cache_flush which may hang on
760 buggy SAL_CACHE_FLUSH implementations. Using this
761 parameter will force ia64_sal_cache_flush to call
762 ia64_pal_cache_flush instead of SAL_CACHE_FLUSH.
765 [FTRACE] will set and start the specified tracer
766 as early as possible in order to facilitate early
770 [FTRACE] will dump the trace buffers on oops.
772 ftrace_filter=[function-list]
773 [FTRACE] Limit the functions traced by the function
774 tracer at boot up. function-list is a comma separated
775 list of functions. This list can be changed at run
776 time by the set_ftrace_filter file in the debugfs
779 ftrace_notrace=[function-list]
780 [FTRACE] Do not trace the functions specified in
781 function-list. This list can be changed at run time
782 by the set_ftrace_notrace file in the debugfs
786 [HW,JOY] Multisystem joystick and NES/SNES/PSX pad
787 support via parallel port (up to 5 devices per port)
788 Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5>
789 See also Documentation/input/joystick-parport.txt
793 gart_fix_e820= [X86_64] disable the fix e820 for K8 GART
797 gcov_persist= [GCOV] When non-zero (default), profiling data for
798 kernel modules is saved and remains accessible via
799 debugfs, even when the module is unloaded/reloaded.
800 When zero, profiling data is discarded and associated
801 debugfs files are removed at module unload time.
804 See header of drivers/scsi/gdth.c.
806 gpt [EFI] Forces disk with valid GPT signature but
807 invalid Protective MBR to be treated as GPT.
811 hashdist= [KNL,NUMA] Large hashes allocated during boot
812 are distributed across NUMA nodes. Defaults on
813 for 64bit NUMA, off otherwise.
814 Format: 0 | 1 (for off | on)
816 hcl= [IA-64] SGI's Hardware Graph compatibility layer
818 hd= [EIDE] (E)IDE hard drive subsystem geometry
819 Format: <cyl>,<head>,<sect>
821 highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact
822 size of <nn>. This works even on boxes that have no
823 highmem otherwise. This also works to reduce highmem
824 size on bigger boxes.
826 highres= [KNL] Enable/disable high resolution timer mode.
827 Valid parameters: "on", "off"
831 See Documentation/isdn/README.HiSax.
835 hpet= [X86-32,HPET] option to control HPET usage
836 Format: { enable (default) | disable | force |
838 disable: disable HPET and use PIT instead
839 force: allow force enabled of undocumented chips (ICH4,
841 verbose: show contents of HPET registers during setup
843 hugepages= [HW,X86-32,IA-64] HugeTLB pages to allocate at boot.
844 hugepagesz= [HW,IA-64,PPC,X86-64] The size of the HugeTLB pages.
845 On x86-64 and powerpc, this option can be specified
846 multiple times interleaved with hugepages= to reserve
847 huge pages of different sizes. Valid pages sizes on
848 x86-64 are 2M (when the CPU supports "pse") and 1G
849 (when the CPU supports the "pdpe1gb" cpuinfo flag)
850 Note that 1GB pages can only be allocated at boot time
851 using hugepages= and not freed afterwards.
853 hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC)
854 terminal devices. Valid values: 0..8
855 hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs.
856 If specified, z/VM IUCV HVC accepts connections
857 from listed z/VM user IDs only.
859 i2c_bus= [HW] Override the default board specific I2C bus speed
860 or register an additional I2C bus that is not
861 registered from board initialization code.
865 i8042.debug [HW] Toggle i8042 debug mode
866 i8042.direct [HW] Put keyboard port into non-translated mode
867 i8042.dumbkbd [HW] Pretend that controller can only read data from
868 keyboard and cannot control its state
869 (Don't attempt to blink the leds)
870 i8042.noaux [HW] Don't check for auxiliary (== mouse) port
871 i8042.nokbd [HW] Don't check/create keyboard port
872 i8042.noloop [HW] Disable the AUX Loopback command while probing
874 i8042.nomux [HW] Don't check presence of an active multiplexing
876 i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
879 [HW] Frequency with which keyboard LEDs should blink
880 when kernel panics (default is 0.5 sec)
881 i8042.notimeout [HW] Ignore timeout condition signalled by conroller
882 i8042.reset [HW] Reset the controller during init and cleanup
883 i8042.unlock [HW] Unlock (ignore) the keylock
887 i8k.ignore_dmi [HW] Continue probing hardware even if DMI data
888 indicates that the driver is running on unsupported
890 i8k.force [HW] Activate i8k driver even if SMM BIOS signature
891 does not match list of supported models.
893 [HW] Report power status in /proc/i8k
894 (disabled by default)
895 i8k.restricted [HW] Allow controlling fans only if SYS_ADMIN
898 ibmmcascsi= [HW,MCA,SCSI] IBM MicroChannel SCSI adapter
899 See Documentation/mca.txt.
902 Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]]
904 ide-core.nodma= [HW] (E)IDE subsystem
905 Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc
906 .vlb_clock .pci_clock .noflush .nohpa .noprobe .nowerr
907 .cdrom .chs .ignore_cable are additional options
908 See Documentation/ide/ide.txt.
910 ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
911 Claim all unknown PCI IDE storage controllers.
914 Format: idle=poll, idle=mwait, idle=halt, idle=nomwait
915 Poll forces a polling idle loop that can slightly
916 improve the performance of waking up a idle CPU, but
917 will use a lot of power and make the system run hot.
919 idle=mwait: On systems which support MONITOR/MWAIT but
920 the kernel chose to not use it because it doesn't save
921 as much power as a normal idle loop, use the
922 MONITOR/MWAIT idle loop anyways. Performance should be
923 the same as idle=poll.
924 idle=halt: Halt is forced to be used for CPU idle.
925 In such case C2/C3 won't be used again.
926 idle=nomwait: Disable mwait for CPU C-states
928 ignore_loglevel [KNL]
929 Ignore loglevel setting - this will print /all/
930 kernel messages to the console. Useful for debugging.
933 Set number of hash buckets for inode cache.
936 Format: { "0" | "1" }
937 0 -- integrity auditing messages. (Default)
938 1 -- enable informational integrity auditing messages.
941 Format: { "sha1" | "md5" }
945 Load a policy which meets the needs of the Trusted
946 Computing Base. This means IMA will measure all
947 programs exec'd, files mmap'd for exec, and all files
948 opened for read by uid=0.
951 See header of drivers/scsi/in2000.c.
955 Run specified binary instead of /sbin/init as init
958 initcall_debug [KNL] Trace initcalls as they are executed. Useful
959 for working out where the kernel is dying during
962 initrd= [BOOT] Specify the location of the initial ramdisk
964 inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
967 intel_iommu= [DMAR] Intel IOMMU driver (DMAR) option
969 Enable intel iommu driver.
971 Disable intel iommu driver.
972 igfx_off [Default Off]
973 By default, gfx is mapped as normal device. If a gfx
974 device has a dedicated DMAR unit, the DMAR unit is
975 bypassed by not enabling DMAR with this option. In
976 this case, gfx device will use physical address for
979 With this option iommu will not optimize to look
980 for io virtual address below 32 bit forcing dual
981 address cycle on pci bus for cards supporting greater
982 than 32 bit addressing. The default is to look
983 for translation below 32 bit and if not available
984 then look in the higher range.
986 With this option on every unmap_single operation will
987 result in a hardware IOTLB flush operation as opposed
988 to batching them for performance.
992 iomem= Disable strict checking of access to MMIO memory
993 strict regions from userspace.
1009 io7= [HW] IO7 for Marvel based alpha systems
1010 See comment before marvel_specify_io7 in
1011 arch/alpha/kernel/core_marvel.c.
1013 io_delay= [X86] I/O delay method
1015 Standard port 0x80 based delay
1017 Alternate port 0xed based delay (needed on some systems)
1019 Simple two microseconds delay
1024 See Documentation/filesystems/nfsroot.txt.
1026 ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
1027 See comment before ip2_setup() in
1028 drivers/char/ip2/ip2base.c.
1030 ips= [HW,SCSI] Adaptec / IBM ServeRAID controller
1031 See header of drivers/scsi/ips.c.
1034 When an interrupt is not handled search all handlers
1035 for it. Intended to get systems with badly broken
1039 When an interrupt is not handled search all handlers
1040 for it. Also check all handlers each timer
1041 interrupt. Intended to get systems with badly broken
1045 Format: <RDP>,<reset>,<pci_scan>,<verbosity>
1047 isolcpus= [KNL,SMP] Isolate CPUs from the general scheduler.
1049 <cpu number>,...,<cpu number>
1051 <cpu number>-<cpu number>
1052 (must be a positive range in ascending order)
1054 <cpu number>,...,<cpu number>-<cpu number>
1056 This option can be used to specify one or more CPUs
1057 to isolate from the general SMP balancing and scheduling
1058 algorithms. You can move a process onto or off an
1059 "isolated" CPU via the CPU affinity syscalls or cpuset.
1060 <cpu number> begins at 0 and the maximum value is
1061 "number of CPUs in system - 1".
1063 This option is the preferred way to isolate CPUs. The
1064 alternative -- manually setting the CPU mask of all
1065 tasks in the system -- can cause problems and
1066 suboptimal load balancer performance.
1070 js= [HW,JOY] Analog joystick
1071 See Documentation/input/joystick.txt.
1075 kernelcore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1076 specifies the amount of memory usable by the kernel
1077 for non-movable allocations. The requested amount is
1078 spread evenly throughout all nodes in the system. The
1079 remaining memory in each node is used for Movable
1080 pages. In the event, a node is too small to have both
1081 kernelcore and Movable pages, kernelcore pages will
1082 take priority and other nodes will have a larger number
1083 of kernelcore pages. The Movable zone is used for the
1084 allocation of pages that may be reclaimed or moved
1085 by the page migration subsystem. This means that
1086 HugeTLB pages may not be allocated from this zone.
1087 Note that allocations like PTEs-from-HighMem still
1088 use the HighMem zone if it exists, and the Normal
1089 zone if it does not.
1091 kgdboc= [HW] kgdb over consoles.
1092 Requires a tty driver that supports console polling.
1093 (only serial supported for now)
1094 Format: <serial_device>[,baud]
1096 kmac= [MIPS] korina ethernet MAC address.
1097 Configure the RouterBoard 532 series on-chip
1098 Ethernet adapter MAC address.
1100 kmemleak= [KNL] Boot-time kmemleak enable/disable
1101 Valid arguments: on, off
1104 kstack=N [X86] Print N words from the kernel stack
1107 kvm.ignore_msrs=[KVM] Ignore guest accesses to unhandled MSRs.
1108 Default is 0 (don't ignore, but inject #GP)
1110 kvm.oos_shadow= [KVM] Disable out-of-sync shadow paging.
1111 Default is 1 (enabled)
1113 kvm-amd.nested= [KVM,AMD] Allow nested virtualization in KVM/SVM.
1116 kvm-amd.npt= [KVM,AMD] Disable nested paging (virtualized MMU)
1118 Default is 1 (enabled) if in 64bit or 32bit-PAE mode
1120 kvm-intel.bypass_guest_pf=
1121 [KVM,Intel] Disables bypassing of guest page faults
1122 on Intel chips. Default is 1 (enabled)
1124 kvm-intel.ept= [KVM,Intel] Disable extended page tables
1125 (virtualized MMU) support on capable Intel chips.
1126 Default is 1 (enabled)
1128 kvm-intel.emulate_invalid_guest_state=
1129 [KVM,Intel] Enable emulation of invalid guest states
1130 Default is 0 (disabled)
1132 kvm-intel.flexpriority=
1133 [KVM,Intel] Disable FlexPriority feature (TPR shadow).
1134 Default is 1 (enabled)
1136 kvm-intel.unrestricted_guest=
1137 [KVM,Intel] Disable unrestricted guest feature
1138 (virtualized real and unpaged mode) on capable
1139 Intel chips. Default is 1 (enabled)
1141 kvm-intel.vpid= [KVM,Intel] Disable Virtual Processor Identification
1142 feature (tagged TLBs) on capable Intel chips.
1143 Default is 1 (enabled)
1149 lapic [X86-32,APIC] Enable the local APIC even if BIOS
1152 lapic_timer_c2_ok [X86,APIC] trust the local apic timer
1155 libata.dma= [LIBATA] DMA control
1156 libata.dma=0 Disable all PATA and SATA DMA
1157 libata.dma=1 PATA and SATA Disk DMA only
1158 libata.dma=2 ATAPI (CDROM) DMA only
1159 libata.dma=4 Compact Flash DMA only
1160 Combinations also work, so libata.dma=3 enables DMA
1161 for disks and CDROMs, but not CFs.
1163 libata.ignore_hpa= [LIBATA] Ignore HPA limit
1164 libata.ignore_hpa=0 keep BIOS limits (default)
1165 libata.ignore_hpa=1 ignore limits, using full disk
1167 libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
1171 libata.force= [LIBATA] Force configurations. The format is comma
1172 separated list of "[ID:]VAL" where ID is
1173 PORT[:DEVICE]. PORT and DEVICE are decimal numbers
1174 matching port, link or device. Basically, it matches
1175 the ATA ID string printed on console by libata. If
1176 the whole ID part is omitted, the last PORT and DEVICE
1177 values are used. If ID hasn't been specified yet, the
1178 configuration applies to all ports, links and devices.
1180 If only DEVICE is omitted, the parameter applies to
1181 the port and all links and devices behind it. DEVICE
1182 number of 0 either selects the first device or the
1183 first fan-out link behind PMP device. It does not
1184 select the host link. DEVICE number of 15 selects the
1185 host link and device attached to it.
1187 The VAL specifies the configuration to force. As long
1188 as there's no ambiguity shortcut notation is allowed.
1189 For example, both 1.5 and 1.5G would work for 1.5Gbps.
1190 The following configurations can be forced.
1192 * Cable type: 40c, 80c, short40c, unk, ign or sata.
1193 Any ID with matching PORT is used.
1195 * SATA link speed limit: 1.5Gbps or 3.0Gbps.
1197 * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7].
1198 udma[/][16,25,33,44,66,100,133] notation is also
1201 * [no]ncq: Turn on or off NCQ.
1203 * nohrst, nosrst, norst: suppress hard, soft
1206 If there are multiple matching configurations changing
1207 the same attribute, the last one is used.
1209 lmb=debug [KNL] Enable lmb debug messages.
1211 load_ramdisk= [RAM] List of ramdisks to load from floppy
1212 See Documentation/blockdev/ramdisk.txt.
1214 lockd.nlm_grace_period=P [NFS] Assign grace period.
1217 lockd.nlm_tcpport=N [NFS] Assign TCP port.
1220 lockd.nlm_timeout=T [NFS] Assign timeout value.
1223 lockd.nlm_udpport=M [NFS] Assign UDP port.
1226 logibm.irq= [HW,MOUSE] Logitech Bus Mouse Driver
1229 loglevel= All Kernel Messages with a loglevel smaller than the
1230 console loglevel will be printed to the console. It can
1231 also be changed with klogd or other programs. The
1232 loglevels are defined as follows:
1234 0 (KERN_EMERG) system is unusable
1235 1 (KERN_ALERT) action must be taken immediately
1236 2 (KERN_CRIT) critical conditions
1237 3 (KERN_ERR) error conditions
1238 4 (KERN_WARNING) warning conditions
1239 5 (KERN_NOTICE) normal but significant condition
1240 6 (KERN_INFO) informational
1241 7 (KERN_DEBUG) debug-level messages
1243 log_buf_len=n Sets the size of the printk ring buffer, in bytes.
1244 Format: { n | nk | nM }
1245 n must be a power of two. The default size
1246 is set in the kernel config file.
1248 logo.nologo [FB] Disables display of the built-in Linux logo.
1249 This may be used to provide more screen space for
1250 kernel log messages and is useful when debugging
1251 kernel boot problems.
1253 lp=0 [LP] Specify parallel ports to use, e.g,
1254 lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses
1255 lp=reset first parallel port). 'lp=0' disables the
1256 lp=auto printer driver. 'lp=reset' (which can be
1257 specified in addition to the ports) causes
1258 attached printers to be reset. Using
1259 lp=port1,port2,... specifies the parallel ports
1260 to associate lp devices with, starting with
1261 lp0. A port specification may be 'none' to skip
1262 that lp device, or a parport name such as
1263 'parport0'. Specifying 'lp=auto' instead of a
1264 port specification list means that device IDs
1265 from each port should be examined, to see if
1266 an IEEE 1284-compliant printer is attached; if
1267 so, the driver will manage that printer.
1268 See also header of drivers/char/lp.c.
1271 Sets loops_per_jiffy to given constant, thus avoiding
1272 time-consuming boot-time autodetection (up to 250 ms per
1273 CPU). 0 enables autodetection (default). To determine
1274 the correct value for your kernel, boot with normal
1275 autodetection and see what value is printed. Note that
1276 on SMP systems the preset will be applied to all CPUs,
1277 which is likely to cause problems if your CPUs need
1278 significantly divergent settings. An incorrect value
1279 will cause delays in the kernel to be wrong, leading to
1280 unpredictable I/O errors and other breakage. Although
1281 unlikely, in the extreme case this might damage your
1285 Format: <io>,<irq>,<dma>
1287 mac5380= [HW,SCSI] Format:
1288 <can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags>
1290 machvec= [IA64] Force the use of a particular machine-vector
1291 (machvec) in a generic kernel.
1292 Example: machvec=hpzx1_swiotlb
1294 machtype= [Loongson] Share the same kernel image file between different
1296 Example: machtype=lemote-yeeloong-2f-7inch
1298 max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater
1299 than or equal to this physical address is ignored.
1301 maxcpus= [SMP] Maximum number of processors that an SMP kernel
1302 should make use of. maxcpus=n : n >= 0 limits the
1303 kernel to using 'n' processors. n=0 is a special case,
1304 it is equivalent to "nosmp", which also disables
1307 max_loop= [LOOP] Maximum number of loopback devices that can
1311 max_luns= [SCSI] Maximum number of LUNs to probe.
1312 Should be between 1 and 2^32-1.
1315 [SCSI] Maximum number of LUNs received.
1316 Should be between 1 and 16384.
1320 mce [X86-32] Machine Check Exception
1322 mce=option [X86-64] See Documentation/x86/x86_64/boot-options.txt
1324 md= [HW] RAID subsystems devices and level
1325 See Documentation/md.txt.
1328 Format: <first>,<last>
1329 Specifies range of consoles to be captured by the MDA.
1331 mem=nn[KMG] [KNL,BOOT] Force usage of a specific amount of memory
1332 Amount of memory to be used when the kernel is not able
1333 to see the whole system memory or for test.
1334 [X86-32] Use together with memmap= to avoid physical
1335 address space collisions. Without memmap= PCI devices
1336 could be placed at addresses belonging to unused RAM.
1338 mem=nopentium [BUGS=X86-32] Disable usage of 4MB pages for kernel
1342 [KNL,SH] Allow user to override the default size for
1343 per-device physically contiguous DMA buffers.
1345 memmap=exactmap [KNL,X86] Enable setting of an exact
1346 E820 memory map, as specified by the user.
1347 Such memmap=exactmap lines can be constructed based on
1348 BIOS output or other requirements. See the memmap=nn@ss
1351 memmap=nn[KMG]@ss[KMG]
1352 [KNL] Force usage of a specific region of memory
1353 Region of memory to be used, from ss to ss+nn.
1355 memmap=nn[KMG]#ss[KMG]
1356 [KNL,ACPI] Mark specific memory as ACPI data.
1357 Region of memory to be used, from ss to ss+nn.
1359 memmap=nn[KMG]$ss[KMG]
1360 [KNL,ACPI] Mark specific memory as reserved.
1361 Region of memory to be used, from ss to ss+nn.
1362 Example: Exclude memory from 0x18690000-0x1869ffff
1363 memmap=64K$0x18690000
1365 memmap=0x10000$0x18690000
1367 memory_corruption_check=0/1 [X86]
1368 Some BIOSes seem to corrupt the first 64k of
1369 memory when doing things like suspend/resume.
1370 Setting this option will scan the memory
1371 looking for corruption. Enabling this will
1372 both detect corruption and prevent the kernel
1373 from using the memory being corrupted.
1374 However, its intended as a diagnostic tool; if
1375 repeatable BIOS-originated corruption always
1376 affects the same memory, you can use memmap=
1377 to prevent the kernel from using that memory.
1379 memory_corruption_check_size=size [X86]
1380 By default it checks for corruption in the low
1381 64k, making this memory unavailable for normal
1382 use. Use this parameter to scan for
1383 corruption in more or less memory.
1385 memory_corruption_check_period=seconds [X86]
1386 By default it checks for corruption every 60
1387 seconds. Use this parameter to check at some
1388 other rate. 0 disables periodic checking.
1390 memtest= [KNL,X86] Enable memtest
1392 default : 0 <disable>
1393 Specifies the number of memtest passes to be
1394 performed. Each pass selects another test
1395 pattern from a given set of patterns. Memtest
1396 fills the memory with this pattern, validates
1397 memory contents and reserves bad memory
1398 regions that are detected.
1400 meye.*= [HW] Set MotionEye Camera parameters
1401 See Documentation/video4linux/meye.txt.
1403 mfgpt_irq= [IA-32] Specify the IRQ to use for the
1404 Multi-Function General Purpose Timers on AMD Geode
1407 mfgptfix [X86-32] Fix MFGPT timers on AMD Geode platforms when
1408 the BIOS has incorrectly applied a workaround. TinyBIOS
1409 version 0.98 is known to be affected, 0.99 fixes the
1410 problem by letting the user disable the workaround.
1414 min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
1415 physical address is ignored.
1417 mini2440= [ARM,HW,KNL]
1418 Format:[0..2][b][c][t]
1420 MINI2440 configuration specification:
1421 0 - The attached screen is the 3.5" TFT
1422 1 - The attached screen is the 7" TFT
1423 2 - The VGA Shield is attached (1024x768)
1424 Leaving out the screen size parameter will not load
1425 the TFT driver, and the framebuffer will be left
1427 b - Enable backlight. The TFT backlight pin will be
1428 linked to the kernel VESA blanking code and a GPIO
1429 LED. This parameter is not necessary when using the
1431 c - Enable the s3c camera interface.
1432 t - Reserved for enabling touchscreen support. The
1433 touchscreen support is not enabled in the mainstream
1434 kernel as of 2.6.30, a preliminary port can be found
1435 in the "bleeding edge" mini2440 support kernel at
1436 http://repo.or.cz/w/linux-2.6/mini2440.git
1439 [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
1440 parameter allows control of the logging verbosity for
1441 the additional memory initialisation checks. A value
1442 of 0 disables mminit logging and a level of 4 will
1443 log everything. Information is printed at KERN_DEBUG
1444 so loglevel=8 may also need to be specified.
1447 [MOUSE] Maximum time between finger touching and
1448 leaving touchpad surface for touch to be considered
1449 a tap and be reported as a left button click (for
1450 touchpads working in absolute mode only).
1452 mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices
1453 reporting absolute coordinates, such as tablets
1454 mousedev.yres= [MOUSE] Vertical screen resolution, used for devices
1455 reporting absolute coordinates, such as tablets
1457 movablecore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1458 is similar to kernelcore except it specifies the
1459 amount of memory used for migratable allocations.
1460 If both kernelcore and movablecore is specified,
1461 then kernelcore will be at *least* the specified
1462 value but may be more. If movablecore on its own
1463 is specified, the administrator must be careful
1464 that the amount of memory usable for all allocations
1470 MTD_Partition= [MTD]
1471 Format: <name>,<region-number>,<size>,<offset>
1473 MTD_Region= [MTD] Format:
1474 <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>]
1477 See drivers/mtd/cmdlinepart.c.
1479 onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
1481 Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
1483 boundary - index of last SLC block on Flex-OneNAND.
1484 The remaining blocks are configured as MLC blocks.
1485 lock - Configure if Flex-OneNAND boundary should be locked.
1486 Once locked, the boundary cannot be changed.
1487 1 indicates lock status, 0 indicates unlock status.
1490 ARM/S3C2412 JIVE boot control
1492 See arch/arm/mach-s3c2412/mach-jive.c
1494 mtouchusb.raw_coordinates=
1495 [HW] Make the MicroTouch USB driver use raw coordinates
1496 ('y', default) or cooked coordinates ('n')
1498 mtrr_chunk_size=nn[KMG] [X86]
1499 used for mtrr cleanup. It is largest continuous chunk
1500 that could hold holes aka. UC entries.
1502 mtrr_gran_size=nn[KMG] [X86]
1503 Used for mtrr cleanup. It is granularity of mtrr block.
1505 Large value could prevent small alignment from
1508 mtrr_spare_reg_nr=n [X86]
1510 Range: 0,7 : spare reg number
1512 Used for mtrr cleanup. It is spare mtrr entries number.
1513 Set to 2 or more if your graphical card needs more.
1515 n2= [NET] SDL Inc. RISCom/N2 synchronous serial card
1518 See header of drivers/scsi/NCR_D700.c.
1522 ncr53c400= [HW,SCSI]
1524 ncr53c400a= [HW,SCSI]
1526 ncr53c406a= [HW,SCSI]
1528 ncr53c8xx= [HW,SCSI]
1530 netdev= [NET] Network devices parameters
1531 Format: <irq>,<io>,<mem_start>,<mem_end>,<name>
1532 Note that mem_start is often overloaded to mean
1533 something different and driver-specific.
1534 This usage is only documented in each driver source
1538 [NETFILTER] Enable connection tracking flow accounting
1539 0 to disable accounting
1540 1 to enable accounting
1541 Default value depends on CONFIG_NF_CT_ACCT that is
1542 going to be removed in 2.6.29.
1545 See Documentation/filesystems/nfsroot.txt.
1547 nfsroot= [NFS] nfs root filesystem for disk-less boxes.
1548 See Documentation/filesystems/nfsroot.txt.
1550 nfs.callback_tcpport=
1551 [NFS] set the TCP port on which the NFSv4 callback
1552 channel should listen.
1555 [NFS] sets the pathname to the program which is used
1556 to update the NFS client cache entries.
1558 nfs.cache_getent_timeout=
1559 [NFS] sets the timeout after which an attempt to
1560 update a cache entry is deemed to have failed.
1562 nfs.idmap_cache_timeout=
1563 [NFS] set the maximum lifetime for idmapper cache
1567 [NFS] enable 64-bit inode numbers.
1568 If zero, the NFS client will fake up a 32-bit inode
1569 number for the readdir() and stat() syscalls instead
1570 of returning the full 64-bit number.
1571 The default is to return 64-bit inode numbers.
1573 nmi_debug= [KNL,AVR32,SH] Specify one or more actions to take
1574 when a NMI is triggered.
1575 Format: [state][,regs][,debounce][,die]
1577 nmi_watchdog= [KNL,BUGS=X86] Debugging features for SMP kernels
1578 Format: [panic,][num]
1580 0 - turn nmi_watchdog off
1581 1 - use the IO-APIC timer for the NMI watchdog
1582 2 - use the local APIC for the NMI watchdog using
1583 a performance counter. Note: This will use one
1584 performance counter and the local APIC's performance
1586 When panic is specified, panic when an NMI watchdog
1588 This is useful when you use a panic=... timeout and
1589 need the box quickly up again.
1590 Instead of 1 and 2 it is possible to use the following
1591 symbolic names: lapic and ioapic
1592 Example: nmi_watchdog=2 or nmi_watchdog=panic,lapic
1594 netpoll.carrier_timeout=
1595 [NET] Specifies amount of time (in seconds) that
1596 netpoll should wait for a carrier. By default netpoll
1599 no387 [BUGS=X86-32] Tells the kernel to use the 387 maths
1600 emulation library even if a 387 maths coprocessor
1604 [HW] Never suspend the console
1605 Disable suspending of consoles during suspend and
1606 hibernate operations. Once disabled, debugging
1607 messages can reach various consoles while the rest
1608 of the system is being put to sleep (ie, while
1609 debugging driver suspend/resume hooks). This may
1610 not work reliably with all consoles, but is known
1611 to work with serial and VGA consoles.
1613 noaliencache [MM, NUMA, SLAB] Disables the allocation of alien
1614 caches in the slab allocator. Saves per-node memory,
1615 but will impact performance.
1619 noapic [SMP,APIC] Tells the kernel to not make use of any
1620 IOAPICs that may be present in the system.
1622 nobats [PPC] Do not use BATs for mapping kernel lowmem
1623 on "Classic" PPC cores.
1627 noclflush [BUGS=X86] Don't use the CLFLUSH instruction
1629 nodelayacct [KNL] Disable per-task delay accounting
1631 nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects.
1633 nodsp [SH] Disable hardware DSP at boot time.
1635 noefi [X86] Disable EFI runtime services support.
1640 On X86-32 available only on PAE configured kernels.
1641 noexec=on: enable non-executable mappings (default)
1642 noexec=off: disable non-executable mappings
1645 This affects only 32-bit executables.
1646 noexec32=on: enable non-executable mappings (default)
1647 read doesn't imply executable mappings
1648 noexec32=off: disable non-executable mappings
1649 read implies executable mappings
1651 nofpu [SH] Disable hardware FPU at boot time.
1653 nofxsr [BUGS=X86-32] Disables x86 floating point extended
1654 register save and restore. The kernel will only save
1655 legacy floating-point registers on task switch.
1657 noxsave [BUGS=X86] Disables x86 extended register state save
1658 and restore using xsave. The kernel will fallback to
1659 enabling legacy floating-point and sse state.
1661 nohlt [BUGS=ARM,SH] Tells the kernel that the sleep(SH) or
1662 wfi(ARM) instruction doesn't work correctly and not to
1663 use it. This is also useful when using JTAG debugger.
1665 no-hlt [BUGS=X86-32] Tells the kernel that the hlt
1666 instruction doesn't work correctly and not to
1669 no_file_caps Tells the kernel not to honor file capabilities. The
1670 only way then for a file to be executed with privilege
1671 is to be setuid root or executed by root.
1673 nohalt [IA-64] Tells the kernel not to use the power saving
1674 function PAL_HALT_LIGHT when idle. This increases
1675 power-consumption. On the positive side, it reduces
1676 interrupt wake-up latency, which may improve performance
1677 in certain environments such as networked servers or
1680 nohz= [KNL] Boottime enable/disable dynamic ticks
1681 Valid arguments: on, off
1684 noiotrap [SH] Disables trapped I/O port accesses.
1686 noirqdebug [X86-32] Disables the code which attempts to detect and
1687 disable unhandled interrupt sources.
1689 no_timer_check [X86,APIC] Disables the code which tests for
1690 broken timer IRQ sources.
1692 noisapnp [ISAPNP] Disables ISA PnP code.
1694 noinitrd [RAM] Tells the kernel not to load any configured
1697 nointremap [X86-64, Intel-IOMMU] Do not enable interrupt
1702 nojitter [IA64] Disables jitter checking for ITC timers.
1704 nolapic [X86-32,APIC] Do not enable or use the local APIC.
1706 nolapic_timer [X86-32,APIC] Do not use the local APIC timer.
1708 noltlbs [PPC] Do not use large page/tlb entries for kernel
1709 lowmem mapping on PPC40x.
1711 nomca [IA-64] Disable machine check abort handling
1713 nomce [X86-32] Machine Check Exception
1715 nomfgpt [X86-32] Disable Multi-Function General Purpose
1716 Timer usage (for AMD Geode machines).
1718 norandmaps Don't use address space randomization. Equivalent to
1719 echo 0 > /proc/sys/kernel/randomize_va_space
1721 noreplace-paravirt [X86-32,PV_OPS] Don't patch paravirt_ops
1723 noreplace-smp [X86-32,SMP] Don't replace SMP instructions
1724 with UP alternatives
1726 noresidual [PPC] Don't use residual data on PReP machines.
1728 noresume [SWSUSP] Disables resume and restores original swap
1731 no-scroll [VGA] Disables scrollback.
1732 This is required for the Braillex ib80-piezo Braille
1733 reader made by F.H. Papenmeier (Germany).
1737 nosep [BUGS=X86-32] Disables x86 SYSENTER/SYSEXIT support.
1739 nosmp [SMP] Tells an SMP kernel to act as a UP kernel,
1740 and disable the IO APIC. legacy for "maxcpus=0".
1742 nosoftlockup [KNL] Disable the soft-lockup detector.
1744 noswapaccount [KNL] Disable accounting of swap in memory resource
1745 controller. (See Documentation/cgroups/memory.txt)
1747 nosync [HW,M68K] Disables sync negotiation for all devices.
1749 notsc [BUGS=X86-32] Disable Time Stamp Counter
1751 nousb [USB] Disable the USB subsystem
1755 nox2apic [X86-64,APIC] Do not enable x2APIC mode.
1757 nptcg= [IA64] Override max number of concurrent global TLB
1758 purges which is reported from either PAL_VM_SUMMARY or
1761 nr_uarts= [SERIAL] maximum number of UARTs to be registered.
1763 numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA.
1764 one of ['zone', 'node', 'default'] can be specified
1765 This can be set from sysctl after boot.
1766 See Documentation/sysctl/vm.txt for details.
1768 ohci1394_dma=early [HW] enable debugging via the ohci1394 driver.
1769 See Documentation/debugging-via-ohci1394.txt for more
1772 olpc_ec_timeout= [OLPC] ms delay when issuing EC commands
1773 Rather than timing out after 20 ms if an EC
1774 command is not properly ACKed, override the length
1775 of the timeout. We have interrupts disabled while
1776 waiting for the ACK, so if this is set too high
1777 interrupts *may* be lost!
1782 oprofile.timer= [HW]
1783 Use timer interrupt instead of performance counters
1785 oprofile.cpu_type= Force an oprofile cpu type
1786 This might be useful if you have an older oprofile
1787 userland or if you want common events.
1788 Format: { arch_perfmon }
1789 arch_perfmon: [X86] Force use of architectural
1790 perfmon on Intel CPUs instead of the
1791 CPU specific event set.
1793 osst= [HW,SCSI] SCSI Tape Driver
1794 Format: <buffer_size>,<write_threshold>
1795 See also Documentation/scsi/st.txt.
1797 panic= [KNL] Kernel behaviour on panic
1800 parkbd.port= [HW] Parallel port number the keyboard adapter is
1801 connected to, default is 0.
1803 parkbd.mode= [HW] Parallel port keyboard adapter mode of operation,
1804 0 for XT, 1 for AT (default is AT).
1807 parport= [HW,PPT] Specify parallel ports. 0 disables.
1808 Format: { 0 | auto | 0xBBB[,IRQ[,DMA]] }
1809 Use 'auto' to force the driver to use any
1810 IRQ/DMA settings detected (the default is to
1811 ignore detected IRQ/DMA settings because of
1812 possible conflicts). You can specify the base
1813 address, IRQ, and DMA settings; IRQ and DMA
1814 should be numbers, or 'auto' (for using detected
1815 settings on that particular port), or 'nofifo'
1816 (to avoid using a FIFO even if it is detected).
1817 Parallel ports are assigned in the order they
1818 are specified on the command line, starting
1821 parport_init_mode= [HW,PPT]
1822 Configure VIA parallel port to operate in
1823 a specific mode. This is necessary on Pegasos
1824 computer where firmware has no options for setting
1825 up parallel port mode and sets it to spp.
1826 Currently this function knows 686a and 8231 chips.
1827 Format: [spp|ps2|epp|ecp|ecpepp]
1829 pas2= [HW,OSS] Format:
1830 <io>,<irq>,<dma>,<dma16>,<sb_io>,<sb_irq>,<sb_dma>,<sb_dma16>
1833 See header of drivers/scsi/pas16.c.
1836 Halt all CPUs after the first oops has been printed for
1837 the specified number of seconds. This is to be used if
1838 your oopses keep scrolling off the screen.
1843 See header of drivers/block/paride/pcd.c.
1844 See also Documentation/blockdev/paride.txt.
1846 pci=option[,option...] [PCI] various PCI subsystem options:
1847 earlydump [X86] dump PCI config space before the kernel
1849 off [X86] don't probe for the PCI bus
1850 bios [X86-32] force use of PCI BIOS, don't access
1851 the hardware directly. Use this if your machine
1852 has a non-standard PCI host bridge.
1853 nobios [X86-32] disallow use of PCI BIOS, only direct
1854 hardware access methods are allowed. Use this
1855 if you experience crashes upon bootup and you
1856 suspect they are caused by the BIOS.
1857 conf1 [X86] Force use of PCI Configuration
1859 conf2 [X86] Force use of PCI Configuration
1861 noaer [PCIE] If the PCIEAER kernel config parameter is
1862 enabled, this kernel boot option can be used to
1863 disable the use of PCIE advanced error reporting.
1864 nodomains [PCI] Disable support for multiple PCI
1865 root domains (aka PCI segments, in ACPI-speak).
1866 nommconf [X86] Disable use of MMCONFIG for PCI
1868 check_enable_amd_mmconf [X86] check for and enable
1869 properly configured MMIO access to PCI
1870 config space on AMD family 10h CPU
1871 nomsi [MSI] If the PCI_MSI kernel config parameter is
1872 enabled, this kernel boot option can be used to
1873 disable the use of MSI interrupts system-wide.
1874 noioapicquirk [APIC] Disable all boot interrupt quirks.
1875 Safety option to keep boot IRQs enabled. This
1876 should never be necessary.
1877 ioapicreroute [APIC] Enable rerouting of boot IRQs to the
1878 primary IO-APIC for bridges that cannot disable
1879 boot IRQs. This fixes a source of spurious IRQs
1880 when the system masks IRQs.
1881 noioapicreroute [APIC] Disable workaround that uses the
1882 boot IRQ equivalent of an IRQ that connects to
1883 a chipset where boot IRQs cannot be disabled.
1884 The opposite of ioapicreroute.
1885 biosirq [X86-32] Use PCI BIOS calls to get the interrupt
1886 routing table. These calls are known to be buggy
1887 on several machines and they hang the machine
1888 when used, but on other computers it's the only
1889 way to get the interrupt routing table. Try
1890 this option if the kernel is unable to allocate
1891 IRQs or discover secondary PCI buses on your
1893 rom [X86] Assign address space to expansion ROMs.
1894 Use with caution as certain devices share
1895 address decoders between ROMs and other
1897 norom [X86] Do not assign address space to
1898 expansion ROMs that do not already have
1899 BIOS assigned address ranges.
1900 irqmask=0xMMMM [X86] Set a bit mask of IRQs allowed to be
1901 assigned automatically to PCI devices. You can
1902 make the kernel exclude IRQs of your ISA cards
1904 pirqaddr=0xAAAAA [X86] Specify the physical address
1905 of the PIRQ table (normally generated
1906 by the BIOS) if it is outside the
1907 F0000h-100000h range.
1908 lastbus=N [X86] Scan all buses thru bus #N. Can be
1909 useful if the kernel is unable to find your
1910 secondary buses and you want to tell it
1911 explicitly which ones they are.
1912 assign-busses [X86] Always assign all PCI bus
1913 numbers ourselves, overriding
1914 whatever the firmware may have done.
1915 usepirqmask [X86] Honor the possible IRQ mask stored
1916 in the BIOS $PIR table. This is needed on
1917 some systems with broken BIOSes, notably
1918 some HP Pavilion N5400 and Omnibook XE3
1919 notebooks. This will have no effect if ACPI
1920 IRQ routing is enabled.
1921 noacpi [X86] Do not use ACPI for IRQ routing
1922 or for PCI scanning.
1923 use_crs [X86] Use _CRS for PCI resource
1925 routeirq Do IRQ routing for all PCI devices.
1926 This is normally done in pci_enable_device(),
1927 so this option is a temporary workaround
1928 for broken drivers that don't call it.
1929 skip_isa_align [X86] do not align io start addr, so can
1930 handle more pci cards
1931 firmware [ARM] Do not re-enumerate the bus but instead
1932 just use the configuration from the
1933 bootloader. This is currently used on
1934 IXP2000 systems where the bus has to be
1935 configured a certain way for adjunct CPUs.
1936 noearly [X86] Don't do any early type 1 scanning.
1937 This might help on some broken boards which
1938 machine check when some devices' config space
1939 is read. But various workarounds are disabled
1940 and some IOMMU drivers will not work.
1941 bfsort Sort PCI devices into breadth-first order.
1942 This sorting is done to get a device
1943 order compatible with older (<= 2.4) kernels.
1944 nobfsort Don't sort PCI devices into breadth-first order.
1945 cbiosize=nn[KMG] The fixed amount of bus space which is
1946 reserved for the CardBus bridge's IO window.
1947 The default value is 256 bytes.
1948 cbmemsize=nn[KMG] The fixed amount of bus space which is
1949 reserved for the CardBus bridge's memory
1950 window. The default value is 64 megabytes.
1953 [<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...]
1954 Specifies alignment and device to reassign
1955 aligned memory resources.
1956 If <order of align> is not specified,
1957 PAGE_SIZE is used as alignment.
1958 PCI-PCI bridge can be specified, if resource
1959 windows need to be expanded.
1960 ecrc= Enable/disable PCIe ECRC (transaction layer
1961 end-to-end CRC checking).
1962 bios: Use BIOS/firmware settings. This is the
1967 pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power
1970 force Enable ASPM even on devices that claim not to support it.
1971 WARNING: Forcing ASPM on may cause system lockups.
1973 pcmv= [HW,PCMCIA] BadgePAD 4
1976 See Documentation/blockdev/paride.txt.
1978 pdcchassis= [PARISC,HW] Disable/Enable PDC Chassis Status codes at
1981 See arch/parisc/kernel/pdc_chassis.c
1983 percpu_alloc= Select which percpu first chunk allocator to use.
1984 Currently supported values are "embed" and "page".
1985 Archs may support subset or none of the selections.
1986 See comments in mm/percpu.c for details on each
1987 allocator. This parameter is primarily for debugging
1988 and performance comparison.
1991 See Documentation/blockdev/paride.txt.
1994 See Documentation/blockdev/paride.txt.
1996 pirq= [SMP,APIC] Manual mp-table setup
1997 See Documentation/x86/i386/IO-APIC.txt.
1999 plip= [PPT,NET] Parallel port network link
2000 Format: { parport<nr> | timid | 0 }
2001 See also Documentation/parport.txt.
2003 pmtmr= [X86] Manual setup of pmtmr I/O Port.
2004 Override pmtimer IOPort with a hex value.
2008 Enable PNP debug messages. This depends on the
2009 CONFIG_PNP_DEBUG_MESSAGES option.
2015 { on | off | curr | res | no-curr | no-res }
2018 [ISAPNP] Exclude IRQs for the autoconfiguration
2021 [ISAPNP] Exclude DMAs for the autoconfiguration
2023 pnp_reserve_io= [ISAPNP] Exclude I/O ports for the autoconfiguration
2024 Ranges are in pairs (I/O port base and size).
2027 [ISAPNP] Exclude memory regions for the
2029 Ranges are in pairs (memory base and size).
2031 ports= [IP_VS_FTP] IPVS ftp helper module
2033 Up to 8 (IP_VS_APP_MAX_PORTS) ports
2035 Format: <port>,<port>....
2037 print-fatal-signals=
2038 [KNL] debug: print fatal signals
2039 print-fatal-signals=1: print segfault info to
2043 printk.time= Show timing data prefixed to each printk message line
2044 Format: <bool> (1/Y/y=enable, 0/N/n=disable)
2046 processor.max_cstate= [HW,ACPI]
2047 Limit processor to maximum C-state
2048 max_cstate=9 overrides any DMI blacklist limit.
2050 processor.nocst [HW,ACPI]
2051 Ignore the _CST method to determine C-states,
2052 instead using the legacy FADT method
2054 profile= [KNL] Enable kernel profiling via /proc/profile
2055 Format: [schedule,]<number>
2056 Param: "schedule" - profile schedule points.
2057 Param: <number> - step/bucket size as a power of 2 for
2058 statistical time based profiling.
2059 Param: "sleep" - profile D-state sleeping (millisecs).
2060 Requires CONFIG_SCHEDSTATS
2061 Param: "kvm" - profile VM exits.
2063 prompt_ramdisk= [RAM] List of RAM disks to prompt for floppy disk
2065 See Documentation/blockdev/ramdisk.txt.
2067 psmouse.proto= [HW,MOUSE] Highest PS2 mouse protocol extension to
2068 probe for; one of (bare|imps|exps|lifebook|any).
2069 psmouse.rate= [HW,MOUSE] Set desired mouse report rate, in reports
2071 psmouse.resetafter= [HW,MOUSE]
2072 Try to reset the device after so many bad packets
2075 [HW,MOUSE] Set desired mouse resolution, in dpi.
2076 psmouse.smartscroll=
2077 [HW,MOUSE] Controls Logitech smartscroll autorepeat.
2078 0 = disabled, 1 = enabled (default).
2080 pss= [HW,OSS] Personal Sound System (ECHO ESC614)
2082 <io>,<mss_io>,<mss_irq>,<mss_dma>,<mpu_io>,<mpu_irq>
2085 See Documentation/blockdev/paride.txt.
2088 [KNL] Number of legacy pty's. Overwrites compiled-in
2091 quiet [KNL] Disable most log messages
2096 See Documentation/md.txt.
2098 ramdisk_blocksize= [RAM]
2099 See Documentation/blockdev/ramdisk.txt.
2101 ramdisk_size= [RAM] Sizes of RAM disks in kilobytes
2102 See Documentation/blockdev/ramdisk.txt.
2104 rcupdate.blimit= [KNL,BOOT]
2105 Set maximum number of finished RCU callbacks to process
2108 rcupdate.qhimark= [KNL,BOOT]
2109 Set threshold of queued
2110 RCU callbacks over which batch limiting is disabled.
2112 rcupdate.qlowmark= [KNL,BOOT]
2113 Set threshold of queued RCU callbacks below which
2114 batch limiting is re-enabled.
2118 Run specified binary instead of /init from the ramdisk,
2119 used for early userspace startup. See initrd.
2121 reboot= [BUGS=X86-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
2122 Format: <reboot_mode>[,<reboot_mode2>[,...]]
2123 See arch/*/kernel/reboot.c or arch/*/kernel/process.c
2126 [KNL, SMP] Set scheduler's default relax_domain_level.
2127 See Documentation/cgroups/cpusets.txt.
2129 reserve= [KNL,BUGS] Force the kernel to ignore some iomem area
2131 reservetop= [X86-32]
2133 Reserves a hole at the top of the kernel virtual
2136 reset_devices [KNL] Force drivers to reset the underlying device
2137 during initialization.
2140 Specify the partition device for software suspend
2142 resume_offset= [SWSUSP]
2143 Specify the offset from the beginning of the partition
2144 given by "resume=" at which the swap header is located,
2145 in <PAGE_SIZE> units (needed only for swap files).
2146 See Documentation/power/swsusp-and-swap-files.txt
2148 retain_initrd [RAM] Keep initrd memory after extraction
2150 rhash_entries= [KNL,NET]
2151 Set number of hash buckets for route cache
2153 riscom8= [HW,SERIAL]
2154 Format: <io_board1>[,<io_board2>[,...<io_boardN>]]
2156 ro [KNL] Mount root device read-only on boot
2158 root= [KNL] Root filesystem
2160 rootdelay= [KNL] Delay (in seconds) to pause before attempting to
2161 mount the root filesystem
2163 rootflags= [KNL] Set root filesystem mount option string
2165 rootfstype= [KNL] Set root filesystem type
2167 rootwait [KNL] Wait (indefinitely) for root device to show up.
2168 Useful for devices that are detected asynchronously
2169 (e.g. USB and MMC devices).
2171 root_plug.vendor_id=
2172 [ROOTPLUG] Override the default vendor ID
2174 root_plug.product_id=
2175 [ROOTPLUG] Override the default product ID
2178 [ROOTPLUG] Enable debugging output
2180 rw [KNL] Mount root device read-write on boot
2182 S [KNL] Run init in single mode
2185 See drivers/net/irda/sa1100_ir.c.
2187 sbni= [NET] Granch SBNI12 leased line adapter
2189 sc1200wdt= [HW,WDT] SC1200 WDT (watchdog) driver
2190 Format: <io>[,<timeout>[,<isapnp>]]
2192 scsi_debug_*= [SCSI]
2193 See drivers/scsi/scsi_debug.c.
2195 scsi_default_dev_flags=
2196 [SCSI] SCSI default device flags
2199 scsi_dev_flags= [SCSI] Black/white list entry for vendor and model
2200 Format: <vendor>:<model>:<flags>
2201 (flags are integer value)
2203 scsi_logging_level= [SCSI] a bit mask of logging levels
2204 See drivers/scsi/scsi_logging.h for bits. Also
2205 settable via sysctl at dev.scsi.logging_level
2206 (/proc/sys/dev/scsi/logging_level).
2207 There is also a nice 'scsi_logging_level' script in the
2208 S390-tools package, available for download at
2209 http://www-128.ibm.com/developerworks/linux/linux390/s390-tools-1.5.4.html
2211 scsi_mod.scan= [SCSI] sync (default) scans SCSI busses as they are
2212 discovered. async scans them in kernel threads,
2213 allowing boot to proceed. none ignores them, expecting
2214 user space to do the scan.
2216 security= [SECURITY] Choose a security module to enable at boot.
2217 If this boot parameter is not specified, only the first
2218 security module asking for security registration will be
2219 loaded. An invalid security module name will be treated
2220 as if no module has been chosen.
2222 selinux= [SELINUX] Disable or enable SELinux at boot time.
2223 Format: { "0" | "1" }
2224 See security/selinux/Kconfig help text.
2227 Default value is set via kernel config option.
2228 If enabled at boot time, /selinux/disable can be used
2229 later to disable prior to initial policy load.
2231 serialnumber [BUGS=X86-32]
2234 Maximal number of shapers.
2236 show_msr= [x86] show boot-time MSR settings
2237 Format: { <integer> }
2238 Show boot-time (BIOS-initialized) MSR settings.
2239 The parameter means the number of CPUs to show,
2240 for example 1 means boot CPU only.
2243 See header of drivers/scsi/sim710.c.
2250 slub_debug[=options[,slabs]] [MM, SLUB]
2251 Enabling slub_debug allows one to determine the
2252 culprit if slab objects become corrupted. Enabling
2253 slub_debug can create guard zones around objects and
2254 may poison objects when not in use. Also tracks the
2255 last alloc / free. For more information see
2256 Documentation/vm/slub.txt.
2258 slub_max_order= [MM, SLUB]
2259 Determines the maximum allowed order for slabs.
2260 A high setting may cause OOMs due to memory
2261 fragmentation. For more information see
2262 Documentation/vm/slub.txt.
2264 slub_min_objects= [MM, SLUB]
2265 The minimum number of objects per slab. SLUB will
2266 increase the slab order up to slub_max_order to
2267 generate a sufficiently large slab able to contain
2268 the number of objects indicated. The higher the number
2269 of objects the smaller the overhead of tracking slabs
2270 and the less frequently locks need to be acquired.
2271 For more information see Documentation/vm/slub.txt.
2273 slub_min_order= [MM, SLUB]
2274 Determines the mininum page order for slabs. Must be
2275 lower than slub_max_order.
2276 For more information see Documentation/vm/slub.txt.
2278 slub_nomerge [MM, SLUB]
2279 Disable merging of slabs with similar size. May be
2280 necessary if there is some reason to distinguish
2281 allocs to different slabs. Debug options disable
2282 merging on their own.
2283 For more information see Documentation/vm/slub.txt.
2286 Format: <io1>[,<io2>[,...,<io8>]]
2288 smp-alt-once [X86-32,SMP] On a hotplug CPU system, only
2289 attempt to substitute SMP alternatives once at boot.
2291 smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices
2292 smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port
2293 smsc-ircc2.ircc_sir= [HW] SIR base I/O port
2294 smsc-ircc2.ircc_fir= [HW] FIR base I/O port
2295 smsc-ircc2.ircc_irq= [HW] IRQ line
2296 smsc-ircc2.ircc_dma= [HW] DMA channel
2297 smsc-ircc2.ircc_transceiver= [HW] Transceiver type:
2298 0: Toshiba Satellite 1800 (GP data pin select)
2299 1: Fast pin select (default)
2302 snd-ad1816a= [HW,ALSA]
2304 snd-ad1848= [HW,ALSA]
2306 snd-ali5451= [HW,ALSA]
2308 snd-als100= [HW,ALSA]
2310 snd-als4000= [HW,ALSA]
2312 snd-azt2320= [HW,ALSA]
2314 snd-cmi8330= [HW,ALSA]
2316 snd-cmipci= [HW,ALSA]
2318 snd-cs4231= [HW,ALSA]
2320 snd-cs4232= [HW,ALSA]
2322 snd-cs4236= [HW,ALSA]
2324 snd-cs4281= [HW,ALSA]
2326 snd-cs46xx= [HW,ALSA]
2328 snd-dt019x= [HW,ALSA]
2330 snd-dummy= [HW,ALSA]
2332 snd-emu10k1= [HW,ALSA]
2334 snd-ens1370= [HW,ALSA]
2336 snd-ens1371= [HW,ALSA]
2338 snd-es968= [HW,ALSA]
2340 snd-es1688= [HW,ALSA]
2342 snd-es18xx= [HW,ALSA]
2344 snd-es1938= [HW,ALSA]
2346 snd-es1968= [HW,ALSA]
2348 snd-fm801= [HW,ALSA]
2350 snd-gusclassic= [HW,ALSA]
2352 snd-gusextreme= [HW,ALSA]
2354 snd-gusmax= [HW,ALSA]
2358 snd-ice1712= [HW,ALSA]
2360 snd-intel8x0= [HW,ALSA]
2362 snd-interwave= [HW,ALSA]
2367 snd-korg1212= [HW,ALSA]
2369 snd-maestro3= [HW,ALSA]
2371 snd-mpu401= [HW,ALSA]
2373 snd-mtpav= [HW,ALSA]
2375 snd-nm256= [HW,ALSA]
2377 snd-opl3sa2= [HW,ALSA]
2385 snd-opti93x= [HW,ALSA]
2389 snd-rme32= [HW,ALSA]
2391 snd-rme96= [HW,ALSA]
2393 snd-rme9652= [HW,ALSA]
2399 snd-sbawe= [HW,ALSA]
2401 snd-serial= [HW,ALSA]
2403 snd-sgalaxy= [HW,ALSA]
2405 snd-sonicvibes= [HW,ALSA]
2410 snd-sun-cs4231= [HW,ALSA]
2412 snd-trident= [HW,ALSA]
2414 snd-usb-audio= [HW,ALSA,USB]
2416 snd-via82xx= [HW,ALSA]
2418 snd-virmidi= [HW,ALSA]
2420 snd-wavefront= [HW,ALSA]
2422 snd-ymfpci= [HW,ALSA]
2425 [KNL] Should the soft-lockup detector generate panics.
2427 sonypi.*= [HW] Sony Programmable I/O Control Device driver
2428 See Documentation/sonypi.txt
2430 specialix= [HW,SERIAL] Specialix multi-serial port adapter
2431 See Documentation/serial/specialix.txt.
2433 spia_io_base= [HW,MTD]
2439 Format: <io>,<irq>,<dma>,<mpu_io>,<mpu_irq>
2441 st= [HW,SCSI] SCSI tape parameters (buffers, etc.)
2442 See Documentation/scsi/st.txt.
2445 Enabled the stack tracer on boot up.
2449 Set the STI (builtin display/keyboard on the HP-PARISC
2450 machines) console (graphic card) which should be used
2451 as the initial boot-console.
2452 See also comment in drivers/video/console/sticore.c.
2455 See comment in drivers/video/console/sticore.c.
2458 Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
2460 sunrpc.min_resvport=
2461 sunrpc.max_resvport=
2463 SunRPC servers often require that client requests
2464 originate from a privileged port (i.e. a port in the
2465 range 0 < portnr < 1024).
2466 An administrator who wishes to reserve some of these
2467 ports for other uses may adjust the range that the
2468 kernel's sunrpc client considers to be privileged
2469 using these two parameters to set the minimum and
2470 maximum port values.
2474 Control how the NFS server code allocates CPUs to
2475 service thread pools. Depending on how many NICs
2476 you have and where their interrupts are bound, this
2477 option will affect which CPUs will do NFS serving.
2478 Note: this parameter cannot be changed while the
2479 NFS server is running.
2481 auto the server chooses an appropriate mode
2482 automatically using heuristics
2483 global a single global pool contains all CPUs
2484 percpu one pool for each CPU
2485 pernode one pool for each NUMA node (equivalent
2486 to global on non-NUMA machines)
2488 sunrpc.tcp_slot_table_entries=
2489 sunrpc.udp_slot_table_entries=
2491 Sets the upper limit on the number of simultaneous
2492 RPC calls that can be sent from the client to a
2493 server. Increasing these values may allow you to
2494 improve throughput, but will also increase the
2495 amount of memory reserved for use by the client.
2497 swiotlb= [IA-64] Number of I/O TLB slabs
2501 sym53c416= [HW,SCSI]
2502 See header of drivers/scsi/sym53c416.c.
2504 sysrq_always_enabled
2506 Ignore sysrq setting - this boot parameter will
2507 neutralize any effect of /proc/sys/kernel/sysrq.
2508 Useful for debugging.
2511 See header of drivers/scsi/t128.c.
2515 test_suspend= [SUSPEND]
2516 Specify "mem" (for Suspend-to-RAM) or "standby" (for
2517 standby suspend) as the system sleep state to briefly
2518 enter during system startup. The system is woken from
2519 this state using a wakeup-capable RTC alarm.
2521 thash_entries= [KNL,NET]
2522 Set number of hash buckets for TCP connection
2524 thermal.act= [HW,ACPI]
2525 -1: disable all active trip points in all thermal zones
2526 <degrees C>: override all lowest active trip points
2528 thermal.crt= [HW,ACPI]
2529 -1: disable all critical trip points in all thermal zones
2530 <degrees C>: override all critical trip points
2532 thermal.nocrt= [HW,ACPI]
2533 Set to disable actions on ACPI thermal zone
2534 critical and hot trip points.
2536 thermal.off= [HW,ACPI]
2537 1: disable ACPI thermal control
2539 thermal.psv= [HW,ACPI]
2540 -1: disable all passive trip points
2541 <degrees C>: override all passive trip points to this
2544 thermal.tzp= [HW,ACPI]
2545 Specify global default ACPI thermal zone polling rate
2546 <deci-seconds>: poll all this frequency
2547 0: no polling (default)
2550 See comment before function dc390_setup() in
2551 drivers/scsi/tmscsim.c.
2555 Specify if the kernel should make use of the cpu
2556 topology informations if the hardware supports these.
2557 The scheduler will make use of these informations and
2558 e.g. base its process migration decisions on it.
2563 trace_buf_size=nn[KMG]
2564 [FTRACE] will set tracing buffer size.
2566 trace_event=[event-list]
2567 [FTRACE] Set and start specified trace events in order
2568 to facilitate early boot debugging.
2569 See also Documentation/trace/events.txt
2571 trix= [HW,OSS] MediaTrix AudioTrix Pro
2573 <io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
2575 tsc= Disable clocksource-must-verify flag for TSC.
2577 [x86] reliable: mark tsc clocksource as reliable, this
2578 disables clocksource verification at runtime.
2579 Used to enable high-resolution timer mode on older
2580 hardware, and in virtualized environment.
2581 [x86] noirqtime: Do not use TSC to do irq accounting.
2582 Used to run time disable IRQ_TIME_ACCOUNTING on any
2583 platforms where RDTSC is slow and this accounting
2586 turbografx.map[2|3]= [HW,JOY]
2587 TurboGraFX parallel port interface
2589 <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7>
2590 See also Documentation/input/joystick-parport.txt
2592 u14-34f= [HW,SCSI] UltraStor 14F/34F SCSI host adapter
2593 See header of drivers/scsi/u14-34f.c.
2602 [USB] Ignore overcurrent events (default N).
2603 Some badly-designed motherboards generate lots of
2604 bogus events, for ports that aren't wired to
2605 anything. Set this parameter to avoid log spamming.
2606 Note that genuine overcurrent events won't be
2611 Set unknown_nmi_panic=1 early on boot.
2613 usbcore.autosuspend=
2614 [USB] The autosuspend time delay (in seconds) used
2615 for newly-detected USB devices (default 2). This
2616 is the time required before an idle device will be
2617 autosuspended. Devices for which the delay is set
2618 to a negative value won't be autosuspended at all.
2620 usbcore.usbfs_snoop=
2621 [USB] Set to log all usbfs traffic (default 0 = off).
2623 usbcore.blinkenlights=
2624 [USB] Set to cycle leds on hubs (default 0 = off).
2626 usbcore.old_scheme_first=
2627 [USB] Start with the old device initialization
2628 scheme (default 0 = off).
2630 usbcore.use_both_schemes=
2631 [USB] Try the other device initialization scheme
2632 if the first one fails (default 1 = enabled).
2634 usbcore.initial_descriptor_timeout=
2635 [USB] Specifies timeout for the initial 64-byte
2636 USB_REQ_GET_DESCRIPTOR request in milliseconds
2637 (default 5000 = 5.0 seconds).
2640 [USBHID] The interval which mice are to be polled at.
2642 usb-storage.delay_use=
2643 [UMS] The delay in seconds before a new device is
2644 scanned for Logical Units (default 5).
2647 [UMS] A list of quirks entries to supplement or
2648 override the built-in unusual_devs list. List
2649 entries are separated by commas. Each entry has
2650 the form VID:PID:Flags where VID and PID are Vendor
2651 and Product ID values (4-digit hex numbers) and
2652 Flags is a set of characters, each corresponding
2653 to a common usb-storage quirk flag as follows:
2654 a = SANE_SENSE (collect more than 18 bytes
2656 b = BAD_SENSE (don't collect more than 18
2657 bytes of sense data);
2658 c = FIX_CAPACITY (decrease the reported
2659 device capacity by one sector);
2660 h = CAPACITY_HEURISTICS (decrease the
2661 reported device capacity by one
2662 sector if the number is odd);
2663 i = IGNORE_DEVICE (don't bind to this
2665 l = NOT_LOCKABLE (don't try to lock and
2666 unlock ejectable media);
2667 m = MAX_SECTORS_64 (don't transfer more
2668 than 64 sectors = 32 KB at a time);
2669 o = CAPACITY_OK (accept the capacity
2670 reported by the device);
2671 r = IGNORE_RESIDUE (the device reports
2672 bogus residue values);
2673 s = SINGLE_LUN (the device has only one
2675 w = NO_WP_DETECT (don't test whether the
2676 medium is write-protected).
2677 Example: quirks=0419:aaf5:rl,0421:0433:rc
2680 [X86] Flags controlling user PTE allocations.
2682 nohigh = do not allocate PTE pages in
2683 HIGHMEM regardless of setting
2687 vdso=2: enable compat VDSO (default with COMPAT_VDSO)
2688 vdso=1: enable VDSO (default)
2689 vdso=0: disable VDSO mapping
2692 vdso32=2: enable compat VDSO (default with COMPAT_VDSO)
2693 vdso32=1: enable 32-bit VDSO (default)
2694 vdso32=0: disable 32-bit VDSO mapping
2697 vector=percpu: enable percpu vector domain
2699 video= [FB] Frame buffer configuration
2700 See Documentation/fb/modedb.txt.
2702 vga= [BOOT,X86-32] Select a particular video mode
2703 See Documentation/x86/boot.txt and
2704 Documentation/svga.txt.
2705 Use vga=ask for menu.
2706 This is actually a boot loader parameter; the value is
2707 passed to the kernel using a special protocol.
2709 vmalloc=nn[KMG] [KNL,BOOT] Forces the vmalloc area to have an exact
2710 size of <nn>. This can be used to increase the
2711 minimum size (128MB on x86). It can also be used to
2712 decrease the size and leave more room for directly
2715 vmhalt= [KNL,S390] Perform z/VM CP command after system halt.
2718 vmpanic= [KNL,S390] Perform z/VM CP command after kernel panic.
2721 vmpoff= [KNL,S390] Perform z/VM CP command after power off.
2724 vt.default_blu= [VT]
2725 Format: <blue0>,<blue1>,<blue2>,...,<blue15>
2726 Change the default blue palette of the console.
2727 This is a 16-member array composed of values
2730 vt.default_grn= [VT]
2731 Format: <green0>,<green1>,<green2>,...,<green15>
2732 Change the default green palette of the console.
2733 This is a 16-member array composed of values
2736 vt.default_red= [VT]
2737 Format: <red0>,<red1>,<red2>,...,<red15>
2738 Change the default red palette of the console.
2739 This is a 16-member array composed of values
2745 Set system-wide default UTF-8 mode for all tty's.
2746 Default is 1, i.e. UTF-8 mode is enabled for all
2747 newly opened terminals.
2749 waveartist= [HW,OSS]
2750 Format: <io>,<irq>,<dma>,<dma2>
2753 See header of drivers/scsi/wd33c93.c.
2756 See header of drivers/scsi/wd7000.c.
2759 See Documentation/watchdog/wdt.txt.
2761 x2apic_phys [X86-64,APIC] Use x2apic physical mode instead of
2762 default x2apic cluster mode on platforms
2765 xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks.
2766 xd_geo= See header of drivers/block/xd.c.
2768 xirc2ps_cs= [NET,PCMCIA]
2770 <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
2772 ______________________________________________________________________
2776 Add documentation for ALSA options.
2777 Add more DRM drivers.
projects / firefly-linux-kernel-4.4.55.git / blob